ADDN ALTN CUM SPECIAL REPAIRS TO OFFRS, JCOS ORS MD ACCN IN 201 CEDU AT MILITARY STATION BARABANKI UNDER GE EAST LUCKNOW

Amount

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

M&L for non-skid coloured ceramic tile ( joint free tiles) 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exc 0.36 sqm in floors etc bedded over 15mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match and incl with motif/borders as in floors complete all as specified and directed.

M&L for non-skid coloured ceramic tile ( joint free tiles) 7 to 8 mm thick area of each tile exceeding 0.18 sqm but not exc 0.36 sqm in skirting/dado etc bedded over 10mm thick rendering in CM 1:4, set and jointed in neat cement slurry and pointed in white or coloured cement to match incl with motif/borders as in wall complete all as specified and directed.

M&L for glazed ceramic tiles coloured in vertical surface 300X450X7mm/300X600x7mm thick, including and over 10mm thick plaster in CM 1:4, set and jointed in neat cement slurry and pointed with white cement to match incl with motif/borders as in vertical surface, complete all as specified and directed.

M&L for coloured Non skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement clurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM (1:4) complete all as specified and directed.

M/L for 18 to 20mm thick Black granite ( of any type) work (table rubbed & polished) in steps, jambs, pillars, window-cills, cooking platforms & like laid over 15mm thick screed bed in cement mortar (1:4) including pointing into white cement (1:2) using marble dust with admixture of pigment to match shade of granite stone including polishing and making hole 25mm dia for gas pipe complete all as specified and directed.

S&F of PVC SWR nahani/floor trap plain grating including jointing with solvent cement 75mm dia

S&F for 100 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints, including all fittings like bend, T etc. laid in trenches or in floors upto Ist manhole confirming with IS:13592, Type-B, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and paving n.exc 15cm thick above or below ground level complete all as specified and directed.

Demolition of cement concrete (reinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Removing demolished material n exc. 500m and deposited where directed at a level n exc. 1.5m above the starting point complete all as specified and directed.

M&L for 75mm thick PCC 1:3:6 type C-2 using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified and directed.

M&L for 75mm thick PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in floor surface finished even and smooth without using extra cement complete all as specified and directed.

S&F /fabrication cupboard shelf/partition/frame/shutter made out of 18mm thick PVC board laminated sheet ,extremely impact perfect finish to the shutter and jointed together with solvent cement adhesive, 8mm thick (4mm x 2) x 12mm wide PVC sheet is used as gap insert for top & bottom rail, 18mmx1mm PVC edge lipping is done on top & bottom side using PVC solvent cement adhesive etc complete as per direction of Engr-in-Charge manufacture’s specification including dismantling of existing board (measurement shall be done of size of boarding in square) complete all as specified and directed. (Note :weight of PVC board of size 8' x4' should not be less than 36kg ) Make/Manufactruer:-Century Ply/Sintex/Surya Plast India/Rajshri Plastiwood

S & F for exterior chequred tiles of superior quality 300mmx300mmx25mm thick of approved design/shade set & jointed in neat cement slurry & pointed in white of coloured cement to match as in floor over and including 20mm thick screed bed in CM 1:4, completed all as specified and directed.

Surface excavtion n exc 30cm deep and avg 15cm deep and getting out soft/ loose soil complete all as specified and directed.

Hard core of gauge n exc 63mm ( using broken stone or boulder ), depoisted, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface.

M&L for 75mm thick PCC 1:4:8 Type D-2 ( using 40mm graded agg ) as in sub base of floor complete all as specified and directed.

M&L for sand laying under floors etc including watering and consolidation complete all as specified and directed.

M&L for 60mm thick pressed precast concrete interlocking paver block reflective type, rubber moulded coloured with white cement & pigment of M-35mm grade over 25 mm thick sand cushion as in floors complete all as specified and directed.(Note : sand cushion to be paid and measured seperately)

S&F machine made precast cement concrete kerb stone blocks of size and shape approved by Engineer-in-Charge using cement concrete 1:2:4 type B1 (20mm graded agg) complete all as specified and directed.

Cutting chases for brick walls pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc; and cutting chases for concealed water tubing or concealed conduit wiring, etc.and making good, cutting not exc 10 cm grith complete all as specified and as directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings (ISI Marked) and fixed complete to walls and ceilings or laid in floors including taking up or down steel water tubing and connections complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings (ISI Marked) and fixed complete to walls and ceilings or laid in floors including taking up or down steel water tubing and connections complete all as specified and directed.

M&L for refixing steel water tubing of 20mm bore with & including all new fittings (ISI Marked) and fixed complete to walls and ceilings or laid in floors including taking up or down steel water tubing and connections complete all as specified and directed.

S&F in repairs bib tap 15mm dia, chromium plated cast copper alloy with fancy type handle, screwed down, screwed for iron pipe or for brass ferrule all as specified.

S&F for 15mm bore dia pillar taps, cast copper alloy, with fancy type chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks & fly-nuts, screwed for iron pipes & fixed in repairs complete all as specified and directed.

S&F of stop/angle valves chromium plated, cast copper alloy with fancy type handles screwed down, screwed for iron pipe or for brass ferrule 15mm bore in repair complete all as specified and directed.

S&F 15mm bore stop valves, cast copper alloy, chromimum plated with fancy type handle with long shank & cup (concealed type), screwed down, high pressure, screwed both ends for iron pipe or for unions & fixed complete all as specified and directed.

S&F two -in-one bib tap 15mm dia, chromium plated cast copper alloy with fancy type handle, screwed down, screwed for iron pipe or for brass ferrule all as specified.

