GE S U 18 2022 23 ADDN ALTN OF ROOFING FLOORING IN BLDG NO NP 64 SINGLE LIVING G TYPE T 288 OTHER ALLIED WORKS AND PROVN OF BATHING POINT NEAR BLDG NO NP 96 WATER PRESSURE PUMPS AT HQNC UNDER GE SOUTH UDHAMPUR

Amount

Dismantling Asbestos cement (corrugated or semi corrugated ) sheets as in roof covering complete all as specified and as directed.

Pre-painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and as directed.

Pre-painted galvatume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding, eves board and similar work to wall fixed with self tapping screws complete all as specified and as directed.

MS flat iron as in wind ties, gutter vally sun shades, chajja etc confirming to Fe 410-0 or Fe 310-0 including clamps complete all as specified and as directed.

Dismatling structural steel work including doors, gates etc complete all as specified and as directed.

Dismantling timber scantlings 40 Sqcm and over in section, in any position and in un-framed work complete all as specified and as directed.

Rolled section as in main and cross beams , purlins, rafters, posts where connected to common rafter and running rails,frame work of eves board, tank staging work etc conforming to Fe- 410-W complete all as specified and as directed.

S&F in repair 1.25 mm thick plain black mild steel sheeting in ridges hip , valley gutters drip and gutters and straight flashings ( Length and girth as fixed) complete all as specified and as directed.

Supply only integral water proofing compound complete all as specified and as directed.

PCC 1:2:4 using B-0 (using 12.50mm graded crushed stone aggregate) for coping, corner of roof and similar work etc including necessary form work complete all as specified and as directed.

Providing and injecting Along the external wall below concrete or masonry apron using Antitermite Treatment chemical emulsion @ 2.25 litres per running metre including drilling and plugging holes etc. in apron complete all as specified and as directed. Note : The treatment work shall be carried through authorised agency only, and certificate for the same for waranty shall have to be furnished before submitting payment)

Providing and injecting Antitermite Treatment of soil under existing floors using emulsion @ 1 litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand to match the existing floors complete all as specified and as directed. Note : The treatment work shall be carried through authorised agency only, and certificate for the same for waranty shall have to be furnished before submitting payment)

Providing and injecting Antitermite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and as directed. Note : The treatment work shall be carried through authorised agency only, and certificate for the same for warranty shall have to be furnished before submitting payment)

Demolition of cement concrete any description and any position not otherwise specifically provided complete all as specified and as directed.

75 mm thick PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) as in sub base of floor etc complete all as specified and as directed.

25 mm thick PCC 1:2:4 type B-0 (using 12.5mm graded crushed stone aggregates) as in level course on floor etc complete all as specified and as directed.

15 mm thick screed bed in cement mortar 1:6 for laying floor finishes complete all as specified and as directed.

Vitrified ceramic tiles(Double charged), area of each tile not exc 0.36 Sqm , 10mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

All as per srl item No 18 above but in vertical surfaces such as skirting/dado etc complete all as specified and as directed.

Non skid coloured tiles 7 to 8 mm thick area of each tile exceeding 0.11 Sqm but not exc 0.18 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and as directed.

Material and labour for 20-25 mm thick machine cut kota stone slab as in flooring, stair case and similar work over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

All as per Srl item No 21, above but in vertical surfaces such as skirting/dado etc complete all as specified and as directed.

20 mm thick makrana white marble slabs in narrow widths fixed with neat cement slurry as in floor including grinding and polishing mirror finish ( ganite polish) complete all as specified and as directed.

20 mm thick granite stone slab as in shelves / vertical surfaces /platforms set and jointed in neat cement slurry,pointed in colored cement to match the shade including rubbing of moulding etc complete all as specified and as directed.

Rounding to edges of stone slabs edge (Double moulding), such as in steps cooking platform and similar work all as specfied and directed cutting out old stone flooring, polishing with granite cutting and obtaining the mirror finish surface complete all as specified and as directed.

50 mm thick PCC type C-1, 1:3:6 (using 20mm graded crushed stone aggregates) as in plinth protection laid in alternate pannels finished even and smooth without using extra cement complete all as specified and as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and as directed.

