Construction of first floor of building for farm machinery testing lab facilities (consisting of six rooms, lab, seminar hall, toilets, corridors and stairs etc.) in the premises of College of Agricultural Engineering and Technology at CCSHAU, Hisar

Amount

Civil work 1 to 65:- Dismantling brick work, tile masonry or tile lining and tile terracing {HSR 8.5(b)} (b) in cement

Dismantling concrete (HSR 8.6(b)} (b) cement concrete plain of 1:4:8 or leaner mix

Dismantling roofing (HSR 8.8(g)} (g) demolishing mud phaska in tile terracing

Extra for smooth exposed concrete finish as desired which is not to be touched or plastered but is to be left as it comes out of the shutting for corbel, parapets, fascias and other similar items.(45% labour rate of item No. 9.11)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size in first storey upto 4 metres above plinth level (HSR 10.59 + Note} (at first floor)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in shelves excluding steel reinforcement, but including centring and shuttering, laid in position, complete in all respects. (HSR 10.81 + Note) First floor

CCement concrete 1:2:4 with stone aggregate 20mm nominal size for reinforced concrete work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement , but including centring and shuttering, laid in position , complete in all respects (HSR 10.82 + Note) i) first floor

ii) Second floor (HSR 10.82+note)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work for walls exceeding 20 cm thickness (straight and curved) beams, girders, stairs, columns,(square or rectangular) battens and lintels etc., excluding steel reinforcement but including centring and shuttering, laid in position, complete in all respects.(HSR 10.86)

Cement concrete 1:2:4 with stone aggregate 20 mm nominal size for reinforced concrete work in fascias parapets and other thin vertical sections, not covered by item nos. 10.82,10.86 to 10.88 not exceeding 10 cm thickness excluding steel reinforcement but including centring and shuttering , laid in position, complete in all respects. (HSR 10.89)

Extra over item Nos. 10.79 to 10.94 , if 1:1.5:3 mix is used, instead of 1:2:4 {HSR 10.95(a)}

First class brick work laid in cement sand mortar 1:6 in first storey upto 4 metres above plinth level (HSR 11.7+note) i) first floor

ii) Second floor (HSR 11.7+note)

11.43 cm thick brick wall with every fourth course reinforced with hoop-iron laid in 1:4 cement stone dust (from crusher) mortar in superstructure (HSR 11.51+note)

11.43 cm thick brick wall laid in cement stone dust (from crusher) mortar 1:4 without reinforcement in foundation and plinth. {HSR 11.52+note)

Providing 5.72 cm brick dalli facing with brick size 22.86 cm X 11.43 cm X 5.72 cm thick to be obtained after cutting of bricks laid in cement sand mortar 1:3 on RCC lintels, beams fascia etc. including centring and shuttering complete (HSR 11.98+ Note) (i) first floor

Terracing consisting of tiles 22.86 cm X 11.43 cm X 3.81 cm laid over 87.50 mm mud filling on a layer of 25 mm mud plaster and an other layer of mud mortar for laying the tiles, including two coats of bitumen laid hot at 1.65 kg per sqm on top of R.C.C slab including grouting with cement sand mortar 1:3 and top surface to be left clean etc. (HSR 13.13+note) (i) first floor

Providing and fixing cast iron rain water non pressure pipe, I.S.I. mark with ears with screw and wooden plugs fixed on wall face including filling joints with spun-yarn and cement mortar 1:2 excluding head and shoe, etc. {HSR 13.45(a)} (a) 100 mm dia pipe

Extra over rate of item nos. 13.43 and 13.45(a) in case lead joints are used instead of cement joints {HSR 13.46(a)} (a) 100 mm interna dia

Providing and fixing C.I. plain bends in position with gutter, etc. {HSR 13.49(a)} (a) for 100 mm dia pipe

Top khurra 0.6 m X 0.6 m for rain water pipe in 25 mm thick cement concrete 1:2:4 over 50 mm thick cement concrete 1:8:16 (HSR 13.50(a)}

Bottom khurra on ground 1.2 m X 0.6 m consisting of brick-on-edge laid in cement mortar 1:3 over 75 mm cement concrete 1:8:16 including 12 mm thick cement plaster 1:3 (HSR 13.57)

