REPAIR REPOLISHING OF WOODEN FURNITURE ITMES LIKE BED CHAIRS AND SOFAS ETC TO OTM MD ACCN UNDER GE NORTH DELHI CANTT 10

Amount

BED PLY TOP WITH MNF SET/BED NEWAR WITH MNF SET/COT PLY TOP (1980mmx900mmx660mm) FD-213/FD-214/FD-245/ FD-246 or similar

S&F 12mm thick plywood BWR Grade, approved quality in single piece as per drawing without any joint to the bed frame with suitable screws wood/steel including removal of damaged ply wood all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to 1st quality teak wood long rail 35mm x 90mm in section as per existing size of Bed including removal of damaged long rail all as specified on drawing or as directed by Engineer-in-charge. (Each long rail will be measured as single unit)

All as per item No. 1.01, but short rail all as specified on drawing or as directed by Engineer-in-charge. (Each short rail will be measured as single unit)

S&F in reapirs to new 1st quality teak wood stiffeners of size 40 x 60mm complete including removal of damaged stiffiners all as specified on drawing or as directed by Engineer-in-charge.

S&F in reapirs to 4mm thick one side teak finished plywood of size 780 x 340mm including 12mm dia half cut teak wood beading of both side of head board including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge.

S&F in reapirs to 4mm thick one side teak finished plywood of size 780 x 180mm including 12mm dia half cut teak wood beading of both side of foot board including removal of damaged ply all as specified on drawing or as directed by Engineer-in-charge.

S&F in repairs to flat iron of mild steel of size 35mm x 5mm, bents to right angle on each corners of Bed Hard all as specified on drawing or as directed by Engineer-in-charge.

BIN SOILED LINEN SMALL (750mm x 450mm x 450mm) FD-212/FD-244

Recaning of repaired Bin soiled linen on both sides with best quality of approved plastic cane 2mm wide 0.4mm thick cane and border with 3x0.60 mm cane of white or cream ivory all as specified on drawing or as directed by Engineer-in-charge. (Note: Each side will be mesured as single unit).

Book Case /Book case open small FD-237/FD-355

Removing of old unserviceable top from Book Case and supply and fixing new top made out of 18mm thick pre-laminated particle board teak faced with 4 mm thick teak wood beading all-around the top of all as shown on drawing and as directed.

All as per srl item No 3.01 here-in-before but top shelf.

All as per srl item No 3.01 here-in-before but side of Book case.

Removing old broken/unserviceable legs from book case and S&F new legs of Ist class hard wood teak as per shape and size shown in drawing including french polishing to match the other parts complete all as specified and directed.

Removing old broken/unserviceable doors from the book case and S&F new doors made out of 18mm thick pre-laminated particle board teak faced as per shape and size shown in drawing with piano type hinges complete all as specified and directed.

Removing of old unserviceable back ply of book case and supply and fixing the new back ply of same size made out of 06 mm thick commercial plywood (ISI marked) all as shown in drawing and as directed.

CHAIR DINING/CHAIR DINING PVC SEAT (440MMx430MMx890MM) FD-228/FD-279/FD/MAP-II/05 or similar

Removing the existing unserviceable rear leg and providing with new Teak wood rear leg of size 30x55x890 mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Teak wood front leg of size 30x55x460mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable back rest and proving new Teak wood back rest of size 45x15 slightly curved out of size 45x35mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Teak wood front rail of size 30x65mm drilling holes at 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail of size and proving new Teak wood rear rail including drilling holes at 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable side rails and providing new Teak wood side rails of size 30x65 mm including drilling holes at 12.5mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing of old unserviceable/broken PVC seat from chair dining and S&F new PVC seat 4mm thick in single piece all as per shape and size shown on drawing and as directed by Engineer-in-charge.

Recaning of repaired chair dining with best quality of approved plastic cane 2mm wide, 0.4mm thick and border with 3x0.60 mm cane of white or cream ivory all as specified on drawing or as directed by Engineer-in-charge.

CHAIR DINING LONG BACK/CHAIR DINING CUSHIONED FD-357/FD/E6/MAP/10(R) or similar in MAP /TP

Removing the existing unserviceable rear leg from chair dining long back and providing with new Teak wood rear leg of size 25x50x1200 mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg from chair dining long back and providing with new Teak wood front leg of size 25x50x450mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Teak wood front rail of size 25x50x450mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail of size and proving new Teak wood rear rail of size 25x50x450mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing of old unserviceable/damaged existing cushioned Seat from chair providing new seat made of 75mm thick 40 density foam cushion over 12mm thick commercial plywood BWR grade duly covered with best quality tapestry complete all as specified on drawing or as directed by Engineer-in-charge. Sample of tapestry shall be approved by GE.

