SPL REPAIR TO MANTLET BUTT REVIEWING GALLERY OF SA FIRING RANGE CR III AT PW DIV AT INF SCHOOL AND SPL REPAIR TO ROOF OF BLDG NO T 201 AT GAUR ENCLAVE AND PROVN OF CERTAIN REVENUE AND MINOR WORKS UNDER GE MIS MHOW

Amount

Demolition of cement concrete n.exc 15cm depth in any discription and any position not otherwise specifically provided (below or above ground level) and removal demolition of cement concrete from site up to 500 m complete all as specified and directed.

M & L for cement concrete 1:4:8 type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete, sub base of floor etc complete all as specified and directed.

M&L for 50mm thick PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) as in flooring work finishing exposed surface complete all as specified and directed.

Demolition of roofs, floors (other than ground floors) beams, staircases, landing, chujjas and similer suspended work if cement concrete is reinforced ( reinforecment cut as required to fecilate demolition) surface complete all as specified and directed.

Formwork to faces of walls, retaining walls, abutments, parapets and stairecases railings and similer work including attached pillasters, buttresses etc; vertical or to better, flat rough finished surfaces of concrete surface complete all as specified and directed.

M&L for RCC (design mix) M-25 (20mm graded stone aggregate) as in walls, retaining walls basement walls, ballest walls and the like; any thickness; above top of footing; including attached pilasters and buttresses surface complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof roof slabs, floor slabs, landing and similar work;not exceeding 200mm thick (horizntal or sloping ) flat rough finished surfaces of concrete complete all as specified and directed.

M&L for RCC (design mix) M-25 (20mm graded stone aggregate) slabs supported on walls beams and columns in floors,roofs, landings,balconies canopies duck slabs and in shelves and the like complete all as specified and directed.

Formwork to sides and soffits of floor or roof beams haunching, lintel, coloumn, cantilevers shelves includig supported over hangs etc with rough finished flat surfaces of concrete complete all as specified and directed.

M&L for RCC (design mix) M-25 (20mm graded stone aggregate) as in beams, cantilevers.brussumenrs, lintels over than 1.50 span complete all as specified and directed.

M&L for Mild steel TMT bars 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, footing, roof beam, plinth beam, slab,chajjas and similar work hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for 6mm to 8mm dia and over mild steel TMT bars cut to length bent to shapes as required including bending cranking and binding with mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Demolition of brick work built in cement mortar including all quions ,arcches , pillars etc complete all as specified and as directed.

M&L for brickwork with using fly ash brick, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar 1:4 mixed with integral water proofing compound while concrete surface is green and finish the surface even and smooth without using extra cement complete all as specified and directed. Note:- WPC shall be measured and paid separately.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for rendering 10mm thick in cement mortar 1:6 on brick surface of walls finishing even & smooth without using extra cement complete all as specified and directed.

M&L for providing and applying minimum 1.00mm to 1.50mm thick wall care putty over prepared surface to achive the surface even and smooth for painting. after complete removal of existing treatment of any type of surfaces, make surface clean, free from dust, loose pint etc complete all as specified and directed.

M & L for preparation of surfaces and applying two coats of oil bound distemper with roller on old treated surface of wall etc complete all as specified and directed.

M & L for preparation of old treated surfaces of ceiling and applying one coat of white wash complete all as specified and directed.

M&L for two or more coats of 100% premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489-2004, Alkali and fungal resistance,dirt resistance exterior paint of required shade (Company Depot Tinted) 1.43 litre/10sqm over and including priming coat of exterior primer applied @ 0.90 litre /10sqm over new surface including preparation of new surfaces complete all as specified and directed.

Excavation in trenches n.exc 1.50 m wide and n.exc 1.5m depth: for foundation, etc or for shafts, wells cesspits, manholes, pier holes, etc n.exc 10 sqm on plan & n.exc 1.5m in depth & getting out in hard/dence soil complete all as specified and directed.

M&L for Moorum/red bajri filling in floors or paving laid in layers n. exc. 15 cm thick, spread, levelled and rammed including watering as required complete all as specified and directed. Note: Consolidated thickness shall be measured.

Taking down chowkhats or frames with shutter (with out taking off shutters from the frame) area n. exc 1.5 sqm each complete all as specified and as directed.

S&F factory made steel window , with side hung shutter including projecting hinges with steel handle, peg stay with galzing bars devetailed or welded complete all as specified and directed.

