Construction of Degree College at Littipara in Pakur District under Sidhu Kanhu Murmu University, Dumka

Amount

Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.

Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item B)

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over area (exceeding 30cm depth 1.5m in width as well as 10 sqm on plan) including disposal of excavated earth lead upto 50m and lift upto 1.5M disposed earth to be levelled and neatly dressed - ordinary rock

Hard rock (blasting prohibited)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50Mand lift of 1.5M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)

Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).

Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).

Providing designation 75 A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.

Providing P.C.C.M - 150 with nominal mix of (1:2:4) in foundation with approved quality of stone metal grade III (50mm to 25mm size) clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing P.C.C.M - 100 with nominal mix of (1:3:6) in foundation with approved quality of stone metal grade III (50mm to 25mm size) clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 A brick work in C.M.(1 :6) in foundation & Plinth with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75 A brick work in C.M.(1 :6) in superstructure with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 125 mm thick reinforced designation 75 A brick work in C.M (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials , scafolding, raking out joints to 15 mm depth, curing, taxes and royalty ( but excluding the cost of reinforcement) all complete as per building specification and direction of E/l.

Extra for brick work for EACH consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.

Second floor

Head room /terrace floor

Providing R.C.C.M - 200 with nominal mix of (1:1.5:3) in foundation and plinth with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l.

Providing R.C.C.M - 200 with nominal mix of (1:1.5:3) in lintel with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l.

Providing R.C.C.M - 200 with nominal mix of (1:1.5:3) in band at lintel with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l.

Providing R.C.C.M - 200 with nominal mix of (1:1.5:3) in roof slab with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l.

Providing R.C.C.M - 200 with nominal mix of (1:1.5:3) in beam with approved quality of stone chips 20 mm to 6 mm size graded and clean coarse sand of F.M 2.5 to 3 including screening, centering, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l.

Providing R.C.C.M - 200 with nominal mix of (1:1.5:3) in columns with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including screening, shuttering, mixing cement concrete in mixer and placing in position, vibrating, striking, curing (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/l.

Providing av. 63mm thickR.C.C.M - 200 with nominal mix of (1:1.5:3) in chajja with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including making drip course in concrete, screening, centering, shuttering and mixing cement concrete in mixer and placing in position, vibrating, striking, 6mm cement plaster (1:4) in ceiling and sides of chajja with sand of F.M. 1.5 curing (but excluding the cost of reinforcement) taxes, and royalty all complete as per building specification and direction of E/l.

Providing R.C.C.M - 200 with nominal mix of (1:1.5:3) in stair case with approved quality of stone chips 20 mm to 6mm size graded and clean coarse sand of F M 2.5 to 3 including centering, shuttering, screening, mixing cement concrete in mixer placing in position, vibrating, striking, curing, taxes and royalty all complete as per building specification and direction of E/l

Providing 35mm thick precast RCC M-20 with nominal mix of (1:1.5:3) in shelves with approved quality of stone chips 12mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 with 1.5mm cement punning at top and side and 6mm cement plaster (1:4) at bottom including screening, curing and placing the slab in position (but excluding the cost of reinforcement) taxes and royalty all complete as per building specification and direction of E/I.

Providing 50mm thick precst RCC M-200 with nominal mix of (1:1.5:3) Jali with approved quality of stone chips 12mm and down well graded and clean coarse sand of F.M. 2.5 to 3 with 1.6mm thick M.S. wire as per approved drawing and design and placing the same in position true to plumb and level with 6mm dia M.S. rods placed at regular intervals both horizontally and vertically as required and properly grouted with the C.M. (1:3) including cost of curing, scaffolding and finishing all complete as per building specifications and direction of E/I.

Extra for RCC or PCC work for each consecutive floor above first floor complete as per direction of E/I

Second floor

Head room /terrace floor

Providing 25 mm thick damp proof course with cement concrete M-150 with nominal mix of (1:2:4) with approved quality of stone chips of 20 mm to 6mm size graded and clean coarse sand of F.M. 2.5 to 3 including, screening, shuttering and mixing cement concrete in mixer with 5% cico or any other approved water proofing compound and placing in position, striking, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing 1.5mm cement punning all cost complete Re. item no.8

Providing tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. Taking 8mm TMT FE 500 ( only valid for SAIL & TATA STEEL)

TMTC-500 8mm dia

TMTC-500 10mm dia

TMTC-500 12mm dia

TMTC-500 16mm dia

TMTC -500 20mm dia

TMTC -500 25mm dia

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with both sides decorative veneered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type non decorative single leaf flush door shutters in doors and windows with block board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneered of standard make with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing fully glazed steel door, winodws or ventilations of standard rolled 'Z' mullion steel sections and size as per IS - 1038 joints met and welded with 100X16X3mm M.S. lugs fixed in cement concrete (1:2:4) blocks 15X10X10cm, size including cost of oxidised iron fittings, with hinges, handle per steps, catch springs, 3mm thick plain glass panes with aluminium beads and inner frame fixed with lugs with 20mm long 6.3mm G.I. counter sunk machine screw and nuts and applying a coat of red lead paint carriage to work site hoisting and placing in postion in all storys and taxes all complete as per building specification and direction of E/I.

Providing & fixing pressed steel door frames manufactured from commercial mild steel sheet of 1.25mm thickness including hinges ,jamb, lock jamb, bead and if requiredangle threshold of mild steel angle section 50 X 25mm, orangle threshold of mild steel angle section 50 X 25mm, orbase ties of 1.25mm pressed mild steel welded or rigidlyfixed together by mechanical means, adjustable lugs withsplit end tail to each jamb including steel butt hinges split end tail to each jamb including steel butt hinges 2.5mm thick with mortar guards, lock strike-plate and 2.5mm thick with mortar guards, lock strike-plate andshock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by the Engineer Incharge - Profile - B - Fixing with adjustable lugs with split end tail to each jamb

Providing and fixing factory made P.V.C. door frame of size 50x47mm with a wall thickness of 5mm, made out of extruded 5mm rigid PVC foam sheet mitred at corners and joined with 2 Nos. of 150mm long brackets of 15x15mm M.S. square tube, the vertical door profiles to be reinfoorced with 19x19mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100mm size complete as per manufacturers specification and direction of Enginner-in-Charge.