CHAIR WRITING (535MMx470MMx890MM) FD-202/FD-250/FD-280

Removing the existing unserviceable rear leg and providing with new Teak wood rear leg of size 55x30x890mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Teak wood front leg of size 55x30x660mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable back rest and providing new Teak wood back rest of size 50 x 15mm slightly curved made out of 50x35mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Teak wood front rail of size 30x65mm including drilling holes at @ 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail and providing new Teak wood rear rail of size 30x65mm including drilling holes @ 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable side rails and providing new Teak wood side rails of size 30x65mm including drilling holes @ 12.5mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest of size 60x25 mm and providing new Teak wood arm rest complete all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair writing with best quality of approved plastic cane 2mm wide, 0.4mm thick and border with 3x0.60mm cane of white or cream/ivory all as specified on drawing or as directed by Engineer-in-charge.

CHAIR EASY FD-229 or Similar

Removing the existing unserviceable rear leg and providing with new Teak wood rear leg of size 55x25 mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Teak wood front leg of size 50x25mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken arm rest and providing new Teak wood arm rest of size 65x25x610mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front frame and providing new Teak wood front frame of size 55x25 mm including drilling holes @ 12.5 mm C/C complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing new Teak wood front rail of size 50x25 mm complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rails and providing new Teak wood rear rails of size 50x25mm complete all as specified on drawing or as directed by Engineer-in-charge.

Recaning of repaired chair easy seat and back of approved quality white or cream ivory with 2mm wide, 0.4mm thick cane and border with 3x0.60 mm cane complete all as specified on drawing or as directed by Engineer-in-charge.

CHAIR WOODEN BOTTOM WITHOUT ARMS FD-225, FD-285

Removing of existing unserviceable seat and provide new seat made out of 6mm thick plywood commercial BWR grade to Chair wooden bottom with wood/steel screws, rest all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear leg and providing with new Teak wood rear leg complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front leg and providing with new Teak wood front leg complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable side rail and providing with new Teak wood side rail complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable front rail and providing with new Teak wood front rail complete all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable rear rail and providing with new Teak wood rear rail complete all as specified on drawing or as directed by Engineer-in-charge.

Replacement of unservicable back rest.

COMMON FOR ALL CHAIRS

Removing the existing unserviceable stiffeners and providing new Teak wood 2nd class hard wood stiffeners of size 25x20 mm complete all as specified on drawing or as directed by Engineer-in-charge. FD-228/ 279/280/225/285 or similar

PEG TABLE (450MMx300MMx380MM) FD-236/FD-277/FD-384

M & L for removing the existing unserviceable leg and providing with new Teak wood leg complete all as specified on drawing or as directed by Engineer-in-charge.

M & L for removing the existing unserviceable top rail and providing with new Teak wood top rail complete all as specified on drawing or as directed by Engineer-in-charge.

M & L for removing the existing unserviceable bottom rail and providing with new Teak wood bottom rail complete all as specified on drawing or as directed by Engineer-in-charge.

All as per Sl item No 10.01 here-in-before but stiffener of Peg table.

Removing of old unserviceable top from peg table and S&F new top made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and as directed by Engineer-in-charge.

SOFA SET 4/ 5 PERSON WITH CUSHION FD-281/FD-373

Removing the existing unserviceable cushion of sofa set, tapastry cloth and replacing with new foam cushion 40 density 100mm thick of size 558mm x 533mm x 100mm duly covered with new tapastry cloth including mulmul completly stiched, rest all as shown on drg and as directed by Engr-in-Charge. Note :- (i) Each cushion for seat or back will be measured as single unit. (ii) The tapastry cloth shall be mat finish and shall not less than Rs. 350/- per metre and as approved by GE.

Removing the existing unserviceable tapastry cloth of sofa set and replacing with new tapastry cloth mat finish of size 558mm x 533mm x 100mm with mulmul cloth. Note : tapastry cloth costing not less than Rs. 350/- per metre and as approved by GE.

Removing the existing unserviceable front leg from Sofa and providing new first class teak wood of leg size 70mm x 35 mm x 495mm, rest all as shown on drg and as directed by Engr-in-Charge.

