COMPOSITE WORKS FOR COMPLETION OF BALANCE JOBS ON SINGLE POINT RESPONSIBILITY BASIS AT GMPL

Amount

Total of BOQ 2

Total of BOQ 3

Total of BOQ 4

Total of BOQ 5

Total of BOQ 6

Total of BOQ 7

Total of BOQ 8

Total of BOQ 9

Description of Work / Item(s)

Amount

GENERAL NOTES

CONTRACTOR shall ensure that the rates quoted for execution of electrical works take into account all requirements, services, activities & responsibilities defined as forming part of CONTRACTOR’s scope in the Tender Document / Contract. Special attention shall be given to include the efforts necessary to implement & comply with the relevant safety practices to be followed for the electrical works at the Plant Site, as per the applicable HSE documents.

EQUIPMENT:

INSTALATION OF TRANSFORMER -

Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of assemblies / sub-assemblies, assembling and installation components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, filtration of oil, touch up painting, stenciling with paint on equipment enclosures as required and other associated work to ensure the completeness of installation work Testing and pre-commissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as chipping, grouting for fixing of associated equipment / assemblies and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. Fabrication and installation of steel support structure /stopper wheel/ supporting frames for various equipment / assemblies / sub-assemblies as per the site requirement Supply of all fixing hardware as per the site requirement is included in the scope.

DISTRIBUTION TRANSFORMER

800KVA 6.6KV/0.433KV DYn11 Oil immersed Copper Wound Transformer (ONAN) with Off circuit tap links of range +5% to -5% @2.5. Class of Insulation - F, Temp.Rise - 70 Deg.C, Impedance: 6.25% (With IS Tol.) Oil capacity : As per Vendor documents Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per vendor documents

LIGHTING TRANSFORMER

250 KVA, 415V/433V, Z=4%, dry type, 50 Hz, Dyn11, Indoor type, Lighting distribution transformer with off-circuit tap changer

INSTALATION OF BUSDUCTS -

Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of assemblies / sub-assemblies, assembling and installation components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, touch up painting, stenciling with paint on equipment enclosures as required and other associated work to ensure the completeness of installation work, connection of busduct with both end. Testing and pre-commissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as modifications in the wall cutout, as required, for making busduct wall opening suitable for busduct entry etc., replastering and making area good as per the site requirement (including the supply of consumable material for the same), sealing with fire proofing compound, is included in the scope. Fabrication and installation of steel support structure / supporting frames for various equipment / assemblies / sub-assemblies as per the site requirement Supply of all fixing hardware as per the site requirement is included in the scope.

Distribution Transformer Bus Duct-1 Rating : 415 V, 1250 A Construction : Mild Steel enclosure, Sandwich Type, Al Busbars From : Transformer SS4-TR-01A To :SS4-EPMCC-01 Approx. length : 10 meters (Indoor) + 10 meters (Outdoor) Approx. Weight : As per vendor documents

Distribution Transformer Bus Duct-2 Rating : 415 V, 1250 A Construction : Mild Steel enclosure, Sandwich Type, Al Busbars From : Transformer SS4-TR-02A To :SS4-EPMCC-01 Approx. length : 10 meters (Indoor) + 10 meters (Outdoor) Approx. Weight : As per vendor documents

INSTALATION OF HV/MV/LV ELECTRICAL PANELS -

Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of various shipping sections / assemblies, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, interpanel wiring, stenciling with paint on equipment enclosures as required, including supply of all wiring materials, drilling of gland plates for cable gland fixing, plugging of unused cable entries etc. and other associated work so as to ensure the completeness of installation work. Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Installation on cable celler floor cutouts/foundation/cable trenches or fixing to wall or steel structures, aligning,leveling, welding, bolting, grouting, including minor civil work like chipping, cutting, refilling and sealing of pockets in wall/floor etc. Any modification/alteration to be carried out in individual shipping section for proper alignment & matching with other sections etc.Supply of grouting materials, foundation bolts if not supplied with equipment, pluges for unused cable entries, hardware materials, touch up painting as required, wiring material & copper lugs for wiring.Complete with labour & materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

INSTALLATION OF HT SWITCHGEAR : 6.6 KV ICOG PANELS (ICOG-01 & ICOG-02)

Rating : 6.6 kV, 630 A, 21kA, 1 Sec, Al Busbars Construction : Floor mounting, single front Nos. of vertical sections : 1Nos. Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor docs Mounting : On floor

INSTALLATION OF LV SWITCHBOARDS: 415 VOLT, TAG NO. SS4-EPMCC-01

Rating : 415V, 1250A, 35 kA, 1 Sec, Al Busbar Approx. Dimensions (LxBxH) : As per Vendor docs Construction : Floor mounting, Double front except incomer panel, bus coupler, ACB outgoing feeders Approx. maximum DimensiSons (LxBxH) : As per Vendor docs Approx. maximum Weight : Weight of the unit from 3001 upto 4500 kg. Mounting : On floor, As per Equipment layout

LIGHTING PANELS/ POWER PANELS/ LCS

63 A, 4 pole incomer MCB isolator and ELCB and 12 Nos. outgoing double pole MCBs (upto 20 A), Ex-d type suitable for gas group IIA/IIB, temperature class - T3.

Power socket DB: 125 A, 4 pole incomer MCCB isolator and ELCB and 6 Nos. outgoing 4 pole MCBs (upto 63 A), Ex-d type suitable for gas group IIA/IIB, temperature class - T3.

Power socket DB: 63 A, 4 pole incomer MCCB isolator and ELCB and 6 Nos. outgoing 4 pole MCBs (upto 20 A), Ex-d type suitable for gas group IIA/IIB, temperature class - T3.

400 A, 415Volt, 10KA fro 1 Sec, 4 pole incomer MCCB isolator and 20 Nos. outgoing 63 A, MCB with ELCB, Industrial type, IP-55 (min)

63 A, 4 pole incomer MCB isolator and ELCB and 12 Nos. outgoing double pole MCBs (upto 20 A), Industrial Type type suitable for Safe Area

63 A, 4 pole incomer MCB isolator and ELCB and 04 Nos. outgoing double pole MCBs (upto 20 A), Industrial Type type suitable for Safe Area

Supply, installation, connection, testing and commissioning of safe area UPS / power panels, surface / flush mounted type, wall mounted type in dust tight ( with hinged cover) sheet steel enclosure having 4 pole incomer and single pole MCB (9 kA type) for outgoing circuit control with complete wiring, including cable termination, all necessary hardware, connection and fixing of cable glands, lugs, and consumables like anchor fastners/studs etc required for the complete installation including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge. Also any assistance required to Client for CEA approval shall be in Contractor's scope. The panels shall be supplied along with requisite number of suitable cable glands required for incoming and outgoing cables and plug for plugging unused entry.

UPS Distribution Board - 125A , 110 V AC, 10 KA for 1 sec. Industrial type, IP-55 (min)

MOV Distribution Board - 250 A , 415 V, 3Ph, 65 KA for 1 sec. Industrial type, IP-55 (min)

Power Distribution Boards - 415 V AC, 3Ph, 10 KA for 1 sec. Industrial type, IP-55 (min)

DC Distribution panel - 63A, 110 V, 10 KA for 1 sec. Industrial type, IP-55 (min, with O RING Diode circuit)

Supply, installation, connection, testing and commissioning of safe area lighting panels & Critical Lighting Panels, surface / flush mounted type, wall mounted type in dust tight ( with hinged cover) sheet steel enclosure having 4 pole incomer and single pole MCB (9 kA type) for outgoing circuit control with complete wiring, including cable termination, all necessary hardware, connection and fixing of cable glands, lugs, and consumables like anchor fastners/studs etc required for the complete installation including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge. Also any assistance required to Client for CEA approval shall be in Contractor's scope.The panels shall be supplied along with requisite number of suitable cable glands required for incoming and outgoing cables and plug for plugging unused entry.

Lighting Distribution Board - 63 A , 415 V, 10 KA for 1 sec. Industrial type, IP-55 (min) Incomer: 63 A, 4Pole, MCB Outgoing: 12 Nos., 16A, 4MCB and ELCB (100mA)

Lighting Distribution Board - 63 A , 415 V, 10 KA for 1 sec. Industrial type, IP-55 (min) Incomer: 63 A, 4Pole, MCB and ELCB (100mA) Outgoing: 12 Nos., 20A, DP MCB

Small Power panels (Normal) - 63 A , 415 V, 10 KA for 1 sec. Industrial type, IP-55 (min) Incomer: 1 no, 63 A, 4Pole, MCB Outgoing: 6 Nos., 20A, DP MCB and ELCB (30mA)

Power panels for 3Ph socket - 125 A , 415 V, 10 KA for 1 sec. Industrial type, IP-55 (min) Incomer: 1 no, 125 A, 4Pole, MCB Outgoing: 4 Nos., 63A, FP MCB and ELCB (30mA)

Supply & Installation of Industrial type hoseproof & weatherproof local control stations in CRCA sheet steel enclosure along with suitable rain protection hood of following types as per enclosed specifications, standards, specification sheets, etc. of Technical Specification.

Type – 5 (Emergency Stop Push Button + 2 Nos. Indication Lamps) & locakable in OFF position for Transformers.

SUPPLY & INSTALLATION OF ELECTRIC SIREN

Supply and Installation connection, testing and commissioning of industrial heavy duty siren (Electric) compliance with OISD-177 and ERDMP standards. It offers automated and manual siren activation across various emergency levels, including drills and critical situations. Seamlessly integrating with systems like fire panels, PLCs, DCS, and SCADA, it allows remote operation without manual intervention. Features include a microcontroller for precise control, an intuitive LCD display, and a durable, fire-red, IP-55 rated enclosure. Customizable to match specific siren specifications, it enhances safety and emergency response. The complete wiring, including cable termination, all necessary hardware, connection and fixing of cable glands, lugs, and consumables like anchor fastners/studs etc required for the complete installation including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge. The panels shall be supplied along with requisite number of suitable cable glands required for incoming and outgoing cables and plug for plugging unused entry. Integration with Firalarm & Gas detection system as per the Operation philosophy. a. Control panel of I/P supply of 3 phase 415±10% Volt, 50Hz. With Automatic / manual operating mode, 5 No.s of program with internal LCD display of 16*2, vertical wall mounted, IP56 enclosure type with protection of under voltage, over voltage, single phasing protection. Quantity: 01 b. Motor of rated power min. 2HP, 2800 RPM, with IP 55 protection of IE2 motor type. with ideal audible renge of min. 5KM. Quantity: 02 c. Local Push button IP-55 and ON/OFF trip manual switch,etc Quantity: 02 To refer the Siren data sheet "215498C-0000-SP-1566-008"

INSTALLATION OF AC UPS AND BATTERY

Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of equipment / assemblies, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work to ensure the completeness of installation work. Assembly of battery rack, placement of battery cells on the support rack, electrolyte filling and associated work as recommended by MANUFACTURER is included in the scope. Installation of battery MCCB with enclosure at the location indicated in the applicable layouts is included in the scope. Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as chipping, grouting for fixing of equipment / assemblies and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. Fabrication and installation of steel support structure / supporting frames for various equipment / assemblies as per the site requirement. Supply of all fixing hardware as per the site requirement is included in the scope.

415 VAC, 80 kVA, 3 phase, 50 Hz., Parallel redundant with bypass AC UPS system for (QC Laboratory) including Battery banks for 30min. backup with floor mounted, fixed type, compartmentalized AC distribution board. Rating : 415 VAC, 80 kVA, UPS with bypass Construction : Non Compartmentalized, Single front Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor Docs Mounting : On False floor supported with structural steel base frame Battery bank (2X50%) Battery type : Ni-Cd Nos. of cells : As per Vendor docs Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor docs Mounting : On False floor supported with structural steel base frame ACDB Construction : Compartmentalized, Single / Double front Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor docs Mounting : Floor

415 VAC, 40 kVA, 3 phase, 50 Hz., Parallel redundant with bypass AC UPS system (Tag: SS4-UPS-01 for SS4 & Training center) including Battery banks for 30min. backup with floor mounted, fixed type, compartmentalized AC distribution board. Rating : 415 VAC, 40 kVA, UPS with bypass Construction : Non Compartmentalized, Single front Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor Docs Mounting : On False floor supported with structural steel base frame Battery bank (2X100%) Battery type : Ni-Cd Nos. of cells : As per Vendor docs Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor docs Mounting : On False floor supported with structural steel base frame ACDB Construction : Compartmentalized, Single / Double front Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor docs Mounting : Floor

240 VAC, 15 kVA, 1 phase, 50 Hz., Non-redundant with bypass AC UPS system (Tag: SS4-UPS-01 for SS4 Safety Lighting) including Battery banks for 30min. backup with floor mounted, fixed type, compartmentalized AC distribution board. Rating : 240 VAC, 15 kVA, UPS with bypass Construction : Non Compartmentalized, Single front Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor Docs Mounting : On False floor supported with structural steel base frame Battery bank (2X100%) Battery type : Ni-Cd Nos. of cells : As per Vendor docs Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor docs Mounting : On False floor supported with structural steel base frame ACDB Construction : Compartmentalized, Single / Double front Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor docs Mounting : Floor

240 VAC, 5 kVA, 1 phase, 50 Hz., Non-redundant with bypass AC UPS system for DM PLC room. Rating : 240 VAC, 5 kVA, UPS with bypass Construction : Non Compartmentalized, Single front Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor Docs Mounting : On False floor supported with structural steel base frame Battery bank (1X100%) Battery type : Ni-Cd Nos. of cells : As per Vendor docs Approx. Dimensions (LxBxH) : As per Vendor docs Approx. Weight : As per Vendor docs Mounting : On False floor supported with structural steel base frame

INSTALLATION OF DC UPS AND BATTERY

Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of equipment / assemblies, assembling and installation of components / devices supplied separately - as recommended by MANUFACTURER / applicable construction documents, stenciling with paint on equipment enclosures as required and other associated work to ensure the completeness of installation work. Assembly of battery rack, placement of battery cells on the support rack, electrolyte filling and associated work as recommended by MANUFACTURER is included in the scope. Installation of battery MCCB with enclosure at the location indicated in the applicable layouts is included in the scope. Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as chipping, grouting for fixing of equipment / assemblies and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. Fabrication and installation of steel support structure / supporting frames for various equipment / assemblies as per the site requirement. Supply of all fixing hardware as per the site requirement is included in the scope.

110 VDC Nickel Cadmium battery bank for 30min back-up with 2Nos. Float cum Boost charger with integral compartmentalized free standing fixed type DC distribution board (DCDB) (Battery Tag: SS4-BS-03 & DCDB + Charger Tag. No.-SS4-DCP-01 for Substation-4) as per Battery Specification (0814-B000-JSS-1673-002) and Battery Charger Specification (0814-B000- JSS-1673-001).

CABLE / WIRE LAYING, TERMINATION AND CABLE ROUTING SYSTEMS

CABLE LAYING, TESTING & COMMISSIONING

Laying (using cable pulling by motorized winch with torque limits) ,Testing & Commissioning of HV/MV/LV Power, Control & FO Cables. Horizontal & vertical laying of cables of different voltage grade and types in ready trench/trays/Racks, underground, supported on structures, pull through pipe sleeves, clamping to column wall or structure using GI spacers and saddles (at an interval of 300 mm), Installation & supply of anodize Aluminum / Stainless steel / lead strip number tags for certified trefoil clamps of non‐magnetic material for 1C cables, overhead & buried cables respectively. Installation & supply of G.I saddles, saddle bars & GI Clamps, clamping of cables on trays & necessary hardware's. Cables laid in trays shall be dressed and clamped using GI Clamps at every 750 mm. Scope shall include opening the RCC slabs/Covers from Cable Trenches before laying and replacing them after laying. The motorized winch required for cable pulling shall be arrange by contractor and no separate payment for the same will be made. The cable laying work shall include transportation of cable drums from owner's issue point to the place of installation by contractor's own lifting & transportation arrangement, unpacking, cable cutting as per actual length measurement & cable schedule/cable drum schedule, return of unused cable/drums to the owner's store & removal of empty drum to Owner's Scrap Yard, including all labour and materials, complete as per approved drawings, specifications of this tender and directions of Engineer‐in‐charge. Contractor shall provide necessary assistance for CEA approval, if required. Note: Contractor shall submit re‐compilation report after installation/laying of all cables 6.6kV/1.1kV Grade Al conductor, Armored, XLPE insulated, FRLS of HV/LV Power, Control/PA/Telephone cables.

Cables with OD upto 20 mm. (including pair & FO cable)

Cables with OD above 20 mm but upto 30 mm

Cables with OD above 30 mm but upto 40 mm

Cables with OD above 40 mm but upto 55mm

Cables with OD above 60 mm but upto 80 mm (for 6.6 KV cable)

SUPPLY OF 6.6 kV HV POWER CABLE END TERMINATIONS KIT

3 Core cables 6.6 kV , 400 sqmm XLPE/AL./PVC sheathed.

INSTALLATION OF HV CABLE END TERMINATION

Termination of XLPE insulated Indoor type , Unearthed /Earth grade HV cables of following sizes, including cutting and stripping of cable insulation, crimping the lugs onto the conductor, executing termination using termination kit (Heat Shrinkable/ Push‐on type), restoration of the insulation, fixing of cable glands (including drilling of suitable holes in equipment for fixing purpose), connection of leads, clamping, including anti tracking compound, ferrules, clamps, Aluminum tags, clamping of cores and earthing of armour, installation & supply of PVC shrouds and PVC Hoods of required size for outdoor terminations including all labour and materials complete as per approved drawings, specification of this tender and direction of Engineer‐in‐charge. The contractor to also arrange suitable Stop Plugs for unused entry, if required. The cost for supply of suitable bimetallic strip (if required) shall be included in termination, no separate payment shall be made for bimetallic strip. In case of bimetal connection, contractor to supply and use suitable bimetallic strip.

3 Core cables 6.6 kV , 400 sqmm XLPE/AL./PVC sheathed.

SUPPLY & INSTALLATION OF LV CABLE TERMINATION

POWER CABLE Termination of XLPE / PVC insulated armored cables (upto 1100 V grade) and connection of leads, cutting and stripping of cable insulation, fixing of cable gland (including drilling of suitable holes in equipment for fixing purpose), crimping the lug on to the conductor, clamping of the cable cores (Multicore cable), anti tracking compound, SS tags,( Al tags at an interval of 30 Mtrs.s & at cable bends) tagging and earthing of armour and Drilling of gland plats for glands wherever required, installation of cable glands, PVC shrouds, stopping plug including all materials supply & marking with wire number ferrules etc. supply of all necessary consumables and GI hardware, supply & installation of PVC shrouds for outdoor terminations including all labour and materials complete as per approved drawings, directions, of Engineer‐in‐charge. The cost for supply of suitable cable Lugs & bimetallic strip (if required) shall be included in termination, no separate payment shall be made for bimetallic strip. In case of bimetal connection, contractor to supply and use suitable bimetallic strip.

Cables with OD upto 20 mm.

Cables with OD above 20 mm but upto 30 mm

Cables with OD above 30 mm but upto 40 mm

Cables with OD above 40 mm but upto 55 mm

CONTROL CABLE Termination of XLPE / PVC insulated, extruded PVC sheathed, twisted pair, overall shielded armoured control cables (upto 1100 V grade) and connection of leads, cutting and stripping of cable insulation, fixing of cable gland (including drilling of suitable holes in equipment for fixing purpose), crimping the lug on to the conductor, clamping of the cable cores, supply & marking with wire number ferrules etc. supply of all necessary consumables and GI hardware, supply & installation of PVC shrouds for outdoor terminations including all labour and materials complete as per approved drawings, directions, of Engineer‐in‐charge. The cost for supply of suitable cable Lugs & bimetallic strip (if required) shall be included in termination, no separate payment shall be made for bimetallic strip. In case of bimetal connection, contractor to supply and use suitable bimetallic strip.

All sizes from 1 to 4 pairs and upto 2.5 Sq.mm

All sizes from 5 to 10 pairs and upto 2.5 Sq.mm

All sizes from 11 to 15 pairs and upto 2.5 Sq.mm

FO CABLE Supply and installation of FO Cable termination including installation of LIU unit , providing of ODTR, patch cord & other accessories required for end termination & also provides necessary tools / tackles, authorized technician for FO cable termination & as per direction of Engineer‐in‐charge.

SUPPLY AND INSTALLATION OF CABLE GLANDS / PLUGS

SUPPLY AND INSTALLATION OF CABLE GLANDS / PLUGS: Flameproof type

Cables with OD upto 20 mm.

Cables with OD above 20 mm but upto 30 mm

Cables with OD above 30 mm but upto 40 mm

Cables with OD above 40 mm but upto 55 mm

Cables with OD upto 20 mm.

SUPPLY AND INSTALLATION OF CABLE GLANDS / PLUGS: Weather-proof type

Cables with OD upto 20 mm.

Cables with OD above 20 mm but upto 30 mm

Cables with OD above 30 mm but upto 40 mm

Cables with OD above 40 mm but upto 55 mm

Cables with OD upto 20 mm.

Cables with OD above 20 mm but upto 30 mm

MARKERS

Supply and installation of cable markers (as per the details provided in installation standard for power) for buried HV/MV cable at the interval of 30M, at every bend & at every cable joint location. The marker shall be of minimum 14 SWG enamelled steel plate with white lettering on jade green background. supply of associated materials including engraving and fixing supports shall be in contractor's scope. "BURIED ELECTRIC CABLES HT/LT" complete with support and foundation, painting, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

Supply and installation of earth pit markers for directly buried G.I / Cu pipe electrodes. The marker shall be of minimum 14 SWG enameled steel plate with white lettering on jade green background. supply of associated materials including engraving and fixing supports shall be in contractor's scope. "BURIED EARTH ELECTRODE" complete with support and foundation, painting, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

SUPPLY & INSTALLATION OF ELECTRICAL CABLE TRAYS

Supply, Installation of Prefabricated hot dip galvanized steel (fabricated out of hot rolled sheet steel with rigid welded construction) ladder/perforated type cable trays / bends / cross / reducers / Tee / other cable trays accessories etc., Handling, shifting from contractor's site-store / yard to the installation location, unpacking, assembling and including installation of coupler plates, hold down clamps, all G.I. hardware required etc. Including cutting to required size, making bends, elbows, Tee wherever required, cable tray fittings, including all labour and materials, as per installation standard, approved drawings, specification of this tender, approved make and directions of Engineer-in-charge. Application of Al paint / Cold zinc spray paint on all welded / damaged surfaces is to be carried out by the contractor. It also includes any modification work because of fouling with pipelines, structures & as per site condition. Note- The installation of cable trays shall also be required to be carried out at height. Provision of scaffolding for same shall be in contractor scope and nothing extra shall be payable in this regard.

Ladders type cable tray

150 mm wide x 100mm side rail height Straight run ladder type cable tray

300 mm wide x 150mm side rail height Straight run ladder type cable tray

600 mm wide x 150mm side rail height Straight run ladder type cable tray

600 mm wide x 150mm side rail height Straight run ladder type cable tray including cover

90 Degree Horizontal bends for 150 mm wide tray with 600 mm bending radius

90 Degree Ladder type Horizontal bends for 300 mm wide, height 100mm cable tray with 750 mm bending radius

90 Degree Horizontal bends for 600 mm wide cable tray with 900 mm bending radius

90 Degree Vertical outside bend ladder type, for 150 mm wide, height 100mm cable tray with 600 mm bending radius

90 Degree Vertical outside bend ladder type, for 300 mm wide, height 100mm cable tray with 1000 mm bending radius

90 Degree Vertical outside bend ladder type, for 600 mm wide, height 100mm cable tray with 1250 mm bending radius

90 Degree Vertical outside bend ladder type, for 600 mm wide, height 100mm cable tray with 1800 mm bending radius

90 Degree Vertical inside bend for 150 mm wide cable tray with 600 mm bending radius including cover

90 Degree Vertical inside bend for 300 mm wide cable tray with 600 mm bending radius

90 Degree Vertical inside bend ladder type, for 300 mm wide, height 100mm cable tray with 1000 mm bending radius

90 Degree Vertical inside bend ladder type, for 600 mm wide, height 100mm cable tray with 1250 mm bending radius

90 Degree Vertical inside bend for 600 mm wide cable tray with 900 mm bending radius including cover

45 Degree Vertical inside bend for 300 mm wide cable tray with 600 mm bending radius

Right hand side reducers 600 - 300 mm including cover

Left hand side reducers 600 - 300 mm including cover

Right hand side reducers 300 - 150 mm including cover

Left hand side reducers 300 - 150 mm including cover

Perforated cable tray

50 mm wide

100 mm wide

150 mm wide

Installation of Prefabricated hot dip galvanized steel (fabricated out of hot rolled sheet steel with rigid welded construction) ladder/perforated type cable trays / bends / cross / reducers / Tee / other cable trays accessories etc., Handling, shifting from contractor's site-store / yard to the installation location, unpacking, assembling and including installation of coupler plates, hold down clamps, all G.I. hardware required etc. Including cutting to required size, making bends, elbows, Tee wherever required, cable tray fittings, including all labour and materials, as per installation standard, approved drawings, specification of this tender, approved make and directions of Engineer-in-charge. Application of Al paint / Cold zinc spray paint on all welded / damaged surfaces is to be carried out by the contractor. It also includes any modification work because of fouling with pipelines, structures & as per site condition. Note- The installation of cable trays shall also be required to be carried out at height. Provision of scaffolding for same shall be in contractor scope and nothing extra shall be payable in this regard.

300 mm wide x 150mm side rail height Straight run ladder type cable tray

SUPPLY AND INSTALLATION OF CONDUITS FOR POWER & FO CABLE LAYING / PROTECTION

PVC Conduits: 25 mm NB.

PVC Conduits: 50 mm NB.

GI Pipe: 25 mm NB.

GI Pipe: 50 mm NB.

HDPE PIPE SLEEVES: 50 mm NB. For F.O cable

HDPE PIPE SLEEVES: 100 mm NB.

HDPE PIPE SLEEVES: 150 mm NB.

HDPE PIPE SLEEVES: 200 mm NB.

PVC Conduits: 50 mm NB.

PVC/HDPE PIPE SLEEVES: 100 mm NB.

PVC/HDPE PIPE SLEEVES: 150 mm NB.

