PROVN OF OFFICE ROOM FLOOR TILING IN BLDG NO P04 OTM ACCN INTERLOCKING TILES AROUND BATHROOM TOILET AND SPL REP TO GD POST NO 5 7 AND 8 UNDER GE NARANGI

Amount

Excavation in trenches n.exc 1.5m wide and not exceeding 1.5 m in depth for foundation etc, or for shafts, wells, cess pits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft / loose soil etc complete all as specified and as directed.

M&L surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil.complete all as specified and directed.

Returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each in soft / loose soil etc complete all as specified and as directed.

Removing of surplus excavated material not exc 50m and depositing where directed at a level n. exc 1.5 m above the starting point etc complete all as specified and as directed.

Cutting into existing manholes for connecting new drain pipe of any size making good to pipe and rendering , cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 th section) in cement concrete 1:2 :4 type B-1 smooth finished and reforming benching as required for 150mm dia ( internal ) pipe complete all as specified and directed.

M&L for hardcore of broken or boulders of gauge not exceeding 63mm deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L providing cement concrete type B-1 ( 1:2:4) using 20mm graded stone aggregate as in roof kerb or mud stops, rounded or chamfered on edges in lintels upto 1.5m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, kneelers, apex stones, bed plates, water troughs, and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) in foundation filliing and mass concrete complete all as specified and as directed.

M&L for RCC 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete etc complete all as directed.

M&L for RCC 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in beams, seimic bands, cantilevers, bressumers and lintels complete all as specified as directed.

M&L for RCC 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in Columns, pillars, piers, posts and struts etc.complete all as specified as directed.

M&L TMT steel bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for TMT bars 6mm to 8 mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified as directed.

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified as directed.

M&L Formwork to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified as directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L for brick work with old size sub class 'B' bricks straight or curved on plan exc. 6m mean radius and built in CM 1:4 etc complete all as specified as directed.

M&L for brick work with old size sub class 'B' bricks straight or curved on plan exc. 6m mean radius and built in CM 1:6 etc complete all as specified as directed.

M&L for brickwork with subclass ‘B’ old sized bricks, straight or curved on plan to any radius in half brick thick walls and built in CM 1:4 etc complete all as specified as directed.

M&L for 40mm thick damp proof course 1:2:4 type B-0 and applying evenly a tack coat of blown bitumen 85/25 @ 1.20 kg per sqm including laying 150micron thick polythene film complete all as specified as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm each including builders hardware complete all as specified and as directed.

Taking down shutter of any description exc 1 Sqm but n exc 2 Sqm each and refixing in the same opening complete all as specified and directed.

Taking down shutter of any description exc 2 Sqm each and refixing in the same opening complete all as specified and directed.

Taking down steel window, ventilator frame without taking off shutter from the frame of any description including guard bars/grills etc. not exceeding 1.00 sqm each complete all as specified and directed.

S & F factory made steel windows with side hung shutters glazed shutter including both side openable (out side glazed window and inside fly proof window) including projecting type hinges with steel handle and steel peg stay complete with glazing bars and 12 mm square bar or round bar of approved design welded to steel window frame dovetailed or welded complete all as specified and directed . Note: Guard bar or square bar shall be measure and paid separately.

S&F steel window and ventilator fixed type complete with glazing bars dovetailed or welded ready for wire mesh/glass panes complete.

S&F 30 mm thick Factory Made Solid Panel PVC Door Shutter consisting of frame made out of M.S. tubes of 19mm x 19mm for stiles, & 15mm x 15mm for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC sheet 5mm thick ‘C’ channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and plain colour PVC sheets for top rail, lock rail & bottom rail on either side, and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with PVC sheet beading, and joined together with solvent cement adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s instructions and drawing. The width of stiles & rails will be in proportion to the width of the door shutter as per SSR Clause No 8B.2.1

M&L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing etc complete all as directed.

S & F anodized aluminium push pull type glazed dooor shutter single leaf including necessary jointing cleats, glazing clips, rubber packing, snap beading, screws, handle, locking arrangement, 5.5 mm thick float glass tinted quality on both panels including aluminium door closer complete all as specified and as directed. Aluminium sections : 'A' series (i) Top, , bottom and Lock rails :- 85.00 mm x 44.45 mm x 1.20 mm thick (ii) Shutter vertical rail : 47.62 mm x 44.45 mm x 1.20 mm thick (iii) frame top and sides :- 63.50 mm x 38.10 mm x 1.20 mm thick

