PROVN OF RETAINING WALL AT AHIRE OUTPOST ROAD AND CERTAIN MINOR WORK AT NDA KHADAKWASLA

Amount

Surface dressing not exc 15 cm deep in soft/loose soil.

Excavation in trenches n.exc 1.5m deep & n.exc1.5m wide on plan in soft/loose soil and getting out.

M&L for plain cement concrete (1:4:8) type D-2 (Using 40mm graded stone aggregate) as in foundation filling and mass concrete complete all as specified.

M&L for precast cement concrete block masonry with solid block, type C-1,(1:3:6) mix (Using 20mm graded stone aggregate ), exc 10cm in width and setting in cement mortar (1:6) complete all as specified and directed.

Returning filling in including spreading leveling, watering and well ramming in layers not exc 25 cm in soil.

Removing excavated material to a distance n.exc 50 m and depositing where directed at a level not exc 1.5 mtr above the starting point.

Spreading,levelling,watering and well ramming the earth filling under floor not exc. 25cm thick in layers.

M&L for hardcore of broken stone or boulders of gauge n.exc.63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface,complete all as specified and directed.

M&L for cement concrete tye D-2, (1:4:8) (Using 40 mm graded stone aggregate ) 75 mm thick as in sub base of floors complete all as directed. .

M&L for 25mm thick PCC (1:2:4) type B-0 (Using 12.5mm graded stone aggregate) as in flooring, finished fair and even without extra cement complete all as directed.

M&L for non skid coloured ceremic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specfied and directed.

M & L for rendering 10mm thick on brick wall or concrete surface in cement mortar (1:4) finished fair and even complete all as specified.

M&L for glazed ceremic tiles in vertical surfaces 300x200x7 mm thick, set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) complete all as specfied and directed.

M&L for applying three coat of white wash on newly plastered wall surface including preperation of the surface complete all as specified.

M&L for rendering 15mm thick on brick wall or concrete surface in cement mortar (1:6) finished fair and even complete all as specified.

M&L for applying two coats of cement based paint on new or undecorated wall surface including preparation of surfaces

S&F anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

M&L for sheet glass ordinary quality 3mm thick and glazing with oil putty in squares n.exc. 0 .5 sqm each pane complete all as specified.

S&F solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete or complete all as directed

S&F factory made solid PVC door shutter 30mm thick(style) consisting of frame made out of MS tubes for bottom and top rails. MS frame shall be covered heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail& bottom rail on either side & as gap insert for top rail & bottom rail; Panelling for plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, suppling and fixing in the frame at the site as per specification.

M&L for reinforced cement concrete (nominal mix) type B1, (1:2:4) (Using 20 mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span

M&L for reinforced cement concrete (nominal mix) type B1, (1:2:4) (Using 20 mm graded stone aggregate) in cover Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

S&F rolled mild steel in Roof trusses (framed), trussed,purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. - S & F - Fe 410 -W (Gde-E-250) quality-A

M&L for applying two coats of synthetic enamel paint over a coat of pink primer to wooden surfaces including preparation, exc 10 cm width or girth, complete all as specified.

S&F Pre painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified

S&F Pre painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified

M&L for 75mm thick PCC (1:3:6) type C-1 (Using 20mm graded stone aggregate) as in plinth protection finished even and smooth without using extra cement complete all as specified.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia.

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required,including binding with mild steel wire (annealed) not less than .9mm dia.

S&F 100 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed.

S&F 75 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed.

S&F125 mm long, aluminium, anodised, barrel tower bolts of extruded section all as directed.

S&F 125mm size aluminium handles,cast type,anodised all as directed.

S&F 250 mm long aluminium sliding door bolt with hasp staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding boltsof extruded sections all as specified and directed

Cutting chases, pinning in , for concealed water tubing on brick walls, making good to facing where required and pointing in cement mortar 1:3, not exc 10 cm girth.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing.

S&F 15 mm dia bib tap cast copper alloy (fency type), chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule complete all as directed.