RCC HUME PIPES

Supply & Installation of NP3 class Hume pipe including collars. Sizes: 300 mm NB

INSTALLATION OF HIGH MAST & FEEDER PILLARs

Receipt of material from OWNER'S store / yard, Handling and transportation to the installation location, Installation, cable/wire termination of fixtures, Testing and Commissioning of the complete lighting system, using Raising and Lowering type of High mast Towers, including control panel, setting of timer, including Civil Foundation , Erection , Earthing Works. All items required for the safe and efficient operation and maintenance of the lighting system, including the high mast, whether explicitly stated here under or not, shall be included by the Contractor. This includes necessary excavation, providing concrete foundation including supply of cement and associated materials disposal of surplus earth, providing shoring,shuttring, dewatering if required and other civil works as necessary, including fixing of G.I pipes, G.I flat for earthing purpose, steel, base plates, paint and all sundry materials as required, all labour and materials complete as per approved drawings, specification of this tender and directions of Engineer-in-charge. Major items are as follows a) 30 M High mast system including double drum winch, SS wire rope, trailing cable, lantern carriage suitable to install 24 Nos. luminaries in symmetrical arrangement, Flame proof plug socket connector, Flame proof integral power tool motor, manual handle, junction box, lightning finial with down conductor b) Foundation bolts manufactured from special steel along with nuts, washers, anchor plates and templates. c)LED Floodlight fittings with driver and all accessories in pre wired condition. Hard ware for fixing fittings on lantern carriage should be supplied with the fittings. d) Outdoor stand mounted Flame proof feeder pillar suitable for gas group IIA/IIB, Temp. Class T3. Foundation Cost will be paid separately. refer Civil SOR. e) Lightning Finial:-One number heavy duty 1.2m long hot dip galvanized lighting finial shall be provided for each mast on the head frame to get a direct conducting path to the earth through the mast. Lightning Finial shall be insulated from body and head frame of High Mast and a separate down conductor (1Rx1Cx120sqmm copper Armored flexible Cable shall run from the lightning finial to an earthing bolt independent of the high Mast structure.

SUPPLY & INSTALLATION OF LIGHTING FIXTURES/CONTROL GEAR BOX - WP

2x 40 W LED Linear Lighting Fixtures with accessories suitable for mounting suitable for surface / suspended from ceiling / wall/ structure, with IP55 degree of protection, electronic components in pre wired condition with all accessories

120 W LED flood light fixture including LED lamps, constant current driver, suitable for surface / suspended from ceiling / wall/ structure, with IP55 degree of protection, electronic components in pre wired condition with all accessories

150W LED flood light fixture including LED lamps, constant current driver, suitable for surface / suspended from ceiling / wall/ structure, with IP55 degree of protection, electronic components in pre wired condition with all accessories

40 W LED Lighting Fixtures with accessories suitable for mounting suitable for surface / suspended from ceiling / wall/ structure, with IP55 degree of protection, electronic components in pre wired condition with all accessories

45 W LED Lighting Fixtures with accessories suitable for mounting suitable for surface / suspended from ceiling / wall/ structure, with IP55 degree of protection, electronic components in pre wired condition with all accessories

2x 36 W LED Linear Lighting Fixtures with accessories suitable for mounting suitable for surface / suspended from ceiling / wall/ structure, with IP55 degree of protection, electronic components in pre wired condition with all accessories

LED Exit Light 6 W, indoor, LED Exit sign (Written with "EXIT") board including supply of fixing fasteners, Transportation of material from storage place to work area, INSTALLATION, CONNECTION OF LIGHTING FIXTURE ( WITH CABLE GLANDS, PVC SHROUD), Installation, testing, commissioning of lighting luminaires

40 W, Recess Mounted

SUPPLY & INSTALLATION OF LIGHTING JUNCTION BOXES - WP

Supply, installation, earthing, testing and commissioning of dust and vermin proof G.I sheet steel ( 1.6 mm thick ) weather proof junction box suitable for outdoor / indoor installation with number of outgoing ways as under, complete with PVC connectors, supply and fixing of cable glands, including supply of required size and number of terminals, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

4 way junction box, The junction box shall be suitable for incoming/outgoing cables of size 3CX 2.5 sq.mm. / 4 sq.mm.

INSTALLATION OF LIGHTING FIXTURES & JUNCTION BOXES - HAZARDOUS AREA

Installation, connection, testing and commissioning of following types of flame proof/Div.2 lighting fixtures, junction boxes and accessories, including cable termination and connection, fixing of cable glands, Erath ring, lugs, including supply of necessary hardware's, including transportation from store/yard to site at the place of installation, unpacking, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. Installation of Equipment (wall / concrete / steel structure mounted) shall be as per 'Installation Details - Lighting' and applicable construction documents. Note: All the FLP Equipment will be supplied by the other contractors as free issue material.

Well glass LED, Integral Type - Zone 2, Group IIC-LM6, MOC Cast Al Alloy, 120 Watt LED (Bracket mtd.) with LED Driver, 230V AC

Well glass LED, Integral Type - Zone 2, Group IIC-LM6, MOC Cast Al Alloy, 45 Watt Linear LED Lamp (Pendant mtd.) with LED Driver, 230V AC

Street Lighting Fixture (90W LED lamp with LED driver and Junction Box) - Zone 2, Group IIC-LM6, MOC Cast Al Alloy

2x 36 W LED Linear Lighting Fixtures with accessories suitable for mounting suitable for surface / suspended from ceiling / wall/ structure, with IP55 degree of protection, electronic components in pre wired condition with all accessories

4 way junction box - Zone 2, Group IIC-LM6, MOC Cast Al Alloy

Flameproof & weatherproof led well glass lighting fixture with 40w, type (ex-de iib t3 ip55) suitable for zone- 2 (for critical lighting), battery operated, backup-60 minutes.

SUPPLY & INSTALLATION OF WELDING SOCKETS / POWER SOCKETS

63A, 415 Volt, 3 phase, 50 HZ, 5 pin sockets along with associated 5 pin plug

SUPPLY & INSTALLATION OF SOCKETS/CONVENIENCE OUTLETS

Safe area, 5A/15A, Single Phase, 240V AC, 3 PIN (P+N+E) Socket/Convenience receptacle along with associated plug. With 2 pole and earth, metal enclosed plug top along with 20 amps. C curve, DP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, with loop-in loop-out facility and complete with connections, testing and commissioning etc. as required. Note:ISI marked sockets shall be used.

Installation, Earthing ,Testing & Commissioning of weather proof / flame proof socket outlets on steel structures/concrete column/wall etc., including installation of canopies, if any . This also includes supply of necessary hardware, touch up painting, stenciling if required, Including Lifting & Transportation from storage area to the place of installation with contractor's own lifting and transportation arrangement, unpacking, assembly, including all labour and materials, complete as per approved drawings, specification of this tender and directions of Engineer-in-charge. Excluding fixing of cable glands and cable termination.

Flame proof (Ex'd', IIC, T3), 16A, Single Phase, 240V AC, 3 PIN (P+N+E) Socket/Convenience receptacle along with associated plug.

Safe area, 5A/15A, Single Phase, 240V AC, 3 PIN (P+N+E) Socket/Convenience receptacle along with associated plug. With 2 pole and earth, metal enclosed plug top along with 20 amps. C curve, DP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet, with loop-in loop-out facility and complete with connections, testing and commissioning etc. as required. Note:ISI marked sockets shall be used.

SUPPLY & INSTALLATION OF LIGHTING POLES

Supply and installation of street lighting poles (single bracket/double bracket) including built in marshalling box/JBs and necessary wire/cable running from marshalling box to the lighting fixture, cable termination and connection, fixing of cable glands and lugs, including all civil works, excavation, foundation, disposal of surplus earth, providing shoring, strutting and dewatering if required and including supply of cement, steel, GI pipes, base plates, paint and all sundry materials as required, including painting, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge. -

Lighting pole, 90W LED lamp with LED driver and Junction Box - Safe area , MOC Cast Al Alloy as per standard no :0814-B000-STC-1693-001 (STREET LIGHTING FIXTURE MOUNTED ON POLE)-11m Height Pole

3.0 Mtr high J pole mounted including junction box & clamp. As per standard no. 0814-B000-STC-1693-001

WIRING

Circuit wiring in non-hazardous areas using copper conductor ( as per below given size), PVC/XLPE insulated armoured cables (third core for earthing), from lighting / power panels / distribution junction boxes onwards, excluding the supply of cables but including supply of junction boxes and cable glands, including fixing of cable glands, supply and fixing of clamps, cable terminations and connections, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

3C x 4 Sq.mm

3C x 2.5 Sq.mm

4C x 2.5 Sq.mm

POINT WIRING

All Point wiring in concealed/ surface conduit including supply and erection of GI/PVC conduits with complete accessories, copper wires, recessed GI boxes housing switches/ sockets of 5A/ 15A rating, lighting fixture box including chipping and remaking of chases for walls/ ceilings for embedding conduits, cutting and sealing of wall for installing boxes etc. Conduit shall form part of point wiring and will not be paid separately.

SUPPLY AND WIRING OF LIGHT POINT CONTROLLED BY ONE WAY SWITCH (MODULAR TYPE)

Supply and wiring of light point with 2.5 sq.mm PVC insulated , FR, copper conductor wire in surface/ recessed 25 mm dia GI/PVC conduit including all accessories on surface or in recess, including supply and fixing of 5A one way switch/ GI box including circuit wiring, earthing of light fixture with 2.5 sqmm PVC insulated FR, copper wire etc. as required. The above scope includes cutting, chasing of wall and filling the chases with mortar and making good finish as required. Wire and switch shall also form part of point wiring and will not be paid separately.

SUPPLY AND WIRING OF LIGHT POINT CONTROLLED BY MCB IN DISTRIBUTION BOARD ( LDB )

Supply and wiring of light point controlled by MCB upto 16A in LDB with 2.5 sq.mm PVC insulated, FR, copper conductor wire in surface/ recessed 25 mm dia GI/PVC conduit / Metsec channel including all accessories on surface or in recess, including earthing of light fixture with 2.5 sqmm PVC insulated, FR, copper conductor wire etc. as required. The above scope includes cutting, chasing of wall and filling the chases with mortar and making good finish as required. Wire shall also form part of point wiring and will not be paid separately.

SUPPLY & WIRING OF 15/5A SWITCH SOCKET OUTLET (MODULAR TYPE)

Supply and wiring of 3/5 pin 15A switch socket outlet with 2.5 sq.mm PVC insulated, FR, copper conductor wire in surface/ recessed 25 mm dia GI/ PVC conduit including all accessories on surface or in recess, including supply and fixing of switch socket outlet, GI box, cover plate including earthing of 3rd pin with 2.5 sqmm PVC insulated FR single core copper wire etc. as required. The above scope includes cutting, chasing of wall and filling the chases with mortar and making good finish as required. Wire and switch socket outlet shall also form part of point wiring and will not be paid separately.

Supply and wiring of 3 pin 5A switch socket outlet with 2.5 sq.mm PVC insulated, FR, copper conductor wire in surface/ recessed 25 mm dia GI/ PVC conduit including all accessories on surface or in recess, including supply and fixing of switch socket outlet,GI box, cover plate including earthing of 3rd pin with 2.5 sqmm PVC insulated FR single core copper wire etc. as required. The above scope includes cutting, chasing of wall and filling the chases with mortar and making good finish as required. Wire and switch socket outlet shall also form part of point wiring and will not be paid separately.

SUPPLY AND INSTALLATION OF EXHAUST FAN

Supply, installation, testing and commissioning of 240V, 1-Ph, 18 inch sweep Industrial Type corrosion proof Exhaust Fan with guards / louvers & necessary brackets (for Battery Room)

Installation, testing and commissioning of 240V, 1-Ph, 18 inch sweep Industrial Type corrosion proof Exhaust Fan with guards / louvers & necessary brackets (for Battery Room)

Supply, installation, testing and commissioning of 240V, 1-Ph, 300 mm sweep Industrial Type corrosion proof Exhaust Fan with guards / louvers & necessary brackets (for Battery Room)

SUPPLY AND INSTALLATION OF CEILING FAN

Supply, installation, testing and commissioning of ceiling fans of Bajaj/Crompton Greaves/Khaitan/Usha make only including supply and fixing of the electronic regulators, cable/wire termination of fan, with all necessary supports. All complete with labour and materials as per drawings, specifications and directions of Engineer-in-Charge 1200 MM SWEEP (WHITE)

installation, testing and commissioning of ceiling fans of Bajaj/Crompton Greaves/Khaitan/Usha make only including supply and fixing of the electronic regulators, cable/wire termination of fan, with all necessary supports. All complete with labour and materials as per drawings, specifications and directions of Engineer-in-Charge 800 MM SWEEP (WHITE)

INSTALLATION OF POWER JUNCTION BOXES & WELDING OUTLETS (WOs)- HAZARDOUS AREA

POWER JUNCTION BOXES (PJBs)-FLP Installation of following types of FLP junction boxes, as per specification, including suitably sized busbars with current rating equal to the largest cable current rating, SS plug for unused opening, glands, lugs, earthing terminals, canopy etc., including all materials, as per approved drawings, T.EN specifications.

Type-3 : Power Junction Box . INCOMING CABLE SIZE: 1 RUNS OF 3Cx120 SQ.MM OUTGOING CABLE SIZE: 1 RUN OF 3Cx95 SQ.MM

Type-3 : Power Junction Box . INCOMING CABLE SIZE: 2 RUNS OF 3Cx240 SQ.MM OUTGOING CABLE SIZE: 2 RUN OF 3Cx150 SQ.MM

Type-2 : Power Junction Box . INCOMING CABLE SIZE: 1 RUN OF 3C (35-120) SQ.MM OUTGOING CABLE SIZE: 2 RUN OF 3C (6-70) SQ.MM Mounting : wall / concrete / steel structure

Type-1 : Power Junction Box . INCOMING CABLE SIZE: 3 RUNS OF 3C (150-300) SQ.MM OUTGOING CABLE SIZE: 2 RUN OF 3C (120-300) SQ.MM Mounting : wall / concrete / steel structure

WELDING OUTLETS (WOs)-FLP Installation Flameproof & weatherproof LM6, 63A, 415V, TPN, industrial type socket and plug with heavy duty interlocking switch, with adequately sized cable adaptor box , including supply of double compression brass nickel plated cable glands, plug for all opening, tinned copper lugs, including all materials, as per approved drawings, T.EN specifications.

SUPPLY & INSTALLATION OF POWER JUNCTION BOXES (PJBs)-WP

Supply, installation, testing and commissioning of following types of WP junction boxes, as per specification, including suitably sized busbars with current rating equal to the largest cable current rating, glands, lugs, earthing terminals, canopy etc, including all labors and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-Charge.

Type-2 : Power Junction Box . INCOMING CABLE SIZE: 1 RUN OF 3C (35-150) SQ.MM OUTGOING CABLE SIZE: 1 or 2 RUN OF 3C (6-16) SQ.MM Mounting : wall / concrete / steel structure

Type-3 : Power Junction Box . INCOMING CABLE SIZE: 2 RUNS OF 3C (185-300) SQ.MM OUTGOING CABLE SIZE: 1 or 2 RUN OF 3C (70-150) SQ.MM Mounting : wall / concrete / steel structure

SUPPLY AND INSTALLATION OF EARTHING AND LIGHTNING PROTECTION

Supply of materials, Handling, shifting from contractor's site-store / yard to the installation location, unpacking, assembling and installation of earthing and lightning protection systems and accessories underground / wall / concrete / steel structure / cable trays - as recommended by MANUFACTURER / applicable construction documents and other associated work so as to ensure the completeness of installation work. Testing, precommissioning and commissioning activities as detailed in the items below and scope of work document attached with the Tender document are included in the scope. EARTHING (Installation shall be as per 'Installation Details - Earthing' and applicable construction documents.)

SUPPLY AND INSTALLATION OF EARTHING SYSTEM ACCESSORIES

Supply, installation, laying, clamping and connecting following G.I/Cu earth conductors for main earth grid / earthing network in cable trenches, along structure, cable trays, racks, walls, roofs etc., including welding at joints, chipping and remaking of concrete surface, supply and fixing of G.I clamps, Supply and fixing G.I fasteners at earth plate or wherever required. Supply & applying anti-corrosive paint or bitumen and jute covering for welded portion on underground joints & cold zinc spray on aboveground joints. It also includes any modification work because of fouling with under ground/above ground piping. All hardware shall be SS304, Including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

75 x 10 mm GI earth strip

50 x 6 mm GI earth strip

25 x 3 mm GI earth strip

Supply, laying, clamping and connecting individual equipment to the earth strip or earth plate with following sizes of G.I wire / G.I wire rope, including supply of required lugs, conductors, all hardware shall be SS-304 for connections, Including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

10 mm Dia G.I flexible wire rope

16 mm Dia G.I flexible wire rope

Supply, laying, clamping and connecting individual equipment to the earth strip or earth plate with following sizes of insulated single core copper conductor flexible cables , including supply of required lugs for connection at both end, crimping, all hardware for connections, Including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

2.5 sqmm PVC insulated green/yellow earthing cable

6 sqmm PVC insulated green/yellow earthing cable

10 sqmm PVC insulated green/yellow earthing cable

16 sqmm PVC insulated green/yellow earthing cable

25 sqmm PVC insulated green/yellow earthing cable

6 sqmm PVC insulated yellow earthing cable

25 sqmm PVC insulated yellow earthing cable

6 mm2 CU Insulated Ring type Lug

25 mm2 CU Insulated Ring type Lug

Nut-Bolt SS-304, M10X50mm

Nut-Bolt SS-304,M8X50mm

SUPPLY AND INSTALLATION OF EARTHING OF PIPELINES, FLANGES & VALVES Earthing of the following items, including supply and fixing of earthing lugs over Pipe line, flanges & valves, Fasteners, Cu lugs of suitable size wherever required. Applying cold zinc spray on aboveground joints. including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

Pipeline earthing (Pipe to pipe connection) with 1 X 25 sqmm Cu Conductor Unarmoured cable as per Typical earthing installation details & Earthing layout.

SUPPLY AND INSTALLATION OF ELECTRICAL EARTH PITS

Supply & Installation of G.I. earthing Nos. Supply & installation of maintenance free chemical (Number electrode copper coated G.I. pipe station with 500 mm ) long 75X10 G.I. busbar having 4 no's connecting holes, bimetallic washers.65 mm dia, 3 meter long with 2 Nos. X 20 kgs of chemical bags with test certificate required as per standard IS 3043. Providing RCC ready made chamber or bricks chamber with machinery & plaster, identification stand with sticker pit cover plate complete. The scope also covers including supply of nutbolt, washer, all tools & tackles etc. The chamber size should be inner side min 500 mm dia. All test certificate required. These earthings are required for Lightning Arrestor, GOD structure & Fencing, panels, Instrument etc.. Refer installation standard drawing Doc. no. 0814-B000-STC-1691-001.

G.I Earthing bar 400 x 75 x 10 mm with holes

SUPPLY AND INSTALLATION OF LIGHTNING PROTECTION

Supply of materials Handling, shifting from site-store / yard to the installation location, unpacking, erection, alignment, assembling and installation of special lightning protection system - as recommended by MANUFACTURER / applicable construction documents, and other associated work so as to ensure the completeness of installation work. Testing and precommissioning activities, commissioning assistance as required by MANUFACTURER's supervisor is included in the scope. Minor civil work such as chipping and replastering the same as per the site requirement (including the supply of consumable material for the same) is included in the scope. Supply of all fixing hardware as per the site requirement is included in the scope. Installation of lightning down conductor and lightning pits, as required, is considered separately in this document under the respective headings.

Lightning Arrestor (Air terminal-1500m long)

Test Link Box Providing and fixing testing joint, made of 25mm x 3mm thick, GI strip, 125mm long, with 4 Nos. of GI bolts, nuts, check nuts and spring washers etc. complete as required.

Strike Counter Analog Lightning Strike Counter, Count Capacity: 200KA

MISCELLANEOUS ITEMS

SUPPLY, FABRICATION, INSTALLATION OF STRUCTURAL STEEL WORK

Supply, Fabrication and installation of various sizes steel for supports, brackets for miscellaneous electrical equipment, base frames, support for switchgear, hangers, risers, clamps etc. for miscellaneous electrical equipment / items, cable and cable tray supports with rolled MS sections, pipes, plates, strip etc., including shot blasting, welding, bolting, riveting, supply of necessary anchor bolts and grouting etc. Including supply of paint and applying two coat of anti-rust primer & two finished coats of approved synthetic enamel paint including breaking walls, floors etc. for structures as required, including supply of all G.I hardware materials, including all labour and materials, complete as per approved drawings, specification of this tender and directions of Engineer-In-charge. Any item weighing up to 1 kg or less shall neither be measured nor paid.

EXCAVATION AND BACKFILLING

Excavation and back filling of trenches for directly buried cables and earth conductor in all type of soil except rock, for a max. depth of 1.5 M shoring, shuttering and dewatering / deoiling using pneumatic pump (if necessary) including consolidation and disposal of surplus earth outside refinery or as per direction of Engineering-in-charge, including all labour and materials complete as per approved drawings, specification of this tender and directions of Engineering-in-charge. Trenches shall be duly rammed and levelled. (excavated trench dimensions shall be measured)

Supply and filling /spreading of approved fine river sand / stone dust in buried cable trenches and in RCC cable trenches including removal of RCC trench covers/slab, refixing of RCC trench Covers/Slabs after filling/spreading the sand, including all labour and materials complete as per approved drawings, specification of this tender and directions of Engineering-in-charge.

Fine river sand

Supply and spreading / laying of second class bricks of 75 mm thickness in buried cable trenches and in RCC cable trenches (for cable protection) including removal of RCC trench covers/slab from RCC trench, refixing of RCC trench covers/Slab after laying of bricks, if required, including all labour and materials complete as per approved drawings, specification of this tender and directions of Engineering-in-charge (actual area of laid brick surfaces shall be measured).

Supply, fabrication and installation of 6mm thick M.S. chequered plates for covering / sealing floor cut-outs / cable trenches etc. including cutting, grinding, fixing Lifting hooks in Chequered plates etc., including all labour and materials, complete as per approved drawings, specification of this tender and directions of Engineering-in-charge.

Supply and laying plain cement concrete for all depths below and up to plinth level in foundations including tamping, ramming, vibrating, cutting, shuttering etc. all as specified in any shape, position, thickness and finishing the top surface rough or smooth as specified and directed, including supply of all materials and all complete for concrete of M-15 grade with 20 mm and down size graded crushed stone aggregates, including all labour and materials, as per approved drawings, specifications of this tender and directions of Engineer-in-charge.

Cable chamber for HT Cable Joints on cable Racks : Supply, Installation of cable chamber of suitable size for Cable joints including excavation of earth, supply of civil material, back filling, making wall partition inside cable chamber, numbering , including all labour and materials as per directions of Engineer-in-charge.

Supply & Laying of black stones Supplying, Laying, Spreading & leveling of black stones/gravels(min size-40mm) in the Transformer-1&2 of SS-4.

REMOVAL OF BRCKS IN CABLE TRENCH

Removal of bricks from cable trench without any damage to the cable and disposing it within a lead of 50 meters or stacking it at the edge of the trench and putting it back into the same trench or in a new cable trench as per drawing/ specification within a lead of 50 meters after the work is completed including completing the work in all respects with all labour and materials as per the direction of the Engineer- in-Charge.

Removal and relaying

CABLE LAYING IN EXISTING TRENCH

Laying of new cable in existing concrete trenches including Identification of existing trenches, removal of existing precast concrete slabs from top of trench, removal of filled sand, laying of new cables, re-filling of sand, levelling of sand, replacement of precast concrete slabs on trench, re-placement of trench markers as per specifications and also including supply of sand (as required) as per instructions of site in charge

Trench size upto 1000 mm (W) X 2000(D) mm

DISMANTLING AND DISCONNECTION OF ELECTRICAL EQUIPMENTS

Disconnection, dismantling of existing industrial / flameproof local control stations, Socket outlets and power distribution electrical equipment, without any damage to it, including transporting to owner's store including all labour and materials, as per specifications of this tender and as per directions of Engineer-in-Charge.

Panel / Unit weight from 6 kgs to 20 kgs

SUPPLY AND INSTALLATION OF ANCHOR FASTENERS

Supply, drilling in RCC and fixing of metallic anchor fasteners for supporting of cable trays and miscellaneous electrical switchgear of following sizes, including all labour and materials, complete as per approved drawings, specification of this tender and directions of Engineer-in-charge.

SUPPLY AND INSTALLATION OF SEALING COMPOUND

Supply of sealing compound (Bituminous tar or approved equivalent) heating and pouring of compound in the cable stuffing box of flameproof motors and providing effective cable sealing, including all labour and materials, specifications of this tender and directions of Engineer-in-charge (measurement of weight shall be made for sealing compound supplied).

Supply of water proof / fire proof material for sealing cable entries inside the substation buildings, motor termination, Field termination etc.

FIRE PROOFING OF CABLES

supply and installation of Fire proofing of cables, to meet OISD requirement (for 3 Mtrs. length near terminations), including supply of all fire proofing paint, including all labour and materials, specifications of this tender and directions of Engineer-in-charge (Actual area of surface painted shall be measured).

SUPPLY AND INSTALLATION OF SAFETY EQUIPMENT

Supply and installation of the following, including the supply of necessary clamps, bolts, raw plugs etc., breaking and making good of walls, if required, mounting, including all labour and materials, complete and as per applicable latest Indian standards, CEA regulations and as per directions of Engineer-in-charge.

Shock hazard charts complete with aluminum frame and glass

First Aid Boxes

8 Liters capacity CO2 type fire extinguishers

Enameled caution boards

Single Line Diagram's (SLD) for Substations with wooden frame & glass in A0 size

Supply and laying of 900 mm wide safety insulation mats complying to IS-15652, of following grades required for maintenance of electrical equipment in substation, including cutting to required shape in running length, including all labour and materials, as per applicable latest Indian or International standards, CEA regulations and as per directions of Engineer-in-charge

3.3 kV Grade

Supply of following items as per applicable latest Indian standards / CEA regulations. Supply of the items and all the associated accessories of reputed make. Make shall be approved by Owner / Consultant.

Rubber hand gloves (3.3 kV grade)

Digital Clamp Meter of following specification: Digital True Rms Clamp Meter suitable for Industrial application having features for measurement of AC/DC Voltage and Current , Resistance, Continuity, Temperature, Frequency, Capacitance. It should also have features like Overload protection, Auto power off, Hold, Low battery voltage indicator, Large backlit LED screen etc. . Current measurement range 0- 600 Amps or more. Operating Temperature -10 °C to + 50 °C.

GENERAL ITEMS Supply of following items and all the associated accessories of reputed make. Make shall be approved by Owner / Consultant, all supplied material shall be industrial grade, ISI certified.

Implementation of LOTO system during precommissioning & commissioning stage (Key station, red lockes-30nos, Hasp-10nos. Etc.)

Electrical Standars Tool Kit including all like Spanners , Torque Wrenches, Screw Drivers ,Pliers , Cutters ,Knives, Crimping Tools for Cable Lugs Make: Bosch , Hilti, Teperia.