30mm thick factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm . 19mm for styles and 15x15mm for top & bottom rails, M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle on eigher side forming styles: and 5 mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mmshall be tapered in 45 degree on the inner side to form top and bottom raiil and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail.

Top, bottom and lock rails shall be provided eigher side of the panel. 10mm (5mm x 2) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded / sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer's specificatio n& drawing (for W.C. and bathroom door shutter).

providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) tramsparent or dyed to required colour or shade with necessary screws etc. complete

Providing and fixing bright finished brass 100mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc. complete

Providing and fixing aluminium extruded section body tubular type universal huydraulic door closer (having brand log with ISI, IS:3564) embossed on the bodyu, door weight upto 36kg. To 80 kg. and door width from 701mm to 1000mm) with double speed adjustement with necessary accessories and screws etc. complete

Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete

Twin rubber stopper

Providing and fixing luminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transpoarent or dyed to required colour or shade with necessary screws etc. complete

Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or deyed to required colour or shade with nuts and screws etc. complete

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285 fixing with dash fasterners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required DPDM rubber/neoprene gasket etc., aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing/panelling C.P. brass/stainless steel screws, all complete as per architetural drawings and the directions of Engineer-in-charge (Glazing, panelling and dash fasteners to be paid for separately)

For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required inlcluding the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for separately) --- Polyester Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, windows, ventilators, shutters and partitions etc, with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer-in-charge (cost of aluminium snap beading shall be paid in basic item)

With float glass panes of 4mm thickness

With float glass panes of 8mm thickness

Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.

Steel work welded in built up sections/framed work including cutting hoisting fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing stainless steel (grade 304) railing made of Hollow tubes, channels, plates etc,. Including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessry stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasterners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasterners etc,.)

Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/l. (where material is not supplied by deptt.)

Providing 25mm thick first class patenet stone flooring (1:2:4) with stone chips in two layers bottom layer 19mm thick (1:2:4) with 12mm to 6mm sie graded stone chips and top layer 6mm thick (1:2) with 6mm down stone chips, in panels including cost of curing finishing the surface smooth by rubbing with carborandum stone taxes and royalty with all complete as per building specification and direction of E/I.

Providing and laying Vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorptions less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, laid on 20mm thick cement mortar (1:4) (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc, complete - size of tiles 600X600mm

Providing and laying Vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorptions less than 0.08% and conforming to IS:15622 of approved make in all colours and shades, in skirting, riser of steps, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS:15477, in average 6mm thickness, including grouting of joints

Providing and laying rectified glazed ceramic floor tiles 300x300m or more (thickness to be specified by manufacture) of 1st quality conforming to IS:15622 with approved make in colours white, ivory, grey, fume red, brown laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including pointing the joints with white cement and matching pigments, etc all complete.

Providing and fixing 18mm thick gang saw cut mirror polished (premoulded & prepolished) machine cut for kitchen platform and similar locations of required size of approved shade, colour and texture laid over 20 mm thick base of cement mortar 1:4 (1cement :4 coarse sand) laid and jointed with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edge to give high gloss finish etc. complete at all levels. Granite slab

Providing edge moulding to 18mm thick marble stone counters, vanities etc. including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-charge

Marble work

Granite work

Providing and laying 25mm thick kotah stone slab flooring of approved size, texture and colour over 19mm thick base of lime mortar (1:1:1) (1 lime putty sucrkhi coarse sand) laid over and jointed with grey cement slurry mixed with pigement to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I. - 600 X 600mm size

Providing and laying 15 to 23mm thick Kotah stone tiles in risers of steps, skirting and pillars of approved size, taxture and colour and over 12mm thick cement mortar (1:3) and joined with grey cement slury mixed with pigment to match the shade of the slab including rubbing to granolithic finish with approved quality of carborandum stone including cost of curing, txes and royalty all complete as per building specifiction and direction of E/I.

Providing and laying 60mm thick factory made cement concrete interlocking paver block of M-30 grde made by block making machine with strong vibratory compaction and of approved size and design/shape laid in required colour and pattern over and including 50mm thick compacted bed of course sand, filling the joints with coarse sand etc. all complete as per the durection of Engineer-in-charge.

Chequered precast cement concrete tiles 22mm thick in footpath & courtyard jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete on 20mm thick bed of cement mortar (1:4) (1 cement : 4 coarse sand) - Light shade pigment using white cement

Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direciton of E/l. a With "A" grade white 15 x 15 cm tiles.

Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.

Providing 25mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l. (design plaster)

Providing & laying water proofing treatment in sunken portion of WCs, bathrooms etc. by applying cement slurry mixed with Armourcrete of M/S The Structural Water Proofing Company PVT. Ltd.or Tapecrete of M/s CICO Engg. Servce consisting of applying :

(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with Armourcrete or Tapecrete @ 0.125 kg/ sq.m. This layer will be allowed to air cure for 4 hours

(b)second layer of slurry of cement @ 0.242 kg/sqm mixed with Armourcrete or Tapecrete @ 0.126 kg/ sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.

The rate includes preperation of surface, treatment& sealing of all joints, corners, junctions of pipes & masonary with polymer mixed slurry.

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc. consisting of following operations. a. Applying and grouting a slurry coat of neat cement using 2.75kg/Sq.m. of cement admixed with ;proprietary water proofing compound confirming to IS 2645 over the RCC slab including cleaning the surface before treatment.

.b.Laying cement concrete using broken bricks/brick bats 25mm to 100mm size with 50% of cement mortar (1 cement : 5 coarse sand) admixed with proprietary water proofingcompound confirming to IS 2645 over 20mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with proprietary water proofing compound confirming to IS 2645 to required slope and treating similarlythe adjoining walls upto 300mm height including roundingof junctions of walls and slabs.

