138WE/L-54/2020-21

Amount

Dismantling plain or corrugated steel sheeting any guage thickness including nanital or similar pattern complete all as specified and as directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling wall/floor and ceiling boards (fiber, pulp, inlsulation,etc) or insulation boards/slabs/blankets, any thickness including covered fillets complete all as specified and directed.

Dismantlng framed work in wooden fillets, rails, posts, rafters, purlins, grids for ceiling & wall panelling etc under 40 Sq.cm in secton, complete all as specified and directed.

Demolition of brickwork or stone / boulder masonary built in mud mortar including all quoins, arches, pillars etc, complete all as specified and as directed by the Engineer -in-Charge.

Demolition of precast concrete block walling built in cement mortar including all quoins, arches , pillars etc complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floor and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Demolition of cement concrete of any description and in any position not otherwise specifically provided for , complete all as specified and as directed by Engineer-In-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (But not backing ) and removing serviceable tiles to stone and rubbish of premises, complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc.laid bedded and pointed in any mortar, complete all as specified.

Taking down cement plaster / raised pointing on brick or concrete surfaces including racking out joints hacking for key, scrubbing down with water etc, complete all as specified and directed.

Taking down steel / PPR tubing ( 20mm bore) and connections in any position including cleaning for refixing or removal to store, complete all as specified.

Demolition and breaking up drain pipes ( salt glazedware, AC,Reinfoced concreet, PVC pipe) of internal dia upto100 mm bore, set in cement mortar and taking out of trenches if required, complete all as specified.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil, complete all as specified.

M&L for PCC (1:4:8), type D-2 (using 40mm graded crushed aggregate) as in mass concrete and filling of foundation , complete all as specified and as directed.

M&L for pre cast block masonry in cement concrete 1:3:6 type C-1 (using 20 mm aggregates) abd set in set in CM 1:6, complete all as specified and directed.

M&L Cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in lintels upto 1.5m clear span , cills, steps and other similar bands , plinth courses, parapets and railings upto 60 cm in height , coping , kneelers, spex stones, complete all as specified and as directed.

Hard core of broken stone or boulders of gauge not exc 63 mm deposited ,spread and leveled in layer not exc 15 cm thick complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded crushed stone aggregates) as in floor finishes, surface finished even and fair to receive top finish complete all as specified and directed.

75mm thick PCC 1:3:6 type C-2 (using 20 mm graded crushed stone aggregates) as in sub base complete all as specified and directed. .

35mm thick factory made 2nd class hardwood (Sal/Hollock) plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified

M&L for 15mm thick rendering on other than fair faces of brick works finished even and smooth (without using extra cement) in cement mortar 1:6 complete all as specified and as directed.

M&L for 15mm thick rendering on fair faces of brick works finished even and smooth (without using extra cement) in cement mortar 1:6 complete all as specified and as directed.

M&L for 10 mm thick rendering on fair faces of brick work as concrete surfaces finished even and smooth without using extra cement in cement mortar 1: 4 complete all as specified and as directed.

supply only Integral water proofing compound, complete all as specified and as directed.

Rolled mild sectins as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to Fe-290 Gde E-165 all as specified and directed.

S & F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to FE-410 - W(grade E-250) quality 'A', complete all as specified and as directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

Mild steel TMT bars 6 to 8mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips, complete all as specified and as directed.

RCC M-25, design mix, using 20mm graded crushed stone aggregateas in foundations, including rafts, footings foundation beams, plinth beams and like complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm (TMT) 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws, complete all as specified & directed.

Prelaminated particle board, 9mm thick, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with nails to timber frame work, fixed in wall panalling/ cupboard shutters and partition, complete all as specified and as directed.

Prelaminated particle board, 9mm thick, interior grade, prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with nails to timber frame work, in ceiling, complete all as specified and as directed.

Form work to sides of concrete foundation, footing, base of columns, and similar works for rough finished surface complete all as specified and directed.

Form work to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified.