Supply & Installation of Tarpaulin (for weather protection of stored electrical equipment)

Supply & Installation of 3 ply Lamicoid tag plates of appropriate size for various equipment, with White letters on Black background, as per the site requirement

MANPOWER RATE

Providing technical assistance during pre-commissioning / commissioning phase by deploying different categories of skilled personnel as listed below .The quoted man-months rates shall be inclusive of all wages, overtime for working beyond normal hours including holidays / weekly off, travel / accommodation expenses, including PPE’s, all tools & tackles etc and other costs which the bidder shall be entitled to claim by way of Man-Month Rates for the services. Prior to deployment of personnel at site, Contractor shall submit the detailed CVs of such persons proposed to be posted at site to Owner for concurrence & approval. The Owner and Contractor shall jointly maintain a record of all such personnel chargeable at Man-Month Rates deployed each day which shall be used as the basis for calculating payments due to the Contractor for the services covering assistance during pre-commissioning & commissioning phase. For deployment covering part of the month, payment shall be made on pro-rata basis considering 30 days in a month. Should the performance of any of Contractor’s personnel be found unsatisfactory by Owner, the replacement of such personnel shall be carried out by Contractor immediately.

Electrical Supervisor

Technician/ Electrician

Helper

SUPPLY AND APPLICATION OF PAINTING, LETTERING AND STENCILING

Letter painting and marking of all buses of switchboards, all incomers, bus couplers, outgoings with details of Tag No, feeder rating in KW/Amp, sending end source, in the front of the panels and bus bar, panel Nos.etc. on the rear side of the panels for all switchboards, all other substation equipment viz.transformers, capacitors, neutral grounding resistors, VFD panels, other panels, etc for equipment housed in electrical substations including supply of all material such as stickers, enamel paints, stencil, etc including supply of all labour, materials as per the specification of this tender and directions of Engineer-in-Charge. -

Letter writing including supply of approved colour of Paint/Paints (Fluorescent) above 2 inch and Upto 4 inch in height/length

Surface painting to supply of paints and primers, surface preparation and application of primer and finish paints ( as per project specification) , identification, lettering, colour bands,colour coding etc. as per instruction of site in charge and touchup with primer & finish paint wherever required, providing scaffolding for all heights, labour, material, tools and tackles, consumables, etc to complete the work in all respect as per job specification. Paint shall be Asian/ Berger/ Nerolac /Shalimar .

Letter writitng including supply of approved colour of Paint/Paints (Fluorescent), painting of tag number (approx. 25-50 mm high) of items like detectors, hooters, beacons, manual call points, etc. as specified by Engineer -In-Charge.

All coordination and liasoning activites with statutory authorities( CEA) related to Electrical system installation shall be part of Contractor Scope and all documentation and obtaining clearance for energization for the work executed under this package.

Supply and Installation of Exhaust fan (300mm Dia), 230v Supply, 50 Hz for Toilets

Bidder Name

Amount

M/s HAL Offshore Limited (GSTN-NA) BID ID -839241

BRIDGE AND ROOF COMPANY INDIA LIMITED (GSTN-NA) BID ID -839247

Description of Work / Item(s)

Amount

Grouting: Non-shrink grout (GP1/GP2) for equipment and steel structures, Ordinary Cement Sand Grout for Minor Structure/Platforms

Supply and laying of Non-shrink cementitious grout Conbextra GP of FOSROC or Equivalent for grouting of base plates, under base frames or other anchoring elements for structures and/or machines, including roughening & cleaning of surfaces, form-works, chamfering of edges, smoothing of exposed surfaces, Curing, making flush to the existing RCC surface by chipping & finishing, RCC surface to be made wet for 24 hrs. before grouting, providing all tools and labour necessary to complete the work as per drawings and manufacturer’s specifications and as per the directions of Engineer-in-charge.

Epoxy grout for equipment

Supply and laying of epoxy grout Conbextra EP65 of FOSROC or Equivalent (7 days minimum compressive strength 90 N/mm2) for grouting of base plates, under base frames or other anchoring elements for structures and/or machines, including roughening & cleaning of surfaces, form-works, chamfering of edges, smoothing of exposed surfaces, Curing, making flush to the existing RCC surface by chipping & finishing, providing all tools and labour necessary to complete the work as per drawings and manufacturer’s specifications and as per the directions of Engineer-in-charge. Inspections and Tests.

Fireproofing for steel structures/ equipment saddles, etc.

Supplying and Applying all types of Fireproofing (Vermiculite Based/ in-situ Concrete/ Sprayed Mortar) as per Specifications, Drawings and Standards for any steel element wherever required, such as columns, beams, wind-bracing, girders, equipment legs, skirts and saddles at any height, either “box” or “contour shaped”, including form-works, supply and installation of reinforcement mesh, primer paint on structural / equipment surface, expanded metal sheet/ lath, nuts, fixing of cover plate (MS edge angle) at both side of top exposed structural beam, cover blocks and hooks, studs, mastic sealing between the Fireproofing edges and the structural steel elements all complete including mobilising/ demobilizing all tools, equipment and labour as required to complete the work to the satisfaction of Engineer-in-Charge. Painting over Fireproofed Surfaces (For both Vermiculite and in-situ Concrete/ Sprayed Mortar Fireproofed Elements): Supplying and Applying of Painting over Fireproofed Surfaces after full curing (minimum gap of 28 days) of all types of Fireproofing applied. The Base Coat shall be a sealer coat of Epoxy Polyamide @ 50 – 75 micron DFT. The Finish Coat shall be of two coats of Acrylic Elastomeric or Polyurethane coating @ 100 – 125 micron DFT per coat. The Finish Coat shall be UV resistant coating system (No 1 of NORSOK standard M-501). The Coating System shall be compatible and approved by the Fireproofing Material Vendor. Locations identified as following 1) Skirt (both Inside and Outside) of IA and UA receivers – 3 Nos 2) All structural steel members (mainly pipe supports) inside dyke area of Px, HSD and LSHS tanks

Anchor Bolts

Supplying, fabricating, casting, installing and fixing in position of M.S.holding down threaded bolts conforming to IS 2062 Grade A as per drawings at all levels and locations, including supply and fixing nuts, washers, anchor plates, pipe sleeves, etc., for equipment supports, stacks, tanks, vessels, structural steel columns, foundations, including supplying, fabricating, straightening if required, and installing necessary templates, providing auxiliary dummy structures, if any, necessary tying and welding to reinforcement, adjustment of shuttering & reinforcement/any other fixture, greasing exposed metal surfaces and covering bolts and packing the sleeves with jute cloth etc., all complete and as per drawings and specifications, and as directed by the Engineer in Charge. ( No extra payment shall be given for template or any dummy structure)

For Anchor Bolts ( Grade 4.6 & 8.8) of any dia.

Supply and installation of Mechanical or Chemical bolts, from an approved manufacturer like “HILTI” or equivalent as per drawings, including the cost of the bolts, carting the same to site of work, fixing in position with necessary, tools, labour etc. for all heights with necessary scaffoldings and depths, drilling holes and fastening as per manufacturer’s specifications, all complete as specified in the Drawings and directions of Engineer-in-charge.Inspections and Tests as per relevant technical specifications and codes shall be deemed to be included in the scope Chemical Bolts - Hilti HAS-E Rod or Equivalent

STAIR TREADS –Supply and Erection of Treads made up of Gratings as prefabricated panels including delivering the same to the actual site of execution. Scope shall include all activities like Supply and fixing of all type of Connection Bolts (Erection, Hot Dip Galvanised/Non-Galvanised Permanent bolts) as per Specifications, Welding, Aligning, making necessary alterations caused due to mismatch of Bolt Holes, Torque Tightening of Bolts, cleaning, giving final touch up paints as per specifications to the welded parts, etc as required complete with all tools, equipments and labour, for all depths and heights along with all related works in order that the Structure is handed over to the complete satisfaction of the Engineer-in-charge. Inspection and testing.

Supplying, fabricating and delivering to site steel flooring (Chequered Plates of any thickness) for all types of platforms and as per standard drawings and/or specifications, including cost of steel, incorporating cut-outs where shown in drawings, providing drainage holes, painting / galvanising as specified, repairs of damaged surface coat after erection, complete with all tools, equipments and labour, for all depths and heights as per drawings and as directed by Engineer-in-Charge.

Supply, Fabrication and Erection of structural steel of E250 / E350 grade as per drawings / instruction of EIC. Making holes for bolting / welding as mentioned in the drawing, surface preparation and applying all coats of paints

Supplying, fabricating and delivering to site steel flooring (G I gratings of Type - I / II) for all types of platforms and as per standard drawings and/or specifications, including cost of steel, incorporating cut-outs where shown in drawings, providing drainage holes, hot dip galvanising as specified, repairs of damaged surface coat after erection, complete with all tools, equipments and labour, for all depths and heights as per drawings and as directed by Engineer-in-Charge.All types of Galvanized (Type - I / II) Gratings and stringers/stair treads. Applying cold galvanizing spary on welded portions Inspection and testing.

Supplying, fabricating and delivering to site steel flooring (G I gratings of Type -Heavy duty) for all types of platforms and as per standard drawings and/or specifications, including cost of steel, incorporating cut-outs where shown in drawings, providing drainage holes, hot dip galvanising as specified, repairs of damaged surface coat after erection, complete with all tools, equipments and labour, for all depths and heights as per drawings and as directed by Engineer-in-Charge.All types of Galvanized (Type - I / II) Gratings and stringers/stair treads. Applying cold galvanizing spary on welded portions Inspection and testing.

Providing TOE GUARD in cutouts of gratings with G I Flat. Applying cold galvanizing spray on welded portions

Supply and Transportation of Materials required to Fabricate of Handrails, in standard lengths and delivering the same to the actual site of execution or to the designated warehouse.Erection of already fabricated Handrails as per requirements indicated in Standard Drawings, IFC Layouts and Fabrication Drawings. Scope shall include all activities like Supply and fixing of all type of Connection Bolts (Erection, Hot Dip Galvanised/Non-Galvanised Permanent bolts) as per Specifications, Welding, Aligning, making necessary alterations caused due to mismatch of Bolt Holes, Torque Tightening of Bolts, cleaning, giving final touch up paint as per specifications to the welded parts, etc as required complete with all tools, equipment and labour, for all depths and heights along with all related works in order that the Structure is handed over to the complete satisfaction of the Engineer-in-charge. Supply of erection nuts and bolts / fasteners are included in this item. Inspection and testing.

Supply & Fabrication of Structural Steel Materials for Ladders with or without Cage including arranging required labour, consumables, equipment, tools and tackles, etc., loading, unloading, intermediate handling, transportation to painting yard, collecting from painting yard and carting the same to erection site / laydown area complete in all respects.

Supply and fixing of Sheeting for elevation up to 20 Mtr from grade

Supply and fixing of Sheeting for elevation from 20 Mtr to 30 Mtr from grade

Supply and fixing of luveurs for rain water

Supply and fixing of rain water gutter piping

Surface preparation and application of paints of all coats as per specification - C S Structural steel

Description of Work / Item(s)

Amount

Work Copde 2010

Overhead Sintex Water Tanks Supply of all materials & installation of overhead tank of polyethylene with material conforming to IS codes including all fittings, cover with locking arrangement, float valve, inlet, outlet, vent pipe etc. all complete. Scope shall include Base Preparation of 300 mm thick using Bricks masonry / Cement concrete (1:2:4) / Cement Sand Mortar (1:3 Mix), to place the Tanks in position on top of the buildings.

Tank Capacity 1500 Litres

Tank Capacity 1000 Litres

Stainless Steel Handrails Providing and fixing, stainless steel (Grade 304) railing made of Hollow tubes channels, plates etc, of height 1000 mm with top rail 50 mm NB , middle rails ( 3 Nos) of 20 mm NB and verticals as 40 mm NB@900mm c/c with all bends, elbows , etc., including welding, grinding, Buffing, polishing and making curvature (wherever required) and Fitting the same with necessary stainless steel nuts and bolts all Complete including making drills in structures, fixing the railing with necessary accessories & stainless Steel dash fasteners, stainless steel bolts etc., of required size, on the top of the floor or chipping & fixing inside RCC or the side of waist slab complete as per drawing /standards complete in all respect to the satisfaction of Engineer-in-charge.

Rectangular Handrails

Circular/Curved Handrails

Water Cooler Cap - 50 Ltr Supplying and Fixing Water Coolers with all necessary accessories like Taps and their Connections, etc all inclusive as required and as per the instructions of the Engineer-in-charge

For Tank capacity 50 litres.

For Tank capacity 20 litres.

Work Code 2020

White washing Providing and applying three coats of white wash (with fat lime slaked at site, thinned with water and gum, ultramarine blue added) to give a smooth and even shade, including tools & labour, clearing and preparation of surfaces, necessary scaffolding etc complete for all heights.

Color washing Providing and applying three or more coats of colour washing with lime base and colour pigment to give a smooth and even shade, including tools & labor, cleaning and preparation of surfaces, necessary scaffolding etc complete for all heights.

Plastic emulsion Paint Painting with plastic emulsion, two coats with approved quality paint of "DULUX" or equivalent of approved shade , over the coat of approved primer, including tools & labour, preparation of surfaces with Plaster of Paris / white cement putty, sand papering, plugging all holes / cracks and depressions, scaffolding etc complete for all heights as per specifications and as per the directions of Engineer-in-charge

Excluding Surface Preparation using Plaster of Paris/ white cement putty

Including Surface Preparation using Plaster of Paris/ white cement putty

De corative waterproof cement paint Providing & applying as per manufacturer's instructions, water proof decorative cement paint finish of "Snowcem" or approved equivalent of approved shade in two or more coats, over a coat of primer if required to give an even shade, including tools & labor, preparation of surfaces, scaffolding, curing etc. complete for all heights

Oil bound distempering Providing two coats of oil bound distempering conforming to IS:428 including tools & labor, preparation of surfaces, making good of uneven plaster with Plaster of Paris / white cement putty mixed with water, sand papering, providing a priming coat of alkali resistant distemper primer etc. all complete and as per directions of Engineer -in-charge

Exterior acrylic finish for walls Providing and applying/ finishing the walls/ RCC surfaces with Premium Acrylic smooth exterior paint with silicon additives of required shades on new work applied in two or more coats at the rate of 1.43 ltr/ 10 sq.m over and including primer base coat of waterproof cement paint, including tools & labor, filling all cracks with white cement and pigment to match, cleaning the surface of all dust before evenly applying with brush / roller, curing, drying the coated surfaces for 24 hours etc all complete and as per directions of Engineer-in-charge.

Exterior texture paint for walls Providing and applying / finishing the walls/ RCC surfaces with exterior texture paint, including tools and labours ,filling all cracks with white cement and pigment to match, cleaning the surface of all dust before evenly applying with brush, curing, drying the coated surfaces for 24 hours etc all complete and as as per directions of Engineer-in-charge.

Work Code 2030

Heavy Duty Cement Concrete Flooring Providing and laying average 50mm thick heavy duty cement concrete flooring in panels consisting of base course of 35mm thick cement concrete (1 cement : 1.5 coarse sand : 3.5 stone aggregates of 10mm to 6mm size by volume) laid over sub-base in panels (each panel not exceeding 1sqm in area) in desired shape & pattern and 15mm thick finishing layer consisting of cement , hardener & stone aggregate mix of 15 mm thickness laid over the base course. Ironite / non- metallic or equivalent metallic integral hardening compound in proportion of 1 part of ironite to 4 parts of ordinary Portland cement by weight, laid integral with base course and finished smooth including cost of cement, clearing the sub-base surface, applying neat cement slurry over sub-base to receive the base course, levelling, tamping, trowelling, finished, curing, providing shuttering to the edges, providing panel dividers using Fibre Glass / PVC / or Glass Strip, etc. all complete and as per directions of Engineer-in-charge.

Using Fibre Glass Material for Panel Dividers

Using Glass Strips for Panel Dividers

Using PVC Panel Dividers (3 X 40 mm)

Cement Granolithic flooring Providing and laying average 40mm thick cement concrete granolithic flooring in panels consisting of 25mm thick base course (under layer of M-15 grade cement concrete with 6mm down size stone aggregates) laid over sub-base, 15mm thick top layer of cement mortar (1 cement : 3 coarse sand by volume ) finished smooth by tamping, trowelling, and with a finishing floating coat of neat cement slurry @ 2.75kg. of cement per Sq.m. of area, including cost of cement, tools, labo ur, cleaning the sub- base surface, applying neat cement slurry over the sub -base @ 2.75Kgof cement per Sq.m of area to receive the base course, compacting, tamping, trowelling, finishing, curing, providing shuttering to the edges, providing Fiberglass/ PVC/ Glass panel dividers, etc. all complete and as per directions of Engineer-in-charge.

Cement concrete flooring Providing and laying 25 mm thickness over sub-base and shall generally conforming to IS:2571. 25 mm thick base course of M-15 grade cement concrete (with 6mm & down size stone aggregate) laid o n the sub -base in panels (each panel not exceeding 1 sqm in area) in desired shape & pattern. The panels shall be bound by 3x20 PVC / glass strips panel dividers; fixed in position with their top at proper level maintaining the required levels, slopes, linearity etc. as required. Base course shall be laid in alternate panels. cement slurry @ 2.75kg. of cement per Sq.m. of area, including cost of cement, tools, labour, cleaning the sub -base surface, applying neat cement slurry over the sub -base @ 2.75Kg of cement per Sq.m of area to receive the base course, compacting, tamping, trowelling, finishing, curing, providing shuttering to the edges, providing panel dividers, etc. all complete and as per directions of Engineer -in-charge.

125 mm high Skirting Providing and laying 12 mm thick, 125mm high cement plaster skirting with 1:3 cement mortar (1 cement : 3 coarse sand by volume) finished with a floating coat of neat cement slurry @ 2.75kg. of cement per Sq.M of area including rounding of junctions with floor, preparing the wall surface, making recess in the wall, finishing, curing etc. all complete with Cement supplied by Contractor at their cost.

Vitrified tiles in flooring, skirting Providing and Laying Vitrified Tiles in Flooring and Skirting of Approved Shape, Size and Shade confirming to IS:770 and including cost of Tile cutting, providing a 30 mm thick bedding in cement mortar 1:4 mix, providing a coating of adhesive (SHAKTI of Bh arat Adhesive co or UNTILE or any other approved equivalent make) as per manufacturer’s specifications, flush pointing and filling of joints with cement slurry (using white cement), providing the pigment confirming to IS:2114, Table 1 matching the shade of the tiles, finishing, curing, protecting the surface with POP till final handing over etc. all complete as per drawings, specifications and as directed by Engineer -in-charge.

For white glazed vitrified tiles of size 600 mm x 600 mm x 8 mm thick to be used in Flooring

For coloured glazed vitrified tiles of size 600 mm x 600 mm x 8 mm thick to be used in Flooring

For white glazed vitrified tiles of size 125 mm x 8 mm to be used in skirting

For coloured glazed vitrified tiles of size 125 mm x 8 mm to be used in skirting

Non-slip glazed ceramic tiles Providing and laying glazed, ceramic matt-finished, non-slip decorative type tiles of specified size & approved make (SPARTEK or approved equivalent) including cleaning the finished surface with Oxalic acid, wax polishing (Manson/ Waxpol) as per Manufacturer’s specifications and / or as per the instructions of the Engineer -in-charge

300mm x 300mm x 8mm thick tiles

200mm x 100mm x 6mm thick tiles

125 x 8mm thick tiles in skirting

Wall tiles on walls

Kota stone flooring, landings, treads Providing and laying machine cut chisel dressed kota stone slab of 20 mm thickness and approved shade in floors over a under layer average 15mm thick cement mortar 1:6 (1 cement : 6 coarse sand by volume), including preparing the base surface, applying neat cement slurry to receive the mortar, providing neat cement slurry @ 4.4kg. of cement /Sq.M of area over the mortar bed, jointing each slab with neat cement paste/ grouting (white cement and pigment conforming to IS : 2114, Table -1, matching the shade of slabs), curing, , grinding, machine / hand polishing the tiled surface, mirror / mat finishing etc. all complete as per drawings, specifications and as per directions of Engineer-in-charge.

Kota stone in skirting, risers Providing and fixing in skirting 125mm high chisel dressed 20 mm thick Kota Stone slab of approved shade of specified thickness, laid over average 12mm thick cement mortar1: 3 (1cement: 3 coarse sand by volume) including tools, labor, chipping the brickwork / concrete wherever necessary and applying a coat of cement mortar 1:3 mix 15mm (average) thickness, curing, rubbing, machine / hand polishing the tiled surface, finishing to match with the wall plastering, jointing the slabs with grey cement slurry mixed with pigment to match the shade o slabs including rubbing and polishing, etc. all compete as per drawings, specifications and as per directions of Engineer-in-charge.

Granite flooring Providing and laying of 20 mm thick pre-polished, premium quality and approved shade Granite Stone Slabs in Flooring, Counters, Treads, Risers, Skirting, dado, etc over and including 30 mm thick bed of cement mortar in 1:4 including cost of cement, tools, labour, preparation of base surface, applying neat mortar cement slurry @ 2.75 kg of cement per sqm of area to receive the mortar bed, filling the joints with matching pigments, full round moulding, polishing, providing 3 Nos of 4 mm wide non -slip grooves at the nosing end of landin gs, etc all complete as per drawings, specifications and as directed by Engineer -in-charge.

Jet Black shade Granite Flooring, Treads

Acid / Alkali re sistant tiles Providing and fixing 10 mm thick Acid and / OR Alkali Resistant Tiles of approved make and colour using Acid and / or Alkali Resisting Mortar bedding, and joint filled with acid and / o r alkali resisting cement as per IS:4457, as per manufacturer’s recommendations, etc . all complete as per specifications and directions of Engineer-in-charge

In flooring on a bed of 10 mm thick mortar 1:4 (1 Acid Proof Cement : 4 Coarse Sand)

In dado / skirting on 12 mm thick mortar 1:4 (1 Acid Proof Cement : 4 Coarse Sand)

Chemicals and abrasion resistant floor coating Providing and applying pigmented chemical and abrasion resistant, solvent based, self-levelling floor coating of approved shade based on epoxy resin with amine curing agents, in 2 coats @ 125 gms / sqm (min) per coat applied by brush or spray over a 3mm (minimum) thick levelling screed consisting of a 3-part solvent free combination of epoxy resin, amine hardeners and graded chemically inert aggregate filler of high strength. The System shall include an Epoxy Resin Primer and Scr eed, which are both supplied in pre-weighed units ready for on-site mixing and application. Scope shall include all tools, labour, surface preparation & installation as per manufacturer’s recommendations, curing etc . all complete as per drawings, specifications and as per directions of Engineer -in-charge.

Chemicals and abrasion resistant skirting & Dado Providing and applying pigmented chemical and abrasion resistant, solvent based coating of epoxy resin with amine curing agents of approved shade, on dado wall in 2 coats @ 125 gms / sqm (min) per coat and applied by brush over plastered concrete surfaces, including tools, labo ur, surface preparation & installation as per manufacturer’s recommendations, curing etc. all complete as per drawings, specificatio ns and as per directions of Engineer-in-charge.

WorkCode 2040

False ceiling – Type 1 Providing and fixing False Ceiling Grid Framework for supporting ceiling tiles consisting of main and cross runners supported from roof slab at desired height in desired pattern including finishing, making the framework perfectly levelled and aligned, etc. all complete as per specifications and directions of Engineer-in-charge. Anodised (25 micron) Aluminium grid framework consisting of extruded anodised aluminium (2.5 mm thick) main runners (T shaped, 25 mm x 35 mm size), cross runners (T Shaped 25 mm x 25 mm size), Wall Angles including suspending the main runners @ 600 mm c/c maximum, by means of 6 mm dia M.S. Hooks slotted in 25 mm x 25 mm x 3 mm thick M.S. Angle fixed to roof slab with dash fasteners and connected to 3 mm thick M.S. Clamp (connected to main runners with 25 mm long M.S. Nut) with levelling nut @1200 mm c/c maximum assembling the main and cross runners by means of aluminium angle cleats inter locking each other to form the grid work of 600 mm size maximum, fixing the aluminium wall angles with dash fasteners, etc. all complete

Same as 2040.05.00 but using 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I

Same as 2040.05.00 but using Prefinished/ Pre-Coated mineral fibre ceiling tiles having Min. NRC value 0.70

Under deck insulation with resin bonded fiber/ mineral wool board Providing fixing thermal insulation of ceiling (under deck insulation) with Resin Bonded Fibre glass wool conforming to IS : 8183, density 24kg / m3, 50mm thick, wrapped in 200 G Virgin Polythene bags, fixed to ceiling with metallic cleats (50 x 50 x 3 mm) @ 60 cm and wire mesh of 12.5 mm x 24 gauge wire mesh, for top most ceiling of building, as per manufacturer’s recommendations, & specifications and directions of Engineer -in-charge

False flooring/ cavity floor – All Depths - Type -2 Providing and fixing truly levelled and aligned false flooring/ cavity flooring up to 1200mm deep consisting of: • Powder coated pedestal assembly shall consist of a formed hot dip galvanized (60-80 micron) mild steel base plate with not less than 150mm x 150mm x 4 mm of bearing area, mechanically riveted to a 32mm dia. of 2 mm thick CRCA steel pedestal designed to engage the head assembly. • Zinc electroplated CRCA steel pedestal head assembly shall consist of 90mm x 90mmx 4 mm thick profiled head, mechanically riveted to a 19 mm dia threaded bright rod, fixed to pedestal by specially designed zinc electroplated steel forged adjusting nut for levelling, locking and changing the height setting. • Stringers shall be of hot dip galvanized (60 -80 microns) steel, minimum 20mm x 32mm x 1.20mm thick CRCA steel. • Floor panels shall be 600mm x 600mm size, minimum 35 mm thick powder coated (40-60 micron) CRCA steel cementitious core panel (with hemispherical and reverse cones) and 1 mm thick epoxy painted CRCA steel sheet on top. Top sheet shall be finished with 2mm thick high pressure laminate or 2mm thick conductive PVC or as per project specification. The inner empty core shall be injected with light weight fire retardant non - combustible cementitious compound. All edges of the panels shall have conductive PVC trims. • Floor panels shall be capable of supporting following loading conditions when tested as per CISCA test procedure. o Concentrated load of 675 Kg. with maximum allowable deflection of 2 5mm and a factor of safety of 2.5. o Uniform load of 2025 Kg/ Square meter. • Fire rating of floor panels shall be class 0 & class 1 conforming to BS 476-part-6 (Fire propagation) and BS 476-part-7 (Surface spread of flame). • All accessories such as outlet boxes and grommets as required, Panel lifters (at least one for each building, one number for every 500 Square meter of access floor area) etc. shall be provided in accordance with approved Manufacturer's recommendations. • The base floor and cavity between false flooring and base floor shall be properly cleaned and made dust free and dry. The base cement concrete floor shall be treated with one component polyurethane based coating.

