Loading
Loading…
Loading…
| # | Company | Amount |
|---|---|---|
| 1 | ₹4.5 Cr |
Tender Value
₹5.4 Cr
EMD Value
₹10.7 L
Closing Date
27 Apr 2026, 3:00 pmClosed
DGM BSBCCL MUZAFFARPUR
DEPUTY GENERAL MANAGER MUZAFFARPUR
BSBCCL, Hospital Road, Sastri Nagar, Patna 800023
ANIL KUMAR
CGM
Construction Of 100 Beded Ambedkar Boys Hostel SC-ST AT Campus Of Bipin High School In Dist- West Champaran.
128525
78/BSBCCL/2025-26 GR01
Open Tender
CIVIL
Muzaffarpur
• Payment Receipt (EMD/Tender Fees/Tender Processing Fee)
• Total value of civil engineering construction work, in Rupees, Performed in last five years. (BALANCE SHEET, PROFIT & LOSS AND AUDIT REPORT DULY AUDITED BY CA.) Minimum annual financial turnover (in all classes of civil engineering construction works only) amount of construction work ,which must be at least equal to 50 % of estimated cost of works for which bid has been invited. The turnover will be indexed at the rate of 8% for a year
2020-21
2021-22
2022-23
2023-24
2024-25
• Amount in Rupees related to Work Experience of Similar nature -i) Satisfactory completed at least one similar work of value not less than 50% of estimated Cost (Escalation As per appendix ITB sl no-19) ii) The completion Certificate shall be issued by employer not below the rank of executive engineer or project manager. In case of Private client the completion certificate and valuation of the project issued by employer should be certified by the retired executive engineer/Registered value of Nationalised Bank/Insurance Company/Income Tax Department.
• Qty /Amount As Indicated In Any One Year In Last Five Year (Quantity Executed Must Be Satisfied By Concern Engineer In charge. In case of Private client the quantity executed will be issued by employer should be certified by the retired executive engineer/Registered value of Nationalised Bank/Insurance Company/Income Tax Department.
Furniture Work 15.56 Rs in Lac
Earthwork (Cutting) 632.81 CUM
Brick work 225.00 CUM
RCC+PCC 483.16 CUM
FLOORING 753.03 SQM
ELECTRICAL WORK 44.81 Rs in Lac
PHE Work 7.34 Rs in Lac
• Attach Affidavit in Prescribed Format mention in SBD.
• Proposed Methodology of Construction.
• AS PER SEC 2-1.5 MAX. AGE 5 YEARS ATTACHED OWNED VOUCHER /CASH MEMO/INVOICE AND AFFIDAVIT IN CASE OF LEASED/HIRE ON AND AFTER DATE OF TENDER
Type of Equipment Nos. Maxm. Age
Steel Shuttering 3000 Sft 5
Concrete Mixer with Integral weigh Batching facility 2 5
Vibrator (Plate & Niddle) 4 5
Water Tanker 1 5
• AS PER SEC 2-1.6 ATTACHED NECESSARY CERTIFICATE AND CURRENT AFFIDAVIT OF BOTH EMPLOYEE AND EMPLOYER ON AND AFTER DATE OF TENDER
1.Site Engineer / B.E. (Civil) + 03 Years Exp. (3 years in Building Construction) or Diploma in Civil + 7 year Exp. In Building construction or retired A.E. 1 no.
2.Site Supervisor /Fresh Graduate in Civil or Diploma Civil + 02 Years Exp. or retired I.T.I Holder 2 no.
• Litigation History if Any.
• Evidence of accesses to Financial Resources in Rupees-Evidence of access to or availability of credit facilities (10% of estimated cost), certified by bankers (for work under this bid).
• Undertaking -Able to invest a minimum of cost upto 25% of contract value of work. During implementation of contract.
• Registration No.-any Contractor Registered with Central Government/Any State Government/Any Public Sector Undertakings or an agency of National or International repute may tender, but Registration with Building Construction Department will be essential after issue of Letter of Acceptance.
• Experience Certificate of identified Sub Contractor (Electrical/PHE/Furniture) will be valid. Experience Certificate should be issued by at least Executive Engineer and equivalent officer. It is Mandatory to Attached Mutual Affidavit and Registration & Experience Certificate of Sub Contractor.
• Legal Status/Place of Registration/Principal Place of Business/Power of Attorney.
• (a) Amount of Existing commitments and ongoing works in Rupees (Bidder must declare themselves their all existing commitment hiding fact be sufficient cause for rejection.)
• (b) Amount of Work for which Bid already submitted, in Rupees.
• ( c ) BIDDING CAPACITY ( BC=AxNx3-B) SHOULD BE MORE THAN BOQ.
• Character Certificate of Bidder If Sub Contactors Affidavit Character Certificate Must Be Attached.
• NOC for Debar.
• GST Registration Certificate, PAN & Aadhar Document.