S&F 15mm bore CP central hole basin mixer popup waste system with 450mm long copper pipe and brass nuts.

S&F CP wall mixture 3 in-1 system includingr 1.50m long tele shower and overhead shower of size 150x150mm with W.F. ISI Marked Make Jaquar, Cat No 7281 or techocommercially equivalent of Cera/Hindware.

S&F health faucet with 1200mm long flexible mild steel tube with wall hook and chromium plated complete all as specified and as directed.

S & F for 150mm dia CP Swivel shower incl shower arm fixing with 15mm pipe complete all as specified.

S & F in repair 32mm bore brass chromium plated bottle trap for wash basins with inlet & outlet, screwed for pipe or connections including necessary packing union & cap & fixed

S&F chromoium plated box type toilet paper holder complete all as specified and directed.

S & F for CP grating 100mm dia complete all as complete all as specified and directed.

S & F for CP grating 125mmx125mm square with hole for waste pipe complete all as specified and directed.

S&F for aluminium anodised, tubular towel rail 'D' type 20mm dia 60cm long between flanges as in repair complete all as specified and directed.

S & F for glass shelves for looking mirror of size 450x125mm with chromium plated guard, fixed with brass screws and wooden/plastic cleats complete all as specified and directed.

S & F for PVC corner self of size 300 x 300mm complete all as specified and directed.

S & F for Corner Glass shelf 300mm with chromium plated guard, fixed with brass screws and wooden/plastic cleats complete all as specified and directed.

S&F for 10 Ltr capacity, PVC valveless, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

S&F in repair vitreous china squating pan of 'Orrissa pattern' long pan ofsize 580x440 mm white with integral foot rest excluding flushing cistern but including flush pipe and connection to drain (or out going pipe) and flushing pipe etc complete making good to floor complete all as specified and directed.

S&F in repair EWC vitrous china colour/white , P or S trap,incliding connection to drain or out going pipe and to flushing pipe with plastic water closet seat white, closed pattern , flat bottom and cover including MS CP hinges complete all as specified and as directed.

S&F in repair viterous china Wash Hand Basin white flat black type of size 550x400mm including cutting for and pinning in ends of brackets and fixing in walls complete all as specified and directed.

S&F PVC connection 15mm dia, with PTMT nuts of length 600mm complete all as specified and directed.

S&F chromoium plated soap dish best quaility complete all as specified and directed.

S & F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall and connecting union to pipe, overall size 915mm x 460 mm bowl size 410 mm x 330 mm x 160 mm complete all as specified and directed.

S&F in repair Kitchen Plate rack size 900 x 750x250 mm with average depth including necessary racking system and fixed in positon with rawal plug including taking down old fitment complete all as specified and directed.

S & F for 40mm bore PVC, waste down pipe for sink complete all as specified and directed.

Dismantling existing water tanks capacity exc 500 Ltrs but n.exc 1000 Ltrs, removing from site complete all as specified and directed.

S&F rotational moulded polyethylene water storage tank of capacity 1000 Litre, three layer construction, white colour, ISI mark (cylindrical vertical with closed top) hoisted and fixed in position with and including 20 mm dia GI pipe medium grade washout pipe 450 mm long with plug and 20 mm dia GI pipe medium grade overflow pipe 600 mm long with fittings including dismantling PVC water tanks and removing for capacity exceeding 500 litres & not exceeding 1000 litres etc. and removing from sitecomplete all as specified and as directed.

S&F ball brass valve high pressure with polythelene float and fly nut complete screwed for iron pipe or brass ferrule and fixed in repair of 20mm bore complete all as specified and directed.

S&F 20mm dia gun metal globe or gate valve with iron wheel head, screwed both ends for iron pipe and fixed of 15mm bore complete all as specified and directed.

Taking down of cement plaster in any description on brick or stone wall etc, incl racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M&L for rendering 10mm thick on fair faces of brick work or on concrete surfaces in CM 1:6 finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering, 05 mm thick in CM 1:4 and incl over 10 mm thick on otherthan fair faces of brick work or on concrete surfaces in CM 1:4 with water proofing compound as per manufecturer, finished even and smooth without using extra cement complete all as specified and directed. Note : WPC shell be measured and paid separately.

Supply only liquid water proofing compound.

M&L for rendering 05mm thick in CM 1:3 on ceiling and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for complete removal of existing treatment from old plastered surfaces of wall and applying two coats of oil bound distemper and one coat of primer on walls complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper and one coat of primer on walls , complete all as specified and directed.

Preparation of plastered or unplastered surface of ceiling including cornices etc. by brooming down, scrapping down smoke soot, moulds, moss and efflorescent salt and trading oil and greasy spots and applying two coats of white wash on old decorated surface of ceiling complete all as specified and directed.

Preparation of newly plastered surface of ceiling including cornices etc and applying three coats of white wash on surface of ceiling complete all as specified and directed.

M & L for complete removal of existing treatment from old decorated surfaces of wall including cornices etc and applying two coats of cement base paint (any colour as approved) complete all as specified and directed.

M & L for preparation the new plastered surface of wall including cornices etc and applying two coats of cement base paint (any colour as approved) complete all as specified and directed.

M & L for preparation of new or old plastered surfaces including complete removal of existing treatment and applying two coats of weather proof Exterior emulsion paint of APEX of BERGER or other equivalent brand and shade approved , over a coat of approved primer as recommended by the manufacturer on surfaces of walls complete all as required and as directed .