S&F in repairs steel rolling shutters thickness of lath in 1.25mm with ball bearing for rolling shutter,as specified including top cover, anchoring rod, hesp and staple and one shop coat of primer ercted in position as indicated, complete push pull or manual type and including safety lever locks mild steel with 4 levers for rolling complete all as specified and directed.

Taking down shuters of any description n. exc 1 sqm each and removing from site complete all as specified and directed.

S&F 2nd class hard wood as in plain, solid straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and as directed.

S&F 35mm thick factory made 2nd class hard wood plain, framed pannelled shutters (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneered particle board wiyh commercial veneering on both faces. The size of rail and stile as per (IS : 1003 part-I , kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 35 mm thick factory made, 2nd class hard wood glazed and skeleton shutters open rebeated and prepared to received glass, gauzed, with out sash bar edges of framing plain, chamfered or rounded, fitted with cut and mitered beads for securing glass etc, size of member of shutter as per specified in SSR Part-I Section 8, clause 8.24 (a) and for door and fixed with chowkats, chemically pressure treated complete all as specified and as directed.

S & F stainless steel wire cloth of 0.36mm dia wire and average width of aperture 1.4mm & fixed with tacks of stainless steel wire staples,etc complete all as specified and as directed.

S & F sheet glass ordinary quality 3mm thick and glazing with oil putty in squares. not exc 0.5 Sqm each complete all as specified and as directed.

S & F in repair galvanized mild steel wire clothes 0.56 nominal dia of wire and average width of aperture 1.18mm fixed with beading complete all as specified and directed.

Hacking out old broken glass ( any tickness size ,quality or description ) from wooden frame or stone etc and S&F 3.00 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beading in square not exceeding 0.50 sqm in each panes complete all as specified and directed.

S&F 100 mm Butt hinges medium weight cold rolled mild steel and fixed complete all as specified and directed.

S&F 150 mm long Aluminum anodized barrel tower bolts of extructed section complete all as specified and directed.

S&F aluminum alloy handles fabricated anodised of 150 mm long complete all as specified and directed. .

Taking down cement plaster on brick or concrete surfaces, parapets including raking out joint, hacking for key, scrubbing down with water etc complete all as specified and as directed.

M&L for 2mm thick wall care putty in two coats (each coat not less than 1mm) over a coat of on walls where required and surface finished even and smooth with sand paper complete all as specified and directed

M&L for preperation of new plastered syrfaces of wall anf applying two coats of 1st Quality oil emulsion distember over over a coat of primer complete all as specified and directed.

M&L for preparation of new /old plastered surfaces of walls and applying two coats of Acrylic Smooth exterior paint of required shade (@ 1.67 ltr/10 sqm) over over a coat of primer(@ 2.20 kg/10 sqm) same make base complete all as specified and directed.

M&L for preparation of old decorated plastered surfaces or un-plastered surfaces of wall and applying two coats of oil emulsion distemper complete all as specified and directed .

M&L for preparation of old painted surfaces of wood/wood based materials exc 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed .

Demolition of cement concrete in ground floor and paving not exceeding 15cm thick ( below or above ground level ) complete including removal of debries out side MD land all as specified and as directed .

M&L for 75mm thick cement concrete 1:3:6 type C1, with using 20mm graded stone aggregate as in floor/ plinth protection Finishing surfaces of concrete topping even and fair (without using extra cement) including making joint at every 3m interval and at corner and filled with mixture of bitumen and sand and finished even and fair and laid in alternate bays complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors complete all as specified and as directed.

M&L for machine cut Kota stone slab for flooring 20-25mm thick over and including cement screed bed of 20mm thick in CM 1:6, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M&L for machine cut Kota stone slab 20-25mm thick over and including 15mm thick rendering in CM 1:4, in riser of steps, skirting, dado and pillar, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

Dismantling of asbestos cement (corrugated, semi-corrugated, etc.) sheets in roof coverings etc complete all as specified and as directed.

S&F 0.50mm thick (including coated thickness) pre-colour pre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and as directed. Note :- Rate for making shape in any curvature, radius or angle (as directed by Enge-in-Charge) are included in quoted rate.

S&F 0.50mm thick plain (including coated thickness) pre-colour pre- profiled (Galvalume/zinkalume) sheets of required colour and design having tensile strength of 550 Mpa as in roof sheeting/sunshade/ wall cladding, north light curves, fixed with zinc coated self drilling fastener including EPDM washer complete laid with one corrugation side laps and min 150mm end lap laid to slope all as per manufacturer / profile maker instruction complete all as specified and as directed.