S&F 0.63mm thick plain galvanised mild steel sheeting as in ridges hips, valley gutters drip and straight flashings (length and girth as fixed) with L or J hooks or coach screws with grade of zinc coating 275, complete all as specified and as directed.

S&F 0.63mm thick Galvanised corrugated mild steel sheeting with two corrugations side lap,fixed withcoach screws and washers in roofs walls etc. with grade of zine coating 275, complete all as specified and as directed.

Material and Labour for Mild steel work as in Hand rails, half round or other section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc.,and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed by the Engineer-in-Charge.

M & L for 50 mm PCC 1:3:6 type C-2 (using 20mm graded crushed stone aggregate) as in plinth protection, finished even and smooth with out using extra cement, complete all as specified and directed.

M&L Forming Contraction (Dummy) joints 50 mm deep x 10mm wide, filled with sealing compound Grade 'A' in plinth protection, complete all as specified and directed.

100 mm thick PCC 1:4:8 type B-2 (using 40 mm graded aggregates) as in sub base of floor complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 20-25 mm thick over cement screed bed 20mm thick in CM 1:6, set and jointed in neat cement slurry laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing, complete all as specified and directed.

M&L for Chequred cement concrete tiles 30cm X 30cm X 20mm thick, set ,pointed & jointed in neat cement slurry in floors polished with grey cement & pigments .Layed over 20mm thick cement screed base (1:6) ,complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (Square/rectangular) area of each tile exc 0.06 Sqm and not exc .11 Sqm in floor etc set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the tiles over and including screed bed with cement mortar (1:6) 15mm thick laying floor tiles complete all as specified and directed. Shade/Colour of tile shall be approved by the GE.

M&L for Glazed ceramic coloured tiles in vertical surfaces 350 x 250 x 7mm /450 x 350 x 7mm thick set and jointed in neat cement slurry and pointed with white or coloured cement mixed with pigments to match the colour of tiles over 10mm thick cement mortar (1:4) in dado/skirting tiles complete all as specified and directed. Shade/Colour of tile shall be approved by the GE.

Vetrified ceramic tiles 10mm thick (light shade) (square/rectangular), polished, area of each tile not exceeding 0.36 sqm as directed by EIC, as in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match the shade of tiles over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and directed. Shade/Colour of tile shall be approved by the GE.

Taking down chowkats / frames with shutters (without taking off shutters from the frames) area not exc 1.5 Sqm each complete all as directed by Engr-in-charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) area exceeding 1.5 Sqm and not exceeding 4 Sqm each complete all as directed by Engr-in-charge..

Taking down shutters of any description area exceeding 1 Sqm and not exceeding 2 Sqm each complete all as directed by Engr-in-charge.

Taking down shutters of any description area not exceeding 1.0 sqm complete all as directed by Engr-in-charge

Hacking old out broken glass (any thick ness, size, quality or description) from wooden panes or stone, concrete or brick surrounds, glazed with oil putty or fixed with beads, complete all as specified and as directed .

S&F 2nd class soft wood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

M&L for 2nd class soft wood clean sawn timber as in scatling fixed with nails, complete all as specified and as directed.

S&F mild steel work as in hold fasts and similar work confirming to Fe-290 or Gd -E 165, complete all as specified and directed.

M&L for treating wooden chowkats surface of any description n exc 10 cm in width or girth with black bituminus paint in two coats, complete all as specified and directed.

M&L for preparing surfaces and treating small articles of buliders hardware such as MS hold fasts , MS butt hinges etc, with two coats of synthetic enamal paint over a coat of primer when un connected with other painting or when painted in a defferent tint , complete all as specified and directed.

Material & labour PCC 1:3:6 type C-1, (using 20 mm graded crushed stone aggregate) as in hold fast , bed block and like, complete all as specified and as directed by the Engr-in-Charge.

35mm thick factory made 2nd class soft wood plain, framed, panelled shutters (two panels) with lock rail and panels of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial face veneers on both sides.The size of rail and style as per IS–1003 (Part-I), kiln seasoned and chemically pressure treated, fitted to chowkats, complete all as specified.

