SPECIAL REPAIR TO BLDG NO 100 ORs MD ACCN (TOTAL QUARTERS 08) AT (KALIDHAR LINE) 14 GTC SUBATHU UNDER GE KASAULI

Amount

Schedule 'A' Section - I

Demolition of cement concrete (un re-inforced) in ground floor and paving n.exc. 15 cm thick below or above ground level complete all as specified .

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition)

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

Dismantling PVC 75/110 mm drain or vent pipe of any description in any position including bends branch pieces etc.

Dismentling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillet complete all as specified and as directed .

Taking down cement plaster on brick wall surfaces etc incl raking out joints hacking for key, scrubing down with water etc cpmplete all as specified and as directed

Dismantling floor, hearth or wall tiling incl cement mortar bedding (but not backing) and rubbish off the premises complete all as specified.

Demolition of stone slabs and tiles of any description or thickness in floors aprons etc laid bedded and pointed in any mortar.

Demolition of brick work or stone boulder masonry built in cement mortar complete all as spd and as directed.

Taking down chowkhats or frame with shutter (without taking off shutters from the frames) n.exc. 1.5 Sqm complete all as spd and as directed.

Taking down chowkats or frames with shutters (without taking off shutters) exceeding 1.5sq.m and not exc 4.00sq.m each of any description incl making good the disturbed surfaces complete all as specified & directed..

Dismantling plain or corrugated steel sheeting any guage thickness incl Nainital pattern as in roof covering complete all as specified.

Material & Labour brick work with sub class 'B' bricks of class designation 10 all as per IS-1077-1992 (minimum compressive strength of brick 100 kg/Sqcm) old size bricks, straight or curved on plan exceeding 6 mtr mean radius built in CM 1:6, complete all as specified & directed.

Material & labour for 15mm thick rendering in cement mortar 1:4 over fair faces of brick masonry surfaces or concrete surfaces finished even and smooth without using extra cement complete all as specified.

M&L rendeing 10mm thick other then fair faces surfaces in CM 1:6 finished even and smooth with out using extra cement (Internal surfaces)

M&L rendering 5mm thick in CM (1:3) on fair faces of concrete surfaces as in ceilling finished fair and even without using extra cement complete all as specified and as directed

Material & Labour for Plain Cement concrete type B-1 (1:2:4) using 20mm graded crushed stone aggregate as in seismic and other similar bands, shelves, copings, bed plates, hold fasts, plinth courses, filling in pressed steel frame and the like finished fair and even incl necessary form work complete all as specified & directed.

Material & Labour for 50mm thick plain cement concrete C-1, 1:3:6 (using 20mm graded crushed stone aggregate) as in plinth protection finished fair and even without using extra cement complete all as spd & directed. Note:- The plinth protection shall be laid in pannels and length of the each panel shall not be more than 2.00 mtr all as directed. 6mm joints filled with 85/25 grade bitumen and sand (1:3 ratio) shall be provided. No deduction for joints shall be made while making payment against the above item.

M & L RCC 1:2:4 type B-1 using 20mm graded stone aggregate as in shelves / slabs and like with and incl use and waste of necessary form work complete all as specified.

PCC (1:3:6) type C2 using 40mm graded agg as in surface channel / drains.

Extra for forming fair finished drain or channel 30 cm inner girth in forms, moulds/stopped ends etc.

M & L MS TMT Bars 10mm dia and over cut to length, bend to shape required, incl cranking, bending, for hooping for columns, hooking ends and binding with and incl MS wire (Annealed) not less than 0.9mm dia or securing with clips complete all as specified.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges etc. fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm as directed by Engr-in-Charge at site with suitable arangement as required complete all as specified & directed.

Supply and fixing Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges, flashing, eaves board valley gutter of any shape etc, cut to designed shape (Jhhallar) as directed at site fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm as directed by Engr-in-Charge at site with suitable arangement as required complete all as specified & directed.

S&F aluminium flat sections as in wind tie complete all as specified and directed by Engr- In-Charge.