Dismantling old wooden trusses, timber scantlings , fillets, rails, posts, rafters, purlins, etc. in any size, description and in any position under 40 sq. cm insection in framed work complete all as specified and as directed.

S&F Mild steel Hollow Section work in tubular trusses, purlins, rafter, tubler column, where connected common rafter and running rails fixed with angle cleat or other connection plates including special shaped washer etc, complete using ERW or induction butt welded tubes conforming IS-4963,1993 and IS-1161-1979 grade ST-240 complete all as specified and as directed.

S&F Mild steel plates (Plain or chequered) as in shoe plate, base plate and gusset plates forming holes for roof frame work, trusses, rafters etc of grade Fe 410-W (Gde E- 250) quality A complete all as specified and as directed

S&F Mild steel framed work such as grills,gratings, etc.. with ends of barsshouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors;ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed.

M&L for RCC type B0 1:2:4 (using 12.5mm graded stone aggregate) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses,lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones,bed plates, kerbs 8, water troughs and the like including weathering, slightly rounded or chamfered angles and throating complete all as specified and as directed.

M&L for preparation of newly steel surfaces, of any description, over 10 cm width or girth, and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, hard/dense soil., etc complete all as specified and directed.

M&L for PCC 1:3:6 type C2 (using 40mm graded stone aggregate) as in foundation filling and mass concrete etc complete all as specified and as directed.

M&L for chequered cement concrete tiles (glossy finished) with grey cement and pigment of size 25cmX25cmX25mm thick ,set and jointed and pointed in neat cement slurry in floor etc over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for machine pressed designer precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade laid over and including 25mm thick (compacted thickness) sand cushion complete all as specified and directed.

Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm in soft/loose soil complete all as specified and directed.

Excavation in trenches n exc. 1.5 m wide and n exc. 1.5 m in depth for foundation etc or for shafts, wells, cesspits, manholes, pier holes etc n exc. 10 sqm on plan and getting out in soft/loose soil comlpete all as specified and directed.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm and getting out in soft/loose soil complete all as specified and directed.

Removing of surplus material exc 250m but n exc 500m and deposited where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

Returning, filing in, including spreading, leveling watering and well ramming in layers not exceeding 25 cm in soft/loose soil or any type soil etc complete all as specified and directed.

M&L for hardcore of broken stone or boulder of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface

M&L for 50mm thick Cement Concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) as in sub floors, sub bases, floors and paving etc all as specified and directed by Engr in charge.

M&L for PCC 1:3:6 type C-2 (using 40mm graded stone aggregate) as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns, pillars, boundary pillars and posts (including caps and bases), etc complete all as specified and directed

S&F Rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates conforming to Fe 410-W (Gde-E-250) quality-A complete all as specified and directed Note :- Rate for making shape in any curvature, radius or angle (as directed by Enge-in-Charge) are included in quoted rate.

Surface dressing n. exc 15 cm deep in soft/loose soil complete all as specified and direceted.

Excavating over areas, n exc 1.5 m deep and getting out in soft/loose soil complete all as specified and directed.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed.

M&L for RCC (design mix) M-25 (20mm graded stone aggregate) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete and the like complete all as specified and directed.

M&L for RCC (design mix) M-25 (20mm graded stone aggregate) as in roof beam, plinth beam,roof beam, lintel beams and Columns complete all as specified and directed.

M&L for RCC (design mix) M-25 (20mm graded stone aggregate) as in chajjas complete all as specified and directed.

M&L for RCC (design mix) M-25 (20mm graded stone aggregate) as in Columns, footing, pillars, piers, posts and struts complete all as specified and directed.

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc fair finished surfaces complete all as specified and directed.

Formwork to sides of pillars, posts, struts, piers, columns and stanchions etcfair finished surfaces complete all as specified and directed.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) fair finished surfacescomplete all as specified and directed.

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.fair finished surfaces complete all as specified and directed.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed.

M&L for brickwork with using fly ash brick, straight or curved on plan exc 6m mean radius built in CM 1:4 complete all as specified and directed.