Dismantling wall and ceiling boards (Fiber, pulp, insulation, blankets) any thickness including covered fillets and supporting members, frame, etc complete all as specified and as directed.

Providing false ceiling GI frame work for seamless ceiling comprising of GI perimerter channel 0.55 mm thick with two unequal flages of 20 to 30 mm and web of 27 mm fixed to surrounding wall using screws at 452 mm C/C channel 0.9 mm thick having two equal flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm c/c with GI cleat and steel expansion or sutable hanging from soffits\trusses\bracing supporting hanger compressing of GI wire complete all as specified and as directed.

4 mm thick 600mm x 600mm size asbestos cement plain E-boards designer ceiling fixed to GI grid work with screws and applying new surfaces two coat of distempers and one coat of primers complete all as specified and as directed. (Make:- Everest of equvalent)

Demolition of brickwork or stone / boulders masonry laid drybuilt in cement mortar complete all as specified and as directed.

Brick work with subclass B bricks, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed.

Taking down cement plaster and raking out joints, hacking for key, scrubbing down with water built in cement mortar any description complete all as specified and as directed.

Rendering 15mm thick in CM 1:4 on fair faces of brick/concrete finished even and smooth without using extra cement as in drain etc and similar work complete all as specified and as directed.

Rendering 10mm thick in CM 1:6 on fair faces of brick/concrete finished even and smooth without using extra cement complete all as specified and as directed.

Rendering 5 mm thick in CM 1:3 on ceiling,chajja,roof projection etc finished fair and even without using extra cement.

New plaster surface of walls and applying two coats of oil bound distemper over one coat of primer and two coat of wall care putty complete all as specified and as directed.

Preparation of new plastered or un-plastered surfaces and walls including cornices, pilasters etc and applying two Coats of cement base paint over a coat of primer complete all as specified and as directed.

Complete removal of existing treatment and applying two coats of oil bound distemper over a coat primer with two coats of wall care putty complete all as specified and as directed.

Complete removal of existing treatment applying two coat of cement base paint over a coat of primer paint on walls complete all as specified and as directed.

Complete removal of existing treatment applying three coat of white wash on walls surfaces complete all as specified and as directed.

Taking down frames with shutters (without taking off shutters from the frame ) area not exc 1.5 Sqm Each including iron mongry complete all as specified and as directed.

Taking down frames with shutters (without taking off shutters from the frame) area exc 1.5 Sqm but n.exc 4 Sqm Each including iron mongry complete all as specified and as directed.

Taking down shutter only exc 1.00 Sqm but n.exc 2.00 Sqm complete all as specified and as directed.

Solid PVC door frame superior colour of size 50mm x 47mm made out of 5mm thick plain color PVC sheet reinforced with with M.S square tube supplying and fixing in opening complete all as specified and as directed.

Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded palin colour PVC `C' channel heaving a PVC sheert strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bbottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site complete all as specified and as directed.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dove tailed or welded including one shop coat of red oxide primer complete all as specified and as directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

All as per Srl item No 47, aobve but wire gauge shutters complete all as specified and as directed.

Mild steel framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe-290, Gde-E-165 complete all as specified and as directed.

Preparation of new steel and iron surfaces exceeding 10 cms width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

105mm x 60mm pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer complete all as specified and as directed.

125mm x 60mm pressed steel frames for doors with one or more rebate including necessary fixing lugs, hinges lock strike plate etc complete as specified including a coat of shop coat zinc chrome primer complete all as specified.

30 mm thick flush shutter, solid core construction ,with block board core and plywood face panels ,commercial type complete all as specified and as directed.

Factory made 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc., sizes of members of shutters as specified in SSR Part I, supplied and fitted to chowkats complete all as specified and as directed.

Preparation of new wooden surfaces of any description ,not other wise described over 10 cm width or girth applying two coats of synthetic enamel paint over a coat of primers complete all as specified and as directed.

Mild steel cold rolled butt hinges medium weight 100 mm long complete all as specified and as directed. (ISI Marked )

200 mm long Aluminium anodised barrel tower bolt of extruded section complete all as specified and as directed.