M & L Non Skid ceramic tiles 7 to 8 mm thick area exc 0.18sqm n exec 0.38 sqm in floors, set and jointed in neat cement slurry and pointed in white or colored cement to match with the tiles incl. 15mm thick screed bed or bedding layer in C.M 1:4 etc complete all as specified & as directed

M&L for first quality joint free Non Skid glazed ceramic tiles (coloured) area exc 0.11sqm but n exec 0.18 sqm (square/rectangular) as in floors set and jointed in cement slurry and pointed in coloured cement including provision of screed bed 15mm thick in CM (1:4) complete all as spd & as directed.

M&L for coloured glazed ceramic tiles in vertical surface 350 x 250 x 7mm / 450 x 350 x 7mm /450X300X7 mm thick set & jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm screed bed in 1:6 cement mortar complete all as specified & as directed.

S&F in repair Material and labour for false ceiling with one layer of 'LaGyp' standard boards manufactures by M/S Lafarge Board Gypsum India Pvt Ltd, at all height and levels. Standard boards of size 1220x1830x12.5mm, standard board to be laid on 'LaGyp' universal channel (web 45 mm premanunfacturers specifications metal comprising of "LaGyp" universal channel (web 45 mm and flange 27mm base metal thickness (BMT) 0.55 mm and length 3660 mm to be used as main channel as well as ceiling channel. "LaGyp" connecting clips, perimeter channel ( Size of web 28 mm, flange 18/30 mm and length 3660 mm, MBT 0.55 mm) and "L" angle (Lenght 3050 mm BMT 0.55 mm) with finally the board are to be Jinded and finished so as to have a flush look with which includes filling and finishing the tepered and square edges of the board with "LaGyp" easy joint Gypsum based jointing compound, "LaGyp" paper tape. The rate should include providing and laying two or more coats of oil bound distemper to give a neat and even finish including preparing the base with primor and scaffolding etc complete in all respect complete all as specified and as directed by Engr-In-Charge .

Pressed steel frames for doors of size 105 x 60mm thickness 1.25 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, as specified, supplied and fixed.

Pressed steel frames for doors of size 125 x 60mm thickness 1.25mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete, as specified, supplied and fixed.

S&F factory made steel windows with side hung shutters including projecting type hinges with steel handle , and steel peg stay , complete with glazing bars , dovetailed or welded complete all as specified & directed

-do- but steel window , fixed type, with glazing bars -do- Note for item No. 32.00 & 33.00 : Glass required for fixing in window and ventilator will be measured and paid for separately under respective item of this schedule. However the quoted rate deemed to include for necessary fixing of glass.

S&F steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and / or riveted, or forged into spikes , framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings , framework of water tanks and similar work conforming to Fe 290 Gde E-165.

S&F galvanised mild steel wire cloth, 0.63mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples complete all as specified.

S&F sheet glass , ordinary quality & glazing 3mm thick, with oil putty in square n. Exc 0.5 Sqm in each pane complete all as specified & as directed.

S&F figured glass 4mm thick, pin head type and glazing with oil putty in square n. Exc 0.5 Sqm in each pane complete all as specified & as directed.

Supply and fixing Factory made plain, framed, panelled shutters , 35mm thick of 2nd class hard wood (Hollock) with lock rail and panels of 9mm thick commercial ply or 12mm thick vaneered particle board with commercial veneered on both sides, incl priming coat, duly hammer marked. The size of rail & style shall be as per IS 1003 part-1 kiln seasoned and chemically pressure treated incl one coat of pink primer complete all as specified & directed.

M&L 30mm thick 2nd class hard wood glazed and skeleton shutter factory made open revated and prepared to receive glass, guage etc with plain chamfered or rounder mitred and rebated, sash bars in any numers divided into squares edges of framing, plain or chamfered or rounded as specified in SSR Pt-I, section 8, clause 8.24(a) supplied and fitted to chowkats complete all as directed by EIC.

Mild Steel works as in bends straps, hold fasts etc, conforming to IS-2062 (Fe-290), embedded portion duly painted with bituminious paint and sanded, complete all as specified.

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5mm wood grain printed PVC sheet reinforced with mS square tube etc complete all specified.

S&F factory made solid PVC moulded door shutter 28 to 30 mm thick (stiles) with 2.4 (or) 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet polyurethen painted on the front face and 2mm plain colur PVC sheet on back face with particle board core etc complete all specified & as directed .