Cement concrete 1:2:4 gola 10 cm X 10 cm quadrant along junction of roof with parapet wall finished smooth, where specially specified (HSR 13.64)

Providing and fixing false ceiling with 12 mm thick Gypsum Board fixed on M.S. steel runners frame including cost of screws angles, cleats, rawel plugs with taping, filling with Gypsum compound and applying priming coat etc. complete in all respects (HSR 13.91)

Providing and fixing mineral fibre false ceilings tiles at all hieghts of size 595 x 595 mm of approved texture, design and pattern, the tiles should have Humidity Resistance (RH) of 99%, Light Reflectance 85%, Thermal Conductivity K = 0.052 (-) 0.057 w/m k, Fire Performance as per (BS 476 pt - 6 & 7) in true horizontal level suspended on interlocking T-Grid of hot dipped all round gavanized iron section of 0.33 mm thick (galvanized @ 120 gsm) comprising of main T runners of 15 x 35 mm of length 3000 mm, cross T of size 600 x 600 mm suspended from celing using galvazied mild steel item (galvanizedd @ 80 gsm) 50 mm long 8 mm outerdiameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85 x 25 x 2 mm, spaced at 1200 mm centre of centre along main 'T'. The suystem should rest on periphery walls/partitions with the heop of GI perimeter wall angle of wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all hieghts, The work shall be carried out as per specifications, drawings and as per directions of the Engineer-in-charge. with or without groves (HSR 13.92)

Screed of 50 mm thick cement concrete 1:8:16 to be laid below the topping (HSR 14.4) (i) first floor

Kotah stone flooring, minimum 25 mm thick, in any pattern as specified over 20 mm thick base of cement coarse sand mortar 1:3 laid and jointed with neat cement slurry mixed with pigment to match the shade of stone including rubbing and polishing. (HSR 14.62+Note) (Note: The floor shall be finished with granite polish and nothing shall be paid extra). (i) first floor

Kotah stone 20 mm thick in skirting risers of steps, dados pillars and wall facing(lining) in any pattern as specified 12 mm thick cement coarse sand plaster 1:3 laid and jointed with neat cement slurry, mixed with pigment to match the shade of stone including rubbing and polishing including labour for fixing cramps, dowels and pins etc. (HSR 14.66 + Note) (i) first floor (Note: The skirting shall be finished with granite polish and nothing shall be paid extra).

Providing and fixing vitrified tiles of size 600 x 600 mm of approved make in flooring laid in any patterns as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles {HSR 14.89} Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSONS, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this.

Providing and fixing vitrified tiles of size 600 x 600 mm of approved make in skirting / dado laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade to tiles {HSR 14.90} Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSONS, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this.

Providing and fixing ceramic tiles/ anti skid tiles of size 400 mm x 400 mm or above size of approved make in flooring, laid in any pattern as specified over base of 20 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade of tiles Notes: i. Tile shall be premium quality (first quality) of reputed manufacturer like NITCO, KAJARIA, SOMANI, ORIENT BELL, JOHNSONS, RAK & SIMPOLO. ii. Tiles shall be fixed by using PVC spacers of required size and the space between tiles shall be filled up with cement based grout of approved make & colour. Nothing extra shall be paid for this. {HSR 14.91)

Providing and fixing 1st quality ceramic glazed wall tiles confirming to I.S. 15622 (thickness to be specified by the manufacturer) of approved make in all colour, shades except burgundy, bottle green, black of any size of approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement coarse sand mortar 1:3 and jointed with grey cement slurry, including pointing in white cement mixed with pigment of matching shades complete (HSR 14.92} (b) size of ceramic glazed tiles 300 mm x 450 mm

12 mm thick cement plaster 1:6 on walls (HSR 15.7+note)

15 mm thick cement plaster 1:6 on the rough side of single or half brick wall (HSR 15.12+note)

10 mm thick cement plaster 1:4 on underside of ceiling (HSR 15.52+note)

Striking joints in lime or cement on brick and tile walls {HSR 15.69(a)}

Cement pointing 1:2 flush on flat brick flooring (HSR 15.71)