Removing the existing unserviceable rear leg from Sofa and providing new first class teak wood leg size 70mm x 35 mm x 495mm, rest all as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable Arm rest from Sofa and providing new first class teak wood Arm Rest of size 35mm x 70mm x 725mm, rest all as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable side rail from Sofa and providing new first class teak wood side rail of size 35 mm x 100mm x 585mm, rest all as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable bearer from Sofa and providing new first class teak wood bearer of size 40mm x 40mm x 725mm, rest all as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable battens from Sofa and providing new first class teak wood battens of size 50mm x 20 mm, rest all as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable front rail from Sofa three seater and providing new first class teak wood front rail of size 35mmx 100mm x 1590 mm, rest all as shown on drg and as directed by Engr-in-Charge.

Removing existing unserviceable front rail from Sofa single seater and providing new first class teak wood front rail of size 35mm x 10mm x 530 mm, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE DRESSING GENTS/MIRROR DRESSING GENTS FD-230/FD-379 or similar in MAP

Replacement of existing unserviceable drawer for Table dressing gents made out of prelaminated particles board 12mm thick one side teak facing and balancing white on the other side and 12x12mm wooden beading around all as specified on drawing or as directed by Engineer-in-charge. (Note-Each drawer should be measured as single unit)

S & Fixed in repairs new mirror 5mm thick of approved make with full frame all as specified on drawing or as directed by Engineer-in-charge.

S & Fixed in repairs new top made out of 18 mm thick pre laminated particle borad of approved make, all as specified on drawing or as directed by Engineer-in-charge.

TABLE DRESSING LADIES FD-251/FD-378 or similar in MAP

S & Fixed in repairs table top of Table dressing ladies with 18 mm thick pre-laminated particle Board of approved make, all as specified on drawing or as directed by Engineer-in-charge.

S&Fixed in repairs new Glass shutters of Table dressing ladies all as specified on drawing or as directed by Engineer-in-charge. (Each glass shutter shall be measured as single unit)

Removing the existing unserviceable Aluminium channel and S & Fixed in repairs Aluminium Channel all as specified on drawing or as directed by Engineer-in-charge.

S & Fixed in repairs new back support made out of 6 mm thick plywood for mirror of Table dressing ladies all as specified on drawing or as directed by Engineer-in-charge.

S & Fixed in repairs new mirror 5 mm thick for Table dressing ladies of approved make with complete frame back all as specified on drawing or as directed by Engineer-in-charge.

Table Bed Side FD-210/248/FD-276

Removing of existing unserviceable sides of Table Bed Side and providing new sides of 18mm thick prelaminated particle Board with teak wood colour finishing one side and balancing white on the other side of exterior grade and 18 x 6 mm teak wood beading on front sides, rest all as specified on drawing or as directed by Engineer-in-charge. (Each sides will be measure as single unit)

Removing of existing unserviceable Top and bottom of Table Bed Side and providing new Top of 18mm thick prelaminated particle Board with teak wood colour finishing one side and balancing white on the other side of exterior grade and 18 x 6 mm teak wood beading on front sides, rest all as shown on drg and as directed by Engr-in-Charge. (Each Top & Bottom will be measure as single unit)

Removing of existing unserviceable Back of Table Bed Side and providing new Back of 6mm plywood commercial shall be fixed with headless nail, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable shelf of Table Bed Side and providing new shelf of 12mm thick prelaminated particle Board with teak wood colour finishing one side and balancing white on the other side of exterior grade and 12 x 6 mm teak wood beading on front sides, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable/broken PVC Shoes, M & L for fixing of PVC shoes superior quality of 20mm dia with suitable screw at the bottom of the leg in the following furniture items as specified & directed by Engr-in-charge:- Chair Dining, Chair Writing, Chair easy, Chair Wooden bottom without arms,Table Bed Side,Stool Dressing CB,Table centre,Teapoy, Table Peg & Table 3'x2' with/without drawer

Supply & fixing of Knob of aluminium anodized dark brown in shade as approved by GE & in the following furniture items with screws as specified & as directed by Engr-in-Charge:- Table Dressing Gents/Ladies, Side Board, Table 3'x2' with drawer, Table Writing, Book case.

SIDE BOARD (1220mm x 455mm x 760mm) FD-241 or similar

Removing the existing unserviceable top of side board and providing new top made out of 18mm thick prelaminated particle board exterior grade of size 1220 x 455 mm all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable sides of side board and providing new sides made out of 18mm thick prelaminated particle board exterior grade of size 650x450mm all as specified on drawing or as directed by Engineer-in-charge. (Note : Each side will be measured as single unit)

(c) Removing he existing unserviceable back of Side Board and providing new Back with 6mm thick plywood commercial type of Size 650 x 1220 mm all as specified on drawing or as directed by Engineer-in-charge.