M&L for 15 mm thick rendering in CM 1:6 on brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for 5 mm thick rendering in CM 1:3 on brick work or concrete surfaces, surfaces finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coat of Ist quality exterior weatherproof water base emulsion paint over a coat of primer of same make on wall as specified and directed pillasters, cornices etc scrapping down , brooming down or steel wire brushing, and washing with water after completion of precoat treatment applying two coats of Anti fungal Weather coat paint (Exterior emulsion) white or tinted over a coat of primer (X2) complete all as specified and directed. Note :- (a) Each stage i.e preparation of surfaces, application of primer, application of first coat. application of second coat will be got passed from Engr-in-Charge/GE. (b) Written Warranty for four years or as per manufacturer's instructions, whichever is more is required to be furnished by contractor for this item.

M&L for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over a coat of alkali resistance primer complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash on ceiling surface complete all as specified and directed.

S&F aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips,rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) incl powder coating of any colour (Thickness or powder coating not less than 50 micron) complete all as specified and directed.

S&F galvanised mild steel wire cloth of 0.56mm dia wire and average width of aperture 1.18mm & fixed with tacks or galvanised I wire staples,etc complete all as specified and as directed.

S&F figured glasspine head type 3.0 mm thick ordinary quality and glazing with oil putty, in squares n. exc 0.5 Sqm in each pan complete all as specified and directed.

M&L for coloured Non Skid ceramic tiles 7 to 8mm thick (squares/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 20mm thick screed in CM (1:6) complete all as specified and as directed.

M&L for glazed ceramic coloured tiles 450mm x 300 mm size 6 to 7mm thick in dados or skirting over & including rendering 10mm thick in CM (1:4), jointed in neat grey cement slurry and pointed in white or colour cement to match the tiles as directed and specified.

S&F wash hand basins, vitreous china,of size 550x400mm (flat back, or angle back type) including cutting for and pinning in ends of brackets or erecting stand with CP waste coupling exclusive of fixing of supply and waste pipe etc complete all as specified and directed.

S & F vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) complete complete all as specified and directed.

S&F PVC valveless, syphonic action type flushing cistern,low/high level white with inlet ball valve float and handle including brackets complete fixrd in repair capacity of flush 10 ltrs complete all as specified and directed.

S&F vitreous china urinal half stall type 350x390x600 mm (minimum) height with including providing & fixing of plugs bedding against wall in cement mortar 1:2 pointing around urinal back in cement mortar complete all as specified and directed.

S & F CP brass Urinal spreader for fixing with 15 mm dia pipe complete all as specified and directed.

S&F Urinal partition of size 900x450x350 mm having thickness 10-12mm of HPL board material fixed with brackets complete all as specified and directed.

S & F PVC waste pipes of 40/32mm bore suitable for wash hand basins/sinks/urinals outlet of 0.90m to 1m lemgth complete all as specified & directed.

S & F 32 mm bore low density polythene pipe (LDPE) of pressure rating 6 kgf / Sqcm for WHB and sink complete all as specified and directed.

S&F 75 mm bore PVC floor traps plain with grating and 300 mm long out let including jointing and etc all as specified and directed.

S & F PVC pipe of 40 mm dia, in any length and in any position such as walls, ceiling or laid in floor or trenches etc. complete all as specified and directed.

S & F PVC bend for 40mm dia PVC pipe complete all as specified and directed.

S & F PVC bends 75mm bore, any radius complete all as specified & directed.

S&F PVC (SWR) pipes of dia 110 mm single socketed in any length with rubber ring joints laid in trenches or in floors of dia 110 mm complete all as specified and directed.

S&F PVC (SWR) pipes of dia 75 mm single socketed in any length with rubber ring joints fixed to walls of dia 75 mm complete all as specified and directed.

S&F Bib taps (push type) cast copper alloy chromium plated with crutch or butterfly handle, screwed down, screwed for iron pipe of 15mm bore, complete all as specified & directed.

S&F fancy type chromium plated two way bib cock of 15mm bore ,screwed for iron pipe or brass ferrule etc complete all as specified and as directed.

S&F pillar taps (swan neck), fancy type cast copper alloy with capstan heads, chromium plated, screwed down, high pressure with or without lettered “hot” or “cold” with long screwed shanks and fly nut screwed for iron pipe of 15mm bore, complete all as specified & directed.

S & F stop/angle cock cast copper alloy high pressure, angle valve type, chromium plated suitable for 15mm bore steel pipe complete all as specified and directed.

