Construction of State Of Art Office building and Campus based on GRIHA Green building ,Super ECBC and Net zero energy principles for Maharashtra Energy Development Agencey MEDA at Aundh Pune-7 (Balance work of Main building B plus G plus 3 floors, D.

Amount

Excavation for foundation in earth,soil of all types, sand ,gravel and soft murum ,including removing the excavated material up to a distance of 50 meter beyond the building area & stacking and spreading as directed,dewatering preparing the bed for the foundation and necessary back filling,ramming,watering including shoring and strutting etc.complete.(Lift upto 1.50 meter) By Mechanical Means.R.A.NO.1

Excavation for foundation in hard murum, including removing the excavated material up to a distance of 50 meter beyond the building area & stacking and spreading as directed,dewatering preparing the bed for the foundation and necessary back filling,ramming,watering including shoring and strutting etc.complete.For Lift upto 1.50 meter By Mechanical Means.R.A.NO.2

Excavation for foundation in hard murum, including removing the excavated material up to a distance of 50 meter beyond the building area & stacking and spreading as directed,dewatering preparing the bed for the foundation and necessary back filling,ramming,watering including shoring and strutting etc.complete.For Lift upto 1.50 meter By Mechanical Means.R.A.NO.2

Excavation for foundation in hard murum, including removing the excavated material up to a distance of 50 meter beyond the building area & stacking and spreading as directed,dewatering preparing the bed for the foundation and necessary back filling,ramming,watering including shoring and strutting etc.complete.For Lift from 1.50 meter to 3.0 meter By Mechanical Means.R.A.NO.3

Excavation for foundation in hard murum and boulders, including removing the excavated material up to a distance of 50 meter beyond the building area & stacking and spreading as directed,dewatering preparing the bed for the foundation and necessary back filling,ramming,watering including shoring and strutting etc.complete.(Lift upto 1.50 meter to 3.0 eter)By Mechanical Means.R.A.NO.4

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 metres beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth /murum, ramming, watering including shoring and strutting etc. complete (lift upto 1.5 m) by Mechanical Means.R.A.NO.5

Excavation for foundation in Soft rock and old cement or lime masonry foundations including removing the excavated material upto a distance of 50 meters beyond the building area and stacking as directed, including dewatering, preparing the bed for the foundation and necessary back filling with available earth/ murum, ramming, watering including shoring and strutting etc. complete. (Lift from 1.5 metre to 3.0 metre) by Mechanical Means.R.A.NO.5

Excavation for foundation in Hard-rock by blasting including trimming and leveling the bed by chiselling where necessary and removing the excavated material and stacking it in measurable heaps within a distance of 50 metres from the building area including dewatering and back filling with available earth/ murum watering, ramming etc. complete, (Lift from 1.5m To 3.0 m) by Mechanical Means.

Excavation for foundation in hard rock by chiselling ,wedging,line drilling etc. including trimming and levelling the bed removing the excavated material upto a distance of 50 meter, beyond the building area,stacking as directed, dewatering and back filling with available earth, murum, ramming, watering etc.complete. Lift 1.5 meter(SSR NO 21.20)R.A.NO.6

Dewatering on Break Horse Power basis by using water pump including diversion of stream, providing coffer dams, earthern bunds etc. as may be necessary for foundation and other parts of the the works and pumping out water during and after excavation as may be required. a) By using 3.0 Break Horse Power Pump. Note : Prior approval of Superintending Engineer will be necessary. Spec : BR 4 Page No 104.105(SSR NO 12.22)R.A.NO.7

Providing and Laying 4 mm Hydrostop plus PY APP Modified membrane plain finish of TIkidan India Limited or equivalent On the cleaned surface applying bituminous [email protected] L per sqm, the surface should be smooth free of undulation.. When the primer is dry lay 4mm Hydrostop plus bituminous membrane with torch on method. The membrane should be 3.6kgs/sqm in weight snd have a reinforcement of at least 160 gms of non woven polyster. The tesile strength of the membrane should be 800N/5cm (Longitudinal) and Elongation as 40% as per ASTM D-5147. The softening point of the membrane should be > 150deg C with a penetration point at 25 deg to be < 20+/-10dmm. The side laps and end laps should have an overlap of 3-4 inches and it should be thermofused together so that it forms a single sheet all throughout. For Vertical Surface Rate approved by circle office

Providing and Laying 4 mm Hydrostop plus PY APP Modified membrane plain finish of TIkidan India Limited or equivalent On the cleaned surface applying bituminous [email protected] L per Square Meter, the surface should be smooth free of undulation.. When the primer is dry lay 4mm Hydrostop plus bituminous membrane with torch on method. The membrane should be 3.6kgs/Square Meter in weight snd have a reinforcement of at least 160 gms of non woven polyster. The tesile strength of the membrane should be 800N/5cm (Longitudinal) and Elongation as 40% as per ASTM D-5147. The softening point of the membrane should be > 150deg C with a penetration point at 25 deg to be < 20+/-10dmm. The side laps and end laps should have an overlap of 3-4 inches and it should be thermofused together so that it forms a single sheet all throughout. For Vertical Surface Rate approved by circle office

Providing preconstructional antitermite treatment as per I.S. 6313 (Part-II) by treating the top surface of plinth filling at the rate of 5 litres of emulsion concentrate at 1.0 percent of clorophyrifos per square metre of surface area covering ten years guarantee on bond paper.

Conveying materials obtained from road cutting & watering and compaction to not less than 97% of standard proctor density for a lead of 50 to 300 m.R.A.NO.8

Providing dry/ trap/ granite/ quartzite/ gneiss rubble stone soling 15 centimeter to 20 centimeter thick including hand packing and compacting complete. Spec. No.: Bd.A. 12 Page No. 264R.A.NO.10

Supplying hard murum at the road site including conveying and stacking complete.

Spreading hard murum/ soft murum/ gravel or kankar for side width complete.

Compacting the hard murum side widths including laying in layers on each side with vibratory roller including artificial watering complete.

Construction of granular sub-base by Plant Mix Method by providing close graded Material,mixing in a mechanical mix plant at OMC,carriage of mixed Material to work site,spreading in uniform layers with Motor Grader/ Paver on prepared surface and compacting with vibratory power roller to achieve the desired density complete as per clause 401.For Grading I Material.

Providing, laying, spreading and compacting stone aggregates of specific sizes to water bound macadam specification including spreading in uniform thickness, hand packing to proper grade and camber, applying and brooming requisite type of screening/ binding Materials to fill up the interstices of coarse aggregate, watering and compacting with vibratory roller to the required density. By Mechanical Means Grading-I, using Screening Type-B (11.2 milimetre Aggregate).

Providing and applying primer coat with bitumen emulsion on prepared surface of Granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/Square Metre using mechanical means.

Providing and applying tack coat on the prepared surface heating by flames in boiler and spraying bitumen set footed in bitumen boiler on B.T. surface at 2.50 Kg per 10 Square Metre using VG-30 grade bulk bitumen.

Providing and applying tack coat on the prepared surface heating by flames in boiler and spraying bitumen with sprayer on concrete surface treated with primer at 3.25 Kg per 10 Square Metre, using VG-30 grade Bulk Bitumen .

Providing and constructing 75 mm. thick Modified Penetration Macadam (MPM) road surface including all materials, preparing the existing road surface, spreading 40 mm. stone metal layers 30% crusher broken metal + 70% Hand broken metal (by breaking rubble obtained by blasting) heating and spraying the bitumen of VG-30 grade @ 2 Kg/sqm, spreading 12 mm. size chips compacting with three wheel static roller having weight 8 to 10 MT. to achive the desired degree of compaction as per Technical Specification Clause 506 etc. complete including picking of existing WBM surface.

Providing and Laying Open Graded premix surfacing 20 milimetre thickness composed of 13.2 milimetre to 5.6 milimetre aggregates premixed with bituminous binder transported to site with Vehicle Tracking System, laid over a previously prepared surface, finished to the required grade, level, alignment and rolling to achieve the desired compaction, using VG-30 bulk bitumen, Drum Mix type hot mix plant with Superwisery Control and Data Acquisition, Paver and Vibratory roller over Modified Penetration Macadam surface.

Providing and laying of Type-A 9 milimetre thick premix seal coat with HMP of apropriate capacity, crushed stone chiping 6.7 mm size and penetration of VG-30 bulk bitumen at the rate of 1.2 kilogram per square metre, preparing existing road surface by mechanical means, spreading chips and rolling, by static roller having weight 8 to 10 M.T. etc. complete.

Filling in plinth and floors with approved excavated materials in 15 cm to 20 cm layers including watering and compaction complete. Spec. No.: Bd.A.10 Page No. 262R.A.NO.711

Filling in plinth and floors with contractors material/brought from outside and approved by Engineer incharge in layers of 15 cm to 20 cm including watering and compaction etc. complete.

Providing and laying Cast in situ/Ready Mix cement concrete in M-10 of trap/ granite/ quartzite/ gneiss metal for foundation and bedding including bailing out water, Steel centering, formwork, laying/pumping, compacting, roughening them if special finish is to be provided, finishing if required and curing complete, with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) R.A.NO.11

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. work in foundations like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. columns as per detailed designs and drawing or as directed including Steel centering formwork, cover blocks laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) R.A.NO.12

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including steel centering, formwork,cover blocks, laying/pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete,(Excluding reinforcement and structural steel). with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc) R.A.NO.13

Fourth Floor R.A.NO.17

Fifth Floor R.A.NO.18

Sixth Floor R.A.NO.19

Seventh Floor R.A.NO.19A

Providing and laying cast in situ/ Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. columns as per detailed designs and drawing or as directed including centering, formwork, cover blocks, laying/ pumping, compaction finishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Reversible Drum Type mixer/ concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand V.S.I. Grade finely washed etc.)R.A.NO.700

Providing and laying Cast in situ/Ready Mix cement concrete M-30 of trap / granite /quartzite/ gneiss metal for R.C.C. beams and lintels as per detailed designs and drawings or as directed including steel centering, formwork, cover blocks, laying/pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSI Grade finely washed etc)Ground Floor R.A.No.20

First Floor R.A.No.21

Second FloorR.A.NO.22

FourthFloor R.A.NO.24

Fifth Floor R.A.NO.25

Sixth Floor R.A.NO.26

Seventh Floor R.A.NO.26a

Providing and laying Cast in situ/Ready Mix cement concrete in M-30 of trap / quartzite /granite /gneiss metal for R.C.C. Waist slab, and steps of staircases as per detailed design and drawings or as directed including steel centering, formwork, steel props, laying/pumping, compaction, finishing uneven and honeycombed surface with C.M. 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening the surface if special finish is to be provided and curing etc. complete. (Excluding einforcement, including cover block).(Newly laid concrete shall be covered by gunny bag, plastic, tarpaulin etc.) with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand / Crushed sand VSIGrade finely washed etc) Fourth floor R.A.No.659

Fifth Floor R.A.No.660

Sixth Floor R.A.No.661

Seventh Floor R.A.No.662

Providing and laying Cast in situ/ Ready Mix cement concrete M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Slabs and Landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/ pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Reversible Drum Type mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand V.S.I. Grade finely washed etc.) Ground FloorR.A.No.702

Providing and laying Cast in situ/ Ready Mix cement concrete Mix-30 of trap/ granite/ quartzite/ gneiss metal for Reinforced Cement Concrete Slabs and Landings as per detailed designs and drawings including centering, formwork, cover blocks, laying/ pumping, compactionfinishing the formed surfaces with cement mortar 1:3 of sufficient minimum thickness to give a smooth and even surface or roughening if special finish is to be provided and curing etc. complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based Programmable Logic Controller with Superwisery Control and Data Acquisitionenabled Reversible Drum Type mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand V.S.I. Grade finely washed etc.) Ground floor R.A.NO.27

Fourth Floor R.A.NO.31

Fifth Floor R.A.NO.32.

Sixth Floor R.A.NO.33

Seventh Floor R.A.NO.33a

Providing and laying Cast in situ/ Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C. Pardi of required thickness including centering, formwork, cover blocks, laying/ pumping, compacting, curing, finishing and rougheningthem if special finish is to be provided and curing complete, (Excluding reinforcement and structural steel) with fully automatic micro processor based PLC with SCADA enabled Reversible Drum Type mixer/ concrete Batch Mix plant (Pan mixer) etc. complete, with fine aggregate (Natural Sand/ Crushed Sand V.S.I. Grade finely washed etc.)

Providing and laying Cast in situ/ Ready Mix cement concrete in M-30 of trap/granite/quartzite/gneiss metal for R.C.C. pardi of required thickness including steel centering, formwork, coverblocks, laying pumping, compacting and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structura lsteel). with fully automatic microprocess or based PLC with SCAD AenabledreversibleDrumTypemixer/concreteBatchmixplant(Panmixer)etc.complete.Withfineaggregate(Crushedsand VSI Grade)R.A.No.652

Fourth Floor R.A.No.656

Fifth Floor R.A.No.657

Sixth Floor R.A.No.658

Seventh Floor R.A.No.658A

Providing and laying in situ cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in founda-tions like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, cover blocks compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) complete, with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant (pan mixer) With Natural Sand Spec. No.: Bd.F.3 Page No. 298 and B.7, Page No.38R.A.No.699

Providing and laying in situ cement concrete M-20 of trap / granite /quartzite/ gneiss metal for R.C.C. work in founda-tions like raft, strip foundations, grillage and footings of R.C.C. columns and steel stanchions etc. including bailing out water, formwork, cover blocks compaction and curing roughening the surface if special finish is to be provided (Excluding reinforcement and structural steel) complete, with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant (pan mixer) With Natural Sand Spec. No.: Bd.F.3 Page No. 298 and B.7, Page No.38R.A.No.699

Providing and laying Cast in situ/ Ready Mix cement concrete M-20 of trap/ granite/quartzite/ gneiss metal for R.C.C. Beams and Lintels as per detailed designs and drawings or as directed including centering, formwork, cover blocks, laying/ pumping, compactionand roughening the surface if special finish is to be provided and curing etc. complete. (Excluding reinforcement and structural steel), with fully automatic micro processor based PLC with SCADA enabled Reversible Drum Type mixer/ concrete Batch Mix plant (Pan mixer) etc. complete with fine aggregate (Natural Sand/ Crushed Sand V.S.I. Grade finely washed etc.)R.A.No.701

Providing & casting in situ cement concrete M-30 of trap/ granite/ quartzite/ gneiss metal for R.C.C. chajja as per detailed design & drawings including centering, formwork, cover blocks compacting & roughening the surface if special finish is to be provided & curing complete. (Excluding reinforcement).with fully automatic micro processor based PLC with SCADA enabled concrete batch mix plant (pan mixer).... With natural sand. Spec. No.: Bd.F.9 Page No. 303 and B.7, Page No.38 Fourth FloorR.A.No.667

Fifth Floor R.A.No.668

Sixth Floor R.A.No.669

Seventh Floor R.A.No.670

Providing and laying Cast in situ/Ready Mix cement concrete in M-20 of trap/ granite/ quartzite/ gneiss metal for R.C.C.coping to plinth or parapet and sill of doors and windows moulded as per detailed drawings or chamfered as approved by the Engineer including steel centering, formwork, cover blocks, laying/pumping, compacting , curing , finishing and roughening them if special finish is to be provided and curing complete. (Excluding reinforcement and structural steel).with fully automatic micro processor based PLC with SCADA enabled reversible Drum Type mixer/ concrete Batch mix plant (Pan mixer) etc. complete. With fine aggregate (Natural Sand /Crushed sand VSI Grade finely washed etc) Ground Floor R.A.No.578

Seventh Floor R.A.No.579

Providing and casting in situ or precast tapering R.C.C. M-20 Barrier type Kerb with gutter (as per IRC:86-1983) embedded 125 mm below ground level over M-10 P.C.C. finished neatly with C.M. 1:2, setting the same in C.M. 1:2, including the required excavation in any strata and removing the excavated stuff any where in city and redoing the surface as specified and directed by Engineering In-charge. Using Concrete Batching and Mixing Plant.

Providing and fixing in position Thermo Mechanically Treated -FE -500 reinforcement of various diameters for Reinforced Cement Concrete pile caps, footings, foundations, slabs, beams, columns, canopies, staircase, newels, chajjas, lintels, pardis, copings, fins, arches, etc. as per detailed designs, drawings and schedules including cutting, bending, hooking the bars, binding with wires or tack welding and supporting as required complete.(SSR NO 26.33)Ground Floor R.A.NO.48

First Floor R.A.NO.49

Fourth Floor R.A.NO.52

Fifth Floor R.A.NO.53

Sixth Floor R.A.NO.54

Seventh Floor R.A.NO.54a

Providing and fabricating structural steel work in rolled sections like joists, channels, angles, tees etc. as per detailed design and drawings or as directed including cutting, fabricating, hoisting, erecting, fixing in position making riveted /bolted / welded connections without connecting plates, braces etc. and including one coat of anticorrosive paint and over it two coats of oil painting of approved quality and shade etc. complete.

Providing, fabricating and erecting at site of work the tubular steel structure (shed) as per standard design and specifications inclusive of one coat of anticorrosive paint and two coats of oil painting of approved quality and shade etc. complete.Ground Floor R.A.No.644

First Floor R.A.No.645

Second floor R.A.No.646

Third floor R.A.No.647

Fourth floorR.A.No.648

Fifth floor R.A.No.649

Sixth floorR.A.No.650

Seventh foorR.A.No.651

Providing Autoclaved Aerated Concrete Block masonary of Ecolite or equivalent make conforming to Indian Standard:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in superstructure including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to Indian Standard:6441 (Part I) - 1972) Spec : As directed by engineer in chargeGround Floor R.A.No.63

First Floor R.A.No.64

Fourth Floor R.A.NO.67

Fifth Floor R.A.NO.68

Sixth Floor R.A.NO.69

Seventh Floor R.A.NO.69a

Providing Autoclaved Aerated Concrete Block masonary of Ecolite or equivalent make conforming to Indian Standard:2185 (Part 3) - 1984 in extra fine jointing mortar of fixoblock of UltraTech or equivalent in Half brick thick wall including striking joints, raking out joints and scaffolding etc. Complete. (The test shall be carried out conforming to Indian Standard:6441 (Part I) - 1972) Spec : As directed by engineer in charge Ground Floor R.A.No.70

First Floor R.A.No.71

Fourth Floor R.A.NO.74

Fifth Floor R.A.NO.75

Sixth Floor R.A.NO.76

Seventh Floor R.A.NO.76a

Providing fly ash brick masonary with conventional / I.S. type fly ash bricks in cement mortar 1:6 in foundation and plinth including bailing out water manually, striking joints, racking out joints, watering and scaffolding complete.

Providing fly ash brick masonary with conventional / Indian Standard type fly ash brick in cement mortar 1:6 including striking joints, racking out joints watering and scaffolding complete.b) for superstructure Ground Floor R.A.NO.77 First Floor Second Floor R.A.NO.79 Third Floor R.A.NO.80

Fourth Floor R.A.NO.81

Fifth Floor R.A.NO.82

Sixth Floor R.A.NO.83

Seventh Floor R.A.NO.83a

Providing Second class fly ash brick masonry with conventional /25 millimeter x 1.60 millimeter Indian Standard type bricks in cement mortar 1:4 in half brick thick wall including mild steel longitudinal reinforcement of two bars of 6 millimeter diameter/ two hoop iron strips 25 millimeter x 1.60 millimeter at every third course, properly bent and bounded at ends scaffolding raking joints and watering etc. complete.Fourth Floor R.A.No.88

Fifth Floor R.A.No.89

Sixth Floor R.A.No.90

Seventh Floor R.A.NO.90a

Providing & constructing non load bearing wall with 200millimeter Porotherm horizontally perforated THERMO BLOCK with compressive strength not less than 35 kilo gram per square centimeter, U value of 0.60 W/m2K, water absorption of 15%, masonary to be done using sand cement mortar of 1:6 with blocks of size 400millimeter x 200millimeter x 200millimeter (12.5 bricks per Square Meter excluding mortar joint thickness) including cost of materials, labour charges, scaffolding, curing at all heights, complete as per specifications & directions of Engineer In Charge. Cost shall be inclusive of filling the blocks with cement mortar at exposed junctions and filling with concrete using 12millimeter downsize aggregates at windows and door jambs for fixing hold fast, anchors etc. It must have green buiding certifications from Green Rating for Integrated Habitat Assessment/Indian Green Building Council and it should comply to Indian Standard 3952. The rate shall be inclusive of all labour, material, scaffolding, transportation, taxes, including all leads, lifts at all levels and shall be as directed by Engineer in charge.Ground Floor R.A.No.481

First Floor R.A.No.482

Second Floor R.A.No.483

Third Floor R.A.No.484

Fourth Floor R.A.No.485

Fifth Floor R.A.No.486

Sixth Floor R.A.No.487

Seventh Floor R.A.No.487a

Providing and applying Two coats of wall care Putty on plastered surface and Ceiling and Walls to prepare surface even and smooth of approved make, etc complete. Ground Floor R.A.No.488

First Floor R.A.No.489

Second Floor R.A.No.490

Third Floor R.A.No.491

Fourth Floor R.A.No.492

Fifth Floor R.A.No.493

Sixth Floor R.A.No.494

Seventh Floor R.A.No.495

Providing & fixing chicken mesh jali (22 gauge) at the junction of two different surface of different material compent at the time of plastering to prevent cracking of plaster surface as & when directed at all floors with all leads & lifts etc. complete.(SSR NO 32.26)Ground Floor R.A.No.98

First Floor R.A.No.99

Second Floor R.A.No.100

Third Floor R.A.No.101

Fourth Floor R.A.No.102

Fifth Floor R.A.No.103

Sixth Floor R.A.No.104

Seventh Floor R.A.No.104a

Providing and laying handcut polished Kotah Stone flooring 25 milimetre to 30 milimetre thick and 45 centimetre to 55 centimetre wide in plain/ diamond pattern on a bed of 1:6 cement mortar including cement float, filling joints with neat cement slurry, curing, polishing and cleaning etc. complete.

