RE-TAPING AND REPAIRING OF CHARPOY GI PIPE WITH NYLON NEWAR, BED PLYWOOD TOP ETC AT BABINA CANTT UNDER GE BABINA

Amount

BED HARD (FD/E6/MAP/08(R)) : Welding to steel frames of Bed Hard including fixing of parts in proper position by preparing the old welding surfaces. Welding shall be done through gas welding, the thickness of the metal to be welded n. exc 18 gauge complete all as specified and as directed by Engineer-in-Charge.

BED HARD (FD/E6/MAP/08(R)) : S&F 12mm thick plywood BWR Grade IS-303 in single piece as per drawing without any joint to the bed frame with suitable screws wood/steel with cup washer including removal of damaged ply wood all as specified on drawing or as directed by Engineer-in-Charge.

BED HARD (FD/E6/MAP/08(R)) : S&F new stiffeners of size 25mmx25mm made of square MS pipe of 18 gauge to the frame of bed hard complete including removal of unserviceable stiffiners complete all as specified and as directed by Engineer-in-Charge and shown on drawing.

BED HARD (FD/E6/MAP/08(R)) : Supply and fixing 18mm thick one side teak face prelaminated particle board ISI marked to the frame of head rest in good finish after removing the old /broken board complete all as specified and as directed by Engineer-in-Charge and shown on drawing.

BED HARD (FD/E6/MAP/08(R)) : Supply and fixing 18mm thick one side teak face prelaminated particle board ISI marked to the frame of foot rest in good finish after removing the old /broken board complete all as specified and as directed by Engineer-in-Charge and shown on drawing.

BED HARD (FD/E6/MAP/08(R)) : M&L for painting to steel surfaces with two coats of synthetic enamel paint of black in colour over a coat of primer after preparation of steel surfaces. Note:-Primer shall be provided where welding has been done as well as on new MS square pipe surfaces as provided.

CHARPOY GI PIPE (FD-220) : M&L removing unserviceable nylone newar from charpoy GI Pipe and retaping with approved Nylone newar. The Nylone newar shall be of 50 to 55mm wide white/light colour 1st quality not made out from recycled nylon and weight of nylon newar shall be 1.5 Kgs of each charpoy. Weaving shall be done both sides by over lapping alternate bands to over the rails all round. Nos of bands shall be 32 to 34 (vertical) and 13 to 14 in horizontal, tightening complete charpoy i.e. loose checknuts , elbows, Long Rails and short Rails complete all as specified and shown on drg and as directed by Engr-in-Charge.

CHARPOY GI PIPE (FD-220) : Re-threading and fixing with elbow after removing and cutting the long rail wherever required all as shown on drg and as directed. Threading shall be done 22mm long at one end and 52mm long at other side and re-assembling of GI Charpoy as per drg and as directed by Engineer-in-Charge.

CHARPOY GI PIPE (FD-220) : Re-threading and fixing with elbow after removing and cutting the short rail wherever required all as shown on drg and as directed. Threading shall be done 22mm long at each side and re-assembling of GI Charpoy as per drg and as directed by Engineer-in-Charge.

CHARPOY GI PIPE (FD-220) : Re-threading and fixing with elbow after removing and cutting the leg wherever required all as shown on drg and as directed. Threading shall be done 22mm long at one end and re-assembling of GI Chorpoy as per drg and as directed by Engineer-in-Charge.

CHARPOY GI PIPE (FD-220) :- M&L for removing old unserviceable long rail from GI pipe Charpoy and supply and fixing new long rail of size 1884mm long made out of 32 mm bore medium grade GI Pipe duly threaded one side upto 22mm long at end and other side to 52mm long and re-assembling of GI charpoys after replacement of unserviceable long rail complete all as specified and as directed by Engineer-in-Charge. Note : - 1. The items includes threading both sides in new long rail also. 2. Old unserviceable long rail obtained shall be reused in Item No 12 below.

CHARPOY GI PIPE (FD-220) :- Converting long rail(retreved vide item No 11 here-in before) into short rail of size 804mm long and fixing complete to Charpoy GI pipe after threading 22mm long both end complete all as specified and as directed by Engr-in-Charge and as shown in drawing.

CHARPOY GI PIPE (FD-220) :- Converting short rail(retreved vide item No 12 here-in before) into leg and fixing complete to Charpoy GI pipe after threading 22mm long to Leg including 3mm thick MS sheet (made to shape of the bottom) in bottom as shown on drg by welding including removing old unserviceable leg complete all as specified and as directed by Engr-in-Charge and as shown in drawing.