150 mm length Aluminium handles fabricated type anodised complete all as specified and as directed.

300 mm long aluminium alloy anodised sliding door bolt with hasp staple (bolt type ) and fixing clips of sheets ,cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and as directed.

300 mm ordinary rat rail rod pattern spring including roller and roller plate complete all as specified and as directed.

3mm thick glass sheet oridinary quality in steel or wooden frames complete with fixing materials such as putty, glazing pins, wooden beads etc complete all as specified and as directed.

Galvanished mild steel wire cloth 0.56mm nominal dia of wire and average width of apperature 1.18mm complete all as specified and as directed.

Material & labour 2nd class hardwood plain, solid straight chowkhats and frames, wrought, framed rebated on the solid,rounded or chamfered, put together with glue pinned at joints, 2nd class HW complete all as specified and as directed.

S&F in repair 18/19mm thick block board, grade 2 quality, interior grade, commercial type fixed with screws to timber frame work/iron frame work (Termite treated / water proof) complete all as specified and as directed. (Make:Green Ply/Kit ply )

0.9 mm thick decorative choice of lamination type -1 of surface finish , colour and pattern as approved adhesive as per manufacturers instructions complete all as specified and as directed. (Make:Green Ply/Kit ply )

S&F in repair stain less steel catcher of superior quality complete all as specified and as directed.

S & F in repair 75mm size mild Steel butt hinges medium weight cold rolled complete all as specified and as directed.

S&F in repair 75mm long aluminium alloy handles, fabricated type, anodised (ISI Marked ) complete all as specified and as directed.

S & F in repair 30 mm width of flap Continous (Piano) hinges, mild steel, bright finish or electro galvanised complete all as specified and as directed.

S&F in repairs 20mm dia mild steel powder coated fancy type tubular curtain rail with brackets and end bulb as per requirement complete all as specified and as directed.

Disconnecting existing water tanks, setting aside (or lowering if required)for repairs, cleaning etc and hoisting if required reconnecting and refixing in postion etc exc 250 ltrs and nexc 500.00 ltrs complete all as specified and as directed.

Rotational moulded polyethylene water storage tank (cylinderical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I of capacity 1000 litres including all accessories complete all as specified and as directed.

20mm ball valve high pressure with polythylene float valve and fly nut complete screwed for iron pipe PTMT complete all as specified and as directed.

Gun metal globe or gate valve 20mm , with iron wheel head screwed both ends for iron pipe and loud in repairs complete all as specified and as directed.

S&F in repairs PVC connection 15mm dia and 45cm long with two Nos of brass checknuts and washers complete all as specified and as directed.

Dismantling of cast iron or reinforced concrete drain pipe 100 mm dia and below jointed in cement mortar and taking out of floor/walls etc complete all as specified and as directed.

110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and as directed.

110 mm PVC (SWR) bends any radius with access door complete all as specified and as directed.

110 mm PVC (SWR) branch piece, (single Y) equal or unequal with access door complete all as specified and as directed.

75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall complete all as specified and as directed.

75 mm PVC (SWR) bends any radius with access door complete all as specified and as directed.

75 mm PVC (SWR) T any radius with access door complete all as specified and as directed.

PVC (SWR) gully trap 125/110 mm, settting and jointing with solvent cement in repair complete all as specified and as directed.

110 mm PVC (SWR) vent cowl complete all as specified and as directed.

Preparation of old painted steel surfaces of any description ,over 10 cm in width or girth not otherswises described one coat of synthetic enamel paint complete all as specified and as directed.

Preparation of old wooden surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamal paint complete all as specified and as directed.

Excavating in trenches not exceeding 1.5m wide and n.exceeding 1.5m in depth for foundation etc and similar work and getting out in hard/dense soil complete all as specified and as directed.

Returning, filling in, icluding spreading, levelling, watering and well ramming in layers not exceeding 25 cm in hard/dense soil complete all as specified and as directed.

Removing excavated soil to a distance exc 50m and n.exc 1.50 km out side defence land complete all as specified and as directed.