M & L for applying 3mm thick wall care putty on walls complete all as specified and directed.

Preparation of old painted surface of wood and wood based materials of any description over 10cm in width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

Preparation of old painted surface of steel or iron work of any description over 10cm in width or girth and applying two coat of synthetic enamel paint complete all as specified and directed.

Demolition mud in roofs, any thickness, including plastering and leeping (whether full thickness removed or only a part thereof) including cleaning washing down etc. complete all as specified and directed.

M & L for brushing neat cement slurry with 3 Kg of cement per Sqm complete all as specified and directed.

M & L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in padding to maintain slope complete all as specified and directed.

M & L for cleaning of all loose dirt and dust from roof surfaces and applying roof treatment as under :- (a) 10 mm thick plastering in CM (1:3) using 100 % coarse sand on roof / parapet walls with WPC @ 3 % by weight of cement. (b) Applying a coat of bitumenous primer confirming to IS-3384-1986 @ 0.40 ltrs/Sqm on prepared surfaces and allow to dry. (c) Supply and laying of 3mm thick (Minimum) polymeric water proofing membrane weighing not less than 3 Kgs/Sqm. (d) Applying two coat of bituminous aluminium paint, complete all as specified and directed. Note : (i) The net area of water proofing treatment shall be measured without any extra allowance for laps & portion inserted in groove which shall be deemed included in the quoted rates. (ii) Water proofing compound shall be measured and paid seperatly .

Dismantling of AC sheet (corrugated or semi corrugated) in roof covering all as specified and directed.

S&F for Pre-painted galvalume steel sheet 0.5mm thick of any colour approved by GE having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S & F for Pre-laminated galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified complete all as specified and directed.

S&F for mild steel work as in hold fasts, bracket, and other similar small articles complete all as specified and directed.

Taking down chowkhat or farme with shutter (without taking off shutter from the frame) area exc 1.5 Sqm but n.exc 4 Sqm each and removing from site all as specified.

Taking down chowkhat or farme with shutter (without taking off shutter from the frame) area not exc 1.50 Sqm each and removing from site all as specified.

Taking down door shutter of any description area n.exc 1.0 sqm each all as specified and directed

Taking down door shutters of any description area exc 1 sqm but n.exc 2 Sqm each and removing from site complete all as specified and directed.

Taking down door shutters of any description area exc 1 sqm but n.exc 2 Sqm each rescuring or easing & adjusting of shutter and refixing in same opening complete all as specified and directed.

Resecuring or easing & adjusting without taking down door shutters of any description area n.exc 1 Sqm each complete all as specified and directed.

S&F for mild steel work as in hold fasts, MS grating and other similar small articles complete all as specified and directed.

S&F 2nd class hard wood plain, solid, straight chowkhats and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S&F factory made 35mm thick 2nd class hard wood plain framed panelled shutter any number of panels with panels of timber flat on both side not less than 12mm thick complete all as specified and directed.

S&F 35mm thick factory made 2nd class hard wood glazed & skeleton shutters open rebated, prepared to receive glass, guaze etc. divided into square with plain chamfered or rounded, mitred and rebated sash bar any numbers sizes of members of shutters as specified in SSR Part-I section 8 of clause 8.23 (a) complete all as specified and directed.

S&F solid PVC door frame of size 50 x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube etc all as specified and directed.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisting frame made out of MS tube for top and bottom rail MS frame shall be covered with heat mould plain colour PVC C channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for style and plain colour PVC sheet for top rail lock and bottom rail on either side and as gap insert for top rail and bottom rail plain colour PVC sheet tape fixed in MS frame welding sealed to the style and rail with suitable PVC sheet bearing and jointing together with solvent cement etc complete all as specified and directed.

M&L for preparation of new surfaces of wood and applying two coat of synthetic enamel paint over a coat of pink primer on wooden surfaces over 10 cms width or girth complete all as specified and directed.

S&F for SS butt hinges medium weight 100mm size complete all as specified and directed.

S&F for SS butt hinges medium weight 75mm size, complete all as specified and directed.

S&F 300 mm long aluminium alloy, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding boltscomplete all as specified and directed.

S&F 150mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F 200 mm long aluminium anodized barrel tower bolt of extruded section complete all as specified and directed.

S&F 150 mm size alumium alloy handle, fabricated type extruded section complete all as specified and directed.

S&F 100mm size alumium alloy handle, fabricated type extruded section complete all as specified and directed.

S& F in repairs of 300mm long, ordinary rat tail rod pattern springs including roller & roller plate complete all as specified and directed.

S&F in repairs stainless steel wire cloth to steel shutters, 0.35 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, including taking out old rusted wire mesh complete all as specified and directed.

Supply and fixing only for stainless steel wire cloth 0.35 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from iron frames glazed with putty or wooden beads complete all as specified and directed.

S&F 4mm thick sheet glass ordinary quality & glazing with oil putty or wooden beads in square area n.exc 0.5 Sqm in each pane complete all as specified and directed.

S&F for 4mm thick pin headed sheet glass and glazing with oil putty in square n.exc 0.5 sqm in each pane

S&F for 19/20mm thick (BWP) block boards, grade 1 quality, exterior grade, decorative type with decorative face veneer on both faces fixed with screws to timber frame work as in cup board/ ward robe etc in repairs complete all as specified and directed.