Preparation of ply wood surface for painting including sand papering the surface and applying filling with approved quality filler consisting of white lead , linseed oil, varnish and chalk mitti including finishing the surface to required finish complete (HSR 16.1)

Applying pink primer or aluminium priming coat on wood work including preparation of surface, knotting and stopping, etc. (HSR 16.2)

Painting two coats excluding priming coat with synthetic enamel paint in all shades on new wood work or metallic or plastered or concrete surfaces to give an even shade (HSR 16.3)

Applying priming coat with metal primer on new steel or iron work including preparation of surface (HSR 16.9)

Applying priming coat with cement primer in all shades on newly plastered or concrete exterior surfaces (HSR 16.25)

White washing three coats (HSR 16.48)

Preparation of plastered surfaces for oil bound distemper including sand papering the surface, applying one coat of linseed oil, and filling with approved quality filler, consisting of white lead, linseed oil, varnish and chalk mitti including finishing the surface to the required finish complete (HSR16.52)

Distempering with washable oil bound distemper (of approved manufacture) two coasts excluding priming coat on new work (HSR 16.57)

Providing two coats of exterior acrylic emulsion paint (HSR 16.79) (b) 1st quality

Providing and applying two coats of white cement based putty over plastered surface and grinding the surface smooth with sand paper to get an even and smooth finish including cost and carriage of all material, labour charges, scaffolding, sundries etc., complete (J.K/ Birla make). (HSR 16.81)

Proving and fixing 35 mm thick glazed door and windows shutters of commercial hard wood such as hollock, champ, chikrassy and chaplash, etc. ( non-coniferous timber other than teak confirming to I.S. specifications No. 1003 kiln seasoned), with vertical styles and rails, as specified in the statement no.1 ( attached in the end of this chapter), with glass panes of 4 mm thickness , tongued and grooved including the cost of iron hinges , screws, chocks/cleats, stops , etc., complete fixed in position excluding the cost of tower bolt and handles but including the labour for fixing the same (Based on 17.30 (a) + 17.24 (c)} (b) 35 mm thick ( 4 mm thick glass panes)

Providing and fixing sliding bolt with nuts and screws, etc., complete (HSR 17.83(b)(ii)} (b) aluminium (ii) size 250 mm X 16 mm

Factory manufactured solid flush door shutters, with block board core as per I.S. No. 1659-1969 bonded with water proof type phenol formaldehyde synthetic resin, hot-pressed, conforming to I.S. 2202 part I and II, fixed in position, including iron hinges, screws, chocks/cleats and stops, etc., (excluding the cost of any fittings other than specified above, but including labour for fixing the same in position)- (a) commercial veneering with vertical grains or cross bands and face veneer on both sides commercial facing with laminated core and lipped edges :- {HSR 17.93(a)} (iii) 35 mm thick

Providing and fixing Aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS;733 and IS; 1285 fixed with raw plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. aluminium sections shall be smooth rust free straight mitered and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling C.P. brass/ stainless steel screws, all complete. (HSR 17.95) Fixed portion (Anodized Aluminium transparent or dyed to required shade according to IS;1868, minimum anodic coating of grade AC 15)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS; 733 and IS;1285 fixed with rawl plugs and screws or with fixing clips or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom, and sides with required neoprene felt etc. Aluminium sections shall be smooth, rust free straight mitered and jointed mechanically wherever required including clear angle, Aluminium snap beading for glazing/ paneling C.P. brass/ stainless steel screws, etc. complete. (HSR 17.96) Shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including of cost of PVC/ neoprene gasket required including Aluminium fitting.(powder coated)

Providing and fixing glazing in aluminium door, windows, ventilator shutter and partitions etc. with PVC/ neoprene gasket etc. complete (cost of aluminium snap beading shall be paid in basic items). {HSR 17.98(b)} (b) With float glass panes of 5.00 mm thickness.