S&F for 40 mm thick Flush shutters, solid core construction ,with block board core and plywood face panels commercial type on both sides , Supply and fixed to chowkats , complete all as directed by Engr-in-charge.

S&F 35 mm soft wood Glazed and skelton shutter, open and prapared to receive the glass, gauze etc.(without sash bars) edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. (Glass / Wiremesh should be measured seperately) complete all as specified and as directed by the Engr-in-Charge..

S&F MS framed work such as grills, gratings etc with ends of bars shouldered and/or rivited or forged in spikes, framed guard bars, barred iron doors, ledders framed balsters walk ways railings frame work of water tanks and similar work confirming to Fe-290, Gde-E-165, complete all as specified and as directed.

M&L sheet glass 3mm thick ordinalry quality and glazing with oil putty or wooden beads in square not exc 0.50 sqm in each pane, complete all as specified and as directed.

S&FGalvanised mild steel wire cloth ,0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or galvanised wire staples, complete all as specified and as directed.

S&F mild steel butt hinges, medium weight cold rolled 100mm size, complete all as specified and as directed.

S&F 150mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and as directed.

S&F mild steel butt hinges, medium weight cold rolled 75mm size, complete all as specified and as directed.

S&F 100mm long aluminium anodized, barrel tower bolt of extruded section, complete all as specified and as directed.

S&F 100mm size extruded aluminium alloy handles, fabricated type, anodized, complete all as specified and as directed.

S&F in repair 300mm long mild steel ordinary rat tail rod pattern springs including roller and roller plate, complete all as specified and as directed.

S&F in repair 250mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed, complete all as specified and as directed

S&F in repair 300mm long aluminium alloy, anodized, sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolt and sliding bolts of extruded section or cast aluminium alloy fixed, complete all as specified and as directed

M&L for 2nd class soft wood clean sawn as in battens for grids of ceiling & lining fixed with nails exc 13 sqcm and n exc 25 sqcm in section,complete all as specified and as directed.

M&L for 2nd class soft wood clean sawn as in beeding for edges of Ceiling ,lining ,or wooden flooring work fixed with nails exc 6 sqcm and n exc 13 sqcm in section,complete all as specified and as directed.

M&L for 6mm thick (5 ply) plywood grade BWR type BB as in walling panelling fixed with nails to timber frame work, complete all as specified and as directed.

All as per description of item No 75.00 above but on ceiling, complete all as specified and as directed.

S & F 500 litres capacity rotational moulded polyethylene water storage tanks with cover (Cylindrical vertical, with closed top), hoisted and fixed in position all as specified in SSR Part I including taking down old one as directed, complete all as specified and as directed.

3 layer PP-R Polypropylene random copolymer pipes 20mm dia SDR 7.4 & SDR 11 UV stablised and antimicrobial welded having thermal stability for hot and cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to wall, ceiling or in floors etc, complete all as specified and as directed.

S&F in repairs PP-R gate valves 20 mm dia (brass insert) as per requirement of the site, complete all as specified and as directed.

S&F in repairs PP-R Ball valves (brass insert) 20 mm dia as per requirement of the site, complete all as specified and as directed.

S & F in repair Vitreous China wash basin, white, flat back, size 450 x 300mm including cutting for and pinning in ends of brackets or erecting stand but inclusive of fixing of supply and waste pipe, complete all as specified and as directed.

S & F in repair 15 mm bore pillar taps fancy type, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe, complete all as specified and as directed.

S&F in repairs angle stope valves, cast copper alloy, screwed down high pressure with crutch or butter fly handle, fancy type, chromium plated with long shank and cup (concealed type), 15mm bore dia of pipe, complete all as directed by Engr-in-charge.

S&F flush waste pipe of polyethylene of low or high density or PVC ,32 mm dia for urinal/wash basin/ flush tank fixed in repairs, complete all as directed by Engr-in-charge.

S&F in repairs 15 mm dia PVC connection pipe suitable for connecting flushing cistern and WHB etc 450mm long, complete all as specified and directed.

