Spl repairs to bldg No P-2/2, P-2/3 GN Rd and 15/7, 15/8 JS Arora Enclave under GE (West) JRC

Amount

Dismantling of brick tiles single layer as in roof covering complete all as specified

Demolition of mud in roofs any thickness including plastering and leeping (whether full thickness removed or only a part thereof) and washing the surface thoroughly to remove all mud complete all as specified.

M & L brushing neat cement slurry with 3kg of cement per sqm complete all as specified

M&L for P.C.C 1:2:4 type B0 using 12.50 mm graded stone aggregate as in padding over roof finished and laid to required slope complete all as specified and as directed.

M&L for 10 mm thick rendering in cement mortar 1:4 on concrete surfaces when concrete is stilL green finished even and fair including mixing of water proofing compound as per manufacturer instruction etc complete all as specified and as directed. Note :- Water proofing compound shall be measured separately.

Supply only Liquid water proofing compound complete all as specified and as directed.

M&L for liquid Polyurea-PU based hybrid elastomeric water proofing membrane including fibre mesh between the PU coats at existing/newly constructed roofs, RCC structure like basement raft, retaining wall, water retaining structure, tunnels/subways and bridge deck etc. in two or more coats. The product must have pot life of >90 mins., tensile strength > 12.6 Mpa, elongation of > 500% conforming to ASTM D 2370 & puncture resistance of >200 N as per ASTM E 154 with min. consumption of 1.5 Kg per sqm for 1.2mm DFT in two- three coats. The surface needs to be primed with water soluble self impregnated epoxy primer in two coats to be applied @ 200-250 gms/sqm/coat prior to Polyurea -PU application. Furthermor, (in case the substrate is not suitable) 15mm plaster is advisable for surface prepration before application of the water proofing membrane to avoid pinholes or functional difficulties of the system. Note:- The application shall be done by the authorised applicator of the manufacture with a letter of proof stating the authenticity of the applicator firm.

M & L 40mm thick Brick tiles laid on bedding layer of CM 1;3 15mm thick and joints grouted flush in cement mortar 1:3mixed with 5% of crude oil by weight of cement over APP membrane complete all as specified and directed.

M & L 40mm thick Brick tiles laid on bedding layer of CM 1;3 15mm thick and joints grouted flush in cement mortar 1:3mixed with 5% of crude oil by weight ofcement over APP membrane except tiles complete all as specified and directed.

M & L flush pointing in CM 1:3 to brick tiles laid flat in roof or paving incuding raking out joints complete all as specified and directed.

Taking up or down existing steel 15 mm tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed

Taking up or down existing steel 20 mm tubing and connections including cleaning for refixing or removal to store complete all as specified and as directed

Supply & fixing, 15 mm jointing and testing galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed.

Supply & fixing, 20 mm jointing and testing galvanised iron tubing medium grade with all fitting such as bends, elbow, socket, reducer etc and fixed to wall or laid in floor complete all as specified and as directed

Dismantling of water tanks (PVC/RCC of any description) exc 250 ltr and n.exc 500ltr capacity and removing from site complete all as specified and as directed.

Dismantling of water tanks (PVC/RCC of any description) exc 500 ltr and n.exc 1000 ltr capacity and removing from site complete all as specified and as directed.

S&F 500 ltr capacity rotational moulded polythene water storage tank (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F 1000 ltr capacity rotational moulded polythene tanks (cylindrical vertical with closed top) hoisted and fixed in position complete all as specified and as directed.

S&F in repairs 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (Minium weight 210 gms ), complete all as specified and directed.

S & F in repair 20 mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

S & F in repair 15 mm dia Gun metal gate valve with iron wheel head, screwed both ends for iron pipe complete all as specified and as directed.

Demolition and breaking up drain pipes AC/PVC pipe in event n.exc 150 mm dia including all fittings.

S&F for 110 mm PVC (SWR) Rain water pipes single socketed in any length with rubber ring joints fixed to walls all as specified and directed

S&F 110 mm bore PVC (SWR) bends in any radius complete all as specified and directed.

S&F PVC (SWR) junction single (single tee) equal or unequal, dia of pipe 110 mm complete all as specified and directed.

S & F 75 mm bore PVC (SWR) pipe of pressure rating 4kgf/cm2 single socketed in any length with rubber ring joints jointing with adhesive fixed in repair to wall/laid in trenches complete all as specified and directed.