For 600 mm deep flooring

Workcode 2050

Pressed steel hollow box type door Providing, fitting and fixing hollow box type door shutter consisting of 18SWG pressed steel sheet bent to form hollow box of 40mm overall thickness of hollow space in between the two facing sheets of the shutters, frame suitably shaped in the form as per drawing, mitred, welded at meeting with 2mm thick M.S. pad plate all along the perimeter, forming square edges at corners and braced with channel shaped 35mm wide 16 SWG M.S. sheet horizontal stiffener @ 50mm max, providing heavy duty 125mm long M.S. butt hinges @ 600mm max, spring loaded pressure die cast zinc alloy door stopper for each shutter, bolting device with padlock of approved quality, M.S. holdfasts 25 x 25 x 6mm and 300 mm long for embedment in concrete, painting with approved shade electrost atic powder coating (25 micron)/ 2 coats of Synthetic enamel over red oxide zinc chromate primer coating etc. all complete and as specified. The scope shall include the Supply and Installation of 16 gauge Pressed Steel Frames 125 X 60mm (to be filled back side hollow portion with concrete) required to install the Doors as per manufacturer’s recommendations, & specifications and directions of Engineer-in-charge

For Single shutter with 6 lever, heavy duty mortice lock, pressure die cast zinc alloy handles on both faces, two nos. of 10mm dia. 250mm long M.S. tower bolt, one no. 1 6mm dia, 250mm long M.S. aldrop, Door Stopper etc.

For Double shutter with 12mm dia, 300mm long pressure dia cast zinc alloy handles on both sides, 10mm dia, 250mm long M.S. tower bolt for each shutter, 1 6mm dia, 250mm long M.S. aldrop, Door Stopper etc.

Steel windows/ ventilators Providing and fixing steel glazed/ louvered window/ ventilator consisting of steel sections, as per IS: 7452/ 1361/ 1038 for framework and shutters with4mm thick plain sheet glass conforming to IS: 2835 (wt.: 7.2 kg / m2), joints mitred, electrically flash butt welded to form solid, true edges, cor ners and glazing fixed to the frame work by means of special metal sash putty & glazing clips, steel square beading with approved make brass oxidised fitting, 18 SWG M.S. sheet louvers welded to frame as per drawings, including tools, labour, fixing them to masonry/ RCC by means of 100mm x 15mm x 6mm M.S. lugs welded to frame @ maximum 750mm c/c and suitably embedded into concrete, painting with two coats of synthetic enamel paint (ICI or equivalent make) of approved shade over a coat of red oxide zinc chromate primer (for steel surfaces), mastic filling, providing and fixing friction hinges, brass handles, striking plate, stay, push fit weather bars etc. all complete and as specified. The scope shall include the Supply and Installation of Steel Frames required to install the Window/ Doors as per manufacturer’s recommendations, & specifications and directions of Engineer-in-charge

For openable type

Glazed anodized/ powder coated aluminum doors, Windows and Ventilators Supplying and fixing fully glazed anodized (25 micron)/ electrostatic powder coated (25 micron, approved shade) aluminium doors with approved make and including all accessories like Steel/ Aluminium Beading, with extruded tubular aluminium sections of thickness between 2.0mm to 3.2mm and 5.5 mm toughened glass fixed with rubber lining and anodized aluminium beading, including all tools and labo ur, fixing the frame to masonry/ RCC with 16mm wide, 8.2mm thick 100mm x 70mm galvanised L-shaped slotted lugs screwed to the frame @ 600mm ma x. by counter sunk galvanised machine screws and grouting to masonry with M-15 grade concrete in minimum 150mm x 150mm x 50mm sized hole/ 96mm long 12mm dia dash fastener, cup pivots of aluminium alloy as per requirements of the Architectural Aluminium Man ufacturers Association (AAMA), heavy duty hydraulically operated, adjustable floor mounted door closer (double action), 250mm and 150mm long, 10mm dia anodized aluminium tower bolt, one each for each shutter, brass body mortice lock (6 levers) with aluminium handle on both sides, and etc. all complete for each shutter, finishing and making good of any damaged work etc. all complete as per attached drawing and as directed.

Openable doors

Openable type windows and Ventilators

Fixed type windows and Ventilators

Louvered/ Fixed type windows and Ventilators

Supplying and Fixing in position Door Stoppers for Doors

18 SWG ste el rolling shutter Supplying and fixing in position 18 SWG mild steel push and pull type rolling shutters, conforming to IS: 6248 including tools, labo ur, all accessories like shutter (constructed with inter locking lath sections formed out of col d rolled steel strips 0.9mm thick, 80mm wide and 1.25mm thick, 80mm wide respectively for shutter width up to 3.5M and above 3.5M), jointless M.S. channel section for guide (min. 3.15mm thick), M.S. girders, pressed bottom rails, shutter suspension stud sh aft with pully and cage with cowl, top rolling springs, locking arrangement and all fittings and accessories as per approved manufacturers drawings, painting with two coats of synthetic enamel of approved make & shade over a coat of approved quality red oxide zinc chromate primer, making good of all damaged surfaces etc. all complete and as directed.

Mechanically operated from both inside and outside by reduction gear type mechanism

Mild steel gate Providing and fixing in position collapsible mild steel gate single or double according to opening size. These shall consist of vertical double channel each 20 x 10 x 2mm at 100 mm centre braced with flat iron diagonals 20 x 5mm top and bottom rail of Tee iron 40 x 40 x 6mm @3.5 kg/m with 38mm steel pulleys or ball bearing in every fourth double channel unless otherwise specified all tools and labour etc complete and as directed. • Providing and fixing in position Sliding mild steel/ pressed steel gate single or double according to opening size. Including 38mm steel pulleys or ball bearing in every 300mm unless otherwise specified all tools and labour etc complete and as directed.

Sliding mild steel/ pressed steel gate (Non motor operated)

Workcode 2060

Block board doors/ shutters Providing and fixing Factory made, overall 40mm thick block board flush shutter consisting of solid core block board bonded with phenol formaldehyde synthetic resin and faced on both faces with commercial type plywood/ teakwood veneering/ lamination bonded with phenol formaldehyde synthetic resin, including tools, labo ur, fixing `T' type second class teakwood perimeter beading fixed by means of approve d quality neoprene based adhesive and nailing @ 300 mm max, painting exposed surface with two coats of approved shade and make synthetic enamel paint over approved quality primer coat, fixing 125mm long M.S. butt hinges [for each shutter, and with vertical spacing not exceeding 600mm) with door frame, finishing etc all complete and as directed. The scope shall include Supply and Installation of all Accessories like Vision Panels, Overhead/ Floor Mounted Hydraulic Door Closer, Mortise Door Locks, Handles on Doors, Tower Bolts, Kick Plates, latches, door stopper etc such that the Doors are handed over in a completed position. The scope shall include the Supply and Installation of Pressed Steel Frames required to install the Doors as per manufacturer’s recommendations, & specifications and directions of Engineer-in-charge

Door shutter faced with 1 mm lamination on both sides.

Wooden frames Providing and fixing wooden frames for doors and windows of size 100 X 60 mm or 120 X 60mm, including fixing the frame with masonry/ RCC/ metal frame work for partition etc. M.S. holdfasts grouted with M-15 grade concrete in min 350 mm x 100 mm x 100 mm sized hole in masonry all complete as per instructions of Engineer-in-charge.

With second class Indian Teakwood

Providing & Installing 100mm wide vertical blinds in external windows.

False Partitions Providing & Fixing 12.5mm thick Gypsum boards for partitioning & panelling. Number of Gypsum board layers (single skin or double skin) shall be as specified and with finishing (painting or lamination) as specified. Frame work along the edges shall be concealed with partition/ panel boards. Necessary cut-outs electrical, AC, return air etc. and other fixtures shall be provided in the boards. Glazing if any shall be fixed with putty and wooden beadings. MS frame for Partitioning & Panelling shall consist of horizonta l & vertical members of18SWG 52mm X 38mm MS sections. The members shall be welded to each other at maximum 600mm c/c both ways. The frame shall be fixed to the floor/ ceiling/ wall with GI roulette plug, screw and washers & 300mm maximum c/c. The members shall be provided with one coat of red oxide zinc chromate primer. The frame-work arrangement shall be in accordance with the pattern for partition including doors/ windows etc. All Complete as per specifications and as per instructions of Engineer-In-charge

Painted

Workcode 2070

Pan type water closet (Indian type ) Providing and fixing Hindware make or approved equivalent white glazed earthenware Orissa type pan water closet with integral footrest conforming to IS:2556 Part-III, including P/ Q/ R type trap, glazed earthenware flushing cistern of required capacity confirming to IS:774, CP brass with handle supported on M.S. brackets, 32mm dia telescopic flush pipe with fittings and clamps, 15mm dia GI overflow pipe with mosquito proof net, galvanised iron chain and handles, 15mm dia PVC connection pipe 450mm long, pain ting of all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint over a priming coat of red oxide zinc chromate, cutting walls, floors and making good of same, finishin g soldered joints, making inlet/ outlet connections, providing minimum 150mm thick sand cushion, finishing all tools & labour, including all accessories as required like white cement, etc all complete as per manufacturer’s specificat ions, drawings/ specifications and as directed by Engineer-in-charge

Flushing Cistern Capacity – 8 Litres

Water closet (western type) Providing and fixing Hindware make or approved equivalent white glazed earthenware double trap, symphonic pattern wash down water closet confirming to IS: 2556 Part-II including plastic seat and cover confirming to IS:2556, CP brass hinges and rubber buffers, required capacity glazed earthenware low level cistern confirming to IS:774 with internal overflow system and fittings, CP Brass 40mm dia. Flush pipe, 15mm dia PVC connection pipe 450mm long, painting with two coats of approved enamel paint over a coat of primer for all metallic surfaces, cutting walls and fl oors and making good the same, making inlet and outlet connections including all accessories as required like white cement, etc. all complete as per manufacturer’s specifications, drawings, specifications and as per directions of Engineer-in-charge

Flushing Cistern Capacity – 8 Litres

Urinals Providing and fixing Hindware make or approved equivalent white glazed ceramic, flat back half stall type Urinals of 610mm x 400mm x 380mm size confirming to IS: 2556 Part-VI including automatic glazed earthenware cistern, 15mm dia C.P brass cistern outlet 750mm long, 32mm dia GI waste pipe with brass union, C.P brass bottle trap, C.P. brass spreader, tee, distribution pipe etc. M.S. brackets for cistern, breaking walls, floors and making good of same, painting all exposed metallic surfaces with 2 coats of approved shade and quality synthetic enamel paint over a priming coat of approved quality red oxide Zinc Chromate, making inlet and outlet conne ctions, fixing with C.P. brass screws, finishing etc. all complete

For a set of one Urinal with 5 litres capacity Flushing Cistern

Providing and fixing in position 25mm thick, 900 mm high marble partitions with round edges for Urinals, including breaking walls, fixing for 100mm depth in C.M. 1:3, fixing with M.S. brackets, channels at top and bottom making good the wall, painting the channels etc. complete with all tools & labour.

Providing and fixing Hindware Italian collection Venezia 91011 on-counter wash basin including Jaguar Florentine 5005B single lever mixer, Jaguar Allied 709 32 mm waste coupling, Jaguar Allied 769 32 mm CP Bottle Trap, Jaguar Continental 053 KN CP Angle Cock, Jaguar Allied 803B 450 mm long bradied hose etc of the same or approved equivalent make all complete as per drawings, manufacturer’s specifications and as directed by Engineer -in- charge

Providing and fixing white glazed vitreous china lab sink/ kitchen sink of 610 x 450 x 25mm size of "Hindustan Twyford" or equivalent make with C.I. brackets painted white, one 15mm dia C.P. brass Bib Cock, 15mm dia PVC pipe connection, C.P. brass chain with 40mm dia G.I. pipe connected to floor trap with necessary unions, including tools & labor, cutting and breaking the floor or wall and making good the same, etc . all complete as per specifications and directions.

Providing and fixing in position bevelled Edge Mirror of "Hindustan Pilkington" or equivalent make glass as approved of size 600mm x 450mm x 5.5mm thick complete with round edge with 20mm Aluminium Angle edging fixed on 13mm thick solid core board, fixed to wooden cleats with C.P. brass screws, breaking walls and making good the same etc. complete

Providing and fixing in position 600mm x 120mm x 4mm thick glass shelf of Jaguar or equivalent approved quality and make with CP brass bracket and guard rails complete assembly fixed to cleats with C.P. brass screws, cutting and making good the wall etc. complete

Providing and fixing Jaguar make or approved equivalent 15mm diameter CP brass stop cock of heavy grade of spring loaded self-closing type, concealed / exposed, including tools and labo ur, making connections, cutting walls and pipes and making good the sa me etc. all complete

Bib cocks Providing and fixing Jaguar make (Continental range Catalogue Reference CON-041KN) or approved equivalent 2 way Bibcock complete as per drawings/ specifications and as directed by Engineer-in-charge

Pillar cocks

Nahani traps Providing and fixing approved quality heavy grade cast iron Floor/ Nahani Trap with CP pressed steel grating, including tools & labo ur, cutting walls and floors and making good the same, making Inlet and Outlet connections etc. all complete, including the inlets Outlet of required sizes.

100 mm Inlet and 100 mm Outlet

100 mm Inlet and 80 mm Outlet

Heavy duty CI soil/ PVC/ waste pipes below ground Providing and fixing approved quality heavy duty CI Soil/ PVC/ Waste pipe of specified diameter conforming to IS: 3486 below ground, with necessary special bends, jointing with lead calked joints and testing the same, cutting in floors / walls and making good the same, earth work in excavation, back filling and removal of surplus earth up to a lead 50 M etc. all compete as per drawings and as directed.

For 150mm dia CI Soil pipe

For 100mm dia CI Soil pipe

CI soil Wastenad Vent pipe above ground Supplying and laying cast iron soil waste and vent pipe of specified diameter conforming to IS: 1729 above ground, including tools & labo ur, special bends such as T-Y junction (both single and double) including plugs, shoes, cowls, jointing with jute gasket dipped in bitumen, caulking the joints in CM 1:2 and testing, cutting in floors/ walls and making good the same etc. all complete as per drawings and as directed.

For 100mm dia CI pipe

Providing and fixing Jaguar make Single Lever Bath and Shower Mixer (Jaguar Florenine Range Catalogue Reference CAN-1171N) or any other approved equivalent all complete as per drawings, specifications and as directed by Engineer-in-charge.

Providing and fixing Jaguar make Toilet Paper Holder (Jaguar Catalogue Reference AHS-1551) or any other approved equivalent all complete as per drawings, specifications and as directed by Engineer -in-charge.

Providing and fixing Jaguar make Double Coat Hook (Jaguar Accessories Range Catalogue Reference CAN-1161N) or any other approved equivalent all complete as per drawings, specifications and as directed by Engineer-in-charge.

Providing and fixing Jaguar make 600 mm long SS Towel rack (Jaguar Catalogue Reference ASH-1581) or any other approved equivalent all complete as per drawings, specifications and as directed by Engineer -in- charge.

Providing and fixing hand Drier all complete as per drawings, specifications and as directed by Engineer-in-charge.

Providing and fixing Jaguar or equivalent make Soap Container all complete as per drawings, specifications and as directed by Engineer -in- charge.

GI Pipe Class C for Plumbing Providing and Laying Class C GI Pipes of any dia (Tata/ Jindal or any other approved equivalent) in concealed manner including cost of all required fittings (R-band) like bends, couplers, tees, reducers, stoppers, cla mps, chasing in brick/ concrete and making good, removal of debris, application of non-corrosive bitumen paint on GI Pipes, testing and commissioning, etc. all complete as per drawings, specifications and as per the directions of the Engineer-in-charge

For pipes of Dia 15 mm

For pipes of Dia 20 mm

For pipes of Dia 25 mm

For pipes of Dia 32 mm

For pipes of Dia 40 mm

Plumbing Valves Providing and Fixing bronze ball valve with screwed female flanged ends with stainless steel valve and spindle, glass filled Teflon seating and gland packing, quarter turn, lever operated full bore design, hydraulically tested to 20kg /sqcm. Pressure. -Valve and Non return valve 15mm - 50mm dia nominal bore Make : R.V./Zoloto or equivalent

For pipes of Dia 15 mm

For pipes of Dia 20 mm

For pipes of Dia 25 mm

For pipes of Dia 32 mm

For pipes of Dia 40 mm

UPVC Pipe Type B for Plumbing Providing and Laying Type B UPVC Pipes of any dia (Finolex/ Prince or any other approved equivalent) confirming to IS:13592 including cost of fittings, clamps, consumables, etc. all complete as per drawings, specifications and as per the directions of the Engineer-in-charge

Same as 2070.25.00 but for pipes of Dia 15 mm

Same as 2070.25.00 but for pipes of Dia 20 mm

Same as 2070.25.00 but for pipes of Dia 25 mm

Same as 2070.25.00 but for pipes of Dia 32 mm

Same as 2070.25.00 but for pipes of Dia 40 mm

Brickbat coba- Laying broken pieces of brick, or brickbats, on a flat surface/ sunken area and grouting them with cement to create a waterproof barrier

Polymeric panelling : Double side polymeric partition made out of 250 x 6mm tk. Polymeric panels with tongue and groove joints fixed to the GI grid work with No. 8 x 13 self tapping screw. Color : D51 dotted - white.

Providing and fixing precoated Galvanised PUF insulated sandwich panel corrugated roof sheets (size, shape, colour and pitch of corrugation as approved by Engineer-in-Charge) 50 mm thick panels with U- value (0.43 to 0.46 W/m2.K) and R Value (3.3 m2.K/W) satisfying the specification of ECBC Code (Energy Conservation Building Code) prescribed by Government of India. Panel shall have PPGL sheet on both side of Polyurethane Foam confirming to IS 12436:1988. The pre coated sheet shall be of minimum 550 mpa steel grade confirming to IS 14246:1995 and shall have zinc coating of minimum 120 gsm as per IS :513 : 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 micron. The PPGL sheet should have protective guard film of 25 microns minimum to avoid scratches while transportation and should be supplied in single length upto 12metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55mm) with EPDM seal, complete upto any pitch in horizontal/vertical or curved surfaces excluding the cost of purlins, rafter sand trusses and including cutting to size and shape wherever required as per the directions of EIC. The PU Foam shall be self extinguishing, fire retardant type having minimum density of 40 Kg/Cu.mt (+, -2 Kgs) (Rate will be paid per square metre on superfacial area) including 50mm M20 grade concrete on roof area

Providing and installing prefabricated sandwich PUF wall Panel of 100mm thick, comprising of on two faces PPGL (galvalume) colour coated 0.5mm TCT sheet and CFC free close cell, high density rigid polyurethane foam of high density (40 ± 2 kg/m3) having a thermal conductivity value of 0.023 w/mk and of required thickness sandwiched between the two galvalume sheets. The outer & inner galvalume sheet of 0.50mm TCT steel 550 Mpa shall have a coating mass of 150 g/sqm zinc aluminium alloy coating total of both sides as per AS-1397 and finished with 20 microns colour coating of SMP polyester quality paint as per AS/NZS-2728:1997 (Category-3) over a 5-7 micron epoxy primer and polyester top coat of 15-18 micron on exposed side and a back coat of 5 microns on inner side over a 5-7 micron primer. The panels should be of required length and required width with maximum width up to 1190mm with tongue & groove configuration. The prefabricated panels shall be fixed directly to the girth using self drilling fasteners. The metal sheet shall confirm to IS: 513.AS-1397&2728. The polyurethane insulation shall confirm to IS: 12436. The rate include cost of flashing/ridges/corner pieces/ hips etc. made of 0.5 mm TCT PPGL (Galvalume) steel sheet in required shape and size including all accessories required to complete the work . The rate of the item is inclusive of all materials, likes base channel of required size and shape for seating of wall panels on floor /walls, erection accessories, incidental charges, cost of dash fastners etc, cost of making provision for doors, windows , ventilators, and concealed pipes, conduits and support for electrical and sanitary appliances etc and other incidental charges as per sample including additional flat /sheet of required size, shape and thickness for fixing door/window/ventilator frame complete as per manufacturer’s specification and direction of Engineer-In-Charge . For Wall panels with 100mm thick wall panels finished with 0.50mm thick TCT Galvalume Plain sheet with small ribs on both sides with Camlock arrangement complete including miscellaneous costs of fixing accessories such as wall corners, dash fastners, base channels,nuts and bolts and making arrangement for concealed water supply pipes ,sanitary fittings, electrical appliances and conduits etc. as per direction of Engineer-in-Charge.

Description of Work / Item(s)

Amount

FABRICATION OF PIPING SPECIALS FROM PIPES (SUPPLIED BY OWNER)

PIPING (ABOVE GROUND): Receipt of free issued Materials, transportation of all piping item(s) from Owner's storage point to work site/work shop; fabrication including cutting, edge preparation, (inclusive of grinding the edges of pipe, fittings, flanges, etc. to match with the mating edges of uneven/different thickness wherever required); Locking arrangement for valves, fit up, bending, preheating wherever required, welding, threading, laying of pipes of all types and thickness over sleepers, overhead on racks and at all elevations, scaffolding at all elevation & location, connecting with equipment nozzles, strainers, sight glass, steam traps, expansion bellows, orifice assemblies, spray nozzles, rotameters, tappings for pressure gauges, thermowells, sample connections, springs, sample coolers, pressure relief valves, de-superheater etc. and fixing of gaskets, bolts, nuts including application of torque wherever required & all other inline instruments and fittings , like elbows, reducers, tees, vents, drains, SW/threaded valves up to 1.5 NB, Steam Supply/ Condensate Recovery stations (Cast/ Fabricated), alignment, Fixing and welding of RF pad, cleaning & flushing loop wise and system wise by water/Chemical/compressed air, hydrostatic, pneumatic, vacuum, spark testing , reinstatement, card board blasting, leak test, inertization, hot bolting if required and any other type of testing as specified, draining, drying by compressed air, providing of PMI Machine and performing Positive Material Identification (PMI-077154C-000-JSS-6300-002_0) of existing/new lines using alloy analysers by Level-II qualified NDT Technician, completing all such works in all respects as per the specifications, drawings and instructions of Engineer-In-Charge. Contractor's scope of work includes transportation of fabricated / spooled piping from workshop to work site. Contractor's scope of work includes Preparation of As-built mark up in Isometrics including supports & bill of materials for small bore lines (sizes 1.5” and below). Scope of work Includes Instrument piping hook up items like impulse pipes, fittings etc., from piping isolation valve to instrument shall be fabricated, erected/installed based on the instrument hook drawing and other applicable standards (Instrument Impulse piping and fitting are free issue to contractor)

MOC: CARBON STEEL PIPING (NON IBR)

FABRICATION (BUTT WELD)

Upto 1.5" size and schedule upto 160

From 2" to 6" size and schedule upto 80

From 8" to 14" size and schedule upto 30

From 16" to 24" size and schedule upto 20

FABRICATION (FILLET WELD)

Upto 2" size and schedule upto 160

CARBON STEEL PIPING (IBR)

FABRICATION (BUTT WELD)

Upto 1.5" size and schedule upto 160

Upto 2" size and schedule upto 80

From 3" to 6" size and schedule upto 40

From 8" to 16" size and schedule upto 20

From 2" to 3" size and schedule upto 160

From 4" to 6" size and schedule upto 120

From 8" to 14" size and schedule upto 100

FABRICATION (FILLET WELD)

Upto 2" size and schedule upto 160

MOC - STAINLESS STEEL (ALL GRADES)

FABRICATION (BUTT WELD)

Upto 1.5" size and schedule upto 80S

From 2" to 6" size and schedule upto 40S

From 8" to 14" size and schedule upto 20

FABRICATION (FILLET WELD)

Upto 2" size and schedule upto 80

MOC - GALVANIZED - Cold galvanizing spray to be applied on welded joints

FABRICATION (BUTT WELD)

From 3" to 6" sizes

From 8" to 14" size

FABRICATION (FILLET WELD)

Upto 2" size

MOC - HDPE

Upto 1.5" size

From 2" to 6" size

ERECTION

MOC - CARBON STEEL NON IBR

Upto 2" size

From 3" to 6"

From 8" to 14"

From 16" to 24"

MOC - CARBON STEEL IBR

Upto 2" size

From 3" to 6"

From 8" to 14"

From 16" to 24"

MOC - STAILESS STEEL (ALL GRADES)

Upto 2" size

From 3" to 6"

From 8" to 14"

MOC - GALVANIZED CARBON STEEL PIPING

Upto 2" size

From 3" to 6"

From 8" to 14"

FABRICATION OF UNDER GROUND PIPING SPECIALS FROM PIPES (SUPPLIED BY OWNER)

PIPING (UNDER GROUND):Receipt of free issued Materials, transportation of all piping item(s) from Owner's storage point to work site/work shop; fabrication including cutting, edge preparation, (inclusive of grinding the edges of pipe, fittings, flanges, etc. to match with the mating edges of uneven/different thickness wherever required); Locking arrangement for valves, fit up, bending, preheating wherever required, welding, and laying of pipes of all types and thickness and fixing of gaskets, bolts, nuts including application of torque wherever required & elbows, reducers, tees, vents, drains, SW/threaded valves up to 1.5 NB, alignment, Fixing and welding of RF pad, cleaning & flushing loop wise and system wise by water/Chemical/compressed air, hydrostatic, pneumatic, vacuum, spark testing , reinstatement, leak test, inertization, if required and any other type of testing as specified, draining, drying by compressed air completing all such works in all respects as per the specifications, drawings and instructions of Engineer-In-Charge. Contractor's scope of work includes transportation of fabricated / spooled piping from workshop to work site. Contractor's scope of work includes Preparation of As-built mark up in Isometrics including supports & bill of materials for small bore lines (sizes 1.5” and below). Scope of work Includes Instrument piping hook up items like impulse pipes, fittings etc., from piping isolation valve to instrument shall be fabricated, erected/installed based on the instrument hook drawing and other applicable standards (Instrument Impulse piping and fitting are free issue to contractor). Scope includes excavation, preparation of sand bed (including supply of sand), laying of piping as per drawings, wrapping & coating of field welded locations and repair of original coating where ever damaged, carrying out holiday testing, back filling of soil & compaction.