S & F in repairs, waste coupling of PTMT 32mm bore for urinal / wash basin (Half or full threaded ) (Minimum Weight 45 grams), complete all as specified and as directed.

S&F in repairs bib tap cast copper alloy chromium plated butterfly handle screwed down screwed for iron pipe completed (15mm dia tap), complete all as specified and as directed.

S & F in repairs, PVC (SWR) 75 mm dia, floor trap, plain with grating including jointing to waste pipe with solvent cement, complete all as specified and as directed.

S & F in repair CP floor grating doom 125mm dia with waste hole of PTMT (mim weight 40 grms) all as directed by the Engr-in-Charge.

S & F in repair Stainless steel sink with draining board,made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall size 915mmx460mm with bowl size 410mm x 330mm x 160mm, complete all as specified and as directed.

S & F 110 mm dia, PVC (SWR) pipes, single socketed, in any length with rubber ring joints including necessary MS flat iron clamps of size (40x4 mm) laid in trenches or in floors all as specified and as directed by the Engineer - in - Charge.

S & F 75 mm dia, PVC (SWR) pipes, single socketed, in any length with rubber ring joints laid in trenches or in floors all as specified and as directed by the Engineer - in - Charge.

PCC 1:3:6 type C-2 (using 40mm gradded crushed stone aggergate) as in bed to drain pipe incl packing under and hanching against side after they are laid and tested for 110mm dia pipe , complete all as specified and as directed.

PCC 1:3:6 type C-2 (using 40mm gradded crushed stone aggergate) as in bed to drain pipe incl packing under and hanching against side after they are laid and tested for 75 mm dia pipe , complete all as specified and as directed.

M & L for preparation of new steel surfaces over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer, complete all as directed and specified.

M&L for preperation of newly plastered surfaces of walls and applying two coats of cement base paint over a coat of primer(chalk whiting) complete all as specified and as directed.

M&L for preperation of newly plastered surfaces of walls and applying three coats of white wash, complete all as specified and as directed.

M&L for preperation of new wood or wood based surface of any description over 10cm width or girth and applying two coat of synthetic enamal paint over a coat of pink primer, complete all as specified and as directed.

M&L for preperation of existing treatment on steel / CGI sheets of any descripton and applying one coat of synthetic enamal paint (galvanisation should be removed if required) ,complete all as specified and as directed.

M&L for preperation of old wooden joinery, wall & ceiling surface surface any description over 10cm in width or girth and applying one coat of synthetic enamal paint complete all as specified and as directed.

M&L for preperation of old plastered wall surface of any description and applying two coat of white wash, complete all as specified and as directed.

M&L for preperation of old plastered wall surface of any description and applying one coat of cement based paint, complete all as specified and as directed.

Preparation of new plastered or unplastered surfaces of walls and applying two coats of oil bound distemper including a coat of primer over 3mm thick wall care putty complete all as specified and as directed.

Taking down carefully aluminium / copper point wiring light/fan/socket or power complete including unscrewing from board fitting and fixture such as switches, sockets, ceiling roses, lamp holders, brackets, pendent holder , light fittings , regulators, distribution/ Meter boards, MCBs etc and making good the distturbed surface matching with existing specifications complete all as specified and directed.

Point wiring for one light point or fan point controlled by one switch with 1.50 Sqmm, PVC insulated, unsheathed, FRLS single core, multi-stranded, copper conductor cable, 1100 Volts, drawn in and including PVC casing and capping, fire resistance, ISI marked, fixed surfaces of walls and ceilings, terminated in and including rectangular PVC board for mounting fitting/ switches/ sockets and 1.50 Sqmm, copper conductor, multi-stranded, FRLS as earth continuity wire connected to earth terminal, including making good to disturbed surface as matching to existing descriptions/ specifications, complete all as specified and as directed.Make : Havells/ Polycab/Finolex

Description all as per serial item No- 105.00 here-in-before but for 5 Amps 3 Pin Socket outlet on same board, complete all as specified and as directed.

Description all as per serial item No- 81.00 here-in-before but for 5 Amps 3 Pin socket outlet on independent board, complete all as specified and as directed.