Wrought iron and mild steel (using angles, flats square bars. tees and channels) ladders, grills, gratting frames, window guards, iron door openable or fixed stair case or parapet or any other type of railing , gates and tree guards etc., including cost of screws and welding rods or bolts and nuts complete fixed in position (HSR 18.12)

Steel reinforcement TMT bars FE-500 EQR/FE-500 D grade or more for RCC work, where no included in the complete rate of RCC incluidng straightening, bending, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. and placing in position, complete in all respect for all heights/depths/storeys/basements etc. Note: Reinforcement shall be measured in length including hooks, if any, separtely for different diameters as actually used in work excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods for binding and placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. (HSR 18.22)

Supplying and fixing glass panes including special metal sash putty of approved make(HSR 18.30(b)} (b) glass panes 4 mm thick, exceeding 40 sq dm areas

Pressed steel sheet frames (chowkhats), consisting of 2.00 mm thick steel sheet of the specified section, including iron lugs (hold fasts, iron hinges, confirming to PWD specifications, including bolts for fixing stops, locknotch, provision for receiving tower bolts, and finished with one coat of ready mixed paint red led non-setting primer of approved quality, fixed in position including the cost of cement concrete 1:3:6 for filling in the frame, and cement concrete 1:3:6 for lugs, complete:- {HSR 18.34(a)} (a.) door and window frame of size 89mmx 50mm with 40mm wide single rebate.

c. door and window frame of size 127mmx 50mm with 40mm wide double rebate..

Providing and fixing marble strips of size 14 mm to 17 mm thick and 40 mm wide in cement concrete/ terrazzo flooring fixed in position, complete in all respects as per drawing and design or as directed by Engineer-in-Charge. (NS)

Providing and fixing C.I. grating over 100 mm dia rain water pipe, fixed in position, complete in all respects.(NS)

Providing and fixing stair case railing consisting of 50 mm X 20 mm M.S. tube (12 gauge) as hand rail and 20 mm X 20 mm M.S. square pipe (12 gauge) as balusters including holdfast making hole in kotah stone and filling the same with lead cutting, welding, priming coat and painting, etc., fixed in position, complete in all respects as per drawing and design.(NS)

Providing and fixing wall paneling (on wall) consisting of following:- Frame work:- (NS) Consisting of factory manufactured G.I. channel of size 43 mm x 15 cm x 0.8 mm fixed horizontally @ 2’-0” C/C with rawl plugs/ screws on wall. (a) 9 mm thick commercial plywood (ISI mark) of approved make fixed on G.I. channel frame. (b) Top portion:- Consisting of 0’-6” wide strips of 1 mm thick plastic laminated sheet (ISI mark) of approved make, shade and colour with 1/8’ groove fixed on plywood. (c) Beading:- Beading of size 0’-2¼” x 0’-1¾” of commercial hard wood such as hollock, champs, chikrasy and chaplash at top. Including cost of sprit polishing, rawl plugs, nails, screws etc., complete in all respects as per architectural drawing and design

Providing and fixing aluminium grills made of square bar/round bar/ or any other section of Jindal or any other equivalent make on window. Complete as per specification & directed by engineer-in-charge (NS)

Manufacturing and supplying conference table of elliptical shape having 2'-0" width and 2'-6" height consisting of following:-(N.S.) (a) FRAME WORK:- Consisting of 25 mm x 25 mm M.S. tube (12 gauge) as per architectural drawing. (b) TOP PORTION (2’-0” WIDE):- Consisting of 25 mm thick commercial type block board (ISI mark) of approved make finished with 1 mm thick plastic laminated sheet (ISI mark) of approved make, shade and colour. (c) PANELLING/VERTICAL PORTION (for inner surface):- 1’-11½” high wooden paneling consisting of 0’-4" wide and 0’- ¾" thick strips of teak wood having3/8" wide groove over 6 mm thick commercial plywood fixed on teak wood battens of size 25 mm x 25 mm & steel frame and 4 mm thick commercial plywood on back side to cover frame. (d) MS angle iron of size 25 mm x 25 mm x 5 mm welded with MS tube legs to fix the wooden strips (one at top and one at bottom). (e) Beading:- Teak wood beading of size 0'-¾" 0'-1" at upper edge and 0'-2½" x 0'-1 1/4" (5/4") at bottom of top surface of required shape on both edges of table (outer and inner edges). Including cutting, welding, primer and painting on MS tube frame work , spirit polishing, nails, screws, nuts & bolts, fevicol, brass adjustor etc., complete in all respects as per drawing and design.