Providing and laying 18 milimetre thick ADONI BROWN LEATHER FINISH stone for flooring, machine cut in required size, approved shade, color and texture laid using white cement slurry over 20 milimetre (average) thick base of cement mortar 1:4 followed by laying, fixing and jointed with white cement slurry mixed with matching pigment, including rubbing and curing moulding and polishing to edge to give high gloss finish etc complete. The application rate for tile adhesives shall be as per manufacturer's reco milimetre endations. as per detail drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels and as directed by Engineer in charge. Complete. a) Flooring Ground Floor R.A.No.563

First Floor R.A.No.564

Second Floor R.A.No.565

Third Floor R.A.No.566

Fourth Floor R.A.No.567

Fifth Floor R.A.No.568

Sixth Floor R.A.No.569

Seventh Floor R.A.No.569a

Providing and laying 18 milimetre thick ADONI BROWN LEATHER FINISH stone for flooring, machine cut in required size, approved shade, color and texture laid using white cement slurry over 20 milimetre (average) thick base of cement mortar 1:4 followed by laying, fixing and jointed with white cement slurry mixed with matching pigment, including rubbing and curing moulding and polishing to edge to give high gloss finish etc complete. The application rate for tile adhesives shall be as per manufacturer's reco milimetre endations. as per detail drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels and as directed by Engineer in charge. Complete. a) Skirting Ground Floor R.A.No.570

First Floor R.A.No.571

Second Floor R.A.No.572

Third Floor R.A.No.573

Fourth Floor R.A.No.574

Fifth Floor R.A.No.575

Sixth Floor R.A.No.576

Seventh Floor R.A.No.569a

Providing and laying RAK /NITCO/KAJARIA make Vitirified full body/ double charged special tiles of premium quality & color and size 600 millimeter x 600 millimeter of 8-10 millimeter thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning complete.(Note: Water absorption should not be more than 0.05%) flooring as directed by Engineer in charge. Complete. The rate shall be inclusive of all leads & lifts at all levels and wastages.R.A.NO.1005

Providing and laying RAK /NITCO/KAJARIA make Vitirified double charged vitrified mirror/gloss/matt/rustic matt/stone finish premium quality tile of any colour from NITCO/RAK/Kajaria of size 590 to 605 millimetre x 590 to 605 millimetre of 8 to 10 millimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning complete.(Note: Water absorption should not be more than 0.05%) Skirting as directed by Engineer in charge. Complete. The rate shall be inclusive of all leads & lifts at all levels and wastages.R.A.NO.1006

Seventh Floor R.A.No.519

Providing and laying Antiskid Ceramic tiles of approved quality of company Kajaria /Nitco /Asian or equivalent make of size 30 centimeter x 30 centimeter and conforming to Indian Standard 15622-2006 (Group-B IIA) for antiskid flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing complete. Ground Floor R.A.NO.105

First Floor R.A.NO.106

Second Floor R.A.NO.107

Third Floor R.A.NO.108

Fourth Floor R.A.NO.109

Fifth Floor R.A.NO.109a

Sixth Floor R.A.NO.109b

Seventh Floor R.A.NO.109c

Providing and laying ceramic tiles having size 30 cm. x 60 cm. confirming to corresponding I.S. for dado and skirting in required position with readymade adhesive mortar of approved quality on plaster of 1:2 cement mortar including joint filling with white/ colour cement slurry cleaning curing etc. complete.Ground Floor R.A.No.119

First Floor R.A.No.120

Second Floor R.A.No.121

Third Floor R.A.No.122

Fourth Floor R.A.No.123

Fifth Floor R.A.No.124

Sixth Floor R.A.No.125

Seventh Floor R.A.No.125a

Providing and laying vitrified matt finish decorative type tiles etc. complete for Flooring.R.A.No.126

Providing and laying vitrified mirror / glossy finish decorative type tiles on a bed of 1:4 cement mortar etc complete for Skirting.R.A.No.133

Providing and laying Pergo Engineered 14 millimeter wood parquet vivid Walnut 3 strip W 1911-03042 .Top Layer -3 millimter with base core of Spruce or pine tiles for flooring, machine cut in required size, approved shade, color and texture laid using white cement slurry over 20 millimeter (average) thick base of cement mortar 1:6 followed by laying, fixing and jointed with white cement slurry mixed with matching pigment, including rubbing and curing moulding and polishing to edge to give high gloss finish etc complete. Including providing and fixing of ceramic tile base.The application rate for tile adhesives shall be as per manufacturer's recommendations. as per detail drawing.including all labour, material, scaffolding, transportation, including all leads, lifts at all levels but excluding goods and service tax Providing and laying RAK /NITCO/KAJARIA make Vitirified full body vitrified mirror/gloss/matt/rustic matt/stone finish premium quality tile of any colour from NITCO/RAK/Kajaria of size 590 to 605 millimetre x 590 to 605 millimetre of 8 to 10 millimetre thickness and confirming Indian Standard 15622-2006 (Group Bla) of approved make, shade and pattern for flooring in required position laid on a bed of 1:4 cement morar including neat cement float, filling joints, curing and cleaning complete.(Note: Water absorption should not be more than 0.05%) flooring as directed by Engineer in charge. Complete. The rate shall be inclusive of all leads & lifts at all levels and wastages. as directed by Engineer in charge.etc. complete..including all labour, material, scaffolding, transportation, taxes, including all leads, lifts at all levels and as directed by Engineer in charge. Complete. Sixth Floor Old Approved RA 1026

Supply & Installation of PERGO make Veneered Skirting for wall and Veneered 5in1 Door Profile for Door Junctions. Skirting size 16millimeter thk and height 80 millimeter ;Profile thickness 16millimeter and width 54 millimeter, including providing and fixing of ceramic tile base. The application rate for tile adhesives shall be as per manufacturer's recommendations. as per detail drawing.including all labour, material, scaffolding, transportation, taxes, including all leads, lifts at all levels and as directed by Engineer in charge.etc. complete..including all labour, material, scaffolding, transportation, including all leads, lifts at all levels but excluding goods and service tax and as directed by Engineer in charge. Complete. Sixth Floor Old Approved RA 1019

Providing and fixing machine cut machine polished 18 mm to 20 mm thick telephone black / Amba White / Cat bary brown / RBI red /Ocean Brown granite stone for treads and risers of steps and staircases of approved colour and shade with full moulding and three grooved line for the treads on bed of 1:4 Cement mortar including float filling joints with neat cement slurry curing polishing and cleaning etc. complete.Ground Floor R.A.NO.140

First Floor R.A.NO.141

Second Floor R.A.NO.142

Third Floor R.A.NO.143

Fourth Floor R.A.NO.144

Fifth Floor R.A.NO.145

Sixth Floor R.A.NO.146

Seventh Floor R.A.No.146a

Providing leather finished polishing to Granite Stone slab by continuous grinding in 4 coats of different bits to receive rough and matty finish including buffing process before laying and fixing of stone as per drawing and design, including cleaning, washing and finishing etc. complete.** Spec. No.: As directed by Engineer in charge (SSR NO 33.56)Ground Floor R.A.No.147

First Floor R.A.No.148

Second Floor R.A.No.149

Third Floor R.A.No.150

Fourth Floor R.A.No.151

Fifth Floor R.A.NO.152

Sixth Floor R.A.NO.153

Seventh Floor R.A.NO.153a

Providing and errecting chain link fencing 1.6 metre height with galvanised iron chain link of size 50 x 50 milimetre 8 guage thick and fixed 75 milimetre above Ground level on vertical Mild Steel Angle of 40x40x6 milimetre size including excavating pits for foundation and embeded in cement concrete block of 1:4:8 mix of size 450x450x670 milimetre at 1.75 metre center to center with iron bar 16 milimetre diameter as hold fast including welding link with angle frame at 30 cm. c/c nuts and bolts and horizontal Mild Steel Angles at top and bottom of 25x25x5 metre size and vertical Mild Steel flat 35 x 5 metre and 25 x 5 metre horizontal including cross support of 40x40x6 metre Angles both sides at every corner or bends embeded in concrete blocks of 1:4:8 of size 450x450x670 milimetre including 3 coats of oil painting etc. complete.

External Paint Providing and applying two coats of High Albedo paint having minimum Solar Reflective Index (SRI) 108 (with solar reflectance & thermal emittance tested as per ASTM) C 1549 and ASTM C 1371 respectively, VOC less than 10 cc/gm. The coating thickness and the methodology of application shall strctly as per manufacturer's specifitions and as approved by engineer in charge. Surface preparation includes cleaning with metal wire brush to remove all dust, fungus etc, washing with water all complete.The contractor shall give guarantee for the performance of SRI and also the durabitity of coating, all complete as per direction of Engineer - in- incharge.Ground Floor R.A.NO.504

First Floor R.A.NO.505

Second Floor R.A.NO.506

Third Floor R.A.NO.507

Fourth Floor R.A.NO.508

Fifth Floor R.A.NO.509

Sixth Floor R.A.NO.510

Seventh Floor R.A.No.510a

Internal Paint Providing and applying 2 coats of 100% Pure acrylic low VOC and APEO & HCHO free water based paint of approved colour that belongs to class 1 flame spread resistance of approved make Paint should provide durable and long lasting silk finish with a high crack tolerance of upto 1mm. Paint should have an oustanding washability with high resistance to wide range of bacteria and fungus. Paint has to be applied on smooth and uniform surface prepared by an acrylic copolymer low VOC & Odour putty. This surface should be primed with water based low VOC Primer. The work activity should cover all aspects of applying paints from surface preparation as directed by Engineer in charge Ground Floor R.A.NO.497

First Floor R.A.NO.498

Second Floor R.A.NO.499

Third Floor R.A.NO.500

Fourth Floor R.A.NO.501

Fifth Floor R.A.NO.502

Sixth Floor R.A.NO.503

Seventh Floor R.A.No.503a

Texture Paint Providing and applying two coats of texture dsynthetic paint of approved shade and quality and one coa tof primer before applying textured paint including scaffolding if necessary preparing surface by thoroughly cleaning oil,grease,dirtando the rmaterials as required,etc.complete.Ground Floor R.A.No.581

First Floor R.A.No.582

Second Floor R.A.No.583

Third Floor R.A.No.584

Fourth Floor R.A.No.585

Fifth Floor R.A.No.586

Sixth Floor R.A.No.587

Seventh Floor R.A.No.587a

Providing and Laying factory made coloured chamfered edge Cement concrete grass paver blocks of required strength,thickness & size/shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50 milimetre thick compacted bed of fine fine aggregate (natural sand/crushed sand VSI grade finely washed etc.), compacting and proper embedding/laying of inter locking paver blocks into the fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) bedding layer through vibratory compaction by using plate vibrator, filling the joints with fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and cutting of paver blocks as per required size and pattern, finishing and sweeping extra fine aggregate (natural sand/crushed sand VSI grade finely washed etc.) and complete as per manufacturer spsecifications & direction of Engineer-in-Charge. 60 milimetre thick CC paver block of M-35 grade concrete with approved colour and design & pattern.

Providing and preparing kitchen otta made up from 30 millimeter thick and 75 centimeter wide one side polished kadappa top 75 centimeter high vertical support for kadappa at 1 meter centre to center of 25 millimeter thick both side polished kadappa middle shelf and bottom of 20 millimeter thick one side polished kadappa with facia patti of 20 x 50 millimeter kadappa including all material labour cutting fixing with cement mortar and araldite curing polished and cleaning complete.Ground Floor R.A.No.154

First Floor R.A.No.155

Second Floor R.A.NO.156

Third Floor R.A.NO.157

Fourth Floor R.A.NO.158

Fifth Floor R.A.NO.159

Sixth Floor R.A.NO.160

Providing and fixing machine cut mirror polished on one side 18 millimeter to 20 millimeter thick telephone black /Amba White/Cadbary Brown/RBI Red/Ocean Brown granite stone partition with rounding the edges etc. complete.Ground Floor R.A.No.161

First Floor R.A.No.162

Second Floor R.A.NO.163

Third Floor R.A.NO.164

Fourth Floor R.A.NO.165

Fifth Floor R.A.NO.166

Sixth Floor R.A.NO.167

Providing and applying two coats of water proof cement paint of approved manufacture and of approved colour to the plastered surfaces including scaffolding if necessary, cleaning and preparing the surface,watering for two days complete.Seventh Floor R.A.No.588

Fire Door 55mm 2HR FRL (120/120) 3 Criteria - INTEGRITY / INSULATION/ Providing of 120 min Fire rated doors system duly tested for 3 criteria - Integrity, Insulation and Stability Criteria as per the IS: 3614 Part 2 and BS: 476 part 22 at National Test House, Govt of India laborator and/or with Central Building Research Institute, Govt of India undertaking with standard heating conditions as specified in IS:3614 Part II 1992 and BS:476 part 20 & 22 1987 to achieve the required integrity, insulation and stability (i.e. to restrict the heat radiation, temperature rise on the non fire side to the maximum of 140° C above the ambient temperature on the exposed surface of the shutter. The fire doors are tested with NCBN technology ("Non Combustible by Nature").. a) Door Frame: Supplying & Fixing frames for Fire resistant door shutters 1st class Malaysian Hardwood Frame densified (810 Kilogram/cum) and pressure treated with fire retardant chemicals in vacuum impregnation vessel under 160 psi pressure as per IS:401and kiln seasoned to moisture below 15% as per IS:1141 of section 120 X 70 mm spray quoted with 2 coats of intumescent paint of minimum 200 micron, with single row of Brush- Type ASTROFLAME intumescent strip of size 10mm x 4mm affixed in the slit of the Frame for fire and smoke sealing, etc. complete.Ground Floor R.A.No.590

First Floor R.A.No.591

Second Floor R.A.No.592

Third floor R.A.No.593

Fouth Floor R.A.No.594

Fifth Floor R.A.No.595

Sixth Floor R.A.No.596

Seventh Floor R.A.No.596a

b)Shutter : Supplying & Fixing of 55mm thick asbestos free 'TUFWUD' brand - 3 criteria checked - fire, heat and smoke resistant composite Fire check Door Shutter complying with with fire performance - FD 120 as per IS:3614 (part - II) comprising of 2x8mm Calcium Silicate boards over Chemically treated (with Fire retardant chemicals in vaccum pressure impregnation vessels under 160 psi pressure as per IS:401 and kiln seasoned to moistur below 15% as per IS:1141) internal timber (Malaysian Hard Wood, densified to 810 Kilogram/cum) frame work of 100x32 mm with 32mm thick infill of ceramic fiber (density 128 Kilogram/cum), vermaculite mix faced with 3mm Fire retardant High Density fibre board, internally lipped with hardwood beading and pasted in Hydraulic Press under 25 MPa, spray quoted with 2 coats of in-tumescent paint of minimum 300 micron, and with single row of Brush- Type intumescent strip of size 10mmx4mm affixed on periphery for fire and smoke sealing in the slit on all edges of shutter except bottom, without any external lipping.Ground Floor R.A.No.353

First Floor R.A.No.354

Second FloorR.A.No.355

Third floor R.A.No.356

Fouth Floor R.A.No.357

Fifth Floor R.A.No.358

Sixth Floor R.A.No.358a

Seventh Floor R.A.No.358b

Providing and fixing rolling shutter fabricated from steel laths of minimum thickness 0.9 mm. with lock plate of 3.15 mm. thickness reinforced with 35 x 35 x 5 mm. angle section fitted with sliding bolts and handles for both sides, deep M.S. channel section of depth and thickness not less than 65 mm. and 3.15 mm. respectively with hold fast arrangements, M.S. Bracket plate 300 x 300 x 3.15 mm. minimum size and shape with square bar, suspension shaft of minimum 32 mm. diameter, hood cover of M.S. sheet not less than 0.9 mm. thickness and of any size at top and safety devices including mechanical gear operation arrangement consisting of worm gear wheels and worms of high grade cast iron or mild steel and one coat of red lead primer etc. complete. (I.S. 6248-1979) (With mechanical gear)

Providing and Fixing 30 MM thick both side Prelaminated Solid Panel P.V.C. Door Shutter consisting of frame made out of M.S. tubes of 19 guage thickness and, size 19 x 19 mm. for styles and 15 x15 mm. for the top and bottom rails, M.S. frame shall have a coat of metel primer of approved make and manufacture. M.S frame shall be covered with heat mouled PVC ' C ' channel made from 5 mm. (+/- 0.25) thick prelaminated sheet of density 600 kg/cbm, of size 30 mm. thickness 70 mm. width out of which 50 mm. shall be flat and 20 mm shall be tapered in 45 degree angle on either side forming stiles and 5 mm. thick, 95 mm. wide P.V.C. sheet out of which 75 mm. shall be falt and 20 mm. shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm. wide P.V.C. sheet out of which 75 mm. shall be falt and 20 mm. shall be tapered on both sides to form lock rail.Top,bottom and lock rail shall be provided either side of the panel. An additional 5 mm (+/- 0.25) thick PVC strip of 20 mm width is to be stuck on the bottom side of the ' c ' channel prelaminated paneling of 5 mm (+/- 0.25) thick P.V.C. sheet to be fitted inside the M.S. frame welded/ sealed to the styles and rails with 5 mm. (+/- 0.25) x 30 mm. P.V.C. sheet beading on either side and joined together with solvent cement adhesive etc., 10 mm. thickness (5 mm. (+/- 0.25) x 2 nos. ) 20 mm. wide cross P.V.C. sheet as gap insert for the rail and bottom rail. Door to be fixed to frames with 3 nos M.S. powder coated but hinges of size 100 mm. x 25 mm. x 2 mm. using 32 mm. long steel screws drilled suitable to pass through both the walls of the M.S. tube. Other hardwares should be fixed with 19 x 6 mm. size steel screws including fixture fasting complete as per direction of Engineer -in -charge. .

c) Vision Panel: 2 HR rated E Class clear high stress fire rated glass is pre fabricated strategically inside the shutter structure with 10 mm inside the shutter on all sides with U- glazing. An additional insulated powdercoated 'Z' channel of 16 swg MS sheet to be fixed for reinforcement of the joints.Ground Floor R.A.No.359

First Floor R.A.No.360

Second FloorR.A.No.361

Third floorR.A.No.362

Fouth Floor R.A.No.363

Fifth Floor R.A.No.364

Sixth Floor R.A.No.365

Seventh Floor R.A.No.365a

Panic Bar: (For 2 Hr fire Rated single Panic bar) Supplying, fitting & fixing Surface mounted Crash Bar/ panic Bar of touch pad style ,made of heavy duty cast iron/ steel body & latches with SS ,BHMA certified & conforming to ANSI A 156.3 for grade-1 ( 3 hours fire rated ) and suitable for surface mounting to wooden/hollow metal/ Al framed door,with maximum operating force 8Kilogram for unlocking easily & outwardly during emergency,complete in all respect as per direction & satisfaction of Engineer-in charge including all taxes & incidental charges. (Note: To be installed at "FIRE EXIT"only under location specific instruction of Eingineer-in -Charge.) Ground FloorR.A.No.441

First Floor R.A.No.442

Second Floor R.A.No.443

Third floorR.A.No.444

Fouth Floor R.A.No.445

Fifth Floor R.A.No.446

Sixth Floor R.A.No.446A

Seventh Floor R.A.No.446B

Door Closere: (For 2 Hr fire Rated EN-3 Door Closere) Supplying, fitting & fixing Surface mounted overhead Door Closer for 2 hour fire rated doors of different size (e.g size -EN-3 for leaf width upto 900mm) CE certified, marked & conforming to EN - 1154 of approved quality (Internationally reputed brand like Dorma, Geze, Hafele, Assabloy & Magnum etc.) fitted and fixed Complete as per direction & satisfaction of Engineer -in Charge including all taxes & incidental charges.Ground Floor R.A.No.467

First Floor R.A.No.468

Second Floor R.A.No.469

Third floor R.A.No.470

Fouth Floor R.A.No.471

Fifth Floor R.A.No.472

Sixth Floor R.A.No.473

Seventh Floor R.A.No.473A

12"SS Handle: (For 2 Hr fire Rated 12"SS Handle) Supplying, fitting & fixing Stainless Steel 'D' or 'H' type of size 300 mm x 19 mm tubular Handle with Grade 304, CE certified, marked & conforming to EN - 1154 of approved quality (Internationally reputed brand like Dorma, Geze, Hafele, Assabloy & Magnum etc.)as per direction of Eingineer -in Charge fitted and fixed complete including all taxes & incidental charges.Ground Floor R.A.No.346

First FloorR.A.No.347

Second Floor R.A.No.348

Third floor R.A.No.349

Fouth Floor R.A.No.350

Fifth Floor R.A.No.351

Sixth Floor R.A.No.352

Seventh Floor R.A.No.352a

Providing & fixing Rail and Stile (type 01) door of Shakti Hormann make with door frames and leaves made from Galvanized Steel, door leaves constructed from 0.80mm thick galvanized steel sheet formed to provide a 46.6mm thick fully flush, double skin door shell with lock seam joints at stile edges. In-fill of honeycomb kraft paper shall be used to give the required rigidity and effective acoustic and thermal insulation. door frames shall be produced from 1.20mm (18G) thick galvanized steel sheet formed to single rebate profile of size 100mm X 58mm(grooved frame profile). The Door Frames shall be built into the brick or block walls using corrugated “TEE” anchors not welded to the Frames (First Fix). If required frames shall also be fixed on plastered openings with the help of Anchor Fasteners (Second Fix). Door Frames shall be supplied to knockdown from with butt joints for Bolted Assembly at site. Glass should be 200mm X 1400mm,(offset), the Vision Glass shall be fixed flush to both faces (double glazed) of the door to provide ease of cleaning and maintenance. FINISH rail and stile glass 6mm toughned, side and top partitions included as per clients drawings and specs. The rate shall be inclusive of all labour, material, scaffolding, transportation, taxes, price escalation including all leads, lifts at all levels and shall be as directed by Engineer in charge.RA No 1040

Providing and fixing solid core flush door shutter in Single leaf 32 mm thick decorative type of exterior grade with approved face veneers 4 mm thick on both faces and making grooves on the veneer as shown in the drawings or as directed, including all necessary beads, mouldings and lipping, finishing both the faces with French Polish etc, with vision panel of 150x1500mm with 8mm toughened glass with approved etching pattern with approved etching pattern including CCTW frame of 100mm x 60mm including holdfast, chamfering, rounding, rebating, painting, polish & hardware fittings of Hafele/Hettich make, SS matt ball bearing butt hinges, 4 Number - Hafele/Hettich make Mortise Cylinder Lockcase,,Hafele/Hettich omake SS Matt finish 1 pair of Elle lever handle -, Hafele/Hettich make Nickel matt finish Euro profile thumb turn cylinder, Hafele or Hettich make Aluminum surface door closure, Hold open arm , Hafele/Hettich make SS Matt half round floor mounted door stop . The rate shall be inclusive of all labour, material, scaffolding, transportation, price escalation including all leads, lifts at all levels but excluding goods and service tax and shall be as directed by Engineer in charge. R.A.NO.1001

Providing and fixing solid core flush door shutter in Double leaf 32 mm thick decorative type of exterior grade with approved face veneers 4 mm thick on both faces and making grooves on the veneer as shown in the drawings or as directed, including all necessary beads, mouldings and lipping, finishing both the faces with French Polish etc, with vision panel of 150x1500mm with 8mm toughened glass with approved etching pattern with approved etching pattern including CCTW frame of 100mm x 60mm including holdfast, chamfering, rounding, rebating, painting, polish & hardware fittings of Hafele/Hettich make, SS matt ball bearing butt hinges, 4 Number - Hafele/Hettich make Mortise Cylinder Lockcase,,Hafele/Hettich omake SS Matt finish 1 pair of Elle lever handle -, Hafele/Hettich make Nickel matt finish Euro profile thumb turn cylinder, Hafele or Hettich make Aluminum surface door closure, Hold open arm , Hafele/Hettich make SS Matt half round floor mounted door stop . The rate shall be inclusive of all labour, material, scaffolding, transportation, price escalation including all leads, lifts at all levels but excluding goods and service tax and shall be as directed by Engineer in charge.R.A.NO.1002

Providing and fixing solid core flush door shutter in Single leaf 32 mm thick decorative type of exterior grade with approved face laminate 1.5 mm thick on both faces and making grooves on the laminate as shown in the drawings or as directed, including all necessary beads, mouldings and lipping, finishing both the faces with French Polish etc including CCTW frame of 100mm x 60mm including holdfast, chamfering, rounding, rebating, painting, polish & hardware fittings of Hafele/Hettich make SS matt ball bearing butt hinges, 4 Number, Hafele/Hettich make Mortise Cylinder Lockcase-, Hafele/Hettich make SS Matt finish 1 pair of Solid lever handle , Hafele/Hettich make Nickel matt finish Euro profile thumb turn cylinder, Hafele/Hettich make SS Matt half round floor mounted door stop , Hafele/Hettich make SS Matt seamless tower bolt, 8 inch . The rate shall be inclusive of all labour, material, scaffolding, transportation, price escalation including all leads, lifts at all levels but excluding goods and service tax and shall be as directed by Engineer in charge.R.A.NO.1003

Providing and fixing solid core flush door shutter in Double leaf 32 mm thick decorative type of exterior grade with approved face laminate 1.5 mm thick on both faces and making grooves on the laminate as shown in the drawings or as directed, including all necessary beads, mouldings and lipping, finishing both the faces with French Polish etc including CCTW frame of 100mm x 60mm including holdfast, chamfering, rounding, rebating, painting, polish & hardware fittings of Hafele/Hettich make SS matt ball bearing butt hinges, 4 Number, Hafele/Hettich make Mortise Cylinder Lockcase-, Hafele/Hettich make SS Matt finish 1 pair of Solid lever handle , Hafele/Hettich make Nickel matt finish Euro profile thumb turn cylinder, Hafele/Hettich make SS Matt half round floor mounted door stop , Hafele/Hettich make SS Matt seamless tower bolt, 8 inch . The rate shall be inclusive of all labour, material, scaffolding, transportation, price escalation including all leads, lifts at all levels but excluding goods and service tax and shall be as directed by Engineer in charge.R.A.NO.1004

Providing and fixing fibre glass reinforced polyster door shutter 35 mm thick as per IS 14856 (2000) without ventilator with chromium plated handles on both sides, etc. complete.GroundFloor R.A.NO.168

First Floor R.A.NO.169

Second Floor R.A.NO.170

Third Floor R.A.NO.171

Fourth Floor R.A.NO.172

Fifth Floor R.A.NO.173

Sixth Floor R.A.NO.174

Seventh Floor R.A.No.174a

Providing and fixing in position (as per I.S.1868:1982) Aluminium sliding window of two tracks with rectangular pipe having overall dimension 63.50 x 38.10 x 1.02 mm. at weight 0.547 kg/Rmt. and window frame bottom track section 61.85 x 31.75 x 1.20 mm. at weight 0.695 kg/Rmt. Top and side track section 61.85 x 31.75 x 1.30 mm. at weight 0.659 kg/Rmt. The shutter should be of bearing bottom 40 x 18 x 1.25 mm. at weight 0.417 kg/Rmt. Inter locking section 40 x 18 x 1.10 mm. at weight 0.469 kg/Rmt. And handle section 40 x 18 x 1.25 mm at weight 0.417 kg/Rmt. and top section 40 x 18 x 1.25 mm. at weight 0.417 kg/Rmt. As per detailed drawings and as directed by Engineer in charge with all necessary Aluminium sections fixtures and fastenings such as roller bearing in nylon casting and self locking catch fitted in vertical section of shutter including 5 mm. thick plain glass with all required screws and nuts etc, complete with powder coating with box.