S&F in repair kitchen cabinet shutter with frame including shelves made of solid UPVC foam profile with homogenous fine celluar structure having smooth outlet integral skin having 45mm width and 20mm thickness as vertical & horizontal stiles, joints are made and shall be fixed to walls using required size sheet metal screws and solvent adhesive vertical and horizontal profile made of UPVC profile frame of size 35mm x 17mm. The panel shall be filled with accucell polank profile of size 250mm width and 6mm thick complete all as specified by manufacturer's instruction and directed. Make/Manufactruer:- Fenesta/Winkraft/Yashpoly/Duraplast/Accura(Accucel)

Extra over solid PVC sheet for fixing 18mm width and thickness not less than 1mm, PVC coloured lipping of approved disign & colour fixed with solvent cement or headless nails complete all as specified and directed.Make/Manufactruer:- Fenesta/Winkraft/Yashpoly/Duraplast/Accura(Accucel)

S&F for clip type self closing hinges for cabinets fitted with cadmium coated screws all as specified and directed.

S&F 100 mm size bright finished chromium plated steel handle of approved shape & design fixed with cadmium coated screws on the kitchen cabinet shutters complete all as specified and directed.

S&F magnetic catcher for cabinets of size 50mm complete with striking plate & magnetic stud complete all as specified and directed.

S&F for 20 inches drawer runners folding type with guide channels & sliding channels with appropriate ball bearing/rollers etc complete to obtain smooth movement of drawers complete all as specified and directed.

Supply and fixing for stainless steel multipurpose basket of size 530x508x200mm for kitchen complete all as specified and directed.

Supply only for stainless steel Thali basket of size 530x508x200mm for kitchen complete all as specified and directed.

Supply only for stainless steel plain basket of size 530x508x100mm for kitchen complete all as specified and directed.

Supply only for stainless steel perforated cutlery basket of size 480x508x100mm for kitchen complete all as specified and directed.

Supply only for stainless steel grain trolly of size 480x508x320mm for kitchen complete all as specified and directed.

Supply and fixing stainless steel basket of size 20x20x12 inches (pull out 3 shelf) with side sliding roller clip over and including stainless steel channel on both side fixed complete all as specified as directed. Make: 3 Square /Godrej/Peacock/Sleek/Hettich

Supply and fixing stainless steel type basket of size 20x16x8 inches (pull out 3 shelf) with side sliding roller clip over and including stainless steel channel on both side fixed complete all as specified as directed. Make: 3 Square /Godrej/Peacock/Sleek/Hettich

Supply and fixing stainless steel type basket of size 20x16x6 inches (pull out 3 shelf) with side sliding roller clip over and including stainless steel channel on both side fixed complete all as specified as directed .Make: 3 Square /Godrej/Peacock/Sleek/Hettich

Supply and fixing stainless steel type basket of size 20x16x4 inches (pull out 3 shelf) with side sliding roller clip over and including stainless steel channel on both side fixed complete all as specified as directed make. Make: 3 Square /Godrej/Peacock/Sleek/Hettich

Supply and fixing stainless steel type basket of size 20x20x4 inches (pull out 3 shelf) with side sliding roller clip over and including stainless steel channel on both side fixed complete all as specified as directed make. Make: 3 Square /Godrej/Peacock/Sleek/Hettich

Supply and fixing stainless steel half circle type basket of size 28x20x4 inches over and including stainless steel pipe revolving type with with sliding rails complete all as specified as directed .Make: 3 Square /Godrej/Peacock/Sleek/Hettich

Supply and fixing in repair stainless steel wardrop trolly of any shape and size with side sliding roller clip over and including stainless steel channel on both side fixed size 33x20x8 inches with sliding rails complete all as specified as directed. Make: 3 Square /Godrej/Peacock/Sleek/Hettich

Cutting into existing manhole for connecting new drain making good to pipe & rendering, cutting out existing benching for forming branch channel 1/2 round in PCC 1:2:4 type B-1 smooth finished and reforming benching as required for 100mm dia pipe complete all as specified and directed.

Demolition and breaking up drain pipes 150 mm dia (PVC/SWG) set in cement mortar as in sewage line complete all as specified and directed by Engr-in-Charge.

S&F PVC (SWR) pipes of 110mm bore single socketed in any length with rubber ring joints, laid in trenchs or in floor complete all as specified and as directed.

S&F PVC (SWR) pipes of 110mm bore single socketed in any length with rubber ring joints, fixed with wall all as specified and directed

M&L for PCC 1:4:8 type D-2 using 40 mm graded aggregate for bed to drain pipes incl packing under and haunching against the sides of pipe (for 150mm bore after they are laid and tested complete all as specified and directed by Engr –in-charge

M&L for PCC 1:4:8 type D-2 using 40 mm graded aggregate for bed to drain pipes incl packing under and haunching against the sides of pipe (for 100mm bore after they are laid and tested complete all as specified and directed by Engr –in-charge

S & f MS pressed steel frames size 165x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc.complete all as specified and directed.

M&L for PCC (1:3:6) type C2 using 20mm graded stone aggregate filling of back side for MS frame at site all as specified and directed

Supply & fixing counter top wash hand basin of size 510x 410mm over black top granite and all necessary works etc complete all as specified and directed .Note Granite work shall measured and paid seperetaly

Supply and fixing SWR bends (any radius) 150/110mm complete all specified.

S&F 20MM dia for stainless steel curtain rods fancy type including fixing of two nos finials with 100mm long screws with properly fixed in wall all as specified and directed

S & F for stainless steel rail of 20 mm dia for wardrobe and incl fixing of two no aluminium brackets at both ends etc. complete all as specified and directed.