C. After two days of proper curing applying a second coat of cement slurry admixed with proprietary water proofing compound confirming to IS 2645 and approved by Engineer-incharge d. Finishing the surface with 20mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with properietary water proofing compound conforming to IS:2645 and approved by Engineer-incharge including laying glass fibre cloth of approved quality in top layer plaster and finally finishing the surface with trowel with neat cement slurry and making of 300X300mm square 3mm deep.

e. The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test. All above operations to be done in order and as direted and specificed by the Engineer-in-charge. With average thickness of 120mm and minimum thickness at khurra as 65mm

Providing and fixing structural glazing to fixed panels/part openable with 6mm thick glass and green colour, reflective low-e-toughened glass of Glaverbel/Saint-Gobain make with noaluminium section exposed to outside and only glass panels with silicon joints visible from outside . The system specially designed with aluminium section of grade 63400WP IS:733 and IS:1285 electr colour anodized/pure polyster powder coated in approved shade and colour with mullion fixed to beams/columns through adequately designed M.S. painted anchor brackets and expansion fasteners as required. the designed to be as per BIS code fro required wind pressure IS:875 part III and use of aluminium section alloy as per IS:8147. System designed to strictly consider for thermal moments, air infiltration water penetration, seismic movement and structural movement. Silicon sealant structural grade and weathering grade shall be "Dow corning - USA" or "Wicker-Germany" as per the designed requirement. Natural cure with good U.V. resistance to be used. the above frames should be fixed to the concrete/masonary walls and floor by means of self expanding screws

Providign and applying Plaster of Paris Putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing two coats of oil bound distemper ofapproved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete

Finishing walls with premium acrylic smooth exterior paint with sillicone additives of requited shade . New work : 2 or more coats applied @1.43 Ltr/10sqm over and including base coat of waterproofing cement paint applied @2.2 Kg/10 sqm

Providing two coats of snowcem of approved shade and make over a coat of cement primer on new surface including preparing the plastered surface smooth with sand paper scaffolding curing and taxes all completee as per building specification and direction of E/I.

Providing textured polymer based textured finish of approved shade on walls with synthetic resin bounded granules spectrum or similar approved as per manufacturer's specification including necessary scaffolding etc. all complete as per direction of E/I. (Heritage)

Providing French spirit polishing over new wooden surface to give desired texture and gloss with approved make and shade of ready mixed French polish including cleaning the surface after removing dirt, scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specifcation and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing 250 mm wide BRICK DRAIN in cement mortar (1:6) with avarage 150mm. Clear depth and 250 mm apron including cost of earthwork involved with 75m cement concrete (1:4:3) over one brick designation 75A, flat soling in proper grade and slope at the base , the drain dully plastered in C.M.(1:3) with puning over exposed surface all complete as per building specification and direction of E/I.

Making plinth protection with bricks of class designation 75 laid on edge in cement mortar 1:6 (1cement :6 coarse sand) with 12mm th. Bed of cement mortar 1:6 (1cemnt:6 coarse sand) over 75mm bed of dry brick aggregate 40 mm nominal size rammed, consolidated and grouted with fine sand and the top of bricks pointed with cement mortar 1:3(1cement :3 fine sand).

Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia

Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Bend 87.5 degree

Shoe (Plain)

110mm shoe

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less thaN 440 grams.

Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means 50X50X50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete - 110mm

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25 of size 1000X450X50mm reinforced with 8mm dia four nos longitudinal & 9 nos. cross sectional TMT hoop bars, including providing 50mm dia perforations @ 100 to 125mm c/c. including providing edge binding with M.S. flats of size 50mm X 1.6mm complete all as per direction of E/I.

Supplying, filling, spreading & levelling stone boulders of size range 5cm to 20c, in recharge pit in the required thickness for all leads & lifts all complete as per direction of Engineer-incharge

Supplying, filling spreading & levelling gravels of size range 5mm to 10mm in the recharge pit over the existing layer of boulders in required thickness for all leads and lifts all complete as per direction of E/i.

Supply, assembling, lowering and fixing in vertical position in borewell/recharge pit unplasticized PVC medium well casing (CM) pipe of required dia conforming to IS : 12818 including required hire and labour charges, fittings & accessories etc. all complete for all depths as per direction of Engineer-in-charge

150mm nominal size dia

Costs of drilling 200mmX165mmX125mtr. Deep borewell in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH rig machine, all complete including supplying all materials, tools, drilling rig, Air compressor and equipments, as well as fuel lubricants and cost of transportation of rig machine and other vehicles upto the site

From 0-50 mtr.

Providing and fixing concertina coil fencingwithpunchedtapeconcertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tiedwith G.I. staples and G.I. clips to retain horizontal, includingnecessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge,with reinforced barbed tape(R.B.T.) / Spring core (2.5mmthick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Angle size 50x50x6 in mm as per I.S. 226

Providing and fixing ball plug/bottom plug of required dia to the bottom of pipe assembly of tubewell/recharge pit as per IS:2800(part 1) 150mm dia

Providing & injecting chemical emulsion for pre-construction Anti-termite treatment and creating a chemical barrier under and all around the coloum pits,wall treanches,basement excavation, top surface of plinth filling,junctions of wall and floor along the external perimeter of building with approved chemical as per IS code As per specification and direction of E/I.

Supplying C.I. Cover 600X450MM (Wt. 25 kg) - 4 nos.

(JSR basic rate 1745 + 10% CP) Pge 42 it.no.26(b)

CARRIAGE OF MATERIALS

Bricks (8 KM.)

Coarse Sand ( 10 KM.)

Stone Chips (22 KM.)

Stone Metal (20 KM.)

Earth (3 km)

INTERNAL ELETRICAL

Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.

Supply and Fixing Light Plug Point with Modular Type Accessories: Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.

Supply and Fixing Light Plug Point with Modular Type Accessories: Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.

Supply & fixing 20A SPN MCB Industrial Socket Outlet: Supply and fixing of 20A, 240V, SPN insustrial type socket outlet with 2 poles and earth, metal enclosed plug top along with 20 amps 'C' series, SP MCCB, in sheet steel enclosure, on surface or in recess with chained metal cover for socket out let and complete with connections, testing and commissioning etc as required.

