PERIODICAL SERIVCES TILING PLASTERING PLUMBING JOINERY AND ALLIED

Amount

Demolition of cement concrete in ground floor and paving n exc 15cm below or above ground level and removing debris outside MD land complete all as specified.

M&L 75mm thick PCC type D-2, (1:4:8) using 40mm graded stone aggregate as in sub base of floor/ paving

M&L 25 mm thick PCC 1 : 2 : 4 type B0 (using 12.50 mm graded stone aggregate) as floor finished rough to receive tile screed/bedding layer complete all as specified and directed

Material and labour for 75mm thick PCC (1:3:6) type C-1 using 20mm graded crushed stone aggregate as in paving/plinth protection/ Hard standing laid in panels and joints filled with mix of bitumen and sand (1:3) by weight, finished the surface even and fair without using extra cement complete all as specified and directed.

M&L PCC 1 : 2 : 4 type B1 (using 20 mm graded stone aggregate) and levelling to required thickness on roof including weathering slightly rounded all as specified and as directed

Demolition of Brickwork or PCC Block built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles

M&L precast cement concrete block masonry with solid block, type C-1,1:3:6 mix ( using 20mm graded aggregate ), exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in any description and in any position as in sunken floors, coping, benching, padding etc including removing debris from MD land complete all as specified and directed.

M&L for PCC 1:5:10 type E2 (using 40 mm graded stone aggregate) any thick, in as in sub base of the sunken floors complete all as specified and directed.

M & L Rendering 15mm thick in CM 1 : 3 on brick/concrete surface finished fair and even mixed with water proofing liquid complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid separately under respective item of this Schedule.

M&L for Providing 1.00mm thick BRUSHBOND RFX GREY (which is a two component acrylic polymer modified cementitious coating which shall consists of Brushbond RFX powder and Brushbond RFX liquid acrylic emulsion), grey in colour, of M/s FOSROC, applied using stiff brush, roller or trowel to obtain the desired thickness on plastered surface in sunken floor, all as per manufacturers instructions, complete all as specified and directed.

M & L Rendering 10mm thick in CM 1 : 4 on concrete surface even and smooth on roof surface incl water proof liquid finished when concrete is green complete all as specified and directed. NOTE:- Water proofing compound shall be measured and paid separately under respective item of this Schedule.

Supply only liquid water proofing compound

Demolition of RCC cover slab of any description & in any position and removing debris outside MD land complete all as specified.

M&L for TMT bars 10mm dia and above cut to length bent to shape required inclding cranking, bending etc and binding with mild steel wire (annealed) not less than 0.90mm dia complete all as specified.

M&L Precast RCC 1:2:4 type B1 using 20mm stone aggregate as in cover slab of manhole, gully trap, drain etc. set in CM 1:4 all as specified and as directed.

Demolition of floor, hearth or wall tiling including cement mortar bedding (including backing), removing serviceable tiles and disposing off debris to outside the MOD land all as specified and as directed.

M&L Non-skid coloured ceramic tiles 7 to 8 mm thick, area of each tile exceeding 0.06 sqm but not exceeding 0.11sqm, as in floor set and jointed in neat cement slurry and pointed in white cement mixed with colouring pigment to match colour of tiles over and including 15mm thick screed bed of CM 1:4 complete all as specified and as directed.

M&L joint free non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.

M&L joint free non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in Skirting /dado set and pointed in coloured cement to match coloured tiles laid over and including backing coat of 10mm thick rendering in CM 1:3 complete all as specfied and directed.

M&L non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.

M&L non-skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10mm thick rendering in CM (1:3) complete all as specfied and directed.

M&L glazed ceremic tiles in vertical surfaces 300x450x7mm thick, set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:3) complete all as specfied and directed.

Renewing glazed ceramic tiles of any type and size in patches area not exceeding 5 Sqm including removing and cleaning old tiles, preparing the beds and laying of new tiles of same size/type/description, setting, jointing, pointing etc matching with the existing surface over and including 10mm thick backing coat in CM 1:3 complete all as specified and directed

Dismantling of Stone slabs & tiles of any description or thickness in floors, aprons etc. Laid, bedded & pointed in any mortar and removing debris outside MD land omplete all as specified.

