SPECIAL REPAIR TO BLDG NO P-100 OFFRS SERVENT ACCN OF COMD HOSP EC UNDER GE ALIPORE KOLKATA

Amount

Cutting openings, through brick walls built in cement mortar or cement lime mortar for door, window and other openings or enlarging existing openings. converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing and removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc.. to store and rubbish not exc. 50m complete all as specified and directed by Engineer-in-Charge.

M&L for brick work with old size burnt fly ash bricks, straight or curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and directed.

M&L for brick work with old size burnt fly ash bricks,straight or curved on plan to any radius in half brick thick walls built in CM(1:4) complete all as specified and directed.

Demolition of reinforced Concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as directed.

M&L for use and waste of formwork to sides of column, pillars, posts, stanchions for rough finished surface complete all as specified and directed.

M&L for use and waste of formwork to sides and soffit of beams, lintels, cantilevers, shelves etc for rough finished surface complete all as specified and directed

M&L for RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for RCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for RCC 1:2:4 type B0 (using 12.5mm graded stone aggregate) as in slabs suported on walls complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending spirally for hopping for columns, beams, slabs etc hooking ends and binding with and including mild steel wire (anealed) not less than 0.9mm dia or securing with clips complete all as specified and directed

All as per item No 10 here-in-before but 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders complete all as specified and directed.

Taking down cement plaster on brick or stone wall surfaces including glazed tiles wherever exists including raking out joints, hacking for key and scrubbing down with water complete all as specified and as directed.

M&L for rendering 20 mm thick cement plaster in two layer ( 10+10 mm thick) on fair face of brick work or concrete surface in CM (1:4) top 10mm thick rendering shall be carried out by mixing water proofing compound @ 250 ml/50 Kg of cement or as per manufaturer instruction, finished fair and even. complete all as specified and directed. [Note -W.P.C. shall be measured and paid separetly as supply only.]

M&L for 15 mm thick rendering in CM (1:6) on other than fair face of brick or concrete surfaces, finishing even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 5 mm thick in CM 1:3 on brick or concrete ceiling surfaces, finishing even and smooth without using extra cement, all as specified and directed.

Supply only integral water proofing compound all as approved.

Taking down of Chowkhat with shutter (without taking off shutter) door / window area n.exc 1.5 Sqm complete all as specified and directed.

Taking down of Chowkhat with shutter (without taking off shutter) area exc 1.5 Sqm but not exc 4.0 sqm complete all as specified and directed.

M&L for 2nd class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

M&L for 30mm thick Flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides fitted to chowkhats complete all as specified and directed

Preparing surfaces of wood and wood based materials, steel and iron work, new or old, of any description and girth, not otherwise described, and treated with tar or coal tar black paint area tarred exc 0.1 sq. m but n exc 0.5 sq. m each complete all as specified and directed.

M&L for PCC 1:2:4 type B0 ( by using12.5 mm graded stone aggregate) as in hold fast block kerbs or mud stops, rounded or chamfered etc complete all as specified and directed.

S&F of Factory made single extruded WPC(Wood Polymer Composite) solid door Frames of size 45 x 70mm comprising of virgin PVC polymer of K value 58-60(Suspension grade), calcium carbonate & natural fibres and non-toxic additives fabricated with mitre joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum frame density of 750 Kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), mimimum compressive strength of 58 N/Sqmm and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof & fire retardant & fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as directed. Note:- Minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable for WPC solid door / window frames, variation in profile dimensions shall be acceptable but no extra payment on this account shall be made.

S&F of Factory made single extruded WPC(Wood Polymer Composite) solid flush door shutter of 30mm size comprising of virgin PVC polymer of K value 58-60(Suspension grade), calcium carbonate & natural fibres and non-toxic additives fabricated with mitre joints after applying PVC solvent cement and screwd with full body threaded star headed SS screws having minimum density of 650 Kg/cum, screw withdrawal strength of 1800 N(Face) & 900 N (Edge), mimimum compressive strength of 50 N/Sqmm, modulas of elasticity 850 N/sqmm & resistance to spread of flame of class A category with property of termite/borer proof , water/moisture proof & fire retardant & fixing with SS butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge. Note:- Cost od necessary SS Butt hinges and ss screws shall be deemed to be included in unit quoted rate.