S&F bathroom mirror cabinet size 622mmx422mm (Make Prayag 555 or equivalent) complete all as specified and directed by Engr-in-chardge. MAKE: PRAYAG/COMMANDER

S&F in repair built up cubboards etc. frames and shutters fabricate and fixed with MS steel sheet and all fittings fixtures like hinges, knobs, hasp & staples, tower bolts, sliding bolts etc all locking arrangement of drawers and cubboards all painting and finishing work complete all as specified and directed .

S&F for mild steel framed work such as grills, gratings, etc., with ends of bar shoulder &/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water cooler & similar work conforming to Fe 290 Gde E-165 complete all as specified and directed .

M&L for preparation of new steel surface of any description over 10 cm width or girth and apply two coat of synthetic eenamel paint over a coat of red oxide primer complete all as specified and directed .

M&LReinforced Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates, water troughs and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work complete all as specified and directed .

Precast Reinforced Cement concrete Type B0 (Using 12.5 mm graded stone aggregate) in 50 mm thick Jallies or louvers including all mouldings complete and set in Cement Mortar 1:4 complete all as specified and directed .

Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, etc., and getting out in soft/ loose soil complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins, arches, pillars etc. complete all as specified and directed.

M&L for cement concrete type D-2 1:4:8 using 40 mm graded stone aggregate in foundation filling ,Sub-base and mass concrete filling complete all as specified and directed.

M&L for brick work with modular fly ash bricks, straight or curved on plan exc 6m mean radius in CM 1:6 complete all as specified and directed.

M&L for brick work with modular fly ash bricks, straight or curved on plan to any radius in half brick thick walls, built in CM 1:4 complete all as specified and directed.

M&L for precast RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in cover slab, shelves and similar articles set in CM 1:4 complete all as specified and directed. Note:- Reinforcement shell be measured & paid separately.

M&L for TMT bars 10mm dia and over cut to length, bent to shape required including cranking and binding with Mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per Item No 149 above but 6mm to 8mm dia ditto

All as per item No 149 above but 5mm dia and over upto and including 10 mm dia in stirrups, spacers and binders .

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in lintel up to 1.5m clear span, cills, steps, bands, coping including weathering, slightly rounded or champhered, angle and throating as directed and other similar work including necessary form work complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including form mould mitered or stopped ends complete all as specified and directed.

Supply and applying two coat of "sika rustoff 100" of sikka or techo-commercially equivalent other make/brand mentioned in make list as rust remover cum passivator by brush complete all as specified and directed as per manufacturer instruction. Note: Consumption of Product shall not be less than 02 kg /sqm/coat .

Supply and apply a cement based polymer modified rebar corrosion protection system using " sika top-armatec-108 plus " of Sikka (or techo-commercially equivalent other make/brand mentioned in make list ) complete all as specified and directed and as per manufacturer instruction .Note: Consumption of Product shall not be less than 0.80 kg /sqm/two coat .

Supply and applying Sika Monotop-122 F (or techo-commercially equivalent other make/brand mentioned in make list ), dual shrinkage compensated trowelable fiber reinforced, thixotropic high strength mortar for structural concrete repairs. The repair mortar should have a bulk density of ~1.3 kg/l at 27 ºc and should have compressive strength at an ambient temperature of +30°c according to astm c109 in 1 day ≥ 20 n/mm2 , in 7 days ≥ 35 n/mm2, in 28 days ≥ 50 n/mm2; flexural strength at an ambient temperature of +30°c according to en 196 -1 in 7 days ≥ 6 n/mm2 , in (28 days) ≥ 9 n/mm2; bond strength at an ambient temperature of + 30°c according to astm c882 in 7 days ≥ 8 n/mm2, in 28 days ≥ 12 n/mm2. Note : Consumption of the repair mortar should be as per manufactruer instruction.

M&L for Packer Drilling and fixing injection in Reinforced Concrete members as per following steps/procedure: (i) Drilling Holes: Drilling holes in structural members at the intervals as per recommendation of GE/Engineer-in-Charge. (ii) Cleaning of holes: Clean the holes by air blower prior to fixing nozzles. (iii) Fixing of Packers: Insert 12 mm dia., 50~75 mm long injection packers in cleaned holes with structural grade epoxy adhesive like Sikadur-31 or equivalent. (iv) Cutting of Packers: Cut the packers by cut of wheel after completion of grouting without damaging structural elements.

Supply and applying Sikadur-52 LP IN of Sikka (or techo-commercially equivalent other make/brand mentioned in make list ), a two part, solvent-free, low viscosity injection-liquid, based on high strength epoxy resin, according to specification. The epoxy injection system must have a mixed density of 1.1 kg/l at +27°C and the viscosity of ~250 mPas at +30°C. The epoxy injection should have following minimum physical properties: Compressive Strength according to ASTM C 579 at +30°C in 7 days should be ≥ 70 N/mm2; Tensile Strength should be ~ 50 N/mm2 after 7 days at +30°C according to ASTM D 638; Bond Strength to concrete according to ASTM C 882 should be ~7.5 N/mm2 after 2 days at +30°C & ~10.8 N/mm2 after 14 days at +30°C; Flexural strength according to ISO 178 at +30°C in 7 days should be ~50 N/mm2; Tensile Modulus should be ~2000 N/mm2 after 7 days at +30°C according to ASTM D 638; Tensile Elongation ~1.9 % according to ASTM D 638; Water absorption should be ~0.6 % after 24 hours water immersion according to ASTM D 570; Material should not shrink as per ASTM C 883.