S&F health faucet with S.S. flexible pipe of 1.00 to 1.50 metre length including holder complete all as specified and as directed.

S & F PVC connections of 450mm long of PRYAG Make suitable for 15mm dia iron pipe including PTMT nuts complete all as specified & directed.

S & F 15mm bore, tubes medium grade, galvanized with all fittings and fixed to walls and ceiling or laid in floors including testing complete all as specified & directed.

All as per serial item No. 114.00 above, but 20mm bore.

Cutting chases, pinning in, making good to facings where required and pointing in CM(1:3) to ends or edges of landings, steps, cills,sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth in Stone/ brick walls complete all as specified & directed.

S&F Gun -metal,globe or gate valves,with iron wheel head ,screwed both ends for iron pipe and fixed complete all as specified & directed.

S & F 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S & F rotational moulded polythylene 500 Ltr capacity water storage tank (double layer)(cylindrical/vertical with closte top) hoisted and fixed in position all as specified in SSR Part-I including providing and fixing PTMT ball valve high pressure with polythene float and fly nut, 20mm bore complete all as specified & directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm vide with chromium plated bracket guard and railing 60cm long complete all as specified & directed.

S&F for PVC door frames of sizes 50 x 47 mm made out of 5 mm prelam PVC sheet reinforced with MS Square tube in opening of suitable size complete all as specified and directed.

S&F Factory made (Prelam on both sides) solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall covered with heat moulded prelam PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for styles and prelam PVC sheets for top rail, lock rail and bottom rail in either side and as gap insert for top rail and bottom rail pannelling of prelam PVC sheet to be filled in the MS welded/sealed to the styles and rails with suitable PVC sheet beading and jointed together wiht solvent and fixing in the frame at site as per specification and drawing complete all as specified and directed.

S & F stainless steel butt hinges 100 mm long complete all as specified & directed.

S&F 150 mm long Aluminium anodizes barrel tower bolts of extruded section complete all as specified & directed.

S&F 150 mm size aluminium anodized handle complete all as specified & directed.

M & L for applying a tack coat of Industrial bitumen grade of 85/25 at the rate of 1.2 Kg per Sqm including cleaning surfaces (one coat for bonding material below membrane) complete all as specified & directed.

M & L for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified and directed.

M&L for applying two coats of bitumen based aluminium painting @ 0.15 Kg / sqm each coat on water proofing treatment with preparation of surface as on non assesible area complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm dia complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm dia complete all as specified and directed.

S&F PVC junction single (single T) 110mm dia equal or unequal with access door.

S&F PVC junction single (single T) 75mm dia equal or unequal with access door complete all as specified and directed.

S&F 100mm stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

S&F 75mm stack clamps out of 50 mm by 5 mm flat iron and 16mm dia round iron stays, including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed.

M&L PVC (SWR) floor trap 75mm dia plain with grating including jointing with solvent cement complete all as specified and directed.

M&L PVC (SWR) gully trap 125/110 mm, setting & jointing with solvent cement

M & L for PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in bed drain pipes of 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested including taking down existing concrete complete all as specified and directed.

M&L for Salt glazed stoneware drain pipe Grade 'A' 150 mm bore laid in trenches and jointed including taking down existing pipe complete all as specified and directed.

M & L for precast cement concrete 1:2:4, type B1 (Using 20 mm graded stone aggregate) in landings, bed plates, pintle blocks, anchorage blocks, cover slabs (for manholes and drains etc.) shelves and similar articles with plain faces and set in cement mortar 1:4 including necessary form work , complete all as specified & directed.

M & L for PCC 1: 2 :4 type B-2 (using 20mm graded crushed stone aggregate) as in surface channels and drains including necessary form work complete all as specified and directed.

M&L for PCC 1:3:6 type C-1 using 20 mm graded stone aggregate as in coping to drainage complete all as specified & directed.

M&L stone dust under floors or in foundations including watering and consolidation spreading and levelling in layers n exc. 25 mm thick complete all as specified & directed.

M & L 60mm thick machine pressed precast concrete interlocking paver block fixing with grey cement and pigments of shape as approved by GE ,and any colour and size confirming to IS 15658-2006 of M-35 Grade set , laid over stone dust and sand cushioning, filling of joints with sand & compaction using surface vibrator after filling of joints lain in any pattern as decided by Engineer-In-Charge including packing of sides by cement concrete finishing surface even and smooth complete all as specified and as directed. Note : Sand cushioning shall be measured and paid separately .