Sliding Window (2 Track 2 Glass Shutter Sliding Window with Top Fix (530mm) in 2 Parts) size:- Providing and fixing Sliding Window- 2 Track 2 Glass Shutter Sliding Window with Top Fix (530mm) in 2 Parts as per MYWINDOW SLIMLINE series. The extruded aluminium sections of Alloy 6063 tolerances confirming to DIN standard from approved raw material sources by NALCO. The Size of profile sections with average minimum thickness of 1.5 mm - Track - 66 mm X 47.3 mm (1.5 kg/mtr), Handle Section Depth - 70 mm (0.93 kg/mtr), Interlock Section Depth - 50 mm (0.776 kg/mtr), Shutter Top/Bottom Section Depth - 70 mm (0.96 kg/mtr), Outer frame - 40 mm X 45 mm (0.653 kg/mtr), T- mullion - 70 mm (1.02 kg/mtr). All externally visible surface and the internal visible surfaces will have powder coating finish RAL Colour of 60 -70 micron thickness, Jotun or equivalent. The non visible aluminium surfaces will have minimum chromatizing treatment. All Hardware should be Euro Groove Type-1 compatible,Rollers, Sliding Lock, Corner Cleat, EPDM, all as per MYWINDOW standards, DOW Corning Silicon/GE/Wacker with SS304 screw etc R.A.NO.1064

Sliding Window (2 Track 2 Glass Shutter Sliding Window with Top Fix (530mm) in 2 Parts) size:-Providing and fixing Sliding Window- 2 Track 2 Glass Shutter Sliding Window with Top Fix (530mm) in 2 Parts as per MYWINDOW SLIMLINE series. The extruded aluminium sections of Alloy 6063 tolerances confirming to DIN standard from approved raw material sources by NALCO. The Size of profile sections with average minimum thickness of 1.5 mm - Track - 66 mm X 47.3 mm (1.5 kg/mtr), Handle Section Depth - 70 mm (0.93 kg/mtr), Interlock Section Depth - 50 mm (0.776 kg/mtr), Shutter Top/Bottom Section Depth - 70 mm (0.96 kg/mtr), Outer frame - 40 mm X 45 mm (0.653 kg/mtr), T- mullion - 70 mm (1.02 kg/mtr). All externally visible surface and the internal visible surfaces will have powder coating finish RAL Colour of 60 -70 micron thickness, Jotun or equivalent. The non visible aluminium surfaces will have minimum chromatizing treatment. All Hardware should be Euro Groove Type-1 compatible,Rollers, Sliding Lock, Corner Cleat, EPDM, all as per MYWINDOW standards, DOW Corning silicon/ GE/ Wackers with SS 304 screws, etc.R.A.NO.1059

3 TRACK 2 GLASS SHUTTER WITH 1 MESH SHUTTER WITH BOTTOM FIXED AND SIDE DOUBLE SHUTTER OPNEBLE DOOR Providing & fixing of Sliding Window- 3 Track ( 2 Glass shutter + 1 flymesh ) as per MYWINDOW SLIMLINE series. The extruded aluminium sections of Alloy 6063 tolerances confirming to DIN standard from approved raw material source by NALCO. The Size of profile sections with average minimum thickness of 1.5 mm - 3 Track outer frame - 92 mm X 47.5 mm, 3 Track side – 92 mm x 47.5 mm, Handle - 70 mm x 31 mm, Interlock- 50 mm x 37mm, Shutter top bottom - 70mm x 27.5 mm. glass clip 25.6 mm x 17.7mm, guide rail 8.2 mm x13.13 mm, mesh shutter – 26 mm x 60.81 mm with Saint Gobain Glass fiber strong and durable mosquitoe mesh . for sliding window outer frame -40 mm X 44.8 mm, shutter profile 49 mm X 78 mm,adpter profile 40 mm X 54 mm, Square Clip SGU - 22.5 mm x 22.5 mm, T Mullion - 70mm x 40 mm for bottom fixed and outer frame - 40 mm X 62 mm, Square Clip SGU - 22.5 mm x 22.5 mm,Door Shutter 49 mm X 92.5 mm, Door Bottom 40 mm X 100 mm and Threshold 36 mm x 8 mm for Door. Glass - 6 mm Clear toughened + 8 mm Air Gap + 6 mm Clear Toughened glass from Saint Gobain /Asahi/Modiguard or equivalent as per approved . All externally visible surface and the internal visible surfaces will have powder coating APPROVED RAL finish of 60 -70 micron thickness, Jotun Make or equivalent. The non visible aluminium surfaces will have minimum chromatizing treatment. The outer frame should have 90º fabrication joint with frame insert at all 4 corners made of nylon 6.6 material for better resistance to water leakage.

TOP FIXED GLASS WITH EXHAUST PROVISION AND BOTTOM FIXED LOUVERS Providing & fixing of fixed Aluminium louver window as per MYWINDOW SLIMLINE series. The extruded aluminium sections of Alloy 6063 tolerances confirming to DIN standard from approved raw material sources by NALCO. The Size of profile sections with average minimum thickness of 1.5 millimeter - outer frame - 40 millimeter X 44.8 millimeter , Square Clip Single Glazed Unit - 22.5 millimeter X 22.5 millimeter, T Mullion - 70 millimeter X 40 millimeter, Z louver - 27.8millimeter x 77.7 millimeter. Glass - 6 millimeter frosted toughened from Saint Gobain /Asahi/Modiguard or equivalent as per approved with hole for exhaus fan as supplied. All externally visible surface and the internal visible surfaces will have powder coating of approved RAL finish of 60 -70 micron thickness, Jotun Make or equivalent. The non visible aluminium surfaces will have minimum chromatizing treatment. All Hardware should be Euro Groove Type-1 compatible Corner Cleat, EPDM, drainge cap, PolyVinyl Chloride inserts all as per MYWINDOW standards, DOW Corning silicon/ GE/ Wackers with Stainless Steel 304 screws, etc. NOTE: supply of exhaust fans is excluded The rate shall be inclusive of all labour, material, scaffolding, transportation, taxes, including all leads, lifts at all levels and shall be as directed by Engineer in charge. R.A.NO.1056

TOP HUNG WITH BOTTOM FIXED Single Glazed Unit Providing & fixing of Casement fixed window as per MYWINDOW SLIMLINE series. The extruded aluminium sections of Alloy 6063 tolerances confirming to DIN standard from approved raw material sources by NALCO. The Size of profile sections with average minimum thickness of 1.5 millimetre - outer frame - 40 millimetre X 62 millimetre, shutter profile 49 millimetre X 78 millimeter, adpter profile 40 millimetre X 54 millimetre, Square Clip Single Glazed Unit - 22.5 millimetre X 22.5 millimetre, T Mullion - 70 millimetre X 40 millimetre .Glass - 6 millimetre clear toughened glass from Saint Gobain /Asahi/Modiguard as per approved . .. All externally visible surface and the internal visible surfaces will have powder coating APPROVED RAL finish of 60 -70 micron thickness. The non visible aluminium surfaces will have minimum chromatizing treatment. All Hardware should be Euro Groove Type-1 compatible Cremone Handle , frictions Stay ,Corner Cleat, EPDM, drainage cap, Polyvinyl Chloride inserts all as per MYWINDOW standards, DOW Corning silicon/ GE/ Wackers with Stainless Steel 304 screws, etc. 8,954.56 The rate shall be inclusive of all labour, material, scaffolding, transportation, price escalations including all leads, lifts at all levels and shall be as directed by Engineer in charge however excluding Goods & Service Tax R.A.NO.1066

Providing & fixing of Casement fixed window as per MYWINDOW SLIMLINE series. The extruded aluminium sections of Alloy 6063 tolerances confirming to DIN standard from approved raw material sources by National Aluminium Company. The Size of profile sections with average minimum thickness of 1.5 millimetre - outer frame - 40 millimetre X 44.8 millimetre, shutter profile 49 millimetre X 78 millimetre,adpter profile 40 millimetre X 54 millimetre, Square Clip Single Glazed Unit - 22.5 millimetre x 22.5 millimetre, T Mullion - 70 millimetre x 40 millimetre .Glass - 6 millimetre blue tinted toughened + 8 millimetre Air Gap + 6 millimetre frosted Toughened glass for top panel and bottom panel 6 millimetre blue tinted toughened + 8 millimetre Air Gap + 6 millimetre Clear Toughened glass from Saint Gobain /Asahi/Modiguard. All externally visible surface and the internal visible surfaces will have powder coating of approved RAL finish of 60 -70 micron thickness, Jotun Make. The non visible aluminium surfaces will have minimum chromatizing treatment. All Hardware should be Euro Groove Type-1 compatible Cremone Handle , frictions Stay ,Corner Cleat, Ethylene propylene dieno monomer, drainge cap, Poly vinyl Chloride inserts all as per MYWINDOWstandards, DOW Corning silicon/ GE/ Wackers with SS 304 screws, etc. The rate shall be inclusive of all labour, material, wastages, scaffolding, transportation, taxes, INCLUDING SERVICE TAX, including all leads, lifts at all levels and shall be as directed by Engineer in charge.

Providing waterproofing in W.C. and bath including brick bat coba in all position including providing and laying 12 mm bedding in cement mortor 1:3 on vergin concrete slab with waterproofing compound and finishing the top layer with 20 mm thick brick bedding in cm mortor 1:3 with waterproofing compound 1 kg/ per bag of cement etc. complete.Ground Floor R.A.No.175

First Floor R.A.No.176

Providing & laying water proof treatment of terrace slab with Brick Bat Coba in all position with an average thickness of 150 millimeter consisting specialised materials as per the manufactures specifications and covering 10 years guarantee on court fee stamp paper including all lead, lift etc. complete. Spec. No.: As directed by Engineer in charge.

First Floor R.A.No.597a

Sixth Floor R.A.No.597

Providing water proof bedding for flooring of Bath and Water Closit 25 millimeter thick in Cement Morter 1:3 including using 1 kilo gram of water proof compound per bag of cement including levelling curing etc.complete.Fourth FloorR.A.No.602

Fifth Floor R.A.NO.109a

Sixth Floor R.A.No.604

Seventh Floor R.A.No.604a

Providing water proof bedding for flooring of Bath and WC 25 mm thick in C. M. 1:3 including using 1 kg of water proof compound per bag of cement including levelling curing etc.complete.R.A.No.180

Providing cement based water proofing treatment to terraces (Indian water proofing or alike) with brick bats laid in required slope to drain the water for any span after cleaning the base surface. Applying a coat of cement slurry admixed with approved water proofing compound and laying the brick bats on bottom layer in C.M.1:5 admixed with approved water proofing compound filling up to half depth of brick bats, curing this layer for 3 days, applying cement slurry over this layer joints of brick bats with C.M.1:3 admixed with approved water proofing compound and finally top finishing with average 20 mm. thick layers of same mortar added with jute fiber at 1 Kg. per bag including finishing the surface smooth with cement slurry admixed with approved water proofing compound. Marking finished surface with false squares of 300 mm x 300 mm. making the junctions at the parapet rounded and tapered top for required height, with drip mould at the junction of plaster and parapet and curing and covering 10 years Guarantee against leakproofness on Court fee stamp paper of Rs. 500/- including ponding test etc. complete.

Providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories and stainless steel dash fasteners, stainless steel bolts, etc. of the required size on the top of the floor of the side of waiste slab with suitable arrangement as per approval of engineer in charge (for payment purpose, only the weight of the stainless steel members shall be considered excluding fixing accessories such as nut bolts, fasteners etc.). 50mm dia. pipe, 1.5mm thickness and weight 1.92 kg / r. metre @15 kg/Square Meter Ground Floor RA 298

First Floor R.A.No.299

Second Floor R.A.No.300

Third Floor R.A.No.301

Fourth Floor R.A.No.302

Fifth Floor R.A.No.303

Sixth Floor R.A.No.304

Seventh Floor R.A.No.304a

Supply & Installation of fiber cement plank of SHERA make (External Grade) as duct cladding planks of Cassia/teak/straight grain texture. Dimensions of SHERA planks should be 150mm x 6mm with lenght specified in the drawing precisely machine cut from 1220 x 2440 SHREA sheet with density 1300kg/m3 (±50) on the M.S. frame made from 50x 25x 16 guage with the support at 1500mm made from 50x25x16 guage It should comply to ASTM C1185 and ISO 8336 part (E) for confirming durability properties. SHERA Planks are to be fixed to MS staircase railing as specified in the drawings and approved by authority. SHERA Planks are to be fixed using SHERA Screws of Tensile strength 34N and Shear strength 68N. Planks should be covered with water based cement primer from all 6 sides before installation and finished with 2 coats of water based acrylic paint of 2 tone with brush applied PU coat matt or glossy finish of approved shade. All work to be carried out by SHERA trained applicator. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge. R.A. No. 1023

Supply & Installation of fiber cement plank of SHERA make (External Grade) as pergola of Cassia/teak/straight grain texture. Dimensions of SHERA planks should be 50mm x200 mm x 8 mm with the lenght as required which is precisely machine cut from 1220 x 2440 SHREA sheet with density 1300kg/m3 (±50). It should comply to ASTM C1185 and ISO 8336 part (E) for confirming durability properties. Rate should include supplying and fixing of MS pipe understrucutre of 50x25x16 guage which should be fixed on concrete wall with bolt or fastener and applying paint on it as specified in the drawings and approved by authority. SHERA Planks are to be fixed with using 25mm self drilling screws maintaining 200mm gap in between every pergola using SHERA Screws of Tensile strength 34N and Shear strength 68N. Planks should be covered with water based cement primer from all 6 sides before installation and finished with 2 coats of water based acrylic paint of 2 tone with brush applied PU coat matt or glossy finish of approved shade. All work to be carried out by SHERA trained applicator. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge.R.A. No. 1024

Grab bars-Providing SS grab bars set for accessible toilets comprising of 4 Number. Grab bars as specified below.(1 Number. wing grab bar + 1 Number. L shaped grab bar + 2 Number. straight grab bars = 1 typical set) 27a) Swing grab bar (1 Number) Providing a S.S. 304 SWING HANDICAP GRAB BAR - 700 mm and of DIA: 32MM and thickness 1.5mm of the roved brand and make. 27b) L Shaped grab bar (1 Number) Providing S.S. 304 L SHAPED DISABLED GRAB BAR of IZE-600MM (H) X 600MM (D) and 32MM DIA. and thickness mm of the approved brand and make. 27c) Straight grab bar (2 Number) Providing S.STEEL 304 GRAB RAIL (600 MM),32MM DIA. and thickness 1.5mm of the approved brand and make.R.A.No.305

Providing and fixing mild steel grill work for windows, ventilators etc. 20 Kilogram/Square Metre as per drawing including fixtures, necessary welding and painting with one coats of anticorrosive paint and two coats of oil painting complete.Ground Floor R.A.No.373

First Floor R.A.No.374

Second Floor R.A.No.375

Third Floor R.A.No.376

Fourth Floor R.A.No.377

Fifth Floor R.A.No.378

Sixth Floor R.A.No.379

Seventh Floor R.A.NO.1022

Providing and laying TECTILE TERACOTTA tiles of somany ceramics having 300x300millimeter of 8 to 10millimeter thickness and confirming Indian Standard as per 15622:2006 & Indian Standard 4457:2007 (Group Bla) of approved make, shade and pattern for flooring in required position laid on bed of 1:4 cement mortar including neat cement float, filling joints, curing and cleaning complete.

Providing & Fixing of Armstrong OR equivalent Mineral Fibre Acoustical Suspended Ceiling System with Dune (Bevelled Tegular) Edge Tiles With Armstrong or equivalent 15mm Exposed Grid. The tiles should have Humidity Resistance (RH)of 99%,NRC 0.5, Light Reflectance 85%, Thermal Conductivity k = 0.052 0.057 w/m K, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt 6 &7) in module size of 600 x 600 x 16mm , with Recycled content of 35 %. The tile shall be laid on precoated G.I.channel height 32 with 15 mm wide T section flanges colour white having rotary stitching and XL2 CLIP on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 32mm and a load carrying capacity of 7.57 Kgs/M2 & pull out stength of minimum 100 Kgs.. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system of Armstrong OR equivalent make. etc. complete.First Floor R.A.NO.186

Second Floor R.A.NO.187

Third Floor R.A.NO.188

Fourth Floor R.A.NO.189

Fifth Floor R.A.NO.190

Providing & Fixing of Armstrong or Equivalent Soft Fibre Acoustical Suspended Ceiling System with Optra (Bevelled Tegular) Edge Tiles With Armstrong or equivalent 15mm Exposed Grid. The tiles should have Humidity Resistance (RH) of 95%, NRC 0.91.0,LightReflectance ?85%, Colour White,Fire Performance UK Class 0 / Class 1 (BS 476 pt 6 &7) in module size of 600 x 600 x 15mm , suitable for Green Building application, with Recycled content of 66% GW & 74% RW. The tile shall be laid on precoated G.I channel 32 with 15 mm wide T section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 32 mm and a load carrying capacity of 7 Kgs/M2 with a minimum pull out strength of 100 kgs. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system The Tile & Grid system used together should carry a 10 year warranty. products approved as per GRIHA and BS 476 etc. complete.Gound Floor R.A.No.192

First Floor R.A.No.193

Third Floor R.A.No.195

Fourth Floor R.A.No.196

Fifth Floor R.A.No.197

Sixth Floor R.A.No.198

Providing & Fixing of Armstrong or equivalent Mineral Fibre Acoustical Suspended Ceiling System with ultima (Bevelled Tegular) Edge Tiles With Armstrong or equivalent 15mm Exposed GRID. The tiles should have Humidity Resistance (RH) of 99%, NRC 0.7, Light Reflectance 85%, Thermal Conductivity k = 0.052 0.057 w/m K, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt 6 &7) in module size of 600 x600 x 20mm , suitable for Green Building application, with Recycled content of 32%. The tile shall be laid on precoated G.I.channel on XL2 Clip having a web height of 32 mm with 15 mm wide T section flanges colour white having rotary stitching on all T sections i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 32 mm and a load carrying capacity of 7.7 Kgs/M2 & minimum pull out strength of 100 Kgs.. The T Sections have a Galvanizing of 90 grams per M2 and need to be installed with Suspension system of Armstrong or equivalent make. The Tile & Grid system used together should carry a 10 year warranty. products approved as per GRIHA and BS 476 etc. complete..Sixth Floor R.A.NO.205

Providing and fixing in position Gypsum board false ceiling with 12.5 mm thick Gypsum boards, screwed/fixed to the under structure of suspended G.I. Grid constructed and suspended from the main ceiling consisting of ceiling sections of size 25 x 50 mm maximum center to center distance of 600 milimetre perimeter channel and intermediate channels at maximum center to center distance 1200 milimetre galvanized grid should be fixed to reinforced cement concrete slab. The gypsum board should be fixed to galvanized iron grid with necessary screws. The boards should be taped and filled from underside to give smooth, seamless ceiling. The rate should include necessary additional ceiling sections and intermediate channels. Additional intermediate channels should be fixed to strap hangers for additional support to prevent strapping at every 1200 milimetre item to be completed in all respect including necessary sleeves for ducts finishing of joints cut outs, painting including labour, material, lifts etc. all complete.Gound Floor

First Floor R.A.No.207

Second Floor R.A.No.208

Third Floor R.A.No.209

Fourth Floor R.A.No.210

Fifth Floor R.A.No.211

Sixth Floor R.A.No.212

Seventh Floor R.A.No.212a

Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5 mm thickness in Global white color tile to be laid on grid systems with 15mm wide T - section flanges color white having rotary stitching on the Main Runner, 1200 mm and 600 mm Cross Tees.Providing and Fixing of GI Lay in Plain metal ceiling consisting of 600x600mm Lay in tiles of pre coated galvanized steel in 0.5 mm thickness in Global white color tile to be laid on grid systems with 15mm wide T - section flanges color white having rotary stitching on the Main Runner, 1200 mm and 600 mm Cross Tees.products approved as per GRIHA and BS 476 etc. complete.Ground Floor R.A.No.511

First Floor R.A.No.512

Providing weathered pointing with cement mortar 1:3 for stone/ Brick masonary including scaffolding and curing etc. complete.Ground Floor R.A.No.213

First Floor R.A.NO.214

Second Floor R.A.NO.215

Third Floor R.A.NO.216

Fourth Floor R.A.NO.217

Fifth Floor R.A.NO.218

Sixth Floor R.A.NO.219

Seventh Floor R.A.NO.219a

Providing internal cement plaster 12 mm thick in a single coat using Ready to use wall plaster to concrete or brick surface in all positions including scaffolding and curing complete. Providing groove at joint of B.B. Masonry and concrete members complete. Cement ratio 1:4 With Prior Approval of Concerned S.E. Ground Floor R.A.No.286

First Floor R.A.No.286A

Fourth Floor R.A.No.390

Fifth Floor R.A.No.391

Sixth Floor R.A.No.392

Seventh Floor R.A.No.392a

Providing internal/ external 20 mm thick Ready Mix plaster confirming to IS:4031(Part-4) 1988 and IS 383-1970 in a single coat using Cement mortar of proportion 1:4 containing special type of polymer additives about 0.4 percent, to all type of surfaces in all positions including scaffolding and curing complete

Providing Silica plaster plaster externally in two coats in all positions including base coat of 8 to 10 mm thick curing the same for not less than two days and keeping the surface of base coat rough to receive the final coat treatment 5 to 7 mm thick .finishing the surface by taking out grains and curing for 8 to 10 daysscaffolding etc complete.(The silica plast material shall contain 53 grade OPC cement with pozzolanic materials .size of agreegates shall be of 3 mm having 1:3 proportion with cement.Ground FloorR.A.No.292

First Floor R.A.No.293

Fourth Floor R.A.No.396

Fifth Floor R.A.No.397

Sixth Floor R.A.No.398

Seventh Floor R.A.No.398a

Providing and Fixing of Cerramic Jaalis of Size 200 x 200 x 60 mm, Compressive Strength Not Less than 6 Mpa. Surface finish of Jaalis must be smooth and free from scratches or chipping. Jaalis must be fixed with Tile Adhesive/ Chemical Fixing including Metal Fabrication to meet the lateral support guidelines, as required. Additional Specification as directed by engineer-in-charge. The rate shall be inclusive of all labour, material, scaffolding, transportation, taxes, price escalation including all leads, lifts at all levels and shall be as directed by Engineer in charge.R.A.No.1200

Roof skylight - Providing and fixing of roof skylight Using M.S. stucture of 50x50mm tube combinned with aluminium skylight system with proper drainage facility. Doublewall Polycarbonate sheet ( One full sheet OR minimum possible number of sheets to avoide joints at the top).M.S. tubes are epoxy painted and requires brackets/clamps: bolts, nuts, washers and shims: SS expansion fasteners with bolts, nuts and washers: silicon/EPDM gaskets: drainage provisions: weather seals: flashings and seals at all interfaces with building structure, openings and cladding system, etc. Glass-6mm Blue tinted toughened glass . DOW Corning silicon/ GE/ Wackers with SS 304 screws complete to make the structural glazing air tight and water tight as per IS/BS standards complete as per architectural drawings and specifications as directed by the Engineer-in-charge. The rate shall be inclusive of all labour, material, scaffolding, transportation, taxes, including all leads, lifts at all levels and shall be as directed by Engineer in charge.R.A.No.1202

Providing and laying cement concrete flooring 50mm thick with M20 cement concrete laid to proper level and slope in alternate bays including compaction, filling joints, marking lines to give the appearance of tiles of 30cm x 30cm or other size laid diagonally/ square etc. finishing smooth (with extra cement) in any colour as directed and curing etc. complete. With Natural Sand R.A.No.605