M & L for Cub-boards shutters made with Particle board 18/19 mm thick, medium density, flat pressed, single layer type or three layer type with BWR type adhesive, fixed with screws to timber frame work complete in all respect as specified and directed.

S&F of Aluminium anodised (powder coated) Three track sliding window frame with shutters with (2 nos glazed and one wire gauzed shutter) including all necessary joining cleats, hold fast, rubber gasket, snap beading and locking arrangements fixed with screws to wall etc. complete with glazing and including 5 mm thick tinted glass to aluminium frame work using rubber gasket and including stainless steel wire cloth of 0.36 mm dia & average width of aperture 1.40mm with staple or suitable fillets wire mesh fitted with screws and washers etc including deco-griil with the following section of frame and shutter:- (A) Sections for shutter :- (i) "H' section 39 x 20 x 1.50 mm thick. (ii) 'Interlock' section 39 x 20x 1.50 mm thick. (iii) 'Edge & Bottom' section 41 x 20 x 1.50 mm thick. (B) Section for frame :- (i) Top & Sides 123 X 29.70X 1.50mm not less than 1.30 Kg /RM. (ii) Bottom 123 X 29.70 X 1.50mm not less than 1.502 Kg /RM and complete all as specified and directed.

S&F of Anodised powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators etc with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

S&F of UPVC ventilator fixed type half portion 4mm frosted glass and half portion stainless steel wire cloth, 0.63mm dia of wire and average width of aperture 1.18mm including taking down old ventilator complete all as specified and directed

S&F of 4.8 mm thick Sheet glass, ordinary quality and glazing in square (n exc 0.5 sq. m in each pane) fixed to aluminium frame work complete all as specified & directed.

S&F of 4.8 mm thick Sheet glass, ordinary quality and glazing in square (exc 0.5 sq. m in each pane) fixed to aluminium frame work complete all as specified & directed.

M&L for Decorative laminate 0.9 mm thick type 1 of surface finish, colour and pattern as approved, fixed on flat or curved surfaced in any size or width with approved adhesive as per manufacturer's instructions complete in all respect as specified.

S&F of Kitchen Sinks with drainage board made of stain less steel 1mm thick, with plugs, washer and wastes; Including bedding in cement mortor to dwarf wall or including fixing cantilever brackets and connecting union to waste pipe, overall size 915mmx460mm, bowl size 410mmx330mmx160mm, complete all as specified and as directed as in repair .

S&F of extruded aluminium alloy handles 150 mm long, fabricated type,anodised complete all as specified & as directed.

S&F of stainless steel sliding door bolts 300mm long with hasp stapple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bots and sliding bolts complete all as specified & as directed.

S&F of Stainless Steel tower bolts with squre type of extruded section with 200 mm long bolt, complete all as specified and as directed.

S&F of Aluminium anodised barrel tower bolts of extruded section with 200 mm long bolt, complete all as specified and as directed.

S&F of Hinges 100 mm, cast brass, with Stainless steel hinge pin, bright polished and fixed, complete all as specified and directed.

S&F of 100 mm long Aluminium anodised, barrel tower bolts of extruded section all as specified and directed.

S&F of 2nd class hardwood Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each complete all as specified and directed.

S&F of stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless wire staples complete all as specified & as directed.

S&F of floor door stopper overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

Dismantling of stone slabs and tiles of any description or thickness in floors,aprons etc laid, bedded & pointed in any mortar complete in all respect as specified and directed.

M&L for 20mm thick Granite ( of any type) work, table rubbed and polished in steps, jambs, pillars, window cills, cooking platforms and like laid over and including 20mm thick screed bed in CM (1:6) and jointed with grey cement slurry and pointed with white cement mortar (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed. Note:- Size of Granite shall be decided by GE

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete in all respect including necessary cutting and polishing by machine as specified and directed by Engr-in-Charge.

Demolition of cement concrete of any description and in any position not other wise specifiy provided for complete in all respect as specified and directed.