S&F 75 mm bore PVC (SWR) bends in any radius complete all as specified and directed.

S&F PVC (SWR) junction single (single tee) equal or unequal, dia of pipe 75 mm complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap with grating including joining to waste pipe fixed in solvent cement incl taking down damaged floor trap in any position complete all as specified and directed.

Taking down cement plaster of any description any thickness /dado/Skirting/ including raking out joints hacking for key scrubbing down with water all as specified.

Demolition of brick work built in cement mortar incl all quions, arches pillars etc but excludding precast concrete articles all as specified.

M&L for brick work with sub class 'B' old size bricks straight or curved on plan to any radius with old size brick thick walls built in cement mortar 1:6all as specified.

M&L for 15 mm thick cement mortar 1:4 on brick or concrete surface finished even and smooth without using extra cement all as specified

M&L for preparing new plastered or unplastered wall surfaces and Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)all as specified and directed by Engr-in-charge.

M&L for complete removal of existing treatments on wall surfaces and applied two coat of weather coat over one coat of primer all as specified and directed by Engr -in-charge.

M&L for 15 mm thick cement mortar 1:6 on brick or concrete surface finished even and smooth without using extra cement all as specified

M&L for preparing surfaces new plastered surfaces of walls by applying two coats of oil bound distemper over a coat of 1mm thick wallcare putty on plastered surface preparatory to distempering complete all as specified.

M&L Complete removal of existing treatment of wall surfaces applying two coat of oil bound distempering over a coat of wall care white putty on plastered surface all as specified and directed by Engr-in-Charge.

M&L Plastering 5mm thick in cement mortar (1:3) finished even and smooth without using extra cement as on ceiling complete all as specified

M & L for preparation of new plastered surfaces of Ceilings and applying three coats of white wash etc. complete all as sepcified and directed

M & L for preparation of old plastered surfaces of ceilings and applying two coats of white wash etc. complete all as sepcified and directed

M & L for preparation of old plastered surfaces of walls (for washrooms) and applying two coats of white wash etc. complete all as sepcified and directed

S&F in repairs vitreous China wash down water closet pan (pedestal pattern) white including bolts, flushpipe of polyethylene of low or high density or PVC 32 mm dia anti syphonage pipe etc complete

Supply and fixing plastic water closet seat cover white closed patern with flat bottom and cover and mild steel chromium plated or aluminised hinging devices

S & F S&F brass chromium plated health faucet Cat Part No: ALD -565 for pedestal pattern water closet including PVC flexible pipe along with complete necessary fittings complete all as specified and as directed.

M&L for fixing in repairs vitreous China squatting pan, ‘Orissa’ pattern (IWC) size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe) Pedestal pan and trap, including connection to drain (or outgoing pipe) and to flushing pipe, anti-syphonage pipe, etc.. complete.

Supply and fixing in replacement chromium plated grating 125mm dia circular fixing with cement mortar 1:3 on nahani trap/floor trap complete all as specified and directed.

S&F sinks with drainage board made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm

M&L for 25 mm thick granite machine cut as incooking platform bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone laid over bedding layer or screed 15 mm thick screed bed in cement mortar 1:4 including cutting , grinding, rounding edges, rubbing and polishing complete all as complete all as specified and directed by Engr-in-Charge.

Material and labour for 25mm dia Stainless steel pipe curtain rod, powder coated fixed with & including SS hooks/ brackets and SS decorative finials (at both side), shade as approved by GE complete all as specified includng fixing of long size rawl plugs in wall for SS hook complete all as specified and directed.

S&F in repair Stop valve (Concealed) ,15 mm cast copper alloy with long shank &cup with capstan heads, screwed down, high pressure, with crutch or butterfly handle screwed for 15mm bore iron fixed fancy type complete.

S&F in repair 15mm angular stop valves, fancy type chromium plated, with long shank and cup(concealed) screwed down, high pressure with crutch or butter fly handle screwed both ends for iron pipe or for unions and fixed .

S&F in repair Bib tap fancy type (Long body) cast copper alloy suitable for 15mm bore iron pipe with long body fancy type complete fixed in repairs .

S&F PVC valve less symphonic action type flushing cistern, low level white with inlet ball valve float and handle with flush pipe 10 Ltr capacity complete all as specified fixed in repairs.