(d) Removing the existing unserviceable Top drawer and providing New drawer made out of 12 mm thick particle board having ply on both sides. The drawer shall be run as 19 mm x 19 mm thick teak wood batten all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable Drawers (other than Top drawers) and providing new drawer made out of 12mm thick particle board having ply on both sides. The drawer shall be run as 19mm x 19mm thick teak wood bearer all as specified on drawing all or as directed by Engineer-in-charge. (Note : Each drawer will be measured as single unit)

Removing the existing unserviceable shutter and providing new shutter made out of 18mm thick prelaminated particle board (Novapan) of size 400x600 mm including Hinges and lock all as specified on drawing or as directed by Engineer-in-charge. (Note : Each shutter will be measured as single unit)

Removing the existing unserviceable bottom of side board and providing new bottom of size 1220 x 455 mm made out of 18mm thick plywood commercial type all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable leg frame of side board and providing Teak wood 2nd class hard wood leg frame all as specified on drawing or as directed by Engineer-in-charge.

Removing the existing unserviceable broken legs of side board and providing new Teak wood leg 2nd class hard wood of size 45 x 45 x 125 mm but at bottom 25 x 25 mm all as specified on drawing or as directed by Engineer-in-charge.(Note : Each leg will be measured as single unit.)

Replacement of unserviceable hinges 75mm long piano type.

S & Fixed in repairs locking device 1st quality brass 6 lever locks iron body with duplicate keys chromium plated all as specified on drawing or as directed by Engineer-in-charge.

(Note :- All parts as mentioned above includes 3mm thick Teak wood edging should be polish wherever applied necessary as per drawing).

TEAPOY WOODEN FD-232/FD-278/FD-382

Replacement of existing unserviceable top for Teapoy made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from teapoy made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (both short & long) from teapoy made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE DINING 8/6/4 PERSONS FD-239/FD-273 or similar

S&F in repairs to unserviceable damaged legs from Table dining 8/6/4 persons made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table dining 8/6/4 persons made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front/back long rails from Table dining 8 persons made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Replacement of existing unserviceable table top for Table dining 8 persons made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and as directed by Engineer-in-charge.

Replacement of existing unserviceable table top for Table dining 6 persons made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged front/back long rails from Table dining 6 persons made out of hard wood (Teak) , rest all as shown on drg and as directed by Engr-in-Charge.

Replacement of existing unserviceable table top for Table dining 4 persons made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged front/back long rails from Table dining 4 persons made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Common for Table dining 8/6/4 persons

S&F in repairs Triangular wooden bracket 100X100X20mm thick hard wood (Teak) for all types of tables between leg & stiffners for extra strength complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE WRITING FD-249/FD-275 or similar

Replacement of existing unserviceable table top for Table writing made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and as directed by Engineer-in-charge.

S&F in repairs replacement of unserviceable damaged legs from Table writing with new leg made out of hard wood (Teak) rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs replacement of unserviceable damaged foot rest from Table writing with new foot made out of hard wood (Teak) rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs replacement of unserviceable damaged stiffner from Table writing with new stiffner made out of hard wood (Teak) rest all as shown on drg and as directed by Engr-in-Charge.

Sides of cabinet with 18mm thick pre-laminated particle board as per drg

18mm thick prelaminated particle board Cabiner door along with locking arrangement and handles as per drg

TABLE CENTRE/TABLE CENTRE 2 TIER FD-235/FD-274

Replacement of existing unserviceable table top for Table centre made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from Table centre made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged top rail (long side) from table centre made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom rail (short side) from table centre made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE WITH DRAWER 900x 600 x 760mm FD-224/FD-283

Removing of existing unserviceable table top for Table with drawer 900 x 600 x 760mm and providing new table top made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from Table with drawer 900x600x760mm made out of hard wood (Teak) size 60x30x740mm rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table without drawer 900x600x760mm made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged long rails from Table with drawer 900x600x760mm made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (short side) from Table with drawer 900x600x760mm made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged drawers from Table with drawer 900x600x760mm made out of hard wood (Teak) including providing 6mm thk commercial ply to bottom of drawer complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE WITHOUT DRAWER 900x 600 x 760mm/TABLE ONE PCS FD-223/FD-231/FD-284

Removing of existing unserviceable table top for Table without drawer 900 x 600 x 760mm/table one piece and providing new table top made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from Table without drawer 900x600x760mm made out of hard wood (Teak) size 60x30x740mm including applying two coats of French polish including preparation of surfaces complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged side short rails from Table without drawer 900x600x760mm made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front long rails from Table without drawer 900x600x760mm made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged bottom stiffners (short side) from Table without drawer 900x600x760mm made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

TABLE 900x 900 x 760mm FD-291

Removing of existing unserviceable table top for Table 900 x 900 x 760mm and providing new table top made out of 18mm thick exterior grade particle board (ISI marked) duly post formed (PFT) with 0.6mm thick laminates and 2mm thick edging on two sides (colour shade as approved by GE) of approved make all as shown on drawing and as directed by Engineer-in-charge.