CHARPOY GI PIPE (FD-220) : M&L for removing old unserviceable three way elbow and supply and fixing new elbow 32 mm bore,ISI marked weight not less than 350 gms & re-assembling of GI charpoys after replacement of broken elbow to charpoy GI Pipe, complete all as specified and as directed by Engineer-in-Charge.

CHARPOY GI PIPE (FD-220) : M&L for removing old unserviceable check nuts and supply and fixing new check nuts 32 mm bore 6mm thick to GI Charpoy, all as specified and as directed by Engineer-in-Charge.

CHARPOY GI PIPE (FD-220) : M & L for replacement of 3mm thick MS sheet by welding to bottom of GI legs as directed by Engr-in-Charge.

CHARPOY GI PIPE (FD-220) : M & L for replacement of broken MS clamps FI 25mmx3mm made to shape & welded with legs duly painted in black paint maching upto the existing as per shown on drg.

BED PLYWOOD TOP (1980mmx900mmx660mm (FD-246/ 247 ) : S&F 12mm thick plywood BWR Grade IS-303 in single piece as per drawing without any joint to the bed frame with suitable screws wood/steel with cup washer including removal of damaged ply wood all as specified on drawing or as directed by Engineer-in-charge.

BED PLYWOOD TOP (1980mmx900mmx660mm (FD-246/ 247 ) : S&F in repair new long rail 35mm x 90mm in section as per existing size of Bed of 1st class hard wood ( well seasoned teak wood ) including removal of damaged long rail all as specified on drawing or as directed by Engineer-in-charge. Note: Each long rail will be measured as single unit.

BED PLYWOOD TOP (1980mmx900mmx660mm (FD-246/ 247 ) : S&F new short rail 35mm x 90mm in section as per existing size of Bed of 1st class hard wood ( well seasoned teak wood ) including removal of damaged short rail all as specified on drawing or as directed by Engineer-in-charge. Note: Each short rail will be measured as single unit.

BED PLYWOOD TOP (1980mmx900mmx660mm (FD-246/ 247 ) : S&F head rest consisting of 60 x 30 x 260mm vertical size and 30 x 60 x 400mm horizontal including legs of size 60 x 60mm in section at top and length 400mm from bottom of leg and 30 x 30mm in section at bottom complete including removal of damaged head board all as specified on drawing or as directed by Engineer-in-charge.

BED PLYWOOD TOP (1980mmx900mmx660mm (FD-246/ 247 ) : All as per item No. 21 above but foot rest consisting of 22 x 75mm in section shisham battens 3 Nos at equal space, joining top and bottom horizontal rails of foot board. The top and bottom horizontal rails of size 30 x 60mm shall be 1st quality of shisham wood. The vertical legs above horizontal rails shall be 30 x 60mm all as specified on drawing or as directed by Engineer-in-charge. Note : Wood shall be Ist class hard wood (well seasoned teak wood).

BED PLYWOOD TOP (1980mmx900mmx660mm (FD-246/ 247 ) : S&F new stiffeners of size 40 x 60mm of Ist class hard wood (well seasoned teak wood) complete including removal of damaged stiffiners all as specified on drawing or as directed by Engineer-in-charge.

BED PLYWOOD TOP (1980mmx900mmx660mm (FD-246/ 247 ) : S&F 4mm thick plywood one side teak face of size 780 x 340mm outer and inner side including 12mm dia half cut teak wood beading of three side of head rest including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge.

BED PLYWOOD TOP (1980mmx900mmx660mm (FD-246/ 247 ) : S&F 4mm thick one side teak face plywood of size 780 x 180mm outer and inner side including 12mm dia half cut teak wood beading of three side of foot rest including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge.

BED PLYWOOD TOP (1980mmx900mmx660mm (FD-246/ 247 ) : S&F Flat iron size 150x35x5mm made to shape as per drg to be fixed with 6 nos of screw wood steel 35mm long ISI marked duly painted with Ist quality synthetic enamel paint black over a coat of wood primer of each corners of Bed plywood top all as specified on drawing or as directed by Engineer-in-charge.

BED PLYWOOD TOP (1980mmx900mmx660mm (FD-246/ 247 ) : Material and labour for preparation of old existing polished surfaces, new replaced parts of Bed plywood top by scrapping and rubbing down by emery paper including removing oily spots, ink dots, filling the cracks and pores with paste and putty and polishing with French polish as per IS code upto glossy finish to the entire satisfaction of Engr-in-charge. The tint of polish shall be exactly same as of existing polish colour of furniture or as approved by Engr-in-charge.