MOC - HDPE

Upto 2" size

From 3" to 6"

MOC - CARBON STEEL NON IBR

Upto 2" size

From 3" to 6"

From 8" to 14"

Valves /Flowmeters- Installation of all types of valves and other in-line items

All types of Falnged Valves Including Special Valves, MOV, Control and ON-OFF valves - rating upto 600#

NB 2.00 INCHES

NB 3.00 INCHES

NB 4.00 INCHES

NB 6.00 INCHES

NB 8.00 INCHES

NB 10.00 INCHES

NB 12.00 INCHES

NB 16.00 INCHES

All types of Falnged Valves Including MOV, Control and ON-OFF valves - rating above 600#

NB 0.75 INCHES

NB 1.00 INCHES

NB 1.50 INCHES

NB 2.00 INCHES

NB 3.00 INCHES

NB 4.00 INCHES

NB 8.00 INCHES

All types of flanged in-line items like Strainers ,Traps, Sight Glass Flow Indicators, Expansion Bellows, Rupture Discs etc.. of any size and rating

Size Upto 1.5 Inches

Size 2 Inches

Size 4 Inches

All types of Falnged Valves Including Special Valves, MOV, Control and ON-OFF valves - rating upto 600#

NB 0.50 INCHES

NB 0.75 INCHES

NB 1.00 INCHES

NB 1.50 INCHES

NB 2.00 INCHES

NB 3.00 INCHES

NB 4.00 INCHES

NB 6.00 INCHES

NB 8.00 INCHES

NB 10.00 INCHES

NB 12.00 INCHES

NB 14.00 INCHES

NB 16.00 INCHES

NB 18.00 INCHES

NB 20.00 INCHES

NB 24.00 INCHES

NB 28.00 INCHES

NB 30.00 INCHES

NB 32.00 INCHES

NB 36.00 INCHES

NB 104.00 INCHES

All types of Falnged Valves Including MOV, Control and ON-OFF valves - rating above 600#

NB 1.00 INCHES

NB 1.50 INCHES

NB 2.00 INCHES

NB 3.00 INCHES

NB 4.00 INCHES

NB 6.00 INCHES

NB 8.00 INCHES

NB 10.00 INCHES

NB 12.00 INCHES

NB 16.00 INCHES

NB 18.00 INCHES

NB 20.00 INCHES

NB 28.00 INCHES

All types of Inline instruments Including Coriolis, Vortex, Magnetic Flowmeters - rating upto 600#

NB 0.75 INCHES

NB 1.00 INCHES

NB 1.50 INCHES

NB 2.00 INCHES

NB 3.00 INCHES

NB 4.00 INCHES

NB 6.00 INCHES

NB 8.00 INCHES

NB 10.00 INCHES

NB 12.00 INCHES

NB 14.00 INCHES

NB 16.00 INCHES

NB 20.00 INCHES

Rating upto 600#

UP TO NB 1.50 INCHES

FROM 2.00 INCHES TO NB 4.00 INCHES

FROM 6.00 INCHES TO NB 8.00 INCHES

FROM 10.00 INCHES TO NB 12.00 INCHES

FROM 12.00 INCHES TO NB 16.00 INCHES

Rating upto 600#

UP TO NB 1.50 INCHES

FROM 2.00 INCHES TO NB 4.00 INCHES

FROM 6.00 INCHES TO NB 8.00 INCHES

FROM 10.00 INCHES TO NB 12.00 INCHES

FROM 12.00 INCHES TO NB 16.00 INCHES

PIPE SUPPORTS FOR C.S (INCLUDING MATERIAL SUPPLY): NFIM

Supply, Fabrication, erection (at all elevations) of Pipe Supports like Shoes, Cradles, Hangers, Clamps, U-Bolts, Turn Buckles, Saddles, Guides, Special Supports, T Post, Brackets etc. of all types including supply and application, shot blasting, one coat of primer, intermediate & final paint as per the painting specification, all necessary equipment, consumables, labour, and completing work as per drawings, specifications and instructions of Engineer-in-charge. Modifications/rectifications, if required; and adjustments/alignment during pre-commissioning, commissioning as per the instructions of Engineer-in-charge. The scope of Works also includes grouting of supports, if required as part of Pipe Supports Works within the quoted price which includes supply of grouting materials also and nothing extra shall be payable in this regard. While fabricating the supporting elements the Contractor will ensure that dimensions shown in the drawings match with the site conditions. Welding of Pipe supports with corrosion Pad and Trunnion welding in Contractor scope. Additional supports as necessary with the site condition shall be fabricated and erected in accordance with the Standard. The measurement shall be done in MT of finished support. Wastage shall not be considered. Scope also includes providing all the tools & tackles, machineries, Man lift, consumables, steel scaffolding at all location and all elevation, manpower, PPE, supervision, etc.

Pipe Supports -Carbon steel

Pipe Supports -Stainless Steel

PIPE SUPPORTS (FROM MATERIALS SUPPLIED BY OWNER): FIM

Fabrication, erection (at all elevations) of Pipe Supports like Shoes, Cradles, Hangers, Clamps, U-Bolts, Turn Buckles, Saddles, Guides, Special Supports, T Post, Brackets etc. of all types including supply and application, shot blasting, one coat of primer, intermediate & final paint as per the painting specification, all necessary equipment, consumables, labour, and completing work as per drawings, specifications and instructions of Engineer-in-charge. Modifications/rectifications, if required; and adjustments/alignment during pre-commissioning, commissioning as per the instructions of Engineer-in-charge. The scope of Works also includes grouting of supports, if required as part of Pipe Supports Works within the quoted price which includes supply of grouting materials also and nothing extra shall be payable in this regard. While fabricating the supporting elements the Contractor will ensure that dimensions shown in the drawings match with the site conditions. Welding of Pipe supports with corrosion Pad and Trunnion welding in Contractor scope. Additional supports as necessary with the site condition shall be fabricated and erected in accordance with the Standard. The measurement shall be done in MT of finished support. Wastage shall not be considered. Scope also includes providing all the tools & tackles, machineries, Man lift, consumables, steel scaffolding at all location and all elevation, manpower, PPE, supervision, etc.

Pipe Supports -Carbon steel

Pipe Supports -Stainless Steel

PAINTING OF PIPING

Supply of paints and primers, preparation of surfaces and application of primer, intermediate and finish paints, identification (Line numbering), lettering, colour bands, colour coding etc. as specified including rubdown and touch up of shop primer wherever required, providing scaffolding for all heights, labour, material, tools and tackles, consumables supervision etc. to complete the work in all respects as per Technit painting job specification OSBL-0814-0000-JSD-2300-001_1, drawings and direction of Engineer-in-Charge for all types of uninsulated piping and insulated piping as specified including all pipes, fittings, flanges, supports, valves etc. Surface preparation by blast cleaning and application of first coat of primer (Ethyl Zinc Silicate) shall be done in fabrication yard prior to erection. For insulated piping wherever blast cleaning with no primer application is specified, in such cases finish paints shall also be applied in the fabrication yard. The identification marks of the piping and joints shall be noted before blasting and the same shall be transferred on primed surface with Polyurethane paint or as per the instructions of Engineer-in-Charge. Notes: 1. All joints (fabrication as well as erection joints) shall be left unpainted till hydrotesting. 2. No extra payment shall be made for identification (line numbering etc.) of insulated and uninsulated lines. SURFACE PREP, PRIMER & FINISH COAT FOR CS BARE SURFACES FOR HIGHLY CORROSIVE - INDUSTRIAL ENVIRONMENT AS PER PAINTING JOB SPECIFICATION "OSBL-0814-0000-JSD-2300-001_1"

Paint system A1 up to 100 Deg C, CS Uninsulated: Uninsulated Carbon Steel & Low Alloy Steel Painting of Rotary / Static equipment, Piping and Piping Supports at any height, SURFACE PREPARATION: Surface preparation by abrasive blasting cleaning to Grade SA 2.5 minimum / SSPC-SP-10 Primer: Zinc Inorganic Solvent Born (ESI: Ethyl Zinc Silicate, Coat Thickness: DFT- 60 micron average) + Intermediate: Epoxy MIO (EP-MIO: 2-Pack Epoxy Pigmented with Micaceous Iron Oxide, Coat Thickness: DFT - 165 micron average) + Finish: Polyurethane (PUR: 2-Pack Acrylic Polyurethane, Two Coats (DFT- 40μ/coat average) Coat Thickness: DFT - 75 micron average). TOTAL FINAL DFT 300 micron average

Paint system A2 101 Deg C up to 400 Deg C, CS Uninsulated and Insulated: Uninsulated and Insulated Carbon Steel & Low Alloy Steel Painting of Rotary / Static equipment, Piping and Piping Supports at any height, SURFACE PREPARATION: Surface preparation by abrasive blasting cleaning to Grade SA 2.5 minimum / SSPC-SP-10 Primer: Zinc Inorganic Solvent Born (ESI: Ethyl Zinc Silicate, Coat Thickness: DFT- 60 micron average) + Intermediate: Single Pack Silicon based (SYL: Heat resistance silicone Aluminium paint suitable up to 500 deg C dry temperature or MFR STD, Coat Thickness: DFT 25 micron average) Finish: Single Pack Silicon based (SYL: Heat resistance silicone Aluminium paint suitable up to 500 deg C dry temperature or MFR STD, Coat Thickness: DFT 25 micron average) TOTAL FINAL DFT 110 micron.

Paint system A3 up to 100 Deg C, CS Insulated: Insulated Carbon Steel & Low Alloy Steel Painting of Rotary / Static equipment, Piping and Piping Supports at any height, SURFACE PREPARATION: Surface preparation by abrasive blasting cleaning to Grade SA 2.5 minimum / SSPC-SP-10 Primer: Epoxy Phenolic Coating (EPFTwo pack cold cured epoxy phenolic coating suitable for -45 Deg C to m150 Deg C for application under insulation), Coat Thickness DFT per Coat 75 micron average, Required Coat Thickness: DFT 150 micron average + Intermediate: Epoxy Phenolic Coating (EPFTwo pack cold cured epoxy phenolic coating suitable for -45 Deg C to m150 Deg C for application under insulation), Coat Thickness DFT per Coat 75 micron average, Required Coat Thickness: DFT 150 micron average. TOTAL FINAL DFT 300 micron.

Mechanical Anchor Fastners

Supplying, handling, transporting to site of work and fixing of approved MECHANICAL ANCHOR FASTENERS M.S.bolts of Grade 5.8 or more, GALVANIZED with minimum thickness of 5 microns (approved for use in cracked concrete), of 12mm dia at specified positions on concrete floors, roofs, beams (sides and bottom), walls, columns etc. according to manufacturer's specifications including all accessories like nuts, washers etc. of required size, testing, necessary scaffolding, drilling of the holes in concrete surface with electric drill, cleaning of holes with air blowout & wire‐brush, and making good any damage done to the structure etc. all complete for all heights,depths and locations as specified and directed.

Bolt Size 12mm (Hilti make)

Bolt Size 16mm (Hilti make)

U Clamps / Bolts of all sizes GI/SS as per Specification

NON DESTRUCTIVE TESTING

RADIOGRAPHY: Performance of radiographic inspection on piping of all types & thickness including providing or hiring of all necessary equipment and whatever else even though not explicitly mentioned but required to perform the work as per specifications and instructions of Engineer-in-charge. Rates are inclusive of radiography machine, work force, consumables etc. and all other equipment required to perform the radiography at all heights including staging Scaffolding to the satisfaction of Engineer-in-charge. Radiographs shall be submit to the Engineer-in-charge. (Repeat Radiography due to defective radiograph on repaired joints due to Contractor's fault and for additional radiography necessitated due to poor performance of contractor's welders shall be done at contractor's cost and nothing shall be paid as extra). Scope also includes providing all the tools & tackles, machineries, Man lift, consumables, steel scaffolding at all location and all elevation, manpower, PPE, supervision, etc. Note: Unit for radiography quantity is "Nos" for Pipe NB Size <=2" and Inch Dia for Pipe NB Size above >2".

Film Radiography by X Rays / Gamma Rays Pipe NB Size <=2"

Film Radiography by X Rays / Gamma Rays Pipe NB Size above >2"

Radiography using Closed Proximity Test Gamma Ray - Selenium (Se 75)-SAFE RAD source

DYE PENETRATION/ MAGNETIC PARTICLE TEST : - Performance of Magnetic particle/ dye penetrant test including supply of all necessary materials; equipments and labour for carrying out the work as per specification and directions of Engineer-in-charge.

DYE PENETRATION TEST

MAGNETIC PARTICLE TEST

POST WELD HEAT TREATMENT (PWHT)

Perform Post Weld Heat Treatment of a weld, by electrical means or of a batch of piping in a furnace including necessary handling and transportation of Pipe Spools, hardness testing, evaluation, administration and reporting. The rate includes charges for all Labour force, Equipment, Consumables, and all other items required for the complete execution of the work.

Carry out Preheat, post heat and stress relieving (PWHT) as per specification

Carry out COLD HARDNESS of welded joints and parent materials

External Chemical Cleaning and Passivation of SS Welds and fittings of Tanks and pipes as per Job Specification, Doc. No. B297-000-06-41-CCS-011 and instructions of Engineer-in-charge.

Carry out passivation of all welded joints - All grades of SS

PMI of welded joints and parent materials (Inclued in Piping fabrication SOR)

Perform field Positive Material Identification (for specific materials), by deploying necessary equipment / manpower / Inst. / tools etc.. The rate includes necessary handling and transportation of Piping items / Spools,/ valves etc. including scaffolding and making access to the joints PMI testing, evaluation, administration and reporting in accordance with the specification.

Fabrication, Erection, Dismantling and returning of temporary piping

Shifting / transporation of all FIM from store / warehouse to fabrication yard, fabrication, erection in field / wherever required at all elevations including welding, builtup & dismantling of scaffolding and erection of flanged vales if any as per instruction of EIC, modifying erected piping,dismantling, returning back all usable materials to owner (duly bevelled at both ends). Providing temporary insulation (only lagging) wherever required and it's removal & Disposal. Preparing hand sketches. Returning all scrap materials to designated place as per instruction of EIC. All welding should be carried out as per approved WPS

From 8" to 14"

16" and above

MODIFICATION/EXTRA WORKS

MODIFICATION/EXTRA WORKS (IF ANY): Cutting, bevelling, fitup, welding of different sizes of CS/AS/SS/Higher Alloy piping of all types and thicknessess in fabrication shop, in position, on ground/overhead on rack and at all elevations; transportation of pipes, fittings, flanges etc from owner's storage point to work site/ work shop, making necessary scaffoldings, consumables, machinery, tools, tackles, labour and supervision including attending repairs for completing the work as per the instruction of Engineer-in-charge.

FLAME CUTTING C.S PIPING IBR/NON IBR

HACKSAW CUTTING C.S PIPING IBR/NON IBR

BEVELLING C.S PIPING IBR/NON IBR

FITUP & WELDING C.S PIPING IBR/NON IBR

FLAME CUTTING S.S PIPING IBR/NON IBR

HACKSAW CUTTING S.S PIPING IBR/NON IBR

BEVELLING S.S PIPING IBR/NON IBR

FITUP & WELDING S.S PIPING IBR/NON IBR

REMOVAL ERECTED PIPING (ABOVE GROUND)

Removal of piping existing/ erected including SW valves for modification as required as per Drawings/P&IDs/instructions of Engineer-in-charge at all elevations, including providing assistance to owner for draining, cleaning and purging of the lines to be removed , unbolting of flanged joints /cutting of pipe lines wherever required, installation of flanges and blind flanges, removal of insulation from insulated lines, removing supports, steam tracers, all fittings and flanges, instruments etc, cutting of pipes in appropriate length for transporting purposes, cleaning, flushing, drying and transporting all materials to storage point(within the complex battery limits) designated by Owner/EIL including stacking of material and disposing of waste etc as instructed by Engineer-in-charge.

ALL TYPE C.S/A.S PIPING

ALL TYPE S.S PIPING

HOOK UP CONNECTIONS WITH EXISTING LINES ISBL & OSBL (IBR/ NON-IBR) :

The Contractor's scope for Hook up connections with existing lines (irrespective of size) as per process requirements/ hook up Sketches /Piping GADs in the existing Offsite areas & Process unit areas. It shall include transportation of all piping materials & all other free issue materials (FIM)from owner's storage point to work site/shop including raising store requisitions for issue of material in the prescribed format & maintaining an account of the materials received from owner's stores & reconciliation of all Owner supplied free issue materials (FIM), Fabrication of plain & threaded nipples from pipes, stub in connections with or without reinforcement, including supply of all consumables, supply of necessary materials, providing support for new piping, modified piping, change of existing supports / additional supports in existing piping as indicated in the Drawings or as required by the Engineer-in-charge. Contractor Scope includes Pre-fabrication, cutting, welding in existing lines. Contractor scope also includes erection of valves with Flange and Blind flange, statutory approval of piping wherever required, obtaining hot work permit from the client, fabrication including cutting, edge preparation (inclusive of grinding the edges of pipe, fittings, flanges etc. to match the mating edges of uneven/ different thickness wherever required), fit-up, preheating wherever required, welding, laying, erection, supporting, cleaning & flushing by water/compressed air, non-destructive testing, positive material identification, hydrostatic test, pneumatic test or any other type of test as specified, draining, drying by compressed air, bolt torquing, flushing (including steam flushing), complete in all respects at all elevations (providing scaffolding/ platforms as per requirement), of all piping required for successful erection & testing , providing lifting tools/ tackles, all normal & special equipment & gadgets, skilled/unskilled labor, specialists, supervisory staff, as per the standards, specification, approved drawings and provision of local barricading/ blanketing at hot work permit area at all levels and elevations as per safety measures & instructions of Engineer-in-charge.

For cooling water hook-ups & Fire water hook-ups Rates shall be inclusive of Excavation, Underground Tap-off & suitable wrapping and coating (as per applicable standard) for underground portion of lines. Rates for each Hook up point also shall be inclusive of 100% radiography in case of all butt welded joint & 100% DP/MP test in case of all fillet welded joints with hook-up complete in all respect as per Hook-up Isometrics. Sourcing of materials for hook-ups based on site data / information and checking for Hook-ups feasibility, removing & restoration of insulation of existing line where hook- ups will be executed. For IBR line/ hook ups, contractor to make required GADs/ Isometrics as required by local IBR authority to obtain approval. Sizes provided are of branch connection. Payment shall be made based on size of branch. Contractor to ensure the availability of latest Hook-up Isometrics before going for Execution.

Installation of pre-fabricated hook-ups on the line: Welding of first joint of pre- fabricated hook-ups on pipe/ equipment/ orifice flange/ flow-meter end, welding of end connection on tapping/ pre-fabricated hook-ups, seal run of threaded connection including erection of supports, performing positive material identification (PMI) using alloy analyzers and performing radiography on all welds. PWHT to be done wherever applicable, as per the piping class. Transportation of all items from owner's storage point to work site/ workshop. Welding/ fixing of pipe clamps, instrument stanchion. Pre-Fabricated hook-up welding on pipe shall be of dissimilar material. Material of Pre-fabricated hook-ups shall be -------

EQUAL SIZES (CARBON STEEL) RATING 150# TO 600#

NB 2.000 INCHES

NB 3.000 INCHES

NB 4.000 INCHES

NB 6.000 INCHES

NB 10.000 INCHES

UNEQUAL SIZES (STAINLESS STEEL) RATING 150# TO 600#

NB 2.000 INCHES

NB 3.000 INCHES

NB 4.000 INCHES

HOT INSULATION (UNITS)

HOT INSULATION (UNITS) ; Providing thermal insulation including supply of all insulating and ancillary materials, vapour barrier, weather protective coverings, consumables and other necessary materials , testing of materials as required, including transportation of materials to work site, duly inspected by 3rd party inspector(Llyods/BV/DNV or any other Client approved party) at manufacturer's shop & sample check/inspection at site by Construction inspector, applying insulation on surfaces as specified including all preparatory work there on, binding, tying, lacing, stitching and/or otherwise securing , finishing with sheet cladding as per spec. , providing bolts, rivets, and self tapping screws wherever specified , providing inspection windows, end seals for flanges etc., colour coding and identification. Providing steel scaffolding, all tools , tackles , equipments etc. , labour, supervision and completing the work in all respect, at all heights as per drawings , specifications (2450-0000-JSD-2200-01, Rev-01)

INSULATION TYPE : IH; SURFACE MATERIAL : CS & AS; OPERATING TEMP. RANGE : UPTO 125 (DEG C)

For Pipes, Flanges, Valves and Equipment if any

INSULATION TYPE : IH; SURFACE MATERIAL : CS & AS; OPERATING TEMP. RANGE : 126 (DEG C) TO 350 (DEG C)

For Pipes, Flanges, Valves and Equipment if any

INSULATION TYPE : IH; SURFACE MATERIAL : CS & AS; OPERATING TEMP. RANGE : 351 (DEG C) TO 500 (DEG C)

For Pipes, Flanges, Valves and Equipment if any

Description of Work / Item(s)

Amount

EQUIPMENT - ROTARY

EQUIPMENT ERECTION ON NEW FOUNDATION

SYSTEM 6850 - ERECTION OF MACHINERY (SUPPLIED BY OWNER)

MACHINERIES WITH DRIVERS ON FRAME

Machineries with drivers (in single piece) (LS)

Equipment Weight Up to 2 MT (As listeed Below) 'Acetic Acid unloading Pump (BG-704A)' 'Acetic Acid unloading Pump (BG-704B)' 'Acetic Acid Storage Tank Transfer Pumps (BG-705A)' 'Acetic Acid Storage Tank Transfer Pumps (BG-705B)' 'Steam Turbine for BFW Pump' 'Steam Turbine for BFW Pump - Lube Oil System' 'GEAR BOX FOR for BFW Pump' 'STEAM TURBINE (BCT-920C)' 'STEAM TURBINE (BCT-920D)' 'STEAM TURBINE (BCT-921C)' 'STEAM TURBINE (BCT-921C)' 'GEAR BOX FOR STEAM TURBINE (BCT-920C)' 'GEAR BOX FOR STEAM TURBINE (BCT-920D)' 'GEAR BOX FOR STEAM TURBINE (BCT-921C)' 'GEAR BOX FOR STEAM TURBINE (BCT-921D)' 'NaOH pump, BG-1246 G' 'NaOH pump, BG-1246 H' 'Foam Pump' 'WWTP pumps suction Poly Propylene flanged-end foot valves' 'Future Pump - 1' 'Future Pump - 2'

Equipment WeightAbove 2 MT and up to 5 MT (Equipment list as below) 'OTHERS ROTARY EQUIPMENT - 1' 'OTHERS ROTARY EQUIPMENT - 2' 'OTHERS ROTARY EQUIPMENT - 3'

Equipment Weight Above 5 MT up to 10 MT (Equipment list as below) 'Paraxylene Booster Pumps (BG-030A)' 'Paraxylene Booster Pumps (BG-030B)' 'Paraxylene Booster Pumps (BG-030C)' 'ID FANS (BC-920C)' 'ID FANS (BC-920D)' 'FD FANS (BC-921C)' 'FD FANS (BC-921D)' 'Paraxylene Transfer Pump (CG-210C)' 'Paraxylene Transfer Pump (CG-210D)' 'Future Equipment -1'

EQUIPMENT - STATIC

EQUIPMENT ERECTION ON NEW FOUNDATION

In case of equipment directly reaching at Project erection site by Transporter Truck / Trailer, in that case unloading at site for erection Works is in the scope of Contractor within the quoted Price for equipment erection. Depressurization of Nitrogen from New equipment supplied by Vendor is also in the scope of Contractor. After erection of the equipment or stacking at any location at site, equipment must be under preserved condition i.e. nitrogen gas purging and maintenance of Nitrogen pressure in contractor scope until commissioning of the equipment. Nitrogen shall be provide by GMPL at plant B/L however, contractor have to made arrangement for filling from provided point. During the erection and alignment of the equipment, any minor alteration in other than pressure part if need to be carried out shall be done by contractor scope as per guidelines by engineer-In-charge.

Scaffolding: Contractor to prepare the erector plan in order to finalize the requirement of Scaffolding for erection of all the Equipment. Erection contractor to perform scaffolding for erection of all the external attachments like platform installation, ladder installation, insulation installation & Fireproofing, etc. Cost for the scaffolding to be included in Contractor scope. All necessary tools, tackles & machineries, work force, cranes, etc. are to be arrange by contractor. Any additional requirement of scaffolding for any of the activities like blinding, de-blinding, etc. until commissioning is included in Contractor's scope. Cost of these scaffolding is included in the base Quote. No additional payment will be provided to Contractor.

SYSTEM 6820 - ERECTION OF VERTICAL AND/OR HORIZONTAL STATIC EQUIPMENT

ERECTION OF STATIC EQUIPMENT (VERTICAL/HORIZONTAL) (LS)

Static Equipment Erection upto 10 MT (Equipment list as follows) Silencer - BH-910A Silencer - BH-913 Silencer - BH-914 Fuel Gas Knock Out Drum, BD-1172 Foam Tank Overhead Foam Tank, 25 KL Cap -1 Overhead Foam Tank, 25 KL Cap - 2 Plate Heat Exchanger CE-269 Belt filter press BM-1246

EQUIPMENT - PACKAGES

SYSTEM 6880 - ERECTION OF PACKAGES AND OTHER EQUIPMENT

OTHER EQUIPMENT (to be assembled by bolting) (LS) (Product loading arms with movable joints, with flanged or threaded connections for piping and/or equipment; volume indicators with flanged and/or threaded ends, ejectors, flanged and/or threaded Venturi meters, blade mixers or others, to be erected with stirrups or flanges, etc). - Unloading at the arrival at Site, storage (if necessary), transportation and handling at Site, - Erection on foundations or on structures at any height and at any plant location, elevation/layout adjustment, leveling, assembly of the various parts. - Assembling by bolting, without particular alignment requirements, - Erection of all accessories belonging to the supply - Inspection and tests

WWTP-PACKAGE BOILER (12T)

EQUIPMENT - PACKAGES

SYSTEM 6880 - ERECTION OF PACKAGES AND MISCELLANEA MATERIAL

OTHER EQUIPMENT (to be assembled by bolting) (LS) (Product loading arms with movable joints, with flanged or threaded connections for piping and/or equipment; volume indicators with flanged and/or threaded ends, ejectors, flanged and/or threaded Venturi meters, blade mixers or others, to be erected with stirrups or flanges, etc). - Unloading at the arrival at Site, storage (if necessary), transportation and handling at Site, - Erection on foundations or on structures at any height and at any plant location, elevation/layout adjustment, leveling, assembly of the various parts. - Assembling by bolting, without particular alignment requirements, - Erection of all accessories belonging to the supply - Inspection and tests

Other equipment (to be assembled by bolting) (LS)

Drinking Water Package

EOT Crane Main Assembly along with its accessories including Commissioning as folllows: 'EOT Crane Main Assembly along with its accessories including Commissioning - BM – 051' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM – 060' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM – 061' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM – 071' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM – 072' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM – 064' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM – 067' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM – 068' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM – 069' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM – 070' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM - 055' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM - 054' 'EOT Crane Main Assembly along with its accessories including Commissioning - BM - 053'

Natural Gas Skid

Dock Leveller Details are af follows Dock Leveller - 1 Dock Leveller - 2 Dock Leveller - 3 Dock Leveller - 4 Dock Leveller - 5

Monorail type Chain Pulley block - Capacity upto 10 MT

Weigh Bridge

PACKAGED MACHINERY (LS) (Equipment delivered in few pre-assembled skids, such as: Reciprocating screws, centrifugal mixers, weighing machine units, bagging machines, palletizers, conveyor belts) - Unloading at the arrival at Site, storage (if necessary), transportation and handling at Site, - Preparation of foundation, including installation of shimming plates, - Erection on foundations or on structures at any height and at any plant location, elevation/layout adjustment, levelling, assembly of the various parts - Assembling by bolting, without particular alignment requirements, - Erection of all accessories belonging to the supply - Inspection and tests

Packaged machinery (LS) (equipment delivered in few pre-assembled skids)

Bagging Machines Weight 8T

Bagging Machine - Integration/ Conveying System Weight=3T

ASMR Weight=TBCT

Foam Generator Weight=2.5T

EDG Weight=15T

ROPW dosing package Weight=TBCT

WASTE WATER TREATMENT UNIT (LS) - Unloading at the arrival at Site, storage (if necessary), transportation and handling at Site, - Erection on foundations or on structures at any height and at any plant location, of the skids/components of the “unit” - Preparation of foundation, including installation of shimming plates, - Elevation/layout adjustment, leveling of skids/components of the unit - Assembly and erection of the "unit" components supplied loose such as steel structures, small complexes of vessels, machines, piping, heat exchangers, filters or other equipment assembled together on a supporting frame or plate (skids), with verification and correction of alignments where necessary - Erection of prefabricated piping belonging to any package complex, which, for shipping purpose has been disassembled, shall be paid at the same erection price as the whole complex. - Erection of lubrication oil consoles for large machinery, even if the said consoles are supplied with the machines themselves. - Erection of all other components and accessories belonging to the supply (including filling/inert materials) - Inspection and tests

Supply of Spark Resistant Chain Pulley Block with or witout Geared Trolley

1 No. x 2 MT (Safe Working limit) (height of lift range (3-10)m)

1 No. x 3 MT (Safe Working limit) (height of lift range (11-17) m)

1 No. x 10 MT (Safe Working limit) (height of lift : 7m)

Description of Work / Item(s)

Amount

Receipt of materials from OWNER's store / yard / storage point, loading on truck / trailer, Transportation of Equipment & Associated items, unloading at site, preparation of erection scheme for approval, carrying out necessary drilling/machining, if required, enlarging of coupling bores, assembly of subassemblies, placing the equipments on foundations at all heights and locations,including SPARES as per equipment list ,supplying and fixing of nuts, bolts, washers, gaskets (as per specs.) needed for fixing the equipment with matching flange etc., testing, Unloading of Materials, Material inspection,Storing of materials at Contractor store with proper preservation at site as per vendor recommendation. etc. Description of the equipment are as per document no : 0814-B000-NM-1900-002.

