Loading
Loading…
Loading…
Tender Value
₹3.6 Cr
EMD Value
₹3.3 L
Closing Date
10 Feb 2026, 3:00 pmClosed
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
DYCEEC JHS
18 conditions · 2 needing a document upload
Financial Eligibility Criteria (As per GCC Part-I clause No.10.2 (Advance Correction Slip No. 1)): The tenderer must have minimum average annual contractual turnover of V/N or V whichever is less, where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB (Format attached with tender document details & in GCC), along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet.
Tenderers should upload the documents in support of minimum eligibility criteria. No documents other than uploaded documents in support of minimum eligibility criteria will be accepted / entertained after closing of tender.
Technical Eligibility Criteria (As per GCC Part-I clause No.10.1): (a) The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii)Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iv)One similar work costing not less than the amount equal to 60% of advertised value of the tender. (b)(1) In case of tenders for composite works (e.g. works involving more than one distinct component, such as Civil Engineering works, S&T works, Electrical works, OHE works etc. and in the case of major bridges - substructure, superstructure etc.), tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited: (i) Three similar works each costing not less than the amount equal to 30% of advertised value of each component of tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of each component of tender, or (iii) One similar work each costing not less than the amount equal to 60% of advertised value of each component of tender. Note for b(1): Separate completed works of minimum required values shall also be considered for fulfillment of technical eligibility criteria for different components. (b) (2)In such cases, what constitutes a component in a composite work shall be clearly pre-defined with estimated tender cost of it, as part of the tender documents without any ambiguity. (b) (3) To evaluate the technical eligibility of tenderer, only components of work as stipulated in tender documents for evaluation of technical eligibility, shall be considered. The scope of work covered in other remaining components shall be either executed by tenderer himself if he has work experience as mentioned in clause 7 of the Standard General Conditions of Contractor through subcontractor fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract or jointly i.e., partly himself and remaining through subcontractor, with prior approval of Chief Engineer in writing. However, if required in tender documents by way of Special Conditions, a formal agreement duly notarized, legally enforceable in the court of law, shall be executed by the main contractor with the subcontractor for the component(s) of work proposed to be executed by the subcontractor(s), and shall be submitted along with the offer for considering subletting of that scope of work towards fulfillment of technical eligibility. Such subcontractor must fulfill technical eligibility criteria as follows:
The subcontractor shall have successfully completed at least one work similar to work proposed for subcontract, costing not less than 35% value of work to be subletted, in last 5 years, ending last day of month previous to the one in which tender is invited through a works contract. Note: for subletting of work costing up to Rs 50 lakh, no previous work experience of sub-contractor shall be asked for by the Railway. In case after award of contract or during execution of work it becomes necessary for contractor to change subcontractor, the same shall be done with subcontractor(s) fulfilling the requirements as per clause 7 of the Standard General Conditions of Contract, with prior approval of Chief Engineer in writing. Note for Item 10.1 of GCC Part-I: Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates. In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
Definition of similar single work is as under: "Satisfactory execution of any electrical work related to HT/LT Installation".
Tenderers are advised to go through the explanation for Para 10.1 to 10.5 - Eligibility Criteria of GCC April'22 Part-I before submitting their offer.
Tenderers should upload the documents in support of minimum eligibility criteria. No documents other than uploaded documents in support of minimum eligibility criteria will be accepted / entertained after closing of tender.
63 conditions · 22 needing a document upload
The tenderer must ensure to furnish applicable documents, declaration and certificates as per the check list attached with this tender as description " Check list".
EMD (bid security)form as indicated in the NIT header shall be paid through online' gate way/E-Payment facility provided on IREPS website. Other mode of payment towards EMD (bid security) be accepted as per the guidelines provided in GCC April'2022. In case payment of EMD is not successful during E- payment, the offer will be summarily rejected. If bid security deposited by the tenderer other than the online gateway/e- payment facility provided in IREPS website, the instrument of bid security should be favour of Dy.FA&CAO(C)/NCR/JHS otherwise offer will be treated as invalid. In case Bid Security deposited in form of Bank Guarantee, the original Bank Guarantee should be delivered in person to the official nominated as indicated in the tender document before closing date for submission of bids (i.e. excluding the last date of submission of bids). In case payment of EMD is not successful during E-payment, the offer will be summarily rejected.
Tenderer should submit documents related to Registration details, GSTIN alongwith other details required under CGST/IGST/UTGST/SGST Act, registered address, email ID etc.
As per clause No. 14 of GCC Part-I, Documents to be Submitted Along with Tender: Partnership Deeds, Power of Attorney etc.: (i)The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm/company/Joint Venture (JV) /Registered Society/Registered Trust/ Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. The tenderer(s) shall enclose the attested copies of the constitution of their concern, and copy of PAN Card along with their tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (ii)Following documents shall be submitted by the tenderer: (a)Sole Proprietorship Firm: (i)All documents in terms of GCC Part-I Para 10 of the Tender Form (Second Sheet). (b)HUF: (i)A copy of notarized affidavit on Stamp Paper declaring that he who is submitting the tender on behalf of HUF is in the position of 'Karta' of Hindu Undivided Family (HUF) and he has the authority, power and consent given by other members to act on behalf of HUF. (ii)All other documents in terms of GCC Part-I Para 10 of the Tender Form (Second Sheet). (c)Partnership Firm:(i)All documents as mentioned in GCC Part-I para18 of the Tender Form (Second Sheet).(d)Joint Venture (JV): All documents as mentioned in GCC Part-I para 17 of the Tender Form (Second Sheet).(e)Company registered under Companies Act2013:(i)The copies of MOA (Memorandum of Association) / AOA (Articles of Association) of the company(ii)A copy of Certificate of Incorporation(iii)A copy of Authorization/Power of Attorney issued by the Company (backed by the resolution of Board of Directors) in favour of the individual to sign the tender on behalf of the company and create liability against the company.(iv)All other documents in terms GCC Part-I Para 10 of the Tender Form (Second Sheet).