Providing and laying chequered tiles of approved quality of size 30 cmx 30 cm, confirming to corresponding I.S. for flooring in required position laid on a bed of 1:4 cement mortar including cement float, filling joint with cement slurry cleaning curing etc. complete.R.A.No.606

Providing and fixing Heat resistant THERMATEK/Johnson Endura Terrace Tiles (300mm x 300mm x10 mm or higher)with SRI greater than 90.on waterproof and sloped surface of terrace laid on 20 mm thick cool mortar.Terrace floor CPWD DSR 2019, VOL I, ITEM 12.55 PG 885

Providing and fixing of Curtain wall system as per MYWINDOW CW Series. The extruded aluminium sections of Alloy 6063 tolerances confirming to DIN standard from approved raw material source by NALCO. using speclally designed framework including of profile sections with average minimum thickness of 2 millimeter - MULLION 60 millimeter x 128.5 millimeter & transome 60 millimeter x 134millimeter with powder coated All externally visible surface and the internal visible surfaces will have powder coating finish RAL 9010 of 60 -70 micron thickness, Jotun Make or equivalent. The non visible aluminium surfaces will have minimum chromatizing treatment. aluminium extrusions (min 60 micron) in approved colour, hot dip galvanized required brackets/clamps: bolts, nuts, washers and shims: Stainless Steel expansion fasteners with bolts, nuts and washers: silicon/ethylene propylene diene monomer (M-class) rubbergaskets, : drainage provisions: weather seals: flashings and seals at all interfaces with building structure, openings and cladding system, etc. Glass-8 millimeter Blue tinted toughened glass . DOW Corning silicon/ GE/ Wackers with Stainless Steel 304 screws complete to make the structural glazing air tight and water tight as per Indian Standards/Bharat standards standards.complete as per architectural drawings and specifications as directed by the Engineer-in-charge.R.A.No.1021

Providing and fixing ISI marked double swing flush door shutters conforming to IS :2202 (Part I) Non-decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel L- hinges with necessary screws Fittings & Fixtures per leaf SS kick plates on both sides of the door of 300mm height Heavy Duty satin finish butt SS Hinges (100mm x 75mm x 3mm in size) -4 Number. SS finished lever handle with mortise lock- 1 no. Floor spring- 1 No. 100mm x 100mm safety glass at the specified location First floor R.A.No.704

Second floor R.A.No.705

Thrid floor R.A.No.706

Fourth floor R.A.No.707

Fiftth floor R.A.No.708

Sixth floor R.A.No.709

Seventh floor R.A.No.710

Supply, Installation, Testing and Commissioning of 600mm dia MS pipe of 6.3 mm wall thickness as per IS code3589, with zinc dichromate coating from inside and outside of the pipe. All pipes joints to be welded joints. Application of anti microbial coating on the inner side of the pipe is required to avoid mold and bacteria growth. Pipe bedding and surrounding should be of wet well compacted clay to ensure good thermal contact between pipes and the earth. The soil surrounding the pipes should be homogenous and have constant thermal conductivity and if desirable so at site, lime shall be added to clay, as directed by engineer in charge. Peat and dry sand shall not be acceptable. Soil density should be 2000 kg /cum. Installation of sturdy grill with filter and insect screen at the inlet to deter potential intruders shall be included. Additional Specification as directed by engineer-in-charge. The rate shall be inclusive of all labour, material, scaffolding, transportation, taxes, price escalation including all leads, lifts at all levels and shall be as directed by Engineer in charge. EIRL Approved by circle office

Providing and laying telephone black/ Amba whitw/ Cadbury Brown/ Ruby red/ Ocean Brown granite stone of 18 to 20mm thick for door frame/dado / window boxing etc on C.M. 1:6 including filling joints with polymer base fille Numbering/ moulding the sharp edges wherever necessary curring etc completeGround Floor R.A.No.693

First Floor R.A.No.694

Second Floor R.A.No.695

Third Floor R.A.No.695a

Fourth Floor R.A.No.696

Fifth Floor R.A.No.697

Sixth Floor R.A.No.698

Seventh Floor R.A.No.698a

Providing and fixing double scaffolding system (cup lock type) on the exterior side of building/structure, including additional rows of scaffolding in stepped manner as per requirement of site, made with 40mm dia M.S. tube, placed 1.5 metre centre to centre, horizontal & vertical tubes joint with cup & lock system with M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system in the scaffolding for working platform etc. and maintaining it in a serviceable condition for execution of work of cleaning and/ or pointing and/ or applying chemical and removing it thereafter. The scaffolding system shall be stiffened with bracings, runners, connecting with the building etc, wherever required, if feasible, for inspection of work at required locations with essential safety features for the workmen etc., complete as per directions and approval of Engineer-in-charge. Note:- (1) The elevational area of the scaffolding shall be measured for payment purpose. (2) The payment will be made once only for execution of all items for such works.The scaffolding shall be retained till completion of respective works. R.A.No.712

Carrying out core cutting of size 3'' to 5''x 15'' length in the CC/rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as orignal.

Providing and fixing in position alluminium openable shaft door of any size as per detailed drawing and as directed by Engineer in charge with all necessary alluminium sections incuding necessary fixtures and fastening without glass etc. complete with powder coating weight at 10.29 kg/ Square Meter is considered.

RWH - Shallow Percolation Pit Providing, constructing 2.0m deep shallow depth percolation pit comprising of 1.0m dia pre-cast RCC rings, 300mm thick side filling around outside of RCC rings (annular space) with 40mm size boulders including filling of percolation pit up to 0.5m depth (from bottom up) with 25-75mm clean washed gravels followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river sand including netlon mesh between each gravel/sand media layer including covering with RCC slab, manhole frame & cover, PVC rungs etc. including arrangement for inlet & outlet pipe, excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge.

RWH - Recharge Pit Providing, constructing recharge pit of 2.0m deep and 1.0m dia of pre-cast RCC rings with 6.5" dia x 25m deep borewell at the floor of recharge pit including installation of combination of solid/perforated PVC casing pipe wrapped around with netlon mesh including 300mm thick sidefilling around outside of RCC rings (annular space) with 40mm size boulders including filling of recharge pit up to 0.5m depth with 25-75mm clean washed gravels from bottom up followed by 0.5m depth of 10-25mm of clean washed stones followed by 0.5m of washed river sand including netlon mesh between each gravel/sand media layer including covering with RCC slab, manhole frame & cover, PVC rungs, PVC end caps, fittings etc. including arrangement for inlet & outlet pipe excavation & backfilling as shown in the drawing. The rate shall be inclusive of all labour, material, wastage, scaffolding, transportation, taxes, including all leads, lifts at all levels. All material should be of approved make. All works complete as per the drawing, technical specification and direction of the Engineer in charge.

Providing and fixing P.V.C. Rain Water pipes of 110 mm outer diameter and having wall thickness of 2.2 to 2.7 mm confirming to I.S. 13592-1992 including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings, such as, offsets, shoes, inluding fixing the pipe on wall using approved wooden cleats projecting 25mm to 40mm from face of wall a fixing with clips of approved quality and number, filing the joint using rubber gasket with solvent cement and properly resting the shoe of pipes on cement concrete or masonry blocks, including necessary scaffolding and maintenance for 3 yrs for any leakages or dislocations of pipes. All the P.V.C. fittings and additional 2 piece socket clips shall be got approved from engineer in charge etc. complete.

Providing and fixing on walls /ceiling /floor 15 milimetre diameter CPVC pipe with necessary fittings, remaking good the demolished portion. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed complete. Ground Floor R.A.No.221

First Floor R.A.No.222

Second Floor R.A.No.223

Third Floor R.A.No.224

Fourth Floor R.A.No.225

Fifth Floor R.A.No.226

Sixth Floor R.A.No.227

Seventh Floor R.A.No.227a

Providing and fixing on walls /ceiling /floor 25 milimetre diameter CPVC pipe with necessary fittings, remaking good the demolished portion.Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Ground Floor R.A.No.228

First Floor R.A.No.229

Second Floor R.A.No.230

Third Floor R.A.No.231

Fourth Floor R.A.No.232

Fifth Floor R.A.No.233

Sixth Floor R.A.No.234

Seventh Floor R.A.No.234a

Providing and fixing on walls/ ceiling/ floor 32 millimeter diameter Chlorinated polyvinyl chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Spec. No.: BD.V 5 page 551 and as directed by Engineer in charge Ground Floor R.A.NO.235

First Floor R.A.NO.236

Second Floor R.A.NO.237

Third Floor R.A.NO.238

Fourth Floor R.A.NO.239

Fifth Floor R.A.NO.240

Sixth Floor R.A.NO.241

Seventh Floor R.A.No.241a

Providing and fixing on walls /ceiling /floor 40 milimetre diameter CPVC pipe with necessary fittings, remaking good the demolished portion.Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete. Ground Floor R.A.No.242

First Floor R.A.No.243

Second Floor R.A.No.244

Third Floor R.A.No.245

Fourth Floor R.A.No.246

Fifth Floor R.A.No.247

Sixth Floor R.A.No.248

Seventh Floor R.A.No.248a

Providing and fixing on walls /ceiling /floor 50 milimetre diameter CPVC pipe with necessary fittings, remaking good the demolished portion etc. complete. Ground Floor R.A.No.249

First Floor R.A.No.250

Second Floor R.A.No.251

Third Floor R.A.No.252

Fourth Floor R.A.No.253

Fifth Floor R.A.No.254

Sixth Floor R.A.No.255

Seventh Floor R.A.No.255a

Providing and fixing on walls/ ceiling/ floor 65 millimeter diameter Chlorinated polyvinyl chloride pipe with necessary fittings, remaking good the demolished portion etc. complete. Spec. No.: BD.V 5 page 551 and as directed by Engineer in Charge Ground Floor R.A.No.1009

First Floor R.A.No.1009

Second Floor R.A.No.1009

Third Floor R.A.No.1009

Fourth Floor R.A.No.1009

Fifth Floor R.A.No.1009

Providing and fixing on walls/ ceiling/floors, medium grade Chlorinated polyvinyl chloride pipe having embossed Indian Standard Mark on it, of required diameter with screwed sockets, joints, necessary galvanised iron fittings such as sockets,back nuts,elbows, bends, tees, reducers, enlargers, plugs, clamps etc.including necessary drilling holes in walls, slabs etc. and remaking good the demolished portion to restore the same in original condition neatly and providing and applying anticorrosive primer and two coats of oil painting, testing, etc.complete.(Prior approval of sample by Ex.Engineer is necessary before use) For multistory building only. For 80 millimeter Fourth Floor 1035

Providing and fixing in position tested heavy quality "Leader" make "Non return" of 25 mm having both ends screwed male etc. complete/ R.B.O. brass ball valves RA No. 1027

Providing and fixing in position tested heavy quality "Leader" make "Non return" of 40 millimeter having both ends screwed male etc. complete/ R.B.O. brass ball valves R.A.NO.1038

Providing and fixing in position tested heavy quality "Leader" make brass ball valve of 15 millimeter having both ends screwed male etc. complete/ R.B.O. brass ball valves R.A.NO. 1010

Providing and fixing in position tested heavy quality "Leader" make brass ball valve of 25 millimeter having both ends screwed male etc. complete/ R.B.O. brass ball valves RA No. 1026

Providing and fixing in position tested heavy quality "Leader" make brass ball valve of 32 millimeter having both ends screwed male etc. complete/ R.B.O. brass ball valves R.A.NO. 1011

Providing and fixing in position tested heavy quality "Leader" make brass ball valve of 40 millimeter having both ends screwed male etc. complete/ R.B.O. brass ball valvesR.A.NO. 1012

Providing and fixing in position tested heavy quality "Leader" make brass ball valve of 50 millimeter having both ends screwed male etc. complete/ R.B.O. brass ball valves RA No. 1028

Providing and fixing in position tested heavy quality "Leader" make brass ball valve of 65 millimeter having both ends screwed male etc. complete/ R.B.O. brass ball valves R.A.NO.1013

Providing and fixing in position tested heavy quality "Leader" make brass ball valve of 80 mm having both ends screwed male etc. complete/ R.B.O. brass ball valves R.A.NO.1014

Providing and fixing 100 mm diameter stabiliser pipe/ P.V.C. soil vent/ waste pipe and with necessary fixtuers and fiting such as bends, tees, single junctions slotted vent, clamps etc. complete.

Ground Floor R.A.No.613

First Floor R.A.No.614

Second Floor R.A.No.615

Third Floor R.A.No.616

Fourth Floor R.A.No.617

Fifth Floor R.A.No.618

Sixth Floor R.A.No.619

Seventh Floor R.A.No.619a

Providing and fixing P.V.C. Rain water pipes of 160 mm outer diameter including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings. Ground Floor R.A.No.671

First Floor R.A.No.672

Second Floor R.A.No.673

Third Floor R.A.No.674

Fourth Floor R.A.No.675

Fifth Floor R.A.No.676

Sixth Floor R.A.No.677

Seventh Floor R.A.No.677a

Providing and fixing 45 centimetre wide steel ladder of 40 milimetre x 6 milimetre mild steel flat stringers and steps of 18 milimetre diameter mild steel bar for water tank including fixing it in (1:2:4) Mix-15 cement concrete block 60 centimetre x 30 centimetre x 30 centimetre and painting the ladder complete. Ground Floor R.A.No.256

Fourth Floor R.A.No.260

Fifth Floor R.A.No.261

Sixth Floor R.A.No.262

Seventh Floor R.A.No.262a

Providing and fixing 75mm diameter stabiliser pipe /P.V.C. soil vent /waste pipe and with necessary fixtuers and fiting etc. complete.

Ground Floor R.A.No.634

First Floor R.A.No.635

Second Floor R.A.No.636

Third Floor R.A.No.637

Fourth Floor R.A.No.638

Fifth Floor R.A.No.639

Sixth Floor R.A.No.640

Seventh Floor R.A.No.640a

Providing, laying & fixing P.V.C. pipe of 110 mm. diameter with fittings such as bends, tees, reducers, clamps etc. including necessary excavation, trench filling etc. complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc. complete.

Ground Floor R.A.No.531

First Floor R.A.No.532

Second Floor R.A.No.533

Third Floor R.A.No.534

Fourth Floor R.A.No.535

Fifth Floor R.A.No.536

Sixth Floor R.A.No.537

Seventh Floor R.A.No.537a

Providing and fixing P.V.C. Rain water pipes of 160 mm outer diameter including proper rainwater receiving recess with P.V.C. plug, bend, necessary fittings. Ground Floor R.A.No.671

Providing and fixing white glazed Jaquar make urinal of series URS-WHT-13257 with Pressmatic auto closing valve of Jaquar make having code PRS-077G, 32 millimeter diameter Poly Vinyle Chloride flush pipe with fitting and flushing arrangement including lead soil pipe, lead trap & soil pipe connection upto the outside face of wall Etc.complete. R.A.NO.1015

Providing and fixing white JAQUAR MAKE Opal series European type wall-hung, Code is OPS-WHT-15951 of size 400millimeter x 370millimeter x 575 millimeter with Jaquar make flush valve having code no. FLV-1089SQG, including soil pipe, vent pipe upto outside face of wall, 100 millimeter dia Cast Iron plug bend inlet pipe all fittings,cutting & making good walls, floors etc R.A.NO.1036

Providing and fixing white JAQUAR MAKE Aria series european type wall-hung,Code is ARS-WHT-39951 of size 360millimeter x 360millimeter x 575 millimeter withJaquar make flush valve having code no. FLV-1089SQG, including soil pipe, vent pipe upto outside face of wall, 100 millimeter dia Cast Iron plug bend inlet pipe all fittings,cutting & making good walls, floors etc. Ground Floor

First Floor R.A.NO.1037

Providing and fixing 25 mm. dia Ball cock medium type with PVC float including sockets & necessary fittings and tested as per municipal requirements etc. complete. Spec. No.: As directed by Engineer in charge. Ground Floor

First Floor RA No. 1030

Providing and fixing 50 millimeter diameter Ball cock medium type with PolyVinyl Chloride float including sockets & necessary fittings and tested as per municipal requirements etc. complete. Spec. No.: As directed by Engineer in charge. For OHT R.A.NO.1039

Providing and fixing 40 millimeter diameter Ball cock medium type with PolyVinyl Chloride float including sockets & necessary fittings and tested as per municipal requirement etc. complete. Spec. No.: As directed by Engineer in charge. For OHT R.A.No.641

Providng and fixing stainless steel sink of size 600 x 510 x 200 millimeter of Nirali or equivalent make including coupling, outlet pipe, elbow and other necessary fitting, finishing complete.Ground Floor R.A.No.679

1st floor R.A.No.679

2nd floor R.A.No.680

3rd floor R.A.No.681

4th floor R.A.No.682

5th floor R.A.No.683

6th floor R.A.No.684

7th floor R.A.No.684a

Providing and fixing Jaquar make sink cock with regular swinging spout (Wall Mounted Model) with wall flange Having code no. DRC-37347 / 37347 GA / 37347 GB / 37347 GD incluidng other necessary fitting, etc. complete. R.A.No.1017

Providing and fixing C.P. 2 Way BIB cock with wall flange of Jaquar make series Code No.LYR-38041 / 38041 GA / 38041 GB / 38041 GD including necessary sockets/ union nut etc. complete. R.A.No.1018

Providing and fixing Jaquar make series Hand shower (health faucet) with 8millimeter diameter 1 Meter long flexible tube having code no - ALD-573 / 573 GD / 537 GA / 573 GB and wall hook including necessary sockets/ union nut etc. complete. R.A.No.1019

Providing and fixing jaquar make series Oval Type Under Counter Wash Hand Basin of 420 x 590 x 195(millimeter) size model no. CNS-WHT-705, with Jaquar make pillar cock, code no. DRC-37001 / 37001 GA / 37001 GB / 37001 GD, C.P.Angular stop cock long thread jaquar make continental (Cat.No. CON-059) including SS bottal trap of jaquar make having coad no. ALD-769L and necessary pipe connection up to the outside face of the wall,.having Telephonic Black / Colour Granite of 180 millimeter thick fixed on Black Kadappa Framework, etc. Complete. R.A.NO.1020

Providing and fixing Jaquar make Table top white wash basin of size 120x635x405 mm -code no. LYS-WHT-38901N, rubber plugs and brass chain, with Jaquar make pillar cock, code no. LYR-38021 / 38021 GA / 38021 GB / 38021 GD, C.P.Angular stop cock long thread jaquar make continental (Cat.No. CON-059) including SS bottal trap of jaquar make having code no. ALD-769L and necessary pipe connection up to the outside face of the wall.etc complete. RA No. 1021

Providing and fixing Jaguar make Shower Head OHS-CHR-35497 / 35497 GD / 35497 GA / 35497 GB, with Jaquar make shower arm code no. SHA-49483, Jaquar make shower tube code no. SHA-549 D12, Jaquar make hand shower code no. HSH-1937 / 1937 GD / 1937 GA / 1937 GB, with Jaquar make divertor of code no. ALD-079 and FLR-5079K with Jaquar make spout code no. SPJ-5463 / 5463 G / 5463 GA / 5463 GB / 5463 GD / 5463 GE, including all necessary pipe fittings and connections etc. complete. RA No. 1031

Providing and fixing bib cock with nozzle of Jaquar make with code no. CON-CHR-049KN including necessary sockets/union nut etc. complete. RA No. 1034

Providing and fixing Jaquar make Urinal partition with code no. 1810, of size 900 millimeter x 450 millimeter with frosted safety glass 8 millimeter thick, incluidng other necessary fitting, etc. complete. RA No. 1022

Providing and fixing C.P. Angular stop cock with wall flange jaquar make continental (CAT.NO. CON-059) including necessary sockets/union nut etc. complete. RA No. 1023

Fixing on Concrete / Brick Base Material for Multiple Pipe System Providing and Fixing of Hilti make C shaped slotted channels/brackets MQ-41 of 41 millimeter X 41 millimeter dimension and thickness of 2 mm.The channel should have slotted holes on one side for adjustability and should have serrated and bent edges on the other side. The channel should have inward rolled lip with serrations. The material should be S250 GD steel as per DIN 10147, pre-galvanised ( to approx. 20 microns). The slots should be of dimension 63 millimeter X 13.5 millimeter and channel should have indicative length markings.The channel should have slotted holes on one side for adjustability and should have serated and bent edges on the other side. For concrete wall - The channel should be fixed with Hilti make 2 numbers of HSV M12 x 100 Mechanical stud anchor for wall and ceiling, Bolt should be carbon steel with galvanised to min 5 micron with DIN125 washer, Anchor bolt should be embed 65 millimeter inside the base material with drilling and 2 times cleaning with wire brush and blow pump, to take the supports either from wall or ceiling. Old approved RA 1001

Pipe Rings - Multiple Pipes Diameter Range Providing and Fixing of Hilti make Piperings MPN-RC supported from walls or ceiling of below diameters. The pipe ring should have an ethylene propylene diene monomer (M-class) rubberrubber inlay of hardness 40o +- 5o Shore A. The pipe ring should have a noise reduction factor of 15Decibel and temperature resistance of -40 degree Celsius to 110 degree Celsius. The pipe ring should be fixed on the Hilti make channel support MQ41 with Hilti make MQA- M10 pipering saddle with Hilti make Anchor Rod HIT-C M10, with Nut of M10 class (DIN934) + Washer (DIN125):- The rate shall be inclusive of all labour, wastages, material, scaffolding, transportation, taxes, INCLUDING SERVICE TAX, including all leads, lifts at all levels and shall be as directed by Engineer in charge. For approximate pipe diameters mentioned below 15 millimeter Old approved RA 1002

20 millimeter Old approved RA 1003

25 millimeter Old approved RA 1004

32 millimeter Old approved RA 1005

40 millimeter Old approved RA 1006

50 millimeter Old approved RA 1007

65 millimeter Old approved RA 1008

Pipe Rings - Multiple Pipes Providing and Fixing of Hilti make Piperings MPN-RC supported from walls or ceiling of below diameters. The pipe ring should have an EPDM rubber inlay of hardness 40o +- 5o Shore A. The pipe ring should have a noise reduction factor of 15 dB and temperature resistance of -40oC to 110oC. The pipe ring should be fixed on the Hilti make channel support MQ41 with Hilti make MQA- M16 pipering saddle with Hilti make Anchor Rod HIT-C M16, with Nut of M16 class (DIN934) + Washer (DIN125):- The rate shall be inclusive of all labour, wastages, material, scaffolding, transportation, taxes, including all leads, lifts at all levels and shall be as directed by Engineer in charge. For approximate pipe diameters mentioned below 160 millimeter Old approved RA 1011

Fixing on Concrete / Brick Base Material for Single System Providing and Fixing of Hilti make Piperings MPN-RC supported from walls or ceiling of below diameters. The pipe ring should have an ethylene propylene diene monomer (M-class) rubberrubber inlay of hardness 40o +- 5o Shore A. The pipe ring should have a noise reduction factor of 15Decibel and temperature resistance of -40 degree Celsius to 110 degree Celsius. For concrete wall - The pipe ring should be fixed on Hilti make Anchor Rod HIT-C M10 and properly inserted in a concrete wall or ceiling with Hilti make HKV-M10 x 40 with proper drilling and 2 times cleaning with wire brush and blow pump. Brick Wall - The pipe ring should be fixed on Hilti make Anchor Rod HIT-C M16 and properly inserted in a Brick wall with Hilti make HIT-HY-70 + HIT-V (5.8) M10 x 185 Anchor. The Anchor should be embeded 150 millimeter inside the base material with drilling and 2times cleaning with wire brush and blow pump The rate shall be inclusive of all labour, wastages, material, scaffolding, transportation, taxes, including all leads, lifts at all levels and shall be as directed by Engineer in charge. For pipe diameters mentioned below 75 millimeter Old approved RA 1009

Fixing on Concrete / Brick Base Material for Single System Providing and Fixing of Hilti make Piperings MPN-RC supported from walls or ceiling of below diameters. The pipe ring should have an ethylene propylene diene monomer (M-class) rubberrubber inlay of hardness 40o +- 5o Shore A. The pipe ring should have a noise reduction factor of 15Decibel and temperature resistance of -40 degree Celsius to 110 degree Celsius. For concrete wall - The pipe ring should be fixed on Hilti make Anchor Rod HIT-C M10 and properly inserted in a concrete wall or ceiling with Hilti make HKV-M10 x 40 with proper drilling and 2 times cleaning with wire brush and blow pump. Brick Wall - The pipe ring should be fixed on Hilti make Anchor Rod HIT-C M16 and properly inserted in a Brick wall with Hilti make HIT-HY-70 + HIT-V (5.8) M10 x 185 Anchor. The Anchor should be embeded 150 millimeter inside the base material with drilling and 2times cleaning with wire brush and blow pump The rate shall be inclusive of all labour, wastages, material, scaffolding, transportation, taxes, including all leads, lifts at all levels and shall be as directed by Engineer in charge. For pipe diameters mentioned below 75 millimeter