S&F connection pipe braided with wires (reinforced) 45cm long with brass check nut and PVC washers at both ends complete all as specified and directed.

S&F Hot and cold basin mixer fancy type single or double legged cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends iron pipe suitable for 15mm bore pipe fixed to wash hand basin complete all as specified.

S&F Hot and cold wall mixer fancy type single or double legged cast copper alloy screwed down high pressure with crutch or butterfly handle screwed both ends iron pipe suitable for 15mm bore pipe fixed to wall complete all as specified.

Supply and fixing Vitreous china wash hand basin (Oval shape) under counter type bowl type including waste coupling and pipe all as specifed and directed.

S&F brass chromium plated shower rose of 150 mm size (Square shape) and 450 mm long CP arm, with or without swivel joints including fixing to steel pipe or union all as specified and directed by Engineer - in - Charge.

S&F Brass chromium plated tubular tower rail 20mm dia , D type, 60cm long between flanges complete

S&F 5 mm thick Glass corner shelf including CP railing, radius 300mm complete all as specified and directed.

S&F 5 mm Glass Straight shelf 600 x 125 mm including CP railing complete all as specified and directed.

S&F Brass CP Soap dish, any type, fixed to plugs with chromium plated brass screws all as specified and directed.

Taking down chowkhats or frame with shutter w/o taking off shutter from the frame area not exc 1.5 Sqm each all as specified.

Taking down chowkhats or frame with shutter w/o taking off shutter from the frame area exc 1.5 Sqm but n exc 4.00 sam each all as specified.

Taking down shutters of any description n. exc 1 Sqm each complete all as specified and directed.

Taking down shutters of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified and directed.

S&F 25 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed. (For Wardrobe shutters)

Mild steel conforming to Fe 290, Gde E-165 framed work as in door frames, chowkhats including necessary cutting, welding, bending, drilling etc., complete all as specified and directed.

S&F 2nd class hardwood 35mm thick factory made plain, framed, panelled shutters (two panels) withlock rail and panel of 9mm BWP commercial ply or12mm veneered particle board with commercialveneering on both faces. The size of rail and stile asper IS : 1003 (Part-I), kiln seasoned and chemically pressure treated

S&F glazed and skelton shutters 35mm thick open rebated and prepared to receive glass,gauge etc (without sash bars) edging of framing plain, chamfered or rounded with cut and mitred beads for securing glass etc. sizes of members of shutters as specified in SSR Pt-I, Section 8, Clause 8.24(a).

S&F 250 mm longMild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified.

Preparation of new steel surface of any description over 10 CM width or girth and applying two coats of synthetic enamel paint complete all as specified

S&F powder coated aluminium frame for doors,windows, partitions ,ventilators with one or more rebates including joining cleat for fixing etc complete all as specified.

S&F powder aluminium window and ventilator shutters (Sliding type) without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

S&F sheet glass 4.8 mm thick ordinary quality to be fixed in Al frame work in square exc 0.5 sqm in each pane

Anodised aluminium grill (powder coated) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixingapproved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer in-charge.

S&F steel window 1.25mm thick box type (primer coated) ERW hollow P section of size 60x25mmsingle rebated comprises gauged skelton shutter ERW sec 50x20mm and 1mm thick with two open able leaf consisting two Nos sash bars of T section 20x3mm completed welded to frame with one vertical mullion of ERW box type T section of size 60x25mm and 1.25mm thick incl cutting holes and making good dismantled portion PCC 1:2:4 type B1 four Nos for each window incl following fittings weld to frame shutter (a) hold fast, 150mm long of 12mmx3mm made to shape-04 Nos per window (b) handle of Z sction 20x25mm, 100mm long 01 Nos per leaf (c) MS Tower bolt 150mm long of 12x3mm made to shape-04 Nos per window (b) handle of Z section 20x25mm, 100 long stoper-01 No per leaf () MS pintal of hinges of size 75mmx12mm-02 Nos per leaf (g) fabrication & fixing arrangement as per Drg No. CEJZ/TD-06-07 , Note : wire mesh/Glass and painting shall be measured and paid separately under appropriate item.

M&L for sheet glass 3mm thick ordinary quality and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in each pane.

S&F galvanized mild steel wire cloth 0.56 mm nominal dia and average width of aperture 1.18 mm and fixed with tinned tacks.