SOFA SET 4/ 5 PERSON WITH CUSHION (FD- 258, 281, 373 & FD/MAP-II/02) :Supply of foam cushion of size 558mm x 533mm x 100mm , 40 density duly covered all over with tapestry cloth superior quality not less than Rs. 350.00 per mtr as approved.A suitable chain with hook and runner of approved quality to one side of cushion shall be provided of required length as directed. Note :- (i) Each cushion for seat or back will be measured as single unit. (ii) Proof of rate i.e. purchase Vouchers must be submitted by the contractor

SOFA SET 4/ 5 PERSON WITH CUSHION (FD-281, 373 ) : M&L for Removing the existing unserviceable front leg from Sofa and providing new leg of size 70mm x 35 mm x 300mm of Ist class hard wood (Well seasoned wood) shisham wood rest all as shown on drg and as directed by Engr-in-Charge.

SOFA SET 4/ 5 PERSON WITH CUSHION (FD-281, 373 ) : M&L for removing the existing unserviceable rear leg from Sofa and providing new leg of size 70mm x 35 mm x 300mm Ist class hard wood (Well seasoned wood) rest all as shown on drg and as directed by Engr-in-Charge.

SOFA SET 4/ 5 PERSON WITH CUSHION (FD-281, 373 ) : M&L for Removing existing unserviceable Arm rest from Sofa and providing new Arm Rest of size 35mm x 70mm x 725mm Ist class hard wood (Well seasoned wood) rest all as shown on drg and as directed by Engr-in-Charge.

SOFA SET 4/ 5 PERSON WITH CUSHION (FD-281, 373 ) : M&L for Removing existing unserviceable side rail from Sofa and providing new side rail of size 35 mm x 100mm x 725mm Ist class hard wood (Well seasoned wood) rest all as shown on drg and as directed by Engr-in-Charge.

SOFA SET 4/ 5 PERSON WITH CUSHION (FD-281, 373 ) : M&L for Removing existing unserviceable bearer from Sofa and providing new bearer of size 40mm x 40mm x 725mm Ist class hard wood (Well seasoned wood) rest all as shown on drg and as directed by Engr-in-Charge.

SOFA SET 4/ 5 PERSON WITH CUSHION (FD-281, 373 ) : M&L for Removing existing unserviceable battens from Sofa and providing new battens of size 50mm x 20 mm Ist class hard wood (Well seasoned wood), rest all as shown on drg and as directed by Engr-in-Charge.

SOFA SET 4/ 5 PERSON WITH CUSHION (FD-281, 373 ) : M&L for Removing existing unserviceable front rail from Sofa three seater and providing new front rail of size 35mmx 100mm x 1590 mm sheesham wood rest all as shown on drg and as directed by Engr-in-Charge.

SOFA SET 4/ 5 PERSON WITH CUSHION (FD-281, 373 ) : M&L for Removing existing unserviceable front rail from Sofa single seater and providing new front rail of size 35mm x 10mm x 530 mm Ist class hard wood (Well seasoned wood) rest all as shown on drg and as directed by Engr-in-Charge.

SOFA SET 5 SEATER ( FD-258) : Supply and fixing arms made out of well seasoned teak wood free from cracks and knots, sapwood and other blemishes duly finished after removing the old /broken one as per drg and as directed by Engr-in-charge.

SOFA SET 5 SEATER ( FD-258) : Supply and fixing plywood commercial 12 mm thick BWR IS-303 grade in one piece after taking down the old /broken one and providing new ply suitable for seat of sofa 3 seater.Rest all as specified in drg and as directed by Engr-in-charge.

SOFA SET 5 SEATER ( FD-258) : Supply and fixing plywood commercial 12 mm thick BWR grade IS-303 as approved in one piece after taking down the old /broken one and providing new ply suitable for seat of sofa single seater. Rest all as specified in drg and as directed by Engr-in-charge.

SOFA SET 5 SEATER ( FD-258) : Supply and fixing back rail of sofa 3 seater made out of Ist class hard wood (well seasoned teak wood ) free from cracks and knots, sapwood and other blemishes duly finished after removing the old /broken back rail as per drg and as directed by Engr-in-charge.

SOFA SET 5 SEATER ( FD-258) : Supply and fixing back rail of sofa single seater made out of Ist class hard wood (well seasoned teak wood) free from cracks and knots, sapwood and other blemishes duly finished after removing the old /broken back rail as per drg and as directed by Engr-in-charge.

SOFA SET 5 SEATER ( FD-258): Supply and fixing front rail of sofa 3 seater made out of Ist class hard wood (well seasoned teak wood ) free from cracks and knots, sapwood and other blemishes duly finished after removing the old /broken front rail as per drg and as directed by Engr-in-charge.