PH work items 66 to 133 Cement conc. 1:2:4 with stone aggregate 20 mm nominal size for reinforced conc. Work in slabs with inclination not exceeding 25 degree with horizontal, excluding steel reinforcement, but including centering and shuttering, laid in position, complete in all respects. (HSR 10.82)

Extra over item Nos.10.79 to 10.94, if 1:1½:3 mix is used instead of 1:2:4. {HSR 10.95(a)}

First class brick work laid in cement sand mortar 1:5 in first storey up to 4 metres above plinth level.(HSR 11.8)

12 mm thick cement plaster 1:6 on walls (HSR 15.7)

Steel work, fixed independently without connecting plates, including cutting, hoisting and fixing in position in :- {HSR 18.1} (a) R.S. joints 6"x3"

Fe-500 D TMT steel bars for R.C.C., works, where not included in the complete rate of R.C.C. , including bending ,binding and placing in position complete (HSR 18.22)

Labour for laying, jointing, fixing and testing G.I./P.V.C./W.I. pipe lines and specials tees, bends, sockets elbows etc. inside building and testing etc. complete including cutting threading. {HSR 28.18(b)} INCLUDING COST OF SPECIALS (i) 15 mm internal diameter of pipe line

(ii) 20 mm internal diameter of pipe line

(iii) 25 mm internal diameter of pipe line

Extra for fixing and jointing union couplings in G.I and W.I pipe lines. {HSR 28.21} (a) 15 mm internal diameter

(b) 20 mm internal diameter

(c) 25 mm internal diameter

Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required. (HSR 28.24) (a) 11.43 cm thickness of walls

(b) 22.86 cm thickness of walls

Cutting holes up to 23 cm square for pipes in floor and roofs of cement concrete reinforced concrete or reinforced brick work and making good including repointing, replastering, replacing bitumen and colour or white washing where required. {HSR 28.26(b)} (b) 115 mm thickness of roof of floor

Fixing and jointing gun metal peet valves (heavy pattern) with hand wheels, on G.I pipelines laid in the ground or inside buildings including cartage from divisional stores or nearest railway station to site of works. {HSR 28.29} (b) 15 mm internal diameter

(c) 20 mm internal diameter

(e) 25 mm internal diameter

Providing and fixing in position best Indian make (to the approval of the Engineer-in-charge). Indian type Orissa or orya water closet suite for sinking into floor, with raised foot treads complete with 100 mm H.C.I ‘P’ trap with or without vent as required and all other necessary fittings as fully described in item no. 30.1 above (without cost of C.I. high level flushing cisterns) (based on 30.2(a)(i)} (a) 580 mm (i) WHITE

Providing and fixing in position best Indian make European type water closet suite with concealed ‘P’ of ‘S’ trap with or without vent (as approved by the Engineer-in-Charge) and all other necessary fittings as fully described in item No. 30.3 above (without cost of C.I. high level flushing cisterns) {based on HSR 30.6(i)} (White)

Extra over item no. 30.3 to 30.6 for providing and fixing best Indian make plastic hygenic seat with lid complete instead of hollow black or white plastic seat and lid. {HSR 30.13(i) (i) White plastic seat ( Solid)

Extra for providing and fixing 32 mm dia. G.I/ C.P flush pipe complete with accessories instead of 32 mm dia. Galvanised telescopic flush pipe with clips ( as required by the Engineer-in-charge) {HSR 30.15(b)} (b) 32mm dia C.P brass flush pipe

Providing and fixing in position best Indian make a range of two urinals large flat back or angular lipped front 610 mm high in vitreous china-ware with 5 lit capacity best Indian make C.I automatic flushing cistern with fittings and flush pipe etc. complete as fully described in item no. 30.25 above, {HSR 30.26(i)} Range of two urinals (i) White

Extra for providing and fixing vitreous automatic flushing Cistern including fittings and brackets of C.I. flushing cistern complete {HSR 30.37(b)(i)} 10 ltr. capacity cistern (i) White

Extra for providing and fixing standard size C.P. brass flush pipe complete with fittings instead of G.I flush pipe complete {HSR 30.38) (ii) For a range of two urinals