(f)LLP (Limited Liability Partnership): (i)A copy of LLP Agreement. (ii)A copy of Certificate of Incorporation (iii)A copy of Power of Attorney/Authorization issued by the LLP in favour of the individual to sign the tender on behalf of the LLP and create liability against the LLP. (iv)An undertaking by all partners of the LLP that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP or JV in which they were / are partners/members. Concealment / wrong information in regard to above shall make the contract liable for determination under Clause 62 of the Standard General Conditions of Contract. (v)All other documents in terms of GCC Part-I Para 10 of the Tender Form (Second Sheet). (g) Registered Society & Registered Trust: (i) A copy of Certificate of Registration. (ii)A copy of Memorandum of Association of Society/Trust Deed (iii)A copy of Power of Attorney in favour of the individual to sign the tender documents and create liability against the Society/Trust. (iv) A copy of Rules & Regulations of the Society. (v) All other documents in terms of GCC Part-I Para 10 of the Tender Form (Second Sheet).(iii) If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm/Partnership firm/Joint Venture/Registered Company etc., then the tender shall be treated as having been submitted by the individual who has signed the tender. (iv) After opening of the tender, any document pertaining to the constitution of Sole Proprietorship Firm/Partnership Firm/Registered Company/Registered Trust/Registered Society/HUF/LLP etc. shall be neither asked nor considered, if submitted.(v)A tender from JV / Partnership firm etc. shall be considered only where permissible as per the tender conditions. (vi)The Railway will not be bound by any change of power of attorney or in the composition of the firm made subsequent to the submission of tender. Railway may, however, recognize such power of attorney and changes after obtaining proper legal advice, the cost of which will be chargeable to the Contractor.
As per Para 15 of GCC Part-I:- The tenderer whether sole proprietor/a company or a partnership firm / joint venture (JV) /registered society /registered trust / HUF / LLP etc if they want to act through agent or individual partner(s), should submit along with the tender, a copy of power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, specifically authorizing him/them to sign the tender, submit the tender and further to deal with the Tender/ Contract up to the stage of signing the agreement except in case where such specific person is authorized for above purposes through a provision made in the partnership deed / Memorandum of Understanding / Article of Association/Board resolution, failing which tender shall be summarily rejected. A separate power of attorney duly stamped and authenticated by a Notary Public or by Magistrate in favour of the specific person whether he/they be partner(s) of the firm or any other person, shall be submitted after award of work, specifically authorizing him/them to deal with all other contractual activities subsequent to signing of agreement, if required. Note: A Power of Attorney executed and issued overseas, the document will also have to be legalized by the Indian Embassy and notarized in the jurisdiction where the Power of Attorney is being issued. However, the Power of Attorney provided by Bidders from countries that have signed the Hague Legislation Convention 1961 are not required to be legalized by the Indian Embassy if it carries a conforming Appostille certificate
As per Clause-18 of GCC part-I, in case of participation in tender by Partnership firm, the tenderer shall clearly specify that the tender is submitted on behalf of a partnership firm. The following documents shall be submitted by the partnership firm, with the tender:(i) A notarized copy of the Partnership Deed or a copy of the Partnership deed registered with the Registrar. (ii) A notarized or registered copy of Power of Attorney in favour of the individual to tender for the work, sign the agreement etc. and create liability against the firm.(iii) An undertaking by all partners of the partnership firm that they are not blacklisted or debarred by Railways or any other Ministry / Department of the Govt. of India from participation in tenders / contracts as on the date of submission of bids, either in their individual capacity or in any firm/LLP in which they were / are partners/members. Any Concealment / wrong information in regard to above shall make the bid ineligible or the contract shall be determined under Clause 62 of the Standard General Conditions of Contract.(iv) All other documents in terms of Para 10 of GCC Part-I.
The tenderer is must to submit the Proprietorship certificate/Partnership deed alongwith Power of Attorney/AOA and MOA alongwith Power of Attorney issued by the Company (backed by the resolution of Board of Directors) alongwith their offer, as the case may be. Power of Attorney should be in favour of the person who will digitally sign the bid as well as other documents enclosed by the bidder alongwith their offer.
Generally deviations of contractor against the Railways specification & special conditions stipulated in the entire tender booklet are not acceptable. Therefore, tenderers are advised not to quote any deviation against the Railways conditions & specification stipulated in tender document. However, deviation if any should be evaluated in financial term and rate quoted accordingly i.e. deviations should be considered into rates.
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Credentials of Tenderers: The tenderers shall provide satisfactory documentary evidences acceptable to Railway (certificate from private individuals for whom such works are executed / being executed will not be accepted) along with the tender to show that:
They have an established technically competent and adequate staff organization to ensure that the services required under this tender can do satisfactorily. The Tenderer shall provide the list of personnel available in hand and proposed to be inducted for the subject work along with the offer.
They have sufficient equipments; plants and machinery to meet the obligations under the contract and to complete the work contract all within the stipulated time schedule and accepted by him. The Tenderer shall provide the list of equipments, plants and machinery available in hand and proposed to be inducted (own and hired basis separately) for the subject work along with the offer.
The Tenderer should also give details of advisory or technical collaboration with original equipment manufacturer in consultation with whom equipment has been designed and / or whose specifications are utilized in manufacturing of the equipments being supplied.
The Tenderer should submit the details of all similar works done in the past.
The Tenderer should submit the attested copies of the certificates obtained from the agencies wherever the works have completed successfully. These certificates should indicate the details of installation and successful commissioning of the similar type of equipments executed by the Tenderer.
The Tenderer will submit, along with offer list of work in hand indicating description of work, contract value, approximate value of balance work yet to be done and date of award of work.
They have adequate financial resources to meet the obligations under the contract. They have to submit the report from recognized bank or financial institutions.
Please submit your bank details i.e. Name of the Bank along with Bank Branch Code, IFSC Code, Beneficiary name, Account Number, Type of account, PAN and GSTN Number.
Balance Electrification of Offices, Depots, Platforms, Station Buildings, Cabins, IBH, Level Crossing Gates, FOB, Staff Quarters etc. coming in the work of 3rd Line of JHS - BINA Section of Jhansi Division in North Central Railway.
