CA NO CWE/PAT/T-53/2020-21 SPECIAL REPAIR MD ACCN BLDG NO 236/1TO 4 FOUR QTRS AND T 259/9 TO 16 EIGHT QTRS AT MIL STN SANGRUR UNDER GE SOUTH PATIALA

Amount

Schedule 'A'Section-I (Building Works)

Total amount of Sch 'A' Sec I (Building Works)

Schedule 'A'Section-II (INTERNAL ELECTRIFICATION WORKS)

Total amount of Sch 'A' Sec III (Internal Electrification Works)

Schedule 'A'Section-III (Misc Items of Works) Note : This schedule is not pre-priced by MES and the pre-priced rate indicated as "Rs 0.00" under Col. 5 siginifies this fact only.

Preparation of new plastered surfaces/existing platered surfaces and applying acrylic wall care putty in internal/external walls/RCC surfaces/soffits of chajjas/roof projections/ cantilevers /balcony/ceilings etc (thickness vary from 1.5 to 2.5 mm as required for desired smoothness and levelling of surfaces in two or more layers) by using ready made wall care putty including sand papering after filling the putty to make surface smooth and ready for receiving interior/exterior painting complete all as specified and directed. Notes : (i) The prepared surface after wall putty, the contractor will inform to the GE as well as to the Engineer-in-Charge for site inspection before applying further external finishes. Please note that the further external finishes work will start only after approval of the prepared surface from the GE as well as to the Engineer-in-Charge through site order.

Preparation of surfaces and applying 02 coats of interior emulsion paint (light shade) @ 10 sq.m/litre/2 coats to wall surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.

Preparation of surfaces and applying 02 coats of interior emulsion paint (white shade) @ 10 sq.m/litre/2 coats to ceiling surfaces over & including a coat of interior wall primer @ 10 sq.m/litre/1 coat as recommended for under coat by manufacturer of interior emulsion by using following brands of emulsion and primer complete all as specified and directed.

Applying 02 coats of exterior emulsion paint (light shade) @ 5 sq.m/litre/2 coats by using roller to external walls/RCC surfaces/soffits of chajjas/roof projections/cantilevers/balcony etc surfaces over & including a coat of exterior wall primer @ 11 sq.m/litre/1 coat as recommended for under coat by manufacturer of exterior emulsion by using following brands of emulsion and primer complete all as specified and directed.

S&F factory made flush shutters 35mm thick, confoirming to IS : 2202 (part-I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneer on both faces of shutters compete all as specified and including supply and fixing following items : (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 Nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 Nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 Nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm - 1 Nos per leaf (e) Stainless Steel (304 Grade) Finished Floor Door Stooper - 1 Nos per leaf

S&F 35mm thick glazed and skelton shutters of 2nd class hard wood (factory made) open rebated and divided to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR-91 Pt-1 section 8 clause 8.20(a), kiln seasoned and chemically pressure treated all as specified including stainless steel 304 Grade wire cloth (wire dia. 0.22mm) and including painting with one coat of pink primer and two coats of synthetic enamel paint and the supply and fixing following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 4 nos per leaf (b) Stainless Steel (304 Grade) Finished Tower Bolt 200mm long - 2 nos per leaf (c) Stainless Steel (304 Grade) Finished Handles 200 mm - 2 nos per leaf (d) Stainless Steel (304 Grade) Finished Sliding Door Bolt/Aldrop 16x300mm - 1 nos per leaf (e) 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate - 1 nos per leaf

S&F powder coated 50 microns extruded aluminium glazing/ doors & shutters made out of section 63.5x38.10x1.29mm for chowkats or frame & shutters made of size 44.45x44.45x1.29mm for side rails and middle rail, 114.3X44.45X1.29mm for top rails and bottom rails and including 12mm thick PVC celuka Board wooden finish pre-laminated on one side and plain on other side below & above middle/lock rail and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beads 20mm size with and complete all as specified and directed including supply and fixing the following items: (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 3 nos per leaf. (b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

