DEVELOPMENT OF PARK IN KODERMA THANA, UNDER NAGAR PANCHAYAT KODERMA

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earthwork in hard soil as per specification and direction of E/I. ( vide classification of soil item-B)

Earth filling in foundaion trenches and plinth in layers not exceding 150 mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50 M and lift of 1.5 M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75B one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level.1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete

Providing designation 75 B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including, providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/I.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mmnominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Providing tor steel reinforcement of 8mm.,10mm,12mmm&16mmmdia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. Taking 8mm TMT FE 500 ( only valid for Tata (Tiscon) SAIL, JSPL, Electro Steels Ltd., Bokaro, & Vizag (RINL)

10mm Dia

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and laying vitrified floor tile in different size (thickness to be specified by the manufacturer) water absorption less than 0.08% and confirming to IS15622/ISO-13006 of approved make, in all color and shade, laid on 20mm thick cement mortar (1:4) , jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigment etc. complete.

Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Supplying, fitting and fixing M.S. grill gate with M.S. grill made of 20X6mm M.S. flats or 16mm M.S. square bars fitted on 25X25X6mm M.S. Angle frame of size 60X60X6mm. Including cost of fabrication, providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/I.

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding , curing and taxes all complete as per building specification and direction of E/I.

Providing primer one coat of red lead paint of approved make over new steel surface including preparing the surface after cleaning, removing dust, dirt, scales smokes and grease and cleaning the surface throughly including cost of scaffolding and taxes all complete as per building specification and direction of E/I. (Mode of measurement area shall be multiplied by the co-efficient as indicated in building specification)

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

16.91.2 Providing and laying factory made coloured chamfered edge cement concrete paver block of required strength , thickness and size/shape, made by vibratory method using PU mould laid in required colour & pattern over 50mm thick compacted bed of fine sand ,compacting and proper embedding /laying of inter locking paver blocks in to the sand bedding layer through vibratory compaction by using plate vibrator , filling the joints with sand and cutting the paver blocks as per required size and pattern ,finishing and sweeping extra sand in footpath parks, lawns, drive ways or light traffic parking etc. complete as per manufacturer's specifications and direction of E/I.16.91.1 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5mm), including making drainage opening wherever required complete etc. as per direction of Engineer-in-charge (length of finished kerb edging shall be measured for payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).[dsr 16.69]

Providing and Displaying Ficus reginold well developed fresh & healthy foliage 60 to 75 cm spread 105 to 120 cm ht., Bushy in 35 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Cyprus golden well shaped developed with good colored foliage fresh & healthy 60 to 75 cm ht in 30 cm Earthen Pot as per direction of the officer-in-charge.

Supply , stacking & filling of good earth at site including cost of royalty & carriage upto 5 Km ( Earth measured in stacks will be reduced by 20% for payment ) .

Providing and laying in position cement concrete of specified grade excluding the cost of centering, shuttering , finishing and reinforcement all work up to plinth level 1:2:4 (1 cement : 2 coarse zone III : 4 grade stone )aggregate 20 mm nominal size.

The spiral slide is made up of Fiber Reinforced Plastic (FRP) in 3 parts with holding having shell thickness of 3-4 mm. The slide is supported on a center support of 80 NB GI pipe. The landing supports of the slide are supported by 20 NB pipes. The slide ladder is made up of 40 NB GI pipe & ladder hand-railing is made up of 25 NB GI pipe. The triangular steps of the ladder are made up of 16 SWG GI sheets. The safety railing of the slide is made up of 15 NB & 20 NB GI pipes. The trader and riser of the ladder are designed in such a way it won’t entrap child’s foot while playing. All the sharp edges and corners are properly grinded to give smooth finish so that children are not hurt while playing on it.

As the name suggests, this product has a combination of three products such as swing, slide and seesaw. The complete frame of this product is fabricated from 20 NB and 25 NB powder coated GI pipes. The slide in the combination set is made up of Fiber reinforced plastic (FRP). The slide landing support is made in 20 NB pipe. The slides are given a smooth finish so that the child does not hurt itself while playing on it. The bucket swing is made up of LLDPE and is attached to a nylon rope. For the bucket swing a handle is given for gripping, which is made in rotational molding and out of LLDPE. The see-saw lever and stand is made up of 20 NB GI pipe. The see saw seat is made out of LLDPE. The bearing used is of heavy-duty bush type.