Providing and fixing 25 mm thick marble partitions for different type of urinals. {HSR 30.40(b)(II)(i)} (b) Vitreous Chainaware Partition Plate (II) LARGE SIZE 835 mm x 355 mm (i) White

Providing and fixing in position best Indian make (ordinary) lavatory suites consisting of Lavatory in vitreous china ware size as given below (to the approval of the Engineer-in-charge) including china plug for tap hole where necessary, R.S or C.I brackets for building into wall including painting;32 mm C.P. brass waste with C.P brass chain and rubber plug;15 mm C.P brass screw down pillar tap with jamnuts or couplings best design ( as approved by the Engineer-in-charge) all fittings best Indian make and; to the approval of the Engineer-in-chargeall brass work chromium plated and complete in all respects including cutting and making good the walls and floors and painting of fittings etc. (HSR 30.41) (iv) size 550 mm x400 mm with one no tap

Providing and fixing in position 32 mm dia G.I waste pipe embedded in wall or lead waste pipe (weighing 3.47 kg per meter and 2.8 mm thick) up to floor level including cost of wipped solder joint etc., complete (as required by the Engineer-in-charge) {HSR 30.48}

Providing and fixing in position best Indian make chromium plated brass bottle trap 32 mm diameter {HSR 30.50}

Providing and fixing in position best Indian make soap dish fixed into wall with C.P brass screws and complete in all respects including cutting and making good the walls etc. {HSR 30.70(a)(ii)} (a) C.P. BRASS (ii) soap dish small

Providing and fixing in position best Indian make bevelled edge 5.5 mm thick mirror mounted on asbestos sheet ground fixed in position by means of 4 nos. chromium plated brass screws and washers over rubber washers and rawl plug embedded in the wall of chromium plated brass clamps with C.P brass screws ( as required by the Engineer-in-charge) complete including cutting and making good the walls etc.{HSR 30.71(a)(i)} (a) INDIAN MAKE (i) 600mmx450mm

Providing and fixing in position 15 mm i/d C.P brass bib cocks of best quality ( as required by the Engineer-in-charge) {HSR 30.75(a)} (c) Bib cock

Providing and fixing in position C.P brass stop cock (as approved by the Engineer-in-charge) {HSR 30.76 (a)} a) 15 mm stop cock (ii) concealed stop cock with flange

Providing and fixing in position best Indian make C.P brass inlet connection 15mm with 375mm pipe and C.P brass nuts. (HSR 30.83)

Providing and fixing in position H.C.I soil waste vent or antisyphonage pipes to I.S.I specifications of E.L.C manufacture or of any other reputed firm including cutting and wastage etc. and cutting holes in walls, roofs or floors etc. and making good to its original condition but excluding cost of lead jointing. {HSR 30.84 (a & b)} (a) 100 mm internal diameter

(b) 75 mm internal diameter

Providing lead caulked joints to H.C.I pipes and specials conforming to I.S.I specification of E.L.C manufacture or any other reputed firm including cost of lead yarn, fuel and tools etc. {HSR 30.87(a &b)} (a) 100 mm internal diameter

(b) 75 mm internal diameter

Providing and fixing in position M.S. or heavy flat iron clamps made out of M.S flat not less than 5mm of the approved design for fixing C.I soil waste vent or anti pipes to walls complete in all respects including cutting and making good the walls and floors etc. and painting {HSR 30.88(a &b)} (a) for 100mm internal diameter pipes

(b) for 75mm internal diameter pipes

Providing and fixing H.C.I. floor traps I.S.I. marked of the self cleaning design with C.P. brass hinged grating with frame with or without vent arm and including cement concrete 1:2:4 under the around the floor trap where required upto floor level complete in all respects including cutting and making good the walls and floors, etc., minimum depth of water should be 150 mm with a minimum seal of 50 mm {HSR 30.89(b)} (b) With 75 mm internal dia outlet

Providing and fixing in position H.C.I specials for soil, waste, vent or anti-syphonage pipes to I.S.I marked including cutting and wastage etc/., and making good to its original condition but excluding cost of lead jointing. {HSR 30.91} (a) For 100 Mm I/D Pipes (i) heal rest bend