S&F Chequered cement concrete commercial Tiles 25cm x 25cm x 20 to 22mm /30cmx30cmx20 to 25mm thick with grey cement and pigment set jointed and pointed in neat cement slurry in floors and cut and polished, laid over and including 20mm Screed in CM 1:4 all as specified and as directed.

M&L for 20mm thick Granite work (of any type) (table rubbed and premirror polished) in single piece in steps, jambs, pillars, window-cills, cooking platforms and like in cement mortar (1:4) including pointing in cement white (1:2) using marble dust with admixture of pigment to match the shade of granite, including making hole for gas pipe ,laid over and including 15mm thick screed bed in CM 1:4 complete all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

Machine cut kota stone, 20-25 mm thick, over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including a screed bed of 20mm thick in CM 1:4

Kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete including 10mm thick backing coat in CM 1:3

Taking down cement plastering of any thickness on brick, concrete or stone walls, partitions, ceilings etc including raking out joints, hacking for key, scrubbing down with water etc, removal of rubbish off the premises.

M&L for 10mm thick rendering on brick or concrete surface in cement mortar 1:6 and finishing the surface with even and smooth without using extra cement all as specified and as directed.

M&L for 15mm thick rendering on brick or concrete surface in cement mortar 1:4 and finishing the surface with even and smooth without using extra cement all as specified and as directed. Note: Water proofing compound shall be measured and paid seperately

M&L for 5mm thick rendering on ceilings in cement mortar 1:3 and finishing the surface even and smooth without using extra cement all as specified and as directed.

Preparing the newly plastered surfaces of walls and applying two coat of oil bound distemper over a coat of alkali reistant primer over 1.00mm thick wall care puty complete all as specified and directed.

Preparing the newly plastered surfaces of ceilings and applying two coats of oil bound distemper over alkali-resistant primer and 1.00mm thick wall care putty complete all as specified and directed.

Material & Labour for preparation of newly plastered surface and applying two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV Resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm complete all as specified and as directed.

M&L Preparing the surfaces of old wall surfaces and applying one coat of distemper oil emulsion complete all as specified and directed

M&L Preparing the old plastered ceiling surfaces and applying one coat of distemper oil emulsion complete all as specified and directed

Preparation of old plastered sufaces of walls and applying one coat of weather-proof antifungal exterior emulsion paint , complete all as specified and directed.

M&L Preparation of old wooden surfaces and applying a coat of synthetic enamel paint over 10 cm width or girth complete all as specified and as directed.

M & L for painting of old steel surfaces of any description not otherwise described over 10 cm width or grith with one coats of synthetic enamel paint including preparation of surfaces etc complete all as specified and as directed.

M&L Complete removal of existing treatment and preparing the surfaces of walls plastered or unplastered and applying two coat of distemper oil emulsion over a coat of alkali resistent primer over 1mm putty. complete all as specified and directed

M&L Complete removal of existing treatment and preparing the surfaces of ceilings plastered or unplastered and applying two coats of distemper oil emulsion over a coat of alkali resistent primer over 1mm putty. complete all as specified and directed

Dismantling Plain or corrugated steel sheeting,any gauge, thickness

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified

Dismantling wrought iron of mild steel work of any description not otherwise provided for complete all as specified and as directed by the Engineer-in-Charge.

S&F Framed work such as grills, gratings and similar work etc., with ends of bars shouldered and/or riveted, or forged into spikes; ; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165

Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165

S& F Collapsible steel gates, top hung, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc., as specified, erected in position and securing runners with holdfasts and brackets, complete

M&L two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel surfaces of any description over 10 cm width or girth including preparation of surfaces all as specified and as directed..

Taking down chowkats or frame without taking off shutter from the frame n.exc 1.50 Sqm each complete all as specified and directed.

Taking down chowkats / frame without taking of shutter from the frame exc 1.50 Sqm n.exc 4 Sqm each. complete all as specified and directed.

Taking down Shutters of any description exc 1 sq. m and n exc 2 sq. m each

Repair to steel window/ ventilators shutter (area not exceeding 0.60 Sqm) of any description including replacing unserviceable handles, hinges, peg stay etc of any type/pattern and making window/ventilator shutter absolutely working condition including necessary welding if required complete all as specified and directed.