Power Plug Wiring in PVC conduit (2x4 sq. mm): Wiring for light/power plug with 2x4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit along with 1 number 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sqmm + 1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sq mm earth wire

2x4 Sqmm + 1x4 sq mm earth wire

4x6 Sq.mm + 2x6 Sq.mm earth wire.

4x16 Sq.mm + 2x16 Sq.mm earth wire.

S/F TP MCB DB:- Supplying and fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (Without MCB/RCCB/ISOLATOR). (All TP MCB DB shall be as per IS:8623)

4 Ways (4+12 ways) double door

6 Ways (4+18 ways) double door

8 Ways (4+24 ways) double door

S/F 'C' series MCB:- Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32A Single Pole

6/32A TPN MCB

63A TPN MCB

S/F Ceiling Rose: Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.

S/F Batten / Angle Holder: Supplying and fixing batten / angle holder including connection etc as required.

ITC fluorescent fitting directly on surface :- installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, directly on ceiling / wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper cond.

ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required.

S/F Modular type electronic fan regulator: Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

Telephone Wiring in Existing Conduit: Supplying and drawing, following pair, 0.5 sq.mm FR PVC insulated copper conductor, unarmoured telephone cable in the existing surface / recessed steel / PVC conduit as required.

S/F Modular type Switch / Socket: Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required.

Telephone socket outlet

LIGHT FITTINGS

Supply of surface/ pendent mounted fluorscent tube light luminaries with 1x28W Tube light with all accessories as per the standard Catlogue Items. (Make :- Philips - TMS122M-TL-5-1X28WEBE/ Bajaj-BITR128/Wipro WIF 20128 / Havells-LHFYBYF1ON1W028. or equivalent

Supply of Special type bulk head fittings complete set with 60W lamp. (Make- Havells LHKL01160099 with 60W GLS Lamp / Philips NXC101 1xA60-60W / Bajaj-BJDB 100ES) of equivalent

Supplying, fitting and fixing fancy wall bracket of anodised aouminium 12mm diameter pipe fixed on 3mm thick M.S. pointed plate of size 170mm x 40mm with brass bracket holder incouding fitting CFL lamp as required

Supplying, fitting and fixing 250 Watt HPSV lamp with complete set with choke lamp etc. as required with G.I.bracket for mounting of sodium vapors light as per directionof E/I. Including connection etc. all cost complete

Providing, fitting, fixing & testing of (Esential) CFL Lamp 18/20W CFL in existing battan / angle holder. (Make :- Philips / Bajaj / Crompton / Wipro)

Supplying and fixing flush type circular ceiling fitting complete with holder, aluminium anodized back plate and glass globeincluding connection etc. as required

Supply of 300mm dia 1400 rpm,230V AC Exhaust Fan (metal) exhaust fan in with double ball bearing existing opening and fittinigs as required. ( Make:-Havells-Model-Turbo Force-1400rpm / Bajaj-Item Code-70059 / Equivalent in Crompton Greaves) .

Supply of energy efficient 1400mm sweep ceiling fans complete with double ball bearing, motor, blades, downrod, canopies, capacitor, suitable for operation on 230 volts, 50 Hz., 1 phase, AC supply connection with 1.5 sq.mm PVC Copper wire complete as required (minimum three star rated with euro effect fan shall be provided or approved by engineer incharge) Make- Havells, Bajaj/ Crompoton

GI Earth Pipe Electrode: Earthing with G.I. earth pipe 4.5 mtr long , 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. (but without charcol or coke and salt) complete as required.

Salt/ charcoal for Pipe Earth Electrode: Extra for using salt and charcoal for pipe earth electrode as required.

Providing and Fixing 25mm x 5 mm GI Earth Strip in Ground: Providing & fixing of 25mm x 5mm GI Strip at 0.5 metre below ground as strip earth electrode, including soldering etc as required.

Providing and Fixing 25mm x 5 mm GI Earth Strip in Pipe: Providing & fixing of 25mmX5mm GI Strip for Fixing in GI Pipe from earth electrode as required.

Provioding and laying 1.1 KV grade aluminium armoured cable as per IS 1554 (Part I) heavy duty all cost complete including cost of brass compression gland, cable jointing and end termination as per specification and direction f E/I.

3.5 core, 185 sq.mm

3.5 core, 95 sq.mm

3.5 core, 50 sq.mm

3.5 core, 35 sq.mm

Fabrication, assembling 200A HRC TPN switch incoming and 100/63A TPN, 35KA MCCB outgoing 4 nos. lighting LT electrical sub distribution control panel with the foloowing accessoires:

Fabrication, assembling, 630A , 4 pole MCCB incoming and 200A, 12 nos. 4 pole MCCB outgoing lighting LT electrical main distribution control panel with the following accessories:

Providing and fixing of lighting conductor finial made of 25mm dia. 300mm long G.I. Tube having three copper prongs at top with 85mm dia. 6mm th. G.I. Base plate including holes etc. complete as required with providing and fixing copper tape 20mm X 3mm on parapet or wall as required, providing and fixing one no. testing joints made of 20mm X 3mmX 125mm G.I. Strips with 4 nos. G.I. Bolts, nut checknut spring washer etc. as required all complete as per relevent IS code and direction of E/I.

GENERATOR SET 125 KVA

Providing, Installing, Testing and Commissioning of 'Silent Type' Diesel Generating set alongwith having Prime Power Rating suitable to drive of 125 KVA, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase system generator & for 0.85 Load Factor and consisting of the followings:- (Make- Kirloskar Green/Jakson/Sterling & Wilson Power Gen Pvt. Ltd with MTU Engine or equivalent ).

Diesel Engine

Diesel Engine 4 stroke Water/ liquid Cooled with radiator type, electric start of suitable BHP at 1500 RPM suitable for above output of alternator at 45 Degree C, 50% RH & at 1000 Meter MSL and Conforming to BS 5514, BS 649, IS 10000, capable of taking 10% over loading for one hour after 12 hours of continuous operation. The engine will be fitted complete with all the required accessories.