S&F powder coated aluminium glazing/ doors & shutters made out of aluminium anodised section 101.60x44.75x1.75mm for chowkats or frame & shutters made of size 85.00x44.45x1.29mm for side rails and middle rail, 114.3 x 44.45 x 1.29mm for top rails and bottom rails and including 12mm thick High Density Fibre Board pre-laminated on both sides (water proof) below middle/lock rail and 5mm thick tinted glass above the middle rail, and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including required nos. of pivots/hinges and brass mortice lock (four lever) and two Nos keys complete all as specified and directed by Engr-in-Charge including supply and fixing the following items: (a) Stainless Steel 304 Grade Finished Butt Hinges 150mm - 3 nos per leaf (b) Powder Coated Aluminium Tower Bolt 200mm long - 2 nos per leaf (c) Powder Coated Aluminium Handles 150 mm - 2 nos per leaf

Providing and fixing factory made extruded aluminium casement windows with 50 micron powder coating with provision for desert cooler, doubled panelled and double shutters consisting of frame and mullion of 101.60 X 44.45 X 1.29 mm and shutters made of 63.5 X 31.75 X 1.29mm and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and including 5mm thick glass in front shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperature in inner shutters complete fixed in all respect as specified including supply and fixing following items :- (a) Stainless Steel (304 Grade) Finished Butt Hinges 150mm - 2 Nos per leaf. (b) Powder Coated Aluminium Tower Bolt 150mm long - 2 Nos per leaf. (c) Powder Coated Aluminium Handles 150 mm - 1 Nos per leaf.

S&F factory made extruded aluminium ventilators with 50 micron powder coating of frame of 63.5 X 38.10 X 1.29 mm including 5mm thick frosted glass in lower 55% portion of shutters and stainless steel wire gauge 0.36mm dia and 1.40 aperture in upper 45% portion of shutter and to be fixed with and including EPDM gasket to render the glazing, air and water tight etc. & aluminium beeds 20mm size with and complete fixed in all respect as specified.

S&F factory made aluminium 50 micron powder coated grill, opening size 101.6 X 63.5 mm (4"X2½") and of approx weight @ 1.345 Kg/sq.m complete fixed in position in windows in all respect as specified.

M&L for single charge, vitrified, stainfree & scratch resistant, joint free, Premium (1st) quality straight edge coloured tiles 600 X 600 mm and 9-10 mm thick, as in floors etc. in any pattern as approved, set and jointed over & including 20mm th screed bed in CM 1:4 and pointed in white or coloured cement to match, in floors etc. and pointed in white cement with pigment to match the colour of tiles complete all as specified.

M&L for single charge, stainfree, vitrified tiles, Premium (1st) quality straight edge, coloured tiles 600 X 100 mm and 9-10 mm thick in any pattern of light coloured tiles as approved, on vertical surfaces such as skirtings, set & jointed in neat and pointed in white or coloured cement to match, as in skirting not 150mm high etc. in any pattern of light or dark tiles as approved to match the floor tiles, over & including 10 mm thick screed in cement mortar (1:4) complete all as specified and directed.

M&L for Premium (1st) quality digitally printed straight edge, punched, glazed ceramic rectangle tile in approved shade and finish in coloured tiles 600 X 300 mm and 8-9 mm thick, in any pattern of light & dark/highlighters tiles etc as approved, on vertical surfaces such as in skirting/dado etc, set and jointed in cement slurry over & including 10 mm thick rendering in cement mortar (1:4) and pointed in white cement with pigment to match the colour of tiles complete all as specified. Note : Dado should be flushed with the wall plastering.

M&L for Premium (1st) quality straight edge, ceramic tiles 300x300x7 to 8mm thick in floors etc in any shade and design/pattern of light and dark tiles etc as approved matching with wall tiles, set and jointed in neat cement slurry & pointed in matching coloured polymer cement based grout to match over & including 20mm thick screed bed in CM 1:4 complete all as specified.

M&L for anti-skid premium (1st) quality coloured tiles 400 X 400 mm and 7-8 mm thick, as in floors etc. in any pattern of light & dark tiles as approved, set and jointed in neat cement slurry and pointed in white or coloured cement to match, in floors etc. over & including 20 mm thick screed in cement mortar (1:4), over 25 mm thick cement concrete 1:2:4 type B-0 complete all as specified and directed by Engr-in-Charge.