S & F in repairs curtain rails anodised aluminium alloy with fixing brackets etc complete all as specified

Supply and fixing 2nd class hard wood small fittings such as brackets of any type latch and hinges blocks shaped door and windows stops and the like, including all necessary labour, articles n.exc. 200 cucm each complete all as specified & directed.

Supply and fixing Mild steel butt hinges medium weight , clod rolled, 100mm, ISI marked, complete all as specified & directed.

Supply and fixing Mild steel butt hinges medium weight , clod rolled, 50mm, ISI marked, complete all as specified & directed.

Material & Labour barrel tower bolts aluminium anodised extruded section of size 200 mm complete all as specified & directed.

Material & Labour barrel tower bolts aluminium anodised extruded section of size 150 mm complete all as specified & directed.

Supply and fixing aluminium fabricated type extruded handles of size 125 mm complete all as specified & directed.

Supply and fixing 300 mm long aluminium anodised sliding door bolt with hasp, staple (bolt type) and fixing cleap of sheet, cast or extruded sections, bolt not less then 12mm dia with and including a minimum of 6 bolt and nuts ,fixed on plate or staple plate complete all as specified & directed.

M&L for preparation of plastered or unplastered old decorated surfaces of walls incl pillasters and cornices etc. incl washing, rubbing down and stoping the connected previously treated surfaces and applying two coats of oil emulsion distemper (tint as approved by GE) complete all as specified & directed.

M&L for preparation of plastered or unplastered new surfaces of walls and applying two coat of oil emulsion distemper (tint as approved by GE) including one coat of primer complete all as specified.

M&L preparation of newly plastered or unplastered or previously untreated surfaces of walls and applying two coats of exterior emulsion/Apex paint complete all as specified.

Material & labour for preparation of old painted wood or wood based surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint (1st quality) complete all as specified & directed.

M & L Preparation of new or previously untreated surfaces of wood or based materials of any description not otherwise described, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M & L for preparing surfaces of steel and iron work, new or old , as in small articles such as hold fasts etc and treating with tar or coal tar black paint, area tarred not exc 0.10 sqm each.

Material & labour for preparation of new steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coat of synthetic enamel paint (1st quality) over a coat of red-oxide primer complete all as specified & directed.

M&L for preparation of plastered or unplastered old decorated surfaces with sand papering of walls incl cornices etc. incl washing, rubbing down and stoping the connected previously treated surfaces and applying one coat of acrylic emulsion exterior quality (Apex painting) (tint as approved by GE) complete all as specified. Note:- Paint and primer shall be 1st quality.

Taking up or down 15 mm dia steel tubing and connection and removal from site

- Ditto- but 20mm dia

S&F steel water tubing medium grade galvanized with all fittings and fixed complete to walls and ceiling or laid into floor or 15mm bore complete all as spd.

-ditto- but bore of pipe 20mm

Taking up or down steel tubing and connections cleaning for refixing and refixing oldsteel tubing and connections in new or in old position (walls cediling floor etc) of 20mm bore of pipe complete all as specifie

-do but 15mm bore

S & F in repairs 15mm bib tap cast copper aloy with crutch or butterfly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified.

Supply & fixing wash hand basin, vitreous china, white, decorative type, flat or angle back, size 550mm x 400mm incliding cutting for and pinning in ends of brackets or erecting stand including waste pipe , fixed as in repairs complete all as specified.

S & F in repair 15mm pillar tap cast copper aloy with capston heads chromium plated screwed down fly nuts screwed for iron pipe or for brass ferrule and fixed complete all as specified.

S & F in repairs brass chromium plated tubler towel rail 20mm dia D type 60cm long between flanges complete all as spd.

S&F in repair grating doom 100 mm dia of PTMT (Min wt 25g) all as specified and as directed

Dismantling water tanks n.exc 500 ltrs cap and removing to store complete all as spd.

S&F 500 ltr cap ratational moulded polythene water stoarage tanks ( clyndrical vertical with closed top) hoisted and fixed in position complete all as spd.