Installation of High Volume Long Range Water Cum Foam Monitor 1000GPM, UL /FM approved. Variable flow type. ( supply by GMPL )

Installation of High Volume Long Range Water Monitor 1000GPM, UL /FM approved. ( supply by GMPL )

Supply ,Installation, connection, testing and commissioning of various firefighting items as per the specifictaions

Supply & Installation of Double headed stand post type Fire hydrant valves

Stand post without Pumper Connection - 4" - Carbon steel

Stand post with Pumper Connection - 4" - Carbon steel

Hydrant valves-as per IS:5290, Type A

Supply & Installation of Hose Box-External (Size-750mm x 600mm x 250mm (Minimum) - Mild Steel - 18 SWG, Double Panel Glass Door (3mm thickness) with standard Mortise type Lock, MS Hammer with GI Chain, Mounting Shall be Self Supported type suitable for outside/inside installation.

Supply & Installation of Fire Hose with Couplings 63 NB 15 mtrs Long Non-percolating synthetic Hose as per IS 636 Type B with male/female Instantaneous spring lock type coupling 63NB at both ends as per IS 903.

Supply & Installation of Fast action nozzle/Triple Purpose Nozzle - as per IS:2871-63NB size (fog / jet spray type)

Spanner

Supply & Installation of Landing valves for Single Headed Fire Hydrant at technological structures

Hydrant valves-as per IS:5290, Type A

Hose Reel – Wall-mounting Type for Technological structures and building-as per IS:884

Air Release Valve, as per IS-778

Supply & Installation of Water spray Nozzles - 1/2“ NPT (M) UL/ FM Approved

Medium Velocity Water Spray Nozzles - Forged brass IS 291, Gr-1

K factor-22 & Angle-120

K factor-79 & Angle-120

ISBL area K-factor-51 & Angle-140

High Velocity Water Spray Nozzles

K factor-22 & Angle-120

K factor-18 & Angle-120

Supply & Installation of Quartzoid Bulb Detector - Thermo sensitive bulb - 68 Deg, 1/2" NPT (M), UL listed & FM approved, K-Factor 80 metric.

Supply & Installation of Alarm Valve and acessories - 8"

Supply & Installation of Sprinkler nozzle (Early suppression fast response, Upright, K-240)

Supply & Installation of First-Aid Fire Fighting Equipment

Portable Dry Chemical Powder Extinguisher (ABC Type) – 9 kg - Stored pressure type

Portable Dry Chemical Powder Extinguisher (ABC Type) – 6 kg - Stored pressure type

Wheeled Dry Chemical Powder Extinguisher (BC Type) – 25 kg - Trolley mounted Cartridge operated

CO2 Fire Extinguisher (4.5 Kg)

CO2 Fire Extinguisher (6.8 Kg)

Sand Buckets

Supply & Installation of Safety shower & Eye wash station

Description of Work / Item(s)

Amount

Scope of work includes Supply of Cables as per requirement mentioned

SUPPLY OF - 1P, Copper wire, stranded, 1.5 mm²,armoured, Intrinsic safe,Flame Retardant

SUPPLY OF - 1P, Copper wire, stranded, 1.5 mm²,armoured, Non Intrinsic safe,Flame Retardant

SUPPLY OF - 2P, Copper wire,stranded, 1.5 mm²,armoured, Intrinsic safe, Flame Retardant

SUPPLY OF - 1T, Copper wire,stranded, 1.5 mm²,armoured, Non Intrinsic safe, Flame Retardant

SUPPLY OF - 6P, Copper wire,stranded,0.75 mm²,armoured, Intrinsic safe, Flame Retardant

SUPPLY OF - 6P, Copper wire,stranded,0.75 mm²,armoured, Non Intrinsic safe, Flame Retardant

SUPPLY OF - 6P, Copper wire,stranded,0.75 mm²,armoured, Non Intrinsic safe, Fire resistant

SUPPLY OF - 12P, Copper wire,stranded,0.75 mm²,armoured, Non Intrinsic Safe , Flame Retardant

SUPPLY OF - 1T, Copper wire,stranded, 1.5 mm²,armoured, Non Intrinsic safe, Fire Resistant

SUPPLY OF - 12T, Copper wire,stranded,1.5 mm²,armoured, Non Intrinsic safe, Fire Resistant

SUPPLY OF - 6T, Copper wire,stranded,1.5 mm²,armoured, Intrinsic safe, Flame Retardant

SUPPLY OF - 6T, Copper wire,stranded,1.5 mm²,armoured, Non Intrinsic safe, Fire Resistant

SUPPLY OF - 8T, Copper wire,stranded, 1.5 mm²,armoured, Non Intrinsic safe, Flame Retardant

SUPPLY OF - 12P, Copper wire,stranded,0.75 mm²,armoured, Non Intrinsic safe, Fire Resistant

SUPPLY OF - Power cable -3C X 2.5mm2,armoured, Non Intrinsic safe, Flame Retardant

SUPPLY OF - Power cable, 3CX 2.5 mm²,armoured, Non Intrinsic safe, Fire resistant

SUPPLY OF - Power cable, 3CX 6 mm²,armoured, Non Intrinsic safe, Fire resistant

INSTALLATION OF - 1P, Copper wire, stranded, 1.5 mm²,armoured, Intrinsic safe,Flame Retardant

INSTALLATION OF - 1P, Copper wire, stranded, 1.5 mm²,armoured, Non Intrinsic safe,Flame Retardant

INSTALLATION OF - 2P, Copper wire,stranded, 1.5 mm²,armoured, Intrinsic safe, Flame Retardant

INSTALLATION OF - 1T, Copper wire,stranded, 1.5 mm²,armoured, Non Intrinsic safe, Flame Retardant

INSTALLATION OF - 6P, Copper wire,stranded,0.75 mm²,armoured, Intrinsic safe, Flame Retardant

INSTALLATION OF - 6P, Copper wire,stranded,0.75 mm²,armoured, Non Intrinsic safe, Flame Retardant

INSTALLATION OF - 6P, Copper wire,stranded,0.75 mm²,armoured, Non Intrinsic safe, Fire resistant

INSTALLATION OF - 12P, Copper wire,stranded,0.75 mm²,armoured, Non Intrinsic Safe , Flame Retardant

INSTALLATION OF - 1T, Copper wire,stranded, 1.5 mm²,armoured, Non Intrinsic safe, Fire Resistant

INSTALLATION OF - 12T, Copper wire,stranded,1.5 mm²,armoured, Non Intrinsic safe, Fire Resistant

INSTALLATION OF - 6T, Copper wire,stranded,1.5 mm²,armoured, Intrinsic safe, Flame Retardant

INSTALLATION OF - 6T, Copper wire,stranded,1.5 mm²,armoured, Non Intrinsic safe, Fire Resistant

INSTALLATION OF - 8T, Copper wire,stranded, 1.5 mm²,armoured, Non Intrinsic safe, Flame Retardant

INSTALLATION OF - 12P, Copper wire,stranded,0.75 mm²,armoured, Non Intrinsic safe, Fire Resistant

INSTALLATION OF - Power cable -3C X 2.5mm2,armoured, Non Intrinsic safe, Flame Retardant

INSTALLATION OF - Power cable, 3CX 2.5 mm²,armoured, Non Intrinsic safe, Fire resistant

INSTALLATION OF - Power cable, 3CX 6 mm²,armoured, Non Intrinsic safe, Fire resistant

Scope of work includes Supply of Cables Glands with PVC hood, lugs, ferrules, cable ties,SS Cable tags & any other consumable required for Glanding & Termination of cables as per details mentioned

SUPPLY OF - Ex`d' certified to Zone2, IIC, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1/2"NPT(M), with Check Nut & PVC shroud

SUPPLY OF - Ex`d',certified to Zone2, IIC, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 3/4"NPT(M), with Check Nut & PVC shroud

SUPPLY OF - Ex`d', certified to Zone2, IIC,Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1 "NPT(M), with Check Nut & PVC shroud

SUPPLY OF - Ex`d', certified to Zone2, IIC,Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1 1/4"NPT(M), with Check Nut & PVC shroud

SUPPLY OF - Ex`d', certified to Zone2, IIC,Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 3/4"ET(M), with Check Nut & PVC shroud

SUPPLY OF - Ex`d',certified to Zone2, IIC, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1 1/2"NPT(M), with Check Nut & PVC shroud

SUPPLY OF - Ex`d', certified to Zone2, IIC,Double Compression ET nickel plated brass Cable Gland of 1 1/2" size, with Check Nut & PVC shroud

SUPPLY OF - Ex`d',certified to Zone2, IIC, Double Compression ET nickel plated brass Cable Gland of 1 1/4" size, with Check Nut & PVC shroud

SUPPLY OF - Ex`d', certified to Zone2, IIC,Double Compression ET nickel plated brass Cable Gland of 2 " size, with Check Nut & PVC shroud

SUPPLY OF - Ex`d',certified to Zone2, IIC, Nickel Plated Brass adapter for cable entry M20 to 1/2" NPT

SUPPLY OF - Ex`d',certified to Zone2, IIC, Nickel Plated Brass adapter for cable entry M25 to 1" NPT

SUPPLY OF - Ex`d', certified to Zone2, IIC,Nickel Plated Brass reducer for cable entry 1" NPT to 1/2" NPT

SUPPLY OF - Ex`d', certified to Zone2, IIC,Nickel Plated Brass reducer for cable entry 1-1/4 NPT to 1" NPT

SUPPLY OF - Ex`d',certified to Zone2, IIC, Nickel Plated Brass reducer for cable entry 1-1/2 NPT to 1-1/4" NPT

SUPPLY OF - Ex`d', certified to Zone2, IIC,Nickel Plated Brass adapter for cable entry M20 to 3/4" ET

SUPPLY OF - Ex`d',certified to Zone2, IIC, Nicker plated Brass Stopper Plug, 1/2" NPT

SUPPLY OF - Weatherproof to IP 66, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1/2"NPT(M), with Check Nut & PVC shroud

SUPPLY OF - Weatherproof to IP 66,Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1 "NPT(M), with Check Nut & PVC shroud

SUPPLY OF - Weatherproof to IP 66, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1 1/2"NPT(M), with Check Nut & PVC shroud

SUPPLY OF - Weatherproof to IP 66, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 2"NPT(M), with Check Nut & PVC shroud

Scope of work includes Connection/Termination of Cables Glands with PVC hood, lugs, ferrules, cable ties,SS Cable tags & any other consumable required for Glanding & Termination of cables Taking delivery (including related handling) at on Site Contractor warehouse, on-site transportation, handling, and temporary storage. Cables preparation, and arrangement inside panels and junction boxes, Instruments, Analyzers etc . Glanding of Cable to Panels/Cabinets/ Junction box/ Instrument etc.in field and/or control rooms, switchgear room, Rack rooms, Analyzer shelters Terminals execution and connections (Terminations) & Cable and conductor identification and marking/ Ferruling. Shields and armours grounding as per specification. Cables preparation, and arrangement inside panels and junction boxes Supply and installation of Cable sleeves, Copper / Steel/ Aluminium lugs/ Ferrules including printing etc Before glanding/termination meggering & continuity test shall be performed for cables. Removal & refitting of MCT Blocks . Pre-insulated tinned copper compression type lugs shall be used for cable termination in general as per project specification Cable tie to be provided for cable dressing . proper dressing to be carried out inside panel and Junction boxes, shelters etc Inspection and test This scope of work include termination at Instrument side, Local panel, Analyzer side, Junction box side, Control room side.

INSTALLATION OF - Ex`d' certified to Zone2, IIC, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1/2"NPT(M), with Check Nut & PVC shroud

INSTALLATION OF - Ex`d',certified to Zone2, IIC, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 3/4"NPT(M), with Check Nut & PVC shroud

INSTALLATION OF - Ex`d', certified to Zone2, IIC,Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1 "NPT(M), with Check Nut & PVC shroud

INSTALLATION OF - Ex`d', certified to Zone2, IIC,Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1 1/4"NPT(M), with Check Nut & PVC shroud

INSTALLATION OF - Ex`d', certified to Zone2, IIC,Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 3/4"ET(M), with Check Nut & PVC shroud

INSTALLATION OF - Ex`d',certified to Zone2, IIC, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1 1/2"NPT(M), with Check Nut & PVC shroud

INSTALLATION OF - Ex`d', certified to Zone2, IIC,Double Compression ET nickel plated brass Cable Gland of 1 1/2" size, with Check Nut & PVC shroud

INSTALLATION OF - Ex`d',certified to Zone2, IIC, Double Compression ET nickel plated brass Cable Gland of 1 1/4" size, with Check Nut & PVC shroud

INSTALLATION OF - Ex`d', certified to Zone2, IIC,Double Compression ET nickel plated brass Cable Gland of 2 " size, with Check Nut & PVC shroud

INSTALLATION OF - Ex`d',certified to Zone2, IIC, Nickel Plated Brass adapter for cable entry M20 to 1/2" NPT

INSTALLATION OF - Ex`d',certified to Zone2, IIC, Nickel Plated Brass adapter for cable entry M25 to 1" NPT

INSTALLATION OF - Ex`d', certified to Zone2, IIC,Nickel Plated Brass reducer for cable entry 1" NPT to 1/2" NPT

INSTALLATION OF - Ex`d', certified to Zone2, IIC,Nickel Plated Brass reducer for cable entry 1-1/4 NPT to 1" NPT

INSTALLATION OF - Ex`d',certified to Zone2, IIC, Nickel Plated Brass reducer for cable entry 1-1/2 NPT to 1-1/4" NPT

INSTALLATION OF - Ex`d', certified to Zone2, IIC,Nickel Plated Brass adapter for cable entry M20 to 3/4" ET

INSTALLATION OF - Ex`d',certified to Zone2, IIC, Nicker plated Brass Stopper Plug, 1/2" NPT

INSTALLATION OF - Weatherproof to IP 66, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1/2"NPT(M), with Check Nut & PVC shroud

INSTALLATION OF - Weatherproof to IP 66,Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1 "NPT(M), with Check Nut & PVC shroud

INSTALLATION OF - Weatherproof to IP 66, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 1 1/2"NPT(M), with Check Nut & PVC shroud

INSTALLATION OF - Weatherproof to IP 66, Cable Gland, Mettalic / Nickel plated Brass Double Compression Ferrule Type, 2"NPT(M), with Check Nut & PVC shroud

SUPPLY OF IMPULSE TUBING & PNEUMATIC TUBING AND ACCESSORIES

SUPPLY OF - 1/2"NPT(M) X 1/2" OD Male Connector Compression Type, SS 316

SUPPLY OF - 1/4"NPT(M) X 1/2" OD Male Connector Compression Type, SS 316

SUPPLY OF - 1/4"NPT(M) X 1/4" OD Male Connector Compression Type, SS 316

SUPPLY OF - 1/2" OD Ferrules,SS316

SUPPLY OF - 1/4" OD Ferrules,SS316

SUPPLY OF - 1/2" OD Union Compression Type, SS 316

SUPPLY OF - 1/2" OD Tubing, SS 316

SUPPLY OF - 1/4" OD Tubing, SS 316

SUPPLY OF - 3" Pot with 3/4" Flanged Connections & Blinded at one end-IBR, Condesate pot, CS

SUPPLY OF - 1/2'" OD SS 316 Needle Valves

SUPPLY OF - 1/2" NPTF SS316 Ball Valves

SUPPLY OF - 1/2" Tube OD TEE,SS316

SUPPLY OF - 1/2" OD Tube plug connecter,SS316

SUPPLY OF - 1/4" BSP(M) X 1/2" OD Male Connector Compression Type, SS 316

SUPPLY OF - 8mm Tube (MOC: PU or PE)

SUPPLY OF - 12mm Tube (MOC: PU or PE)

SUPPLY OF - 90° elbow (Push type)- 8mm OD x 8mmOD (MOC: PP)

SUPPLY OF - Equal Tee (Push type) -8mm OD (MOC: PP)

SUPPLY OF - 90° elbow (Push type)-12mmOD x 12mmOD (MOC: PP)

SUPPLY OF - Equal Tee (Push type)-12mm OD (MOC: PP)

SUPPLY OF - Y type Tee (Push type)-12mm OD (MOC: PP)

SUPPLY OF - Y type Tee (Push type)-8mm OD (MOC: PP)

SUPPLY OF - Connector (Push type)-1/4" NPT x 8mm OD (MOC: PP)

SUPPLY OF - Connector (Push type)-1/2" NPT x 12mm OD (MOC: PP)

SUPPLY OF - 90° elbow (Push type)-1/2" NPT x 12mm OD (MOC: PP)

SUPPLY OF - 90° elbow (Push type)-1/2" NPT x 8mm OD (MOC: PP)

SUPPLY OF - Flow Control Valve (Push type)-1/2" NPT x 8mm OD (MOC: PP)

SUPPLY OF - Flow Control Valve (Push type)-1/4" NPT x 8mm OD (MOC: PP)

SUPPLY OF - union (Push type)-12mm OD x 8mm OD (MOC: PP)

SUPPLY OF - union (Push type)-12mm OD x 12mm OD (MOC: PP)

SUPPLY OF - union (Push type)-8mm OD x 8mm OD (MOC: PP)

SUPPLY OF - Flow Control Valve (Push type)-1/2" NPT x 12 mm OD (MOC: PP)

SUPPLY OF - Connector (Push type)-1/2" NPT x 8mm OD (MOC: PP)

SUPPLY OF - Connector (Push type)-1/4" NPT x 12mm OD (MOC: PP)

SUPPLY OF - Connector (Push type)-1/8" NPT x 8mm OD (MOC: PP)

SUPPLY OF - 2" Sch 80, Air Distributors and Accessories (10 Taps), SS 316

SUPPLY OF - 1/2"(F)X1/2"(F) NPT, Manifold 2 Valve-For Pressure gauge,SS316

SUPPLY OF - 4 way cross - 1/2"NPT (F) x 1/2"NPT (F) x 1/2"NPT (F) x 1/2"NPT (F),SS316

SUPPLY OF - 1/2" NPT(F) Brass Hex Nipple

SUPPLY OF - 3/8" OD Neddle Valve,SS316

SUPPLY OF - Female Branch Tee - 1/4 NPT (M) X 1/4 NPT(F) X 1/4"NPT(F) ,SS316

SUPPLY OF - 1" NPT(F) X1" OD Female connecter Compression Type,SS316

SUPPLY OF - 1/4" NPT(F) X1/4" OD Female connecter Compression Type,SS316

SUPPLY OF - 1/2" NPT(F) X1/2" OD Female connecter Compression Type,SS316

SUPPLY OF - 1/4" NTP(F) X1/4" NPT(F) Female Elbow,SS316

SUPPLY OF - 1/4" NTP(M) X1/4" NPT(F) Elbow,SS316

SUPPLY OF - 1/2" OD Check Valves,SS316

SUPPLY OF - 1/4" NPT , 4" Long Hex Long Nipple,SS316

SUPPLY OF - 1/4" NPT (M) X 1/2" NPT(M) Reducing Adapter,SS316

SUPPLY OF - 1/4" NPT X 3" long Hex long Nipple,SS316

SUPPLY OF - 1/2" NPT (M) X 1/2" NPT(M) Adapter ,SS316

SUPPLY OF - 1/4" NPT(M) X 1/8" NPT(M),Reducing adapter SS316

SUPPLY OF - 1/2" NPT(M) Hex Plug,SS316

SUPPLY OF - 1" NPT(M) X1" OD Male connecter Compression Type,SS316

SUPPLY OF - 1" NPT(M) X1/2" OD Male connecter Compression Type,SS316

SUPPLY OF - 3/4" NPT(M) X1/2" OD Male connecter Compression Type,SS316

SUPPLY OF - 1/2" NPT(M) X 3/8" OD Male connecter Compression Type,SS316

SUPPLY OF - 1/4" NPT(M) X 3/8" OD Male connecter Compression Type,SS316

SUPPLY OF - 3/8" NPT(M) X 3/8" OD Male connecter Compression Type,SS316

SUPPLY OF - 1/4" NPT(M) X5/16" OD Male connecter Compression Type,SS316

SUPPLY OF - 1" NPT(M) X1" OD Male Elbow,SS316

SUPPLY OF - 1/4" NPT(M) X1/2" OD Male Elbow,SS316

SUPPLY OF - 1/4" NTP(M) X1/4" NPT(M) Elbow,SS316

SUPPLY OF - MALE ELBOW-3/4 OD x 1/2 NPT (M),SS316

SUPPLY OF - MALE ELBOW-3/8 OD x 1/4 NPT(M),SS316

SUPPLY OF - MALE ELBOW-3/8 OD x 3/8 NPT(M),SS316

SUPPLY OF - REDUCING ADAPTOR -1" NPT (M) x 1/2 NPT (F),SS316

SUPPLY OF - REDUCING ADAPTOR -1" NPT (M) x 3/8 NPT (F),SS316

SUPPLY OF - REDUCING ADAPTOR -1/2 NPT(M) x 1/4 NPT (F),SS316

SUPPLY OF - ADAPTOR -1/2 NPT(M) x 1/2 NPT (M),SS316

SUPPLY OF - REDUCING ADAPTOR -1/2 NPT(M) x 1/4 NPT(M),SS316

SUPPLY OF - REDUCING ADAPTOR -1/4 NPT (M) x 1/2 NPT (F),SS316

SUPPLY OF - ADAPTOR -1/4 NPT (M) x 1/4 NPT (F),SS316

SUPPLY OF - ADAPTOR -1/4 NPT (M) x 1/4 NPT (M),SS316

SUPPLY OF - ADAPTOR -3/8 NPT(M) x 3/8 NPT (M),SS316

SUPPLY OF - ADAPTOR NIPPLE-1/2 NPT(M) x1/2 NPT(M),SS316

SUPPLY OF - REDUCING ADAPTOR NIPPLE-1/2 NPTM x1/4 NPT(F),SS316

SUPPLY OF - REDUCING ADAPTOR NIPPLE-3/8 NPTM x 1/4 NPT(F),SS316

SUPPLY OF - REDUCING ADAPTOR NIPPLE-1/4 NPT(M) x 1/2 NPT(M),SS316

SUPPLY OF - REDUCING BUSHING-1/4 NPT (M) x 1/2 NPT (F),SS316

SUPPLY OF - REDUCING BUSHING-1" NPT (M) x 1/2 NPT (F),SS316

SUPPLY OF - BUSHING-1/2 NPT (F) x 1/2 NPT (M),SS316

SUPPLY OF - REDUCING BUSHING-1/4 NPT (F)x 1/2 NPT (M),SS316

SUPPLY OF - BUSHING-1/4 NPT (M) x 1/4 NPT (F),SS316

SUPPLY OF - REDUCING BUSHING-2" NPT (M) x1" NPT (F),SS316

SUPPLY OF - REDUCING BUSHING-3/4 NPT(M) x 3/8 NPT (F),SS316

SUPPLY OF - REDUCING HEX-1" NPT (M) x 1/2 NPT (M),SS316

SUPPLY OF - REDUCING NIPPLE-1/8 NPT (M) x 1/4 NPT(M),SS316

SUPPLY OF - ROUND SS NIPPLE PIPE-1/4 NPT (M) x 1/4 NPT (M) LENGTH 1",SS316

SUPPLY OF - ROUND SS NIPPLE PIPE-1/4 NPT (M) x 1/4 NPT (M) LENGTH 3",SS316

SUPPLY OF - ROUND SS NIPPLE PIPE-1/2 NPT (M) x 1/2 NPT (M) LENGTH 1",SS316

SUPPLY OF - ROUND SS NIPPLE PIPE-1/2 NPT (M) x 1/2 NPT (M),SS316LENGTH 3"

SUPPLY OF - ROUND SS NIPPLE PIPE-1/2 NPT (M) x 1/2 NPT (M) LENGTH 2",SS316

SUPPLY OF - RV-PRESS RELIFE -VALVE 1/4"OD,SS316

SUPPLY OF - STR-STRAINER (Y TYPE)1/4"NPT(F),SS316

SUPPLY OF - 1/2" OD Ferrules, Brass

SUPPLY OF - 1/4" OD Ferrules, Brass

SUPPLY OF - 3/8" OD Ferrules, SS 316

SUPPLY OF - MALE CONNECTOR 3/4"NPTM X 1/2"OD,SS316

SUPPLY OF - Reducing Concentric Nipple 3/4'' NPT X 1/2'' OD,SS316

SUPPLY OF - PLUG 3/4"NPTM,SS316

SUPPLY OF - 1/2"OD UNION CROSS Compression Type,SS316

SUPPLY OF - 1/2"NPTx 1/2"ODx1/2"OD MALE RUN TEE Compression Type,SS316

SUPPLY OF - 1/2" NPT M Blind plugs for instruments,SS316

SUPPLY OF - 1/2" NPT F Blind plugs for instruments,SS316

SUPPLY OF - 3/4" NPT Male Plugs,SS316

SUPPLY OF - MALE ELBOW-1/4 OD x 1/4 NPT (M),SS316

SUPPLY OF - MALE ELBOW-1/4 OD x 1/8 NPT (M),SS316

SUPPLY OF - 1/2" NPT(M)X1/4"OD Male connector compression type,SS316

SUPPLY OF - MALE ELBOW-1/4"ODX1/2"NPT(M),SS316

SUPPLY OF - ¼” OD X ¼” NPT(M) Bulk head connecter,SS316

INSTALLATION OF IMPULSE TUBING & PNEUMATIC TUBING: Scope of work includes installation of Tubes & Tube fittings, laying of tubes on trays includes following works; Taking delivery (including related handling) at on Site Contractor warehouse, on-site transportation, handling, and temporary storage. Contractor shall study optimal routing from the impulse line (manifold) up to the instrument & Valve air inlet upto Air manifold as per process hook up drawing provided by the site in-charge. Fabrication of manifold on the basis of process hook up drawings for Impulse line . Laying, supporting, clamping, cutting, threading, bending & other similar works involved in fabrication of the impulse sample lines / SS tubes & fast loop for analyser Fixing of isolation valves & tube fittings etc as per process hook up provided by the site in-charge, as per Process hook-up . Replacement of Existing Tubes wherever required. Replacement of Existing Tube fittings wherever required. SS tube connection to the process / impulse pipe/ tube &, to the instruments. Cleaning / blowing & pressure test of the tubing. Fixing of fittings, isolation valves & tube fittings, Air Manifolds etc. Supports to be provided for Air Manifolds Manifold installation, supporting and clamping at one meter interval. Manifold connection to the process lines & to the instruments. Cleaning / blowing & hydraulic test of the impulse lines (manifold) Scope includes supply of paints, clamps, supports, consumables and other material required. Test on impulse tubes & Pneumatic tubes shall be applicable as per project requirement. If required during laying of impulse lines, making temporary supports / scaffolding etc. is in Contractors scope of work. Any other work not specified above but required for laying of impulse pipe (manifold) is also in Contractor's scope of work.