Material and labour for point wiring with 1.5 Sq mm nominal cross sectional area, single core, 1100 Volt grade, multi-stranded, PVC insulated, unsheathed FRLS copper conductor cable with and including continuous earth wire of size 1.5 Sq mm nominal cross sectional area, single core, 1100 Volts grade, multi-stranded, PVC insulated, unsheathed, FRLS copper conductor cable and connected to common earth and earth dolly with suitable copper lugs and drawing into and including rigid non-metallic ISI PVC conduit of 20 mm dia or higher, medium grade complete with and including all PVC conduit accessories concealed into wall by cutting of chases in wall and replacement of sunk zinc coated pressed steel terminal box of 1.60 mm thick with 3mm thick plastic laminated sheet top cover , brass screws, cup washers etc and making good to the disturbed surfaces to match the existing complete all as specified and directed for one light / fan point controlled by one, one way switch 06 Amp including taking down carefully existing copper/aluminium point wiring such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc.

All as per serial item No 161 here-in-before but with suitable modular plate and top cover for modular point wiring instead of 3mm thick plastic laminated sheet top cover .

All as per serial item No 161 here-in-before but one bell/Buzzer point controlled by one push button on the same board with other switches or independent.

All as per serial item No 161 here-in-before but one 3 pin, 06 Amp socket outlet point on independent board controlled by one, one way switch 06 Amp.

All as per serial item No 161 here-in-before but one 3 pin, 06 Amp socket outlet point on same board controlled by one, one way switch 06 Amp.

All as per Serial Item No 161 here-in-before but point wiring with 2.5 Sq mm single core FRLS cables and earth continuity wire of 2.5 Sq mm single core FRLS cable for one 3 pin 16 Amp socket out let point controlled by one, one way switch on independent board complete all as specified and directed.

Supply and fix switch piano flush type, 06 Amp, single pole, one way, 230 Volt complete all as specified & directed.

Supply and fix bell push, 06 Amp, 230 Volt complete all as specified & directed.

Supply and fix socket outlet 2 in 1, 5 pin, 06 Amp, flush type, 230 volt complete all as specified & directed. Make : Havells - Reo or equivalent in Anchor - Penta PC / Legrand.

Supply and fix switch socket combination outlet 2 in 1, 3 pin, 06 Amp and 16 Amp flush type, universal, 230 volt, four hole complete all as specified & directed. Make : Havells - Reo or equivalent in Anchor - Penta PC / Legrand.

S&F switch Modular broad type 06 Amp 1 way single pole 230 V all as specified.

S&F switch Modular broad type 16 Amp 1 way single pole 230 V all as specified. Make: Anchor/SSK

S&F modular socket outlet 6 Amp 2/3 Pin 240 volt flush type all as specified.

S&F modular socket 2/3Pin ,6 & 16 Amp 2 module multipurpose all as specified.

S&F modular bell push single pole 1 module6 Amp, 240 volt all as specified. Make; Anchor/SSK

Supply and fix Bell ding dong type, AC, 230V, single pole complete all as specified & directed.

Supply and fix in replacement of industrial type SPN enclosure with a two pin and earth plug and socket complete with and including MCB, SP, AC, 240 volt of 20 Amp, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fix in replacement of industrial type SPN enclosure one way without bus bar complete with and including MCB, SP, AC, 240 volt of 10 Amp, 'C' curve 10 KA breaking capacity and flush to wall including all cuttings & chases etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

Supply and fix electronic ceiling fan regulator with rotary step, two module, humfree, AC, 240 volt, 100 Watt and duly ISI marked complete all as specified & directed.

S&F modular ceiling fan regulator electronic Stepped type for 1200/1400 mm sweep120W 2 module.

S& fixing RJ 11 telephone socket (Jack Type) with shutter 1 module all as specified. Make- Legrand/Anchor/Havells

S & Fixing TV co axial socket -1 module all as specified. Make- Legrand/Anchor/Havells

S & Fixing Metal flush box modular 1/2 module with modular white plate with frame allas specified forTV/Telephone socket

Supply and fix lamp holder, PVC / Polycarbonate type with back plate suitable for batten fitting including 10 Watt LED warm white bulb B22 CDL complete all as specified & directed.

Supply and fixing decorative LED lighting fixture with extruded aluminium, heat sink, environmental friendly, energy efficient ready to use suitable for 4' LED tube complete all as specified and directed. Make: Havells Cat Part NO REGALBATTENT8UPTO1X22WSSBSWH or techocommercially equivalent of makes mentioned in make list.

Supply and fix in replacement of single side connection LED T8 tube rod 20 Watt with PC body and diffuser, >2000 lumen, 6500K of four feet long into existing T8 conventional fluorescent tube light fitting after changing the necessary electric connections as required at site complete all as directed.

Supply and fix in replacement of LED mirror light fitting, 10 Watt, 2 feet long with IP 20 protection comprises of extruded aluminium housing, polycarbonate diffuser, integrated electronic driver with industrial grade heavy duty driver having THD < 10% all accessories pre-wired including connecting up complete all as directed. Make : Havells Cat Part No Endura Linear Neo or techocommercially equivalent of makes mentioned in make list.

Supply and fix in replacement of LED mirror light fitting, 12 Watt, 3000k warm white , projected type of dimension 500 x 180 x 95 comprises of metal and synthetic material, bronze colour including all aessories pre-wired including connecting up complete all as directed. Make : Philips Cat Part No Muziris, Model No 31403 or techocommercially equivalent of makes mentioned in make list.

Supply and fixing LED light fitting 1 x 11 Watt, 3000k warm white , B22, 230 Volt decorative wall mounting type with multicolour ABS housing with polycarbonate rings and glass shade with lamp holder, connector block, etc complete with all accessories prewired and including connecting up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and directed.Make Havells, Cat No. LHDL06160099 (CITY 3) or techocommercially equivalent of makes mentioned in make list.