S & F pressed steel frames of size 105 x 60mm x 1.25 mm thick for door with one or more rebates, including necessary fixing lugs, hinges lock strike plate etc complete all as specified and as directed.

M & L PCC 1:3:6 type C0 using 12.5mm graded stone aggregated as in filling the chowkats/frames complete all as specified and as directed.

S & F 35 mm thick plain framed panelled factory made shutters(two panel) with IInd class hardwood rail and style with lock rail and panel of 12 mm BWP commercial ply with commercial vaneer on both faces. The size of rail and style as per IS - 1003 Part - I , kiln seasoned and chemically pressure treatedcomplete all as specified and as directed.

S & F 35mm thick IInd class hardwood glazed and skeleton shutters open rebated and prepared to receive gauge (without sash bars)edges of framing plain, chamfered or round fitted with cut and mitred beads for securing wire gauge sizes of members as specified in SSR Part-I section 8 clase 8.24(a) of shutters all as specified and as directed.

M & L for Taking down wooden door shutter of any description and easing and adjusting and also refixing , area of shutter exceeding 1.00 Sqm but not exceeding 2.00 Sqm each, including making good the disturbed area as per existing, complete all as specified and directed.

Supply and fix Solid PVC door frame of size 50 mm x 47 mm made out of 5 mm plain colour PVC sheet reiforced with MS square tube supplying and fixing in opening as per specification and drawings.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles & plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame welded/ sealed to the stiles, & rails with suitable PVC sheet beading, & joined together with solvent cement, in the frame at site as per specification & drawing.

M & L for applying two coats of synthetic enamel paint over a coat of pink primer including preparation of previously untreated or new wooden surfaces exc 10 cm in width or girth complete all as specified and as directed.

S & F Aluminium anodised barrel tower bolts of extruded section, 150 mm long all as specified and as directed.

S&F mild steel butt hinges medium weight cold rolled of size 100 mm including necessary welding complete all as specified and directed.

S&F SS butt hinges medium weight of size 100 mm complete all as specified and directed.

S&F Single action spring hinges, mild steel with steel wire spring, stove enameled black, 100mm size including necessary welding fixed to steel door frame complete all as specified and directed.

S & F Aluminium anodised cast type handles 150mm long all as specified and as directed.

S & F Aluminium anodised cast type handles 100mm long all as specified and as directed.

S & F aluminium alloy, anodised, sliding door bolt with hasp, staple bolt type and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections 300 mm long all as specified and as directed.

S & F in repair door stopper of rubber and aluminium alloy body, 150 mm size fixed all as specified and as directed.

Taking down boards of any description and any size as in shelves complete all as specified and directed.

18/19mm thick one side prelaminated particle board, interior grade, with decorative choice lamination and fixed with screws to steel/timber frame work complete all as specified and directed

S & F external teak wood lipping, 6mm thick fixed with nails to particle board

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with width of flaps (When open) 30 mm

S & F 18/ 19 mm thick fire retardant plywood BWR type including cutting, jointing, fixing with screws as in Cupboard doors and shelves complete all as specified and as directed.

M & L 0.90 mm thick decorative laminate Type 1 of surface finish, colour and pattern as approved fixed with approved adhesive as per manufacturer’s instructions complete all as specified and as directed

S&F SS butt hinges medium weight of size 75 mm complete all as specified and directed.

S & F fancy type stainless steel handle of size 100 mm long complete all as specified and as directed

S & F Magnetic ball catches of standard type fixed complete all as specified and as directed

Taking down steel window with frame without taking off shutter (double leaf /triple leaf shutter with frame ie. fly-proof and glazed)from the frame n.exc 0.60 Sqm each including glass panes. mosquito proof mesh all as specified and directed.

Taking down steel window with frame without taking off shutter (double/triple leaf double shutter with frame ie. glazed and fly-proof )from the frame exc 0.60 Sqm and not exc 3.0 sqm each including glass panes. mosquito proof mesh all as specified and directed.