M&L for Baroda Green marble, machine cut as in shelves/steps/cills/jambs/skirting/border only in tile flooring and the like works and flooring etc, 15-16 mm thick including bull-nose the front length, set and jointed in cement slurry over & including screed of 15 mm thick rendering in cement mortar (1:4) and pointed in cement mixed with pigment to match the shade of slab including rubbing, cutting and mirror type granite polishing complete all as specified. Note : Single piece should be used in steps/cills/jambs/shelves.

S&F cockroach trap gratings AISI-304 of size 150X150mm square in shape with 5mm border complete in all respect all as specified.

S&F vitreous china premium/1st quality wall hung wash basin white, flat back, size 500x400 mm including pedestal, screws & plug and brackets etc. all accessories as recommended by manufacturer incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and completein all respect as per manufacturer's instructions and taking down existing of any description/size all as specified.

S&F vitreous china premium/1st quality wash down water closet pan (pedestal pattern/EWC) S/P trap white colour of size 520x360x390mm including connection to drain (or out going pipe) and to flushing pipe, antisyphonagee pipe,etc.,with and incl. plastic seat cover as recommended by manufacturer closed pattern with flat bottom etc; and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified.

S&F flushing cistern of PVC 10 ltr. cap. with dual flushing system, valveless syphonic action type, , low level, white/ivory/off white with inlet, ball valve, float and including brackets and connection to pipe etc. and incl all necessary accessories like rag bolts/gel gasket etc as recommended by manufacturer for fixing, packing and taking down existing of any description/size complete in all respect all as specified.

S&F 6mm thick looking mirror fixed to wall with stainless steel plugs/connecter/spacers/screws etc. chrome finish with smooth finish edges/sides complete fixed in position all as specified and directed.

S&F overhead shower 120mm dia with 225-230mm long brass shower arm with wall flange and incl all necessary accessories as recommended by manufacturer for fixing complete in all respect all as specified.

S&F Bib taps, CP, fency type long body with wall flange screwed for 15mm bore of iron pipe or for brass ferrule and fixed in position complete in all respect all as specified.

S&F Concealed Stop Cock, fancy type, CP with long shank and cup, exposed part kit with wall flange, fitting sleeve, operating lever, adjustable wall flange and including regular brass body of concealed stop cock suitable for 15mm line with protection cap fixed in position complete in all respect all as specified.

S&F Angular Stop Cock, CP, fency type with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed ends for 15mm bore of iron pipe or for union and fixed in position complete in all respect all as specified.

S&F stainless steel tubing of 25 mm dia chromium plated min. 1.0 mm wall thickness as in curtain rod complete incl S&F 02 Nos stainless steel brackets/finials fency type, stops fixed with ss screws etc all as specified & directed as in repair . Note : For the purpose of mesurement and payment running length of curtain rod only shall be considered.

S&F PTMT Jet Spray with 1.5 metre long flexible tube including making connections and fixed in position complete in all respect as specified.

Complete removal of existing treatment of any type/description from walls/RCC surfaces etc with mechanical means/grinder complete all as specified and directed.

Providing and laying 3mm (-0.2/+0.3) thick APP with mineral finish (Atactic Polyproplene Polymer) modified prefabricated five layer, weight not less than 4.00 Kg/sq.m water proofing membrane mineral finished, reinforced with non-woven polyster matt make as approved including of a coat of bitumen primer @ 0.40 ltr/sq.m by the same membrane manufacturer of density 0.87 to 0.89 Kg/Ltr at 25 degree C temperature and viscosity 70 - 160 cps over the coat, 3mm th 5 layered APP membrane mineral finish shall be laid using butane torch and sealling all joints etc after the surface complete as per standard practice as per manufacturers instructions. The vital physical and chemical parameters of the membrane shall be as under - (i) Joint strength in longitueinal and transverse direction at 23 degree C as 650/450N/5cms (ii) Tear strength in longitudinal and transverse direction as 300 / 250 N/. Softening point of membrane not less than 150 degree C Cold flexibility upto 20 degree C when tested in accordance with ASTM (D05147) (iii) The laying of membrane shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed.