INSTALLATION OF - 1/2"NPT(M) X 1/2" OD Male Connector Compression Type, SS 316

INSTALLATION OF - 1/4"NPT(M) X 1/2" OD Male Connector Compression Type, SS 316

INSTALLATION OF - 1/4"NPT(M) X 1/4" OD Male Connector Compression Type, SS 316

INSTALLATION OF - 1/2" OD Ferrules,SS316

INSTALLATION OF - 1/4" OD Ferrules,SS316

INSTALLATION OF - 1/2" OD Union Compression Type, SS 316

INSTALLATION OF - 1/2" OD Tubing, SS 316

INSTALLATION OF - 1/4" OD Tubing, SS 316

INSTALLATION OF - 3" Pot with 3/4" Flanged Connections & Blinded at one end-IBR, Condesate pot, CS

INSTALLATION OF - 1/2'" OD SS 316 Needle Valves

INSTALLATION OF - 1/2" NPTF SS316 Ball Valves

INSTALLATION OF - 1/2" Tube OD TEE,SS316

INSTALLATION OF - 1/2" OD Tube plug connecter,SS316

INSTALLATION OF - 1/4" BSP(M) X 1/2" OD Male Connector Compression Type, SS 316

INSTALLATION OF - 8mm Tube (MOC: PU or PE)

INSTALLATION OF - 12mm Tube (MOC: PU or PE)

INSTALLATION OF - 90° elbow (Push type)- 8mm OD x 8mmOD (MOC: PP)

INSTALLATION OF - Equal Tee (Push type) -8mm OD (MOC: PP)

INSTALLATION OF - 90° elbow (Push type)-12mmOD x 12mmOD (MOC: PP)

INSTALLATION OF - Equal Tee (Push type)-12mm OD (MOC: PP)

INSTALLATION OF - Y type Tee (Push type)-12mm OD (MOC: PP)

INSTALLATION OF - Y type Tee (Push type)-8mm OD (MOC: PP)

INSTALLATION OF - Connector (Push type)-1/4" NPT x 8mm OD (MOC: PP)

INSTALLATION OF - Connector (Push type)-1/2" NPT x 12mm OD (MOC: PP)

INSTALLATION OF - 90° elbow (Push type)-1/2" NPT x 12mm OD (MOC: PP)

INSTALLATION OF - 90° elbow (Push type)-1/2" NPT x 8mm OD (MOC: PP)

INSTALLATION OF - Flow Control Valve (Push type)-1/2" NPT x 8mm OD (MOC: PP)

INSTALLATION OF - Flow Control Valve (Push type)-1/4" NPT x 8mm OD (MOC: PP)

INSTALLATION OF - union (Push type)-12mm OD x 8mm OD (MOC: PP)

INSTALLATION OF - union (Push type)-12mm OD x 12mm OD (MOC: PP)

INSTALLATION OF - union (Push type)-8mm OD x 8mm OD (MOC: PP)

INSTALLATION OF - Flow Control Valve (Push type)-1/2" NPT x 12 mm OD (MOC: PP)

INSTALLATION OF - Connector (Push type)-1/2" NPT x 8mm OD (MOC: PP)

INSTALLATION OF - Connector (Push type)-1/4" NPT x 12mm OD (MOC: PP)

INSTALLATION OF - Connector (Push type)-1/8" NPT x 8mm OD (MOC: PP)

INSTALLATION OF - 2" Sch 80, Air Distributors and Accessories (10 Taps), SS 316

INSTALLATION OF - 1/2"(F)X1/2"(F) NPT, Manifold 2 Valve-For Pressure gauge,SS316

INSTALLATION OF - 4 way cross - 1/2"NPT (F) x 1/2"NPT (F) x 1/2"NPT (F) x 1/2"NPT (F),SS316

INSTALLATION OF - 1/2" NPT(F) Brass Hex Nipple

INSTALLATION OF - 3/8" OD Neddle Valve,SS316

INSTALLATION OF - Female Branch Tee - 1/4 NPT (M) X 1/4 NPT(F) X 1/4"NPT(F) ,SS316

INSTALLATION OF - 1" NPT(F) X1" OD Female connecter Compression Type,SS316

INSTALLATION OF - 1/4" NPT(F) X1/4" OD Female connecter Compression Type,SS316

INSTALLATION OF - 1/2" NPT(F) X1/2" OD Female connecter Compression Type,SS316

INSTALLATION OF - 1/4" NTP(F) X1/4" NPT(F) Female Elbow,SS316

INSTALLATION OF - 1/4" NTP(M) X1/4" NPT(F) Elbow,SS316

INSTALLATION OF - 1/2" OD Check Valves,SS316

INSTALLATION OF - 1/4" NPT , 4" Long Hex Long Nipple,SS316

INSTALLATION OF - 1/4" NPT (M) X 1/2" NPT(M) Reducing Adapter,SS316

INSTALLATION OF - 1/4" NPT X 3" long Hex long Nipple,SS316

INSTALLATION OF - 1/2" NPT (M) X 1/2" NPT(M) Adapter ,SS316

INSTALLATION OF - 1/4" NPT(M) X 1/8" NPT(M),Reducing adapter SS316

INSTALLATION OF - 1/2" NPT(M) Hex Plug,SS316

INSTALLATION OF - 1" NPT(M) X1" OD Male connecter Compression Type,SS316

INSTALLATION OF - 1" NPT(M) X1/2" OD Male connecter Compression Type,SS316

INSTALLATION OF - 3/4" NPT(M) X1/2" OD Male connecter Compression Type,SS316

INSTALLATION OF - 1/2" NPT(M) X 3/8" OD Male connecter Compression Type,SS316

INSTALLATION OF - 1/4" NPT(M) X 3/8" OD Male connecter Compression Type,SS316

INSTALLATION OF - 3/8" NPT(M) X 3/8" OD Male connecter Compression Type,SS316

INSTALLATION OF - 1/4" NPT(M) X5/16" OD Male connecter Compression Type,SS316

INSTALLATION OF - 1" NPT(M) X1" OD Male Elbow,SS316

INSTALLATION OF - 1/4" NPT(M) X1/2" OD Male Elbow,SS316

INSTALLATION OF - 1/4" NTP(M) X1/4" NPT(M) Elbow,SS316

INSTALLATION OF - MALE ELBOW-3/4 OD x 1/2 NPT (M),SS316

INSTALLATION OF - MALE ELBOW-3/8 OD x 1/4 NPT(M),SS316

INSTALLATION OF - MALE ELBOW-3/8 OD x 3/8 NPT(M),SS316

INSTALLATION OF - REDUCING ADAPTOR -1" NPT (M) x 1/2 NPT (F),SS316

INSTALLATION OF - REDUCING ADAPTOR -1" NPT (M) x 3/8 NPT (F),SS316

INSTALLATION OF - REDUCING ADAPTOR -1/2 NPT(M) x 1/4 NPT (F),SS316

INSTALLATION OF - ADAPTOR -1/2 NPT(M) x 1/2 NPT (M),SS316

INSTALLATION OF - REDUCING ADAPTOR -1/2 NPT(M) x 1/4 NPT(M),SS316

INSTALLATION OF - REDUCING ADAPTOR -1/4 NPT (M) x 1/2 NPT (F),SS316

INSTALLATION OF - ADAPTOR -1/4 NPT (M) x 1/4 NPT (F),SS316

INSTALLATION OF - ADAPTOR -1/4 NPT (M) x 1/4 NPT (M),SS316

INSTALLATION OF - ADAPTOR -3/8 NPT(M) x 3/8 NPT (M),SS316

INSTALLATION OF - ADAPTOR NIPPLE-1/2 NPT(M) x1/2 NPT(M),SS316

INSTALLATION OF - REDUCING ADAPTOR NIPPLE-1/2 NPTM x1/4 NPT(F),SS316

INSTALLATION OF - REDUCING ADAPTOR NIPPLE-3/8 NPTM x 1/4 NPT(F),SS316

INSTALLATION OF - REDUCING ADAPTOR NIPPLE-1/4 NPT(M) x 1/2 NPT(M),SS316

INSTALLATION OF - REDUCING BUSHING-1/4 NPT (M) x 1/2 NPT (F),SS316

INSTALLATION OF - REDUCING BUSHING-1" NPT (M) x 1/2 NPT (F),SS316

INSTALLATION OF - BUSHING-1/2 NPT (F) x 1/2 NPT (M),SS316

INSTALLATION OF - REDUCING BUSHING-1/4 NPT (F)x 1/2 NPT (M),SS316

INSTALLATION OF - BUSHING-1/4 NPT (M) x 1/4 NPT (F),SS316

INSTALLATION OF - REDUCING BUSHING-2" NPT (M) x1" NPT (F),SS316

INSTALLATION OF - REDUCING BUSHING-3/4 NPT(M) x 3/8 NPT (F),SS316

INSTALLATION OF - REDUCING HEX-1" NPT (M) x 1/2 NPT (M),SS316

INSTALLATION OF - REDUCING NIPPLE-1/8 NPT (M) x 1/4 NPT(M),SS316

INSTALLATION OF - ROUND SS NIPPLE PIPE-1/4 NPT (M) x 1/4 NPT (M) LENGTH 1",SS316

INSTALLATION OF - ROUND SS NIPPLE PIPE-1/4 NPT (M) x 1/4 NPT (M) LENGTH 3",SS316

INSTALLATION OF - ROUND SS NIPPLE PIPE-1/2 NPT (M) x 1/2 NPT (M) LENGTH 1",SS316

INSTALLATION OF - ROUND SS NIPPLE PIPE-1/2 NPT (M) x 1/2 NPT (M),SS316LENGTH 3"

INSTALLATION OF - ROUND SS NIPPLE PIPE-1/2 NPT (M) x 1/2 NPT (M) LENGTH 2",SS316

INSTALLATION OF - RV-PRESS RELIFE -VALVE 1/4"OD,SS316

INSTALLATION OF - STR-STRAINER (Y TYPE)1/4"NPT(F),SS316

INSTALLATION OF - 1/2" OD Ferrules, Brass

INSTALLATION OF - 1/4" OD Ferrules, Brass

INSTALLATION OF - 3/8" OD Ferrules, SS 316

INSTALLATION OF - MALE CONNECTOR 3/4"NPTM X 1/2"OD,SS316

INSTALLATION OF - Reducing Concentric Nipple 3/4'' NPT X 1/2'' OD,SS316

INSTALLATION OF - PLUG 3/4"NPTM,SS316

INSTALLATION OF - 1/2"OD UNION CROSS Compression Type,SS316

INSTALLATION OF - 1/2"NPTx 1/2"ODx1/2"OD MALE RUN TEE Compression Type,SS316

INSTALLATION OF - 1/2" NPT M Blind plugs for instruments,SS316

INSTALLATION OF - 1/2" NPT F Blind plugs for instruments,SS316

INSTALLATION OF - 3/4" NPT Male Plugs,SS316

INSTALLATION OF - MALE ELBOW-1/4 OD x 1/4 NPT (M),SS316

INSTALLATION OF - MALE ELBOW-1/4 OD x 1/8 NPT (M),SS316

INSTALLATION OF - 1/2" NPT(M)X1/4"OD Male connector compression type,SS316

INSTALLATION OF - MALE ELBOW-1/4"ODX1/2"NPT(M),SS316

INSTALLATION OF - ¼” OD X ¼” NPT(M) Bulk head connecter,SS316

SUPPLY OF JUNCTION BOXES:

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size,36 Terminals, 12P, Exd , IIC ,T3 Branch Cable entry : 12 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1.25" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size,18 Terminals, 6P, Exd , IIC ,T3 Branch Cable entry : 6 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size,48 Terminals, 12T, Exd , IIC ,T3 Branch Cable entry : 12 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1.5" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size,32 Terminals, 8T, Exd , IIC ,T3 Branch Cable entry : 8 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1.25" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size,24 Terminals, 6T, Exd , IIC ,T3 Branch Cable entry : 6 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1.25" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size,72 Terminals, 24P, Exd , IIC ,T3 Branch Cable entry : 24 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1.5" NPT

INSTALLATION OF JUNCTION BOXES: Scope of work includes installation of Junction Boxes Taking delivery (including related handling) at on SIte Contractor warehouse, on-site transportation, handling, and temporary storage Masonary Works as required including Nuts/ Bolts, Anchor Fastners etc Junction boxes (Exd & Exe) installation Junction boxes grounding & Cable gland and/or sealing installation on junction boxes Adequate protection for junction boxes, during installation and connection activities Installation of Canopies/ Sun shades (Canopies to quoted seperately) Painting as per Project Specification Stenciling, Tag numbering on Junction Boxes to be done Adequate protection for JB, during installation and connection activities including supply of protection material like polyethylene

INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size,36 Terminals, 12P, Exd , IIC ,T3 Branch Cable entry : 12 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1.25" NPT

INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size,18 Terminals, 6P, Exd , IIC ,T3 Branch Cable entry : 6 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1" NPT

INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size,48 Terminals, 12T, Exd , IIC ,T3 Branch Cable entry : 12 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1.5" NPT

INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size,32 Terminals, 8T, Exd , IIC ,T3 Branch Cable entry : 8 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1.25" NPT

INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size,24 Terminals, 6T, Exd , IIC ,T3 Branch Cable entry : 6 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1.25" NPT

INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size,72 Terminals, 24P, Exd , IIC ,T3 Branch Cable entry : 24 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1.5" NPT

SUPPLY OF JUNCTION BOXES:

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size, 60 nos. of TB. Weather proof to IP 66 Branch Cable entry : 24 nos of 1/2" NPT(F) Multi cable entry: 1 no of 2" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size, 60 nos. of TB. Weather proof to IP 66 Branch Cable entry : 24 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1 1/2" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size, 15 nos. of TB. Weather proof to IP 66. Branch Cable entry : 6 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size, 30 nos. of TB. Weather proof to IP 66. Branch Cable entry : 12 nos of 1/2" NPT(F) Multi cable entry: 2 nos of 1" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size, 40 nos. of TB . Weather proof to IP 66. Branch Cable entry : 12 nos of 1/2" NPT(F) Multi cable entry: 1 nos of 1 1/2" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size, 60 nos. of TB . Weather proof to IP 66. Branch Cable entry : 24 nos of 1/2" NPT(F) Multi cable entry: 2 nos of 1 1/2" NPT

SUPPLY OF - Diecast Junction Box with 2.5 sqmm terminal size, 60 nos. of TB . Weather proof to IP 66. Branch Cable entry : 24 nos of 1/2" NPT(F) Multi cable entry: 1 nos of 1" NPT Multi cable entry: 1 nos of 1 1/2" NPT

REMOVAL OF EXISTING JUNCTION BOXES& INSTALLATION OF JUNCTION BOXES & CANNOPIES Scope of work includes removal of existing Juction boxes, installation of new Junction Boxes & Canopies for junction boxes Taking delivery (including related handling) at on Site Contractor warehouse, on-site transportation, handling, and temporary storage Masonary Works as required including Nuts/ Bolts, Anchor Fastners etc Junction boxes (Exd & Exe) replacement in place of existing includes disconnection of existing cable glands & existing terminations, marking of existing cables & modification of supports. Installation of new junction boxes, glanding & termination of existing cables. Junction boxes grounding & Cable gland and/or sealing installation on junction boxes Installation of Canopies/ Sun shades (Canopies to quoted seperately) Adequate protection for junction boxes, during installation and connection activities Painting of supports. Stenciling, Tag numbering on Junction Boxes to be done Adequate protection for JB, during installation and connection activities including supply of protection material like polyethylene

REMOVAL AND INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size, 60 nos. of TB. Weather proof to IP 66 Branch Cable entry : 24 nos of 1/2" NPT(F) Multi cable entry: 1 no of 2" NPT

REMOVAL AND INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size, 60 nos. of TB. Weather proof to IP 66 Branch Cable entry : 24 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1 1/2" NPT

REMOVAL AND INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size, 15 nos. of TB. Weather proof to IP 66. Branch Cable entry : 6 nos of 1/2" NPT(F) Multi cable entry: 1 no of 1" NPT

REMOVAL AND INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size, 30 nos. of TB. Weather proof to IP 66. Branch Cable entry : 12 nos of 1/2" NPT(F) Multi cable entry: 2 nos of 1" NPT

REMOVAL AND INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size, 40 nos. of TB . Weather proof to IP 66. Branch Cable entry : 12 nos of 1/2" NPT(F) Multi cable entry: 1 nos of 1 1/2" NPT

REMOVAL AND INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size, 60 nos. of TB . Weather proof to IP 66. Branch Cable entry : 24 nos of 1/2" NPT(F) Multi cable entry: 2 nos of 1 1/2" NPT

REMOVAL AND INSTALLATION OF - Diecast Junction Box with 2.5 sqmm terminal size, 60 nos. of TB . Weather proof to IP 66. Branch Cable entry : 24 nos of 1/2" NPT(F) Multi cable entry: 1 nos of 1" NPT Multi cable entry: 1 nos of 1 1/2" NPT

SUPPLY OF CABLE TRAYS

SUPPLY OF - 50W Perforated GI Cable Tray

SUPPLY OF - 100W Perforated GI Cable Tray

SUPPLY OF - 150W Perforated GI Cable Tray

SUPPLY OF - 300W Perforated GI Cable Tray

SUPPLY OF - 600W Ladder GI Cable Tray

SUPPLY OF - 150x50 FRP Cable tray

SUPPLY OF - 100x50 FRP Cable tray

SUPPLY OF - 50x25 FRP Cable tray

SUPPLY OF - 300x50 FRP Cable tray

SUPPLY OF - 300x100 FRP Cable tray

SUPPLY OF - 600x100 FRP Cable tray

SUPPLY OF - 50mm dia GI Conduit

SUPPLY OF - 12mm SS Flexible Conduit

SUPPLY OF - 20mm SS flexible conduit

SUPPLY OF - 1/2" GI Pipe

INSTALLATION OF CABLE TRAYS Scope of work includes installation of cable trays includes following activities: Taking delivery (including related handling) at on Site Contractor warehouse, on-site transportation, handling, and temporary storage. Contractor shall study tray routing where tray is to be installed. (if drawing is not available, then on the basis of cable schedule & control room equipment layout, contractor shall study the optimal route for cable tray and shall obtain with the site in-charge approval) Pre-fabricated supports if any, shall be fixed either to the floor and/or to the ceiling using expansion bolts inside control room or on column, beams, structural support in field by wielding / bolting. Contractor’s scope includes supply of the expansion bolts/ consumables including wielding rod, nut, bolts, washers etc. Cable tray shall be supported at every 1.5 / 2.0 meter or as specified in the drawings. For fixing the supports, civil work such as chipping work including supply of cement, concrete etc. is in contractor’s scope of supply. Cable trays shall be fixed to the supports by SS clamps / Holding clamps Cable tray sections shall also be fastened to each other with the coupler plates supplied along with cable trays. If required cable tray section shall be bend / cut by the contractor to suit the site conditions. If required contractor shall fabricate and install special pieces for bends, tees, crossings, risers etc. Grounding of Cable trays Before fixing the cable trays, supports shall be painted by the contractor. If required during erection of the cable trays making temporary supports / scaffolding etc. is in Contractors scope.

INSTALLATION OF - 50W Perforated GI Cable Tray

INSTALLATION OF - 100W Perforated GI Cable Tray

INSTALLATION OF - 150W Perforated GI Cable Tray

INSTALLATION OF - 300W Perforated GI Cable Tray

INSTALLATION OF - 600W Ladder GI Cable Tray

INSTALLATION OF - 750W Ladder GI Cable Tray

INSTALLATION OF - 150x50 FRP Cable tray

INSTALLATION OF - 100x50 FRP Cable tray

INSTALLATION OF - 50x25 FRP Cable tray

INSTALLATION OF - 300x50 FRP Cable tray

INSTALLATION OF - 300x100 FRP Cable tray

INSTALLATION OF - 600x100 FRP Cable tray

INSTALLATION OF - 50mm dia GI Conduit

INSTALLATION OF - 12mm SS Flexible Conduit

INSTALLATION OF - 20mm SS flexible conduit

INSTALLATION OF - 1/2" GI Pipe

SUPPLY OF MCT BLOCK

SUPPLY OF - MCT 8 X4

INSTALLATION OF MCT Scope of work includes Installation of MCT's. Taking delivery (including related handling) at on Site Contractor warehouse, on-site transportation, handling, and temporary storage. MCT frames of various sizes are be installed in the Control Room. MCT frame shall be fixed to the control room walls with anchor bolts (HILTI fasteners) all the civil work related to the installation of MCT on the wall is contractor’s scope. i). Contractor scope includes taking delivery from the ware house, on site transportation, storage, un packing etc. ii). Contractor shall install the MCT frames as per space available at ITR-1,ITR-2,ITR-3 , CCR , Boiler control room & DM Control Room iii)Contractor’s scope includes supply of cement, concrete, anchor bolts and other similar material required for installation of MCT frames. iv). If necessary chipping of the control room wall for the installation of the frame and making it good after installation of MCT is also in contractor’s scope. v). Any other work not specified above but necessary for installation of the frames is also in contractor’s scope.

INSTALLATION OF - MCT 8 X4

SUPPLY OF INSTRUMENT ITEMS SUPPORT STEEL & STANCHIONS

SUPPLY OF - Structural steel for tray support

SUPPLY OF - Stanchion with mounting accessories

INSTALLATION OF INSTRUMENT ITEMS SUPPORT STEEL & STANCHIONS Scope of work includes Fabrication, painting and installation of structural steel to support cable trays, Junction boxes, Tubes, Air Headers, Pushbuttons, Hooter, beacons & any other instrument works required to complete installation. installation of stanchions. The activity includes following works: Taking delivery (including related handling) at Contractor warehouse, on-site transportation, handling, and temporary storage. Mounting stands shall be suitable for installation on the plant permanent structure / RCC platform / grade etc. as the case may be. Mounting stands shall be as per project standards either welded or bolted to the permanent structures, for fixing supports on concrete structure HILTI Anchor's bolts shall be used. Minor civil work involved in the installation of the mounting stand shall be also done by the contactor including supply of cement, bricks, concrete,anchor bolts etc. Scope of work includes cutting, welding, threading, cleaning and other similar works involved in the fabrication of mounting stands. After the fabrication the same should be grit blasted and painted . Scope includes supply of welding electrodes, 2" IS:1239 Heavy Grade (as a min) Pipe, 6 mm Dia. Weep Hole at Low Point, U- Bolt Assembly shall be of Min. M12 size with Nuts and Spring Washers. All welds shall be 3 mm Fillet Weld Full Strength. Add 50 mm wherever Fire insulation is provided. Bolts shall be turned from M.S. Rounds confirming to IS: 432 Grade 1. Nuts and Washers shall be confirming to IS: 1363 and IS:3138. MS Plate (plate thickness 6 mm), anchor fasteners, cement, sand, bricks, concrete etc. and other similar material required for fabrication and installation of mounting stands. Grounding of Instruments. If required, making of temporary supports / scaffolding etc. is in Contractor’s scope Support to be fabricated as per installation standards

INSTALLATION OF - Structural steel for tray support

INSTALLATION OF - Stanchion with mounting accessories

SUPPLY OF INSTRUMENTS

SUPPLY OF - Push Button, Ex d Approved

SUPPLY OF - Gas Detectors -HC, IR Type , Ex d Approved

SUPPLY OF - Gas Detectors -H2 ,Diffusion Catalytic Type, Ex d Approved

SUPPLY OF - Hooter, Ex d Approved

SUPPLY OF - Beacons, Ex d Approved

SUPPLY OF - Linear Heat sensing cable along with retractable cable for all 5Nos of Tanks (Paraxylene Tanks) with JB & accessories

SUPPLY OF - Linear Heat sensing cable along with retractable cable for all 8Nos of ISBL Tanks with JB & accessories

SUPPLY OF - EOL JB's for LHS Cables

SUPPLY OF - Manual Call point with canopy (Break Glass, Conventional Ex-proof, Ex d, 24 VDC Power Supply, Die Cast Aluminium Housing Material, ATEX / IECEx & CCOE / PESO approvals, SS 316 Mounting Accessories), Ex d Approved

SUPPLY OF - AFR for Valves & other pneumatic devices with SS316 brackets & nuts bolts

INSTALLATION OF INSTRUMENTS: Scope of work includes Calibration,Installation, hook-up & Testing.Supply includes canopy Taking delivery (including related handling) at on Site Contractor warehouse, onsite transportation, handling, temporary storage. Calibration & Functional Test.Prepare Calibration & functional test reports OEM services along with all materials required for calibration of items like gas cyclinders, tubing,etc shall be included in scope of supply. Hook-up, clamping and installation Installation of Canopies/ Sunshades. (Supply of Canopies to be quoted separately) Cable and conductor identification and marking Continuity test from instruments to junction box . Complete Loop checking from Control Room. Support to be fabricated as per installation standards Contractor shall be responsible for protection of transmitters from rain after installation and rain protection adhesive aluminium tape to be wrapped on instrument terminal side. Grounding of Instruments. If required,making of temporary supports / scaffolding etc. is in contractor’s scope

INSTALLATION OF - Push Button, Ex d Approved

INSTALLATION OF - Gas Detectors -HC, IR Type , Ex d Approved

INSTALLATION OF - Gas Detectors -H2 ,Diffusion Catalytic Type, Ex d Approved

INSTALLATION OF - Hooter, Ex d Approved

INSTALLATION OF - Beacons, Ex d Approved

INSTALLATION OF - Linear Heat sensing cable along with retractable cable for all 5Nos of Tanks (Paraxylene Tanks) with JB & accessories

INSTALLATION OF - Linear Heat sensing cable along with retractable cable for all 8Nos of ISBL Tanks with JB & accessories

INSTALLATION OF - EOL JB's for LHS Cables

INSTALLATION OF - Manual Call point with canopy (Break Glass, Conventional Ex-proof, Ex d, 24 VDC Power Supply, Die Cast Aluminium Housing Material, ATEX / IECEx & CCOE / PESO approvals, SS 316 Mounting Accessories), Ex d Approved

INSTALLATION OF - AFR for Valves & other pneumatic devices with SS316 brackets & nuts bolts

SUPPLY OF PROXIMITY TYPE LIMIT SWICTHES ON MANUAL VALVES:

SUPPLY OF - Namur IS Limit switches for Manual Isolation Valves for Tanks (Paraxylene, Acetic, LSHS,Diesel) asper MB LAL.All Mounting accessories shall be SS316

INSTALLATION OF PROXIMITY TYPE LIMIT SWICTHES ON MANUAL VALVES: Scope of work includes Installation, hook-up & Testing of Proximity type limit switches along with SS Conduits & Junction Boxes. Taking delivery (including related handling) at on Site Contractor warehouse, onsite transportation, handling, temporary storage. Provide details to proximity Vendor for installation of Proximity switches on Manual Valves. Installation of Proximity switches on Manual Valves Functional Test.Prepare functional test reports Hook-up, clamping and installation of conduits & Junction boxes Cable and conductor identification and marking & connection Continuity test from instruments to junction box . Complete Loop checking from Control Room. Support to be fabricated Contractor shall be responsible for protection of transmitters from rain after installation and rain protection adhesive aluminium tape to be wrapped on instrument terminal side.