S & F anodized aluminium three track sliding window with approved make of following sections glazed shutter as per standard engineering practice including all accessories complete with 5.00mm thick glass panes, rubber beading etc. complete all as specified and as directed. Aluminium sections : 'A' series (i) shutter Top,& bottom :- 37.50 mm x 15.00 mm x 1.10 mm thick (ii) Shutter interlock : 37.50 mm x 23.00 mm x 1.10 mm thick (iii) shutter side :- 37.50 mm x 23.00 mm x 1.10 mm thick (iv) frame bottom :- 92.00mmX26.00mmX1.00mm thick (v) Frame top and sides :- 92.00mmX26.00mmX1.00mm

S&F aliminium body Door closure hydraulically regulated, designation no 3 ,universal type, suitable for door shutters of 851 to 1000mm in width and of weight between 61 to 80 kg and fixed complete all as specified & as directed.

S & F 100mm size stainless steel butt hinges, medium weight, and fixed etc complete all as directed.

S & F 75mm size stainless steel butt hinges, medium weight, and fixed etc complete all as directed.

S&F 150 mm size aluminum anodised, barrel tower bolts of extruded section etc complete all as directed.

S&F 200 mm size aluminum anodised, barrel tower bolts of extruded section etc complete all as directed.

S&F 125 mm long extruded anodized aluminum alloy handles, cast type, etc complete and directed.

Dismantling of asbestos cement sheet (corrugated or semi corrugated etc) as in roof covering complete all as specified and as directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws complete all as specified and directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated plain steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws as specified complete all as specified and directed. Note: To be executed for provision of ridges and hips.

S&F in repair suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600mmx600 mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick High Pressure stean Crude Everest Non Asbestos Fiber Cement designer Board (E-Board Classic) in & including a grid of GI system duly suspended with T section 38 x 24 x 0.7mm, wall/cleat 25 x 25 x 0.35 mm and suspender 4mm dia GI wire hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures,air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc.The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall,Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610mm c/c,so as to form 600mm x 600 mm grid complete all as specified and as directed.

S&F suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600mmx600 mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick High Pressure stean Crude Everest Non Asbestos Fiber Cement designer Board (E-Board Classic) in & including a grid of GI system duly suspended with 4mm dia GI wire hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures,air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc.The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall,Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610mm c/c,so as to form 600mm x 600 mm grid complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified & as directed.

S&F Rolled sections as in main and cross beams, hip and jack rafters, purlins where connectwd to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates confirming to Fe 410-W ( Gde E-250 Quality B)complete all as specified & as directed.

S&F rolled mild steel plates ( plain or chequrred) channels, square cut or notched ( ordinary or counter sunk) forming holes, with riveted, bolted or welded attachment complete all as specified & as directed.

Demolition of un reinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in subase of floor complete all as directed.

M&L for sand filling under floor or in foundation including watering and consolidation complete all as directed.

M & L for 25 mm thick PCC 1:2:4, type B0 (using 12.50 mm graded stone aggregates) as in sub base complete all as specified and as directed.

M & L for 100 mm thick PCC 1:2:4, type B0 (using 12.5 mm graded stone aggregates) as in path / paving / hard standing / floor and finished the surface even and smooth without using extra cement complete all as specified and as directed.

M & L for 100 mm thick PCC 1:2:4, type B2 (using 40 mm graded stone aggregates) as in path / paving / hard standing / floor and finished the surface even and smooth without using extra cement complete all as specified and as directed.

M&L for 75 mm thick, PCC 1:3:6, type C1 (using 20 mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide and 30 mm deep at every 2.4 mtrs interval filled with bitumastic compound etc complete all as specified and as direted.

M & L for water proofing treatment to RCC roof slab, including parapet comprising with the following of treatment/specification from bottom to top:- (i) Taking out old roof treatment and roughening the concrete roof surfaces by picking, sweeping clean and washing down with water to remove dust etc and disposal of rubbish not exceeding 100 mtr distance from starting point. (ii) Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 mixed with water ptoofing compound @ 3% of weight of cement or as per manufactures instructions and surface finished even and smooth without using extra cement after applying a coat of cement slurry @ 3 kg/sqm for laying APP membrane. (iii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (iv) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 160 gms/Sqm) shall be applied over bituminous primer as specified above over by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (v) Applying two coat of aluminium paint over the APP modified membrane @ 0.11Kg/sqm.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc. and neat cement slurry with 3.0 kg/sqm complete all as specified and as directed .

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.38 sqm, as in vertical surfaces such as skirting/dados etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 10mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for 20-25mm thick Kota stone flooring laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 20 mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for 20-25mm thick Kota stone slab in riser of steps, skirting, dado and pillar laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over 10 mm thick screed bed in CM 1:3 complete all as specified and directed.