Fixing on Brick / Concrete Base Material for Single System Providing and Fixing of Hilti make Piperings MPN-RC supported from walls or ceiling of below diameters. The pipe ring should have an ethylene propylene diene monomer (M-class) rubberrubber inlay of hardness 40o +- 5o Shore A. The pipe ring should have a noise reduction factor of 15Decibel and temperature resistance of -40 degree Celsius to 110 degree Celsius. Concrete wall - The pipe ring should be fixed on Hilti make Anchor Rod HIT-C M16 and properly inserted in a concrete wall or ceiling with Hilti make HKV-M16 x 65 with proper drilling and 2 times cleaning with wire brush and blow pump. Brick Wall - The pipe ring should be fixed on Hilti make Anchor Rod HIT-C M16 and properly inserted in a Brick wall with Hilti make HIT-HY-70 + HIT-V (5.8) M16 x 185 Anchor. The Anchor should be embeded 150 millimeter inside the base material with drilling and 2times cleaning with wire brush and blow pump The rate shall be inclusive of all labour, material, wastages, scaffolding, transportation, taxes, including all leads, lifts at all levels and shall be as directed by Engineer in charge. For pipe diameters mentioned below 110mm Old approved RA 1013

160 millimeter Old approved RA 1015

Supply, fixing, jointing, testing in position in Rinforced Cement Concrete tanks Galvonized Iron pipe inserts with puddle plates of required diameter for over flow drain, inlet and outlet of required diameters etc. complete including all leads, lifts and wastage as per direction of Engineer in Charge R.A.NO.1033

providing and fixing on walls/ceiling/floor 20 mm dia. CPVC pipe with necessary fittings, remaking good the demolished portion etc.complete. Including removing existing pipe line if necessary and conveying and stacking the same in PWD chowky or as directed etc.complete. Completed Rates excluding GST in Rs. 221 Labour Rate excluding GST in Rs.22 Ground Floor R.A.No.685

First Floor R.A.No.686

Second Floor R.A.No.687

Third Floor R.A.No.688

Fourth Floor R.A.No.689

Fifth Floor R.A.No.690

Sixth Floor R.A.No.691

Seventh Floor R.A.No.692

Supply, installation, testing and commissioning of PRV stations consisitng of two PRV 65MM each on supply and bypass lines per station, including isolation valves for both The PRV must be of approved make confirming to EN1988. (PN6 rating unless otherwise mentioned) with inlet connections of specified sizes, with unions, washers,isolation valves, gaskets. The installation must be carried out as per the standard procedure as directed by the EIC.RA No 1203

Rate approved by Circle office Supply, installation, testing and commissioning of PRV stations consisitng of two PRV 50MM each on supply and bypass lines per station, including isolation valves for both The PRV must be of approved make confirming to EN1988. (PN6 rating unless otherwise mentioned) with inlet connections of specified sizes, with unions, washers,isolation valves, gaskets. The installation must be carried out as per the standard procedure as directed by the EIC. second floor

Supply, installation, testing and commissioning of PRV stations consisitng of two PRV 40MM each on supply and bypass lines per station, including isolation valves for both The PRV must be of approved make confirming to EN1988. (PN6 rating unless otherwise mentioned) with inlet connections of specified sizes, with unions, washers,isolation valves, gaskets. The installation must be carried out as per the standard procedure as directed by the EIC. second floor Rate approved by Circle office

Supply, installation, testing and commissioning of Resilient Seated automatic air relief valve confirming to IS 14845 (PN10 rating unless otherwise mentioned) with inlet connections of specified sizes, with unions, washers, gaskets. The installation must be carried out as per the standard procedure as directed by the EIC. Rate approved by Circle office

Supply, installation, testing and commissioning of 40mm dia electrically actuated butterfly valves, electrical actuator, polyethylene level floats with sensor cable and control assembly for float, inlet connections of specified sizes, bolts, nuts washers, gaskets.The installation must be carried out as per the standard procedure as directed by the EIC. The rate shall be inclusive of all labour, leads, lifts at all levels and shall be directed by EIC Basement lvl UGWT

Terrace lvl OHWT Rate approved by Circle office

Supply, installation, testing and commisioning of multiple entry floor trap with three 50mm inlets and 75mm outlet with 50mm deep water seal of approved make etc complete as directed by the EIC. The trap shall be of HDPE / PVC / PVC Silent / Polypropylene the same as that used for the piping item. Rate approved by Circle office

Supply, installation, testing and commissioning of oil & grease separator confirming to EN 1825 of 200L capacity and the standard procedure etc complete as directed by the EIC Rate approved by Circle office

Providing and fixing dia 100mm PVC pipe sleeves of following diameters up to maximum of 400 mm length including necessary cutting, fixing in position, levelling, at all levels/heights, scaffolding, staging etc. complete as per drawings and as directed by Engineer in charge. The rate shall be inclusive of all labour, material, scaffolding, transportation, taxes, price escalation including all leads, lifts at all levels and shall be as directed by Engineer in charge. 100mm

200mm Rate approved by Circle office

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 100 mm dia with necessary fittings as per specification no.FF-PP Domestic Water Line Electrical SSR

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings as per specification no.FF-PP Flushing Water Line Electrical SSR

Providing, laying and fixing P.V.C. pipe of 75mm dia. Ground Floor RA No 263

First Floor RA No 264

Second Floor RA No 265

Third Floor RA No 266

Fourth Floor RA No 267

Fifth Floor RA No 268

Sixth Floor RA No 269

Seventh Floor RA No 269a

Providing and laying in trenches 80 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes-Flushing water pipe R.A.No.545

Providing and laying in trenches 80 mm dia. heavy grade having embossed as ISI Mark galvanised iron pipes Electrical SSR

Sewage Treatment PlantDesigning, Supplying, Fixing , Unloading, Installation & Commissioning of Packaged sewage treatment & recycling plant of AirObix make; including of all equipment such as pumps, diffusers, internal piping, filters, Electric panals etc . The rate shall include all items to make Sewage Treatment Plant successfully operational including all eletrical, mechanical & plumbing accessories. Refer to specifications for details RA No 1204

Providing and making ISI Mark ferrule connection of 50 millimetre diameter metre to water main including excavation and reinstatement complete RA No 530.

Providing and supplying in standard lengths Polyethylene (PE) Pipes for non pressure underground drainage and sewerage with smooth internal and corrugated (profiled) external surface with anti rodent property conforming to ISO-21138-3:2007 (D-REX pipe of Rex Polyextrusion or approved equivalent) with necessary jointing material like mechanical connectors, i.e. thread/ insert joint/quick release coupler joint/ compression fitting joint or flanged joint, including all taxes (Central and local), transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores/site and stacking the same in closed shade duly protecting from sunrays and rains, etc. complete . Also includes lowering, laying and jointing H.D.P.E. Double Wall Corrugated Pipes for non pressure Underground drainage and Sewerage applications and specials of following class and diameter including cost of conveyance from stores to site of works including cost of all labour, material except O ring coupler giving satisfactory hydraulic testing as per relevant ISO, etc. completeH.D.P.E. pipes for Drainage (Class SN8) 160mm (OD) RA. No. 1179

200mm (OD) RA. No. 1177

250mm (OD) RA. No. 1179

315mm (OD) RA. No. 1180

Providing, supplying, lowering laying & jointing in standard lengths Polyethelene Pipes, confirming to IS 4984 / 14151 / 12786 / 13488 with nesessary jointing material like mechanical connector i. e. thread / insert joint / quick release coupler joint / compression fitting joint or flanged joint excluding coupler/specials, including transportation and freight charges, inspection charges, loading / unloading charges, conveyance to the departmental stores & stacking the same in closed shade duly protecting from sunrays & rains, excluding GST levied by GI & GOM in all respect etc. complete. 10 Kg/Sq. cm : 160mm (OD) MJP DSR 2019-20, SECTION I(IX), ITM NO 1&2, Pg No 154, 155

200mm (OD) MJP DSR 2019-20, SECTION I(IX), ITM NO 1&2, Pg No 154, 155

250mm (OD) MJP DSR 2019-20, SECTION I(IX), ITM NO 1&2, Pg No 154, 155

315mm (OD) MJP DSR 2019-20, SECTION I(IX), ITM NO 1&2, Pg No 154, 155

Providing & constructing Brick Masonry Inspection Chamber 90cm x 45cm x 90cm including 1:4:8 cement concrete foundation 1:2:4 cement concrete channels half round G.S.W. pipes, Brick Masonry, plastering from inside and airtight C.I. lid 65 kg with frame fixed in cement concrete etc.complete. Spec. No.: Bd.V.43, Page No. 574

Providing and constructing on sewer, B.B. masonry circular manhole with concentric cone 1.2 M dia. at bottom and 0.5 M dia. at top and upto a depth of 2.00 M with 23 cm brick work in CM 1:4 proportion excluding excavation including foundation concrete 250 mm thick and haunches and channels in C.C. 1:2:4 proportion, finishing channels in smooth rendering, providing C.I. dapuri type steps each weighing 5.5 kg., 1:2:4 coping and providing and fixing approved make and quality S.F.R.C. frame and cover of 56 cm dia. etc. complete as directed by Engineerin-charge. MJP DSR, SEC L, ITM NO 6, Pg No 296

Providing and fixing 15cm x 10cm salt glazed stoneware gully trap in cement concrete 1:4:8 outside the building including cast iron grating in the sink, connecting glazed stoneware pipe, brick masonry chamber with cast iron lid and cast iron grating for the gully trap. Spec. No.: Bd.V.38, Page No. 572 RA No 528

Valve chamber with cast iron manhole frame and covers Providing and constructing valve chamber of 60 x 45 cm internal size and depth upto 0.9 M with 60 x 45 cm size CI manhole frame and cover of 40 kg with B.B. masonry 15 cm thick 1:3:6 proportion PCC be MJP DSR 2019-20, SECTION L, ITM NO 2, 294

Providing, lowering laying & jointing ISI standard R.C.C. pipes in standard lengths of following class and diameter suitable for either collar joints or rubber ring joints, excluding GST lev-ied by GOI & GOM in all respect including inspection charges, transport to departmental stores, unloading and stacking etc. complete as per IS-458/1988. 300mm- NP3 MJP DSR, SEC I V, ITM NO 1 & 2, Pg No 124

Providing, lowering laying & jointing ISI standard R.C.C. pipes in standard lengths of following class and diameter suitable for either collar joints or rubber ring joints, excluding GST lev-ied by GOI & GOM in all respect including inspection charges, transport to departmental stores, unloading and stacking etc. complete as per IS-458/1988. 450mm MJP DSR, SEC I V, ITM NO 1 & 2, Pg No 124

Providing, lowering laying & jointing ISI standard R.C.C. pipes in standard lengths of following class and diameter suitable for either collar joints or rubber ring joints, excluding GST lev-ied by GOI & GOM in all respect including inspection charges, transport to departmental stores, unloading and stacking etc. complete as per IS-458/1988. 600mm MJP DSR, SEC I V, ITM NO 1 & 2, Pg No 124

Providing and fixing 25mm diameter water meter with non-returnvalve including strainer, sockets/union nut and including water meter box making locking arrangement and lock. [Without chamber]. Spec. No.: Bd.V.7 Page No. 554 R.A.No.546

Providing and fixing 8 cm rigid PVC Nahani trap including PVC grating ,bend, connecting piece of UPVC pipe upto the outside face of wall ,making the good damaged surface and testing etc. complete ( Prior approval of sample and brand by Ex. Engr. is necess Ground Floor R.A.No.547

First Floor R.A.No.548

Providing and fixing H.D.P container Syntex or alike one piece moulded water tank made out of high density polythyler and built corrugated inclusive of delivery up to destination hoisting and fixing of accessories such as inlet,outlet overflow pipe inclus R.A.No.529

Fixing of Supports at bottom of ceiling Providing and fixing Hilti make Piperings MPN-RC 160mm diameter, supported from ceiling. The pipe ring should have an EPDM rubber inlay of hardness 40o +- 5o Shore A. The pipe ring should have a noise reduction fact Old approved RA 1018

Providing & fixing heat insulation by wrapping the pipes with glass wool/asbestos fibre rope or tape/videoflex 15 milimetre as directed by Engineer in charge. RA No. 557

Providing and fixing heat insulation by wrapping the pipes with glass wool / asbestosfibre rope or tape / videoflex for 25 mm diameter pipe etc. complete. Including all leads, lifts and wastages as per direction of Engineer in Charge Ground floor R.A.No.555

Scupper/Parapit roof drain/Roof corner drain of 110 mm size

Estimation No:-121131-1/2019-20Providing Internal Electrification to the state of Art Building and Campus (Staff Quarter's Building, Dg Bungalow and VIP Guest House ) for MEDA, at Aundh, Pune.

LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Buttom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Seminice Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * The APFC panel should be complete with all required protection , Accessories , wiring Etc. * All ACB's shall be EDO. * Reffer Electrical Main Single Line diagrams for panel details. Incomer: 1000A,4P,ACB with 50KA Breaking Capacity with Microprocessor Based LSIG Protection - 1Nos 630A,4P,MCCB with 36KA Breaking Capacity with Microprocessor Based LSI Protection - 1Nos Outgoing Feeders: 100A,4P,MCCB with 25KA Breaking Capacity with thermal Magnetic release with Overload and Short circuit protection - 3Nos 125A,4P,MCCB with 25KA Breaking Capacity with thermal release with Overload and Short circuit protection- 1Nos

Supply, Installation, Testing and commissioning of Main LT Panel 2 LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Bottom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * Refer Electrical Main Single Line diagram for panel details. 160A,4P,MCCB with 25KA Breaking Capacity with thermal release with Overload and Short circuit protection- 1Nos 250A,4P,MCCB with 16KA Breaking Capacity with thermal release with Overload and Short circuit protection- 3Nos 32A,4P,MCCB with 16KA Breaking Capacity with thermal release with Overload and Short circuit protection- 1Nos 400A,4P,MCCB with 25KA Breaking Capacity with Microprocessor Based with Overload and Short circuit protection- 1Nos 63A,4P,MCCB with 16KA Breaking Capacity with thermal release with Overload and Short circuit protection- 1Nos 200A,4P,MCCB with 25KA Breaking Capacity with thermal release with Overload and Short circuit protection- 1Nos 320A,4P,MCCB with 25KA Breaking Capacity with Microprocessor Based with Overload and Short circuit protection- 1Nos 630A,4P,MCCB with 36KA Breaking Capacity with Microprocessor Based with Overload and Short circuit protection- 1Nos Bus bars Rating : 1000A,3Phase,50KA,50Hz Cu Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Multifunction Meter With RS-485, CT for APFC Panel

Supply, Installation, Testing and commissioning of Main Lighting Panel (MLP) LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Buttom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * * Refer Electrical Main Single Line diagrams for panel details. Incomer: 100A,4P,MCCB with 16KA Breaking Capacity with thermal release- 1Nos Outgoing Feeders: 25A,DP,MCB with 10KA - 2Nos 25A,4P,MCB with 10KA - 19Nos Bus bars Rating : 125A,3Phase,16KA,50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Ammeter Meter

Supply, Installation, Testing and commissioning of Main Power Panel (MPP) LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Bottom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * Ref Electrical Main Single Line diagram for panel details. Incomer: 400,4P,MCCB with 25KA Breaking Capacity with Microprocessor Based Overload and Short circuit protection - 1Nos Outgoing Feeders: 200A,4P,MCCB with 10KA -1 Nos 63A,4P,MCB with 10KA -10 Nos 40A,4P,MCB with 10KA - 10Nos 32A,4P,MCB with 10KA - 11Nos Bus bars Rating : 500A,3Phase,25KA,for 1 Sec 50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Ammeter Meter.

Supply, Installation, Testing and commissioning of UPS-1 Distribution Panel (10KVA UPS ) LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Bottom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * Refer Electrical Main Single Line diagrams for panel details. Incomer: 32A,4P,MCCB with 16KA Breaking Capacity with thermal release with Overload and Short circuit protection - 1Nos Outgoing Feeders: 25A,4P,MCB with 10KA - 19Nos 25A,DP,MCB with 10KA - 2Nos Bus bars Rating : 40A,3Phase,10KA,50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Ammeter Meter.

Supply, Installation, Testing and commissioning of UPS Power Distribution Panel LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Bottom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * Refer Electrical Main Single Line diagrams for panel details. Incomer: 250A,4P,MCCB with 16KA Breaking Capacity with thermal release Overload and Short circuit Protection - 1Nos Outgoing Feeders: 25A,DP,MCB with 10KA - 6Nos 25A,4P,MCB with 10KA - 1Nos 32A,4P,MCB with 10KA - 4Nos 40A,4P,MCB with 10KA - 6Nos Busbars Rating : 320A,3Phase,16KA,50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Ammeter Meter

Supply, Installation, Testing and commissioning of Main ACDB LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Bottom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with With R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * Refer Electrical Main Single Line diagrams for panel details. Incomer: 63A,4P,MCCB with 16KA Breaking Capacity with thermal release overload and Short circuit - 1Nos Outgoing Feeders: 25A,DP,MCB with 10KA - 15Nos Busbars Rating : 100A,3Phase,16KA,50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Ammeter Meter.

Supply, Installation, Testing and commissioning of Office Building Common Load Panel LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Buttom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * Refer Electrical Main Single Line diagrams for panel details. Incomer: 200A,4P,MCCB with 25KA Breaking Capacity with thermal release with Overload and Short circuit protection - 1Nos Outgoing Feeders: 63A,4P,MCB with 10KA - 9Nos 25A,DP,MCB with 10KA - 4Nos 100A,4P,MCCB with 16KA Breaking Capacity with thermal release Overload and Short circuit protection - 1Nos Busbars Rating : 200A,3Phase,16KA,50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Multifunction Meter With RS-485 Supply, Installation, Testing and commissioning of Ventilation Panel

Supply, Installation, Testing and commissioning of Ventilation Panel LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Buttom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with With R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incomin feeders Should be with OV,UV& Earth leakage protection. * Refer Electrical Main Single Line diagrams for panel details. Incomer: 100A,4P,MCCB with 16KA Breaking Capacity with thermal release Overload and Short circuit protection - 1Nos Outgoing Feeders: 32A,4P,MCB with 10KA - 13Nos Busbars Rating : 125A,3Phase,16KA,50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Multifunction Meter With RS-485

Supply, Installation, Testing and commissioning of Plumbing Distribution Panel LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Bottom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * Refer Electrical Main Single Line diagrams for panel details. Incomer: 63A,4P,MCB with 10KA - 1Nos Outgoing Feeders: 32A,4P,MCB with 10KA - 6Nos Busbars Rating : 100A,3Phase,16KA,50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Multifunction Meter With RS-485

Project Common Load Panel (Fire + Non Fire) LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Bottom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * * Refer Electrical Main Single Line diagrams for panel details. Incomer: 400A,4P,MCCB with 36KA Breaking Capacity with thermal release with overload and short circuit protection - 1Nos Outgoing Feeders: 63A,4P,MCB with 10KA - 4Nos 320A,4P,MCCB with 36KA - 1Nos 250A,4P,MCCB with 25KA - 1Nos 100A,4P,MCCB with 16KA - 1Nos Busbars Rating : 500A,3Phase,25KA,50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Multifunction Meter With RS-485

S u p p lying and erecting 250 kVAr, 3 phase, 50 Hz., capacitor duty contactor with de-latching mechanism microprocessor APFC controller with MPP / APP type capacitor with 525 V and having minimum overcorrect capacity of 1.8 In, peak inrush current capacity 300 In and minimum life 150000 hours with , consisting of suitable steps of MPP / APP type capacitor units with detuned copper filter 7% reactors with circuit breaker as main incomer and MCCB for each branch protection, as per specification no CP-ED/APFC

Supplying and erecting mini feeder pillar triple pole with 300A FPMCCB as incomer and 3 outgoing circuits with HRC fuse base and cartridge of 100A consists of copper bus bar 500V 300A complete erected in 14 gauge CRCA sheet box with supporting angles, self-locks, gasket and slanting top to be erected on provided foundation as per specification no. SW-SWR/MFP

Staff Quarters Meter Panel LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Buttom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * Refer Electrical Main Single Line diagrams for panel details. Incomer: 200A,4P,MCCB with 16KA Breaking Capacity with thermal release with overload and short circuit protection - 1Nos Outgoing Feeders: 25A,DP,MCB with 10KA with Metering compartment- 3Nos 32A,DP,MCB with 10KA with Metering compartment- 24Nos 63A,4P,MCB with 10KA with Metering compartment- 1Nos Busbars Rating : 160A,3Phase,16KA,50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, MSEDCL Meter.

Building Common Load Panel LT Panel requirements * The Panel Should Be Mfg. From CPRI Approved Panel Manufacturer with IEC-61439 & CPWD Standard. * Panel With 14/16 SWG, 7 Tank Processed, Epoxy Powder Coated. * Cable Entry From Bottom & Out From Buttom Side Of Panel. * Bus bars shall be of copper only and sufficient cross-section so that a current density of 1.5Amp/sqmm is not exceeded at nominal current rating for (1000A/sq.inch) for copper bus bars. The minimum sizes of sections of bus bars are given in Table VI -CPWD Standard. * Each phase duly covered with Red, yellow, Blue and Black Colour Heat Shrink Sleeves. * The Panel Should be Should be Indoor Type & Floor Mountable with IP-42. * Name Tag Plates Should Be Provided As Per The Requirement. * Paint - Siemence Gray - Powder Coating. * The Schematic Drawing for the Above Panel should be get approved from appointed electrical consultant before manufacturing the Panel. * The Panel should be Inspected & Tested at Manufacturing Place before dispatch At Site from Electrical Consultant. *all feeders with R , Y , B Phase Indicating Lamp & MFM Meter compatible for BMS Monitoring . All Incoming feeders Should be with OV,UV& Earth leakage protection. * Refer Electrical Main Single Line diagrams for panel details. Incomer: 63A,4P, ATS with 16KA Breaking Capacity - 1Nos 63A,4P,MCCB with 16KA Breaking Capacity with thermal release- 1Nos Outgoing Feeders: 40A,TP,MCB with 10KA - 2Nos 32A,DP,MCB with 10KA - 2Nos 25A,DP,MCB with 10KA - 1Nos 32A,TP,MCB with 10KA - 3Nos Busbars Rating : 63A,3Phase,16KA,50Hz Cu. Busbar Metering R,Y,B, Trip Indication Lamp, Volt Meter, Multifunction Meter With RS-485

Supplying and erecting ON LOAD four pole automatic transfer switch suitable for 415V, 100A, 50 Hz, capacity with enclosure, automatic/manual inbuilt time delay, high transfer speed, excellent breaking capacity, superior making capacity, compact & light weight, erected on provided angle iron /GI frame and connected with provided leads complete.

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SPMCB of 12 ways, on iron /GI frame (horizontal busbar type) as per specification no.SW-SWR/MCBDB (4 Way TPN DB)

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SPMCB of 24 ways, on iron/ GI frame/wooden board.(horizontal busbar type) as per specification no. SW-SWR/MCBDB (8 Way TPN DB)

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SPMCB of 12 ways/phase (36 poles) on iron/ GI frame (horizontal busbar type) as per specification no. SW-SWR/MCBDB (12 Way TPN DB)

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SP / TP MCBs of 12 ways, on iron/ GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB (4 Way VTPN DB)

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SP / TP MCBs of 24 ways on iron/ GI frame (vertical busbar type) as per specification no. SW-SWR/MCBDB (8 Way VTPN DB)

Supplying & erecting triple pole and neutral distribution board (TPNDB) with door surface/ flush mounted SP / TP MCBs of 36 ways on iron/ GI frame (vertical busbar type) as per specification no. SW- WR/MCBDB (12 Way VTPN DB)

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 6 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB (8 Way SPN DB)

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 10 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB (12 Way SPN DB)

Supplying, fixing and commissioning 2 pole,RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6/10/16/20/25A, as per specification no SWRCCB/ RCBO

Supplying, fixing and commissioning 2 pole RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 32A/40A as per specification no SW-RCCB/RCBO

Supplying, fixing and commissioning 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6A/10A/16A/20A/25/A as per specification no SWRCCB/ RCBO

Supplying, fixing and commissioning 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 32A/40A as per specification no SW-RCCB/RCBO

Supplying, fixing and commissioning 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 63A as per specification no SW-RCCB/RCBO

Supplying, erecting & marking SPMCB 6A to 32A, C-series (for motor/power) in provided distribution board as per specification no. SW-SWR/MCB

Supplying, erecting & marking TPMCB 6 A to 32A in provided distribution board as per specification no. SW-SWR/MCB

Providing & erecting 4 Pole MCCB upto 100A, 415V, with short circuit rating 25 kA (Ics=100% of Icu ),adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB

Supplying & erecting original 1.25 mm CRCA sheet metal enclosures with 20A. 2 pin plug & earth socket and 20A. 3 pin plug top with 20A/30A single pole MCB complete erected on angle iron/ GI frame.