S & F Powder coated aluminium frame/shutter for doors, windows, ventilators with one or more rebates including joining cleat for fixing, rubber neoprene packing for fixing, including minor fitting like lock, handle, roller for sliding etc. complete all as specified Note :- 1. For payment purpose weight of aluminium section shall be only measured. 2. Cost of aluminum mongry, lock, rubber packing, roller for sliding are included in the quoted rate. 3. Sheet glass and wire gauge shall be measured and paid separately.

S & F 4 mm thick sheet glass ordinary quality and glazing with oil putty and necessary clips as squares n exc. 0.5 Sqm in each pane complete all as specified and directed.

S & F 4mm thick pin head glass and glazing with oil puttyand necessary clips as square n exc. 0.5 Sqm in each pane complete all as specified and directed.

S&F Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F in repair Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples fixed in repair complete all as specified and directed.

Hacking out old broken glass (any thicknesss, size,quality or description) from metal frame inlcuding punching or drilling out old glazing pins/spring clips

Supply and fix in repair PVC waste pipe 32mm bore not less than 800mm long complete all as specified and direceted

S & F CP peg set (set of six) fancy type (as approved by GE) fixed with screwes fixed in repair complete all as specified and as directed

S & F GI Tubing medium grade of size 15mm with all fitting fixed to wall/Ceiling or laid on floor in short lengths including taking down old GI tubing complete all as specified and as directed.

S & F GI Tubing medium grade of size 20mm with all fitting fixed to wall/Ceiling or laid on floor in short lengths including taking down old GI tubing complete all as specified and as directed.

Cutting chases pinning in making good for brick walls to facing where required and pointing in cement mortor 1:3 to ends or edges of concealed water tubing and similar work including making good cutting not exc 10CM girth.complete all as specified and directed.

S & F in repair 15 mm CP cast copper alloy bib taps fancy type screwed down, screwed for iron pipe or for brass ferrule including taking down old bib taps complete all as specified and as directed.

S & F in repair 15 mm pillar taps, cast copper alloy fancy type , chromium plated screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe including taking down old pillar taps complete all as specified and as directed.

S & F in repair 15 mm CP stop valve fancy type with long shank and cup (concealed) type cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union all as specified and as directed.

S & F in repairs CP fancy type angle cock, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

S & F in repair fancy type chromium plated 2 way bib tap 15mm dia with CP flange as all as specified and as directed.

Supply and fix in repair chromium plated overhead shower rose 125 mm dia with swivel joints with and including overhead shower arm 230mm with wall flange , complete all as specified and directed by GE.

S&F in repair Single towel rail brass chromium plated 600mm long fixed with chromium plated screw and PVC cleat fixed in repair etc complete all as specified and directed.

S & F in repair Chromium plated fancy type brass soap dish with wall hook complete all as specified and as directed.

Supply and fix in repair Stainless steel toilet paper holder with flap guard, fixed to wall with CP brass screws and PVC cleat, complete all as specified and directed by GE.

S & F in repair PVC connecting pipe 600mm long 15 mm dia both end having brass coupling nut and PVC washer all as specified and as directed.

S&F Hand shower (Health Faucet) with 8mm dia, 1.2m long flexible tube in chrome finish and wall hook with NRV (Back flow preventer) fixed in position to wall, fixed in repair complete all as specified and directed by GE. Make : Cat part No ALD-577 of Jaquar or techno-commercial equivalent model in other makes as approved by GE”

S&F Vitreous china white wash down water closet pan (pedestal pattern) with PP soft closing seat cover, hinges, fixing accessories set (excluding flushing cistern and flush pipe), including UPVC (SWR) ‘P’ or ‘S’ trap and connection to drain (or outgoing pipe) and to flush pipe, antisyphonic pipe fixed in repair including dismantling existing water closet etc complete all as specified and directed by GE”

S&F for Vitreous china White Squatting Orissa Pattern pan of size 580x440mm, including UPVC ‘P’ or ‘S’ trap, front or back inlet and integral foot rests and making connection to trap and to flushing pipe, anti syphonic pipe, fixed in repair including dismantling existing squatting pan and making good to disturbed floor, complete all as specified and directed.

