GRAM MAN NAGLA ISTITH RAMTAL ASHRAM KE PAS VRADHA ASHRAM GRAH KA NIRMAN KARY

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil as per SI.No. 2.8.1

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration as per SI.No. 2.35.3.1

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-lll) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from natural sources) As per SI no. 4.1.8

Brick work with common burnt clay (non modular) bricks of class -150 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand) as per SI No- 6.1.2

Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level in :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) as SI No-5.1.2

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete. (Under Floor) as per SI.No. 2.25 (a)

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete. (Under Floor) as per SI no 2.27

Brick work with common burnt clay bricks of M-150 Class in super structure above plinth level upto floor V level in all shapes and sizes in cement mortar 1:4 ( 1 cement : 4 coarse sand ) as per SI no 6.4.1

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone-lll) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) Upto Plinth Lvl as SI No-5.1.2

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) Above Plinth Lvl as SI No-5.2.2

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III)derived from natural sources : 3 graded stone aggregate 20 mm nominal sizederived from natural sources). Above Plinth Lvl as SI No-5.3

Steel reinforcement for R.C.C. work ready to use "cut and bend" rebars of approved make from factory/workshop to construction site including placing in position and binding all complete in Thermo-Mechanically Treated bars of grade Fe-500D or more. As per SI. No.- 5.22 B.1

Providing and fixing angle iron frames for doors, windows and ventilators of mild steel Angle sections of size 35x35x5 mm, joints mitred and welded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existing T-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer, all complete as per the direction of Engineer-In-charge. M.S. Angle 35x35x5 for door frames as per SI no. 10.31

12 mm thick cement plaster of mix 1:6 ( 1 cement & 6 course sand ) Outer Side as per IS 13.4.2

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone ) finished with floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. 40 mm thick floor 20 mm nominal size stone aggregate. As SI No. 11.3.1

P/F of Glass Strips of 5.5 mm Thick and 3.5cm Depth in flooring i/c all complt.SI No 631(a).

Finishing walls with Acrylic Smooth exterior paint of required shade: New work (Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) as per Sl no. -13.46.1 Two Coats

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gram/litre, of approved manufacturer and of required shade and colour all complete to achieve even shade and colour : New work (two or more coats) over and including water thinnable priming coat with cement primer having VOC content less than 50 gram/litre as per Sl no. -13.41.1 Two Coats

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture as per Sl no. -13.62.1

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer,over the plasterd wall surface even and smooth surface as per Sl no. -13.80

Providing and laying vitrified floor tiles in sizes of the 600mm x 600mm or more with water absorption less than 0.08% and conforming to IS : 15622, of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement : 4 coarse sand), including grouting thejoints with white cement and matching pigments etc., complete. as per DSR- 11.41.20

Providing & laying rectified glazed ceramic floor tiles of size 300x300 mm or more ( thickness to be specified by the manufacturer), of 1st quality confirming to IS:15622, of approved make, in colours white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 ( 1 cement: 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grounting the joints with white cement and matching pigmrnts etc., complete as per SI no. 11.39

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.110 mm diameter. As per SI- 12.41.2

P.C.C.(1 : 2 : 4) in fixing of Hold fast on Door , Window & Ventialtor

Provision for providing and laying of informatry sign board (Only for estimating purpose )

White Galzed Earthan Ware Full Basin Padestal S.I.No. 17 Chapter - 22

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreouschina flushing cistern & C.P. flush bend with fittings & C.I. brackets 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid D.S.R No- 17.3.1

Providing and fixing P V C WATER TANK 1000 LTS

Supply & Fixing Mirror Of Atul Make With Indian Polish Of 600X450mm Dia Size With Bevelled Edge.(S.O.R Chapter No . 22 S.N. 14)

Providing and fixing of 40 mm dia Semi Rigid PVC waste pipe for sink or wash basin including PVC. waste fittings complete. As per DSR-17.28.1.2

Providing and fixing 600 x 20 mm C.P. brass towel Road complete with brackets fixed to wooden cleats with CP brass screws as per DSR 17.73.2

Providing and fixing of 15 mm dia nominal bore G.I. pipes complete with G.I. fittings & clamps including cutting & making good the walls etc. exposed on wall. as per DSR - 18.10.1

Providing and fixing of 25 mm dia nominal bore G.I. pipes complete with G.I. fittings & clamps including cutting & making good the walls etc. exposed on wall. as per DSR - 18.10.3

Providing and fixing of CP brass 15mm dia nominal bore brass bib cock of approved quality conforming to Ch 21 S.NO 52

Providing and fixing of 15 mm dia nominal bore brass stop cock of approved quality as per Ch 21 S.No61

Providing and fixing of C.P. brass angle valve for basin mixer & geyser points of approved quality with 15 or 20 mm nominal bore as per Ch 21 S.NO 58

Providing and fixing of C.P. brass PILLARS COCK of approved quality with 15 or 20 mm nominal bore as per Ch 21 SNo 57

P/F ( INDIA MARKA HANDPUMP ) as per UPJAL NIGAM HARDOI

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, 2 way modular switch, modular plate, suitable Gi box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc, as required as per SI 1.11

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 * 2.5 sq. mm + 1 * 2.5 sq. mm earth wire as per SI 1.14.2

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required, 2 * 4 sq. mm + 1 * 4 sq. mm earth wire as per Sl 1,14.3

Wiring for circuit submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor. single core cable in surface/ recessed medium class PVC conduit as required. 4 X 10 sq. mm + 2 X 6 sq. mm earth wire as per SI 1.14.10

Add for Invertor wiring in wiring point for Light/Fan/Plug with 1.5 mm Cu Wire, as per SI UPPWD 189(A)

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections ellc, as required, as per SI 1.31

Supplying and fixing suitable size Gl box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc, as required, as per SI 1,32

Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect-CAT-AAA as per SI UPPWD-1413(A)

Suppily and fixing of recess Surface Pendent mounting round 6 Watt 8 Wall LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser! Reflector and driver set complete in all respect CAT-AAA as per SI UPPWD-1401

Supply and fixing of recess Surface Pendent mounting round 10 to 15 Watt LED Down Lighter having Powder coated die cast aluminium housing with heat sink, diffuser/Reflector and driver set complete in all respect CAT-AA as per SI UPPWD-1402

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos, blades, 30 cm long down rod, 2 nos, canopies, shackle kit, safety rope, copper winding. Power Factor not less than 0.9. Service Value (CM/MW) minimum 6.00 Air delivery minimum 210 Cum/Min, 350 RPM (tolerance as per IS 374 2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise 75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required, as per SI 19.1

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required. as per SI 1.25

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing. commissioning etc. as required. Upto 450 mm sweep as per SI 1.50.1

Please Enable Macros to View BoQ information