S&F stop valve, cast copper alloy, fancy type,chromium plated with long shank and cup (Concealed type), screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe complete all as directed.

S&F15 mm dia brass chromium plated pillar tap, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut, capstan head, screwed for 15mm dia pipe complete all as directed.

S & F PVC connection 15x450mm size.

S&F 10 Ltrs (PVC) white, valve less, syphonic action type, dual type fluhsing cistern, low level with inlet ball valve, float and top push button type, complete all as directed.

S&F 32mm dia flush pipe of polythelene of low or high density, for low or high level flushingh cistern.

S&F 15mm bore Chromium Plated angle valve of approved make, screwed down for iron on both ends pipe.

S&F vitreous china,white, wash hand basin, flat back size 550x400mm 'including MS brackets including cutting for and pinning in, but excluding waste pipe.

Supply only 32mm dia waste pipe of polythelene,flexible, for wash hand basin or kitchen sink.

S&F 20mm dia brass chromium plated tubular towel rails, D type,60cm long between flanges,complete all as specified.

S&F vitreous china water closet (squatt pan) orrisa pattern 580x440 mm size pan white with front or back inlet with integral 'foot rests including provn of lime concrete bedding including connections to 'flushing cistern/pipe complete all as specified and directed.

M&L for PCC (1:4:8) type D-2 (Using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm dia SWG pipe complete all as specified & directed.

M&L for sail glazed stoneware drain pipes laid in trenches and jointed as specified - Internal diameter of pipe 150mm

S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 110 mm PVC (SWR), Junction single, (Single T) equal or unequal), fixed with solvent cement, with oval access door, complete all as specified and directed.

S&F 110 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 75 mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75 mm PVC(SWR) vent cowl complete all as specified and directed.

M&L for 75 mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 110 mm bore PVC (SWR) 'P' trap, including fixed with solvent cement complete all as specified and directed.

Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete (1:2:4) type B-1 smooth finished and reforming benching as required for 110 mm bore drain pipe.

M&L for RCC (1:2:4) type B1 (using 20mm graded stone aggregete) as in slabs supported on walls and the like

Form work to soffits of suspended slabs flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick, complete all as specified and directed.

M&L for 20 mm thick granite (of any type) work (table rubbed 7 polished ) in window door cills/jambs , platform like in 15 mm thick cement morter (1:6) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shed complete all as directed.

M&L for granite using 20 mm thick granite for partition/ vertical surfaces etc. in cement morter (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shed complete all as specified.

M&L for 20 mm to 25mm thick unpolished cuduppah stone slab as in below granite stone and vertical support and like incl necessary jointing and pointing and making good to disturbed surface complete all as specified

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations

M&L for gun metal gate or globe valve 20mm with iron wheel head ,screwed both ends for iron pipe

M&L for gun metal gate or globe valve 15mm with iron wheel head ,screwed both ends for iron pipe

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top three layered, ISI marked) hoisted and fixed in position all 1000 ltr capacity as specified in SSR Part I

Rough excavation not exceeding 1.5 m deep and getting out soft/ disintegrated rocks

Excavating over areas, n exc 1.5 m deep and getting out soft/ disintegrated rocks

M&L for walling of random rubble stone masonry uncoursed well bounded badded and solidly hearted built in CM (1:6) brought upto coursed.

M&L for pre cast cement concrete (1:3:6) type C1 (Using 20 mm graded aggregate) and setting in CM (1:6) concrete in joints to match as in bond stone.

Extra over stone walling for hammer dressing to face stone and dressing face beds and joints as specified of random rubble walling uncoursed or brought upto courses surface n exc 40 mm over granite or tral stone

M&L for raised pointing to random rubble masonry uncourded or brought upto courses in CM (1:4).

M&L for PCC (1:2:4) type B1 (Using 20 mm graded stone aggregate) as in coping and similar works incl necessary from work complete all as specified.

M&L for boulders filling of guage exc 80 to 150 mm hard packed tightly as in back filling of retaining wall.