JHS-DY-CEE-C-T-07-2025~NCR
JHS-DY-CEE-C-T-07-2025
Open
Works - General
6 Months
Prayagraj, Uttar Pradesh
₹0
₹3.3 L
10 Feb 2026
16 Jan 2026
27 Jan 2026
219 items across 1 schedule
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| — | — | — | 3,60,11,905.71 | ||
| — | 520.00 | — | — | ||
| Supply of materials & making wiring point for various fittings/fans /indication light etc. with 2x2.5 sqmm (FRLS) PVC insulated multi-stranded copper conductor cable single core conforming to IS : 694 (latest version) in surface PVC casing, capping channel heavy duty/in recessed PVC with continuous pvc insulated copper earth wire of 1.5 sq.mm. | — | — | — | 3,00,918.8 | |
| — | 70.00 | — | — | ||
| Supply of materials & making wiring point of 6 pin combined power point 5A/15A with wiring by 2x4 sqmm PVC insulated multistrand copper conductor cable (FRLS) single core conforming to IS : 694 (latest version) in PVC casing capping channel heavy duty,/in recessed PVC with continuous pvc insulated copper earth wire of 1.5 sq.mm. | — | — | — | 61,988.5 | |
| — | 140.00 | — | — | ||
| Supply, Erection, Testing, and Commissioning of 5 pin 5 Amp plug socket with 2x2.5 sq. mm PVC insulated multi strand copper conductor cable (FRLS) single core confirming to IS694 (latest version) in PVC casing capping channel heavy duty/in recessed PVC conduit pipe heavy duty with ISI mark with 5 Amp switch on front of hylmsheet top teakwood board/MS box of suitable size with brass screw cup washer etc. complete with continuous pvc insulated copper earth wire of 1.5 sq.mm. | — | — | — | 20,662.6 | |
| — | 60.00 | — | — | ||
| Supply, and fixing of surface mounted down light with white powder coated poly carbonate housing and fresher dia. cast heat sink heavy high efficiency integral ( surface ) 10W , CAT LOG No. LHEAAGP6PL1W010, fixture size in mm dia. 200, height 69, LED fitting. | — | — | — | 61,788 | |
| — | 185.00 | — | — | ||
| Supply ,Erection, Testing and Commissioning & fixing along with fan hook etc. of 1200mm sweep ceiling fan 4 blade complete with down rod as per suitable length , electronics regulator with PVC insulated flexible copper cable with flexible PVC pipe. | — | — | — | 3,28,424.95 | |
| — | 25.00 | — | — | ||
| Supply , erecting , Testing & Commissioning of exhaust fan 380 mm sweep , 1400 RPM , four blade, suitable to work on 230V AC supply .It should be fixed on wall with reg bolt, nut washer etc. | — | — | — | 58,786.5 | |
| — | 21.00 | — | — | ||
| Supply and Erection of 3 pin power socket 20 A /230V in sheet steel enclosure with 20A single pole MCB, 3 pin metal plug, and wiring by 2x6 sq.mm PVC insulated multi-stranded copper wire (FRLS) confirming to IS: 694 in recessed PVC conduit pipe heavy duty/ in PVC casing capping channel heavy duty with ISI mark complete in all respect separate circuit to be drawn from SDB including earth continuity wire | — | — | — | 14,989.38 | |
| — | 16.00 | — | — | ||
| Supply , Erection, Testing and Commissioning of metal clade 8 way SDB complete with 1x40Amp isolator DP & 4x5A to 40A MCB , SP complete with all other accessories as per site requirement. | — | — | — | 24,895.36 | |
| — | 290.00 | — | — | ||
| Supply, Fixing of 2x10 sq. mm PVC insulated copper cable single core 1100 v grade as per IS : 694 (latest ) for sub mains with PVC conduit pipe heavy duty not less than 25 mm dia. in recessed /surface of the wall with earth continuity PVC copper wire (Size 1 Sq.mm ) including , Erection Testing and Commissioning. | — | — | — | 36,029.6 | |
| — | 380.00 | — | — | ||
| Supply, of 4 x 10 mm2 PVC insulated copper cable single core 1100 v grade as per IS : 694 (latest ) for sub mains with PVC conduit pipe heavy duty not less than 25mm dia. in recessed /surface of the wall with earth continuity PVC copper wire including, Erection Testing and Commissioning, from LT panel to power SDBs. | — | — | — | 79,534 | |
| — | 520.00 | — | — | ||
| Supply and Erection of 5x10 sq. mm PVC insulated , PVC sheathed, copper wire . The sub mains shall be supported on suitable MS bracket by means of reel type porcelain insulators to be fixed with the truss of the covered shed FOB with one earth wire of 8 SWG GI Wire | — | — | — | 1,39,188.4 | |
| — | 410.00 | — | — | ||
| Supply & Erection of powder coated perforated cable tray 300x50x1.6 mm thick for protection of cabes comlete with all other accessories as per site requirement ( for supply arrangement through FOB and COP | — | — | — | 1,75,385.7 | |
| — | 35.00 | — | — | ||
| Erection of automatic voltage stabilizer 5 KVA suitable to work on 230V AC supply AC units | — | — | — | 42,332.5 | |
| — | 12.00 | — | — | ||
| Erection Testing and Commissioning of 63 A , 4 pole 30 KA MCCB with board of suitable size | — | — | — | 13,856.64 | |
| — | 12.00 | — | — | ||
| Erection Testing and Commissioning of 100-125 A, 4 pole MCCB with board of suitable size | — | — | — | 14,192.76 | |
| — | 320.00 | — | — | ||
| Supply & Erection of pipe earth electrode of 50 mm dia. 3m long, GI pipe Class B conforming to IS :1239 latest complete with earth box including connection from earth electrode to MDB/SDB/poles /with 8 SWG GI wire | — | — | — | 7,33,254.4 | |
| — | 2.00 | — | — | ||
| Supply, Erection, Testing ,and Commissioning of electrically driven submersible pump set water lubricated , 3 phase 415 V, 50Hz AC induction motor cap upto 5 HP in bore well 150mm/200mm dia. , with all accessories. Discharge on/or within the range of 62 to 180 LPM total head on or within or upto the range of 122 to 30 mtrs. outlet 50mm water lubricated. | — | — | — | 80,808.4 | |
| — | 2.00 | — | — | ||
| Supply , Erection, Testing ,and Commissioning of electrically driven submersible pump set water lubricated , single phase 230 V , 50Hz AC induction motor cap up to 03 HP in bore well 100mm/200mm dia. , with all accessories. Discharge on/or within the range of 70 to 110LPM total head on or within or upto the range of 68 to 100 mtrs. outlet 50mm water lubricated | — | — | — | 39,134.24 | |
| — | 603.00 | — | — | ||