M&L for 10mm thick Vitrified tiles light shade area of each tile n exc 0.36sqm laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for 10mm thick Vitrified tiles light shade area of each tile n exc 0.36sqm as in vertical surfaces such as skirting/dados etc etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 10mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 450x300x7mm/350X250X7mm thick / 300X450X7mm thick set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as skirting, dados and risers to steps etc over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 grade with 30mm thick sand cushioning with proper compacting through vibratory compaction by using plate vibrator including filling the joints with sand complete all as specified & as directed.

M&L in repair heavy duty parking tiles of size 300mmX300mmX10 to 12mm thick/ 400mmX400mmX10 to 12 mm thick of approved make jointed in neat cement slurry, pointed in white or coloured cement to match colour of tiles, over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified and as directed.

Taking down cement plaster on walls, chajja surfaces, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L rendering 5mm thick plaster on ceiling,soffits of slab etc in CM 1:3 finished the surface even and fair without using extra cement complete all as specified and directed

M&L for 10 mm thick rendering in CM 1:6 on brick/ concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:6 on brick/ concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4), in two layers, under coat of 10 mm thick & top of 5 mm thick, to other than fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound (@ 2% by weight of cement or as per manufacture's instructions), finished even and smooth without using extra cement complete all as specified and as directed. Note : Water proofing compound will be measured and paid separately as "Supply only".

Supply only integral water proofing compound complete all as specified and as directed.

M&L for preparation of newly plastered surface of ceiling and applying three coats of white wash complete all as specified and directed.

M&L for preparation of newly plastered surface of wall and applying three coats of white wash on wall surface complete all as specified and directed.

M&L for preparation of old plastered surfaces of wall applying one coat of distemper oil emulsion complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall applying 1mm thick wall care putty on plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and as directed.

M & L for preparation of new plastered surfaces of wall and applying two coats of acrylic exterior weather resistanr paint ( weather proof paint) over a coat exterior primer complete all as specified and as directed.

M & L for preparation of new plastered surfaces of wall and applying two coats of acrylic exterior weather resistanr paint ( weather proof paint) over a coat of wall care putty and exterior primer complete all as specified and as directed.

M & L for preparation of old plastered surfaces of wall and applying one coat of acrylic exterior weather resistanr paint ( weather proof paint) complete all as specified and as directed.

M&L for preparation of old steel or iron surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paints complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50sqm in each pane frosted on both side complete all as specified and directed.

Taking up or down 15 mm bore GI tubing from trenches / wall including all fittings complete all as specified and as directed. Note : Excavation and earthwork if any shall be included in the quoted rate

S&F GI tubing15 mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Taking up or down 20 mm bore GI tubing from trenches / wall including all fittings complete all as specified and as directed. Note : Excavation and earthwork if any shall be included in the quoted rate

S&F GI tubing 20 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors complete all as specified and as directed.

S&F GI tubing 25 mm bore, medium grade with all fittings and laid in trenches complete all as specified and as directed.

M/L cutting chases , pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring,etc. and making good , cutting not exceeding 10cm girth complete all as specified and directed.

S & F in repair bib taps, 15mm dia cast copper alloy chromium plated, fancy type with crutch or butter- fly handles screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S & F bib taps, 15mm dia cast copper alloy chromium plated, fancy type with crutch or butter- fly handles screwed down for iron pipe or for brass ferrule complete all as specified and as directed.

S&F in repair stop valves/ angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F stop valves/ angular stop valve, 20mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F in repair 15mm bore dia of concealed stop valves cast copper alloy fancy type chromium plated with long shank and cup complete all as specified and as directed.

S&F in repair 15mm bore pillar taps, cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

S&F 15mm bore pillar taps, cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and as directed.

S&F stainless steel grating doom 100mm dia complete all as specified and as directed.

S & F gun metal gate valve, with iron wheel head, screwed both ends for iron pipe and fixed suitable for 25 mm bore GI pipe complete all as specified and as directed .

S & F gun metal gate valve, with iron wheel head, screwed both ends for iron pipe and fixed suitable for 20 mm bore GI pipe complete all as specified and as directed .

S & F PVC connection pipe 15mm dia and 450 mm long with PVC PTMT nuts at each ends with rubber washers complete all as specified and directed.

S & F 32mm dia PVC waste pipe complete all as specified and directed.

S & F grating doom 100mm dia of stainless steel complete all as specified and directed.