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/ rolling and finishing to required size, shape, etc., n exc. 1.5 m high from base

Forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/ rolling and finishing to required size, shape, etc., exc. 1.5 m high/depth from base/top

M&L for 100 mm thick plain cement concrete type D2 (Using 40mm graded stone aggregate) (1:4:8) as in sub base or simillar works complete all as specified and directed

M&L for 100 mm thick plain cement concrete type B2 using 40mm graded stone aggregate (1:2:4) as in hard standing /path etc or simillar works complete all as specified and directed

M&L for finishing concrete surfaces by brooming

M&L for hand packing (Any thickness) of back of walls over arches etc & raising or lowering) to required level.

M & L for rendering 10mm thick in cement mortar (1:6) to the fair faces of brick work or concrete surfaces to be finished even and smooth without using extra cement all as specified and directed

S&F Reinforced concrete pipes, class NP2, laid and jointed complete with collars 600mm dia

M&L for PCC (1:3:6) type C2 (Using 20 mm graded stone aggregate) as in cement concrete in surface channels and drains

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mitred/stopped ends etc.

Dismantling fencing wiremesh/barbed wire any type

Dismantling posts or struts (steel or RCC) embedded in concrete, any section, including taking out embedded portion and making good the disturbed surface.

Excavation in post holes(or similar holes) each n. exc 0.5 Cum getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers n. exc exc 25 cm watering and removing surplus soil to a distance n exc 50 m and making good surface as in hard dense soil

M&L for cement concrete Type C-2, (1:3:6) (Using 40 mm graded stone aggregate) as in foundation, coping, filling and mass concrete all as specified and directed

Supply, fabricate and fixing in position angle iron posts for fencing posts and struts, split at bottom, cut to shape, including providing flat iron for securing wire mesh with necessary welding, drilling bolting or rivetting, complete all as spd and directed.(Steel confirming to Fe-290 (Gde E-165)).

Supply only of MS Galvanised chain link fencing, 3 mm nominal dia of wire, avg area of apperture 0.25 sqcm and/or weight of the fencing not less than 2.00 kg/sqm all as spd and diretced.

Fixing only MS galvanised chain link fencing, incl line wires any mesh, size and type to any type of standards, rails, straining bolts etc..incl provision of binding wire.

M&L for 10 mm dia MS round bars cut to length bent to shape required etc..(to be used for stiffness to chain link) fixed indepdently to the angle iron post as directed by Engr-In-Charge. (Conforming to Fe 410w (Gde E-250) quality 'A' or Fe 290 (Gde E-125).

S&F MS screw bolts (machine made 12 mm dia. Shank) with hexagonal or square heads at one end and screwed at another end, each screwed end to be fitted with washer and one hexagonal or square nut, exc. 5cm n. exc 10 cm in length.

S&F portions framed & hung as gates, including pintle hinges, stops, hand-made sliding bolts, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks & similar work conforming to Fe 290-0 Gde E-165

M&L for two coats of synthetic enamel paint over a coat of Red oxide primer including preparation of new steel/iron surface of any description over 10 cm in width or girth

Ditto all as above item 100 above but not exceeding 10 cm width or girth

Excavation in trenches n.exc 1.5m deep & n.exc1.5m wide and getting out in hard/dense soil.

M&L for precast cement concrete block masonry with solid block, type C-1,(1:3:6) mix (Using 20mm graded stone aggregate ), exc 10cm in width and setting in cement mortar (1:4) complete all as specified and directed.

Removing excavated soil exc 100 m but not exc 250 m and depositing where directed at a level not exc 1.5 mtr above the starting point.

M&L for point wiring in and including new concealed PVC conduit medium grade with the help of multi-stranded unsheathed FRLS copper cable 1.5 sqmm 650/1100V conforming IS : 3419 -1988 adhereing to colour code including earth wire of the size 1.5 Sqmm green colored FRLS grade with terminal boxes as required at site steel or cast iron as indicated and shall conform to IS 14772-2000 having top cover of laminated sheet 3 mm thick duly cut as per site requirement with cadmium plated steel screw and washers including making good the distrubed surfaces and matching it with existing surface for the following :- One light /fan point controlled by one switch one way

Ditto all as per item No. 105 above but one 3 pin 6 Amps socket out let point on same board.