| Supply of submersible PVC insulated steel wire rope braking strength not less than 2.50 kg per feet. | — | — | — | 15,087.06 | |
| — | 9.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of reflux valve ISI mark suitable for sub- mersible pump set complete with all fixing accessories conforming to relevant IS (latest) | — | — | — | 26,664.03 | |
| — | 5.00 | — | — | ||
| Supply, Erection , Testing and Commissioning of main control panel board made out of 14 SWG MS sheet of suitable size cubicle type , with locking arrangement . All equipment to be mounted on Bakelite sheet not less than 6mm thick consisting of 1x 32 A ,TPN MCB ,DOL /Star Delta starter , flush type ammeter, voltmeter , connection strip, indication lamps, capacitor bank of 4 KVAR MPP type, including control wiring , earth terminal , time switch for operation of switch etc. complete | — | — | — | 1,46,782.6 | |
| — | 252.00 | — | — | ||
| Supply, Erection , Testing and Commissioning of water proof, flat submersible cable ISI mark of size not less than 6 sqmm , copper conductor , 3 core, 1.1kv grade conforming to IS:694 / 1991 (latest) to be laid from starter to pump motor .From starter to well cable to be laid through MS conduit pipe (heavy guage) of suitable size with fixing accessories. | — | — | — | 37,613.52 | |
| — | 600.00 | — | — | ||
| Supply and fixing of GI pipe class 'B' as per IS:1239 Pt I latest of size 50 mm dia. with all fixing accessories for fixing of pump set with seamless coupling with locking devices , screwed both side only, or complete with MS round flange , rubber gasket , of not less than 5mm thick , with nut bolt, spring washer etc. including connection to Rly's delivery pipe line . Each length of pipe should be 3 mtr. approx." | — | — | — | 1,73,106 | |
| — | 700.00 | — | — | ||
| Supply & Erection, of GI bracket single arm type ,Class B as per IS:1239 latest, of required size and length with all fixing accessories suitable to fix on the wall of the rail pole/ building to hold street type fittings 85w/150w. | — | — | — | 56,616 | |
| — | 700.00 | — | — | ||
| Erection of swaged type Steel Tubular Poles conforming to IS:2713 Part I & II of 1980 (latest) with base plate ,earthing bolt , digging of pit in ground making CC foundation , Erection of pole vertically , painting complete 7 mtr long steel tubular pole designation 410-SP-3 with single arm bracket & double arm bracket. | — | — | — | 11,77,078 | |
| — | 1012.00 | — | — | ||
| Supply & Erection of GI pipe class 'B' as per IS: 1239 PT 1 latest of size 38 mm dia with all fixing accessories on steel tubular poles. | — | — | — | 61,600.44 | |
| — | 203.00 | — | — | ||
| Supply & Erection of MS junction box of size 250x200x175mm whether proof with locking arrangement duly painted consisting of 1x16A porcelain cut out , 4way porcelain connector | — | — | — | 66,693.62 | |
| — | 1000.00 | — | — | ||
| Erection, Testing and commission of 1*45 Watt street light LED with fittings pressure die cast aluminum housing, reflector and enclosed with toghened glass IP65. complete with suitable size GI bracket, copper connection wire and all other fixing accessories as per site requirement. | — | — | — | 18,18,880 | |
| — | 200.00 | — | — | ||
| Erection, Testing and commission of 1*30 Watt street light LED with fittings pressure die cast aluminium housing, reflector and enclosed with toghened glass IP65. complete with suitable size GI bracket | — | — | — | 1,86,116 | |
| — | 439.00 | — | — | ||
| Supply of material & Termination of XLPE LT cables of various sizes | — | — | — | 30,383.19 | |
| — | 1.00 | — | — | ||
| Supply, Erection, Testing, and Commissioning of battery charging rectifier set complete with all accessories having inpuyt of 3phase 415 V AC and out put 110 V to 150 V DC at 200 Amps cap. The rectifier set shall have 2 sets knief switch as per specification including masonary work required at the site. | — | — | — | 1,82,693.2 | |
| — | 10.00 | — | — | ||
| Supply, fabrication, fixing, and Commissioning of battery charging board/box emergency feed terminal box two way out door type for 150 V DC supply system as per specification including vertical grouting of MS channel 300mm deep with cement, sand and concrete mixture for Erection. | — | — | — | 25,549.2 | |
| — | 10.00 | — | — | ||
| Erection, Testing, and Commissioning of AC precooling MS box size 90x45x15 cm having cutler hammer 500 V 63 Amps Socket switch unit combined set including bus bar chamber 200A capacity complete with cable bushing for incoming and out going cable | — | — | — | 66,274.4 | |
| — | 200.00 | — | — | ||
| Supply and Erection of auxiliary cable tray made from angle 35x35x5mm and MS flat 35x5mm to be fixed on already fixed rail poles . | — | — | — | 69,042 | |
| — | 2.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of pillar type MDB outdoor type, weather proof, floor mounting type of suitable size made out from MS enclosure sheet 1.6 mm thick on outer side and 2.5 mm thick centre plate, M.S. angle of required size complete with locking arrangement, centre opening door, painting (red oxide primary coat followed by 2 coat of AI paint). The MDB shall be mounted on the brick masonary foundation of suitable sixe at the height of 300 mm from the gound level. Main TPN bus bar inside MDB shall be of copper strip 300 A capacity, fitted on the post type porcelain insulators. | — | — | — | 14,395.58 | |
| — | 2.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of following accessories in MDB along with Switch fuse unit TPN, 200/415V conforming to IS: 13947 (Pt I&II latest ) with rewirable poecelain fuse unit & sheet steel enclosure complete. | — | — | — | 14,914.24 | |
| — | 2.00 | — | — | ||
| Erection , Testing, & Commissioning of 500 KVA Transformers 11/0.4kv ,copper wound oil immersed , indoor type /out door type energy efficient (level-2 ) ( as per IS 1180-2014) distribution transformer with tapping range +5% to - 10% in steps of 2.5% by off circuit tape changer , vector group Dyn 11, impedance 4.50% | — | — | — | 5,42,836.4 | |
| — | 1.00 | — | — | ||