S/F PVC solid door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinfoced with MS square tube, suppling and fixing in opening as per specification and drawing.

S&F factory made solid panel PVC door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing.

M&L 2nd class Hardwood Plain fillets. Cross section 2.50 sqcm square 9 sqcm exc 6sqcm and n.exc 13 sqcm rectangular or triangular in section, clean sawn, secured with nails or brads complete all as specified and directed. (For framework of forthcoming item below)

M&L 18/19mm thick prelaminated particle board exterior grade prelaminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber framed work including taking down fixing arrangement complete all as specified

M & L for 18-19 mm thick for external teak wood lipping, 6mm thick fixed with nails

S&F floor door stopper aluminum alloy body anodized with hard drawn steel spring overall length 150mm

S&F continuous piano hinges mild steel bright finish of flap width 40mm

M&L Hasp and staple safety type aluminum anodised 75mm size with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified

Preparation of new wood and wood based surfaces of any description over 10CM width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for Preparing old wooden surfaces and applying one coat of synthetic enamel paint over Surfaces of any description, over 10cm in width or girth

M&L for Preparing old steel surfaces and applying one coat of synthetic enamel paint over Surfaces of any description, over 10cm in width or girth

Supply & Fixing 100mm size stainless steel butt hinges heavy grade extruded stainless steel hinge plate complete all as specified.

S&F Aluminum anodized barrel tower bolt of extruded section of size 150mm complete all as specified.

S&F extruded Aluminum alloy handle fabricated of size 150mm all as specified and directed

S&F extruded Aluminum alloy handle fabricated of size 100mm all as specified and directed

S&F in replacement aluminium (die cast body) door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 Kg complete all as specified as directed.

Dismantling floor hearth or wall tiling including cement mortar bedding ( but not backing) and disposal of rubbish outside MD land complete all as specified

Given sunken floor shall be treated as per following instructions and directed by Engr in Charge :- (A) The surfaces to be applied shall be completely dry and free from containments such as dirt, dust, oil, surface treatments and old coatings. Concrete substrates must be mechanically prepared using abrasive blast cleaning or miling to remove cement laitance, existing coatings and achieve a gripping profile that is clean dry and free from laitance and any other form of surfece contamination. The installation instructions n manufacturer's published literature should be strictly complied with, includingf but not limited to the following:- (aa) Chipping out any visible cracks in "V-Groove" pattern as applicable. Special attention on this part. Cleaning of cracks and then filling those cracks with SIKA latex SBR 100 putty/Dr fixit 302 SBR latex/ Perma Latex SBR/ FOSROC Nitabond SBR latex/ Asian Paints latex as required. Final cleaning of surface with power grinder, Wire brush, hair brush & vacuum pressure if required. (bb) Dampen all surfaces immediately ahead of application of Acrylic modified Cementitious coating of SIKA Top Seal-107/ Brush bond FOSROC/ DR Fixit/ STP/CICO. (cc) Whilist the surface is still damp from saturation (S.S.D), apply one coat of Acrylic modified Cementitious coating of SIKA Top Seal-107/ Brush bond FOSROC/ DR Fixit/ STP/CICO of viscosity as per manufacturer's instructions. (dd) Apply glass febric sheet of Sika Fab 1/FOSROC/ DR Fixit/ STP whilist the first coat is wet. (ee) Once touch dry, apply second coat of Acrylic modified Cementitious coating of SIKA Top Seal-107/ Brush bond FOSROC/ DR Fixit/ STP/CICO of viscosity as per manufacturer's instructions on the entire area. (ff) Second coat shall be applied 6-8 hours of application of previous coat and in the direction right angle to the previous coat. (gg) The waterproofing coating should be taken to a height minimumn300 mm above the finished floor level on the vertical surface. (hh) It is essential to cure Acrylic modified Cementitious coating immediately after application (minimum 6-8 hours drying) for a minimum of 3 to 5 days to ensure full cement hydration and to minimize cracking.

A protection plaster 15mm thick in CM 1:3 admixed with appropriate Integral water proofing compound has to be applied on the walls. Admixture : SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO confirming to IS 2645.