Precast cement concrete type D-2 1:4:8 (using 40mm graded crushed stone aggregates) as in foundation, filling and mass concrete complete all as specified and as directed.

Reinforced cement concrete (nominal mix) 1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) as in footing, foundation beams, plinth beam, bases of columns etc complete all as specified and as directed.

Formwork to sides of concrete foundation, footing, bases of coloumn and similar work complete all as specified and as directed.

Mild TMT steel bar 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends, and including mild steel wire not less than 0.9mm dia or securing with clips quality conforming to TMT bars complete all as specified and as directed.

All as per Srl item 93, above but 6mm dia and over upto and including 8mm dia in stirrups, spacers and binders complete all as specified and as directed.

Roof trusses (framed) trussed, purlins, crane gantries rails and fastenings and heavy brackets, post and similar work framing (beam, tee, channel or flat sections) including distance pieces cleats including welding riveting etc complete all as specified and as directed.

Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment conform Fe 410 W (Gde-E-250 ) quality 'A' complete all as specified and as directed.

MS Steel screw bolts (machine made) with hexagonal or square heads at one and screwed at other or screwed both ends each scrwed and to be fitted with washer and one hexagonal or square nut, exc 16mm to 20mm dia of neck and n.exc 15cm long complete all as specified and as directed.

MS Steel screw bolts (machine made) with hexagonal or square heads at one and screwed at other or screwed both ends each scrwed and to be fitted with washer and one hexagonal or square nut, exc 12mm to 20mm dia and exc 15cm n exc 30cm long complete all as specified and as directed.

Brick work with sub class 'B' bricks straight or curved on plan exc 6m mean radius built in CM 1:4 as in drain, walls and similar work etc complete all as specified and as directed.

Rendering 15mm thick in CM 1:6 on fair faces of brick/concrete finished even and smooth without using extra cement complete all as specified and as directed.

Framed work such as doors, gates of angle or other section with gusset plates, rails, braces, etc complete drilled for fixing of steel sheeting or other covering doors, etc to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings including ornament and intricate design, including pintle hings, stops hand made sliding bolts etc conforming to Fe 290 Gde-E-165 complete all as specified and as directed.

Sand cushioning 20mm to 30 mm thick for laying and fixing interlocking tiles complete all as specified and as directed.

Machine pressed precast concrete interlocking paver block (glossy finish)of approved shape and size confirming to IS 15658-2006 of 80 mm thickness with grey cement and pigment, M-40 Grade of approved colour and design complete all as specified and as directed.

Machine pressed (factory made) precast plain cement concrete 1:2:4 type B-1(20mm graded crushed stone aggregate), kerb stone & the like of size 300mm x 300mm x 100mm thick or of size as approved by GE, with plain fair faces including chamfers, weathering etc, embedding in position/laid in trenches on edges of roads, including excavation in any type of soil, setting in cement mortar (1:4) returning filling and removal of surplus soil/debris to a distance n.exc. 50m from the starting point complete all as specified and as directed.

Plain cement concrete 1:2:4 type B-2 (using 40 mm graded crushed stone aggregates) as in channels and drains, foundation and similar work etc complete all as specified and as directed.

Walling of random rubble masonary, rectangular coursed, well bonded, bedded and solidly hearted, built in CM (1:6) complete all as specified and as directed.

Raised pointing to random or polygonal rubble, uncoursed on brought upto courses random rubble stone masonary in CM 1:3 complete all as specified and as directed.

Extra over stone walling for hammer dressing for lime sand stone n.exc 40 mm deep when held against straight edge complete all as specified and as directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms moulds, mitred/stopped ends etc complete all as specified and as directed.

Precast reinforced cement concrete (1:2:4) type B-1 (using 20mm graded crushed stone aggregates) for drain cover, manhole cover septic tank covers slabs etc including necessary form work and set in CM (1:4) complete all as specified and as directed. (Note:- Reinforcement will be measured and paid seperately.)