S & F in repair 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipes etc, complete all as specified

S&F in repairs of flushing cistern PVC 10 ltrs cap valve less syphonic action type, low level white with intel , ball valve , float incl brackets and PVC flush pipe 32mm dia complete all as specified. .

Supply and fixing angle stop valve, chromium plated, brass fancy type, screwed down, high pressure with crutch or butterfly handle screwed down , screwed for iron pipe or for union, suitable for 15mm bore pipe, fixed as in repair complete all as specified and directed.

Supply and fixing 15mm dia PVC connection with brass nut, of length 450mm, in repair complete all as specified and directed.

S & F in repairs vitreous china squatting pan, "Orissa Pattern" size 580 x 440mm white with integral foot rest (excluding flushing cistern) and flush pipe complete all as specified

S&F in repair stop valve cast copper alloy 20mm bore screwed down high pressure with crutch of butterfly handle scewed both ends for iton pipe or for unioin fixed complete all as specified

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required complete all as specified.

S&F 75mm dia PVC (SWR) bends with oval accesse door with rubber ring joints fixed as required complete all as specified.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvant cement incl necessary PCC & form work as required complete all as specified.

S&F 75mm dia PVC (SWR) junction single, (single T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) junction single, (single T), equal or un equal with oval accesse door including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 75mm dia PVC (SWR) branch piece, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 110mm dia PVC (SWR) reducer, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

S&F 75mm dia PVC (SWR) vent cowl, single, equal or un equal of any length including jointing with solvant cement as required complete all as specified.

M&L for Granite as in steps, pillars, window cills, cooking plateforms and like, 20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick cement screed bed in CM(1:6) complete all as specified. ( size of the slabs shalll not be less than 100cmx60cm ) Note:- (i) The rate of granite stone shall be deemed to incl for full rounded off corner/ edges incl all cutting to make it square or rectangular. (ii) The rate shall also be deemed to incl for cutting and polishing machine and granite polishing to achive the desired granite finish all as spfd.

S & F in repair soap dish chromium plated of size 180x160x90mm any type, fixed with chromium plated brass screws complete all as specified.

Material and labour for sink with drainage board made out of stainless steel sheet 1.0mm thick with plug, washers and wastes, overall size 915mm x 460mm, bowl size 410mm x 330mm x160mm incl fixing cantilever brackets and connection to union, pipe, fixed as in repairs complete all as specified and directed.

Supply & fixing stainless steel plate rack, made out of 1.00mm thick sheet of size 24"x36"x10" deep, ISI marked, fixed as in repairs complete all as specified and directed.

Supply & fixing pre-laminated particle board 19mm thick, interior grade pre laminated one side with decorative choice laminations and other side balancing white lamination, fixed with screws to timber / steel frame work as in shelves or shutters or wall panelling, fixed as in repairs complete all as specified and directed.

Material & labour piano hings, mild steel bright finish width of flap 40mm fixed in repair including taking out the existing complete all as specified and directed

Supply & fixing magnetic catches brass body for use in cup boards of kitchen, ward robes etc. fixed as in repairs complete all as specified and directed.

Supply & fixing 40mm dia cupboard knob of brass, polished, fixed with nut screw and washer, fixed as in repairs complete all as specified and directed.

S & F in repair chromium plated shower rose (125mm) with swivel joints fixed to steel pipe or union complete all as specified and directed.

Hasp and staple 75mm, mild steel, wire type, stove enamelled black, including bolt to hinge plate and fixed with screws.

Material and labour for water proofing treatment of sunken floor of WCs, bathroom etc. by applying of the following specifications :- (i) Cleaning of sunken floor surface with mechanical means i.e. wire brush/air blower etc. and remove all loose/unsound material, dirt, dust, etc. (ii) Applying cement slurry mixed with acrylic based polymer modified cementitious composite compound coating Hydroproof Xtra of FOSROC/Equivalent of Dr Fixit of Pidilite Industries Ltd in the ratio of 1:2:4 (One part of acrylic polymer : Two part of water and four part of cement). (iii) First layer of cement slurry @ 0.444 Kg/Sqm mixed with acrylic based modified cementious composite compound @ 0.222 Litre/Sqm and allow it to air dry for 04 hours. (iv) Second layer of cement slurry @ 0.222 Kg/Sqm mixed with acrylic based polymer modified cementitious composite compound @ 0.111 Litre/Sqm and allow it to air dry for 04 hours followed with water curing for 48 hours. (v) 200 micron thick polythene film shall be pasted with help of adhesives over treatment. Note :- Joints of WC/Trap/Soil waste shall be properly sealed with sealing compound. Testing of all traps and joint and sunken slab shall be done as per IS-1742 before filling and tiling work.