S&F Cast iron floor trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B-I ( 1:2:4) complete all as specified & as directed

S & F PVC (SWR) floor trap 75mmdia with grating including jointing to waste pipe fixed in cement concrete 1:2:4 type B-1 complete all as specified and as directed.

S&F in repair rotational moulded polyethylene water storage tank 1000 litre capacity of triple layered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S & F vitreous china, wash hand basin, coloured, flat back size 550 mm x 400 mm including brackets including pillar tap, 15 mm bore chromium plated, cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia PVC connection pipe complete all as specified and as directed

S & F in repair vitreous china, wash hand basin, coloured, flat back size 550 mm x 400 mm including brackets including pillar tap, 15 mm bore chromium plated, cast copper alloy with capstan heads, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia PVC connection pipe complete all as specified and as directed

S&F vitreous china wash down water closet (padestal pattern) including connection to drain (or outgoing pipe) and flushing pipe, anti syphonage pipe, trap set and including white or black seat cover for padestal pan with mild steel chromium plated aluminium hinging device, fixed to pan with suitable screws etc complete all as specified and as directed.

S & F in repairs, Vitreous China Squatting Pan"Orissa pattern" size 580 mmx440 mm white with integral foot rest etc. ( excluding cistern and flush pipe) including S or P Trap and provision of concrete bedding and making good to floor complete all as specified and as directed.

S&F PVC low level flushing cistern 10 litres capacity with inlet ball valve, float and handles including brackets complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres capacity with inlet ball valve, float and handles including brackets complete all as specified and directed.

S & F in repairs, PVC connection pipe 15mm dia and 450 mm long with PVC PTMT nuts at each ends with rubber washers complete all as specified and directed.

S&F in repair chromium plated soap dish of approximate size 160x160x90mm embedded in wall complete all as specified & as directed.

S & F in repairs, 110mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall, ceiling or laid in floors complete all as specified and as directed.

S & F in repairs, 75mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints fixed to wall, ceiling or laid in floors complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and laid in trenches complete all as specified and directed.

S&F 75 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends of any radius complete all as specified and directed.

S&F 110 mm dia PVC (SWR) bends of any radius with access door complete all as specified and directed.

S&F 75 mm dia PVC (SWR) bends of any radius with access door complete all as specified and directed.

S&F PVC ( SWR) branch piece, single ( single -Y) equal or unequal 110mm dia complete all as specified & directed.

S & F 110mm bore PVC ( SWR) junction, single (Single T) equal or unequal with oval access door complete all as specified and directed.

Taking down ceiling Exhaust/Wall fan, carefully including connecting wires and transporting from any location inside army area to MES E/M store yard, and refixing on same location or other location after repairing/painting with synthetic enamel paint ( Duco) using spray painting machine with filling of cavities replacing damaged hook, clamp, pipe etc complete all as specified and as directed.

Taking down carefully aluminium/ copper point wiring for light/fan/ socket/bell or power point incl. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete removing materials to store for keeping in safe custody site or handed over to contractor as schedule of credit and making good disturbed surfaces of walls, floors, etc complete all as directed by Engineer-in-Charge.

M&L point wiring with PVC insulated and unsheathed cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts, FRLS grade cable conforming to IS-694 1990 drawn in and including concealed conduit withwith all accessories including metal flush box/PVC modular box and cover plates for mounting modular switches, sockets , regulators etcand 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for One light or fan point controlled by one 5 Amps switch one way complete all as specified and directed.

All as per item No 126 here-in-before but for one 3 pin 5 Amp switch socket outlet on independent board

All as per item No 126 here-in-before but for one 3 pin 5 Amp socket outlet on same board with other switches.

All as per item serial No 126 here-in-before but One 3 pin socket modular outlet 5 amps on the same board with other switches

All as per item serial No 126 here-in-before but One modular socket outlet 3 pin 5/6 Amp on independent board.

All as per item serial No126 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable.

S&F modular switch one way 6 Amps 1 module complete all as specified and as directed.

S&F modular switch one way 16 Amps 1 module complete all as specified and as directed.

S&F modular socket 6 Amps 2/ 3 pin, combined 2 module complete all as specified and as directed.

S&F modular socket 16 Amps 2/ 3 pin, combined 2 module complete all as specified and as directed.

S&Fmodular fan regulator, 120 W two module size, complete all as specified and directed.

S&F switch piano, flush type single pole one way 5 Amps 230 volt complete all as specified and as directed.

S&F socket outlet 3 pin, 2-in-1, 5 Amps flush type complete all as specified and as directed.

S&F switch socket combination outlet 5 pin, 2-in-1, 5 Amp flush type complete all as specified and as directed.

