Establishment of food processing Unit at KVK Samba

Earthwork in excavation by mechanical means (Hydraulic excavator)/mannual means in foundation trenches or drains ( not exceeding 1.5 m in width or 10 Sq. m on plan), including dressing of sides & remaining of bottoms , lift upto 1.5 m , including getting out the excavated soil and disposal of surplus excavated soil as directed , within a lead of 50 m

All kinds of soil.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:5:10 (1 cement : 5 fine sand(zone-III) : 10 graded stone aggregate 40 mm nominal size)

1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor, etc., up to floor five level, excluding the cost of centering, shuttering and finishing :

1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size)

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation leveling and dressing and finishing the top smooth.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(Zone III) : 4 graded stone aggregate 12.5mm nominal size).

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns,walls, etc. for mass concrete.

Edges of slabs and breaks in floors and walls.

Under 20 cm wide

Columns, Pillars, Piers, Abutments, Posts and Struts.

Suspended floors, roofs, landings, balconies and access platform.

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete up to plinth level.

Cold twisted/TMT bars

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :

Cement mortar 1: 6 (1 cement: 6 coarse sand)

Extra for brick work with common burnt clay bricks/cement concrete bricks in superstructure above plinth level upto floor five level

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2mm and braced with flat iron diagonals 20x5 mm size,with top and bottom rail of T-iron 40x40x6mm, with 40mm dia, steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer,

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting , hoisting , fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete

Hot finished welded type tubes

Providing and fixing 18mm thick gang saw cut mirror polished premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20mm thick base cement mortar 1:4 (1 cement : 4 coarse sand) joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Granite of any colour and shade

Area of slab over 0.50 sqm.

Providing and fixing of 40 mm granite moulding on top of granite walls/dados, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing and laying Vitrified floor tiles (600x600 mm) with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours and shades laid over 20 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), including grouting the joint with white cement and matching pigments etc. complete.

Providing gola 75x75mm in cement concrete 1:2:4 (1 cement :2 coarse sand : 4 stone aggregate 10 mm and down gauge) including finishing with cement mortar 1:3(1 cement : 3 fine sand) as per standard design

In 75x75mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1mx1mx400 micron, finished with 12mm cement plaster 1:3 (1 cement :3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

12 mm cement plaster of mix :

1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall finished with a floating coat of neat cement of mix :

1:6 (1 cement: 6 fine sand)

6 mm cement plaster of mix :

1:3 (1 cement: 3 fine sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade.

New work (two or more coats) over and including water thinnable priming coat with cement primer.

Finishing walls with Acrylic exterior paint of required shade :

New work (Two or more coat over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm).

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :

Two or more coats on new work.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Kitchen sink without drain board

610x460mm bowl depth 200mm

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C waste fittings complete:

Flexible pipe

32 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Circular tank

Providing and fixing following PVC pipes alongwith necessary assesories and fitting (such as tee, elbow, bends etc )complete items

PVC pipe (100 mm nominal dia)

Providing and fixing 100 mm CP grating.

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS : 8931

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

15 mm nominal bore.

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. : Internal work – Exposed on wall.

15 mm dia. nominal bore

20 mm dia. nominal bore

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c trenching and refilling.

25 mm dia. nominal bore

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size),foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design.

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (medium duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and laying RBM (River Bed Material) including loading, carrying, unloading, spreading, compacting and watering complete item.

Providing and injecting chemical emulsion for pre/post constructional Anti-termite treatment, creating continuous chemical barrier under and around the column pits, walls, trenches, basement excavation,top surface of the plinth filling, junction of wall and floor,along the external perimeter of building,expansion joints, over the top surface of consolidated earth on which apron is to be laid, surrounding of pipe and conduits with chloropyriphos emulsifiable concentrates of 20% concentration, including cost of chemical, diluting in water to 1% concentration, labour, HOM of equipments, complete as per specifications.(plinth area of building at ground floor only shall be measured).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For fixed portion

Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

With float glass panes of 5.00 mm thickness

Providing and fixing wire gauge in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):

Providing and fixing anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P brass/ stainless steel screws @ 200mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge. (Only weight of grill to be measured for payment)

Providing and fixing aluminium lock handles for aluminium sliding shutters.

Providing and fixing 6 amps to 32 amps rating 240 volts, 'L' series, miniature circuit breaker of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as reqired (category B)

Single Pole

Supply and fixing of following rating, 2P 230 volts, SPN in the existing MCB DB complete with connections, testing and commissiong etc. as required

40 amps SPN

Supply and fixing 1x20 watt with extruded aluminium tube light including connection testing etc. as reqd. (CCS-103-20-65-SL-DP-NWH) or equivalent in Wipro, Philips.

Supply and fixing of 18 Watt LED recess panel aluminium housing with all accessories including connection testing etc as reqd.

Wiring for light / fan / exhaust fan / call bell point with 1.5 Sq mm FR PVC insulated copper conductor cable in surface / recessed ISI marked PVC conduit with modular switch, modulr plate, suitable GI box and earthing the point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable etc. as required.

Light point on board with copper wiring in ISI marked PVC conduit wiring for 3 Pin 6 amp plug point with 1.5sqmm PVC insulated multistrand copper conductor cable including P/F of 3 Pin 6 amp modular switch socket outlet on switch board in surfaced recessed PVC conduit wiring system and 6 amp switch, earth the 3 pin as required with 01 No. PVIC insulated green colour wire.

Wiring for light plug with 2 x 2.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x 2.5 mm copper wire for loop earthing required

Wiring for power plug with 2 x 4 sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked PVC conduit along with 1x4.0 Sq mm copper wire for loop earthing as required

Wiring for 1x 1.5sq.mm. ISI marked PVC insulated copper conductor single core cable in surface / recessed ISI marked in the existing PVC conduit etc. as required ( Invertor wiring )

Supply and fixing of 25 mm dia PVC conduit alongwith accessories in surface/recess.

Supply and fixing of 32 mm dia PVC conduit alongwith accessories in surface/recess.

Supply and laying of 10 mmx2 core aluminium wire complete with all accessories

Supplying and fixing suitable G.I. box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 15/16 Ampere and 5/6 Ampere modular socket outlet and 15/16 Ampere modular switch, connection testing etc as reqd.

Supply and fixing of the following way, single pole and neutral / three pole and neutral, sheet steel, double door, phase segregation type, MCB distribution board, 230V / 415V on surface/recess, complete with tinned copper bus bar, neutral bus bar and link, earth bar, din bar, detachable gland plate, interconnections, including painting, earthing, etc., as required.

12 way SPN DB

Supply and fixing of 70 watt LED street light fixture including dismantling of existing with connection testing etc as reqd.

Please Enable Macros to View BoQ information