Material and labour for plain cement concrete 1:5:10 type E-2 (using 40mm graded broken bricks aggregate) as in foundation, filling and mass concrete, complete all as specified and as directed.

Material and labour for 25mm thick plain cement concrete 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in levelling courses laid and compacted in slope in floor complete all as specified and as directed.

S&F strudctural steel MS angle, channel, flat iron etc, as in roof trusses, purlins , posts etc. including distance pieces etc conforming to Fe-410-W (Gde-E-250) complete all as spd.

M&L 100 mm thick cement concrete type C-2, 1:3:6 (20 mm graded stone aggregate) as in sub floors, filling and mass concrete etc

M&L screed bed or bedding layer of cement mortar (1:4) 15mm thick for laying floor finishes/pavers complete all as specified and as directed.

Coloured Chequred cement conc tiles (30cmx30cmx25mm thick) in grey cement and with pigment in floors etc , set and jointed in neat cement slurry, ocomplete all as specified and directed.

Excavation in trenches n.exc 1.50m wide and not exceeding 1.50m depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shapts, cesspits, manholes, peir holes, etc. and getting out out in Hard /dense soil complete all as specified and as directed by Engr-In-Charge.

Demolition of cement concrete (unreinforced) of any description and in any position not otherwise specifically provided for complete all as specified and directed.

Demolition and breaking up drain pipes 150 mm dia (Salt glazed ware,AC or Reinforced concrete) set in cement morter.

Demolition and breaking up drain pipes 200 mm dia (Salt glazed ware,AC or Reinforced concrete) set in cement morter.

Material and labour for 150mm bore sail -glazed stoneware drain pipess laid in trenches and jointed as specified and directed by Engr-in- Charge.

Material and labour for 200mm bore sail -glazed stoneware drain pipess laid in trenches and jointed as specified and directed by Engr-in- Charge.

M&L for concrete bed to drain pipes 150mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C2 using 40mm graded stone aggregate including demolition of damaged concrete complete all as specified and as directed by Engr- in-Charge.

M&L for concrete bed to drain pipes 200mm bore including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C2 using 40mm graded stone aggregate including demolition of damaged concrete complete all as specified and as directed by Engr- in-Charge.

M & L for PCC 1:4:8 type D-2 Using 40 mm graded stone aggregate as in foundations , filling and mass concret complete all as specified.

M&L Brick work with subclass ‘B’ bricks, straight or curved on plan exc 6m mean radius, built in cement Mortar 1:4 as in manholes complete all as specified and as directed by Engr- in-Charge.

M&L for extra for forming fair finished drain or channel 30 cm inner girth in cement concrete using extra cement including forms mould stopped ends complete all as specified and as directed by Engr- in-Charge.

M&L for cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate in surface channels, drains and coping including form work complete all as specified and as directed by Engr- in-Charge.

M & L for cutting into exising manholes for connecting new drains, making good to pipe & rendering, cutting out existing benching for & forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B1, smooth finished & reforming benching as required for internal dia of pipe 150mm. complete all as specified and as directed by Engr- in-Charge.

Material and labour for Precast cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in cover slabs of manholes, gully traps etc set in cement mortar (1:4) complete all as specified and directed.

Returning, filling in excavated approved soil spreading, levelling, watering and well ramming in layer n exc 25mm each complete all as specified and as directed by Engr- in-Charge.

Removing of excavation material n exc 50 mtr and deposited where directed at a level n exc 1.50 mtr above the starting point complete all as specified and as directed by Engr- in-Charge.

Taking down carefully copper/AImn point wiring (Light,Fan/Point Socket or power) (fittings such as switches ceiling roeses, pendent, regulators, sockets etc to be measured & paid seprately) & making good to disturbed surface of walls/floors etc.