M&L for Point wiring with FR LS PVC insulated PVC unsheathed electric cable 1100V grade single core having multi stranded copper conductor of size 1.5 Sqmm nominal cross sectional area drawn in & including non metallic rigid PVC conduit ISI marked medium grade not less than 20mm dia with all conduit accessories in concealed wiring system by cutting of wall and making good and matching disturbed surface of wall with existing surface of wall (cutting except on ceiling for fan point only, on ceiling instead of PVC conduit surface casing caping will be used) & 1.5 sqmm green FR LS PVC insulated unsheathed copper conductor as earth wire connected to earth dolly by providing lugs including galvanised boxes and bakelite sheet for mounting switches, sockets, fan regulators etc complete all as specified and directed for the following:-

(a) One ligh point controlled by one switch

(b) One Exhaust Fan point controlled by one switch

(c) One 5amps socket out let point controlled by one switch on same board with other switches.

S&F switch piano flush button single pole one way 6 Amp 240 volt complete all as specified and directed.

S&F socket outlet flush type 5 pin, 6 amps, 230 volts complete all as specified and directed.

S&F ceiling rose surface bakelite three terminal complete all as specified and directed.

S&F integrated LED tube light fitting 1x18/20 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square boxes complete all as specified and directed. Make:- Havells Cat No. LHEXBLP7PN1W018 /Bajaj cat Pt No. BCLSB 18WH or equivalent in Wipro as approved by GE.

S&F integrated LED tube light fitting 1x9/10 Watt, 6000K complete fitting with all accessories duly connection with three core flexible copper cable duly fixed on two nos of PVC square box complete all as specified and directed . Make:- Havells Cat No. LHEXBLP7IN1W009 / Bajaj Cat Pt No. BCLSB 10 WH or equivalent in Wipro/Crompton as approved by GE

S&F LED street light fittings 1x35 Watt, 5700K complete fitting having pressure dia cast aluminium housing with heat resistant toughened glass & IP 65 /66protection fixed on and including sufficient length and appropriate size GI bracket with all accessories duly connection with three core flexible copper cable complete all as specified and directed. Make:- Havells Cat No.LHEXAYP7PN6K030 / Crompton Cat No. LSTO-25-CDL /Bajaj Cat No. BCLST 25W LED IV2

S&F double door SPN DBs 4 way of powder coated DB's suitable for MCB's fitted with bus bar,Neutral link,Earth bar and Din ral complete all as specified and directed by Engr-in-Charge.

S&F MCB SPN 6 to 32 amps 10 KA, B-series including connection with suitable size aluminium/copper lugs complete all as specified and directed by Engr-in-Charge.

S&F MCB SP 240 volts 6 to 32 Amps, 10 KA breaking capacity, 'B' series including connection with suitable size aluminium / copper lugs complete all as specified and directed by Engr-in-Charge.

S&F exhaust fan 250mm sweep, AC single phase 230 Volts, non metallic type, complete with louver including electric connection with suitable size copper conductor cable, clamps, nuts, bolts etc including making hole of appropriate size in the existing brick wall and making good the disturbed wall and matching with the existing surface of wall complete all as specified and directed by Engr-in-Charge. Make : Havells Model: Ventil Air-DX white or equivalent in /Bajaj/Crompton as approved by GE.

M&L for earthing complete with galvanized steel earth plate electrode 60cm x 60cmx 6.3 mm thick buried directly in ground ( earth pit not less than 2.25 meter deep below ground level) with the top edge of the earth plate not less than 1.5 meter below normal ground level connected to galvanized earth lead wire 4mm dia by means of bolts, nuts, check nuts and washer of galvanized iron or of steel all as shown in electrical plate No.5 of MES SSR parts-I and including excavation & earth work in any type of soil , disposal of soil , providing alternate layers of charcoal and common salt, construction of PCC earth chamber in mix 1:3:6 type C-1 with 40 mm thick RCC 1:2:4 type B-J cover reinforced with 8mm dia MS TMT bars both ways with lift hook made out of 8 mm dia bar, watering arrangement with funnel and wiremesh and watering pipe of 20mm dia GI light grade and 15mm dia light grade pipe for earth lead protection and testing on completion, complete all as specified and directed.

M/S Sunshine Construction (BID ID -3156827)

Ankit construction (BID ID -3161416)

ms shrilaxminarayan and sons (BID ID -3161453)