Engine mounted Instrument Panel fitted with and having digital display for following:

Start-stop switch with key

Lubrication oil pressure indication

Lubrication oil temperature indication

Battery charging indication

RPM indication

Over speed indication

Low lub. Oil trip indication

Engine Hours indication

Alternator

Synchronous alternator rated at 125 KVA, 415 VOLTS AT 1500 RPM, 3 PHASE 50 Hz, ACsupply with 0.8 lagging power factor at 45 Degree C, 50% RH & at 1000 Meter MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty, self-excited and self- regulated through AVR conforming to IS : 4722/BS 2613 suitable for tropical conditions and with class F/H insulation.

Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary reinforcement which shall be installed on suitable cement concrete foundation and vibration isolation arrangement as per recommendations of manufacturer. The above 125 KVA Silent DG set costing is inclusive of construction of 150mm thich 12ftX8ft RCC foundation as DG Platform.

Fuel Tank

Daily service fuel tank of minimum 650 liters capacity fabricated out of 3 mm thick M.S. sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS class 'C' pipes of suitable dia. Complete with valves, level indications & accessories as required as per specifications.

Exhaust System :

Dry exhaust mainfold with hospital exhaust silencer and catalytic convertor

Starting System

12 V/24 V DC starting system comprising of starter motors: voltage regulator and arrangement for initial excitation complete with suitable nos. of batteries (25 plates, 180 Amp. Hour capacity lead acid type) as required as per specifications

Acoustic and weather proof enclosure with arrangement for fresh air intake for cooling of the engine & alternator, extraction, discharging hot air in to the atmosphere as per specifications.

1 No.additional wall mount 160A , 440V, TPN change over along with enclosure has to be provided for fire pump to connect main fire pump with DG supply.

3 Sets of current transformers 15 P 10 accuracy for protection and 15 VA class-I for meetering

Energy analyser unit to indicate current voltage frequency power factor and KWH

Indicating lamps for load on mains and load on set

Fuse for instruments

Main supply failure monitor

Supply failure timer

Restoration timer

Control unit with three impulse automatic engine start/stop and failure to start lockout

Impulse counter with locking and reset facility

Necessary Electro Mechanical Interlocking for not to parallel both supplies

ON/OFF/Control circuit switch with indicator

Audio/Video annunciation for

High Water temperature

Low lubricating oil pressure

Engine Over Speed

Engine fails to start

Full load/maximum load warning

PLUMBING AND SANITATION WORK

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (A) With "P" trap (b)12.5 lit. low level P.V.C. cistern

Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry hindustan or any other ISS approved make with 100mm HCI p trap 15 litres CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings CI or C C bracket 32mm alkethene / PVC telescopic flush pipe about 2m long with one brass coupling and clamps GI chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be fixed in floor 15mm CI body brass spindle stop cock of weight not less than 50 grames 15mm PVC connection pipe 450mm long and coat of red oxide primer etc all complete as per specification and direction of E/I.

(A) 580 mm long

with 12.5 litre low level PVC cistern

Supplying, fitting and fixing flat back or angular lipped front vitreous white glazed earthern ware urinal of Hindustan "Parry" or any other approved ISS make with 5 ltrs. Capacity C.I. automatic fushing cistern of reliance for any other ISS approved make with all fittings with C.I. or RS brackets standard size G.I. flush pipe with fitting clamps 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 gms. 15mm PVC alkethene pipe 450mm long with brass coupling at both ends and doing plumber points including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor making good the same etc. all complete as per speciifcification and direction of E/I. Flat back or standing corner (600X350mm)

Providing and fixing one piece construction white vitreous china squatting plate with an integral logitudinal flushing pipe white PVC automatic flushing cistern with fittings, standard size G.I./PVC flush pipe for back and front flush with standard spreader pipes with fittings, G.I. glamps and C.P. brass coupling complete, including painting of fittings and cutting and making good the walls and floors etc. wherever required

supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or hindustan or any other I.S.S approved make supported on painted C.I OR R.S bracket 32mm C.I brass waste 15mm dia C.I body brass spindle stop cock of approved quality of weight not less than 350 grames, 32mm PVC wate pipe 750mm long with brass coupling with one end and making plumber joints etc.all complete as per specification and direction of E/I.

Supplying, fitting and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I.

20mm dia.

25mm dia.

32mm dia

40mm dia

Providing and fixing brass stop cock of approved quality all complete as per specification and direction of E/I. … 15mm dia.

Cutting chajjas or concrete for laying PVC Pipe and restoring the same with R.C.C. (1:2:4) brick work in cement Mortar (1:4) and cement plaster 1:4 as per specifiction and direction of E/I

Making holes in walls for PVC Pipe and restoring the same atfer pipe Laying (b) 250mm thick wall

Cutting drain width wise above GL for laying PVC pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in C.M. (1:4) with neat cement punning as per specifciation and direction of E/I. (PVC 110mm dia)

Making holes in wall for laying PVC pipes and restoring the same all cost complete (PVC pipe 250mm dia)

Supplying all tolls and labour and cutting chajja cornice for laying PVC pipes and making good the same as per specification and direction of E/I.

Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E/I. (all rates have been adopted from the basic rate from SOR + 30% for labour and Contractors profit)

Pillar cock (long neck) (Basic rate Rs.756.60 + 30% for C.P. & laying charge)

Bib cock - long thread (Basic rate Rs.701.10 + 30% for C.P. & laying charge)

Angular stop cock L.T.(Basic rate Rs.572.85 + 30% for C.P. & laying charge)

4 way diverter for concealed fittings (Basic rate Rs.1911.80 + 30% for C.P. & laying charge

Glass shelf (Basic rate Rs.641.25 + 30% for C.P. & laying charge

Flush valve complete with 32mm size control cock & flange (Basic rate Rs.3283.20 + 30% for C.P. & laying charge

32mm dia. PVC waste pipe 750mm long with cushion (Basic rate Rs.52.00 + 30% for C.P. & laying charge

15mm C.P. nipple with coupling(As per JSR 15 basic rate Rs.72.70 + 30% C.P. & laying charge)

Steel jali - 100mm dia. (Basic rate Rs.40.20 + 30% for C.P. & laying charge

Providing Solvent cement (as per JSR 15 basic item - 228.55 + 30% C.P & laying charge

Supplying, fitting and fixing Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. 600 X 450mm

Supplying, fitting and fixing C.P. brass towel rail 20mm X 600mm with bracket container

Supplying, fitting and fixing C.P. brass soap dish container medium quality with screw and hinges etc.

Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of engineer in charge

Supplying, materials and labour for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS 8931, 15mm dia nominal bore of approved brand C.P. fittings

Providing and fitting C.P. brass angle vale basin mixer and geyer points of approved qulity confirming to IS 8931 15mm nom inal bore approved brand C.P. fittings

Providing and fixing PTMT extension nipple 15mm size with 12" BSP thread 70mm length and 30mm breadth and weighing not less than 18gms of approved make

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e fixing the pipe with clamps at 1Mtr. Spacing. This includes jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the walls etc.

20mm nominal bore

25mm nominal bore

32mm nominal bore

External work - 40mm nominal bore

External work - 50mm nominal bore

Providing & fixing on wall face unplasticised - Rigid P.V.C. pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia

Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

Single Tee with door

Bend 87.5 degree

110 mm bend

Providing and placing on terrace (at all floor levels) (PVC) Polyethylene water storage tank ISI 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Making soak pit 2.5M diameter 3 mtr. deep with 45X45cm dry brick honey comb shaft with brciks of class designation 75 and S.W. drain pipe 100mm diamter 1.8 mtr. long complete as per standard design with FPS bricks

NON SCHEDULED ITEMS

Supplying and fixing PVC fittings of approved make confirming to IS : 1729 including supplying nails and bobbins, fixing solutions including earth work or masonary work cutting and remaking and providilding as the case may be all complete as per specification and direction of E/I.

PVC plain bend 100mm dia.

PVC double junction with door and ear 100mm dia.

PVC cowl - 100mm dia.

Floor trap - 100mm dia.

Ring rubber

Lubricant

Door piece

2 NOS BORE WELL WITH PUMP FOR EACH SITE

Costs of drilling 200mmX165mmX125mtr. Deep borewell in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH rig machine, all complete including supplying all materials, tools, drilling rig, Air compressor and equipments, as well as fuel lubricants and cost of transportation of rig machine and other vehicles upto the site

From 0-50 mtr.

Above 51 mtr.

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia conforming to IS : 12818, including required hire and labour charges fittings & accessories etc. all complete for all depths, as per direction of Engineer-in-charge - 200mm nominal size dia

Gravel packing in tube well construction in accordance with IS : 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge

Development of tube well in accordance with IS 2800 (part 1) and IS: 11189 to establish maximum rate of usable water yield without sand content (beyond permissible limit) with required capacity air compressor, running the compressor for required tile till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, colleting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete including hire & labour charges of air compressor, tools & accessoires etc. all as per requirement and direction of Engineer-in-charge.

Providing & fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe, removable as per requirement, all complete for borewell of 200mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS:2800 (Part-1) including necessary bolts & nuts of required size complete

Providing and fixing bail plug/bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS :2800 (Part-1) 200mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pioes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement trenching, refilling & testing of joints complete as per direction of Engineer in charge

50mm nominal outer dia pipes

Supplying 150mm dia submersible pumps sets confirming to IS:8034 and motor confirming to IS:9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller, motor suitable for working on 415V+10%, 3PH. 50HZ, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. the pump set shal be suitable for direct couplings, pump shall have suitable outlet as per manufacture design. Anti thrust stream lined non return valve shall be provided with pump. 3 mtr. submrsible copper conductor cable in single/double run shall be provided with each pump.

Submersible pump set 100mm dia (with polypropylene/noryl impeller) upto 20 stage - 3.0 HP

Transformar and external lighting

Copper Earth Plate Elecrode:- Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or cock and salt) complete etc. as required. DG=2 nos + Transformer=2 nos).

Extra Salt & Charcoal for Copper Earth Plate Elecrode:- Providing and fixing salt and charcoal or cock for copper earth plate elecrode complete etc as required.

Providing and Fixing 25mm x 6mm GI Earth Strip in Ground: Providing & fixing of 25mmX 6mm GI Strip at 0.5 metre below ground as strip earth electrode, including soldering etc as required.

P/F 25 x 5mm copper earth strip in pipe:- Providing and fixing 25mmx5mm cpper earth strip in 40mm & 4.5Mtr long G.I.pipe for earth electrode etc. as required.

1.1 kV POWER CABLE

Supply & Erection of 3CX2.5 Sq. Cu. Flexible Wire for connection of light fitting.

Supply & laying of following XLPE insulated armoured cable of 1.1 KV grade,

4CX10 sq. mm armoured AL Cable.-for street light

3.5 Core 120 Sq mm for power supply fromTransformer to Main panel (2 run)

CABLE LAYING

HT Cable Laying up to 120 sq. mm. in Ground :- Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size exceeding 25 sq.mm. but not exceeding 120 sq.mm. direct in ground including excavation, sand filling, protective covering and refilling the trench etc as required.

MV Cable Laying up to 25 sq. mm. in Ground :- Laying of one number PVC insulated and PVC Sheathed / XLPE power cable of 1.1 KV grade of size not exceeding 25 sq.mm. direct in ground including excavation, sand filling, protective covering and refilling the trench etc as required.

CABLE JOINTING AND JOINT KIT

Supply, making, and termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed/ XLPE aluminium cable of 1.1 kV grade as required.

4CX10 sq. mm armoured AL Cable.(25mm)

3.5 Core 120 Sq mm armoured AL

Bihar Schedule Rate 2016

Supply and erection of of 6 M height hot dip galvanised octagonal pole with with following arm , top dia 70mm and bttom dia bottom 130 mm A/F & 70 mm A/F across top made up of 3 mm thk HT sheet alongwith base plate of size 220X220X12 mm thick , shall door opening for junction box mounting and suitable size bolts with template and all complete,

Single arm 1500mm

Double arm 1500mm

Supply and fixing of 90W LED street light fitting ,with die cast aluminium housing of ingress protection of IP65 and complete with all accessories etc on pole including connection and earthing the body etc as required. Make- Bajaj/ Philips/ Havells.