M&L for Built in cup boards with pressed steel frame of size 75x45x1.25mm thick and shutter of 1.00 mm thick MS sheet including spray painting 2 coats over a coat of red-oxide primer on steel shurfaces all around all shown on drawing No TD-178 sheet 2/3 to 3/3 dated 12 May 2001 (overall external size of cup board shutter incl frame shall be taken into consideration for the pupose of measurement) including One No hanging rod of CP steel 15/20mm bore with brackets & two Nos peg set of three pegs each fixed inside the shutter complete fixed in repairs i.e, incl taking down and removal of old unserviceable wooden or steel built-in-cupboards incl frame from site all as specified and directed by Engineer-incharge.

Chipping of unsound weak concrete / cover of reinforcement over slab, column and walls as per site requirement by chieseling maximum upto 30mm depth and removal of rubbish off the premises complete all as directed by Engineer in Charge.

Supply and apply of rust remover cum passivator by brush in two coat @ 0.3 kg/m2/coat of Density: 1.01 Kg/l at 300C complete all as per manufacturer's instructions and all as specified. Note : 1. The application of rust removal shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed. 2. Rates of scaffolding is deemed to be included in the rates quoted by the contractor against each item.

Supply and apply Cementitious Coating for Corrosion Protection having a cement based polymer modified rebar corrosion protection system by appling the first coat approx. 1mm thick layer of product carbonation resistance 2 mm of SikaTop Armatec®-108 or equivalent as specified corresponds to 20 mm of normal mortar; bond strength > 1N/mm2 according to ASTM C 882-78 applying @ 4 kg/m2 for two coats onto the prepared reinforcing steel with a medium- stiff brush. It is unavoidable that Sspecified product will also be applied onto the surrounding concrete. The second coat is applied in the same way after a waiting time of 2-3 hours (at +20°C) complete all as per manufacturer's instructions and all as specified. Note : 1. The application of Cementitious Coating for Corrosion Protection shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed. 2. Rates of scaffolding is deemed to be included in the rates quoted by the contractor against each item.

Providing, mixing & applying two component Epoxy resin concrete Bonding coat on prepared RCC surfaces as per manufacturer's specification including prepartaion of surface by chipping and throughly cleaning of surface complete whereever required and as per directions of Engineer-in-charge. Consumption: 0.5 kg/m2. complete all as per manufacturer's instructions and all as specified. Product requirements: Complies with ASTM C 881 Type II Grade 2 Class B+C. Note : 1. The application of Epoxy Bonding Primer shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed. 2. Rates of scaffolding is deemed to be included in the rates quoted by the contractor against each item.

Supply and apply a pre-batched one component polymer modified cementitious patch repair mortar in 25 mm thickness. Yield: approx. 0.84 ltr/kg. System requirements: compressive strength >= 50 N/mm2 (28 days) according to ASTM C 109; flexural strength >= 3N/ mm2 (7 days) according to ASTM C 293-79. Consumption of 2.1 Kg/Sqm/mm Note : The application of Polymer repair Mortar shall be got done through the authorised applicator of manufacturer of membrane only all as specified and directed. 2. Rates of scaffolding is deemed to be included in the rates quoted by the contractor against each item. Make : Sika / STP / Fosroc.

S&F 18 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC Celuka ply of both side plain white color fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed. Make : Rajshri Plastiwood / M/s Kumar Arch (P) Ltd or equivalent as approved by Accepting Officer.

S&F 18 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC Celuka ply of single side rigid laminate of approved colour and other side plain white colour fixed with screws, solvent cement/ adhesive to make kitchen/bed rooms cabinet sides top and bottom and shelves inside the cabinets complete as per manufacturer’s specifications complete all as specified and directed.

S&F 12 mm thick LEAD FREE PVC Celuka ply fixed with ss screws and solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed.