Providing and applying a protection screed of 50 mm thick 1:4 cement sand mortar admixed with Sika Plastocrete over the applied water proofing coating on horizontal surface. Admixture : SIKA Plastocrete Plus/FOSROC/ DR Fixit/ STP/CICO confirming to IS 2645. (kk) All the corners and joints should be pretreated with an elastic waterproofing sealing tape withy a wooven bonding mesh on each surface ab=nd an elastic expansions zonbe in the centre of Make Sika Seal Tape S/FOSROC/ Dr Fixit/ STP. (ll) The membrane has to be protected in accordance with the manufacturer's recommendations until placement of concrete. The membrane to be inspected for damage just prior to concrete placement and make repairs in accordance with manufacturer's recommendations. (mm) Waterproofing/Sunken floor treatment has to be carried out through applicators authorised by the respective manufacturers and approved by GE.

Supply and applying of crack bridging water proofing sealing tape, Sika deal F tape.

M & L 25mm thick cement concrete flooring type B-1, 1 :2 : 4, using 20 mm graded stone aggregate finishing cement concrete surface even and smooth without using extra cement.

M& L Cement concrete type E-2, 1:5:10 using 40mm graded aggregate in foundations filling and mass concrete as in sunken floor.

M&L for non-skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors set and jointed in neat cement slurry and pointed in white or colored cement to match over and incl 15mm thick bedding layer CM 1:6 complete all as specified. (Colour and shade as approved by Engr-In-Charge)

M&L for non-skid ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in skriting set and jointed in neat cement slurry and pointed in white or colored cement to match over and incl 10mm thick rendering as backing coat of CM 1:4 complete all as specified.

M&L for vitrified ceramic tiles light shade 10 mm thick (Square/rectangular) polished m area of each tiles not exceeding 0.36 Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15 mm th screed bed in CM 1:6 complete all as specified. (Colour and shade as approved by Engr-In-Charge)

M&L for vitrified ceramic tiles light shade 10 mm thick (Square/rectangular) polished m area of each tiles not exceeding 0.36 Sqm , in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10mm thick rendering as backing coat of CM 1:4 complete all as specified. (Colour and shade as approved by Engr-In-Charge)

M&L for coloured glazed tiles of size 450x300x7 mm thick in dados set and jointed in neat cement slurry and pointed in white or colour cement to match including 10 mm thick rendering in CM 1:4 complete all as specified and directed. (Colour and shade as approved by Engr-In-Charge)

M&L for 50mm PCC 1:3:6 type C1 using 20mm graded aggregate as in plinth protection and path finishing the surfaces even and smooth without using extra cement all as specified

Demolition of reinforced cement concrete of any description and in any position complete all as specified and directed.

Reinforced cement concrete 1:2:4 type B-1 using 20 mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies , canopies , deck slabs and in shelves and the like complete all as specified and directed.

Mild steel high yield strength TMT bars 10 mm dia and over cut to length bent to shape require including, cranking, hooking ends, bending and binding with and including MS wire (annealed) not less than 0.9 mm dia complete all as specified and directed

Form work to soffits of suspended slabs such as roof slabs, floor slabs, shelves landing and similar work not exceeding 200 mm thick (horzontal or sloping) and to edges of concrete complete all as specified and directed

Dismantling posts or struts embedded in concrete (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground

M & L for PCC (1:2:4) typeB-2 (using 40mm graded crushed stone aggregates ) lean concrete as in foundation, filling and mass concrete of post complete all as specified .

S&F rolled sections as in main and cross beams,hip and jack rafters,purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates. confirming to grade Fe-410-W gde E-250 Quality A complete all as specified and directed by EIC.

S&F pre-painted galvatume aluminium zinc coated GI based corrugated steel sheet 0.50mm thick of colour (as approved by users) having tensile strength of 550 Mpa with powder coating 150 gm per sqm as in roof covering/cladding to walls,fixed with self tapping screws as specified and including dismantling old/Unsv sheets.

Supply & Fixing iron angle post and struts in fencing including cutting top to shape as direct drilling holes notching for wire etc, flat iron fillets (for screwing wire mesh etc) incl all necessary drilling bolting/bolts and nuts or reveting etc and similar work conforming to Fe 209 Gde E 165..