Erection of metalic Pole of following length in cement concrete 1:3:6 ( 1 cement:3 coarse sand : 6 graded stone aggregate 40mm nominal size) foundation including excavation and refilling etc as required.

above 4.5 metre and upto 6.5 metre

Providing and laying in position cement concrete 1:2:4 ( 1 cement:2 coarse sand : 4 graded stone aggregate 40mm nominal size) foundation of DG set including form work etc as required.

Market Rate

LED Post top of 40W Arian : Supply and fitting of LED post top made in cast aluminium spigot housing with decorative clear opal acrylic diffuser IP65 protection. Model BGCT W4 40W LED WW of Bajaj or equivalent)

HT Cable( for Transformer) : 3 core 50 sq.mm, HT XLPE cable, aluminium conductor, conductor screen with extruded semi conducting compund, XLPE insulated, insulation screening with extruded semi conducting compund in combination with copper tape, cores laid up, innersheath of PVC tape, glavinised flat steel strip armoured and overall PVC sheathed cable confirming to IS 7098.

Supply out door type copper wound transformer continuosuly rated for 3 PH ,50 Hz at full load and temp. rise not exceeding 45 degree thermometer in oil and 50 degree c by the resisitance in winding after continuous run at full load rating the tranfformer should have oil immersed winding having vector group DY11, HT side connected in delta and Lt side connected in stra with netural brought out connected to provide seperate earthing . The Transformer shall have power terminal arrangement bushing /cable end box on HT side and cable end box on LT side . 2 nos channels with stopper shall be provided and fixes on the provided plinth for mounting the transformer should have following standered fittings . The Transformer shall be latest manufacturing standered as per amended is specification and l;oad and No load losses shal be lilmited to the values given below or as per IS or Norms issiued by MSEDC Ltd / JSEB which ever area lower

Oil consevator with filling hole with cap and plain oil level gauge .

Silica gel dehydrating breather charged with silica gel

Oil drain valve

Oil filter valve

Lifting Eyes /hooks

Two earthing terminals

Diagram and rating plate

Air vent

Explosion vent

100 mm dia thermo meter with thermometer pocket

Four bi directional plain roller

Power Transformer 11000/433 volts with off load tap charger 12.5% to +2.5% in step of 2.5%

400 KVA (No load loss 715w and load loss 5000w)

Fabrication, assembling 200A HRC TPN switch incoming and 100/63A TPN, 35KA MCCB outgoing 4 nos. lighting LT electrical sub distribution control panel with the following accessories:

Fabrication, assembling, 630A , 4 pole MCCB incoming and 200A, 12 nos. 4 pole MCCB outgoing lighting LT electrical main distribution control panel with the following accessories:

FIRE PUMP ROOM EQUIPMENT

Control Panel for Fire pumps

Fabricating & Supply, installing, testing and commissioning of compartmentalized common control panel for Electrical motor driven pumps.

1100 V GRADE POWER / CONTROL CABLES

Supplying, laying, testing & commissioning of FRLS,PVC outer sheath, steel armored, copper conductor, 1100v grade power cables with glands etc.The cables shall be laid in tray / in trenches/on walls/ floor etc. as required.

CABLE TRAY

Supplying and fixing of perforated G.I.sheet cable tray with necessary angle iron suspension supports, anchor fasteners etc. complete. Maximum height of suspension shall not exceed 500 mm.Size of the tray shall be suitable for laying the above mentioned cables.

G.I. Earth strips of 50mm x 6mm thick, strip shall be run on floor / ceiling / walls, from the equipment to the nearest Earth pit with with necessary accessories as required. ( Erath pit shall be executed by other agencies).

150mm nominal dia

65mm nominal dia (Heavy)

150mm nominal dia

80mm nominal dia

50mm nominal dia

Supplying, installing, testing and commissioning of C.I. Non-return valves as per IS: 5312(PN 1.6) swing check type with required flanges, nuts, bolts and gaskets etc. complete.

150 mm nominal dia

50 mm nominal dia

Supplying, Installing, testing and commissioning CI butterfly valves as per BS 5155 (PN 1.6) slim seal standard lever operated type with required flanges, nuts, bolts etc. complete.

150mm nominal dia

50mm nominal dia

Supply, Erection, Testing and commissioning of C.I.Gate valves as per IS: 14846 (PN 1.0 Rating, for suction side of the pumps) and Non rising spindle type with flanges,bolts, nuts, washers, gaskets etc.

150mm nominal dia

65mm nominal dia

Supply, Erection, Testing and commissioning of Suction Strainer with flanges, bolts, nuts, washers, gaskets etc.

200mm nominal dia

Supply and installation of Pressure switches of suitable range for pump sets with Ball valves, Fittings like unions / collars / reducers etc.

Supply and installation of Pressure gauges of suitable range for pump sets with Ball valves, siphon, Fittings like unions / collars / reducers etc.

HYDRANT SYSTEM

Supplying, installing, testing and commissioning of M.S. Pipes confirming to IS 1239/3589, Heavy grade with suitable type of supports, malleable specials such as Reducers, Tees, elbows, flanges. Including cutting,Welding as per drawings. The rate quoted should be included with anticorrosive treatment with 4 mm thick "PYPKOTE" polymer corrosion resistant tape as per IS 10221, overlap shall be 15mm minimum.

150mm nominal dia

80mm nominal dia

Supply, Erection, Testing and commissioning of C.I.Gate valves as per IS: 14846 (PN 1.6 Rating) and Non rising spindle type with flanges,bolts, nuts, washers, gaskets etc.

150mm nominal dia

Supplying, Installation,Testing and commissioning of Hydrant valve comprising of the following in the Fire duct;

Single headed hydrant valve as per IS 5290, made of gunmetal with 63 mm dia instantaneous outlet of 80 mm dia fanged inlet ,Blank caps , chain and hand wheels etc complete.