| Erection, Testing and Commissioning of 11 KV HT panel board 250MVA, 400A capacity ,consisting of 1 no incoming 3 pole Vacuum Circuit breaker conforming to IS:13118 (latest ) with PT ,electro magnetic relays , tri-vector meter , PF meter , voltmeter, ammeter with selector switch , | — | — | — | 4,79,116.9 | |
| — | 1.00 | — | — | ||
| Erection of cubicle floor mounted type , dust & vermin proof , weather proof , in-door type LT panel suitable for operation on 3phase 4 wire , 415 V ,AC supply system fabricated with 14 SWG MS sheet ,base MS angle 50x50x6 mm , MS channel 75x40x3 mm .It shall be coated with 2 coats approved colour | — | — | — | 2,03,190.2 | |
| — | 8.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of out door /indoor type cable end- termination kit/ straight through jointing kit with all accessories for 3 core 70 sqmm 11kv(E) XLPE cable as per relevant IS specification. | — | — | — | 50,944.88 | |
| — | 8.00 | — | — | ||
| Supply & Erection of earth electrode with 600x600x3 mm thick copper plate earth electrode as per IS 3043/1987 (Latest Verson), to achieve earth resistance less than one Ohm including construction of masonary enclosure with hinged cover plate of cast iron with locking arrangement on top watering pipe connection from earth plate to top with 50mm dia x 3000 mm GI pipe class B as per drawing and provision of earth plate | — | — | — | 48,536.72 | |
| — | 250.00 | — | — | ||
| Supply & Erection of copper strip 20x3mm as per IS 3043/1987 (Latest Versiion) 300 mm deep, in ground/recessing in floor for neutral of transformer as per relavent IS. | — | — | — | 1,55,930 | |
| — | 12.00 | — | — | ||
| Supply & Erection of earth electrode with 600x600x6 mm thick GI plate earth electrode as per IS 3043/1987 (Latest Verson), to achieve earth resistance less than one Ohm including constructin of masonary enclosure with hinged cover plate of cast iron with locking arrangement on top watering pipe connection from earth plate to top with 50mm dia x 3000 mm GI pipe class B as per drawing and provision of earth plate. | — | — | — | 39,854.64 | |
| — | 400.00 | — | — | ||
| Supply & Erection of GI strip of size 25mmx3mm as per IS 3043/1987 (Latest Version) 300 mm deep, in ground/recessing in floor clamping in trenches of sub station by grouting clamps for earthing of body of package type Sub station as per drawing approved by Railways. | — | — | — | 64,372 | |
| — | 100.00 | — | — | ||
| Supply and fixing of 100 mm dia GI pipe class 'B' IS:1239 Pt I latest with all fixing accessories. | — | — | — | 38,524 | |
| — | 163.00 | — | — | ||
| Supply and fixing of 63 mm dia. GI pipe class 'B' IS:1239 Pt I latest with all fixing accessories . | — | — | — | 43,221.08 | |
| — | 2050.00 | — | — | ||
| Supply and fixing of 50 mm dia GI pipe class 'B' IS:1239 Pt I latest with all fixing accessories. | — | — | — | 3,79,475.5 | |
| — | 20.00 | — | — | ||
| Concrete for foundation for pump LT panel, cable trench etc in ratio 1:3:6. | — | — | — | 59,553.6 | |
| — | 2.00 | — | — | ||
| Supply and fixing of following safety items as per IE rules ms in sub-station Fire extinguisher complete with all other accessories (04 Nos.) Rubber mat (ISI marked) non stick type suitable for 11KV AC supply of size 3600x1000x25 mm (04 Nos.) Electric shock treatment chart in Hindi (06 Nos.), 11000 volts/415 volt danger notice plate complete (08 Nos.) Schematic diagrame of HT/LT installations on white hylum sheet complete (04 Job). | — | — | — | 11,707.26 | |
| — | 4.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of 11 KV 200 A triple pole gang operated GO switch with DO fuse & operating rod. | — | — | — | 85,753.12 | |
| — | 2.00 | — | — | ||
| Transportation, cutting, foundation, Erection of DP structure with poles 11/13 m long, 11 KV pintype, disc type porcelain insulators, dangerboard, anti climbing device, MS channel 100x50x4.7 mm, MS flat 50x6mm, MS angle 50x50 x6 mm complete including, painting & muffing of rail poles. (Note:-Scrap rail poles/steel tubular poles will be supplied by the Railway in designated stores:) | — | — | — | 20,090.78 | |
| — | 12.00 | — | — | ||
| Supply & erectrion of V type HT cross arm channel of size 100x50x4.07 mm, MS flat of size 50x6 mm MS angle 75x75x6 mm not less than 1525 mm long with 11 KV pin/disc type porcelain insulator (3 Nos.) including MS nut bolt, washers & one coat of red oxide primer & two coats of aluminium paints. | — | — | — | 17,901.12 | |
| — | 146.00 | — | — | ||
| Supply & Erection of stay set to poles complete its CC foundation in ratio 1:3:6 stay rod, stay tightner, stay insulator, stay GI wire7/8 SWG thimble & other fixing accessories as required | — | — | — | 1,29,411.48 | |
| — | 3.00 | — | — | ||
| Erection of swaged type steel tubular LT poles 10 mtr long, including cutting as per the direction given by site engineer with CC foundation muffing , plastering & painting of one coat of red oxide primer &two coats of al, paint then black paint up to 6 feet height from bottom. | — | — | — | 6,971.07 | |
| — | 700.00 | — | — | ||
| Supply of materials & painting of railway's supply steel tubular poles with 2 coats of red oxide primer and then 2 coats of aluminium paint and then black paint at bottom as per railway standard | — | — | — | 3,54,886 | |
| — | 7.00 | — | — | ||
| Supply and Erection of cross arm channel of size 75x40x4.4 mm MS flat of size-40x6 mm, suitable for tublar poles/rail poles with MS nuts, bolts, washers, pins and shackle type porcelain insulators (06 Nos.) MS angles of size-50x50x6 mm not less than 900 mm long for quarding. | — | — | — | 3,268.72 | |
| — | 1.00 | — | — | ||
| Shifting of MDB- dismantling, re-Erection & Commissioning of LT MDB at new location including brick work of suitable size and ht from ground | — | — | — | 6,504.03 | |
| — | 10.00 | — | — | ||
| Supply, Installation/ connection along with Testing and commissioning of watercooler Capacity-150 Lt including earthing. | — | — | — | 3,85,222 | |
| — | 100.00 | — | — | ||