M&L for 25mm thick PCC 1:2:4 type 'B-0' (using 12.5 mm graded stone aggregate) as in sub base complete all as specified and directed.

Dismantiling of floor hearth or wall tiles incl cement mortar bedding (but not backing), and removing rubbish off the premises (outside MOD land), complete all as specified and directed.

M&L for joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in toilet / bath floor set and jointed in neat cement slurry and pointed in coloured cement to match complete including 15mm thick screed bed or bedding layer in CM 1:6 all as specified and directed

M&L for 6-7mm thick glazed ceramic coloured tiles of size 250x350 mm in vertical surfaces / skirting /dado set and jointed in neat cement slurry and pointed in cloured cement to match over complete including 10mm thick backing layer in CM 1:4 all as specified and directed

M&L for 100mm thick PCC 1:4:8 type D2 (using 40 mm graded stone aggregate) as in sub base complete all as specified and as directed by the Engr-in-Charge.

M&L for chequered terracotta tiles of 400X 400 X 10 mm thick, set and jointed in neat cement slurry and pointed in white or colored cement to match including 15mm thick screed bed or bedding layers in CM 1:6 for laying complete all as specified and as directed. Make: Johnson endura or equivqlent product of Nitco / Bansal / Anjali / Ultra Tiles Pvt Ltd / Multiwyn

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing etc., and making good, cutting not exc 10 cm girth in brick walls / stone concrete block / or slab walls complete all as specified and as directed.

Taking up or down 15mm bore steel water tubing and connections,including cleaning for refixing or removal from site complete all as specified and as directed.

All as per item No 53 here-in-before but for 20mm bore steel water tubing

All as per item No 53 here-in-before but for 25mm bore steel water tubing

All as per item No 53 here-in-before but for 40mm or 50mm bore steel water tubing

Taking down UPVC pipe 50 mm bore with fittings complete all as specified and directed.

Supplying and laying of CPVC pipes 15 mm outer diameter of SDR 11 & plain CPVC SDR 11 fittings as in walls, ceiling or laying in floors etc. complete all as specified and directed.

All as per item No 58 here-in-before but for 20 mm outer diameter CPVC pipe

All as per item No 58 here-in-before but for 25 mm outer diameter CPVC pipe

All as per item No 58 here-in-before but for 40 mm outer diameter CPVC pipe

All as per item No 58 here-in-before but for 50 mm outer diameter CPVC pipe

S&F of UPVC pipes 50 mm bore (Outer dia) of SCH-40 and plain UPVC SDR 11 fitting fixed on wall or floor, ceiling or laying in floors complete all as specified and directed.

S&F 20 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA) complete all as specified and directed.

All as per item No 64 here-in-before but for 25 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA)

All as per item No 64 here-in-before but for 40 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA)

All as per item No 64 here-in-before but for 50 mm bore CPVC Male Brass Threaded Adaptor (MTA/ MBTA)

S&F of 20mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA) complete all as specified and directed.

All as per item No 68 here-in-before but for 25 mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA)

All as per item No 68 here-in-before but for 40 mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA)

All as per item No 68 here-in-before but for 50 mm bore CPVC Female Brass Threaded Adaptor (FTA/ FBTA)

Dismantling of 100mm cast iron or reinforced concrete drain pipes, jointed in cement mortar and taking out of trenches, if required complete all as specified & as directed.

S&F of 110mm bore PVC(SWR) pipe single socket in any length with rubber ring joints fixed to walls complete in all respect as specified and directed.

S&F of 110mm dia PVC (SWR) pipes double socketed in any length with rubber ring joints fixed to walls

S&F of 110mm bore PVC(SWR) pipe bend any radius complete all as specified & as directed.

S&F of 110mm PVC (SWR) WC connector bent type complete all as specified & as directed.

S& F of PVC (SWR) vent cowl 110 mm dia complete in all respect as specified and directed.

S&F PVC (SWR) 110 mm bore junction single, (Single T) equal or unequal

S&F PVC (SWR) 110 mm bore junction double, (Double T) equal or unequal

S&F of vitreous China wash down water closet pan ( padestal pattern) including PVC water closet seat, black closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device, (excluding fixing bolts, flushing cistern and flush pipe) , including connection to drain ( or outgoing pipe) and to flushing pipe etc comlete all as specified and directed as in repair.

S&F of PVC valveless, symphonic action type low level flushing cistern white with inlet ball valve, float and handle including brackets, 10 ltr capacity complete with flush pipe(Long bend) 32mm dia of make as approved complete all as specified & directed as in repair.

S&F of Toilet paper holder of Chromium Plated fixed to walls with chromium plated (CP) brass screws complete all as specified and directed.

S&F of vitreous china wash hand basin, white, flat back, size 550mm x 400mm, exc chain and plug and porcelain stopper but including cutting for and pinning in ends of and including brackets, waste pipe & CP brass waste coupling of 32mm dia complete all as specified and directed as in repair.

S&F of Brass chromium plated Bottle traps for wash basins with inlet and outlet screwed for pipe or connections including necessary packing, union and cap fixed complete all as specified and directed as in repair.

S&F of 15mm bore CP angular valve fancy type,with crutch handle, screwed for iron pipe or for brass ferrule and fixed of following size comlete all as specified and directed as in repair.

S & F of 15 mm Dia CP Bib taps,fancy type with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed as in repair.

S & F of 15 mm Dia CP stop cock(concealed type) , with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed as in repair.

S&F of 15 mm bore pillar taps, Chromium Plated, with capstan heads, chromium plated, Fancy type screwed down for pipe, high pressure , with or without l'ettered ' 'HOT' or 'COLD' with long screwed shanks and fly-nuts , screwed for iron pipe complete all as specified and directed as in repair.

S&F of 25 mm Dia Gun-metal gate valve , with crutch handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed as in repair.

S&F of PVC connection 15 mm size pipe with PTMT nut of Length 600mm complete all as specified and directed.

M&L for 110/125 mm floor trap fixed in floor with grating incl jointing with solvent cement complete all as specified and directed as in repair.

S&F of brass CP Shower roses with or without swivel joints, 125mm size, including fixing to steel pipes or union comlete all as specified and directed as in repair.

S&F mild steel chromium plated Soap dish, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S&F of brass CP Tubular towel rail, 20mm dia, D type, 60cm long between flanges as in repair.

S&F Curtain rails with Decorative type drappery Rod of anodised aluminium alloy along with all fittings of 25 mm dia complete all as specfied and directed as in repairs.

M&L for rotational moulded polythene water storage tank 1000 litre capacity ISI marked (cylindrical / vertical, double layered with closed top) hoisted and fixed in position including PTMT float valve 20mm, weight not less than 210gms complete all as specfied and directed including dismantling old unserviceable water tank.

M&L for 2000 Litre capacity rotational moulded polyethylene water storage tanks (multilayer.cylindrical / vertical with closed top) with and including 25 mm dia PTMT float valve weight not less than 455 gm, hoisted and fixed in position complete in all respect as specified and directed including dismantling old unserviceable water tank.

Taking out/Stripping of old Roof treatment membranes/Tar felt incl layer of cement mortar of any type carefully from roof surfaces (without damaging roof ) and incl preparation of old roof surfaces by picking, sweeping, cleaning and washing down with water to remove dust & receive new treatment complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4 type 'B-0' (using 12.5 mm graded stone aggregate) finishing even and smooth without using extra cement for padding concrete with a slope of 1:40 complete all as specified and directed.

M&L for 10 mm thick rendering in cement mortar 1:4 mixed with Water Proofing Compound as per manufacture's instructions and top surface of rendering finished even and smooth to recieve water proofing treatment complete all as specified and directed. Note : Water Proofing Compound shall be measured and paid separately.

M&L for applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 kg per sqm including cleaning surface on roof surface for fixing APP membrane complete all as specified and directed.

M&L APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid over bitumen coated surface of roof applied with proper torch flames all as per manufactures instruction. NOTE:- The APP membrane will have an overlaping of 100 mm on the end laps and 150 mm on side laps. The overlaping and joints will be thermo sealed with the propane torch complete all as specified and directed.

M&L for applying protective coating with aluminium paint @ 0.2 kg/sqm complete all as specified and directed.

M&L for cutting out cracks to "V" section in existing roofs or terracing, cleaning out, wetting, grouting, with cement and sand slurry 1:3 complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

Dismantling of old Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed

S&F of Pre painted galvalume aluminium zinc coating GI based corugated steel sheet 0.50mm thick Hi-Rib colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws as specified and directed.

S&F for Pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick Hi-Rib colour having tensile strength of 550 Mpa as in roof covering/cladding to wall/valley gutter fixed with self tapping screws as specified and directed.

S & F of rolled mild steel Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc Conforming to IS-1161-1979, 410-W (Gde-E250) complete all as specified and directed.

S & F of Mild steel plates, plain or chequered, 5mm thick or over in thickness in available sizes of Fe 410-W (Gde-E250) quality-A complete all as specified and directed.

S & F of mild steel Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S & F of mild steel Purpose made butt hinges conforming to Fe-290 Gde-E-165 suitable for fixing to stone/ concrete door and window frames complete all as specified and directed.

M&L for rolled mild steel FE-410-W (Gde.E-250) quality -B Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

M&L for rolled mild steel FE-410-W (Gde.E-250) quality -B, Joist, channel, angle, or tee sections, fixed independently without connecting plates, etc. (cut to ordinary lengths i.e. within 20 mm of the length indicated) complete all as specified and directed.

Dismantling removing all unsound concrete, plastered material by chipping/chiseling gently at all effected and adjoining areas of concrete etc till sound surface is reached all various locations in building (G+3) subsequently cleaning the surfaces by white brush and air blower and removing rubbish off the premises and disposing at the dumping site approved by local authorities complete all as specified and directed.

Removing of concrete all around reinforcement bar upto 12 mm dia and over from behind the reinforcing bars average 25mm (but not less than 15mm air gap)by manual methods (using wire brushing ,chiseling etc) and applying chloride free rust removing chemical on rusting steel reinforcement bar and removing all rust from steel reinforcement bar by emery paper and cleaning the area thoroughly by water and allow it to dry and totally rust free of reinforcement bar all as complete as per manufacturer's instruction as specified. Make of Rust removing chemical :- Reebaklens RR of FOSROC or equivalents solutions SIKA/STP.

Material, labour and preparation of existing reinforcement surface by brush and application of two component epoxy zincrich primer on existing reinforcement surface of minimum specific gravity 1.75, adhesive bond strength with steel is 1.50N/mm2 and maximum coverage area 5.00 Sqm per litre. complete all as specified and directed.

M&L for introducing new reinforcement bars upto 12 mm dia and over for structural connection in RCC beams, columns, lintel and slabs including power drilling holes of appropriate diameters in reinforced or plain cement concrete to a minimum depth of 150mm and upto 200mm including power drilling, fixing the reinforcement in position using epoxy, cleaning of loose dust by blowing air, sealing with epoxy cartridges etc complete all as specified and directed.

M&L for supply, mixing and placement of micro-concrete cement based prepacked single component chloride free, sulphate free, non-shrink, free flow. elf compacting, ready to use after mixing water in specified proportion of Sika Rep Microconcrete-4 or Renderoc-RG of Fosroc in required thickness as per manufacture's instruction and all as directed. Compressive strength (ASTN C 109,cm cube) of 35 MPa at 28 days including application curing compound concrete WB manufactured by Fosroc or equivalent at various locations in G+3 Bldgs including necessary form work complete all as per manufactures specification.

M&L for providing and applying at two component structural grade polymer modified reinforcement mortar Fosroc Renderoc S2 or equivalent product of SIKA upto a thickness of 15mm over a coat of epoxy resin bonding agent Nitobond EP. The cured mortar shall achieve a minimum compressive strength of 12N/mm2 in a day & 45 N/mm2 in 28 days with Flexural strength 8N/mm2 in 28 days Chloride diffusion coefficient shall be Nil after 24 hours when tested by Accelerated electrochemical chloride ion diffusion test method and the depth of carbonation shall be Nil after 24 hours when tested by Accelerated carbonation test. In addition to this percentage of water absorption should be 0.45 after 24 hours in immersion test at various locations in G+3 Bldgs complete all as per manufacture's specification.

M&L for applying of high efficiency polymeric resin base film forming curing agent/compound over concrete surface and maximum coverage area 5.00 Sqm per litre as per manufacturers instruction complete all as specified and directed. Make:- Concure LP90 of FOSROC or equivalents solutions of SIKA/STP/ Maruti / Choksey chemicals.

M&L for providing and applying a flexible expansion joint membrane of minimum 150mm wide and 1mm thick, expoband one (Expoband H45) of FOSROC or equivalent over the prepared joint using a two part epoxy adhesive nitobond PC 40 of Fosroc or equivalent. The minimum tensile strength of the membrane should be more than 12 N/mm2 and elongation at break should be more than 400%. The installation of the membrane should be carried out as per manufactures specification.

M&L for hoisting, assemble and fixing of double layer steel scaffolding to external perimeter of building duly cross braced and properly aligned for the functional aspect and safety of the building including dismantling, shifting & removal from site. Note: - Elevational area of the scaffolding facing the building shall be measured for payment.

S&F of shear connector of 8mm dia & requisite length on the surface to be repaired for the bonding between old and new concrete as per the locations instructed by the Engr-in-Charge. The shear connectors shall be of L shape and welded with existing reinforcement at least 100mm in length @ 200mm c/c both horizontally and vertical followed by coat of epoxy Zinc primer as per the specification.

M & L for providing and inserting mild steel shear key bars/levelling gauges of required length and diameter in reinforced/plain concrete for drilling suitable holes in RCC Slab/ wall/ column/ beams to a depth as directed for anchoring steel reinforcement bars including washing with water inserting lokfix 'E' of Fosroc or equivalent in the holes at various location in G+3 Bldgs complete all as per manufactures specification.

M&L for providing grouting in RCC walls and slabs by drilling holes @300 mm c/c upto half of the wall depth in zigzag manner using a drill machine and fixing a nozzle of 20mm dia, for injecting of cement or equivalent product till the refusal of injected grout material (grouting operation pressure shall be in between 2 to 4Kg per sq cm) followed by cutting the exposed nozzle so as to make the wall/ slab free from the grouting pipe and to seal the gap with polymer modified mortar.

M & L for PCC 1:2:4 Type B1 (20 mm graded stone aggregate) as in saucer drains, slope to be maintained as per site requirement complete in all respect as specified .

M&L for 75mm thick PCC (1:3:6), type C2 (using 40mm graded stone aggregate) as in plinth protection / paving, surface finished even & smooth with using extra cement complete as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of pink primer, on new wooden surfaces including preparation of surface exc 10 cm width or grith complete in all respect as specified and directed.

M&L for applying one coat of synthetic enamel paint, on old painted wooden surfaces exc.10cm width or girth including preparation of surface complete in all respect as specified and directed.

M&L for applying two Coats of Synthetic Enamel Paint over one coat of primer to steel and iron surfaces of any description over 10 cm width or girth not otherwise described, including preparation of new or previously untreated surface complete all as specified and directed.

M&L for applying one Coat of Synthetic Enamel Paint to steel and iron surfaces of any description, not otherwise described over 10 cm width or girth including preparation of Old painted surfaces surface complete all as specified and directed.

M&L for preparing newly plastered surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L for complete removal of old decorated surfaces and Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: old work (Two coats applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) complete all as specified & directed.

M&L for preparation of new plastered surfaces of wall and applying two coat of acrylic distemper complete all as specified and directed.

M&L for preparation of plastered and unplastered surfaces of old decorated walls and applying one coat of acrylic oil emulsion distemper complete all as specified and directed.

M&L for preparation of new plastered surface and applying three coats of white wash on ceiling complete all as specified and directed.

M&L for preparation of old plastered ceiling surface by complete removal of existing treatment and applying two coats of white wash complete all as specified and directed.

S&F 300mm bore salt-glazed stoneware drain pipe of grade 'A' laid in trenches and jointed in cement mortar and testing as specified including demolition of old pipes etc complete in all respect as specified and directed. Laying of saltglazed stoneware drain pipe shall be conforming to IS:4127(1983). Note:- (a) Necessary excavation and earthwork shall be measured and paid separately. (b) Quoted unit rate shall be deemed inclusive cost of all necessary fittings such as bends, junctions etc and extra joints, waste and cutting and testing as specified

All as per item No 139 here-in-before but for 200mm bore salt glazed stone ware drain pipes

M&L for concrete bed in PCC 1:3:6 type C2 (using 40mm graded stone aggregate) to drain pipes of 300 mm bore including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for concrete bed in PCC 1:3:6 type C2 (using 40mm graded stone aggregate) to drain pipes of 200 mm bore including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Excavation in trenches, n.exc 1.5m wide and n. Exc 1.5 m in depth for manholes, pier holes, cesspits etc n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in soft / loose soil complete all as specified and directed

Demolition for reinforced cement concrete as in cover slab or equivalent works including cutting reinforcement to facilate demolition complete all as specified and directed

M&L for RCPC factory made 75mm precast RCC cover slab of 3MT load bearing capacity conforming to IS: 12592 (Grade M-25) complete all as specified and directed

Returning, filling in incl spreading, levelling, watering and well ramming in layers not exceeding 25cm in soft / loose soil complete all as specified and directed

Removing excavated material of any description n.exc 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified and directed

Taking down carefully existing aluminium/copper point wiring (for light, fan, socket & power) alongwith fittings (switches, ceiling roses, tuve light fittings, bulk head fitting regulator, sockets, main switches, DB) complete, removing materials to store for keeping in sfe custody or for taking credit and refixing the serviceable items on original position (credit for above items should be made as per conditions separately) and making good the disturbed surfaces of walls, floors, ceilings etc to match with existing all as specified and directed.

M & L for concealed type point wiring for one light / fan / call bell point controlled by one switch,with 1.50 sqmm (nominal area) FRLSH insulated and unsheathed multi-stranded copper conductor cable 1100 Volts grade,single core,laid in and including PVC conduit complete with all fittings and accessories, fixed to walls/celling with sunk cast iron / pressed steel terminal boxes of size 1.6 mm thick conforming to IS - 5133(Part -I) with 3.0 mm thick plastic laminated sheet top cover (ISI Marked ) for mounting switches/ regulator / bell push etc including 1.50 Sqmm (nominal area) FRLSH PVC insulated and unsheathed multi stranded copper conductor cable 1100 Volts grade,single core, earth continuity conductor connected to common earth dolly complete all as specified and directed as in repair. Note:- Unit rate shall be included for cutting chases for conduits and sinking for boxes and making good to wall, floors etc

All as per item No 149 here-in-before but for one light point controlled by two way switch with 1.5 Sqmm cable complete all as specified and directed.

All as per item No 149 here-in-before but for 3 pin 6 Amps socket outlet on the same board with 1.5 Sqmm cable complete all as specified and directed.

All as per item No 149 here-in-before but for 3 pin 6 Amps switch socket combination on the independent board with 1.5 Sqmm cable complete all as specified and directed.

All as per item No 149 here-in-before but for switch socket combination 2 in 1, 3 pin 6/16 Amp on independent board with 2.5 Sqmm PVC unsheathed copper cable and 2.5 Sqmm copper conductor cable as earth continuity conductor complete all as specified and directed.

S&F of socket outlet 2 in 1, 5 pin 6 Amp, 230 volts as in repair

S&F of Switch socket combination 2 in 1, 5 pin 6 Amps, 240 Volts flush type as in repair

S&F of switch socket combination 2 in 1, 6/16 Amps, 230 Volts, flush type universal complete all as specified and directed

S&F of switch piano, flush type 6 Amps 230 Volts single pole, one way complete all as specified and directed

S&F of switch piano, flush type 6 Amps 230 Volts single pole, two way complete all as specified and directed

S&F of Ceiling rose surface bakelite three terminal 65x50mm, polycarbonate , isolated body complete all as specified and directed.

S&F of electronic fan regulator, flush type, humming with (step type) polycarbonate body suitable to control fan speed from 0 to 100% complete all as specified and directed

S&F of Bell, multi music type complete all as specified and directed.

S&F of bell push, flush button single pole 6 Amps 230 volts AC with polycarbonate body suitable to control speed complete all as specified and directed.

S&F of LED lights fitting 1 x 20 watt, 220 V, AC decorative box type with high efficiency PMMA diffuses soft glare free light with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose up to 1.5m length complete all as specifide and directed.

S&F of LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 Volt AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suiotable size complete all as specifide and directed.

S&F of LED bulb, B22 base, 9/10 watt, lumen output > 90 Lum / W, CRI > 70, 5700-6500K, Color temp, PF>0.9, THD < 20% suitable for lamp holder complete all as specified and directed

S&F of LED light fitting 1X9W / 1X10W bullkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed

S&F of LED fittings with lamps of 30 watts for bldg security light IP 66 power coated pressure die cast aluminium compact high power LED street light with compact size & rough design 32mm GI Bend complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor, 6.6 KV (Earthed) of size 120 Sqmm, 3.5 core complete all as specified and directed.

Supply, laying & testing cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 volts grade with stranded aluminium conductor, 6.6 KV (Earthed) of size 16.0 Sqmm, 4.0 core complete all as specified and directed.

M&L for sub main wiring with two single core PVC insulated, unsheathed, multistranded flexible copper conductor 1100 volts grade, FRLSH type, cables 6 Sqmm drawn through in and including rigid PVC heavy duty concealed conduits including 6 Sqmm 1100 volts grade, FRLSH type, PVC insulated and unsheathed multi stranded flexible copper conductor cable as continuous earth wire and connecting to common earth terminals complete all as specified and directed. Note:- (i) Three runs of cables drawn in conduit will be measured as one length of sub main (ii) PVC conduit and its accessories is deem to be included in unit quoted rate. (iii) Unit rate include for cutting chases for conduits and sinking for boxes and making good to wall, floors etc

All as per item No 170 here-in-before but of size 4.0 Sqmm complete all as specified and directed

All as per item No 170 here-in-before but of size 2.5 Sqmm complete all as specified and directed

S&F of MCB 'C' series, single pole, 6 to 32 Amps, 240 volts breaking capacity 10KA Complete all as directed.

S&F of MCB SPN, 16 to 32 Amps, 240 volts breaking capacity 10KA Complete all as directed.

S&F of MCB SPN, 40 to 63 Amps, 240 volts breaking capacity 10KA Complete all as directed.

S&F of MCB TPN, 63 Amps, 415 volts breaking capacity 10KA Complete all as directed.

S&F of MCB DB SPN (double door) 8 ways including copper bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good the disturbed surfacesof wall Complete all as specified and directed.

S&F of MCB DB TPN (double door) 4 ways including copper bus bar neutral link, earth bar and din rail, recessed with wall surfaces by chase cutting and making good the disturbed surfacesof wall Complete all as specified and directed.

Taking down unserviceable rusted / damaged MCB DBs of any type and way along with any type MCB for fixing of new or old and making good to the disturbed surfaces of walls etc complete all as specified and directed.

Taking down ceiling / Exhaust fan, Sealing cable end, Dismantling blades and removing fan blades deposit to store for safe custody and refixing at the same position, connection after repairing, greasing, changing of bearing / capacitor if required complete all as specified and directed

M & L for painting of exhaust fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filer, one coat after cleaning all dust etc complete all as specified and directed

M & L for Earthing complete with galvanized steel earth plate electrode 600x600x6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to 4.0mm GI wire (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no 5 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia 150mm long reinforcement, watering funnel, 40 mm dia light grade for protection of earth electrode 20 mm dia for watering all as specified and directed and tested on completion including taking down / up existing one.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs 73,621.00 mentioned on Page No 45 shall be deducted from the total quoted amount of BOQ.

KWALITY CONSTRUCTION (BID ID -3115070)

S.M.CONSTRUCTIONS (BID ID -3124229)

NIRMAL SALES CORPORATION (BID ID -3124073)

BHASKAR SUPPLY AGENCY (BID ID -3122896)

DNS CONSTRUCTION COMPANY (BID ID -3122591)