Mild steel TMT bars 6-8 mm dia and cut to length bent to shape required including cranking, bending, hooking ends and bending with MS wire not less than 0.9mm dia or securing with clips quality conforming complete all as specified and as directed.

Pre-cast RCC jallies 45 to 50 mm thick (measured solid ) including all mouldings but excluding frames conforming to type B-0 (using 12.5mm graded crushed stone aggregates) complete all as specified and as directed.

Raking out joints/ pointing Squared rubble masonry, coursed or uncoursed, random rubble or polygonal rubble uncoursed or brought up to courses complete all as specified and as directed.

Flush pointing to random rubble masonry, uncoursed or brought upto courses masonary in CM 1:3 complete all as specified and as directed.

Raised pointing to random or polygonal rubble, uncoursed on brought upto courses random rubble stone masonary in CM 1:4 complete all as specified and as directed.

Excavation in trenches n.exc. 1.5 m wide and n.exc. 1.5 m in depth for foundation or manholes etc, and area n.exc.10 Sqm on plan and getting out in any type soil complete all as specified and as directed.

Excavation over areas not exceeding 1.5 M deep and getting out in Soft/ Loose Soil complete all as specified and as directed.

SWG drain pipe grade 'A' of 150 mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified and as directed.

Concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in cement concrete type D-2 (1:4:8) for 150mm dia pipe complete all as specified and as directed.

Demolition cement concrete in ground floors and paving ( unreinforced ) nexc. 15 cm thickness ( below or above ground floor) complete all as specified and as directed.

PVC (SWR) junction single (single T) equal or unequal 110 mm dia with access door complete all as specified and as directed.

Machine pressed precast concrete interlocking paver block (glossy finish) any shape and size (sample approved by GE) confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and as directed.

Precast cement concrete ( factory made)1:2:4 type B-1 (using 20 mm graded crushed stone aggregates) set in cement mortar as in road kerbs and similar work etc complete all as specified and as directed.

Plain galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick in ridges, hips, valley gutters at the external end slope of any colour having tensile strength 550 Mpa as in roof(ridges) covering fixed with self tapping screws and caps etc complete all as specified and as directed.

Factory made, 2nd class hard wood 35 mm thick, plain framed, panelled shutters (two panels) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both sides. The size of rail and stile as per IS-1003 (Part-I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

Aluminium anodised barrel tower bolt of extruded section 150 mm long complete all as specified and as directed.

Steel locking bolt with mild steel electro galvanised plate and bright bolt not less than 10 mm dia 100 mm size complete all as specified and as directed.

18/19mm thick plywood, grade 1 (with BWR resistance/termite proof) with screws to timber frame work as in cup boards/Cabinets etc complete all as specified and as directed. Make : Century/kitply or equivalent.

12mm thick plywood, grade 1 (with BWR resistance/termite proof) with screws to timber frame work as in cup boards/cabinets etc complete all as specified and as directed. Make : Century/kitply or equivalent.

6.4 mm thick bevelled edge glass of area n exc 0.5 Sqm each as in shelves of size and shape as required at site complete all as specified and as directed.

Stainless steel clamps capable of supporting glass shelves of max width 200mm complete all as specified and as directed.

Dismantling of 1000 ltrs capacity water tank of any description including all connection and removing from site complete all as specified and as directed.

Ball valves 20 mm size high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for 20 mm bore pipe and fixed (Minimum weight 210 gms) complete all as specified and as directed.

Rolled mild steel work of angle iron as in frames of doors , Cup boards and any discription etc conforming to grade Fe 410-O or Fe 310-O complete all as specified and as directed.

100 mm thick PCC 1:3:6 type D-2 (using 20mm graded crushed stone aggregates) as in sub base of floor mass concrete or similar work complete all as specified and as directed.

Screed bed or bedding layers of 20 mm thick cement mortar 1:4 for laying floor finishes complete all as specified and as directed.

Machine cut kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing with 15 mm thick of CM (1:4) backing coat including taking down cement plaster complete all as specified and as directed.

Reinforced cement concrete 1:2:4 type B-1 , (using 20 mm graded crushed stone aggregates) as in slab supported on walls, beams and columns, in floors, roofs and shelves and the like complete all as specified and as directed.