| Excavation of cable trench 1000 mm deep and back filling in all type of soil under the track/road for laying of the cable including the work of supply and placing of RCC Hume pipe 150 mm dia with necessary RCC collers, etc for drawing the cable in trench under the track/road. | — | — | — | 16,844 | |
| — | 2.00 | — | — | ||
| "Supply, Erection Commissioning of LT control panel cubical floor mounted type dust and vermin proof multitier construction we ither proof copper ventilation arrangement outdoor type LT distribution board for operation on 3 phase 4wire 415V Ad supply system recondition with 14 SWG MS sheet base MS angle 50x50x6 mm MS channel 75x40x6 mm. It shall be coated with 2 coats approved colour. The LT panel shall be of front operated with copper conductor cable, cable glands, earthing studs, feeder, name plate and danger board on front. The LT panel shall be erected on the floor. The panel shall comprises of 400 Amps bus bar with protection equipment, 01 Number incoming ide 250A MC 50KA, 4X100 A MCCB 36 CA, 2X63A MCCB 30KA and 05 Nos. 32A MCCB 30KA. All MCCB should be 4 pole type voltmeter, Ammeter indicating lamp: shall be fitted all incoming and outgoing s de complete with locking arrangement and all other required accessories as per site" | — | — | — | 1,39,604.84 | |
| — | 2.00 | — | — | ||
| "Erection Commissioning of LT control panel cubical floor mounted type dust and vermin proof multitier construction we ither proof copper ventilation arrangement outdoor type LT distribution board for operation on 3 phase 4wire 415V Ad supply system recondition with 14 SWG MS sheet base MS angle 50x50x6 mm MS channel 75x40x6 mm. It shall be coated with 2 coats approved colour. The LT panel shall be of front operated with copper conductor cable, cable glands, earthing studs, feeder, name plate and danger board on front. The LT panel shall be erected on the floor. The panel shall comprises of 400 Amps bus bar with protection equipment, 01 Number incoming ide 250A MC 50KA, 4X100 A MCCB 36 CA, 2X63A MCCB 30KA and 05 Nos. 32A MCCB 30KA. All MCCB should be 4 pole type voltmeter, Ammeter indicating lamp: shall be fitted all incoming and outgoing s de complete with locking arrangement and all other required accessories as per site" | — | — | — | 41,881.46 | |
| — | 2.00 | — | — | ||
| Erection & Testing & Commissioning of 7.5 KVA sinewave inverter , single phase input supply one phase 3 wire out put voltage 220 V + with 10 No. battery 12 V 150 AH complete with all accessories and wiring | — | — | — | 1,17,572.86 | |
| — | 80.00 | — | — | ||
| Supply of musical bell -Ding Dong including Erection, Testing and Commissioning. | — | — | — | 11,874.4 | |
| — | 480.00 | — | — | ||
| Supply and fixing of 2x4 sqmm PVC insulated copper wire single core 1100 v grade as per is: 694 (latest) for sub mains with PVC conduit pipe heavy duty not less than 25 mm dia in recessed /surface of the wall with earth continuity PVC copper wire including, Erection Testing and Commissioning. | — | — | — | 38,424 | |
| — | 250.00 | — | — | ||
| Supply, Erection, Testing & Commissioning of guard wire of 2x8 SWG GI wire of guarding with lacing at the intervals of not more than 2.0 meters. | — | — | — | 5,627.5 | |
| — | 430.00 | — | — | ||
| Supply, Erection Testing & Commissioning of service tapping of 2x10 sq. mm PVC insulated sheathed Alu, conductor multistrands with 8 SWG GI wire supporting were porcelain insulator at a distance of meter including MS clamps to be fixed at service pole with all other required accessories as per site. | — | — | — | 87,487.8 | |
| — | 37.00 | — | — | ||
| Supply, & fixing of swan neck type service pipe bracket of GI pipe B class 3mtr long 50mm dia complete with all fixing accessories required at site | — | — | — | 23,139.43 | |
| — | 10.00 | — | — | ||
| Supply, Erection Testing & Commissioning of stationary storage type electric water heater closed / vented type vertical material of the inner container copper, capacity 25 Ltr, watt 1500 | — | — | — | 35,813.9 | |
| — | 1.00 | — | — | ||
| Supply , Erection, Testing ,and Commissioning of electrically driven submersible pump set water lubricated, 3 phase 415 V ,50Hz AC induction motor cap upto 7.5 HP in bore well 150 mm/200 mm dia. ,with all accessories. | — | — | — | 79,100.85 | |
| — | 16.00 | — | — | ||
| Supply, Fixing & Commissioning of 6 Way Metal Clad SDB with 1x40 Amp, MCB DP isolator, 2x16 Amps MCB SP, 2x6 amp MCB SP fitted on suitable PVC board complete with all required material as per site. | — | — | — | 21,216.16 | |
| — | 650.00 | — | — | ||
| Horizontal Boring of Cable Duct at 1.4 to 2.1 meter depth from the bottom of sleeper and laying of 150mm dia DWC Pipe/200 mm HDPE pipe. The work shall be done as per extant practice and instruction of site supervisor. It includes supply of DWC/HDPE pipe confirming to IS: 14930, Part -II, of 2001 or latest version.(In Rock Soil). | — | — | — | 42,57,467.5 | |
| — | 1350.00 | — | — | ||
| Horizontal Boring of Cable Duct at 1.4 to 2.1 meter depth from the bottom of sleeper and laying of 150mm dia DWC Pipe/200 mm HDPE pipe. The work shall be done as per extant practice and instruction of site super visor. It includes supply of DWC/HDPE pipe confirming to IS: 14930, Part -II, of 2001 or latest version. (In Normal Soil) | — | — | — | 18,21,082.5 | |
| — | 850.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of Sub Main of 2x6 Sq.mm PVC insulated sheathed copper wire, multi strands, 1100 volts grade, continues PVC insulated sheathed copper earth wire of 1.5 sq mm, through PVC heavy duty conduit pipe/PVC Channel complete with all other accessories required as per site and removal of existing wiring of sub main if required. ( Also inclusive Removal of existing submain if required ) | — | — | — | 71,604 | |
| — | 55.00 | — | — | ||
| "Supply, Erection, Testing and Commissioning of 15 Amps. Power Socket (Metal Clad for AC ) complete with wiring materials 04 Sq. MM, PVC insulated, multi strands FRLS copper wire 1.5 sq. mm. PVC insulated copper multi strands continue earth wire by PVC pipe concealed /open wiring (as per site requirement) . Power socket with switch 16/20/25 Amps MCB SP complete with all other accessories required as per site". | — | — | — | 40,262.2 | |