Supply only MS galvanised chain link fencing n exc 4 Kg/Sqm

Fixing only chain link fencing including line wires, any mesh size and type to any type of standards, rails, straining bolts etc including provision of binding wire

Hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 all as specified and directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete Fe 410 -W (Gde- E- 250) quality- A

M&L for repairing of R.C.C projections, chajjas, roofs, facia etc by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.,C.C surfaces with cement concreat (1:1.5:3) using 12.5mm graded crushed stone aggrigates and reinforcement with welded mesh (If Reqd) of weight exc 2 kg per sqm but n.exc 3kg/sqm with or without facia and finished with cement and sand motar (1:3) using coarse sand and work in patches area n.exc 5 sqm each and thickness of R.C.C member n.exc 70mm including necessary form work and applying two coats of finishes to match with the existing surfaces in at any height complete all as specified and directed by Engr-in-charge. (Note : Welded mesh measured and paid seperately)

S&F 1.25 mm lath steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type.

S&F in repairs PVC Modular kitchen cabinet box type made of 18 mm thick PVC/WPC board of approximates 2.0 x 0.80 x 0.60 mtr incl all telescopic sliding channels, stainless steel handles, stainless steel knobs, stainless steel hinges, including atleast 01 x SS sliding plate rack, 01 x SS sliding Basket and 01 x SS sliding cutlery drawer etc complete all as sped and directed by Engr-In-Charge.

S&F in repairs PVC Modular kitchen cabinet box type made of 18 mm thick PVC/WPC board of approximates 1.20 x 0.16 x 0.60 mtr incl partitions , front top hung glass shutters , SS hinges etc complete all as specified and as directed by Engr-In-Charge.

M&L for 20 to 25 mm thick machine in cut kota stone slab for treads (Single piece stone) & landings of stair cases over and incl 15mm thick bedding layer CM 1:6 with pigments to match the shade of slab including cutting, rubbing and mirror/granite finish polishing complete all as specified and directed by Engr-in-Charge.

-Ditto- all as per item No: 6 above but on vertical surfaces such as riser (Single piece stone) etc over and incl 10 mm thick cement plaster in CM 1:4 at in back coat rough finished surface to receive tiles complete all as specified.

Rounding/moulding to edges of Kota stone slabs/marble stone/granite stone slabs one edge, such as in steps, cooking platform , and other similar situations etc complete all as specified.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors etc.

Taking down unserviceable Submain/Cable of any size as directed by Engineer-In-Charge.

Taking down main switch / DB as directed by Engineer-In-Charge.

M & L for concealed point wiring complete with 1.5 sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 650 /1100 volts grade drawn through & including PVC conduit ,medium grade with accessories like bends, tees, junction boxes etc fix on wall or ceiling surfaces all as specified including 1.5 sqmm , FRLS type , copper multistranded cable as earth wire including sunken type pressed steel terminal boxes of thickness 1.6 mm thick and plastic laminated white / coloured top sheet cover 3.0 mm thick for: One light / fan/bell point controlled by one, one way switch.

One 3 pin socket out let 5 Amps on same board.

One 3 pin socket out let 5 Amps on the independent board.

Ditto all as per item No.4 about but with 2.5/4.0 sqmm multistranded copper multistranded conductor FRLS cable with 2.5 sqmm earth wire for one 6 pin socket outlet 15 amps on independent board/AC point as per item no. 25 complete all.

S & F switch Piano 5 Amps, flush button type, SP, one way, 230 Volts, AC

S & F switch Piano 1 5 Amps, flush button type, SP, one way, 230 Volts, AC

S & F socket out let multipurpose 5 pin 5 Amps,230 Volts

S & F socket combination ,6 pin ,15 amps, flush type, multipurpose, 230 V

Supply and fix bell push flash piano type 5 amps complete all as specified and directed.

Supply and fix bell ding dong 230 Volts AC single pole complete all as specified and directed.

M & L ceiling rose surface bakelite 65 x 50 mm three terminals complete all as specified.

Supply and fix MCB DB, TPN 4 way double door with suitable 200 amps rated bus bars , Neutral links , blanking plates conforming to Osafe of HPL / Acti 9 series of Schneider /Ekinox3 of Legrand /equivalent in Havells/Hager/L&T/Siemens complete all as specified and directed. all as specified and directed.

S/F MCB TPN 40 Amps 415 volts as per Osafe of HPL / Acti 9 series of Schneider /Ekinox3 of Legrand /equivalent in Havells/Hager/L&T/Siemens complete all as specified and directed.