30 M long, 63mm dia RRL hose with instantaneous couplings and Hoses shall be stored in side the hose cabinet.

1 no. Gun metal short branch pipe with nozzle.

Supplying and fixing approved make 25mm dia. Air release safety valve with unions,ball valve etc. complete.

Supplying, installing, testing and commissioning of Gun metal chrome finished Ball valves with fittings of screwed end type.

50mm dia.

FIRE EXTINGUISHERS

Supplying, installing and commissioning Portable Fire extinguishers of following type & capacity.

Carbon-di- oxide type fire extinguisher of 4.5 kgs. Capacity, CO2 gas filled in brand new seamless cylinder with powder coated finish, made out of Manganese steel, with wheel type valve, discharge nozzle, bend & horn,wall mounting bracket etc. complete, confirming to IS: 15683

Mechanical Foam type fire extinguisher 9Lts. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union, high pressure CO2 gas cartridge hose and ABS type branch pipe and wall mounting bracket etc complete, confirming to IS: 15683

Dry chemical powder type fire extinguisher of 5 / 6 Kgs. Capacity, with initial filling in brand new cylinder with powder coated finish, fitted with Gun metal union,high pressure CO2 gas cartridge, discharge hose, wall mounting bracket etc. complete, confirming to IS:15683

Water CO2 type fire extinguisher 9 lts. Capacity, initial filling in brand new cylinder of powder coated finish, fitted with Gun metal union, high pressure CO2 gas cartridge & wall mounting bracket etc. complete confirming to IS: 15683

SIGNAGES

Providing and installing in position the following type of AUTOGLO Photoluminescent Signages complete with fasteners

Signage with printed “EXIT"( Model : D29/D30 , Size :150mmX200mm)

Floor identification signage ( i.e., 1/2/3 …etc.) Size 225mm x 225 mm at each stair enclosure on every floor

Fire Alarm System

Supplying, installing and commissioning of Manual call point with . cabinet of suitable size with mounting supports etc. complete.

Supplying, installing and commissioning of Electronic Hooter cum sounder with M.S. cabinet of suitable size with mounting supports etc. complete.

Supplying, installing and commissioning of 2 x 1.5 Core Cable with conduit wiring

Supplying, installing Furniture and Funrnishing item to be used make godrez ,durian etc. and equivelnt .

Bench Cum Desk

Big Table 104

Bravo H.B

Bravo Visitor H.B

Chair Bravo H.B

Computer

EXECUTIVE TABLE ARRIVE WITH HALO CHAIR

GLASS DOOR STORWEL

HALO VISITOR CHAIR

MILAN SOFA SET WITH BLOOM TEA TABLE

PROJECTOR

RECEPTION TABLE (2ARC)

SINGLE BED (ESCA)

STORWEL PLAIN

Table 9

13 PASSENGER LIFT

Providing and Installing, Testing & Commissioning of 13 Passenger automatic Lift - 1no., including one year free maintenance which will be start from handing over the lift, all taxes and all complete as per following detail specifications. APPROVED BRAND - OTIS/ KONE.

PRODUCT- GeN2- Nova

DETAIL- GeN2- Nova VXN

CAPACITY(Kgs) - 884 kg 13 persons.

SPEED(mps) - 1mps.

RISE (M) - 19.5 M

STOPS - 6 Stops with (all opening on the same side)

CONTROLLER TYPE - ACD3-MR

DRIVE - VF Regenerative (closed loop)

POWER SUPPLY - 400/415 Volts (3 phase AC)

OPERATION - Full collective operation.

CAR GROUP - One car (simplex)

MACHINE - PM Gearless (Located above shaft)

TRACTION MEDIA - Flat Coated Steel Belt.

CAR FINISH -

Rear Mid Panel= Stainless Steel # 4 (Hairline)

Rear Corner Panel= Stainless Steel # 4 (Hairline)

Side Panel= Stainless Steel # 4 (Hairline)

Front Panel= Stainless Steel # 4 (Hairline)

FALSE CEILING TYPE - CD-41

FALSE CEILING FINISH - Stainless Steel # 4 (Hairline)

VENTILLATION - Cross flow fan.

HAND RAILS - Stainless Steel Mirror Finish Handrails on all car panel. (sideLH, sideRH& Rear)

FLOORING - Vinyl Tiles

CAR DOOR FINISH - Stainless Steel # 4 (Hairline)

LANDING DOOR FINISH - Stainless Steel # 4 (Hairline)

FIRE RATED DOORS - Fire rating-60 mins

PIT DEPTH - 1350

OVER HEAD - 4200

HOISTWAY DIMENSIONS(WXDXH-MM)- 2100 mm W x 1700 mm D

CAR DIMENSIONS (WXDXH-MM)- 1600 mm W x 1350 mm D x 2300 mm H

CAR & HOISTWAY DOOR TYPE- Central opening (CO) doors

DOOR OPENING (W x H- MM )- 900mm W x 2100mm H

DOOR OPERATOR- DC Door Operator

COP- Gien Buttons in Stainless Steel #4 (Hairline)

CAR POSITION INDICATOR- Dot matrix (Red Led) Scrolling Display

HALL FIXTURES- O2000

HALL FIXTURES FACE PLATE- Stainless Steel #4(Hairline)

HALL BUTTON ARRANGEMENT- HALL Button with HPL

STANDARD FEATURES- Anti-nuisance Car Call Protection, Independent Service (for duplex only) Overload Device, Nudging, Emergency Firemen's Service, Emergency Car Light Unit, Infrared Curtain Door Protection, Door Time Protection, Emergency Alarm Button,Extra Door Time of Lobby & parking, Door Open/Close Button, Manual Rescue Operation, Belt Inspection Drive, Auto Fan Cut Off.

OPTIONS INCLUDED- Automatic Rescue operation.

Add 12% GST

Add 1% Labour Cess

M/S PRASAD ASSOCIATES

M/S PARAS NATH SINGH

Excel Venture Construction (P) Ltd.

SARYUG GAUTAM CONSTRUCTION PVT LTD

Madan Lal Bajaj Construction Pvt. Ltd.