| — | 45.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of Maintenance Free Earthing kit consisting of earth electrode copper bonded of 1800 mm, long,17.2 mm dia and copper bonding .Thickness of 250 microns (2 Nos) thread less compressed type coupler, earth enhancing compound , copper tape 25x 6 x 300 mm (02 nos) and 25x6x150 mm terminate on earth electrode and cadmium bronze cable/copper cable of 3/16" to connect bus bar 10 Mtr. each earth complete with digging of earth Jointing of electrode etc. | — | — | — | 4,96,693.8 | |
| — | 30000.00 | — | — | ||
| Excavation of cable trench in soft morrum, plain ground, concrete/ pucca surface etc. and back filling of cable trench for laying of HT/LT cables including placing of bricks in cross position in the trench, cable maker etc.(as per IE rule) | — | — | — | 9,46,800 | |
| — | 45000.00 | — | — | ||
| Laying/Cleating of Rly. Supply XLPE/PVC insulated LT under ground, Aluminium conductor, armoured/unarmoured, cable 1.1kv grade including connecting, Testing and energising (Note: LT cable will supplied by the Rly. as per IE rules) | — | — | — | 6,30,450 | |
| — | 20.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of (36 - 42) Watt, 2'x2' LED Panel Light & Fittings complete with required connecting wire and all other fixing accessories required as per site. | — | — | — | 60,240 | |
| — | 85.00 | — | — | ||
| Erection, Testing and Commissioning of Energy efficient BLDC Fan, 1200 MM Sweep, 25 - 32 Wattage Capacity, Single Phase 230 V, 50 Hz AC with electronic regulator & all fixing accessories. Celling fan to be connect from the ceiling roses through PVC flexible pipe by 1.5 sq.mm wire | — | — | — | 58,320.2 | |
| — | 35.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of Wall Mounted Type Bracket Fan, Single Phase, 230 Volt, AC 400 MM Sweep complete with all other accessories as per site requirement. | — | — | — | 42,048.3 | |
| — | 31.00 | — | — | ||
| Supply of 1.5 Ton 3-Star 230 V 50 Hz. 1-Phase Split AC Unit with Copper Condenser, Rotary Compressor, wireless LCD Remote design to work in ambient temperature upto 520 C & connecting kit including Copper pipe - 10 Feet, Drain pipe - 10 feet, Cable wire - 10 feet, ODU stand - 01 No. with eco-friendly refrigerant-R410A / R32A etc. | — | — | — | 11,22,048.1 | |
| — | 31.00 | — | — | ||
| Fixing and connecting Split AC 1.5 Ton with 10 feet (3 Mtr.) extra connecting kit (Copper Pipe, Drain Pipe) and wall excavation and filling with POP in all respect required as per site. | — | — | — | 1,17,683.75 | |
| — | 25.00 | — | — | ||
| Installation of 04 KVA Voltage Stabilizer Wall mounted type, I/P Voltage - 170 to 280 V, O/P Voltage - 220 V + 10% ISI mark. | — | — | — | 22,664 | |
| — | 35.00 | — | — | ||
| Supply and Installation of 2.0 Ton Inverter AC (Variable Speed) Input Power Supply 230 V AC (+/- 10 %), 50 Hz, AC , Copper Coil Material for Condenser & Evaporator with eco friendly Refrigerant Type R-32. | — | — | — | 16,39,186.5 | |
| — | 150.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of Octagonal Pole High Tensile Steel as per IS standards conforming to grade S355JO or equivalent 5 Meter long complete with pit foundation with 1:2:4 concrete for the Octagonal pole 1 meter ±10% depth with all materials and double arm bracket including connection. | — | — | — | 15,27,399 | |
| — | 150.00 | — | — | ||
| Dismantling of Exiting Pole Rail Pole / Tubular Pole and Handing over the Material to consignee depot. | — | — | — | 59,958 | |
| — | 2.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of 1.5 HP, Single Phase, 230V, Out let size - [25 -32 MM submersible Pump Set water lubricated type, (Discharge-20 to 50 LPM, Head- 90 to 110 Mtrs) suitable as per site complete with all other accessories- Reducer, clamps etc. along with Provision of threading & Sockets required of Industrial Type . | — | — | — | 26,736.76 | |
| — | 380.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of 2.5 Sq.mm, Water proof, Flat Submersible Copper Cable suitable for above Pump. | — | — | — | 34,998 | |
| — | 2.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of Submersible Pump Set Controller with MU-2P Type Single Phase DOL Starter ( Relay range 9-14A ) | — | — | — | 28,514.78 | |
| — | 18000.00 | — | — | ||
| Erection, Testing and Commissioning of LT XLPE insulated Aerial Bunched cable ( ABC) of size ( 3x120 + 1x95 + 1x16) Sq mm with bare messenger wire as per IS: 14255-1955 or latest . | — | — | — | 21,12,480 | |
| — | 844.00 | — | — | ||
| Erection, Testing and Commissioning of I-Hook with other accessories required as per site. | — | — | — | 27,379.36 | |
| — | 975.00 | — | — | ||
| Erection, Testing and Commissioning of Dead ended clamp and other accessories required as per site. | — | — | — | 1,26,984 | |
| — | 844.00 | — | — | ||
| Erection, Testing and Commissioning of Suspension clamp and other accessories required as per site. | — | — | — | 95,439.52 | |
| — | 2500.00 | — | — | ||
| Erection, Testing and Commissioning of Piercing connector 90/120 sq mm and other accessories required as per site | — | — | — | 14,62,150 | |
| — | 520.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of Distribution Box with accessories and other accessories required as per site. | — | — | — | 4,99,090.8 | |
| — | 850.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of LT Shackle Insulator with nut and bolt and other accessories required as per site. | — | — | — | 49,699.5 | |
| — | 500.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of Shackle Strip 12 inch with other accessories required as per site. | — | — | — | 53,565 | |
| — | 15.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of 225 mm Sweep Exhaust Fan suitable on 230 volt AC, single phase complete with all other accessories required as per site. | — | — | — | 19,570.05 | |