Supply & Fixing MCB single pole, 240 volts, 6 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type conforming to Osafe of HPL / Acti 9 series of Schneider /Ekinox3 of Legrand /equivalent in Havells/Hager/L&T/Siemens complete all as specified and directed.

Supply and Fixing stepped socket type electronic fan regulator and connecting up complete all as directed by Engineer-In-Charge.

M & L Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings incl 12 W LED bulb complete all as specified and directed.

S&F in replacement LED tube light fitting 20W box type including LED lamp 20 W with 2200 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI-6500K (White light) fixtures and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.75mm 3 core complete all as specified and directed.

S & F SITC of high-quality integrated LED Street Light with a minimum system lumen of4750 Lm and system wattage not exceeding 45W with a nominal efficiency 105 lumen/watt. CCT of 5700K with SDCM of < 5 and CRI >70. The housing should be of non-corrosive high-pressure die-cast aluminum with high efficiency LEDs as lighting source and lens embedded PC cover having TOP Opening seperate driver compartment with IP66 protection and impact resistance of IK07 with PF > 0.95. Lifetime of 50K hours @L70. The Luminaire should have Powered by integral, Isolated LED electronic driver (SMPS based constant current supply) with lower THD, Output Open / Short Circuit protection, Phase to Phase protection (Operation at 440 V AC), Over Voltage protection, Surge Voltage protection upto 4 kV.Manufacturer shall have inhouse lab approved by NABL or ministry of science of govt of India. LM 79 and LM80 reports need to be submitted from a NABL/ULaccredited lab to verify above parameters complete all as specified and directed.. Havells Cat no ENDURASUNBEAMSL45WLED757SASYTOPCSENSO equivalent in Signify/Wipro

Supply & fixing decorative wall light fixture made up of polycarbonate/glass all as specified and directed.

Supply and fixed LED Bulk head light fitting cap 10 Watt all The luminaire should have a color CRI > 80, and CCT of 5700K. The luminaire shall be compliant with IP66 & IK 10 classification. Luminaire shall be designed to emit at least 1000 nominal lumens at a system efficacy of at least 100 lumen/watt with a maximum system wattage of 10 Wattsas specified and directed.

M & L for sub main wiring with two single core PVC insulated and unsheathed cable 4 sqmm with multi stranded copper conductor , FRLS type cable drawn through and including PVC concealed conduit of 20mm in size complete with all accessories alongwith provn of 4 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire.

M & L for sub main wiring with two single core PVC insulated and unsheathed cable 6 sqmm with multi stranded copper conductor , FRLS type cable drawn through and including PVC concealed conduit of not less than 25mm in size complete with all accessories alongwith provn of 6 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire.(Three runs of cable and one run of conduit shall be measured as one length)

M & L for sub main wiring with four single core PVC insulated and unsheathed cable 10 sqmm with multi stranded copper conductor , FRLS type cable drawn through and including PVC concealed conduit of suitable size complete with all accessories alongwith provn of 2 run of 10 sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire.

Supply and Fixed single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of cap 20A complete all as specified and directed.

Taking down existing Ceiling fan/Exhaust fan capacity/type carefully and refixing the same with gutties, nuts boltss if required complete all as specified and directed.

Taking down existing Geyser any capacity/type carefully and refixing the same with replacement of PVC connection/Steel connection and anchor fastener pipe if required complete all as specified and directed.

M&L for earthing complete with GI steel earth plate electrod 60x60cmx6.00mm thick bouried directly in ground /earth pit not less than 2.25m deep below the ground level with top edge of the plate not less than 1.5 m below the normal ground level connected to test point by using GI wire of dia 4 mm as earthing lead soldering/revated to earth plate at one end and connected DB by means of nut, bolts etc complete with PCC pit (1:3:6) type GI cover with handle funnel with watering pipe wire mess GI protection pipe for earthing lead all complete as specified and as per electric plate No.5 of SSR Part I

KMTR MONCHER COLLECTION PRIVATE LIMITED (BID ID -3484266)

Sanjiv Kumar (BID ID -3484303)

NATIONAL BUILDERS (BID ID -3484028)

G S TRADERS (BID ID -3484341)

PAUL CONSTRUCTION CO. (BID ID -3483735)

M/S Kuldip Construction Co. (BID ID -3483564)

SARASWATI CONSTRUCTION CO (BID ID -3484322)