Form work to soffits of suspended slabs such as roof slabs floor slabs and similar work n.exc 200mm thick finished rough complete all as specified and as directed.

Form work to edges of concrete flats, breaks, concrete railing n.exc 200mm wide finished rough complete all as specified and as directed.

Cutting chases in brick wall, pinning in ,making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landing, steps, cills, sunshades, shelves, lintels etc.;and cutting chases for concealed water tubing or concealed conduit wiring, etc. and making good, cutting not exceeding 10cm girth complete all as specified and as directed.

Taking up or down of 15 mm bore pipes steel tubing and connections complete all as specified and as directed.

GI pipe medium grade15 mm bore in wall and ceiling or laying in floors, including new fittings as required at site complete all as specified and as directed.

Taking up or down GI tubing of 20mm bore and connectios including cleaning for refixing or removal to store complete all as specified and as directed.

Steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 20mm bore including complete all as specified and as directed.

Supply & fixing for Sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mmx460mm fixed as in repair complete all as specified and as directed.

15 mm bore bib taps, long body with wall flange with arreator fency type chromium plated cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule fixed in repair complete all as specified and as directed.

10mm thick rendering on fair faces of brick / concrete surfaces in cement mortar 1:3 and finished even and fair for receiving tiles on vetical surface complete all as specified and as directed.

Material and labour glazed ceramic tiles of size 350 mm x 250 mm x 7 mm/450x350x7mm thick coloured tiles on vertical surfaces set and jointed in neat cement slurry and pointed in white cement mixed with colour pigments to match the existing surface complete all as specified and as directed.

Chequered cement concrete (glossy finish)tile 300 mm x 300 mm x 25 mm thick with grey cement and pigment set jointed and pointed in neat cement slurry in floor including 20 mm thick screed bed cement mortar 1:6 complete all as specified and as directed.

Brick work with sub class B bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 complete all as specified and as directed.

Form work to sides and soffits of floor roof beams, beam haunching, girders, bressummers, lintels, cantilevers, shelves including supports, over hangers etc also splays between floor and beam etc all as specified for rough finished surfaces of concrete flat complete all as specified and as directed.

Supply only liquid water proofing compound complete all as specified and as directed.

Hard core of guage n exc. 63 mm deposited spread and levelled in layers n.exc. 15 cm thick watered and rammed to a true surface complete all as specified and as directed.

Glazed ceramic coloured tiles of size 300mm x 450mm x 7 mm /300mm x 600mm x 7mm wall tiles set and jointed in neat cement and in white/coloured cement to match with the colour of tile etc including 10mm thick backing coat of plaster complete all as specified and as directed.

Banks, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required; hooks (stay), heavy, for large gates; hook and pintle hinges; large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wind ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 complete all as specified and as directed.

4 mm dia galvanised steel wire 150 mm x 100 mm mesh made up in to mattresses or cages etc complete all as specified and as directed.

40 mm dia PVC waste pipe for sink and wash hand basin of pressure rating 10 kgf/Sqm complete all as specified and as directed.

PVC (SWR) Floor trap, 75 mm dia of outlet, plain with grating including jointing with solvent cement and making good complete all as specified and as directed.

CP Bib taps cast copper alloy with crutch or butterfly handle two bay, screwed for iron pipe of dia 15mm, fancy type fixed complete all as specified and as directed.

CP angle valves cast copper alloy,fancy type with long shank and cup, bore 15mm, fixed complete all as specified and as directed.

125 mm dia brass chromium plated shower rose with swivel joints complete all as specified and as directed.

600 mm long tubular tower rail brass chromium plated 20mm dia, D type 60cm long fixed with two plugs (Gutties) of 2nd class hard wood embeded in cement mortar 1:3 with MS screws complete all as specified and as directed.