S&F in repairs to unserviceable damaged legs from Table 900x900x760mm made out of hard wood (Teak) size 60x30x740mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

S&F in repairs to unserviceable damaged front/side rails from Table 900x900x760mm made out of hard wood (Teak) complete, rest all as shown on drg and as directed by Engr-in-Charge.

Table Bed Side FD-252/FD-282

Removing of existing unserviceable legs of stool dressing and providing with new legs of hard wood (Teak) of size 50 x 30 x 380mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable side rails of stool dressing and providing with new side rails of hard wood (Teak) of size 25 x 50 mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

Removing of existing unserviceable front and rear rails of stool dressing and providing with new front and back of hard wood (Teak) of size 25 x 65 mm complete, rest all as shown on drg and as directed by Engr-in-Charge.

Replacement of existing unserviceable plastice cane of Stool dressing and recanning the same with half round 2mm wide and 0.4mm thick plastic cane, rest all as shown on drg and as directed by Engr-in-Charge.

Hat Stand with mirror FD-233

S & Fixed in repairs new mirror 5 mm thick for Hat stand with mirror of approved make with complete frame back all as specified on drawing or as directed by Engineer-in-charge.

Removing of existing unserviceable Back of Hat stand with mirror and providing new Back of 6mm plywood commercial shall be fixed with headless nail, rest all as shown on drg and as directed by Engr-in-Charge.

S&F of brass pegs with brass screw in place of broken/ lost pegs in hat stand with mirror, rest all as shown on drg and as directed by Engr-in-Charge.

SOFA SET 5 SEATER CUSHIONED FULLY UPHOLSTERED (TP)

Removing the existing unserviceable tapestry cloth and foam cushion from sofa set fully upholstered completely, replacing with new foam cushion 40 density duly covered with new tapastry cloth including completly stiching, rest all as shown on drg and as directed by Engineer-in-Charge.

M&L preparation of old wood surfaces by scraping and filling bore holes with putty and finally rubbing with sand paper/ abbrasive cloth throughly for smooth and clean surface and applying two coat of french polish over a coat of mension wax polish till the smooth finishing complete all as specified on drawing or as directed by Engineer-in-charge. for the following furniture articles:-

Bed plywood top/Bed Newar/Cot ply top FD-246 or Similar

Bin Soiled Linen Small FD-244 or Similar

Book case small/open small FD-237 or Similar

Chair dining/Chair dining PVC Seat FD-228/279 or Similar

Chair dining Long baclk/Cushioned FD/E6/MAP/10 (R) or similar in MAP

Chair Easy FD-229 or Similar

Chair Writing FD-280 or Similar

Chair wooden bottom FD-225/285 or Similar

Hat Stand with mirror FD-233

Sofa Set 3 Pcs 5 Seater FD-281/373

Sofa Set 4 Seater FD-281/373

Stool dressing CB/Stool Dresing Cushioned FD-282 or Similar

Side board FD-241,FD-1112

Table dressing Gents with Mirror/Mirror Dressing Gents FD-230 or Similar in MAP

Table dressing Ladies with Mirror/Table Dressing Ladies with Stool FD-251

Table bed side FD-276 or Similar

Peg Table FD-277/FD-384 or Similar

Table with drawer 900 x 600 x 760mm FD- 283 or Similar

Table without drawer 900 x 600 x 760mm /Table one Pieces FD- 284 or Similar

Table 900X900x 760MM FD-291

Table dining 8/6/4 persons FD-273 or Similar in MAP

Teapoy wooden FD-278/382 or Similar

Table writing/Table writing Pedestal FD-275 or Similar

Table centre/Table Centre 2 tier FD-274 / 235 or Similar

Sch of Credit- Total contract sum shall be calculated after deduction of Sch of Credit amount Credit amount - 51437.50

Techno India Enterprises

M/S Parshant Associates

SMS Enterprises