Supplying & erecting original 1.25 mm CRCA sheet metal enclosures with 30A, 3 pin plug & earth socket and 30 A 3 pin plug top with 30A triple pole MCB complete erected on angle iron/ GI frame.

Supplying, erecting & terminating XLPE armoured cable 3½ core 300 sq. mm. copper conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½core 240 sq. mm. copper conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 1100 V. 3½ core 185 sq. mm. copper conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 150 sq. mm. copper conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 120 sq. mm. aluminium conductor with continuous 12.97 sq. mm. (8 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 95 sq. mm. copper conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 70 sq. mm. copper conductor with continuous 8.35 sq. mm. (10 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 50 sq. mm. copper conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 35 sq. mm. copper conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 3½ core 25 sq. mm. copper conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/AL

Supplying, erecting & terminating XLPE armoured cable 4 core 4 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 4 core 6 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 4 core 10 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 4 core 16 sq. mm. copper conductor with continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 2 core 2.5 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 2 core 4 sq mm copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 2 core 6 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 200 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 300 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 400 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 500 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Providing & erecting Hot dipped galvanized cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) GI sheet of 150 mm width & 20 mm height complete with necessary hardware in approved manner.

Providing & erecting Hot dipped galvanized cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) GI sheet of 200 mm width & 20 mm height complete with necessary hardware in approved manner.

Providing & erecting Hot dipped galvanized cover suitable for perforated type cable tray manufactured from 18 swg (1.2 mm thick) GI sheet of 300 mm width & 20 mm height complete with necessary hardware in approved manner.

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Supplying & laying (including excavation) 15 cm dia RCC Hume pipe with coupling collar of standard thickness at required depth up to 90 cm below road / ground surface, for enclosing provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).

Supplying & laying (including excavation) 25 cm dia RCC Hume pipe of standard thickness at required depth up to 90 cms. below road / ground surface, for covering provided cable & necessary back filling with light ramming to make the road/ground surface as it was (Except bitumen carpet).

Making burnt brick masonry with 1:6 ratio cement concrete duly plastered including watering, streaking joint on exposed faces, rocking at joint on exposed faces and watering complete.

Supplying & erecting cast iron cable indicator plate buried along with route of cable for PVC / XLPE armoured cable as per specification no. CB-CIP

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no. EA-EP.

Supplying and erecting GI strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no EA-EP.

Supplying and erecting Annealed bare copper wire of high purity of different sizes used for earthing on wall with necessary copper clamps fixed on wall/cable/conduit with screws in an approved manner.

Supplying and erecting GI earth wire of high purity of different sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws in an approved manner.

Providing earthing with galvanized iron earth plate size 60 x 60 x 0.6 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover complete with all materials, testing & recording the results as per specification no. EA-EP

Providing earthing with copper earth plate size 60 x 60 x 0.315 cm with funnel with a wire mesh for watering and brick masonry block C.l. cover with minimum 25 kg Carbon based environment friendly back fill Ground Enhancing compound complete with all materials, testing & recording the results as per specification no ESE -LA

Point wiring for light/fan/bell hybrid type (Surface type under false ceiling and concealed type for drops & switch boards on walls) in min 20 mm PVC conduit / casing n capping with 1.5 sq.mm. (2+1E) FR grade copper wires, modular type switch, earthing and required accessories as per specification No: WGPW/ HW

Secondary point wiring for additional light/ bell point, concealed type in min 20 mm PVC conduit with 1.5 sq.mm. (2+1E) FR/FRLSH grade copper wires with required accessories as per specification No: WG-PW/CW

Point wiring in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR grade copper wire, flush type switch, earthing and required accessories as per specification No: WG-PW/SW

Secondary point wiring for additional light/ bell point in PVC trunking (casing-capping) with 1.5 sq.mm (2+1E) FR / FRLSH grade copper wire with required accessories as per specification No: WG-PW/SW

Supplying and erecting ISI mark modular type (two module) electronic step regulator for fan, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type blanking plate one module, duly erected on provided plate & box.

Supplying & erecting mains with 2x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW ( For Lights on MCB)

Supplying & erecting mains with 1x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW ( For Lights on MCB)

Supplying & erecting mains with 2x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying & erecting mains with 1x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG-MA/BW ( For Lights on MCB)

Supplying & erecting mains with 2x4 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying & erecting mains with 1x2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type switch 16A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type switch 16 / 20 A with indicator, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6A multi socket with safety shutterISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting modular type 3 pin 6 / 16A multi socket with safety shutter ISI mark approved make duly erected on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular double mounting plate 2 modules complete duly erected.

Supplying and erecting PVC Surface modular double mounting plate 3 modules complete duly erected.

Supplying and erecting PVC Surface modular double mounting plate 4 modules complete duly erected.

Supplying and erecting PVC Surface modular double mounting plate 6 modules complete duly erected.

Supplying and erecting PVC Surface modular double mounting plate 8 modules complete duly erected.

Supplying and erecting PVC Surface modular double mounting plate 12 modules complete duly erected.

Supplying and erecting PVC Surface modular double mounting plate 16/18 modules complete duly erected.

Supplying and erecting modular pop up Box 8 module erected with provided AV/ HDMI , RJ 45,6 A electrical sockets and switch on provided table .

Providing & erecting 4 Pole MCCB of 250A,415V capacity with short circuit rating 36 kA (Ics=100% of Icu) adjustable thermal (overload) setting and fixed magnetic setting with provided leads, provision for installation of shunt/ UV/ trip alarm contact and MCCB should have phase barriers both sides, in provided enclosure on iron /GI frame as per specification no. SW-SWR/MCCB (4 Pole MCCB of 250A)

Supplying and erecting SS enclosure for MCCB suitable for 125A to 200A MCCB complete.

Supplying and erecting luminous / modular type call bell indicator with plastic body, heavy duty coil and indicator lamp working on 230V A.C. supply with resetting arrangement complete erected on double wooden/ sunmica board

Supplying and erecting HMS PVC conduit 25 mm dia. with PVC accessories on wall /ceiling as per specification No: WG-MA/CON.

Supplying and erecting PVC box trunking of size 100x50 mm. with accessories on wall/ceiling as per specification No: WG-MA/BOX .

Supplying and erecting square / rectangular shaped CRCA /diecastcopper powder coated housing LED panel (slim edge-lit) light suitable for 25 to 32W with provision for plane front frame with translucent cover fixed to the housing complete.

Supplying and erecting LED square / circular 5 to 8W down lighter having pressure die-castcopper housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting LED square / circular 13 to 15W down lighter having pressure die-cast aluminum housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting LED square / circular 16 to 20W downlighter having pressure die-castcopper housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying & erecting LED 18W tube light fitting (4 feet) with polycarbonate housing, heat sink, integrated HF electronic driver complete.

Supplying & erecting LED 20W tube light fitting (4 feet) withcopper housing, heat sink, integrated HF electronic driver complete.

Supplying and erecting LED square / circular 9 to 12W down lighter having pressure die-castcopper housing, opal translucent cover, mounting arrangement with board for surface type or spring loaded mounting clips for flush type complete.

Supplying and erecting LED flexible strip light 5m length upto 25W conforming IP 65 of any colour with driver complete.

Supplying LED concealed type foot / step light with PVC body for indoor application suitable for upto 5 W LED including driver and erecting by making necessary arrangement/recess in wall to make it flush with surface

Supplying and erecting 2 light fancy wall bracket with arm fabricated from brass duly lacquered with suitable holder and fancy glass shade duly wired erected on wall with suitable size of polished wooden / laminated board.

Supplying & erecting suspension type decorative fitting with rise /fall arrangement, 1 light inside semi-circular metallic reflector with counterweight with guide pulley / spring buffer with work shop type copper flexible wire complete with necessary hook, if required.

Supplying and erecting Recess mounted 20W LED wall washers, tilted 70° outwards and swivels 360° to offer best illumination on the wall with any colour with driver complete. ( Including Compatible Driver)

Supplying and erecting cylindrical shaped integral decorative with high power 12W-16W LED bollard upto 1000mm with opal acrylic diffuser and IP65 protection on provided foundation complete.

Supplying and erecting Gate/garden light fitting with 300mm dia. glass bowl suitable for upto 12W LED lamp on provided pipe as per specification No. FG-ODF/GLT

Supplying and erecting decorative oval bulk head edge-lit 10W LED luminaire comprising of high brightness LED Fitting on provided PVC block / wooden board.

Supplying & erecting 10-12W, 230V integral type LED Lamp suitable for B-22/E-27 base.

Supplying and erecting fresh air cum exhaust fan of light duty250 V A.C. 50 cycles 225mm. 1400 RPM rust proof body & blades, wire mesh, duly erected in an approved manner.

Supplying and erecting five star rated energy saving Ceiling fan 230 V A.C. 50 cycles 1200 mm complete erected in position as per specification no. FG-FN/CF (900MMM 5Star 25No's)

Supplying and erecting blanking plate of suitable size on MCB DB complete.

Supplying and erecting of Lux level sensor light switch with auto dimming having a coverage of 6m dia, if mounted at 3.6 m with site adjustable off timing/ dimming and instant ON / OFF

Supplying and erecting of Occupancy sensor light switch having a coverage of 6m dia, if mounted at 3.6 m with site adjustable off timing and instant ON/OFF

Supplying & erecting on line UPS pure sine wave of 1kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins. battery backup, as per specification no. AP-UPS (UPS efficiency should be >94%)

upplying & erecting on line UPS pure sine wave of 2kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins. battery backup, as per specification no. AP-UPS (UPS efficiency should be >94%)

upplying & erecting on line UPS pure sine wave of 3kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins. battery backup, as per specification no. AP-UPS (UPS efficiency should be >94%)

upplying & erecting on line UPS pure sine wave of 5kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins. battery backup, as per specification no. AP-UPS (UPS efficiency should be >94%)

Supplying & erecting on line UPS pure sine wave of 15 kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins battery backup, as per specification no. AP-UPS (UPS efficiency should be >94%)

Supplying & erecting on line UPS pure sine wave of 20 kVA capacity complete with standard features, along with necessary SMF batteries for 30 mins battery backup, as per specification no. AP-UPS (UPS efficiency should be >94%)

Supplying and erecting ultra violet storage type water purifier ( RO+UV+UF) with softener for safe drinking water consisting of UV germicidal tube of 8W capacity choke made of copper wire and two indicator lamps with output of purified water 7 to 8 litre/min with activated carbon filter and softener operating on 230 V single phase A.C. supply.

Supplying and erecting storage type horizontal / vertical water heater 15 litres capacity with BEE 5 star rating high impact resistance engineering plastic body on wall / loft complete duly tested and marking sr. no. and date of erection. specification no. AP-WH/STWH

Supplying and erecting storage type horizontal / vertical water heater 25 litres capacity with BEE 5 star rating high impact resistance engineering plastic body on wall / loft complete duly tested and marking sr. no. and date of erection. specification no.AP-WH/STWH

Providing fibre reinforced pvc flexible pipe upto 1m length with brass locking nuts and washers and clips at both ends suitable for hot water and cold water both (1set of 2 nos) complete.

Providing & erecting 5 m high galvanised conical pole with foundation bolts having bottom dia. from 125 to 145 mm, top dia. from 65 to 75 mm on provided foundation as per specification no. OH-PL/CPL

Providing & erecting 6 m high galvanised conical pole with foundation bolts having bottom dia. from 135 to 160 mm, top dia. from 65 to 75 mm on provided foundation as per specification no. OH-PL/CPL.

Providing and erecting galvanised 1000mm single arm sword type bracket with FRP dome and ball as per specification no. OHPL/ PBKT

Providing and erecting galvanised 1000mm double arm sword type bracket with FRP dome and ball as per specification no. OHPL/ PBKT

Supplying and erecting LED street light fitting suitable for 20 to 25W, with PF > 0.95 class IP 65 and above housing of pressure die castcopper alloy and heat sink extrudedcopper complete as per specification No FG-ODF/FLS-2.

Supplying, installing, testing and commissioning solar street light pole comprising of 12W x 2 nos. LED fittings, 12V min. 100Ah maintenance free lithium battery, min. 120Wp SPV module, MS powder coated battery box weather proof, mounted on 75/80 mm dia. B-Grade GI pole of 6 m. height along with brackets, foundation, earthling and necessary accessories complete. Specification no. ESDSOL- STL

Making cement concrete foundation including excavation ( 45 x 45 x 120 ) cm deep in 1:3:6 cement concrete, 20 to 25 mm stone metal,(45 x 45 x 45) cm / 45 cm dia. x 45 cm height plinth duly plastered, with necessary curing and finishing complete. (for 6 m pole)

Supplying, erecting & terminating XLPE armoured cable 4 core 4 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying and laying (including excavation of suitable width & depth up to 90 cm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, to required depth complete.

Estimation No:- 121131-2 of 2019-20 Sub-Work No.2 Providing VRV Air Conditioning System, Earth Tunnel Cooling System,Radiant Cooling System to the State of Art Office Building and Campus (Staff Quarters Building,DG Bungalow and Guest House) For MEDA At- Aundh, Pune.

Supplying, erecting, testing and commissioning 18 HP,VRF / VRV air conditioning system, out door unit(ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalnt refrigerant, for cooling capacity delivering 100% at 47 deg. celcius and non stop cooling even at 56 deg. celsius and coefficient of performance (COP) not less than 3.28, modular type horizontal/vertical hot air discharge suitable for total piping length upto 1000 meter operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter/control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V ± 10%, 50 Hz, 3 phase power supply, internal copper refrigerant piping, internal wiring and first charge of refrigerant, etc. all housed in powder coated weather proof cabinet on provided angle iron frame or suitable foundation connected to the system in approved manner complete.

Supplying, erecting, testing and commissioning 20 HP VRF / VRV air conditioning system, out door unit(ODU) complying type-IV OEM standards working on HFC free refrigerant R410A or other required/suitable green equivalent refrigerant, for cooling capacity delivering 100% at 47 deg. celcius and non stop cooling even at 56 deg. celsius and coefficient of performance (COP) not less than 3.28, modular type horizontal/vertical hot air dischargesuitable for total piping length upto 1000 metre operation in cooling mode with inverter based VRF/VRV technology microprocessor based control compressor starter/control panel complete with scroll compressor, air cooled anti corrosive copper condenser coil of suitable shape for increasing maximum heat transfer area, built in oil separator, accumulator and oil receiver, copper tube aluminium fin air cooled condenser, condenser fan with motor suitable for 415V ± 10%, 50 Hz, 3 phase power supply, internal copper refrigerant piping, internal wiring and first charge of refrigerant, etc. all housed in powder coated weather proof cabinet on provided angle iron frame or suitable foundation connected to the system in approved manner complete.

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 2.6TR ( 918 cfm ) to 2.8TR ( 1100 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. Indoor Units complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete. Capacity - 2.55 TR Cassette unit with chordless remote controller

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 2.6TR ( 918 cfm ) to 2.8TR ( 1100 cfm ) having EER as per BEE standards and specificatio port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete. 2.00 TR Cassette unit with chordless remote controller

Supply, installation, testing and commissioning of VRF/VRV based ceiling suspended 4 Way cassette indor unit (IDU) compact / standard size of nominal cooling capacity 1.0TR ( 441 cfm ) / 1.3TR ( 512 cfm ) having EER as per BEE standards and specifications, suitable as per site requirement with swing louvers and adjustable blades from sides. Indoor Units complete with in-built drainage arrangements, fan, refrigerant liquid and refrigerant piping, cordless remote control, and fresh air port etc. IDU shall have anticorrosive coating suitable for coastal area complete in all respects, to operate on 1-phase, 230V, 50Hz, AC input supply, consisting with any additional refrigerant and oil charge as per requirement during installation and connected to the system complete. 1.28 TR Cassette unit with chordless remote controller

Supply, installation, testing and commissioning of VRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 1.8TR (594 cfm) to 2.2TR (655 cfm) having EER as per BEE standards and specifications with multiple speed vaporator fan with motor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitable mounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete. (Capacity- 2 TR)

Supply, installation, testing and commissioning ofVRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 1.3TR (421 cfm) to 1.7TR (586 cfm) having EER as per BEE standards and specifications with multiple speed evaporator fan withmotor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitable mounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete.(Capacity- 1.59 TR)

Supply, installation, testing and commissioning ofVRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 1.3TR (421 cfm) to 1.7TR (586 cfm) having EER as per BEE standards and specifications with multiple speed evaporator fan withmotor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitable mounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete. (Capacity-1.28 TR)

Supply, installation, testing and commissioning ofVRF/VRV based Hi-wall type indoor unit (IDU) of nominal cooling capacity 1.0TR (358 cfm) to 1.25TR (417 cfm) having EER as per BEE standards and specifications with multiple speed evaporator fan withmotor, copper tube aluminium fin evaporator coil, washable air filter, insulated drain tray, expansion device, cordless remote control with necessary controls, with 3-core copper flexible cord of required length and electrical terminal to receive power supply, etc. IDU shall have anti-corrosive coating suitable for coastal area. Unit shall be suitable for indoor wall mounting, having an electronic control console, provided with suitable mounting brackets with any additional refrigerant and oil charge as per the requirement during installation, connected to the system complete.(Capacity-1 TR)

Supplying and installation of high pressure grade required size copper connection Y or T- Joints / refnet for liquid and suction line complete erected on wall/ceiling with supports/raceways, Nitrile rubber insulation, painting etc.with brazing and testing for leakages confirming the normal operation of the VRV / VRF air conditioning system.

Supplying, erecting, testing and commissioning centralised programmable remote contol panel (HMI) touch manager controls minimum 16 system of minimum 64ODU's can be controlled and up to 992 IDU's can beindividually mounted and controlled indoor units havingminimum 200 mm size colourLCD touch panel, yearly schedule, power proportional distribution function,temperature limitation, history function complete erected on wall with an arrangement to integrate with provided fire alarm system.

Supply & Installation of Occupancy Sensors having Coverage Of 6m dia if mounted at 3.6m wih site atdjustable off timing and instant ON/OFF

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 41.3 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessarysupports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along withapplication of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultraviolet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 34.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 28.6 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 22.2 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 19.1 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 15.9 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 12.7 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 9.5 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

Supplying, laying / fixing, testing and commissioning of appropriate nominal refrigerant copper pipe of 6.4 mm dia (OD) for liquid line / suction line supply and return piping of suitable gauge ( hard drawn copper pipe for liquid main line and for refrigerant ) along with necessary supports, hangers, clamps, vibration isolators and fittings such as bends, tees, valves, gauges, strainers with insulation of 19 mm thick elastomeric nitrile rubber along with application of multicoating suitable for use with VRV / VRF piping for protection against mechanical damages, fungal growth, flame spread, water permeance and ultra violet radiations complete with OEM standards of VRV / VRF air conditioning system.

SITC of Insulated Hard PVC drain Piping with 9 mm Tubular Insulation with supporting clamps 18 mm

SITC of Insulated Hard PVC drain Piping with 9 mm Tubular Insulation with supporting clamps 25 mm

SITC of Insulated Hard PVC drain Piping with 9 mm Tubular Insulation with supporting clamps 32 mm

SITC of Insulated Hard PVC drain Piping with 9 mm Tubular Insulation with supporting clamps SITC of Insulated Hard PVC drain Piping with 9 mm Tubular Insulation with supporting clamps 50 mm

Supply Installation & Testing of Control Cabling from indoor to outdoor unit. Supplying, installing, testing and commissioning FR, XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling complete as per specification no. CBLT/CU

Supply Installation & Testing of armoured cu.power cabling Power cable for IDU - Supplying, erecting & terminating XLPE armoured cable 3 core2.5 sq. mm. copper conductor continuous 5.48 sq. mm. (12SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU

Power cable for ODU -4c x 10 sq.mmSupplying, erecting & terminating XLPE armoured cable 4 core 10sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG)G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no.CBLT/CU.

Supply & installation of Isolator switch of suitable size in weatherproof enclosure conforming to IP55 (to be located in the vicinity of outdoor unit for isolation). 18 HP

Supply & installation of Isolator switch of suitable size in weatherproof enclosure conforming to IP55 (to be located in the vicinity of outdoor unit for isolation). 20 HP

Supply Installation & Testing of drain Pump for High wall units with specifications like thremal protection,inbuilt non return valve,low noise operational etc.

Providing vaccumising the airconditioner system to 200micron and charging with R-410A/R32 refrigerant for air conditioning unit.

Supply installation testing and commissioning of outdoor Air processing unit (TFA). Units shall be ceiling mounted, with high performance filter, wired remot controller. These units are connected to VRV systemTFA-336 CFM Fan Capacity 275 Pa static pressure

Supply installation testing and commissioning of outdoor Air processing unit (TFA). Units shall be ceiling mounted, with high performance filter, wired remot controller. These units are connected to VRV systemTFA-635 CFM Fan Capacity 275 Pa static pressure

Supply installation testing and commissioning of outdoor Air processing unit (TFA). Units shall be ceiling mounted, with high performance filter, wired remot controller. These units are connected to VRV system TFA-988 CFM Fan Capacity 275 Pa static pressure

Supply installation testing and commissioning of outdoor Air processing unit (TFA). Units shall be ceiling mounted, with high performance filter, wired remot controller. These units are connected to VRV systemTFA-1235 CFM Fan Capacity 275 Pa static pressure

Supply , fabrication, erection and commissioning of Inline Belt driven Cabinet Fan, construction in Galvanised sheet steel, DIDW centrifugal fan, Flanged inlet & outlet & with EU-4 filter & with IE-4 motor Capacity - 3450 CFM / Static Pressure - 40 mmwg / Load - 1.5 kw

Supply , fabrication, erection and commissioning of Inline Belt driven Cabinet Fan, construction in Galvanised sheet steel, DIDW centrifugal fan, Flanged inlet & outlet & with EU-4 filter & with IE-4 motor Capacity - 4450 CFM / Static Pressure - 40 mmwg / Load - 2.2 kw

Supply, Installation of Extruded Aluminum Supply Air Grilles with zero deflection. Grill Size-200x200

MS painted Structural Steel for supports for Ducting only. Two coats of red oxide and enamel paint to be applied. Angles, channel support.

GI threaded rods, anchor fasteners etc for ducting.

Providing adhesive thermal insulation for supply /return air duct (Supply, installation, testing & commissioning of Class 'O' elastomeric nitrile rubber insulation / cross linked polyethylene, for ducting. Insulation to be provided complete for fittings, adhesive (elbows, taper, flanges etc.) etc all as per specifications) with 19 mm nitrile rubber insulation having R-value as per the prevailing provisions in ECBC-2007.

VOLUME CONTROL DAMPER Supply, installation, testing and commissioning of volume control box with collor for control damper of required sizes in GI construction complete with operating mechanism, mounting arrangement, rubber refrigerant kits etc. complete.