S&F 5 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC Celuka ply of single side rigid laminate of approved colour and other side plain white colour and pasted with solvent cement/ adhesive on frame work of cup boards complete as per manufacturer’s specifications complete all as specified and directed.

S&F 6 mm thick with minimum density 600 Kg/cu.m LEAD FREE PVC ply fixed with ss screws and solvent cement/ adhesive to make wall mount kitchen cabinet back and pull out drawer sides complete as per manufacturer’s specifications complete all as specified and directed.

S&F auto closing hinges 35 mm of 0 crank( KH-001) or 8 crank (KH-002) openable at 110 degree for kitchen cabinet shutters complete in all respect and fixed in position all as specified.

S&F Ball bearing runners 45 mm Telescopic (KTS-20) full extension load capacity 50 kgs complete all as specified..

S&F tower bolts 250mm long of stainless steel 304 finished/of outer plate metal matt finished complete all as specified and directed.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 200mm long matt finished complete fixed in position all as specified.

S&F Piano / continuous Hinge of size 19 mm stainless steel complete all as specified and directed.

S&F ball catchers 304 grade stainless steel finished suitable for cabinets premium quality complete fixed in position as per manufacturer's instructions all as specified.

S&F D-type cabinet handles premium quality, stainless steel 304/gloss chrome/SN finished 150mm long matt finished complete fixed in position all as specified.

S&F Stainless Steel 304 grade wire Basket (avg. wait 2.5 to 4 Kg. per basket) of pull out type like plain/cup&saucer/bottle/multi purpose/2-3 shelf baskets/Cutlery etc. for kitchens of required suze complete fixed in position all as specified.

S&F wardrobe tube/hanging rod for CB of size 30X15mm and 0.6mm thick stainless Steel 304 grade rectangular high gloss finish complete fixed in position incl S&F brackets/screws etc. all as per manufacturer's instructions all as specified.

S&F stainless steel finished locks (double action) with 2 nos of keys min outer body size 75mm suitable for wardrobes/CB etc. complete all as specified.

Taking down existing MS grills, etc.. Of any size/shape/section and re-fixing the same after repairing including any welding ( if required), hold fasts, embedded in PCC/RCC and complete removal of existing treatment, applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified.

Providing RCC cement concrete 1:2:4 type B-1 ( 20mm graded agg ) as in chajjas landing cover slab, shelves etc and set in cement Mortar 1 : 4, including form work and scafolding etc all as directed

Supply only chicken wire mesh 22 gauge of size not less than 20X20mm all as specified & as directed by Engineer-in-Charge.

Providing and fixing aluminium siliding windows with 50 micron powder coating, three track sliding windows with two glazed shutters, one 5mm th tinted glass ordinary quality and one shutter of stainless steel wire mesh 0.36mm dia wire and 1.40mm aperture including good quality of bearing handle, locks, including EPDM gasket to render the glazing, air and water tight etc complete all as specified and as directed.

S&F PTMT 450 mm long shelf for wash basin fixed in position complete in all respect all as specified.

S&F sheet glass shelf assembly consisting of 8mm thick sheet glass shelf of size 300X300mm as in corners with bevelled edges/hatching of edges fixed with SS 'D' bracket fixed and railing complete all as specified and directed.

S&F central hole brass chromium plated basin mixer with regular spout with/without popup waste system with 450 mm long braided hoses complete.

M&L for wall mounted mixer assembly, brass chromium plated, comprising of centre outlet tap, double inlets for hot & cold water, non telephonic shower arrangement, with connecting legs & wall flanges, inlets suitable for 15mm bore connections complete all as specified and directed.

S&F Sink Cock wall mounted with swinging spout and with wall flange, fency type chromium plated cast copper alloy screwed down, high pressure, screwed one ends for 15mm bore of iron pipe or for union and fixed in position complete all as specified and directed

S&F stainless steel sink with drainage board, AISI 304 quality grade, 1.00 mm thick, glossy finish, for kitchen with plugs washers and CP waste coupling of 32mm dia and including cantilever cast iron brackets, connecting union, etc, overall size 914mm x460/203mm (+ 10mm)with bowl size 405x 354 x 203mm( + 10mm) including waste pipe and making good disturbed portion in CM 1:3 or PCC 1:2:4 as directed.