Supply, fixing and installation of 0.5 HP Water pressure pump of automatic ON and OFF operation, noiseless operation and low power consumption, Y type brass strainer (to avoid clogging) and float switch (for dry run protection) including electric connections i.e. switch, socket, point wiring etc complete all as specified and as directed. Make : Crompton CFMSMB3D0.50-V24 or equivalent make of Havells/Kirloskar

Supply, fixing and installation of 1.0HP Water pressure pump of automatic ON and OFF operation, noiseless operation and low power consumption, Y type brass strainer (to avoid clogging) and float switch (for dry run protection) including electric connections i.e. switch, socket, point wiring etc complete all as specified and as directed. Make : Crompton CFMSMB3D1.00-V24 or equivalent make of Havells/Kirloskar.

Taking down carefully, copper/ aluminum point wiring (light, fan, socket or power/ LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc and making good disturbed surfaces of walls floors and ceiling Keeping the LED lights in safe custody complete all as specified and as directed.

Point wiring for one light/ fan/bell point controlled by one switch using 1.5 Sq mm FRLS copper conductor cables (multistranded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5mm and 20mm dia), medium grade with Modular metal flush boxes thickness (1.25mm) & PVC back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts copper conductor cable 1.5Sq mm as earth wire stranded and conected to earth dolly complete all as specified and as directed. Make: Havells/ Finolex/ Polycab/ L&T

All as per srl item No 167 but for 3 pin 6 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 Sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per srl item No 167 but for 3 pin 6 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 Sq mm earth wire and connected to earth dolly complete all as specified and as directed.

All as per Srl item No 167 but for 3 Pin 16 Amps socket outlet independent with cable 2.5 Sq mm including copper PVC insulated PVC unsheathed 1.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

All as per Ser item No.167 here-in-before but for one 3 Pin 15 Amps socket outlet independent with cable 4.0 Sq mm including copper PVC insulated PVC unsheathed 2.5 sq mm earth wire standard and connected to earth dolly complete all as specified and as directed.

Switch flush type 6 Amps single pole one way (Modular Type) with outer strip complete all as specified and as directed.

Switch flush type 16 Amps single pole one way (Modular Type) with outer strip complete all as specified and as directed.

Socket 2-in-1, 3 Pin 6 Amps (Modular Type) with outer strip complete all as specified and as directed.

Socket 2-in-1, 3 Pin 6 & 16 Amps (Modular Type) with outer strip complete all as specified and as directed.

Electronic stepped type fan regulator 120 watt 230 volts 50 C/S deluxe modular type complete all as specified and as directed.

Ceiling rose surface bakelite 3 terminals complete all as specified and as directed.

Bell push 230 volts, AC complete all as specified and as directed.

Call bell ding-dong 230 volts complete all as specified and as directed.

S & F in replacement LED lights fitting 1x 20W, 230V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make : Havells/philips/Bajaj

S & F in replacement LED lights fitting 1x 10W, 230V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make : Havells/philips/Bajaj

S & F replacement LED light fitting 1 x 9W/1 x 10W bulk head luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

S & F in repairs LED wall mounting mirror type pitcture light fitting with high out put diffuser 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with flexible copper conductor cable of suitable size complete all as specified and as directed.

15 Watt Crown Shaped post top lantern in soothing opal finish made up of polycarbonate, suitable with 15 Watt E27 WW Ball Lamp Make : Havells or equivalent to Crompton/ Syska complete all as specified and as directed.

S & F in repairs LED building security light fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminum housing and heat resistant complete with driver, lamp, clamps,suitable bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

S & F in replacement MCCB triple Pole & Neutral capacity of 125 amps 415 volts rupturing capacity 16 KA complete all as specified and as directed. Make - Havells/ legrand/ Schneider

S&F in replacement Sheet metal enclosure double door type for MCCB TPN DB upto 125 Amps, 4 way vertical type 415 volts with 400 Amps rated busbar and neutral link including MCCB 125 Amps 16 KA , chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed. Make : Havells/Schneider/ Seimens.

S & F in replacement sheet metal enclosures for DBs when MCBs to be used double door DB SPN 08 way 240 volts with 200 amps rated bus bar and neutral link in cluding chases wall for dixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and as directed. Make :- Equivalent HPL/ Legrand/ Anchor

S & F in replacement MCB single pole 240 volt any rating from 10 to 40 amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and as directed. Make:- Havells/ legrand/ Schneider.