Supply & Installation of controller of CFM.35-100 CFM

Supply & Installation of controller of 150 CFM

Flexible Ducting: Supplying and erecting circular flexible / rigid PVC pipe duct of size 100 mm dia, 4 mm thickness with required couplers, reducers, T-joints, Y-joints elbows and necessary supports etc with sealing complete with provided control/ air flow regulating valves / dampers, filters at position

Supplying and erecting circular flexible / rigid PVC pipe duct of size 150 mm dia, 4 mm thickness with required couplers, reducers, T-joints, Y-joints elbows and necessary supports etc with sealing complete with provided control/ air flow regulating valves / dampers, filters at position

Supplying and erecting circular flexible / rigid PVC pipe duct of size 200 mm dia, 4 mm thickness with required couplers, reducers, T-joints, Y-joints elbows and necessary supports etc with sealing complete with provided control/ air flow regulating valves / dampers, filters at position

Supply, Installation, Testing & Commissioning of Radient Cooling as per below description Primary Pipings (Gypsum Ceiling): Giacoqest pipe in cross linked polyethylene with ANTI-OXYGEN BARRIER Insulating panel in expanded polystyrene. Density 30 kg/m3. Thermal resistance 0,65 m2 K/W. Compression resistance to 10% crush 200 kPa. Joint combined with a thermoconductor profile constituted by an aluminium foil 0,3 mm thickness Insulating header panels for the passage of the service pipe lines and the support of the circuit bending. Expanded polystyrene plates. Density 40 kg/m3. Thermal resistance 0,50 m2 K/W. Gypsum Board (6'X4') 12.5 MM thick U shaped perimeter profile in zinc coated steel. Primary carrying element U shaped, in zinc coated steel for the implementation of a reduced false ceiling on double metallic frame. The profile is prearranged for the snap connection of C shaped secondary profiles, by means of appropriate shaped hooks C shaped secondary carrying element in zinc coated steel for the implementation of a reduced false ceiling on single or double metallic frame through snap connection on U shaped primary profiles. Fixing Clip, Supporting Channel with accessory like nut washer rod Secondary Piping: DN32 modular manifold for use on fow, with bayonet connection, fow meter, balancing lockshield valve with mechanical memory and adaptor connection (Single Manifold) DN32 modular manifold for use on fow, with bayonet connection, fow meter, balancing lockshield valve with mechanical memory and adaptor connection (End Manifold) Pre-assembled manifolds Distribution, Plastic pipe adaptor Box For Collectors brackets, Multifunction valves with Ball shut-off valve,Automatic air vent valve , Valve for the system charge and discharge,Contact thermometer & Inlet of the immersion temperature sensor ø 6 mm Kit for connecting Return manifold to Supply manifold Controls: Three-way mixing valve with piston obturator, female-female connection tee joint Actuator for K297 mixing valve. Possibility of automatic command in combination with Giacomini thermoregulation Immersion delivery temperature probe (passive type). Measuring range -50/105 °C. Cable length 6 m. Bulb diameter 6 mm

Supply, Installation, Testing & Commissioning of Inverter Air-Cooled Scroll Mini Chiller - Cooling only (R407C / R410A), with scroll Compressors & Moto. Mini chiller is fully integrated and equipped with key hydronic components such as Multistage End Suction water Pump, Brazed Plate Heat Exchanger, Diaphragm Expansion Tank and with Filter Dryer, Factory Precharged Refrigerant, Water Storage Tank, Serviceability & Error Code for ease of troubleshooting. Chiller shalll be equiped with Microprocessor controller that will control and regulate the operation of the unit and will provide protection to the chiller, machine mounted Chiller control panel to control chiller operation. Safety protections such as High & Low pressure switches, Anti freeze protection sensor, Discharge Temperature Sensor, Over Pressure Relief Valve, Water PressureDifferential Switch, Anti-freeze heater on heat exchanger, Compressor Water pump & Fan Moto Overload protector. Motor shall be suitable for 415±10% 50 cycles. 3 phase AC supply. Capacity:- 9.6TR Chiller Water IN 20°C Chilled Water OUT 15°C

Supply, laying/fixing, testing and commissioning of 50mm dia piping of chilled water MS ERW heavy "C" class piping with necessary clamps, supports, hangers and fittings such as bends, tees, reducers etc. (but excluding valves, strainers, gauges, etc.) duly insulated with Armaflex/Approved Equivalent closed-cell elastomaric Nitrile Rubber insulation of 40-60 kg/cumt density with Aluminium cladding. Brush & clean pipe surface before applying insulation. Stick insulation material using a thin film of manufacturer-recommended adhesive on both pipe and insulation. Seal all joints air-tight. Provide minimum 25mm thick insulation up to 40 mm dia piping, and minimum 32 mm thick insulation from 50 to 150mm dia and above piping. All fittings/valves shall be insulated with the same thickness of insulation material

Supply, laying/fixing, testing and commissioning of 32 mm dia piping of chilled water MS ERW heavy "C" class piping with necessary clamps, supports, hangers and fittings such as bends, tees, reducers etc. (but excluding valves, strainers, gauges, etc.) duly insulated with Armaflex/Approved Equivalent closed-cell elastomaric Nitrile Rubber insulation of 40-60 kg/cumt density with Aluminium cladding. Brush & clean pipe surface before applying insulation. Stick insulation material using a thin film of manufacturer-recommended adhesive on both pipe and insulation. Seal all joints air-tight. Provide minimum 25mm thick insulation up to 40 mm dia piping, and minimum 32 mm thick insulation from 50 to 150mm dia and above piping. All fittings/valves shall be insulated with the same thickness of insulation material

Supply, laying/fixing, testing and commissioning of 25mm dia piping of chilled water MS ERW heavy "C" class piping with necessary clamps, supports, hangers and fittings such as bends, tees, reducers etc. (but excluding valves, strainers, gauges, etc.) duly insulated with Armaflex/Approved Equivalent closed-cell elastomaric Nitrile Rubber insulation of 40-60 kg/cumt density with Aluminium cladding. Brush & clean pipe surface before applying insulation. Stick insulation material using a thin film of manufacturer-recommended adhesive on both pipe and insulation. Seal all joints air-tight. Provide minimum 25mm thick insulation up to 40 mm dia piping, and minimum 32 mm thick insulation from 50 to 150mm dia and above piping. All fittings/valves shall be insulated with the same thickness of insulation material.

Supply Installation Testing & Commissioning of ButterflyValve,cast iron,flange type,PN16 rating, 50 mm size Butterfly valve

Supply Installation Testing & Commissioning of Ball Valve,brass iron,screwed type,PN10 rating, 32mm size Ball Valve

Supply Installation Testing & Commissioning of Ball Valve,brass iron,screwed type,PN10 rating, 25mm size Ball Valve

Supply Installation Testing & Commissioning of Y strainer, cast steel,screwed type,mesh 2mm perforation x 24 gauge 50mm size

Supply Installation Testing & Commissioning of Balancing Valve,cast bronze,screwed type,PN16 rating,max flow temp 200 deg C 50mm size Balancing Valve

Supply Installation Testing & Commissioning of Non Return Valve ( Check Valve) ,bronze,screwed type,PN16 rating,max working temp80 deg C, 25mm size Non-Return Valves( For Make Up Line)

Supply Installation Testing & Commissioning of Differential Pressure Bypass Valve,cast iron,flange type,PN16 rating 50mm size Differential pressure Bypass Valves

Supply Installation Testing & Commissioning of Thermometer, 0 to 50deg C,150mm stem length,100mm dia,1/2 inch BSP

Supplying and installing pressure gauge of 100 mm dia., 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm dia. pad cock valve, and G.I. pipe, elbow etc. complete as per specification no. FF-FFA/PG

Supply Installation Testing & Commissioning of Flexible Connection bellows, manufactured with a high quality EPDM Pipe flexible connection at chillers & expansion joints, 50 NB

Descaling Plug for Chiller

Treated Fresh Air unit : Supply installation testing and commissioning of double skin air handling unit in 43±2 mm thick puf insulation complete with thremal break profile ,22 G inside GI sheet and 22 G GI outside sheet with precoating and with flowing section & with IE-4 motor TFA frame work shall be of Anodized Aluminum construction with thermal break profile & internal coving Pre filter section with G-5 filter rating. and PVC ports for pressure drop measurement as per specifications Complete with fan section with DIDW backward curved centrifugal fan,drive motors and accessories. DX Coil section with coil ( 8 row deep) with interlaced type 2-circuit arrangement Marine light with limit switch across fan section door shall be provided with switch for marine light on / off outside the unit. Opposed blade low leakage extruded aluminum volume control dampers For Supply & return air to be Provided SS 304 drain pan,Cable entry for motor and sufficient distance between all section All Cable & pipes should be Roxtec flexible sealed type. Antivibration Rubbber Pads for Mounting TFAs Considered fan & coil capacity should be 10% higher than given capacity TFA-2832 CFM Fan Capacity / 17 TR / 65 mmwg static pressure

Air Cooled Condensing Unit for TFA : Air-cooled condensing units of specified tonnage capacity, each complete with the following major items: Scroll compressor/s with accessories, Air-cooled condenser/s with accessories; having high heat-transfer efficiency seamless copper tube coils with aluminium fins, low-noise direct-driven propeller fans, TEFC motors, etc., Controls, safety cutouts including high & low pressure cutouts, oil safety cutout, adjustable thermostatic control of room temperature at RA level; refrigerant filters & dryers, copper control tubing, expansion device, etc. (Expansion device for cooling coil must be designed & supplied by Cond. Unit mfr), Condensing unit stand base frame, made from galvanised steel sections with epoxy/powder coating, Rubber vibration isolators & mounting arrangement for vibration-free operation of all equipment, Refrigerant & oil 17 TR Condensing Units with Twin compressor

Supply, Installation of Extruded Aluminum Supply Air Grilles with zero deflection. Grill Size-500x200

Supply, Installation, testing and commissioing of Inline cabinet Fan along with insect screen in SS 304 construction and gravity louversat inlet with necessary supporting arrangement. 3178 Cfm , 1.10 kw & with IE-4 motor

Sheet metal work & ducting : Supply, Installation & testing of Galvanized Sheet (GI) Ducting class VIII as per IS-277 with M.S. Angle Flange, turning vanes, with proper duct sealing etc. with RTV duct Sealant, complete with supports, Pressure tested as per specification Ducting shall be factory fabricated in L/ box shape and assembled at site with MS angle flanges painted all as per specifications. Primary and secondary support required shall be provided by vendor and cost for the same to be included in the unit rate. (MS structure separately given). Note: Vendor to consider necessary identification Arrow for supply air of appropriate sizes and color. Plenum Box 20 Gauge

Ducting supports : Supply, installation, testing & commissioning of Class 'O' elastomeric nitrile rubber insulation / cross linked polyethylene, for ducting. Insulation to be provided complete for fittings, adhesive (elbows, taper, flanges etc.) etc all as per specifications 13 mm thickness with Al.cladding 26 G for exposed duct.

Supply Air Duct insulation by 9 mm thick insulation.

GRIILS WITH DAMPER: Supply, Installation of Extruded Aluminum Supply Air Grilles with Damper Grill Size-300 X 300

ELECTRICAL STARTER FOR EAT FAN : Supplying and erecting D.O.L. Starter 400V. 3 phase, 50 cycles with no volt coil and overload element with necessary materials and connected to supply upto 7.5 H.P.

2- STAGE EVAPORATIVE COOLING UNIT (DOUBLE SKIN,25+/- 2 mm THICK.): Supply,Installation,Testing and commissioning of factory fabricated , Two Stage Evaporative Cooling units suitable for out door mounting condition complete with Centrifugal backward curved DIDW fan section,indirect evaporative section, Direct Evaporative Section, and pressurized flow via a heavy duty piping system for food grade anti-bacterial 12"thick pad and media water distribution, with drain connection with drain valve, for quick fill with valves, overflow connection, Y strainers and necessary fittings . The sump tank shall be of 2 mm stainless steel (with necessary both way slope) construction with a float valve arrangement.Unit shall have with Pre-filter of 10 microns at the air inlet side with indication meter shall be provided for Filter Choking Status. UV filtration systems should be incorporated to ensure optimum cleanliness of the water.All unit shall have individual access door for each indvidual section and with Electrical panel. Whole 2 stage evaporator units shall be made up of individual sections with independent access door for independent entry 2 stage evaporative cooling unit shall be consists of panels with the thickness of 25+/-2 mm of double skin type with food grade type insulation Fan shall be backward curved DIDW type with IE-4 motor with minimum efficiency 90 % with Fan total efficiency should be minimum 75 %. 2 stage evaporative cooling unit sump shall be of SS body with minimum thickness 2 mm Make up water connection shall be provided with float valve Water pumps required shall be of self priming Monoblock type (Wilo, grundfoss,equivalent make only) with mechanical seal . Pump to be installed outside the 2 Stage evaporative cooling unit Water Pads shall be of food grade anti-bacteria type strictly. Provision of GI partitions duly reinforced at intake side and louvers with bird-screen fabric filters and drift eliminators for all AW unit. (Foundation support for 2 Stage evaporative cooling unit is not in scope (RCC blocks)). 13000 cfm @ 65 mm Static pressure. Approximate water consumption is 845 ltr/ hr.

SHEET METAL WORK & DUCTING : Supply, Installation & testing of Galvanized Sheet (GI) Ducting class VIII as per IS-277with M.S. Angle Flange, turning vanes, with proper duct sealing etc. with RTV duct Sealant, complete with supports, Pressure tested as per specification. Ducting shall be factory fabricated in L/ box shape and assembled at site with MS angle flanges painted all as per specifications. Primary and secondary support required shall be provided by vendor and cost for the same to be included in the unit rate. 24 Gauge

Supply, Installation & testing of Galvanized Sheet (GI) Ducting class VIII as per IS-277with M.S. Angle Flange, turning vanes, with proper duct sealing etc. with RTV duct Sealant, complete with supports, Pressure tested as per specification. Ducting shall be factory fabricated in L/ box shape and assembled at site with MS angle flanges painted all as per specifications. Primary and secondary support required shall be provided by vendor and cost for the same to be included in the unit rate. 22 Gauge

Supply, Installation & testing of Galvanized Sheet (GI) Ducting class VIII as per IS-277with M.S. Angle Flange, turning vanes, with proper duct sealing etc. with RTV duct Sealant, complete with supports, Pressure tested as per specification. Ducting shall be factory fabricated in L/ box shape and assembled at site with MS angle flanges painted all as per specifications. Primary and secondary support required shall be provided by vendor and cost for the same to be included in the unit rate 18 Gauge

DUCTING INSULATION : Supply, installation, testing & commissioning of Class 'O' elastomeric nitrile rubber insulation / cross linked polyethylene, for ducting. Insulation to be provided complete for fittings, adhesive (elbows, taper, flanges etc.) etc all as per specifications: 13 mm thickness with Al.cladding 26 G for exposed duct.

Supply, installation, testing & commissioning of Class 'O' elastomeric nitrile rubber insulation / cross linked polyethylene, for ducting. Insulation to be provided complete for fittings, adhesive (elbows, taper, flanges etc.) etc all as per specifications.: 9 mm thickness with Al. Foil for inside duct.

ACOUSTIC INSULATION : Supplying & Installation of 15mm thick Armasound for Acoustic insulation of Ducting

Supply, Installation of Extruded Aluminum Supply Air Grilles with zero deflection.Size-900x400

Providing & erecting Hot dipped galvanized ladder type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 150 mm width & 100 mm height comprising all required standard accessories.

Providing & erecting Hot dipped galvanized ladder type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 300 mm width & 100 mm height comprising all required standard accessories.

Labour charges of Commissioning - Air balancing of entire system. NOTE : - For fire protection the electrical panel of evaporative unit to be interlocked with the fire panel, in case of fire the motor and pump of evaporative system will shutdown

From PCC Panel to Chiller Panel:. Supplying, erecting & terminating XLPE armoured cable 4 core 16sq. mm. copper conductor with continuous 5.48 sq. mm. (12SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU

From PCC Panel to TFA Unit:. Supplying, erecting & terminating XLPE armoured cable 4 core 4sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU.

Supplying and erecting GI earth wire of high purity of different sizes used for earthing or any other purposes on wall with necessary G. I. Clamps fixed on wall/cable/ conduit with screws in an approved manner.

Suppling and erecting GI Strip of required size used for earthing on wall and/or any other purpose with necessary GI clamps fixed on wall painted with insulating and non corrosive bond in an approved manner with joints required. As per specifiction No. EA-EP 32 X 3 mm G.I. STRIP (2 Strips).

BASEMENT VENTILATION : JET FANS: Supply, Installation, Testing & Commissioning of Induced jet fan (Dual Speed Fan), Ceiling Mounted Single Skin GSS 220 GSM Zinc coating with backward curved MS impeller Powder coated. Units Complete with supports, Mild Steel Mounting Frame, Fan section with casing made of Galvanized Steel, Motors shall be dual speed Class H insulation Smoke venting Complete Fan shall as per BS EN 12101-3:2002 Certified by TUV SUD PSB. Fan shall be Statically & Dynamically Balanced Upto G2.5 Grade. The Fan Shall be AMCA Certified For Air & Sound Performance 6480 / 3240 CMH

FRESH AIR FAN : Supply, installing, testing, commissioning of Fresh Air fan of Tube Axial/ Vane Axial type (Single Speed) as per technical specification and drawing. Fan speed shall not exceed 1450 RPM. IE4 Motor with class F isulation. All unit shall be suitable for outdoor installation, Mounting feet, Spring type vibration isolator, MS Powder coated Protectin net on free discharge side, Heavy duty flexible double layer canvas connection. Fan GAD to be submited for confirmation on fan mounting (Floor mounted). Capacity: 13248 CFM/ 0.75 Inch WC TSP

EXHAUST AIR FAN : Supply, installing, testing, commissioning & handing over of Exhaust fan of Tube Axial/ Vane Axial type (Single Speed) as per technical specification and drawing. Fan speed shall not exceed 1450 RPM (for Normal as well as Fire mode application). With I 4 Motor. with class H isulation. Fan shall be fire rated at 250°C for 120 minutes. All unit shall be suitable for outdoor installation, Mounting feet, Spring type vibration isolator, MS Powder coated Protectin net on free suction, Heavy duty flexible double layer canvas connection. Fan GAD to be submited for confirmation on fan mounting ( Floor mounted ).: Capacity: 26496 CFM/ 0.75 Inch WC TSP on Basement lvl (Normal + Fire Mode & fire Mode Exhaust)

CO Sensor - Analog type matching the technical Specification

CFD (Computational Fluid Dynamics) Analysis

Supply, fabrication, Installation, and testing of sheet metal ducts having minimum 120 GSM as per IS-277 complete with all accessories like flanges, all necessary MS supports, suspension rods , anchor bolts, GI bolts & nuts, adjustable splitter, guide vanes including air balancing with necessary connections etc., in accordance with the approved shop drawings and as per the specifications : 20 G galvanized sheet steel

Supply and Installation of GSS Louvers with bird screen, adjustable damper for fresh air and without damper for exhaust air complete with aluminum wire mesh bird screen in accordance with the approved shop drawings and specifications.: For Exhaust Air

VENTILATION LOGIC CONTROL PLC PANEL to Control Start/Stop & speed change in all fans in basement including Jet Fans, fans from Low to high speed based on the CO Level in the Basement.All these fans should also be SWITCHED on in full speed incase of receipt of FIRE Signal. The Logical Operation of pollution mode and FIRE mode is desired from PLC. Vendor Should submit SLD and GA drawings for Consultants approval. Compartmentalized Electrical MCC Panel as per IS standard 8623 with Protection Class of IP 42 and Fault level of 16kA. The panel made out of 14 SWG CRCA sheet finished with Siemens Grey Painting. The Panel consists 100A FP MCCB Incomer from Fire Emergency panel. 32A-9No's Outgoing Feeders along with Starters for Jet Fans, 25A FP MCB -4No's Fresh Air Fan, Normal Mode Fan & Fire Mode Fan with 3 nos. spare feeders, Metering with RS 485 LM, Indication Lamps, top cable entry, aluminium bus bar and custom built PLC logic controller with necessary control wiring etc. Each Feeder shall have FP MCB, two Starters and indication lamps, toggle switch for two speed operations and Electrical interlock for two speed functions. It Should control the JET Fans for demand ventilation with a Logic.

From Panel to Fan motor.: Supplying, erecting & terminating XLPE armoured cable 3 core 6sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU.

From Panel to Fan motor.: Supplying, erecting & terminating XLPE armoured cable 3 core 4sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/trusses/ pole or laid in provided trench/ pipe as per specification no.CB-LT/CU.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

STAIRCASE PRESSURIZATION FAN : SITC of axial flow fans with squirrel cage TEFC, 415± 10% volts, 50 cycles, 3 phase AC power supply, IP55, S1 duty, IS325, with IE-4 motor, class F insulation direct driven motor. Fan should be properly supported with MS frame, vibration isolators, flexible canvas, Bird mesh at suction side of fan, leak proof ducting connection with civil plenum with properly grouted M.S angles. MS structure should be painted with epoxy paint. Fans shall be safely stored an made lifting, shifting, assembly, making necessary arrangement for mounting Capacity: 17715 CFM/ 30 mmwc

Pressure Relief Damper

SITC of DP switch / sensor to maintain 50 Pa. at staircase.

AIR DISTRIBUTION : SITC of Site fabricated GSS Ducting Class VIII 120 GSM as per IS-277 with GI slotted C channel support, GI full threaded rod, double check nut washers system as specified in technical specification: 22 Gauge

Electrical Control Panel : SITC of Star delta starter panel with on off push button, on/off/trip indicators, NO/NC potential free contacts for BMS/integration with building Fire Fighting system, manual reset overload relays. Starter panel should be provided with auto manual toggle switch & facility to operate on remote signal from smoke control panel.

SITC of Armoured / flexible Copper cabling for DP switch/sensor including terminations. All Cables should be XLPE type : 2Core X 1Sqmm PVC flexible cable with conduit. (for DP switch/sensor)

LIFT WELL PRESSURIZATION FAN : SITC of axial flow fans with squirrel cage TEFC, 415± 10% volts, 50 cycles, 3 phase AC power supply, IP55, S1 duty, IS325, with IE-4 motor, class F insulation direct driven motor. Fan should be properly supported with MS frame, vibration isolators, flexible canvas, Bird mesh at suction side of fan, 16G GI motorised Volume control damper at the inlet, & leak proof ducting connection with civil plenum with properly grouted M.S angles. MS structure should be painted with epoxy paint.Fans shall be safely stored an made lifting, shifting, assembly, making necessary arrangement for mounting : Capacity: 17411 CFM/ 30 mmwc

Supplying, installing, testing and commissioning split type variable speed inverter technology room Air conditioning unit 2 TR capacity having ISEER minimum 4.50 suitable to operate on 250V, 50 cycles, A.C. supply having 1 no. of air handling unit hi-wall/ floor mounting type complete with Refrigerants R410 A /R32 and copper condenser at position. specification no. APAC/ SAC

Supplying, installing, testing and commissioning split type variable speed Inverter technology room Air conditioning unit 1.5 TR capacity having ISEER minimum 4.50 suitable to operate on250V, 50 cycles, A.C. supply having 1 no of air handling unit hiwall / floor mounting type complete with refrigerant R410 A/R32 and copper condensor at position. specification no.APAC/ SAC

Supplying & erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 12 mm complete.

Supplying & erecting soft drawn copper pipe suitable for refrigeration system having 22 SWG thickness and inner dia / size 16 mm complete..

Supplying and erecting 12/16 mm (ID/OD) polyethylene composite pipe duly joined by compression/crimp fitted accessories, with internal as well as external end sealing arrangement for solar water heater system complete. Specification no. (ESD-HWP/PCP)

Supplying and erecting 16/20 mm (ID/OD) polyethylene composite pipe duly joined by compression/crimp fitted accessories, with internal as well as external end sealing arrangement for solar water heater system complete. Specification no. (ESD-HWP/PCP)

Supplying & erecting HMS P.V.C. conduit 25 mm. dia. With necessary accessories in wall/floor with chiselling appropriately as per specification No: WG-MA/CC.

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Estimation No:-Sub work No-3 Providing Fire Fighting and Fire alarm System to the State of Art Office Building and Campus (Staff Quarters Building DG Bungalow and Guest House) For MEDA At-Aundh ,Pune

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 25 mm dia with necessary fittings as per specification no.FF-PP

Supplying and erecting ISI mark GI pipe 32 mm. dia ‘C” class at position with accessories complete. Specification no. CW-PLB/GP.

Supplying and erecting ISI mark GI pipe 40 mm. dia ‘C” class at position with accessories complete. Specification no. CW-PLB/GP.