Demolition of reinforced cement concrete of any description and in water storage tank of any size/capacity/description/position located on terrace of the building including moving the demolition portion to low lying area or out of defence land all as specified and directed.

Repair to RCC sunshades, Chajjas, Balconies, Columns, bands, beams and similar RCC work at any position/height by dismantling loose/disintegrated portion and dubbing out with Cement Concrete 1:1½:3, 15mm to 50mm thick using 6 to 12mm graded stone aggregate to make up and finished to required shape including provision of necessary supports if required and stitching of cracks with mild steel U clamps made out of 8mm dia @ 150mm c/c with inserting concrete block stretcher with cement mortar 1:3 mixed with adhesive chemical (Polymer based) and reinforced with PVC chicken mesh including form work where ever required and finished with10 mm thick plastering in CM 1:4 finished even and fair without using extra cement including preparation of surfaces to receive finishes complete all as specified and directed.

Applying three coats of brush bond acrylic based cementitious material of approved quality for sunken portion treatment all as per manufacturer instruction and providing 200 mm micron thick polythene film over 85/25 grade bitumen layer @ 0.5 kg /Sqm all as specified.

PVC(HDPE) SWR, 40 mm bore, single socketed in any length with rubber ring joints using solvent cement as per maunfacture instruction, incl reducer, socket, bends, TEE etc. and laid in walls/floor for connecting bottle traps complete all as specified.

S&F Cast iron soil waste and vent pipe,100mm bore, sand cast in any length, with or without ears, with lead joints, fixed to walls with and including stack clamps, nuts , bolts etc. and making necessary connections, fixed as in repair complete all as specified and directed.

S&F Cast iron soil waste and vent pipe,75mm bore, sand cast in any length, with or without ears, with lead joints, fixed to walls with and including stack clamps, nuts , bolts etc. and making necessary connections, fixed as in repair complete all as specified and directed.

S&F Cast iron soil waste and vent pipe,50mm bore, sand cast in any length, with or without ears, with lead joints, fixed to walls with and including stack clamps, nuts , bolts etc. and making necessary connections, fixed as in repair complete all as specified and directed.

Taking down of existing CI pipe 100mm bore and refixing the same after cleaning painting with 2 coats in any position complete all as specified.

S&F cast iron 4 way junction for 100 mm bore with access door as in repair complete all as specified.

Cast Iron (CI) gully traps, Centrifugal type 150 x 150mm size , square or roundmouthed, type 'P' or 'S' incl CI grating fixed in repair complete all as directed and specified.

M&L for Dummy joints/construction joints 8mmx10mm as in PCC floors filled with polyurethane elastic adhesive/sealant (white/grey colour) of aprrox density 1.3 kg/litre complete all as specified.

M&L Machine pressed rubber moulded precast cement concrete interlocking paver block any shape and size and of colour 50% red coloured tiles and 50% grey (ISI marked) coloured tiles confirming to IS-15658-2006 of 60mm thickness M-35 Grade and including filling of interstices with fine sand over including 25mm thick layer of sand chusion complete all as specified.

S&F Stainless Steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples including replacement of second class wooden beading where ever required in repairs complete all as specified and directed by Engineer in Charge.

S&F vitreous china premium/1st quality wash basin half pedestal, white, flat back, size 500x400 mm including pedestal, screws & plug and brackets etc. all accessories as recommended by manufacturer incl. CP bottle trap 32 mm with inlet and outlet screwed for pipe or connections incl all necessary accessories for fixing, packing, union and incl 32mm brass CP waste coupling and completein all respect as per manufacturer's instructions and taking down existing of any description/size all as specified.

Taking down carefully copper/aluminium sub main wiring complete, including existing batten/conduit on surface etc.,removing materials and making good disturbed surfaces due to taking down etc. to the entire satisfaction of Engineer-In-Charge, complete all as specified.