M&L point wiring using approved colour coding as per IS with stranded copper conductor single core 1.5 Sqmm (Nominal area), PVC insulated cable in and incl PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories incl mild steel sunken boxes suitable for mounting switch/sockets with earth dolly duly painted with two coats of anti corrosive paint over a coat of red oxide primer incl mounting frame over cover plate, covered with 3mm thick plastic laminated sheet, incl PVC insulated copper conductor 1.5 Sqmm (Nominal area) single core PVC cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified. Note : Switch/sockets shall be measured and paid for separately :-

One light/fan point controlled by one switch complete all as specified.

One switch socket outlet 3 pin,5 Amp on the independent board complete all as specified.

One switch socket outlet 3 pin,5 Amp on same board complete all as specified.

One light point controled by two way switches with cables 1.5 Sqmm size complete all as specified.

One bell/buzzer point controlled by one push button on the same board with other switches or independent with cables 1.5 sqmm size complete all as specified.

All as per item No 124.00 here-in-before but with 2 single core PVC insulated FRLS and sheathed copper conductor of size 2.5 Sqmm in and including PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories with 2.5 Sqmm PVC insulated FRLS copper conductor as earth wire and connecting to common earth dolly for 6 pin 16 Amp socket outlet on the independent board.using 2.5 sqmm copper cable incl PVC insulated copeer conductor 1.5 Sqmm as continued earth wire.

All as per item No 124.00 here-in-before but with 2 single core PVC insulated FRLS and sheathed copper conductor of size 4.0 Sqmm in and including PVC conduit (ISI marked) including cutting chiseling and grouting concealed PVC conduit pipe, tee, elbow and bend etc.and with all connecting accessories with 4.0 Sqmm PVC insulated FRLS copper conductor as earth wire and connecting to common earth dolly for 6 pin 16 Amp socket outlet on the independent board.

S&F bell push, 6 Amps, SP, flush type complete all as specified.

S&F Electric Bell , AC 230 volts, single pole complete all as specified.

M& L switch piano, flush type, single pole 2 way 6 Amp,ISI marked complete all as specified.

S&F Lamp holder,PVC insulated body, with back plate suitable for batten fitting complete all as specified.

M& L switch piano, flush type, single pole 1 way 6 Amp,ISI marked completeall as specified.

S&F switch piano flush type, single pole 1 way 16 Amp complete all as specified.

M& L socket 5 pin 6 Amp piano flush type,ISI marke complete all as specified.

S&F socket out let 2 in one 6 pin 6 & 16 Amp complete all as specified.

S&F ceiling rose, 3 phase/ PVC/ polycorbonate,isolate bady complete all as specified.

S & F LED bulb 10 watt complete all as specified.

Supply and fixing Aluminium housing LED 22 Watt inverter batten with inbuilt Li Ion battery for power backup of 2 to 3 hrs complete.

S&F Decorative wall light fixture made up of Polycarbonate , fancy type, made out of Polycorbaonate,suitable for B-22 base holder fixed as in repair complete all as specified and directed.

S&F sleek LED mirror light with diffuser 7/ 9 watt along with all accessories prewired including connecting with copper flexible cable of size 0.7 Sqmm 3 core and all as specified and directed .

S & F Bulkhead luminaire Decorative Energy saving new generation 10W LED IP65 with opal diffuser incl electronics driver & connection with copper flexible cable 3 core complete all as specified and directed.

S & F LED Building security light30 wattLED Inverter RTC inbuilt for AUTOON/AUTO OFF and must have dimming facility from 10 to 100% of rated wattage as peruser defined timeline made pressure die cast housing with individuals LEDs & Lens with modular secondary optics and IP65 protection with electronics driver and copper conductor 3 core of 0.7 sqmm from ceiling rose to security light with Bracket made out of GI light grade pipe of 32 mm dia 1.5 mtr long bend to an angle of 120 degree with fixing arrangements on wall Complete all as in repair.

Supply and fixing wall Mounting LED fitting 9/12 watt 6500K 2 ft Basic all purpose surface and wall mounted led batten with polycarbonate housing & integrated electronic driver complete all as specified and directed.