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 50 mm dia with necessary fittings as per specification No. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 80 mm dia with necessary fittings as per specification No. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 100 mm dia with necessary fittings as per specification no. FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 150 mm dia with necessary fittings as per specification no.FF-PP

Supplying and installing G.I.pipe above ground of ‘C’ class ERW of size 200 mm dia with necessary fittings as per specification no.FF-PP

Supplying and installing cast iron double flange sluice valve 100 mm dia. as per specification No.FF-VL/SV

Supplying and installing cast iron double flange sluice valve 150 mm dia. as per specification No. FF-VL/SV

Supplying & erecting cast iron double flange butterfly valve of size 75/80 mm dia. complete as per specification no. FF-VL/BFV

Supplying & Installing cast iron double flange butterfly valve of size 100 mm dia. as per specification No. FF-VL/BFV

Supplying & Installing cast iron double flange butterfly valve of size 150 mm dia. as per specification No.FF-VL/BFV

Supplying and installing double flange NRV of size 100 mm dia as per specification No. FF-VL/NRV

Supplying and installing double flange NRV of size 150 mm dia as per specification No. FF-VL/NRV

Supplying and installing Stainless Steel single outlet hydrant valve fitted with necessary accessories complete as per specification No. FF-VL/HV

Supplying and erecting 15 mm (½") dia. NBCM Body chrome finished quartzoid bulb pendent sprinkler having 68º C fixed temperature rating with deflector disc of conventional construction as per specification No. FF-SPR

Supplying and erecting 15 mm (½") dia. NBCM Body chrome finished quartzoid bulb Upright sprinkler having 68º C fixed temperature rating with deflector disc of conventional construction as per specification No. FF-SPR Upright

Supplying & erecting gun metal gate valve of size 25 mm dia complete as per specification no. FF-VL/GV

Supplying & erecting gun metal gate valve of size 50 mm dia complete as per specification no. FF-VL/GV

Supplying, erecting, testing and commissioning vane type water flow detector suitable for detecting flow of water in wet sprinkler pipe of main line or branch lines of 75/80 mm dia having following features 1) Visual switch activation 2) Rugged switch assembly 3) Heavy duty aluminium pipe saddles 4) Durable metal enclosure 5) Steel U bolts for secure mounting 6) Two SPDT ( Single pole double track ) synchronised switches 7) serviceable without draining pipes

Supplying and erecting 20/25mm Ø G.M.air release cock, with necessary G.I. coupling to be fitted on top of Air vessel or on wet riser as per specification No.FF-FFA/ARV

Supplying and erecting 1000-1500 mm long, 25 mm dia. Stainless steel corrugated braided flexible pipe (hose) for dropping sprinkler below false ceiling. Pipe shall have 16 bar rating and with union/reducer coller,clamps etc. as required. Pipe shall have UK/EN listing.(NON CSR)

Supply, installation, testing and commissioning of Fire Alarm Valve of dia 150mm with a cast iron material

Supplying and installing wall mounting swinging Hose reel drum fitted with 19 mm dia. 30m long high pressure polypropylene (Polyhose) fitted with necessary accessories complete as per specification no. FF-FFA/HV

Supplying fire fighting R.R.L. Hose pipe, 63mm dia,2 no of 15m in length, fitted with necessary accessories complete as per specification no.FF-FFA/RRL

Supplying Stainless Steel branch Pipe 63 mm Ø fitted with 20 mm dia detachable hexagonal nozzle as per specifications No. FF-FFA/NZ

Supplying and erecting M.S./CRCA cabinet for housing Floor Hydrant valve, hose pipe, hose reel and branch pipe (size 1000 mm x 736mm x 736 mm.) made from 16 SWG sheet and angle iron 25 mm. x 25 mm. x 4 mm. having front doors with viewing glass (8"x6") and locking arrangement with necessary fixing material such as rubber bidding etc. duly painted in post box red colour.

Supplying and installing pressure gauge of 100 mm Ø., 0-300 PSI or 0-14 kg per cm square fitted with 12/15 mm Ø. Pad cock valve, and G.I. pipe, elbow etc. as per requirement in an approved manner as per specification No. FF-FFA/PG

Supplying and installing DANFOSS make pressure switch with 12/15 mm Ø isolation valve, G.I. nipple, elbow etc. in an approved manner as per specification No. FF-FFA/PS

Supplying and installing fire brigade Header of 150 mm Ø, for supplying water in fire tank as per specification No. FFFA/ FBC

Supplying and erecting fire brigade header (Siamese connection) of 150 mm dia for supplying water to wet riser system complete as pe specification no. FF-FFA/SMC

Providing coating of Bitumen Paint & 4mm thick Wrapping as per IS 10221 for underground 150 mm Ring Main of Fire Fighting System.

Supply and Installation of Anti-Vibration Pad for Pump Room as per specification

Supplying and installing Testing and commissioning of Rubber Expansion bellows on discharge side of pump confirming to EGMA with all hardware companion flanges and gaskets Etc. Size 150mm

Supplying and installing Testing and commissioning of Rubber Expansion bellows on discharge side of pump confirming to EGMA with all hardware companion flanges and gaskets Etc. Size 100mm

Supplying and installing water flow meter of 100mm diameter with material of gun metal

Supplying and installing Air Vessel of 300 mm Ø 1.5m in height M.S. tank installed inside pump house as per specification No. FF-FFA/ACT

Supplying, installing, testing and commissioning with perfect aligning, proper levelling of booster pump of 900 LPM at 40 m Head, 12.5 HP (10 KW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per specification no. FF-MFP/BP

Supplying, installing, testing and commissioning with perfect aligning, proper levelling of fire service main multi stage pump, of 2800 LPM at 76 m head centrifugal type, 75 HP (55 kW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per specification no. FF-MFP/MSC

Supply, Installation, Testing and Commissioning of diesel engine driven stand by fire pump suitable for automatic operation and consisting of following: . (a) Horizontal, centrifugal, pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal to ensure a minimum pressure of 3.5 kg/sq.cm. at highest and farthest outlet at specified flow of 2400 lpm at 60 m head conforming to IS 1520. (b)Suitable HP and RPM water cooled diesel engine with radiator conforming to relevant BS & IS standard complete with auto starting mechanism, 12 volts/24 Volts electric starting equipment, Diesel Tank, exhaust pipe extended upto 1 m. outside pump house duly insulated with 50 mm. thick glass wool with 1.0 mm. thick aluminum sheet cladding, residential silencer, instruments and protection as per specification, stop solenoid for auto stop in the event of fault with audio indications, painted with post office red color etc. as required. (c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (d) Suitable cement concrete foundation duly plastered with anti vibration pads. Complete in all respect as per spec.

Supplying, installing, testing and commissioning with perfect aligning, proper levelling of jockey pump of 240 LPM at 105 m head 20 HP (15 kW), 3 phase, 415 volt, 50Hz or of suitable HP with suitable stages as per specification no. FF-MFP/JP

Supply, Installation, Testing and Commissioning of 4 Loop Microprocessor based analogue addressable type fire alarm control panel, min 125 detectors & 125 modules in single loop, minimum 600 character LCD display, four access levels, min. 1000 event historic logging, flash EPROM sufficient numbers of programmable relay controls for controlling lifts ventilation fans, lift/staircase pressurization fans, monitoring of fire sprinkler and fire hydrant; suitable for 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and capable of operating the system for 30 min during an emergency condition The Fire Alarm panel shall have a provision for Software integration with the Building Automation and Monitoring System.

SITC Analogue addressable photo electric type smoke detectors with detector mounting base complete erected with required accessories.

Supplying and erecting of UL listed and FM approved Single action Manual Pull Station. Shock and Vibration Resistant Pull Down Lever Remains Down Until Reset. Shall be Polarity Insensitive( NON CSR)

Supply and erecting Supply of UL listed loop powered Audible based hooter, shall be powered directly from Signal line circuit (SLC) Shall be of geberating 3,0000 HZ Buzzer tone and provide up to 85 dBA at 3.1m. Provides six (6) fild-configurable audible-tone Highly fiexibl programming and configuration options with independetly controlled outputs by device. (1-7-1)

Supplying, installing, testing and commissioning remote response indicators complete as per specification no. FF-FAAS/RRI

SITC of 220/250 Volts, single phase, 50 Hz Siren of 3.25 km range, Horizontal double mounting type of 1/2 HP 6000 RPM on C. C. foundation complete as per specification no. SRN-AS/SM

Supply, installation, testing and commissioning of Switched mode Power supply unit.

Supplying and erecting XLPE armoured cable 2 core 1.5 sq.mm. copper conductor complete erected on wall/ ceiling as per specification No.CB-LT/CU (FRLS : note2)

Supplying & erecting Carbon Dioxide (CO2) fire extinguisher of 4.5 kg. capacity cartridge type conform to IS 2878 /15683 complete erected with necessary clamp made from 50 x 6 mm. M. S flat with nut & bolts grouted in wall complete.

Supplying and erecting ABC powder type fire extinguisher as per IS : 13849 /15683 of 6 kg capacity with necessary clamp for erection on wall.

Providing Round bottom fire bucket of 9 Litres capacity as per IS : 2546 made out of 24 gauge G.I. sheet with extra handle at bottom duly painted white inside and red outside with FIRE Mark, on provided stand/ wall hook complete.

Providing Floor mounting stand for keeping 4 Nos. of FIRE buckets 1500mm in length, 900mm in height frame made out of 30x30x4 mm angle iron with cross supports for legs, welded with 4hooks and duly painted with one coat of red lead and two coats of silver paint complete.

Supplying & installing one piece moulded HDPE / fibre water tank for negative suction only, having capacity 1000 litres fitted with necessary accessories complete as per specification no. FF-FFA/PT

Supply, installation, testing and commissioning of FIRE MCC PANEL Main incomer 320 A, 25KA 4P MCCB-1 nos, Outgoing feeders as follows. Hydrant pump 75 HP-1No. with Star Delta Starter Sprinkler pump 75 HP-1No. with Star Delta Starter Jockey pump 20 HP - 1 No with DOL Starter diesel Engine Pump of 100 hp Booster Pump 12.5 HP - 1W+1S- 2No with DOL Starter (All starters shall be as per IE2) Engine driven engine controller 1 nos, 12/10 a charger 1 nos, 12/10 a power supply 1 nos, 6 a sp mcb 4 nos, 230/24/12 v 3 c/o relay 3 nos, hooter 1 nospush button 1 nos ind. lamp 4 nos, a/m switch 1 nos. Panel shall to be meet all fire control logic requirement with ON, OFF, TRIP Status. R,Y,B, Trip Indication Lamp, Volt Meter, Multifuction Meter With RS-485

SITC of Microprocessor based LCD Repeater Panel with Min 168 LCD characters & capable of features like of acknowledging / silencing of alarms complete PSU (Min 168 LCD characters)

Supply, installation, testing and commissioning of LPG / PNG leakage detector with addressable monitor module, mounting base, LED, GI Junction box, glands, complete as per specification.

Supply,Installation,Testing & Commissioning of Approved Intelligent Addressable Fault Isolator Module.

Supply,Installation,Testing & Commissioning of Intelligent Addressable monitor modules for 3rd Party Integration such as Sprinkler Flow Switch, Fire doors, magnetic contacts, WLD monitoring complete as required as per specifications.

Supply,Installation,Testing & Commissioning of Intelligent Addressable control relay modules for 3rd Party Integration such as AHU & stairs pressurization Fan, Access control integration etc. complete as required as per specifications.

Providing, supplying and fixing self Luminous Exit sign in accordance with BS 5499 as per sample approved by Client ( Fire Exits)

Excavating hard murum / metal road by chiselling for preparing pit for poles stay or earth plates or for laying cables, pipes & clearing the site by removing debris & making the site as required complete.

Supplying and erecting cast iron foot valve ball type/flap type of size 150 mm dia with strainer for negative suction complete as per specification no. FF-VL/FV

Supplying and erecting 100 mm dia. cast iron foot valve at position with necessary materials complete.

Supplying and erecting one no. brass orifice plate having 6 mm. thickness, 140 mm outer dia and required/proper diameter of inner hole at every single outlet hydrant valve as per specification no. FF-FFA/OP

Making cement concrete foundation in 1:2:4 cement concrete with foundation bolts and nuts complete. (cost of wooden box is included) (for pumps).

Providing & erecting Hot dipped galvanized ladder type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 150 mm width & 100 mm height comprising all required standard accessories.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 150 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Providing & erecting Hot dipped galvanized perforated type cable tray manufactured from 16 swg (1.6 mm thick) GI sheet of 200 mm width & 75 mm height complete with necessary coupler plates & hardware in approved manner.

Supplying and erecting iron, sheet metal work consisting of CRCA sheets, various sections of iron, plates, chequered plates, rods, bars, MS pipes, etc. for panel board or any other purpose with bending, cutting, drilling and welding complete erected at the position with necessary materials duly painted with one coat of red oxide and two coats of enamel paint to match the switchgears or as per directions by the authority.

Supplying & erecting automatic control panel for 3 Ph, 415 volt, a.c. Submersible/centrifugal pump set for 7.5 to 10 HP consisting of DOL starter having relay range 28-42 AMP,S.P.P., Combined ammeter/voltmeter, phase indicating lamp enclosed in CRCA powder coated Vibration proof enclosure with IP 54 protection. Control Panel should offer single phasing, phase reversal, phase imbalance etc.

Supplying, installing, testing and commissioning manual call point (Pill box) with break glass push button in metal enclosure complete as per specification no. FF-FAAS/MCP

Supplying and erecting 20/25mm dia gun metal air release cock, with necessary G.I. coupling to be fitted on top of air vessel or on wet riser complete as per specification no. FF-FFA/ARV

Supplying, installing, testing and commissioning of 2 Zones Microprocessor based conventional fire alarm control panel (FACP) with standard accessories complete as per specification no. FF-FAAS/FACP

Supplying and fixing of Fire Duct Door of Size 1500 (L) x 1350 (W) mm Glazed with 5.5mm clear glass Powder coated MS shutter door as appropriate with universal locking arrangement 3 mm thick CRCA sheet with 6mm thick glazed glass doors including necessary locking arrangement suitable to accommodate double headed internal hydrants, 2 nos 63mm dia synthetic hose pipe 15 m long, 1 no branch S.S. pipe with 4 nos MS angle ( 40 x 40 x 8 ) supports grouted in floor and duly coated with post office red external and white internal paint complete in all respects. with MS Grill of following sizes and types :

Carrying out core cutting of size 3" to 5" dia x 15" length in the C.C./rock/stone wall with the help of specialized core cutting machine in proper manner and finishing the site as original.

Estimate No. :121131-4 of 2019-2020 - Providing Passenger Lifts to the state of Art Office Building and VIP Guest House for MEDA, at Aundh, Pune

Supplying erecting testing and commissioning of 16 passengers’ lift having following specifications.• Rated capacity: - 16 Passengers /1088Kg• No. of Floors: - First floor + 6 upper floors (7 Stops/7 Landings)No of Access sides: - Front and Rear side on first floor, Rear side on six upper floors.• Travel Height: - 25.2 mtrs• Location of Lift Machine: - MRL• Rated speed: - 1.5 m/sLift shaft available having clear size of 2200mm (W) x 2375mm (D), 1800mm Pit depth, 4500mm Overhead.Drive System: - AC Variable Voltage Variable frequency (ACVVVF)Type of Controller: - Full Collective Control Door Details: - Center opening two panels with frame having clear opening of 1000 mm wide x 2100 mm height made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves/frames. All Landing doors should have 2 hours fire resistance rating.COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with/without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMRL & FCC/ground floor. Clear Car size of 1400mm (W) x 1850 mm (D) x 2200mm (H) with Clear 10mm laminated glass on one side (full height & width). Side for glass wall shall be designated at site at the time of execution. LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings. Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port, control panel duly wired with proper size & strength copper wire for power & control circuit, with provision for addition of floor/ control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class. ARD complete with necessary SMF VRLA batteries.COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with/without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMRL & FCC/ground floor. Clear Car size of 1400mm (W) x 1850 mm (D) x 2200mm (H) with Clear 10mm laminated glass on one side (full height & width). Side for glass wall shall be designated at site at Job includes entire procedure of obtaining all necessary erection permissions &” License to work the Lift” from Electrical Inspector (Lifts) with submission to the Engineer in Charge. The Job covers Three years onsite warrantee for all the Lift parts with FCAMC as per the maintenance schedule.

SITC of Electric Traction Passenger Lift with • Rated capacity :- 8 Passenger/544Kg • Floors :- G+7floor (8Stops/8 Landings) • Travel :- 29.4 mtrs • Location of Lift Machine:- MRL • Rated speed :- 1.0mps VS • Doors type :- COPO/TOPO Doors with frame having clear opening of 800 mm wide x 2000 mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves/frames • Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. • COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with/without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor • Clear Car size of 1300mm wide x 1100.mm deep x 2000.mm high • LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings • Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port, control panel duly wired with proper size & strength copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class • ARD complete with necessary SMF VRLA batteries • Fireman controller having fireman switch at fire Landing, • CCTV surveillance system comprises of 2nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for 60 days with 18" FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. • Lift Machine of Gearless PMSM of suitable kW with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly speed of 1.5 mps, add as below,For Lift having 900mm wide x 2000mm high clear entrance in 1.5mm thick SS 304 grade landing door [Two panel], this includes all necessary accessories like LOP's with UP/DN buttons-arrowsindicators,extension of guide rails, shaft wiring with trunking, travelling cables, main hoisting ropes/belts, & OSG rope landing doors with all accessories etc. necessary for the normal safe functioning of lift installation complete.Full Collective control system should be added. Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge.The job covers Three years onsite warrantee for all the Lift parts with FCAMC as per maintenance schedule.

SITC of Electric Traction Passenger Lift with • Rated capacity :- 8 Passenger/544Kg • Floors :- B+G+7floor (9Stops/9Landings) • Travel :- 33.6mtrs • Location of Lift Machine:- MRL • Rated speed :- 1.0mps VS • Doors type :- COPO Doors with frame having clear opening of 800 mm wide x 2000 mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves/frames • Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. • COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with/without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor • Clear Car size of 1400mm wide x 1850mm deep x 2200mm high • LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings • Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port, control panel duly wired with proper size & strength copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class • ARD complete with necessary SMF VRLA batteries • Fireman controller having fireman switch at fire Landing, • CCTV surveillance system comprises of 2nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for 60 days with 18" FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. • Lift Machine of Gearless PMSM of suitable kW with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly speed of 1.5 mps, add as below,For Lift having 900mm wide x 2000mm high clear entrance in 1.5mm thick SS 304 grade landing door [Two panel], this includes all necessary accessories like LOP's with UP/DN buttons-arrowsindicators,extension of guide rails, shaft wiring with trunking, travelling cables, main hoisting ropes/belts, & OSG rope landing doors with all accessories etc. necessary for the normal safe functioning of lift installation complete.Full Collective control system should be added. Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge.JOB covers onsite Warrantee for all the Lift Parts with FCAMC as per the maintenance schedule.

SITC of Electric Traction Passenger Lift with • Rated capacity :- 4 Passenger/272Kg • Floors :- G+1 floor (2Stops/2 Landings) • Travel :- 3 to 4.2 mtrs • Location of Lift Machine:- MRL • Rated speed :- 1.0mps VS • Doors type :- COPO Doors with frame having clear opening of 700/800 mm wide x 2000 mm high made from SS 304 grade sheet of 1.5mm, thick in hairline finish for car and all landing doors with SS door architraves/frames • Lift car enclosure made from SS 304 grade sheet of 1.5mm, thick with hairline finish with frame made from MS girders, bracing of adequate size with minimum safety factor of 5, with Toe Guard Apron, with necessary false ceiling with adequate LED lights, blower/fan for ventilation & SS chequered plate flooring, handrails, mirror, emergency light etc. • COP with SS face plate having metallic push buttons with Braille Code & luminous indicator around button with FPI, scrolling UP/DN LED indicator & with / without attendant key switch, OWD with audio-visual alarm, VAS in Marathi, Hindi & English with intercom system with telephone instrument in Lift car, LMR & FCC/ground floor • Clear Car size of 1100.mm wide x 700mm deep x 2000mm high • LOP with SS face plate having recess/surface push button box for all landings with scrolling UP/DN LED indicator having metallic push buttons with Braille Code & luminous indicator around button with CPI, Lift car arrival & next travel direction audio-visual indication at all landings • Lift controller based on microprocessor/ PLC with VVVF Drive having closed loop control system, with IBMS compatible having necessary port, control panel duly wired with proper size & strength, copper wire for power & control circuit, with provision for addition of floor/control card & allied accessories control panel having enclosure of 1.5mm CRCA sheet with powder coating with IP54 Protection class • ARD complete with necessary SMF VRLA batteries • Fireman controller having fireman switch at fire Landing. • CCTV surveillance system comprises of 2nos minimum 2.0MP FHD IP based vandal proof Dome camera in lift car & in LMR/inside lift shaft top aimed on Lift machinery & controller with NVR kept in LMR/FCC with HDR data backup for 60 days with 18” FHD TV monitor, to be kept in FCC/LMR as directed by Engineer In Charge. • Lift Machine of Gearless PMSM of suitable kW with Traction pulley, OSG, electromagnetic brakes, entire assembly mounted on adequate size girders duly Job includes entire procedure of obtaining all necessary erection permissions & "License to Work the Lift" from Electrical Inspector(Lifts) with submission to the Engineer In Charge.The job covers Three years onsite warrantee foe all the lift parts with FCAMC as per the maintenance schedule.

Supplying and erecting PVC trunking (PVC casing-n-capping) of size 20 mm with accessories on wall/ceiling as per specification No: WG-MA/CON.

Supplying and erecting mains with 1x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG- MA/BW

Supplying and erecting mains with 2x1.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places as per specification No: WG- MA/BW

Supplying and erecting green colour earthing with 1x 2.5 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting mains with 4x 4 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting mains with 2x4 sq.mm F.R copper PVC insulated wire laid in provided conduit/trunking/inside pole/Bus bars or any other places. as per specification No: WG-MA/BW

Supplying and erecting ISI mark modular type switch 6A / 10A duly erected on provided plate and box with wiring connections complete.

Supplying and erecting ISI mark modular type 3 pin 6 / 16A multi socket with safety shutter, duly erected on provided plate and box with wiring connections complete.

Supplying and erecting PVC Surface modular switch box with double mounting plate for 4 modules duly erected.

Supplying and erecting bulkhead fitting suitable for upto LED upto 12W fixed on wall. As per specification no. FG-IDF/BHF

Supplying and erecting 5W-7W, 230V integral type LED Lamp suitable for B-22/E-27 base

Supplying, erecting and marking SPMCB 6A to 32A, B- series (for lighting) in provided distribution board as per specification no. SW- SWR/MCB

Supplying, erecting and marking FPMCB 6A to 32A in provided distribution board as per specification no. SW-SWR/MCB

Supplying and erecting single pole and neutral distribution board (SPNDB) with door surface/flush mounted with 2 ways for incoming and 10 ways for outgoing SP MCB’s on iron/ GI frame as per specification no. SW-SWR/MCBDB

Supplying and fixing CRCA sheet Box with earthing terminals for housing 2 Pole RCCB on iron frame/laminated board complete.

Supplying and fixing CRCA sheet Box with earthing terminals for housing 4 Pole RCCB on iron frame/laminated board complete.

Supplying, fixing and commissioning of 2 pole,RCBO (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6/10/16/20/25A, as per specification no SW- RCCB/RCBO

Supplying, fixing and commissioning of 4 pole RCBO ( (residual current breaker with overcurrent short circuit 10 kA and earth leakage protection), with 30/100/300 mA sensitivity and having capacity of 6A/10A/16A/20A/25/A as per specification no SW- RCCB/RCBO

Supplying, erecting & terminating XLPE armoured cable 2 core 2.5 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Supplying, erecting & terminating XLPE armoured cable 4 core 4 sq. mm. copper conductor continuous 5.48 sq. mm. (12 SWG) G.I. earth wire complete erected with glands & lugs, on wall/ trusses/ pole or laid in provided trench/ pipe as per specification no. CB-LT/CU

Providing earthing with copper earth plate size 30 x 30 x 0.315 cm complete with all materials, testing & recording the results as per specification no. EA-EP

Supplying and erecting copper strip of required size used for earthing on wall and/or any other purpose with necessary copper clamps fixed on wall painted with bituminous paint in an approved manner with joints required. As per specification no. EA-EP.

Supplying and erecting Annealed bare copper wire of high purity of different sizes used for earthing on wall with necessary copper clamps fixed on wall/cable/conduit with screws in an approved manner.

Shubham EPC Private Limited

SAURABH CONSTRUCTION