Point wiring for 3-pin, 15 Amps, socket outlet on independent board with 2.5 Sqmm, PVC insulated, unsheathed, FRLS single core, multi-stranded, copper conductor cable, 1100 Volts, drawn in and including PVC casing and capping, fire resistance, ISI marked, fixed surfaces of walls and ceilings, terminated in and including rectangular PVC board for mounting fitting/ switches/ sockets and 1.5 Sqmm, copper conductor, multi-stranded, FRLS as earth continuity wire connected to earth terminal complete all as specified and as directed.

Point wiring on independent board with 4.00 Sqmm, PVC insulated, unsheathed, FRLS single core, multi-stranded, copper conductor cable, 1100 Volts, drawn in and including PVC casing and capping, fire resistance, ISI marked, fixed surfaces of walls and ceilings, terminated in and including rectangular PVC board for mounting fitting/ switches/ sockets and 4.0 Sqmm, copper conductor, multi-stranded, FRLS as earth continuity wire connected to earth terminal complete all as specified and as directed.

Supply and Fixing in repairs switch socket combination 3 pin 5 Amps, flush type, universal complete all as specified and as directed.

Supply and Fixing in repairs switch socket outlet 2 in 1, 3 pin, 5 Amps, 240 Volts flush type complete all as specified and as directed.

Supply and Fixing in repairs switch socket outlet 2 in 1, 3 pin, 5/16 Amps, 240 Volts flush type complete all as specified and as directed.

Supply and Fixing in repairs switch piano, flush type, single pole, one way, 5 Amps, complete all as specified and as directed.

Supply and Fixing in repairs ceiling rose, surface bakelite 65 x 50 mm two or three terminals complete all as specified and directed.

Supply and Fixing in repairs sheet metal enclosures for distribution box for MCBs, Single pole and neutral, 8 way with, 240 Volts, double door, with 200 Amps rated bus bar blank plate complete all as specified and directed.

Supply and Fixing in repairs MCB, single pole and neutral, 63 Amps, 240 Volts , 10 KA C series, complete all as specified and directed.

Supply and Fixing in repairs MCB, Double pole, 40 Amps, 240 Volts , 10 KA C series, complete all as specified and directed.

Supply and Fixing in repairs MCB , single pole, 6 to 32 Amps, 240 Volts, 10 KA C series, complete all as specified and directed.

Supply and Fixing in repairs lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings,with & including 10 watt LED lamp complete all as specified and as directed.

Labour only for taking down carefully and re- fixing at same position after completion of false ceiling work with suitable fixing material for exusting Recess mounting 2'x2' LED light fitting 36 Watt including with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed.

Supply and Fixing lamp holder, PVC/ Polycarbonate type with back plate suitable for batten fittings,with & including taking down old complete all as specified and as directed.

Supply and Fixing LED Light fitting including LED tube light batten type 1x20 watt, mounted on integrated sleek extruded polycarbonate LED channel with white accrylic cover suitable for 230 Volts, 50 Hz cool white colour bipin holder, connector block etc complete with all accessories internally prewired and including connecting up with twin core twisted flexible copper concuctor cable of suitable size complete all as specified and as directed. Make Havells Cat Part No. STOUTPLUS600BS20WLED840SPCWH or Equivalent model of Make: Crompton/ Phillips/ Bajaj.

Supply and Fixing LED light energy saving and environment friendly long life verstile pressure die cast aluminium, IP 66 street light of 48 watt 5700K 240 Volts single phase LED light suitable for 50mm dia pipe for fixing on wall including connection with suitable size 3 core PVC cable complete all as specified and as as directed.Make Havells Cat Part No.ENDURAPEARLNEOSL48WLED757SASYTOPC or equivalent of Make:Bajaj/ Philips/ C&G.

Supply and Fixing LED light energy saving and environment friendly long life verstile pressure die cast aluminium, IP 66 street light of 25 watt 5700K 240 Volts single phase LED light suitable for 40mm dia pipe for fixing on wall including connection with suitable size 3 core PVC cable complete all as specified and as as directed.Make: Havells/Bajaj/ Philips/ C&G.