S&F sheet metal enclosure with double door SPN for DBs conforms to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 8 way, 240 Volt SPN.

S&F sheet metal enclosure with double door TPN for DBs conforms to IS:8623.III , IP:43 protection, shrouded neutral bar and cement spill protector, 4 way, 415 Volt TPN.

S & F MCBs 'B' characteristics, Double pole , 240 V, 32 Amp breaking capacity 10 kA complete all as specified.

S & F MCBs 'B' characteristics, Four pole , 415 V,63 Amp breaking capacity 10 kA complete all as specified.

S & F MCB B characterstic single pole 5 to 30 Amp, 240 volt breaking capacity 10 kA complete all as specified.

M&L for submain wiring with 2 single core PVC insulated FRLS cable 6 Sqmm copper conductor PVC sheathed in and including rigid PVC concealed conduit heavy duty of suitable size incl cutting chiseling of wall and making good to disturbed surface of walls / floor etc with plastering painting etc so as to match with the existing finishes, drawn with 6 Sqmm PVC insulated FRLS copper conductor cable for earth wire fixed with shaddle and connecting to common earth teriminals complete all as specified.

Single pole and Neutral Sheet metal enclosure with a 2 pin and earth plug and socket complete with one single pole MCB 20 Amps complete all as specified.

S & F Non mettalic Electric meter box with single hinged door for 01 No. Single phase meter of size 250 X 200 X 105 mm after disconnecting the supply of electric meter and fixing the electric meter on meter box incl reconnecting the electric supply complete all as specified.

Supply & Fixing exhaust fan, energy efficent metalic blades heavy duty turbo force of size 300 mm sweep, 900 rpm, AC, 230 volts complete with louvers, shutters, mounting on walls with holding down bolts, nuts, washers with cutting holes into or through stone/brick walls for fixing of 450 mm sweep exhaust fan including making good the cutting and matching the surface with existing surfaces and connection of flexible copper conductor cable three core ceiling rose to fan and testing complete all as specified.

Earthing complete with and including galvanised steel earth plate electrode 60 cmx 60cm x 6 mm thick surrounded by mixture of charcoal and salt in alternate layers , buried directly in ground vertically in a pit of depth not less than 2.25 meter deep below ground level with top as of the plate at a depth of not less than 1.5 mtrs below normal ground level connected to galvanized iron or steel earth lead wire 4.0 mm dia,( NO 8 SWG) by means of bolts ,nuts, check nuts and washers of galvanised iron or steel earth wire protected by galvanised steel pipe 15 mm bore (light grade) and connected to main switch or main control board all as shown in electrical plate No. 3 of SSR - 2009(Pt I) & including necessary excavation and earth work.

The rate also include charcoal and salt in alternate layers, 20 mm bore GI pipe (Light grade ) for watering , protection pipe funnel, wire mesh , PCC 1:2:4 type B1 chamber in cement concrete ,50 mm thick precast RCC M-25 ( Normal mix) cover duly reinforced with XPM (weight not less than 3 kg /sqm ) and CI frame etc , and including provision of test point , connecting to test point and testing on completion etc, complete all as specified. NOTE : The unit rate include earthing lead and protection pipe upto 6.5 metre from top of earth plate.

Supply & laying or fixing or passing through pipe, 1100 volts grade heavy duty cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured wit galvanised steel wire or tape and overall PVC sheathed 10 Sqmm nominal cross section,4 core ,stranded conductor , in service connections

Sand filling under floors or in foundations including watering and consolidation complete all as specified.

Supply and Laying Bricks old size sub class 'B', of class designation 10, for the protection of cable laid flat dry across the cable complete all as specified.

Tubes, light grade, galvanised 40 mm dia with all fittings laid in trenches or fixed on walls etc complete all as specified.

Amount of credit of Rs. 117102.20 for retrived old material as mentioned in Schedule 'A' section-II of tender document in pdf form, will be deducted offline while acceptence of tender.

AUKTA ENERGY PRIVATE LIMITED

M/s Parmod Kumar

S R AND CO

karambir constructions

M/S SHANTI SARUP DINESH CHAND