(iv) single junction with door 100mmx100mmx100mm

(xiii)bend with door

(xiv) bend plain

(xvi) cowls

(xxii) collars

(b) For 75 Mm I/D Pipes (i) heal rest bend

(iv) single junction with door 75mmx75mmx75mm

(xiii) Bend with door

(xiv) Plain bend

xvii) Cowls

(xviii) Collars

Cutting chase in brick walls in cement or in floor for embedding G.I. or H.C.I. pipe lines and making good the same to its original condition {HSR 30.95(a) (a)size 75 mm X 75 mm

Providing and fixing in position automatic brass ball valves in tanks {HSR 30.110(b)(iii)} (b) WITH PLASTIC BALL (iii) 25 mm internal diameter

Providing and fixing in position gully traps fixed in cement concrete 1:4:8 complete with H.C.I. grating 150 mm X 150 mm cast iron cover weighing approximately 7.26 kg. and frame clear opening 300 mm X 300 mm and outside size 330 mm X 330 mm and chamber including cost of all brick work in cement mortar 1:5 cement concrete 1:8:16 in foundations, and cement concrete 1:2:4 in coping around C.I. cover and frame et. With three coats of black bitumastic superior paint of approved manufacture on all C.I. work as per standard design, minimum depth of water should be 150 mm with a minimum seal 50 mm {HSR 30.114(b)} (b) 100 mm internal diameter H.C.I. gully trap

Providing and fixing HDPE WATER STORGE TANKS of sintex, diplas O.K. Supreme make with covers/ lids marked with IS: 12701 on roof top of buildings including cost of hoisting and placing in position, making connections with inlet and outlet pipes, providing overflow & scour provisions with suitable plug on scour pipe including cost of nipples, washers, flanges for connections in tanks complete in all respects to the satisfaction of Engineer-in- Charge. {HSR 30.119) 1000 ltr,. capacity

Supply of G.I. pipe ‘B’ class ISI marked of ‘Ravindra’/ ‘Jindal’/ ‘Parkash ( Surya)’/BST make {NS) (a) 15 mm internal dia

(b) 20 mm internal dia

(c) 25 mm internal dia

Supply of G.I. Union couplings of Unik / Unco make {NS} (a) 15 mm internal dia

(b) 20 mm internal dia

(c) 25 mm internal dia

Supply of G.M. Peet valve (heavy type) of DRP/Leader/Bajaj make ISI marked. {NS} (b) 15 mm internal dia

(c) 20 mm internal dia

(d) 25 mm internal dia

Providing and fixing CP brass jet along with flexible pipe 15mm i/d and patti etc. of best quality complete in all respects (excluding cost of CP brass concealed stop cock).(NS)

Providing and fixing in position PVC flushing cistern 8.0 ltrs. capacity of Hindware/Cera/perryware make ISI marked, white, alongwith fittings complete in all respect. (NS)

Electrical work items 134 to 170 MINIATURE CIRCUIT BREAKER AND ISOLATOR:(HSR 31.17) Supply and erection of miniature circuit breaker/isolator 240/415 V in the existing distribution board including making necessary connections (a) Miniature Circuit Breakers of 9 K.A. breaking capacity (ii)6-32 amp. SP MCB

(ii) 32 amp. SPN MCB

Supply & erection of fittings & accessories: (HSR 31.18) (xxvi) S/E of hexagonal M.S. box 1.60mm thick having each side 8 cms., 7.5cms deep, top covered with M.S.lid by means of screws including 10 mm dia 30cm long mild steel rod made into suitable suspension hook and erected in RCC slab.for erection of fan, the bottom covered with 3mm thick bakelite sheet with suitable holes, painting etc. complete with all labour and material required to complete the job.

PIPE LAYING: Supply and erection of pipe for wiring purposes including bends inspection boxes etc. where necessary and painting as required :-(HSR 31.21) (xxii) Heavy gauge welded conduit pipe 25 mm dia 1.60 mm thickness on flushed.

EARTHING (HSR 31.22) (i) Earthing with G.I. earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the top etc. as required

(ii) Extra for using salt and charcoal/coke for pipe earth electrode as required.

(xii) Pdg. and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in 15mm dia G.I. pipe from earth electrode as required.