INSTALLATION OF - Namur IS Limit switches for Manual Isolation Valves for Tanks (Paraxylene, Acetic, LSHS,Diesel) asper MB LAL.All Mounting accessories shall be SS316

Scope of work includes Servicing,Calibration, healthiness check, hook-up & Testing of existing F&G Devices. Any spares required during performance of above activity will be provided by GMPL (as free issue material) Calibration & Functional Test (Health Test). OEM services along with all equipments, tools,materials required for calibration of items like gas cyclinders, tubing,etc shall be included in scope of supply. Prepare Calibration & functional test reports. Any spares required during performance of above activity will be provided by GMPL (as free issue material) Continuity test from instruments to junction box . Complete Loop checking from Control Room. Contractor shall be responsible for protection of transmitters from rain after installation and rain protection adhesive aluminium tape to be wrapped on instrument terminal side. Grounding of Instruments. If required,making of temporary supports / scaffolding etc. is in contractor’s scope

SERVICE,CAL AND INST OF- Manual Call points - (OEM: Baliga)

SERVICE,CAL AND INST OF- Hooters - (OEM: Baliga)

SERVICE,CAL AND INST OF- Beacons - (OEM: Baliga)

SERVICE,CAL AND INST OF- Toxic Gas Detector - (OEM: Drager)

SERVICE,CAL AND INST OF- HC Gas Detector (IR Point) (OEM :Honeywell | Optima-XNX)

SERVICE,CAL AND INST OF- HC Gas Detector (OEM :Honeywell , Model: XNX Transmitter + Optima Plus sensor)

SERVICE,CAL AND INST OF- H2 Gas Detector (OEM : Honeywell , Model: XNX Transmitter +MPD catalytic sensor)

SERVICE,CAL AND INST OF- O2 Gas Detector (OEM: Honeywell, Model:XNX Transmitter +XNX Sensor)

SERVICE,CAL AND INST OF- O2 Gas Detector inside Analsyer Shelter (OEM:Honeywell , Model SPXCD)

SERVICE,CAL AND INST OF- H2 Gas Detector inside Analsyer Shelter (OEM :Honeywell , Model SPXCD )

SERVICE,CAL AND INST OF- Toxic Detector (CO) inside Analsyer Shelter (OEM :Honeywell, Model SPXCD )

SERVICE,CAL AND INST OF- LEL Detcetor (CH4) inside Analsyer Shelter (OEM :Honeywell, Model SPXCD )

Scope of work includes Calibration,Installation, Hook-up & testing. Taking delivery (including related handling) at on Site Contractor warehouse, onsite transportation, handling, temporary storage. Freeissue from M/s GMPL. Calibration & FunctionalTesting. Provide Calibration Instruments for calibrating Instruments on returnable basis.Calibration equipment shall be certfied by certified agencies.Prepare Calibration & functional test reports Pots installation, if required Hook-up connection to the process line and to instruments and painting Hook-up, clamping and installation Hydro test of connection lines to the process In case of Remote seal Instruments, Fixing of Flanges / Diaphragm Seals to the Vessel / Equipment nozzle flanges, Proper supporting and routing of Capillaries by studying the route and fixing supports / angles / trays accordingly Installation of Canopies/ Sunshades. (Supply of Canopies to be quoted separately) Cable and conductor identification and marking Continuity test from instruments to junction box . Complete Loop checking from Control Room. Support to be fabricated as per installation standards Support Painting as per Project Specification. Contractor shall be responsible for protection of transmitters from rain after installation and rain protection adhesive aluminium tape to be wrapped on instrument terminal side.

CAL AND INST OF- Radar Type Level Transmitter -GWR

CAL AND INST OF- Ultrasonic Level transmitters for Sump

CAL AND INST OF- Pressure Transmitter with 2 valve manifold

CAL AND INST OF- D.P Type Pressure transmitter

CAL AND INST OF- Magnetic Level Gauge

CAL AND INST OF- Pressure Gauge - Normal type with 2 Valve Manifold

CAL AND INST OF- Diff.Pressure Gauge

CAL AND INST OF- Flow gauge

CAL AND INST OF- Flow Transmitter

CAL AND INST OF- Flow switch

CAL AND INST OF- Level Gauge

CAL AND INST OF- Local indicator

CAL AND INST OF- Level Transmitter

CAL AND INST OF- Level switch

CAL AND INST OF- Level transmitter ® (GWR)

CAL AND INST OF- Pressure Gauge

CAL AND INST OF- Temperature element + Thermowell

CAL AND INST OF- Temperature Gauge

CAL AND INST OF- Temperature Transmitter

CAL AND INST OF- Test Thermowell

CAL AND INST OF- Vibration Transmitter

CAL AND INST OF- Speed switch

CAL AND INST OF- Rotameter

Scope of work includes Removal,Calibration,Installation, Hook-up & testing. Taking delivery (including related handling) at on Site Contractor warehouse, onsite transportation, handling, temporary storage. Disconnecting of cables ,Tubes & removal of Instrument. Shifting of Instrument to Contractor warehouse. Calibration & FunctionalTesting. Provide Calibration Instruments for calibrating Instruments on returnable basis.Calibration equipment shall be certfied by certified agencies.Prepare Calibration & functional test reports Installation of Instruments Hook-up connection to the process line and to instruments and painting Hook-up, clamping and installation In case of Remote seal Instruments, Fixing of Flanges / Diaphragm Seals to the Vessel / Equipment nozzle flanges, Proper supporting and routing of Capillaries by studying the route and fixing supports / angles / trays accordingly Removal & Installation of Canopies/ Sunshades. (Supply of Canopies to be quoted separately) Cable and conductor identification and marking Continuity test from instruments to junction box . Complete Loop checking from Control Room. Contractor shall be responsible for protection of transmitters from rain after installation and rain protection adhesive aluminium tape to be wrapped on instrument terminal side. Making of temporary supports / scaffolding etc. is in contractor’s scope

CAL AND INST OF- Pressure Transmitter with 2 valve manifold

CAL AND INST OF- Diff.Pressure Transmitters with Manifolds

CAL AND INST OF- Pressure Gauges

CAL AND INST OF- Temperature Gauges

CAL AND INST OF- Temperature Elements

CAL AND INST OF- Temperature Transmitters

REMOVAL & REINSTALLATION OF INSTRUMENTS DURING PIPE TESTING: Scope involves removal, preserving & reinstallation of Instruments during pipe testing like Hydrotest, chemical test ,etc Removal of Instruments from pipeline during the pipeline testing like hydrotest,chemical test,etc.Any actvities like Tube removal & glanding & termination as neccessary to be carriedout by contractor Wrapping of instruments in polythene cover.Polythene cover to be provided by contractor Reinstallation of Instruments with proper hook-up of Tubes & cables If required,making of temporary supports / scaffolding etc. is in contractor’s scope.

REM AND INST OF- Temperature Element

REM AND INST OF- Temperature Gauges

REM AND INST OF- Diaphragm Transmitters

REM AND INST OF- Level Gauges

REM AND INST OF- GWR/ Magnetic Level Transmitter

REM AND INST OF- Diaphragm seal Pressure Gauges

REM AND INST OF- Level Switches

SUPERVISION FOR CAL,HOOKUP, INST AND TESTING OF - PCV

SUPERVISION FOR CAL,HOOKUP, INST AND TESTING OF - Motorized Operated Valves

SUPERVISION FOR CAL,HOOKUP, INST AND TESTING OF - Control Valve

SUPERVISION FOR CAL,HOOKUP, INST AND TESTING OF - ON-OFF Valve

TESTING OF SAFETY VALVES: Withdrwal form stores / laydown area / site installed postions , Transportation to and from test facilities . Freeissue from M/s GMPL. Contractor shall carry out safety relief valve (various sizes & pressure rating) set pressure check using adequate test bench. Safety relief valve pressure setting shall be as per specification (if required contractor shall adjust spring) . Contractor shall also check seat tightness in accordance with API- 527. Providing and installing the calibration tags for PSV. Testing of the Safety Valves (various sizes) shall be done with water . (for liquid service) & with nitrogen (for steam & vapour service) Hydraulic pump, test bench, nitrogen cylinders, regulators and other accessories required are to be supplied by Contractor. Test Bench shall be approved by Third Party agency. Testing and recording (Reporting). Contractor shall include Testing & calibration of each PSV X 2 Times with span of 6 months from 1st Testing & calibration

TESTING AND - Calibration of PSV upto 4"

TESTING AND - Calibration of PSV above 4"

INSTALLATION OF CANNOPIES : Taking delivery (including related handling) at on Site Contractor warehouse, on-site transportation, handling, temporary storage. Freeissue from M/s GMPL. Temporary shifting /Handling of existing cables,trays,Instruments & tubes to carryout the work asper requirement. Restore of existing cables,trays,Instruments & tubes after completion of work. Required Fabrication work, if any . If required,making of temporary supports / scaffolding etc. is in contractor’s scope.

INSTALLATION OF - Canopies for Transmitters & above F&G items

INSTALLATION OF - Canopies for JB

SUPPLY OF MISSC ITEMS:

SUPPLY OF - Powder cotted UV resistant SS Tie for cable dressing-Sizes-300mm - Pack of 100 nos

SUPPLY OF - Powder cotted UV resistant SS Tie for cable dressing-Sizes 150mm - Pack of 100 nos

SUPPLY OF - Powder cotted UV resistant SS Tie for cable dressing-Sizes-100mm - Pack of 100 nos

SUPPLY OF - SS 316 Tube Clamps (approxmate qty.) 1/2"

SUPPLY OF - Cable lug (Consumable) (approxmate qty.) 0.75mm Boot lug Al

SUPPLY OF - Cable lug (Consumable) (approxmate qty.) 1.5mm Boot Lug Al

SUPPLY OF - Cable lug (Consumable) (approxmate qty.) 2.5mm Boot Lug Al

SUPPLY OF - JB Synthetic rubber Gasket (approxmate qty.) 20MM WidthX 6MMThick

SUPPLY OF - JB Bolts (approxmate qty.) M6 X 35MM Long including head (Allen bolt)(30 MM long Threads and head 5mm).MOC:SS316

SUPPLY OF - Cable Tray Clamps for GI 150MM W Perforated GI Cable Tray with Bolts

SUPPLY OF - Cable Tray Clamps for GI 300MM W Perforated GI Cable Tray with Bolts

SUPPLY OF - Cable tray couplers (GI) : For coupler plate 70mm (ht) x 210mm Long for 100mm, 150mm & 300m wide tray , (Each Set shall consist of 1 No of GI coupler + 8Nos of SS316 nut bolt + 16Nos of SS316 plain washer)

SUPPLY OF - Cable tray couplers (GI) : For coupler plate 25mm (ht) x 210mm Long for 50mm wide tray , (Each Set shall consist of 1 No of GI coupler + 4Nos of SS316 nut bolt + 8Nos of SS316 plain washer)

SUPPLY OF - SS316 Nut bolts with double washers with one spring washer size

SUPPLY OF - SS 316 Tag plats for cables and instrument air header (approxmate qty.) Sizes for multicore-110MM (L) X 25MM (W) and Branch cable & air header -90MM(L) X 20 MM(W)

SUPPLY OF - Ball valves handles 1/2"

SUPPLY OF - Limit switch mounting clamps, SS (Including Fabrication).All mounting accessories shall be SS316

SUPPLY OF - AFR mounting clamp, SS 316(Including Fabrication)

SUPPLY OF - 1" SS 316 'U' clamps with nuts

SUPPLY OF - 1.5" SS 316 'U' clamps with nuts

SUPPLY OF - 2" SS 316 'U' clamps with nuts

INSTALLATION OF MISCELLANEOUS ACTVITIES: Installation of miscellaneous items as listed below & include fabrication wherever required. Site survey , if required , to arrange necessary materials. Taking delivery (including related handling) at on Site Contractor warehouse, on-site transportation, handling, temporary storage. Temporary shifting /Handling of existing cables,trays,Instruments & tubes to carryout the work asper requirement. Any fabrication required to fix or installatation.Drilling , filing,cutting etc for removal of existing & fixing of new coupler plates in existing installed Trays. Painting . Restore of existing cables,trays,Instruments & tubes after completion of work. Required Fabrication work for clamps & mounting accessories. If required,making of temporary supports / scaffolding etc. is in contractor’s scope.

INSTALLATION OF - Powder cotted UV resistant SS Tie for cable dressing-Sizes-300mm - Pack of 100 nos

INSTALLATION OF - Powder cotted UV resistant SS Tie for cable dressing-Sizes 150mm - Pack of 100 nos

INSTALLATION OF - Powder cotted UV resistant SS Tie for cable dressing-Sizes-100mm - Pack of 100 nos

INSTALLATION OF - SS 316 Tube Clamps (approxmate qty.) 1/2"

INSTALLATION OF - Cable lug (Consumable) (approxmate qty.) 0.75mm Boot lug Al

INSTALLATION OF - Cable lug (Consumable) (approxmate qty.) 1.5mm Boot Lug Al

INSTALLATION OF - Cable lug (Consumable) (approxmate qty.) 2.5mm Boot Lug Al

INSTALLATION OF - JB Synthetic rubber Gasket (approxmate qty.) 20MM WidthX 6MMThick

INSTALLATION OF - JB Bolts (approxmate qty.) M6 X 35MM Long including head (Allen bolt)(30 MM long Threads and head 5mm).MOC:SS316

INSTALLATION OF - Cable Tray Clamps for GI 150MM W Perforated GI Cable Tray with Bolts

INSTALLATION OF - Cable Tray Clamps for GI 300MM W Perforated GI Cable Tray with Bolts

INSTALLATION OF - Cable tray couplers (GI) : For coupler plate 70mm (ht) x 210mm Long for 100mm, 150mm & 300m wide tray , (Each Set shall consist of 1 No of GI coupler + 8Nos of SS316 nut bolt + 16Nos of SS316 plain washer)

INSTALLATION OF - Cable tray couplers (GI) : For coupler plate 25mm (ht) x 210mm Long for 50mm wide tray , (Each Set shall consist of 1 No of GI coupler + 4Nos of SS316 nut bolt + 8Nos of SS316 plain washer)

INSTALLATION OF - SS316 Nut bolts with double washers with one spring washer size

INSTALLATION OF - SS 316 Tag plats for cables and instrument air header (approxmate qty.) Sizes for multicore-110MM (L) X 25MM (W) and Branch cable & air header -90MM(L) X 20 MM(W)

INSTALLATION OF - Ball valves handles 1/2"

INSTALLATION OF - Limit switch mounting clamps, SS (Including Fabrication).All mounting accessories shall be SS316

INSTALLATION OF - AFR mounting clamp, SS 316(Including Fabrication)

INSTALLATION OF - 1" SS 316 'U' clamps with nuts

INSTALLATION OF - 1.5" SS 316 'U' clamps with nuts

INSTALLATION OF - 2" SS 316 'U' clamps with nuts

INSTALLATION OF MARSHALLING PANELS, IRP PANELS, PDB's & WORKSTATIONS: Scope includes taking delivery to on Site Contractor ware house or from place of storage to respective control rooms, on site transportation, handling, storage, unpacking etc. The other activates include the following operations: Freeissue from M/s GMPL. i) These cabinets contain delicate electronic hardware and display units. It should be handled carefully & should not be exposed to high temperature, sunlight, dust and water. ii) Align, fix & tighten the cabinets. SS Nuts & bolts required for fixing the cabinets on the frame are to be supplied by the contractor. For installation of the cabinets, if required, contractor shall also modify the false floor tiles. iii)Contractor shall ensure that all the cabinets are aligned and there is no vertical gap between various cabinets. iv)Contractor shall remove the gland plate from the cabinet and shall drill the gland plate for fixing the cable glands. After drilling the holes, contractor shall re-fix the gland plate in the cabinet. Gas cutting not permitted for making holes in the gland plate. Once cable laying is & termination is complete all the spare cable entries in gland plate shall be plugged by the contractor. vi) Install instrument, accessories, modules and other hardware supplied loose along with the cabinets under the supervision of manufacturer’s representative. vii)Inside the cabinet, through MCT / Glands contractor shall terminate all the loose wires. If required lugs shall also be supplied by the contractor. viii)Contractor shall check that is the cabinet there is no loose connections. ix)Cleaning, de-dusting, paint touch-up (if necessary), stenciling and maintenance of the cabinet. Contractor scope include supply of paint. x)earthing of the cabinet by means of copper wire connected to the general ground system of the control room shall be done by the contractor including supply of PVC insulated copper wire of adequate size as per the earthing layout drawing. xi)The contractor shall assist the system supplier’s representative for initial start-up and commissioning of the cabinets. xii) Any other wok not specified above but required for installation and commissioning of the cabinets is also in contractor’s scope of work.

INSTALLATION OF - Panels, Marshalling cabinets, IRP ,PDB

INSTALLATION OF - Workstation

RELOCATION OF MARSHALLING PANELS, IRP PANELS, PDB's : Scope includes relocation of Cabinets & its Baseframe. The other activates include the following operations: i) Disconnect of cabinets from Base frame. Ii) Relocate of cabinets within same building asper GMPL requirement. iii) Removal , modify & resinstall of Cabinet base frame & painting. iv) Removal & fixing of False flooring tiles.Any modification on false flooring tiles.

REMOVAL AND RELOCATION-- Removal & Relocate of 1200mm Wide Cabinets

REMOVAL ACTVITIES: If required,making of temporary supports / scaffolding etc. is in contractor’s scope. Temporary shifting /Handling of existing cables,trays,Instruments & tubes to carryout the removal work asper requirement. Drilling, grinding, welding & gascutting Restore of existing cables,trays,Instruments & tubes after completion of work. Shifting of debries & other materials to designated area.

REMOVAL OF - Removal of 50mm to 150mm perforated Cable trays

REMOVAL OF - Removal of 200mm to 300mm perforated Cable trays

REMOVAL OF - Removal of 600mm & above cable trays

REMOVAL OF - Removal of Branch cables along with glanding & termination

REMOVAL OF - Removal of Main cables along with glanding & termination

REMOVAL OF - Removal of Tubes & Tube fittings

REMOVAL OF - Removal of Transmitters along with glanding & termination

REMOVAL OF - Removal of Tray supprots, tubes supports , instrument supports

FIBER OPTIC CABLE TERMINATION & INSTALLATION OF PANEL FOR 2NOS OF NEW BAGGING MACHINE Scope includes supplies FO Cables & 12port fully loaded (pigtail) patch panel and Patch Cords Taking delivery (including related handling) at on Site Contractor warehouse, on-site transportation, handling, temporary storage. Cables termination on patch panel Cable and conductor identification and marking. Cables setting inside panels, terminal execution and connection at both ends OTDR to be done twice (along with drum before laying & after splicing) Splicing shall be in Sub-Contractor scope OTDR reports to be provided Cable Tag Plate (SS 316) to be provided at both ends Inspection and tests (OTDR) Patch Panel Taking delivery (including related handling) at warehouse, on-site transportation, handling, temporary storage. Equipment erection, alignment and fixing and stenciling on Panels. Alignment of false floor after cable trays and cables installation Adequate protection for Patch Panels, during installation and connection activities Inspection and tests

SUPPLY OF - 12C , Armoured FO Cable

SUPPLY OF - 12port full loaded with pig tail, LIU

SUPPLY OF - Patch Cord

FIBER OPTIC CABLE TERMINATION & INSTALLATION OF PANEL FOR 2NOS OF NEW BAGGING MACHINE Taking delivery (including related handling) at on Site Contractor warehouse, on-site transportation, handling, temporary storage. Cables termination on patch panel Cable and conductor identification and marking. Cables setting inside panels, terminal execution and connection at both ends OTDR to be done twice (along with drum before laying & after splicing) Splicing shall be in Sub-Contractor scope OTDR reports to be provided Cable Tag Plate (SS 316) to be provided at both ends Inspection and tests (OTDR) Patch Panel Taking delivery (including related handling) at warehouse, on-site transportation, handling, temporary storage. Equipment erection, alignment and fixing and stenciling on Panels. Alignment of false floor after cable trays and cables installation Adequate protection for Patch Panels, during installation and connection activities Inspection and tests

INSTALLATION OF - 12C , Armoured FO Cable

INSTALLATION OF - 12port full loaded with pig tail, LIU

INSTALLATION OF - Fiber termination (single mode) (per strand)

INSTALLATION OF - OTDR Test

INSTALLATION OF - Patch Cord

INSTALLATION OF LOCAL PANEL FOR FOAM PACKAGE,STP,DRINKING WATER SYSTEM,CLO2,ETC: Taking delivery (including related handling) at on site Contrcator warehouse, on-site transportation, handling, temporary storage. Freeissue from M/s GMPL. Local panel shall be Freeissue to Contractor by M/s GMPL Local panels installation including Supply of the grouting, Bolts & Masonry works etc. Study of cable and pneumatic transmission routing Panels grounding Cable glands and sealing installation on local panels Installation of local panel loose instruments Wiring and connections restoration Continuity test of all connections Panels power on and functional tests Stenciling and Painting as per Project Specification Adequate protection for LCP, during installation and connection activities Subcontractor shall remove the gland plate from the cabinet, shall drill the gland plate for fixing cable glands etc Installation of local panel loose Canopy (2.5 mm thick GI sheet)

INSTALLATION OF - Local Panel

INSTALLATION OF SHELTER FOR CAAQMS: Taking delivery (including related handling) at on site Contrcator warehouse, on-site transportation, handling, temporary storage. Freeissue from M/s GMPL. Any requirement of Crane arrangement, Fork lifter ,etc to be arranged by contractor for Shifting, lifting & installation purpose. Fabrication of Support steel, installation and painting of all supports required Shelter/Cabinet /Rack positioning and fixing to the anchor bolts provided on the concrete base along with Masonry work, Alignment of Shelter. Installation and connection of all utilities to the shelter Installation and connection of output signals to existing junction boxes inside or outside the shelter Continuity test for electronic and pneumatic signals Shelter /Cabinet /Rack and analyzers grounding, by means of a connection, to the general grounding network Installation of those parts provided loosen for shipping reason (e.g. canopies, bottles, air conditioned unit,Clean agent etc.) Loose Supplied items shall be Installed & Interconnected. Shelter is provided with MCT for cable entry.Contractor to lay cable through MCT. Contractor to consider all the activities associated with cable pulling through MCT Assistance to Vendor Specialist of analysers for power-up, calibration, loop test operations and Site Acceptance Test. Inspection and test

INSTALLATION OF - 5000mm(L) X 4000MM(W) X 3000MM(Ht) Pre fabricated Metallic Analsyer House for CAAQM Station

SERVICING OF LOCAL PANELS Scope includes survey of panels at site, installation of accessories Exact Dimensions to be verified by bidder by visiting site after successful bid. Following actvities shall be carried-out as applicables 1. Change of Locks 2. Change of hinges 3. Installation of Canopy 4. Painting of panels 5. Proper sealing of panels

SERVICING OF- No of Local panels for servicing (Approx Size of panel: 2.5Mtrs (W) X 2Mtrs(Ht.) .

SUPPLY OF ACCESSORIES FOR SERVICING OF PANEL AS PER ATTACHED DRAWING.Scope includes survey of panels at site, procurement of accessories Exact Dimensions to be verified by bidder by visiting site after successful bid.Following accessories to be supplied 1. Supply of Locks 2. Supply of hinges 3. Supply of Canopy 4. Supply of Paint of panels 5. Supply of Proper seal of panels

SUPPLY OF ACCESSORIES FOR SERVICING OF PANEL

BRIDGE AND ROOF COMPANY INDIA LIMITED (BID ID -839247)

M/s HAL Offshore Limited (BID ID -839241)

BRIDGE AND ROOF COMPANY INDIA LIMITED (BID ID -839247)

BRIDGE AND ROOF COMPANY INDIA LIMITED (BID ID -839247)

M/s HAL Offshore Limited (BID ID -839241)

BRIDGE AND ROOF COMPANY INDIA LIMITED (BID ID -839247)

M/s HAL Offshore Limited (BID ID -839241)

BRIDGE AND ROOF COMPANY INDIA LIMITED (BID ID -839247)

M/s HAL Offshore Limited (BID ID -839241)

BRIDGE AND ROOF COMPANY INDIA LIMITED (BID ID -839247)

M/s HAL Offshore Limited (BID ID -839241)

BRIDGE AND ROOF COMPANY INDIA LIMITED (BID ID -839247)

BRIDGE AND ROOF COMPANY INDIA LIMITED (BID ID -839247)

M/s HAL Offshore Limited (BID ID -839241)

BRIDGE AND ROOF COMPANY INDIA LIMITED (BID ID -839247)

M/s HAL Offshore Limited (BID ID -839241)

BRIDGE AND ROOF COMPANY INDIA LIMITED (BID ID -839247)

M/s HAL Offshore Limited (BID ID -839241)