Supply and Fixing LED bulk head light fitting 1x10 Watt 230 volt attractive wall / Ceiling mounted any type with white reflector complete with all accessories prewired and including connecting up with twin core twisted flexible copper concuctor cable of suitable size complete all as specified and as directed. Make Havells Cat Part No. RUGBYNEONFT10WLED860SSYMTOPC or Equivalent model of Make: Phillips/ Bajaj/CG.

Supply and fixing in replacement Endura Slim Pro Plus 2' x 2' recess mounting warm white LED luminaries white powder coated sheet housing LED front frame with translucent cover fixed to the housing fixed in front frame 36 x 1 watt LED extruded aluminium heat sink projected in false ceiling complete all as specified and as directed .Make: Endura Slim Pro Plus Cat part No. ENDURASLIMPROPLUS2X2PLR28/36WLED857MOD or equivalent in Havells/ Bajaj/ Crompton/Phillips

Supply and Fixing factory made epoxy powder coated Distribution Board double door TP & N 4 ways (TPN MCB DB) with metal door (IP-43 protection) fabricated from minimum 1.6 mm thick CRCA sheet and fixed flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with suitable for one MCB TPN , 415 volts 63/40 Amp, 10 KA as incomer and 12 SP MCBs /3 TPN MCBs outgoing complete all as specified and conforming to IS 8623 and as directed. Make Legrand Cat Part No. 607715 or Equivalent model of Havells / C&S.

S&F submain wiring of four single core PVC insulated cables FRLS with copper conductor of size 4x6 Sqmm for phase and neutral and 2x4 Sqmm for earth and drawing in to caping/casing complete including taking down old wiring with making good disturbed surfaces with as per existing, complete all as specified and as directed. Make: Havells/polycab/RRkabel

Supply and Fixing in repairs MCB TPN 63 Amp 415 Volts, connecting with copper lugs complete all as specified and as directed.Make: Legrand/ L&T / Seimens.

XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) with multi-standard aluminium conductor, 1100 volts grade, cross sectional area 25 Sqmm 3.5 core, laid in trenches or passing through pipes, including making necessary connections at both ends, complete all as specified and directed.

Supply and laying of fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with and inner sheating of PVC tape armoured with galvanized steel wire or tape armoured with galvanized steel wire or tape and over all PVC sheathed 10 Sqmm x 04 core nominal cross section in service connection complete all as specified.

Excavation in trenches n. exc 1.5m wide and n. exc 1.5 m deep for taking out / laying of under ground cable/ erecting of poles / stay in any of soil complete all as specified and as directed by the Engineer-in-Charge.

Returning filling in incl spreading levelling watering and well ramming in layers n. exc 25cm thick complete all as specified and as directed by the Engineer-in-Charge.

Removing excavated soil to a distance n exc 50m and depositing at a level n exc 1.5m above the starting point complete all as specified and as directed by the Engineer-in-Charge.

Sand cushioning to protection of underground cables, laid 8 Cm before laying and 15 Cm after laying of cable, and punned to form an overall layer of 18 Cm thick, complete all as specified and as directed by the Engineer-in-Charge. Note: Punned thickness shall be measured.

Supplying and laying in replacement un-reinforced precast concrete cable cover, Class LV, Type-I, flat, size 250mmx150mmx40mm, complete all as specified and as directed by the Engineer-in-Charge.

Sub main wiring for circuit/ submain wiring alongwith earth wire with two run of 6.0 Sqmm of FRLS, PVC insulated copper conductor, single core cable, multi stranded, FRLS, ISI marked, 1100 Volts grade and one run of 6.0 Sqmm, FRLS, PVC insulated copper conductor, single core cable, multi stranded, ISI marked, 1100 Volts grade as earth wire connected to earth terminal, drawn in and including PVC casing and capping, fire resistance, ISI marked, fixed on surfaces of walls/ ceilings complete all as specified and directed.