(xvi) Pdg. & fixing 4mm dia GI wire on surface or in recess for loop earthing as required.

UNDERGROUND CABLES (HSR 31.25) S/E of underground cable 1 metre below ground level covered with sand and bricks including necessary connections, digging and refilling of trenches. (xxix) 3½ x 95 sqmm(armoured)

(xliii) 4 x 50 sqmm(armoured)

S/E of suitable compression type brass cable glands for underground cable (HSR 31.28) (iii)25 sqmm to 50 sqmm cable 2 to 4 core.

(iv) 70 sqmm to 95 sqmm cable 3 to 3½ core.

Miscellaneous (HSR 31.35) (i) Supply of M.S. Pipe (B-Class) for suspension rod of ceiling fan including threading if required. (a) 15mm dia

S/E of PVC unsheathed copper conductor cable single core 1100 volt grade in pipe of suitable size excluding cost and erection of pipe (HSR 31.40) (i) Size 1.5 sqmm(3/0.81mm)

(iii) Size 4 sqmm(7/0.85mm)

(iv) Size 6 sqmm(7/1.05mm)

(v) Size 10 sqmm(7/1.35mm)

S/E of PVC conduit pipe ISI marked (Medium) recessed in wall/ceiling etc. including cost of PVC bends, inspection box and all other material required to complete the job in all respect up to the entire satisfaction of Engineer-in-Charge of work (HSR 31.44) 25mm dia

Pdg. and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect. (HSR 31.56) 10 amp. 1 way switch

20 amp. Switch

10 amp. socket

16 amp. socket

Fan regulator

Blinking plate

Pdg. and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. (HSR 31.57) 1 & 2 Modules

6 Modules

12 Modules

Suppluy and erection of module case circuit breaker single pole/4 pole on wall on existing prdestal including boundaing to earth and making necessary connection required to complete the job in all respect up to the entire satisfaction oof the Engineer-in-charge of work (HSR 31.69) (iv) 4 pole MCCB 6-63 amp

(vi) 4 pole MCCB 200 amp

Supply & laying of multicore telephone cable conductor size 0.51mm bright annealed copper cond. PVC insulated and sealed in existing pipe/ channel etc (i) 2 Pair telephone wire (HSR 31.78)

S/E/T/C of cat-6 cable in existing PVc conduit /PVc channel complete in all respect with all labour and material required to complete the job in all respect. (HSR 31.80)

S/E of Internet Jack RJ-45 Modular complete in all respect Make: D-Link (NS)

S/E of I/O Box for internet connection includng I/O box, face plate and internet jack, Make Delink (NS)

S/E of AC ceiling fan capacitor type complete with shackle, 300mm down rod and regulator etc. {NS} i) 1400mm sweep. Make: Usha, Orient, Crompton.

S/E of surface/wall mounted ≤20W integrated LED 4 feet fitting with Epoxy Powder coated white/Grey extruded aluminium channel housing for efficient heat dissipation. Total system lumen of 20 watt LED should be ≥ 2000 or above in cool day light (5700K to 6500K), Power factor >0.95, CRI >80, Average life >50000 hours. Complete with mounting Brackets & accessories as required with connections(Industrial) Make: Philips, Havells, Wipro, Bajaj. (NS)

S/E of recessed type ≤ 42 Watt full window glare free opal diffuse LED Panel of size 595x595 mm suitable for Armstrong/POP/GB ceiling with M.S. Powder coated white housing. Total system lumen of 42 watt LED should be ≥ 4600 or above in cool day light (5600K to 6500K), Power factor >0.95, CRI (Ra) >80, LED lamp Make- Cree, Nichia, Philops Lumiled Osram, Edison, LED Lamp efficacy > 130/m/w, Average life > 50000 hours, complete with all accessories as required with connections(Industrial) Make: Philips, Havells or Wipro, Bajaj. (NS)

S/I/T/C of push ON/OFF type 25 A modular type motor starter switch (white color) for AC's including the cost of petty material required to compete the job upto entire satisfaction of Engineer-in-charge. (NS) Make;- Schneider/Crabtree/Athena

JAGAT SINGH CONTRACTOR