Supply and fixing Brass made double light bracket with 130mm x 95 mm, decorative oval base, two brass arm 305mm, length, both tipped with decorative brass leaf and provided with 52mm length x 34 mm dia. galleries with flowers at top and with 2 pin brass holders inside, frosted glass shades 155mm x 129mm finish: black nickel plated, alongwith two 05W LED bulbs all as specified and directed by EIC. Make Mepro, Cat No. MBBD-900 or techocommercially equivalent of makes mentioned in make list.

Supply and fix in replacement of integrated LED bulk head fitting 12 Watt LED lamp, 60 lumen, 6500K with IP 66 and IK 09 impact resistance protection comprises of high pressure die cast aluminium housing, polycarbonate cover etc complete all as directed. techocommercially equivalent of makes mentioned in make list.

Supply and fix LED post top lantern fitting for 360 degree indirect light 35W IP 65 protection complete .

Supply and fix in replacement of LED security light fitting 36 watt, 3500 lumen, 5700K with IP 65 protection comprises of a pressure die cast aluminium housing, heat resistance toughened glass, LED lenses, surge protector, electronic driver, etc and all accessories pre-wired including connecting up with PVC insulated copper conductor cable 1.5 Sq mm, 3 core as required for connections and 32 mm bore light grade G. I. tube mounting bracket of 1.5 metre in length, bend to shape at 140 degree in ‘L’ shape and fixed to wall by means of 02 nos. of 40 x 5 mm flat iron clamps, nuts, bolts and washers etc complete all as directed. Make : Philips, Cat No : BRP409 LED CW 036 MR FG S1 PSU GR or techocommercially equivalent of makes mentioned in make list.

Supply and fix ceiling rose, 6 Amp, 250 volt, AC, ISI marked with three equal size terminals and PVC / Polycarbonate insulated body of 50 x 25 mm size complete all as specified & directed. Make : Havells, Cat No : AHEEIXW000 or equivalent in Anchor, Cat No : 39072 or SSK, Cat No 129/130.

Supply and fix in replacement of sheet metal enclosure distribution board, single pole and neutral, AC, 240 volt, 08 way, with 200 Amp rated copper bus bar and metal door with IP - 43 & IK 09 protection and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified & directed.

All as per serial item No 195 but 12 way.

Supply and fix in replacement of MCB, DP, AC, 240 volt of 32 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fix in replacement of MCB, SP, AC, 240 volt of 06 to 32 Amp capacity "C" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fix in replacement of MCB, SP, AC, 240 volt of 06 to 32 Amp capacity "B" curve, 10 KA breaking capacity and making connections by using suitable copper lugs complete all as specified & directed.

Supply and fixing of sheet metal enclosure distribution board triple pole and neutral (VTPN), AC, 440 volt, 04 way with 200 Amp rated copper bus bar and metal door with IP 54 and IK 09 protection alongwith cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified and directed and comprising of the following: (a) Incoming MCCB, 63 Amp, 04 pole, AC, 415 Volt of 16 KA breaking capacity complete - 01 No. (b) Outgoing MCB, SP, AC, 240 volt of 06 to 32 Amp, 'c' curve, 10 KA breaking capacity - 08 Nos.

Supply and fixing of sheet metal enclosure distribution board triple pole and neutral (VTPN), AC, 440 volt, 04 way with 200 Amp rated copper bus bar and metal door with IP 54 and IK 09 protection alongwith cable end box for above DB and flush to wall including all cutting etc in wall and making good to the disturbed surfaces to match the existing complete all as specified and directed and comprising of the following: (a) Incoming MCCB, 63 Amp, 04 pole, AC, 415 Volt of 16 KA breaking capacity complete - 01 No. (b) Outgoing MCB, DP, AC, 240 volt of 06 to 32 Amp, 'c' curve, 10 KA breaking capacity - 03 Nos.

M&L for replacement of sub main wiring with 2 x 10.0 Sqmm + 1 x 10.0 Sqmm earth wire , FRLS PVC insulated unsheathed flexible copper conductor (Multistrands), single core , 1100 Volts grade along with FRLS PVC insulated unsheathed flexible copper conductor (Multistrands) in green colour as continuous earth wire conforming to IS 694 with latest amendments and ISI marked, drawing in recessed/surface PVC conduct and making incoming / outgoing electric connections by using required size copper lugs / thimbles, making good to disturbed surface to match with existing including removal of existing old complete in all respect complete all as specified and directed. NOTE :- (i) Two run of single core FRLS PVC cable with one run of earth conductor and conduit shall be measured as one unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in CM (1:3) including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using PVC rawal plugs).

All as per serial item No 202 above but with 6.0 Sq mm nominal cross sectional area wire.

All as per serial item No 202 above but with 4.0 Sq mm nominal cross sectional area wire.

Taking down carefully electric meter by disconnecting all electric connection and kept at site and refixing the same after completion of wiring including suitable concealed MS box with BL sheet connecting of electric connection all as specified and directed by Engineer-in-charge.