S&F in replacement tube light fittings, LED type retrofit T-8 20 Watt 4 feet long incl LED tube rod and incl 3 core flexible wire 0.5 Sqmm copper cable all as specified & directed,

S&F in replacement tube light fitting LED type 1x10 watt, 2 ft long including LED tube rod and incuding 3 core flexible wire 0.75 sqmm copper cable all as specified and directed.

S&F in replacement LED bulk head fittings 6 watt with IP 43 in engineering plastic housing with clear plastic diffuser and making connection with PVC insulated copper conductor 3 core cable of size 0.75 Sqmm complete all as specified and directed.

Taking down the KWH meter along with wooden board / DB after removing all electrical connection and Refixing, connecting the same or new serviceable KWH energy meter after wiring complete all as directed by Engineer in Charge.

M&L for Sheet metal enclosure factory made of size 20 cm x 25 cm x 12.5 cm deep box made out of 2 mm thick MS Sheet with double door with locking arrangement, epoxy powder coated holes drilled for cable entries suitable for accommodating electric energy meter including brick / cement work as per site requirement including flushing the box in wall and making good the disturbed portion of wall / surface complete all as specified and directed by Engineer in Charge.

Supply and laying in trenches through pipe under culvert or in air cable XLPE insulated PVC bedded galvanised steel strip or wire armoured, electric power cable (heavy duty) 1100 volts grade with stranded aluminium conductor of size 16 Sqmm 4 core complete all as specified and directed by Engineer in Charge.

Taking down unserviceable main switch DBs insulators, DB for MCB etc of any type and any capacity and further disposal including making good the disturbed surface and matching the colour of wall with the existing colour wash / paint / distemper where ever required (as per the existing) complete all as specified and directed by Engineer in Charge.

Taking down ceiling fan of any type and refixing on the location as directed after cleaning, oiling, overhauling, greasing, replacement of rubber bush, quarter pin etc. including connection with three core flexible PVC Conductor cable of size 23/0.776 complete

Taking down exhaust fan of any type and refixing on the location as directed after cleaning, oiling, overhauling, greasing, replacement of rubber bush, quarter pin etc. including connection with three core flexible PVC Conductor cable of size 23/0.776 complete

Taking down electric water heater of any size servicing and repair of geyser as required refixing the same and complete all necessary water supply connections replacement of hot and cold CP connections complete.

S&F blank speacer plate for single module complete all as specified and directed by Engineer in Charge.

Taking down old u/s main switch/DBs/MCB DB with MCB and making good disturbed surface complete all as specified and directed by Engineer in Charge.

S&F PVC Board 30 x 25 x 5 Cm depth for fixing of meter complete all as specified and directed.

S&F LED tube light Regal batten for LED type tube 1x22 watt,(Single side)complete all as specified and directed.

S&F LED tube light Photon ultra (1 x 20W Single side connection) complete all as specified and directed.

S&F LED Batton, 10 W Bright Light output of 1800 Lumens, Affordable batten with 100 Lm/W efficiency, Slim elegant design 35000 hours long life, LEDs 2 feet complete all as specified and directed by Engineer in Charge.

M&L for Lamp Holder, PVC/Polycarbonatetype with cord grip cap suitable for pendent / Angle type with provision of 1 x 10 W LED complete all as specified and directed by Engineer in Charge.

Taking down old unserviceable LT UG cable of any size from trenches/pipe/floor/walls complete all as specified and directed by Engineer in Charge.

S&F XLPE insulated, galvanised steel strip/wire armoured, heavy duty, LT cable with stranded aluminum conductor, 1100 volts grade,3.5 core 25 Sq.mm cross sectional area laying in trenches, passing through pipes, fixed along walls and/or poles complete all as specified.

Supply and fix in replacement of MCB SP 240 V, 6 to 32 Amps 'C' series, 10 KA complete all as specified and directed.

Supply and fix in replacement of MCB SPN 32 to Amps 240 volts complete all as specified and directed.

S&F MCCB 63 Amps 4 pole capacity 18 KA fixing in DB's complete all as specified.

Arneja Builders

VIKAS INFRASTRUCTURE