S&F switch socket combination multipurpose, 2 in 1, 6 pin, 5 & 15 Amp flush type complete all as specified and as directed.

S&F ceiling rose surface bakelite 65x50mm three terminal complete all as directed.

S&F lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as directed.

S&F in repair LED light fitting of approved make 1X 10 W, 220V, AC decorative batten type with driver, holder including LED lamp and connecting up with three core flexible copper conductor cable of suitable size complete all as directed.

S&F in repair LED light fitting of approved make 1X 20 W, 220V, AC decorative batten type with driver, holder including LED lamp and connecting up with three core flexible copper conductor cable of suitable size complete all as directed.

S&F LED light fitting of approved make 1X 20 W, 220V, AC decorative batten type with driver, holder including LED lamp and connecting up with three core flexible copper conductor cable of suitable size complete all as directed.

S&F in repair Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagonal bulk head black-lit LED10 W -IP-66 luminaire comprising of high brightness LEDs complete all as specified and as directed.

S&F Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagonal bulk head black-lit LED10 W -IP-66 luminaire comprising of high brightness LEDs complete all as specified and as directed.

S&F LED building security light fittings of approved make 35 W 230 V AC outdoor type with high pressure diecast aluminium housing and heat resistant complete with driver, lamp, bracket with impact and corrosion resistant including thermal management in multiple optics complete wit IP 65/66 protection complete all as directed.

S&F in repair LED building security light fittings of approved make 60 W 230 V AC outdoor type with high pressure diecast aluminium housing and heat resistant complete with driver, lamp, bracket with impact and corrosion resistant including thermal management in multiple optics complete wit IP 65/66 protection complete all as directed.

M&L building secruity light bracket made out of 40 mm bore medium grade GI Pipe with two sets clamps, with nuts and bolts, bend to shape for fixing street light luminaries all as directed, length of GI Pipe shall not be less than 2.0 mtrs complete all as specified and directed.

S&F LED luminaire 600X600mm, 35/36 Watt, 220V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders and LED lamps suitable for roof ceiling including connecting up with three core flexible copper conductor cables of suitable size complete all as directed.

S & F in repair SPN DBs 4 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 200 Amp rating copper bus bar complete all as specified and as directed.

S & F SPN DBs 8 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 200 Amp rating copper bus bar complete all as specified and as directed.

S&F MCBs, SP 6 to 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed.

S&F MCBs, SPN 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed.

S&F MCBs, SPN 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed.

S&F ceiling fan complete with blades, down rods, electronic regulators and accessories, 230 V 1200mm sweep, minimum air delivery 210 CFM with service value 6.00BEE, five star rating with bushless direct current motor ( BLDC)complete all as specified and directed.

Supply, laying and testing of XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 10 sqmm 3 core laid in trenches / floor or fixed on wall /pole with brass compression cable glands, terminal lugs etc, complete all as specified and as directed.

Supply, laying and testing of XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 10 sqmm 2 core laid in trenches / floor or fixed on wall /pole with brass compression cable glands, terminal lugs etc, including taking up/down old cable of any description and size complete all as specified and as directed.

Supply and laying 40mm bore GI tubing light grade for cable protection and fixing to existing pole with flat iron MS clamps of size 25X3mm including nuts, bolts, etc. complete all as specified and directed.

Supply and spreading fine dry river sand for cushing to UG cable including spreading levelling and hand punning etc complete all as specified and directed.

M&L for sub class 'B' old size bricks laid in trenches for cable protection laid flat width wise along the length of cable complete all as specified and directed.

S&F in repair ceiling fan complete with blades, down rods, electronic regulators and accessories, 230 V , 1200mm sweep with minimum air delivery 210 CFM with service value 6.00 BEE five star rated with bushless direct current motor (BLDC) complete all as specified and directed.

S&F in repair of Exhaust fans AC single phase 230/ 240 V ,50 Hz metallic heavy body of size 300 mm sweep, 1400 RPM with louver fixing with 4 no hold fastener nut and bolt with washer and connecting with flexiable PVC insulated multistranded copper conductor cable of size 1.5 sqmm including civil work opening on wall of suitable size and 400x400x6mm thick BWR graded plywood making suitable hole for fixing stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and writing MES No. with black synthetic enamel paint with 2cm high letter and making good surface complete all as specified and directed.

Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009 including demolition of old earthing complete.

Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009

Ms Sukumar Talukdar and Co.

Tarun Deka

Pusphas Construction Pvt Ltd

M/S M Ahmed and Co.

SHANKAR ENTERPRISE