S & F PVC 10 Ltr capacity flushing cistern white, inlet, ball valve, float and handle on existing brackets and jointing with existing flush pipe and making good to the disturbed surfaces including dismantling of unserviceable flushing cistern complete all as specified and directed.

S& F Vitreous China wash basin, white, flat back, size 550x400mm excluding waste, chain and plug and porcelain stopper but including brackets, including Waste coupling of PTMT(half or full threaded) (Minimumweight 32mm-45gms/40mm-60 gms) with 32mm bore PVC waste pipe minimum 800mm long with inlet and outlet screwed for pipe or connections including necessary packing, union and cap and fixed in repairs complete all as specified and as directed.

S & F in repair stainless steel sink with draining board, made out of 1.00 mm thick sheet for kitchen with plugs, waste pipe and washer’s including cast iron cantilever brackets, connecting union etc over all size 915 mm x 460 mm with bowl size 410 x 330 x 160 mm including taking down old steel sink all as specified and as directed.

S&F in repairs Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (min.), with grating & union for discharge pipe& waste pipe (excluding flushing cistern)

S & F rotational moulded polyethylene water storage tanks three layered (cylindrical, vertical with closed top ) hoisted and fixed in position of 500 Ltrs capacity including taking down old one all as specified and as directed.

S & F rotational moulded polyethylene water storage tanks three layered (cylindrical, vertical with closed top ) hoisted and fixed in position of 750 Ltrs capacity including taking down old one all as specified and as directed.

S & F rotational moulded polyethylene water storage tanks three layered (cylindrical, vertical with closed top ) hoisted and fixed in position of 1000 Ltrs capacity including taking down old one all as specified and as directed.

Uprooting scrubs/plant/flora & fauna on wall girth not exceeding 100mm from brick wall by cutting holes into masonry/walls for digging out roots and dosing Sulfuric/Phenolic Acid as per manufacturer's instruction to burn deep rooted tree roots and making good the disturbed area with cement mortar in CM 1:3 using water proofing compound including necessary scaffolding upto a height of 16 metre complete all as specified and directed..

S&F in repair Ball valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball scrured for iron pipe of dia 20 mm bore complete all as specified and directed .

M & L in repair Gun metal Gate valves 20 mm dia with iron wheel head, screwed both ends for iron pipe and fixed including cutting the old pipes as in repair complete all as specified and directed

S & F (SWR) UPVC pipes 110 mm dia single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil waste/vent pipes including taking up or down existing PVC pipes and connections complete all as specified and as directed..

S & F (SWR) UPVC pipes 75mm dia single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil waste/vent pipes including taking up or down existing PVC pipes and connections complete all as specified and as directed..

S & F (SWR) UPVC pipes 40 mm dia single socketed in any length with solvent cement joints laid under floor or on walls fixed as soil waste/vent pipes including taking up or down existing PVC pipes and connections complete all as specified and as directed..

S&F in repair PVC floor trap/nani trap with plain/single hole CP grating including jointing to waste pipe in cement joint, of outlet 75 mm.dia .

S & F 75mm dia outlet PVC multi floor trap with CP grating including dismantling the damaged trap all as specified and as directed.

S & F PVC (SWR) bends any radius 75 mm dia of bore,with acess door including taking down old bends all as specified and as directed.

S & F PVC (SWR) bends any radius 110 mm dia of bore, with acess door including taking down old bends all as specified and as directed.

S&F PVC (SWR) branch piece,single (single Y) equal or unequal with acess door

S & F PVC (SWR) vent cowl of bore 110 mm dia, including taking down old PVC vent cowl all as specified and as directed.

Grinding and polishing to existing terrazzo flooring including wax polishing complete all as specified and as directed.

Disconnecting existing PVC water tank of capacity exc 500 ltrs but not exc 1000 ltrs fixed on foor by setting aside (or lowering, if required) for cleaning and removing all scale and dirt from tanks and from mouths of circlating pipes etc and hoisting/refixing/ reconnecting in same/new position including writing date of cleaning on each tank with white paint with height/size of letters/figures not less than 10cm and refixing existing servicable ball valves complete all as specified and directed

VARALAKSHMI CONSTRUCTIONS

SREE BUILDERS

SCION ENTERPRISES

VP DEVELOPERS AND CONTRACTOR