| — | 30.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of Digital Two AC Timer for Window / Split Type AC for 2.0 TR each [Digital Display LCD MODEL] LCD Model latest intelligent micro controller based technology [2AC TIMER] program 1 hr to 24 hrs. with 30 Amps heavy duty 2 relay out put for two AC auto / manual facility for THREE PHASE HI WALL OR CASSETE TYPE OR DUCTABLE TYPE ,AC Dynamic / saitech system / Om energy savers / BELL Nutronics make, | — | — | — | 1,55,171.7 | |
| — | 10.00 | — | — | ||
| Supply, Erection, Testing and Commissioning of 16 Meter Long High Mast System with its accessories duly hot dip galvanised and suitable for wind velocity as per IS 875 -Part-3 or latest version , it shall also included 03 points suspension head of steel frame with 06 mm dia steel wire rope, double drum with galvanised lantern carriage arrangement suitable for 06 nos luminaries symmetrically and its control gear boxes, The mast shall have an optional arrangement for external power for its operation ie lowering and raising system . supply of foundation bolt, manufactured from special steel along with nut, bolt, washer, anchor plate, and templates, , supply and installation of control panel boards consisting with 40 Amps , four pole MCB, forward and reverse contractor for lowering and lifting astronomical timer and suitable control circuit [with required cable /wire] for the operation of the high mast. design and casting of suitable shallow foundation with M-20 Concrete for the HIGH MAST considering safe soil bearing capacity at site as 10T/SO Meter at 02 meters depth with cement concrete ratio 1.3.6 complete with 06 nos 250 watt LED Beam light and fitting outdoor type should be IP-65-66 Complete with 02 nos pipe earthings arrangement required as per site complete with all other accessories as per site requirement, | — | — | — | 24,04,069 | |
| — | 40.00 | — | — | ||
| Supply ,Erection,Testing and Commissioning of 15 W LED Solar street light system with 6/7 m pole G.I. complete, The control grear shall include features for aotomatic swiching ON & OFF of street light according to day light including inbuilt battery, battery shall have at least 3 days backup to cater for cloudy days. Battery shall be maintenance free, with all accessories as per site requirement. | — | — | — | 23,10,213.2 | |
| — | 12.00 | — | — | ||
| Hiring of One Non-AC Multi -Utility 4 Wheeler Motor Vehicle Innova, Xylo and Scorpio or Similar is in Working Condition with Driver, Fuel , Crew & Maintenance etc with toll tax (2000 Km per Month) | — | — | — | 3,75,794.64 | |
| — | 20.00 | — | — | ||
| Supply, Erection,Testing and Commissioning of Solar emegency Indoor light 07 Watt, efficiency>80%, CRI>70, CCT-6500 K, Luminous efficiency>130 Lm/w , inbuilt battery 12AH, Battery Type - Li-ferric phosphate. | — | — | — | 1,54,181.8 | |
| — | 20.00 | — | — | ||
| Supply , Erection, Testing and Commissioning of solar panel (module) 50 Watt (Poly crystalline), Panel voltage-21 V with all accessories for fitment of Solar panel as per site requirement | — | — | — | 1,42,250 | |
| — | 480.00 | — | — | ||
| Excavation of cable trench Track crossing and Laying of 120 mm Outer dia HDPE Pipe at the safe depth below the Track Sleeper as per Railway Standard. The work shall be done as per extent practice and instruction of site Engineer. It includes supply of HDPE pipe confirming to IS:14930 (Part-II of 2001) REX-Poly Exprusion or similar make for normal soil. | — | — | — | 6,51,388.8 | |
| — | 3480.00 | — | — | ||
| Laying, connecting Testing and Commissioning of 4 core 16-95 sq.mm LT PVC insulated aluminium armoured cables. (Under RCC, PCC, Dumer Platform/Road) (NOTE-Cable will be supplied by Railway). | — | — | — | 15,91,264.8 | |
| — | 32.00 | — | — | ||
| "Recessing of Meter cum distribution box fabricated with 14 SWG MS sheet in two compartments, one for Meter and other for MCB's powder coated with approved colour thickness not less than 60 micron, approximate size 500x300x135 mm deep, suitable for operation on single phase 230 Volts AC supply system complete with internal connections with PVC insulated copper conductor cable 6 sq.mm/ 10 sq.mm as required, earthing connections,Testing & Commissioning etc. as per IS:8623/Pt.I/1993 latest version for manufacturing of assembly IS 1897/1993 & 8080/1976 for copper bus bar, IS 8828/93 for MCB's IS 13779/93 (latest version) for electronic energy meter. (a) MCB SPN 20 Amp C series (01 Nos) for incoming & for outgoing MCB SP 10/16A C series 02 nos & MCB C series 6 A 04Nos, single phase 10-20 A KWh meter digital type with 6 mm thick Backelite sheet on base with all inter connections (For Type-II & Type-III Qrs) (Erection Only)" | — | — | — | 63,909.44 | |
| — | 15.00 | — | — | ||
| "Supply and Recessing of Meter cum distribution box fabricated with 14 SWG MS sheet in two compartments, one for Meter and other for MCB's powder coated with approved colour thickness not less than 60 micron, approximate size 500x300x135 mm deep, suitable for operation on single phase 230 Volts AC supply system complete with internal connections with PVC insulated copper conductor cable 6 sq.mm/ 10 sq.mm as required, earthing connections,Testing & Commissioning etc. as per IS:8623/Pt.I/1993 latest version for manufacturing of assembly IS 1897/1993 & 8080/1976 for copper bus bar, IS 8828/93 for MCB's IS 13779/93 (latest version) for electronic energy meter. (b) MCB SPN 40 A C series (01 Nos) MCB SP 20 A C series 2 nos for incoming & for outgoing MCB 10A C seris 03 nos & MCB C series 6 A 03Nos, single phase 20-40 A KWh meter digital type with 6 mm thick Backelite sheet on base with all inter connections (For Type- IV & Type-V Qrs)" | — | — | — | 1,17,748.2 | |
| — | 1400.00 | — | — | ||
| Erection Testing and Commissioning of energy efficient LED Lamp fitting , power coated CRCA MS housing, 4' long 1X20 watt completed with all accessories, Make- Havells - LHFYBYPNIA1W022 (Box) with LED tube model No, LHLDCLXEUL83020 (tube ) with all accessories or similar, | — | — | — | 4,53,880 |
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .