GE/PNH-13/2021-22

Amount

B&R PORTION:- Preparation of old plastered/ un-plastered wall surfaces including brooming down or steel wire brushing, scraping down, smoke soot, mould, moss, efflorescent salts, trading oil and greasy spots, and applying one coat of white wash on walls including cornices, pilasters etc, complete all as specified and directed.

Complete removal of existing treatement and applying two coats of white wash on wall, complete all as specified and directed.

All as per item No. 01 above, but on ceiling, complete all as specified and directed.

All as per item No-01 above but applying one coat of colour wash on walls, complete all as specified and directed.

All as per item No-01 above but applying one coat of oil bound distemper white or any tint, complete all as specified and directed.

Complete removal of existing treatement from wall plaster and applying two coats of oil bound distemper white or any tint, complete all as specified and directed.

All as per item No-01 above but applying one coat of cement base paint on wall and AC sheet roof surfaces, complete all as specified and directed.

Complete removal of existing treatement from wall plaster and applying two coats of cement base paint, complete all as specified and directed.

M&L for Preparation of old painted steel surfaces of any description not otherwise described, over 10cm width or girth and applying one coat of synthetic enamel paint in camouflage pattern/single shade, complete all as specified and directed.

M&L for Preparation of old painted wooden or wood based surfaces of any description not otherwise described, over 10cm width or girth including knotting and stopping as required and applying one coat of synthetic enamel paint, complete all as specified and directed.

Complete removal of existing treatment of the walls / preparation of new plastered surface and applying wall putty of approved make not less than 1mm thick on walls as per manufacturar instructions with and including rubbing by means of sand paper to have smooth finishing to receive primer / paint, complete all as specified and directed.

Writing letters or figures (Block, Roman, Italic or Indian) n. exc 30cm high with synthetic enamel paint including oblitering old writing of any description to match existing work, complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level), complete all as specified and directed.

Dismantling floor, hearth, or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking down cement plaster of any description on stone or brick walls etc including racking out joints, hacking for key scrubbing down with water etc. complete all as specified and directed.

M&L for 25 mm thick PCC 1:2:4 type B-0 (using 12.50mm graded crushed stone aggregate) as in sub base floor finishing surface even and fair, complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) any thickness including cover fillets complete all as specified and directed.

S&F Suspended false ceiling using E- grid suspended ceiling grid system of grid size 600x600mm with GI frame work of main runner 38 x 24mm sheet thickness 0.4mm, cross Tee 28 x 24mm sheet thickness 0.3mm and wall angle 24 x 24mm x 0.4mm using 4mm thick high pressure stream cured classic variant E-board, designer pattern (ISI marked, IS No 14862-2000) & E board to be placed in the grid suspended by 4mm GI wire hangers from the purlins of the roof with butter fly clips, complete all as specified and directed. Make:- Everest Industries Ltd or equivalent make mentioned in Appx 'A' to P.S. as approved by GE.

M&L for Chequered cement concrete tiles 200x200x 20-25mm thick as in floors, set, jointed and pointed in white cement slurry and pigment to match shed of tiles, laid over and including 20mm thick screed bed in CM 1:6, complete all as specified and directed.

M&L for Vitrified ceramic tiles 10 mm thick (square/rectangular) area of each tile but not exceeding 0.36sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

All as per ser item No.20 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc 0.11Sqm but n exc. 0.18Sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles, laid over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

All as per ser item No.22 above but as in vertical surfaces of wall such as in dado/skirting etc. fixed over & including 10mm thick plaster in CM 1:4, complete all as specified and directed.

M&L for Non skid coloured ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06sqm but not exceeding 0.11sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shed of tiles, over and including 15mm thick screed bed in CM (1:6), complete all as specified and directed.

M&L for Glazed ceramic coloured tiles (300x200mm) x 7mm thick, as in vertical surfaces such as in skirting and dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles over and including 10mm thick back coat layer in cement mortar 1:4, complete all as specified and directed by Engr-In-Charge.

M&L for Plain cement concrete 1:3:6 type C-1(using 20mm graded crushed stone aggregate) as in surface channels and drains, complete all as specified and directed.

M&L for 50mm thick PCC 1:3:6 Type C-1 (using 20mm graded crushed stone aggregates) laid in alternate bays (not exceeding 2 sqm each) as in plinth protection, finished the surfaces even & fair, filled with mastic filling comprising one part of bitumen 85/25 grade and three parts of sand by weight complete all as specified and directed.

Demolition of brick or stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work, complete complete all as specified and directed.

M&L for Brick work with sub class ‘B’ bricks straight or curved on plan exc 6m mean radius, built in cement mortar (1:6), complete all as specified and directed.

M&L for Walling of random rubble stone masonry brought upto course, well bonded, bedded and solidly hearted, built in cement mortar (1:4), complete all as specified and directed.

M&L for Rendering 20mm thick on other than fair faces of brick work or stone masonry surfaces in cement mortar 1:4 and finished the surface even and smooth without using extra cement , complete all as specified and directed.

M&L for 15mm thick cement plaster rendering in CM 1:4 on fair faces of bricks or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for 15mm thick rendering in CM 1:6 on other than fair faces of brick or concrete surfaces & finishing the surface even and smooth without using extra cement, complete all as specified and directed.

M&L for Cement concrete (1:2:4) type-B-1 (using 20mm graded stone crushed aggregate) as in lintels upto 1.5 metre clear span, cills, steps, siesmic and other similar bands, plinth courses, string courses, lacing courses, parapets and railing upto 60cm height, copings, bed block, kneelers, apex stones, bed plates, roof kerbs round or chamfered on edges, water troughs and the like including weathering, slightly rounded or chamfered angles and throatings etc.including necessary form work complete all as specified and directed by Engineer-in-Charge.

M&L for Preparation of newly plastered or unplastered surfaces of wall and applying two coats of cement base paint, complete all as specified and directed.

M&L for Applying three coats of white wash including preparation of newly plastered surfaces of wall complete all as specified and directed.

M&L for Preparation of newly plastered surface of wall including cornices pilaster etc, and applying two coats of oil emulsion distemper over and including 1-2mm thick wall care putty, complete all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness including Nainital or similar pattern roof covering, complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description complete all as specified and directed.

S&F 0.63mm thick galvanised corrugated mild steel sheeting with grade of Zinc coating of 275 gms/Sqm with two corrugation side lap and at least 150 mm end lap , fixed with L or J type or cranked hook bolts, in roof, walls etc, complete all as specified and directed.

All as per item No. 40 above, but except sheeting, complete all as specified and directed.

S&F 0.80mm thick plain galvanised mild steel sheeting with 275 gm/sqm Zinc coating as in ridge , hips, valley gutters, drip and straight flashingfixed with L or J type or cranked hook bolts, in roof etc., complete all as specified and directed.

S&F Rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connected plate confirming to Fe 410W(Gde E-250), quality 'A' complete all as specified and directed.

S&F Mild steel work as in wind ties for roof including securing bolts, including all necessary drilling, bolting or riveting etc. fixed in repairs, and similar work conforming to Fe-250 Gde E-165 complete all as specified and directed.

Taking up or down steel tubing of 15mm bore pipe and connection laid in trenches or floors or fixed to walls and including cleaning for refixing or removal to store with all fittings, complete all as specified and directed.

S&F Steel water tubing of 15 mm bore ‘medium grade’ galvanized with all fittings like socket, union, elbow, bend, tees etc fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F in repair Bib tap 15 mm bore with flange, Brass CP, fancy type. with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule complete all as specified and directed. Make:- Jaquar cat part No CON-047KN or equivalent cat part of make as specified in P.S.

S&F in repair Angular stop valves cast copper alloy 15 mm dia, fancy type, chromium plated with wall flange screwed down, high pressure, with capstan handle screwed both ends for iron pipes or for unions complete all as specified and directed. Make-Jaquar Cat Part No:-CON-059KN or Equaivalent cat part of make as specified in P.S.

S&F in repair Vitreous china squatting pan (Orissa pattern) size 580 x 440 mm, snow white, with 'P' or 's' trap, front or back inlet and integral foot rests, complete connection to drain (outgoing pipe) and to flushing pipe and syphonage pipe etc. including lime concrete bedding, complete all as specified and directed.

S&F in repair Vitreous china wash hand basin, white, flat back, size 550x400 mm excluding taps, waste, chain & plug and porcelain stopper but including brass chromium plated waste coupling, and waste pipe PVC 32mm dia including cutting for and pinning in ends of brackets or erecting stand etc complete all as specified and directed.

S&F in repair PVC valve less symphonic action type flushing cistern 10ltr capacity , low level white with inlet ball valve float and handle including brackets including 32mm dia PVC. flush pipe for low level cistern including all joints complete all as specified and directed. Make:- Prayag cat part No 501 or equivalent cat part of make as specified in Appx 'A' to P.S..

S&F in repair PVC connection 15mm size with PTMT nuts on both ends of length 450mm complete all as specified and directed.

S&F in repair 15mm bore pillar tap cast copper alloy with capstan head, fancy type, chromium plated, screwed down, high pressure, with or without lettered 'Hot or Cold' with long screwed for iron pipe complete all as specified and directed. Make:- Jaquar cat part No-CON-011KN or equivalent cat part of make as specified in P.S.

Taking down shutters of any description exceeding 1sqm and not exceeding 2sqm each, complete all as specified and directed.

Taking down chowkats or frame with shutters (without taking off shutters from the frames) area not exceeding 1.5Sqm each, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5Sqm and not exceeding 4Sqm each, complete all as specified and directed.

S&F 2nd class hard wood, plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, complete all as specified and directed.

S&F 35mm thick 2nd class hardt wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc divided into square (with sash bars) edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a) supplied and fitted to chowkats complete all as specified and directed.

S&F 35mm thick 2nd class hard wood plain, framed, panelled door shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of 12mm thick veneered particle board medium density, wood particle board with commercial face veneers, complete all as specified and directed.

S&F 30mm thick 2nd classhard wood Glazed and skelton shutters, open rebated and prepared to receive glass, gauge etc divided into square (with sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitered beads for securing glass etc. size of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (b) supplied and fitted to chowkats complete all as specified and directed.

S&F Mild steel butt hinges, medium weight, cold rolled,100mm long, complete all as specified and directed.

S&F Mild steel butt hinges, medium weight, cold rolled,75mm long, complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of extruded section of size 150mm and fixed, complete all as specified and directed.

S&F Aluminium anodised, barrel tower bolts of extruded section of size 100mm and fixed, complete all as specified and directed.

S&F Aluminium alloy handles, cast type, anodised of size 150mm and fixed, complete all as specified and directed.

S&F Aluminium alloy handles, cast type, anodised of size 100mm and fixed, complete all as specified and directed.

S&F 250mm long aluminium alloy anodized sliding door with haps, staple (bolt type) and fixing clips of sheets, cast or extrusted sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy complete all as specified and directed.

S&F in repair Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beading, complete all as specified and directed.

S&F 300mm Mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed.

M&L for Preparation of new wooden surfaces of any description, not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint of Ist quality over a coat of pink primer, complete all as specified and directed.

M&L for Applying two coats of synthetic enamel paint of Ist quality over a coat of red oxide primer to new or previously untreated steel surfaces over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden / steel frames or stone/ concrete, glazed with putty or fixed with beads, complete all as specified and directed.

Dismantling PVC water tanks and removing to storing of capacity not exceeding 500 ltr, complete all as specified and directed.

Dismantling PVC water tanks and removing to storing of capacity exceeding 500 ltr and not exceeding 1000 ltr, complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 500 Ltrs incl with 15mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks triple layer (Cylindrical vertical with closed top) hoisted and fixed in position all as spd in SSR Pt-I, of capacity 1000 Ltrs incl with 20mm Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F Sheet glass ordinary quality, 3mm thick, glazing with oil putty or wooden beads in squares not exceeding 0.50Sqm in each pane, complete all as specified and directed.

Cleaning of under ground sewage lines of 100mm/ 150 mm bore including manholes, gully traps etc. by means of cleaning by roding from manholes to manholes and flushing after cleaning, taking out sludge collected in manholes, removing & depositing the same outside the periphery of defence land in the pit at a minimum distance of 50 m from nearby living accn and covering the sludge in pit with earth and finally spraying unslaked lime, dry, around the manholes and cover the pit, complete all as specified and directed. Note:-Cost of Taking out sludge, transporting of sludge out side the defence land, earth work & deposition in the pit is deemed to be included in the unit rate to be quoted by tenderer.

Dewatering contaminated with fine waste materials ( liquid sludge) from septic tank and soakage well/pit of any capacity/depth by mechanical pumping (Truck mounted mechanical machine) and depositing the same outside the periphery of defence land at a minimum distance of 50 m from nearby living accn and burring in borrow pits including covering with fresh mud including taking off manhole covers and refixing the same after cleaning/ removing the liquid waste material of septic tanks / soakage pits and making it fully functional with & including cutting holes through slab/ wall where required for inserting pipe and making good the same with cement mortar to match with existing surfaces complete all as specified and directed by Engr-in-Charge (Qty of liquid sludge depth shall be measured for payment).

Cleaning of blockage of Water Closet (Indian or European), trap & pipe line upto first manhole manually by Roding and making it fully functional by flushing with water including removing the deposited sludge/solid/liquid material, outside MD land and burring in borrow pits including covering with fresh mud, complete all as specified and directed by Engineer-in-charge.

Taking up/down drain pipe, vent pipe, soil waste pipe (salt glazed ware, AC, PVC or reinforcement concrete) of size 100/75mm set in cement mortar/ concrete from walls / trenches, complete all as specified and directed.

S&F PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint laid in trenches/floors as soil pipe(vent pipe fixed, complete all as specified and directed.

S&F PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint laid in trenches/floors as soil pipe(vent pipe fixed, complete all as specified and directed.

S&F PVC (SWR) pipes 110mm dia any length single socketed with rubber ring joint fixed to walls as soil pipe with & including clamps, complete all as specified and directed.

S&F PVC (SWR) pipes 75mm dia any length single socketed with rubber ring joint fixed to walls as soil pipe with & including clamps, complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore complete all as specified and directed.

S&F PVC (SWR) junction single (single T) 110mm bore equal or unequal, fixed, complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm bore complete all as specified and directed.

S&F 75mm PVC (SWR) junction single, (single T) equal or unequal provided with access door complete all as specified and directed.

E&M PORTION:- Taking down carefully copper/ aluminium unserviceable/ perished point wiring (light, fan, socket or power complete including fixture and fittings such as switches, ceiling roses, pandents, regulators, sockets, light fittings,removing material from site for taking credit etc and making good disturbed surfaces of wall, floors, complete all as specifiecd and directed.

Point wiring with two single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable and one single core 1.5 Sqmm (nominal cross section area) FRLS PVC insulated unsheathed multistranded copper conductor cable as earth continuity to common earth and connecting to earth dolly running in and including PVC casing & caping (ISI marked) of suitable size with PVC boards of appropriate sizes and all requisite accessories such as PVC elbow, Tee, collars, bends etc. with PVC terminals box & cover for mounting swtches, sockets, fan regulator etc for mounting switches, sockets, fan regulators etc complete all as specified and as directed for the following :-

One light/fan point controlled by one way switch 6 Amp complete all as specified and directed.

One 3/5 pin socket outlet 6 amp on same board complete all as specified and directed.

One 3/5 pin socket outlet 6 amp independent board complete all as specified and directed.

One bell point controlled by one way switch 6 Amp complete all as specified and directed.

All as per srl item No 91 here in before but for one 3 pin socket outlet 16/20 Amp independent with two single core 2.5 Sqmm size cable as phase & neutral and one single core 1.5 Sqmm as in continuous earth wire complete all as specified and directed. Make of wiring wire against item No- 91 to 92: Havells/RR Kabel/Finolex

S&F in repair Ceiling rose, 3 phase PVC/poly carbonate, insulated body, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Switch piano flush type 6 Amp single pole one way, (ISI marked), complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Switch piano bell push flush type 5 Amp single pole one way (ISI marked) complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Switch socket multipurpose combination 2 in 1, 5 pin, 6 Amp flush type universal, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Switch socket outlet multipurpose combination 2 in 1, 6 pin, 5 and 15 Amp flush type universal, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Stepped type electronic fan regulator flush type on the existing phenolic laminated sheet etc. for 1200 / 1400mm sweep, complete all as specified and directed. Make:-Havells/Anchor/Legrand

S&F in repair Electric bell ding dong type 230 volts AC supply 50 Hz complete all as specified and directed by Engineer-in-Charge. Make:-Havells/Anchor/Legrand

S&F in repair Tube light fitting box type suitable for LED 20W tube rod made out of ultra bright, glass shell, glare free, wide angle, single side connection retofit LED tube with G13 lamp holders complete with hosing with all accessories pre wired and making connection with copper flexible cable of appropriate size from ceiling rose to light fitting including 20LED tube rod 4 feet long with single side connection complete all as specified and directed. Make:-Havells Cat Part No:-LHLDEFXD5L8R020 for LED tube rod & Cat Part No:-LHFXCEP1TNNW020 for batten fittings or Equivalent cat part of make:-Wipro / Crompton / Bajaj Note :- The LED batten and LED tube rod shall be of same make.

S&F in repair LED lamp CDL 10 watt with holder base (B22) type, complete all as specified and directed. Make of LED lamp:- Havells cat part No LHLDEUEEML8R010 or Equivalent cat part of make as specified in Appx 'A' to P.S.

S&F in repair Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 4 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed. Make:- Havells cat part No-DHDPSHODPW04 or Equivalent cat part of make specified in PS.

S&F in repair Sheet metal enclosure factory made (Double door) for DBs, single pole and neutral, 240 volts, 8 way with 200Amps rated bus bar fixed on walls, including connecting both incoming and outgoing cable termination with proper taping, lagging testing and commissioning complete all as specified and directed. Make:- Havells cat part No-DHDPSHODPW08 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB SPN 40-63 amps 415 volts 10 KA 'C' series, complete all as specified and directed. Make:-Havells cat part No- DHMGCSNF040 - DHMGCSNF063 or Equivalent cat part of make as specified in P.S.

S&F in repair MCB single pole 6 to 32 amps 240 volts 10 KA 'C' series complete all as specified and directed. Make:-Havells cat part No-DHMGCSPF006-032 or Equivalent cat part of make as specified in P.S.

Earthing complete with galvanized steel earth plate electrode 60cmx 60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below normal ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0mm dia by means of bolts, nuts and washers of galvanized iron or steel, protected by GI light grade pipe 15mm bore including GI light grade water pipe 20mm dia with funnel all as shown in electric plate No. 3 of 2009 SSR Pt-I and testing complete including earth work in any type of soil, PCC 1:2:4 type B-1 as in earthing pit and cover 50mm thick reinforced with 6mm dia MS round bar @ 10cm C/C both way and MS frame, common salt, charcoal and testing on completion including dismantling unsv earthing, complete all as specified and directed.

S&F Sub main wiring with single core cable 2x 6 sq mm FRLS insulated unsheathed stranded copper conductor cable 1100 Volts grade including surface PVC casing caping medium grade alongwith 1x 4 Sq mm FRLS insulated unsheathed copper conductor cable as earth wire connected with main earth dolly including taking down old unsv sub main wiring of any type, complete all as specified and directed. Note:-2 wire of 6 sqmm, 1 wire of 4 sqmm and one run of pvc conduit/casing caping shall be measured as one unit.

S&F 1100 volts grade heavy duty cable PVC insulated solid aluminium conductor served with PVC tape and over all PVC sheathed in service connections suspended by insulating hangers not more than 1 m apart including 4mm dia GI suspension wire, one twin core cable flat or circular of size 6 Sqmm with & including taking down old old unsv service cable connection, complete all as specified and directed.

Repair and maintenance of unserviceable ceiling fan of 1200mm/1400mm sweep at contractor's work shop, incl dismantling complete the ceiling fan parts, inspecting serviceability of all the parts, refixing of serviceable parts after cleaning and replacement of unserviceable parts with company's genuine parts i.e. capacitor, bearing, bushes, shaft, bracket, rubber bush, connecting wire, PVC connector, aluminium clamp for rod, bracket, bush rod, greasing/oiling etc assembling, cleaning and testing of ceiling fan complete all as specified and directed. Note: (i) Unserviceable parts as above shall be measured and paid separately under relevant items of Sch 'A' as supply only. (ii) Rewinding of stator will be measured & paid for separately under relevant item of Sch 'A'. (iii) Cost of minor part i.e. Cotter pin, screws shall be deemed to included in the cost of quoted rate.

S&F in repair bearing good quality for ceiling fan 1200mm/1400mm sweep ISI marked complete all as specified and directed.

S&F in repair Gun metal bush for ceiling fan 1200mm/1400mm sweep complete all as specified and directed.

S&F in repair capacitor 2.5 mfd ISI marked complete all as specified and directed.

M&L for removing of old burnt winding of any size , type and rewinding of stator winding with superior quality copper wire with insulation complete all as specified and directed.

M&L for Painting of ceiling fans complete, in situ with synthetic enamel paint by spraying including filling cavities with filler, one coat after cleaning all dust etc complete all as specified and directed.

M&L for disconnecting elect & water connection to geyser of cap 25/50/35 ltr, taking down, from existing position, dismantling and inspecting all the parts, for its serviceability, cleaning of serviceable parts i.e. Heating elemet, base assy, connecting lead, thermostat, electrical contact, electric wiring, indicators, safety valves etc and refixing, replacement of unserviceable parts, re assembling, remounting, reconnecting with electrical & water connectionn and testing complete all as specified and directed. Notes: (i) The defective parts to be replaced shall be measured and paid separately under relevant item of Sch 'A' as supply only. (ii) Cost of minor items i.e. Screws, nut & bolts etc shall be deemed to be included in the above item.

S&F in repair heating element 2.0 KW, ISI marked with gasket suitable for as existing size, type and make of geyser complete all as specified and directed.

All as per item No 153 above but of cap 1.5 KW complete all as specified and directed.

S&F in repair thermostat ISI marked suitable for existing make of the geyser under repair of cap 50/25 /35 Ltrs complete all as specified and directed.

S&F in repair geyser pipe connection heavy duty for inlet, outlet connection suitable to withstand the pressure and temperature for existing geyser complete all as specified and directed.

M&L for complete servicing and repair of DG set capacity 62.5 KVA including replacement of Engine oil and all types of filters as per manufacturers manual and as directed by Engineer in Charge. NOTES: - (i) Engine oil, oil filter, coolant replacement will be measured and paid separelty under revelant item. (ii) 'B' check shall be carried out by the authorised dealer of kirloskar/ Crompton Greaves and certificate of 'B' check shall be produced by the contractor from authorised dealer of Kirloskar / Crompton Greaves (iii) Testing equipments required for `B' check shall be of contractor's responsibility.

Supply only Special engine oil 20 W 40 grade all as recommended by manufacturer for first filling in the new DG sets complete all as specified and directed. Make: Kirloskar/ Castrol

M&L for Coolant concentrate for filling in radiator of DG set complete all as specified and directed. Make of coolan : Castrol or equivalent make as approved by GE.

M&L for cleaning of radiator assy by means of dismentalling from engine completely, flushing out complete old coolant/water ,cleaning by chemical wash , soldering /brazing complete and reassembling the same to the engine for smooth and efficiant functioning complete all as specified and directed.

Lubricant oil filter element suitable for engine which has to be repaired at site/workshop complete all as specified and directed by Engineer-in-Charge.

Fuel filter suitable for engine which has to be repaired at site/workshop complete all as specified and directed by Engineer-in-Charge.

Fuel filter housing suitable for engine which has to be repaired at site/workshop complete all as specified and directed by Engineer-in-Charge.

Belt suitable for engine which has to be repaired at site/workshop complete all as specified and directed by Engineer-in-Charge.

Hose for air cleaner including hose clips suitable for engine which has to be repaired at site/workshop complete all as specified and directed by Engineer-in-Charge.

M&L for complete servicing and repair of Refrigerator/ Deep Freezer of any capacity, servicing and cleaning of all accessories, oiling of fan motor, checking of wiring connections, and re-fixing in the same in position testing complete all as specified and directed by Engr-in-Charge. (Unsv accessories will be measured and paid seperately under respective items of Sch )

Supply only the following items required to incorporate in item No 130 above:-

Auto cut thermostate switch for Refrigerator defrosts type complete all as specified and directed by Engr-in-Charge.

Overload protectors for Regrigerations upto 310 Ltrs capacity complete all as specified and directed by Engr-in-Charge.

Relays suitable for Refrigerators upto 310 ltr capacity complete all as specified and directed by Engr-in-Charge.

Supply only door switch for refrigerator complete all as specified and directed by Engr-in-Charge.

Supply and filling gas charging required to the system of suitable type R-34/12/32 /R22 or as per existing at site complete all as specified and directed by Engr-in-Charge.

Supply and filling gas charging required to the system of suitable type 134a or as per existing at site complete all as specified and directed by Engr-in-Charge.

M&L for complete servicing and repair of RO Plant of any capacity, servicing and cleaning of all accessories and re-fixing in the same in position, testing complete all as specified and directed by Engr-in-Charge. (Unsv accessories will be measured and paid seperately under respective items of Sch).

S&F micron cartridge filter sponge 4.5" x 20" of 4 micron complete all as specified and directed.

RO antiscalant chemical minimum 5 liter can complete all as specified and directed by Engr-in-Charge.