The Multi Seater See saw comprises four Rotational seats. The lever consists of 20 NB and 80 NB powder coated GI pipes. The bearing used in this product is heavy duty nylon bush type. The stand for see saw is made using 50 NB GI pipe.

As the name suggests, four children can enjoy the four seater arc swing at one time. The arched shaped side frame is made of 80 NB GI pipes and top pipe is made up of 50 NB GI pipes. The frame is powder coated to give an esthetic look. The four swings are made up of 10 mm thick anti-skid chequered reinforced rubber top. The rubber belt seat is suspended on 6 mm rubber coated GI chain. The ball bearings are mounted inside a specially designed nylon clamp.

The trampoline is helpful in the entertainment and growth of the children. It consists of 25 NB powder coated GI pipes. The canvas provided in the middle is kept stretched with the help of high-tension springs. A cover is provided to the trampoline to hide the springs and gives an esthetic look to the product. Six nos of Leg pipes provided for stand are made up of 25NB G.I. pipes. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All the sharp edges and corners are properly grinded to give smooth finish so that children are not hurt while playing on it

The main frame of LEG LIFT POST is made up of 80 NB G.I. pipes. 6 no of spacer pipes made by 25 NB G.I. pipes are arranged parallel at equidistance to form a back rest of product. The paired handle pipe consists of 25NB galvanized pipe fixed at the top and bottom of 80NB support pipe main frame. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment.

The main frame of ABS BOARD is made up of 80 NB G.I. pipes with leg support structure. The back rest is fixed over 40NB back rest frame. Back rest is made up of rectangular pipes of 50 X 25 X 3 mm thick. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe closed by GI / HDPE caps for user safety against entrapment.

CHEST PRESS & SHOULDER EXERCISER COMBINATION-The center frame of the Chest Press & Shoulder Exerciser Combination is made up of 80NB G.I. pipe bend and FRP sheet. Specially designed brackets are bolted to center frame. These brackets are made of M.S. material with G.I. plating. The connecting links are made of 40NB G.I. pipes which are mounted to main frame with the help of specially designed machined shaft and bearing housings. The handle frame is made of 25 NB galvanized pipe. Handle is linked to the seat with 40NB pipe which is hinged to main vertical support pipe with the help of specially designed bearing assemblies. FRP / HDPE / LLDPE plastic seat fixed over 40 NB G.I. pipe seat frames. This seat frame is hinged over vertical support pipe through 40NB galvanized pipe links with the help of specially designed bearing assemblies. Bearings used are oil sealed, self-lubricated made by reputed company. Foot rest is made up of 20 NB G.I. pipes. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment.

The main frame of Hip Twister Double consists of 80 NB G.I. pipes with handle attached on it. Rectangular shaped handles are mounted in certain angle on main frame. Handle pipe is made up of 25 NB G.I. pipe. The rotating discs made from M.S. material with G.I. plating are supported over 80NB G.I. pipes stands with the help of specially designed heavy duty bearings. The discs are bolted to main frame with the help of 40NB G.I. pipe. Three foundation stands, made of 80 NB G.I. pipes and G.I. plated M.S. round plates are provided. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment.

LEG PRESS-The main support frame of Leg Press Single is made up of 40NB G.I. pipe bend and G.I. sheet with two specially designed brackets attached on it. Brackets are made of M.S. material with G.I. plating. The moving frame of Leg Press is made of 40NB G.I. pipes which are mounted to main frame with the help of specially designed, machined shaft and bearing housing. Bearings used are oil sealed, self-lubricated made by reputed company. Foot rest is hinged to main frame with the help of specially designed G.I. plated clamp and 25 NB G.I. pipes. Gusset plates are provided to give extra strength to foot rest. Foot rest is made of high quality FRP (Fiber Reinforced Plastic) material. Specially designed Nylon pads are provided at the bottom of moving frame. Seat and back rest provided are made of FRP/ LLDPE / HDPE plastic. All pipes are uniformly powder coated up to minimum 60 micron thickness to avoid corrosion. All open ends of pipe been closed by GI / HDPE caps for user safety against entrapment.

Carriage of materials by mechanical means including loading,unloading and stacking at work site Bricks

Chips

Cement

Steel

Labour Cess 1%

PHOTO & SIGN