SOFA SET 5 SEATER ( FD-258) : Supply and fixing front rail of single seater made out of Ist class hard wood ( well seasoned teak wood ) free from cracks and knots, sapwood and other blemishes duly finished after removing the old /broken front rail as per drg and as directed by Engr-in-charge.

SOFA SET 5 SEATER ( FD-258) : Supply and fixing foam cushion to back of sofa set of size 530x520x100mm , 40 density duly covered all over with tapestry cloth superior quality not less than Rs. 350.00 per mtr as approved over base of plywood commercial 9 mm thick in one piece shall be fixed to the back of the sofa set after removing the old one and as directed by Engr-in-charge and as per drg.

SOFA SET 4/ 5 PERSON WITH CUSHION (FD- 258, 281, 373 & FD/MAP-II/02) : Supply in replacement of cover for foam cushion size 558mm x 533mm x 100mm , made out of tapestry cloth superior quality not less than Rs. 280.00 per mtr as approved. A suitable chain with hook and runner of approved quality to one side of cover shall be provided of required length as directed.

SOFA SET 5 PERSON WITH CUSHION (FD- 258, 281, 373 & FD/MAP-II/02) : Material and labour for preparation of old existing polished surfaces, new replaced parts of Sofa set 5 Person by scrapping and rubbing down by emery paper including removing oily spots, ink dots , filling the cracks and pores with paste and putty and polishing with French polish as per IS code upto glossy finish to the entire satisfaction of Engr-in-charge. The tint of polish shall be exactly same as of existing polish colour of furniture or as approved by Engr-in-charge.

SOFA SET 4 PERSON WITH CUSHION (FD-281, 373, 258 & FD/MAP-II/02) : All same as per ser item No-46 above but Sofa set 4 person.

BUNKS (BED) MATTRESS AND DRAWERS (TP) :- Welding to steel frames of Bunks (Bed) mattress and drawers (TP) includes fixing of parts in proper position by preparing the old welding surfaces. Welding shall be done through gas welding, the thickness of the metal to be welded n. exc. 16 gauge. length of welding exc. 25mm at each point, all as directed.

BUNKS (BED) MATTRESS AND DRAWERS (TP) :- M&L for replacement of Unserviceable Foam Rexin and bottom ply of bunks (Beds) and supply and fixing new foam 50 mm thick 32 density covered with best quality Rexin including bottom plywood 12mm thick commercial MR Gde and to be fixed with screws to the steel frame as directed by Engr-in-Charge, size of ply 1840mmx760mm. Shape and size all as existing or as per directed by Engr-in-Charge.

BUNKS (BED) MATTRESS AND DRAWERS (TP) :- M&L for replacement of head rest duly made out of 18 / 19 mm thick prelaminated particle board exterior grade one side teak shade other side white in colour including first class hard wood Teak wood beading 6mm thick shall be provided all around complete of size 820mmx200mm.Shape and size all as existing or as per directed by Engr-in-Charge.

BUNKS (BED) MATTRESS AND DRAWERS (TP) :M&L for replacement of drawer duly made out of18 / 19 mm thick prelaminated particle board exterior grade one side teak shade other side white in colour including first class hard wood Teak wood beading 6mm thick shall be provided all around complete of size 700x400x120mm. Suitable brass handle and lock as approved shall be provided. Shape and size all as existing or as per directed by Engr-in-Charge.

BUNKS (BED) MATTRESS AND DRAWERS (TP) :M&L for replacement of leg duly made out of GI Pipe 32mm dia bore med grade of size 450mm long shape and size all as existing or as per directed by Engr-in-Charge.

BUNKS (BED) MATTRESS AND DRAWERS (TP) :- M&L for replacement of drawer of cabinet door duly made out of18 / 19 mm thick prelaminated particle board exterior grade one side teak shade other side white in colour including first class hard wood Teak wood beading 6mm thick shall be provided all around complete of size700mmx210mm. Suitable brass handle as approved shall be provided shape and size all as existing or as per directed by Engr-in-Charge.

BUNKS (BED) MATTRESS AND DRAWERS (TP) :Supply and fixing in replacement cabinate complete of size 790mmx750mmx420mm outer structure made of 0.80mm thick MS sheet and MS angle 20x20x3mm and complete with drawer and cabinate door made out of all same as per item ser no 51 and 53 above shape and size all as existing or as directed by Engr-in-Charge.

BUNKS (BED) MATTRESS AND DRAWERS (TP) :M&L for painting to steel surfaces complete with two coats of paint synthetic enamel black over a coat of primer after preparation of surface. Primer shall be provided where welding has been done as well as new conduit MS is provided.

M/S JAI BALAJI TRADERS

ROHIT ENTERPRISES