S & F in replacement MCB single pole and neutral 240 volt any rating from 63 Amps "C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and as directed. Make:- Havells/ legrand/ Schneider.

S&F in replacement single pole and neutral enclosure surface mounted 240 volts with 2 pin and earth plug and socket with one single pole MCB 25 Amps with indicator of complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 10 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 6 Sq mm as earth lead all as specified. including taking down old sub main wiring complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 06 Sqmm in PVC concealed conduit 25mm dia including PVC insulated copper conductor cable 04 Sq mm as earth lead all as specified. Including taking down old sub main wiring complete all as specified and as directed.

Earthing complete with galvanised steel earth plate electode 600mm x 600mm x 6.00mm thick burried directly in ground (earth pit not less than 2.25 meter deep below normal ground level connected to and including galvanised steel earth lead wire 4 mm dia by means of bolts, nuts, chock, nuts and washers of galvanised iron or steel including PCC Pit in 1:2:4 type B-I angle iron frame with RCC cover and handle, excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mash and light grade GI protection pipe 15mm bore upto main board complete all as shown in electrical plate No 3 of MES Sch 2009 (Part I) connected to main control board as specified and testing completion.

Taking down ceiling fan/Exhaust fans (of any size/make), cleaning its dust particles oiling,greasing,one coat of synthetic enamel white spray painting with blade ,reassemble the same along with all fittings and hanging the same back to its original position including connecting the wire to ceiling rose etc complete after completing the wiring complete all as specified and as directed. Note :- (i) The spares like condensor, ball bearing, cotter pin, nuts & bolts, connecting rods & hooks etc if found defective/damage deemed to be replaced and make the ceiling fans functional. No extra payments will be done on this account.

Switch piano 5 Amps single pole one way 230 V, 50 Hz, AC complete all as specified and as directed.

Switch piano 15 Amps single pole one way 230 V, 50 Hz, AC complete all as specified and as directed.

Socket outlet 2 in 1, 3 pin, 5A, 230 V, 50 Hz, AC complete all as specified and as directed.

Socket outlet 2 in 1, 3 pin, 15A, 230 V, 50 Hz, AC complete all as specified and as directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 4 Sqmm in PVC concealed conduit/casing capping 25mm dia including PVC insulated copper conductor cable 4 Sq mm as earth lead all as specified. Including taking down old sub main wiring complete all as specified and as directed.

Supply and fixing in replacement round shape 6 watt 220 volts AC surface type with high efficiency diffuser soft glare free light complete with drivers, holders,LED lamp suitable for roof ceiling including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed. Make- Havells/ Legrand/ Philips

S & F in replacement MCB Single pole and neutral 240 volt any rating from 40 amps"C" series, with rupturing capacity 10 KA ,inculding providing thimble for out going cable complete all as specified and as directed.

Supply and fixing in replacement LED building security light fitting 30 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp,clamps,suitable GI bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete all as specified and as directed.

Earthing complete with galvanized steel earth plate electrodes 600 mmx600 mm x6.3 mm thick buried directly in ground earth plate not less than 2.25 m deep below normal ground level with top edge of the plate not less than 1.5 m below normal ground level connected to and including galvanized steel earth lead wire 4.00 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron and steel including PCC pit in PCC 1:2:4 type B-1using 20 mm graded crushed stone aggregate, RCC frame with 40mm thick RCC cover reinforced with 8mm dia deformed bars handle including excavation and earth work in any type of soil medium grade GI watering pipe 20mm bore with funnel and wire mesh and light grade GI protection pipe 15mm bore main board complete all as shown in electrical plate No 5 connected to main control board all as specified and testing on completion. Note: Excavation earthwork charcoal PCC pit is covered under this item including taking out existing earth plate etc complete all as specified and as directed. Note: if earth resistance of earthing is not found (2 to 5 Ω) satisfactory if will be redone by the contractor on his risk and cost.

vijay constrction co

SINGH CONST CO

BHAGWATI TRADERS

VIRINDER SINGH