Taking down carefully ceiling fan/ exhaust fan of any sweep complete with all accessories, dismantling blades and kept in safe custody including painting complete with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc and hanging and connecting up with provn of 3 core copper flexible cable of size 1.5 Sq mm from ceiling rose to fan complete all as specified & directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried vertically in ground (earth pit not less than 2.25 metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level steel earth plate connected with GI wire 04 mm dia by means of lug, bolts, nuts, check nuts, washers of galvanised iron or steel GI protection pipe 15 mm bore light grade all as shown in elect plate No 3 on serial page No 497 of SSR part I - 2009 and connecting to main switch board / Main DB’s including excavation, earth work, salt and charcoal dust mixed and packed 150 mm thick around GI earth plate, GI pipe medium grade 20 mm nominal bore watering pipe GI sheet funnel wire mesh, concrete pit, RCC cover 40 mm thick in PCC 1:2:4 type B1 duly reinforced with MS Bars 6 mm dia at the rate of 75 mm centre to centre both way with 12 mm dia lifting handle and pit / chamber in PCC 1:3:6 type C1, Angle iron 40 mm x 40 mm x 3 mm frame for pit cover including testing on completion complete all as specified and directed.

Supply and fix exhaust fans AC single phase 230/240 Volts of double ball bearing ,PVC body 300mm sweep ,bird guard and louvers complete all as directed.

Cutting walls of any type, making holes for fixing of exhaust fan any size or sweep and making good surface with fine plastering, finishing and colouring with existing colour matching complete all as specified and directed.

Supply & laying XLPE insulated, armoured, heavy duty, underground electric cable with aluminium conductor, 1100 volts grade, cross section area 25 Sqmm, 4 core, complete, all as specified and directed. (Note :- Excavation & Earth work shall be measured and paid separately under the respective items.)

Supply & laying XLPE insulated, armoured, heavy duty, underground electric cable with aluminium conductor, 1100 volts grade, cross section area 35 Sqmm, 4 core, complete, all as specified and directed. (Note :- Excavation & Earth work shall be measured and paid separately under the respective items.)

Supply & laying XLPE insulated, armoured, heavy duty, underground electric cable with aluminium conductor, 1100 volts grade, cross section area 10 Sqmm, 2 core, complete, all as specified and directed. (Note :- Excavation & Earth work shall be measured and paid separately under the respective items.)

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5m deep for laying of pipe, cable etc and getting out in soft/loose, complete, all as specified and directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers n. exc 25 cm thick in soft/loose soil, complete, all as specified and directed.

Removing surplus excavated material to a distance exc 250 meter and not exc 500 meter and depositing where directed at level not exc 1.5m above the starting point, complete, all as specified and directed.

M& L for sand cushioning in trenches for protection of under ground cable provided in layers of sand as 8 cm before laying the cable and 15 cm deep after laying cable complete all as specified and directed. Note : Punned thickness shall be measured and paid.

Supplying and laying un-reinforced precast concrete cable cover, class LV , type 1 with peak, size 250mm x 150mm x 40mm for protection of cable complete all as specified and directed.

Supplying and laying GI pipe, 40mm dia, Light grade for cable protection at road crossing etc including necessary road cutting and making good with PCC 1:2:4, Type B-1, using 20mm graded stone aggregate, 100mm thick or fixing on wall / poles of any type, secured with clamps complete all as specified and as directed .

M&L horizontal boring and inserting casing pipe along road and under pavements/ hard standing/ railway/ road /canals /streams crossing in all types of soil at prescribed depth (in no case the depth of boring be more than 0.9 m from the road surface for passing of LT cable including all civil works complete all as specified and directed. Note : if any damages to existing services such as OFC/gas pipe line/electric cable etc shall be repaired immediatelly by the contactor. Rate quoted above deemed to be included.

Supply and fixing electronic Energy meters temper proof LCD display with polycarbonate cover 3 phase 415 volts, 10-60 Amps, accuracy class-I 50hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH complete all as specified and as directed .

Supply and fix RCCB for earth leakage and short circuit protection 40 amps 4 pole 100 mA omplete all as specified and as directed .

Supply and fix LED warm white tube light fitting 18-22 watts four feet fitting omplete all as specified and as directed .

Supply and fixing USB charging point two module omplete all as specified and as directed Make: Anchor/Havells/Legrand.

Supply and fixing PVC conduit pipe 20 mm dia including all PVC conduit accessories concealed in to wall by cutting chasing in wall and making good the disturbed surface matching with the existing finshes omplete all as specified and as directed .

Supply and fixing indicator switch 2 module ,230 volts,50 hz complete all as specified and directed.

Supply and fixing indicator switch 230 volts,50 hz complete all as specified and directed

M&L for replacement of sub main wiring with 2 x 2.50 Sqmm + 1 x 2.50 Sqmm earth wire , FRLS PVC insulated unsheathed flexible copper conductor (Multistrands), single core , 1100 Volts grade along with FRLS PVC insulated unsheathed flexible copper conductor (Multistrands) in green colour as continuous earth wire conforming to IS 694 with latest amendments and ISI marked, drawing in recessed/surface PVC conduct and making incoming / outgoing electric connections by using required size copper lugs / thimbles, making good to disturbed surface to match with existing including removal of existing old complete in all respect complete all as specified and directed. NOTE :- (i) Two run of single core FRLS PVC cable with one run of earth conductor and conduit shall be measured as one unit. (ii) The quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in CM (1:3) including finishing the surface to match with the existing surface. The portion of sub main wiring at ceiling shall be in surface conduit of suitable size fixed on ceiling surface with using PVC rawl plugs).

Supply and fix exhaust fan AC single phase 230/240 volts of size 230 mm sweep, double ball bearing 900 RPM metal body sweep and louvers omplete all as specified and as directed .

M/s Reliable Electromech Systems

MD BUILDER

Ainisi Co.

SEAHAWK ENTERPRISES PVT LTD

Yadav Builders

sanjay enterprises