Sub main wiring for circuit/ submain wiring alongwith earth wire with two run of 4.0 Sqmm of FRLS PVC insulated copper conductor, single core cable, multi stranded, FRLS, ISI marked, 1100 Volts grade and one run of 4.0 Sqmm, FRLS, PVC insulated copper conductor, single core cable, multi stranded, ISI marked, 1100 Volts grade as earth wire connected to earth terminal, drawn in and including PVC casing and capping, fire resistance, ISI marked, fixed on surfaces of walls/ ceilings complete all as specified and directed. Note: two run of 4 sqmm and one run of 4 sqmm wire cable and PVC conduit pipe shall be measured and paid as one run unit.

Taking down existing unserviceable/old DBs from any height and any make good complete including disconnection from existing MCBs/Isolator etc complete all as directed.

Taking down existing unserviceable/old MCB (SPN/SP) from any height and any make good complete including disconnection from existing MCBs/Isolator etc complete all as directed.

Supply and Fixing 1100 volts grade heavy duty cable PVC insulated aluminium conductor 6 Sqmm, served with inner sheathing of PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4 mm suspension wire, one twin core cable flat or circular, complete all as specified and directed.

Supply and Fixing (SPN) MCB 40-63 Amps, 240 Volts, 50 Hz AC made from moulded self existing thermostat plastic and suitable 'C' curve 10 KA breaking capacity and terminal box suitable for 16 to 35 Sqmm cable complete conforming to IS 8828 of 1996 and all as specified and as directed.

Supply and Fixing Distribution Board (SPN) MCB 16-40 Amps, 240 Volts, 50 Hz AC made from moulded self existing thermostat plastic and suitable 'C' curve 10 KA breaking capacity and terminal box suitable for 4 to 10 Sqmm cable complete conforming to IS 8828 of 1996 and all as specified and as directed.

Five star rating water heater storage type (Geyser) of capacity 50 ltr complete, single phase 240 volts 50 Hz with cooper inner tank, fix on wall with suitable nut & bolts including grouting in PCC 1:2:4 type B-I using 20mm graded crushed stone aggregate with 02 Nos of PVC connection pipe (hot & cold supply) with suitable size of nuts complete all as specified & directed by Engr-in-Charge .

9 watt LED lamp 230volts 50 Hz Ac, complete all as specified and as directed.

Supply and Fixing in repairs sheet metal enclosures with socket plug top and MCB 20 amps single pole and neutral with a two pin and earth plug and socket complete all as specified and directed.

Supply and Fixing in repairs heavy duty five star rated Exhaust fan AC single phase 230 Volt of size 375 mm sweep with louvers shutters and connecting up including provision of cable from ceiling rose to connector of fan controlled by one way switch complete all as specified and directed. Make: Orient/Usha/Bajaj.

Earthing complete with galvanised iron earth plate electrode 600x600x6mm buried directly in ground (earth pit not less than 2.25mtr deep below ground level) with top edge of earth plate not less than 1.5mtr below normal ground level, connected with 4.0mm dia GI wire as earth lead, by means of bolts, nuts, check nuts and washers of galvanized iron or steel complete with 40mm dia GI light grade protection pipe, 20mm dia GI medium grade watering pipe with funnel including charcoal, dust, salt, PCC M-15, type B-1 in pit with precast RCC M-15(1:2:4), type B-1 (using 20mm graded crushed stone aggregates) in cover reinforced with XPM not less than 4.0 Kg per Sqm, test point etc. all as shown in electric plate No-3 of SSR Part-I (2009), complete with necessary earth work in any type of soil, removal to a distance not exceeding 50mtr, including testing on completion, complete all as specified and as directed by Engineer-In-Charge. Note: Earth pit chamber and RCC pit cover shall be painted with two coats of red synthetic enamel paint over one coat of primer including preparing of surfaces.

M/S Praveen Kumar and Sons

Rampal Singh Contractor

M/S SHAMSHER ALI SUFI

ASHOK KUMAR SHARMA

Mehar Enterprises

VIJAY ENTERPRISES