Ditto all as per item No. 105 above but one 15 Amps socket outlet power point independent circuit with 4 sqmm copper conductor and 4 sqmm earth wire FRLS grade

S&F switch piano Conform IS 4615-1968 flush type 5 Amps single pole one way.

S&F socket outlet 3 pin 5A flush type complete all as specified. (Make:Anchor/Vinay)

S&F socket combination 5/15 Amps flush mounted 3/5 pin multi purpose all as specified. (Make:Anchor/Vinay)

S&F ceiling rose surface shall comply with IS:371-1979 Bakelite 60x 25 mm two to three terminals plates and of outside diameter not less than 63.5mm.

S&F LED tube light with diffused optics ultra bright LED 18/20 watt with high efficiency,integrated aluminum heat sink suited for installation in existing T8 tube light with G13 lamp holders complete all as specified. Make: Havells/Philips/Luker

S&F1x18/20W,230V surface and wall mounted T8 batten suitable for installing LED Tube including connecting up with twin core twisted flexible copper conductor cable from ceiling rose complete all as specified . Make: Havells/Philips/Luker

S&F 1x10 watt, 230 V surface and wall mounted T5 LED batten (for mirror) including connecting up with twin core twisted flexible copper cable from ceiling rose to fitting complete all as specified and directed Make: Havells/Philips/Luker

S&F LED building security light fiitting 20 W,IP-65 protection made up of die cast alluminium housing with high power LED as lighting source and lens complete fixing with bracket of adequate length made from GI pipe 25 mm, incl electrical connection from connector to light fitting. and fixed to wall with necessary MS clamp accessories complete all as specified and directed . Make:Havells/Philps/Luker

S&F MCB DB 04 way SPN double door sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar,surface mounting complete as reqd at site. Make:Legrand/Havells/C&S

S&F MCB SP 6 to 32 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing. Make: Legrand/L&T/Havells

S&F MCB SPN 40 Amps 240V,10 KA breaking capacity , C curve as per IS/IEC 60898-1 2002 with IP 20 protected terminals all as specified including complete connection with copper /aluminium cable lugs with suitable size for incoming and outgoing. Make: Legrand/Havells/L&T

S&F exhaust fan metal body of sweep 300 mm,single phase 230V with louvers and making hole as per the required size of the exhuast fan and making good the disturbed surfaces and fixing to the wall with proper fastner arrangements and all accessories.

M&L for earthing complete with galvanised steel earth plate electrode 600x600x6.3mm thick, burried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0 mm dia of minimum 15m length by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 in SSR PART-I connected to earthing test point all as specified or indicated including provision of earthing lead protection pipe, PCC earth pit with cover, excavation & earth work, testing on completion etc all as specified and directed.

M&L for laying XLPE underground cable 6 sqmm 4 core armoured sheathed with PVC cable stranded aluminium conductor 1100 volts grade complete all as directed.

M&L for laying of half round reinforced concrete pipe, of dia 150 mm, half round for bottom and half round for top and before laying excaved area shall be leveled. complete all specified and directed. Note : 01 Half round top and 01 half round bottom together will be considered as one running meter. Make as per sample given by Engineer-In-Charge

M&L for cutting of existing road/ hard standing by providing suitable T&P to make suitable size bore for fixing 50 mm dia pipe in road crossing etc. including the cost of making good the disturbed surface and matching with existing (Chequered tiles/Road/PCC) complete all as specified and directed

S&F GI tubing light grade 50 mm dia ISI marked with all fittings laid in trenches and fixed pole/wall by flat iron clamps, nut,bolt,washers suitable size all as specified and directed at size.

ELIEYAS TRADERS

Sayili Enterprises

SUN Enterprises

Sarkar Enterprises