CIVIL
PERCENTAGE
L1
1
20 documents required · 20 mandatory
₹10,000
Processing Fee: 5900
₹10.7 L
CGM,BSBCCL (HQ)
16 Jul 2026
2 Apr 2026
28 Apr 2026
2 Apr 2026
27 Apr 2026
2 Apr 2026
11 Apr 2026
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
All work upto plinth level
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
All work from plinth level upto floor V level. Walls, columns, pillars, posts and struts
same as 2nd Floor slab
same as 2nd. Floor roof slab
250mm Brick drain
Code. SOR-2022
Construction of subgrade and Earthen Shoulder (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope an compacted to meet requirement of table No. 300-2)
Compacting original ground Compacting original ground supporting subgrade (Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300-2 for subgrade construction)
Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work
Cement mortar 1 : 4 (1 cement: 4 coarse sand )
Cement mortar 1 : 4 (1 cement: 4 coarse sand )
Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm,made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and…
Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS : 12823 marked, exterior grade (Grade I Type II), having one side decorative lamination and other side balancing lamination, including IInd class teakwood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge.
Providing and fixing steel glazed window & ventilators
Labour for cutting of M.S. angle iron post to required length, one end splitted as fish tailed in a length of 150mm complete as per building
Edges of slabs and breaks in floors and walis- Under 20 cms wide
Extra for provinding for edge moulding
Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.
IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.
IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area.
IVth course of 400 micron thick PVC sheet (overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm
With average thickness of 120mm and minimum thickness at Khurra as 65 mm.
Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,
Supplying and fixing-rolling shuters of approved make. Madeof required size of GI sheets interlocked together through theirentire length and jointed together at the end by end locksmounted on specially designed pipe shaft with brackets, sideguides and arragements for inside and outside locking withpush and pull operation complete including the cost ofproviding and fixing necessary 27.5cm long wire springsmanufactured from high tensile steel wire of adequatestrength conforming to IS:4454-part1 and GI top cover ofrequired thickness for rolling shutters including Providing and fixing ball bearing for rolling shutters
Bricks (lead - 1 km kutcha + 7 km pucca)
Coarse sand (Lead - 169 km)
Stone Chips (Lead - 284 km)
Local sand (1 km kutcha + 2 km pucca)
Cement
Bricks
Plantation of trees
Shrubs / Creeps
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
Sand cast iron S&S pipe as per IS: 1729
Providing and fixing PTMT Waste Coupling for wash basin and sink,of approved quality and colour.
Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms
Bottle t rap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10(1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominalsize) and inside plastering with cement mortar 1:3 (1 cement : 3coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.
150 mm nominal size square 100 mm diameter of the inner hinged round grating
Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.
Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.
Cutting holes up to 30x30 cm in walls including making good the same:
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Extra for depth beyond 45 cm of brick masonry chamber
Septic Tank - 1 No[6.60 mtr (long) x 2.80 mtr (wide) x 1.40 mtr (deep)] Rs.1,43,064.00
Supplying,installing,testing and commissioning submersible pump 2HP with stater & wire of necessary length
Earth Work in filling in campus with ordinary soil vide classfication of soil (item-A) obtained from borrow pits or any other ingradients likely to detoriate effect the stability of the embankment including breaking the clods maximum to 60mm cube placing the earth in layers not exceeding 225mm in loose thickness, rough dressing including cost of cutting and removing shrubs roots falling in borrow area all complete as per approved design, specification and direction of E/I. (Lead-1 Km kutcha + 1 km pucca)
Add Gst 5.36%
Bed Dimension : 1950 x 900 x 650 mm (H) Structure is made up of 40 mm dia CRC tube with thickness 18 gauge. Horizontal base is made from steel sheet the thickness 14 gauge. Horizontal base will be stiffened with appropriate longitudinal 3 v shape sheet and lateral stiffeners 2 steel pipes with powder coating. Manufactured out of ISO 9001, ISO14001 and OSHSAS 18001 certified Plant and product certified for BIFMA performance test .(Size : 2000 x 900 x 650 mm (H)
Supplying and fixing of Mattress (size : 75"x36" x 2" thick) at site, with complete in all respect or as per direction of E/I
Pillow
King Size Bed - Size : 1800L x2000W x 900Ht. construction of bed shall be knock down type in nature. Bed Head Board Made out of 25mm thick Prelaminated Particle Board attach to wall. Bed Box made out of 18 mm thk Prelaminated Particle Board.Mattress Panel and below support Made out of 12 mm thick Prelaminated Particle Board . 50mm x 50mm Solid wood leg with matt polish finish at foot board and lockable castors at headboard side at bottom of bed for maintanance.All exposed edges to be provided with 2.0 mm thick matching grain PVC lipping fixed with hot melt glue.The product is BIFMA and FSC certified
King size Matterss size- 78"x72" with 4" thik Bonded Matterss.
Study Table & Chair Dimension : DESK - 600 W x 480 D x 750 H SEAT - 868 H x 500 W x S 450 Finish/Coating : Powder Coating Material : MILD STEEL TUBULAR SECTION OVAL Tube 35 x 15 SQ. Tube 25x25 and PLB & Moulded wood Total Weight : 23Kg Available Base Frame : Knock down Features : >SEMI KNOCKDOWN > 11 TANK HOT ZINC PHOSPHATING PRE TREATMET PROCESS> Powder Coated The Product should be BIFMA,ISO-9001,ISO-14001 ,OHSAS18001 ,IGBC,FIRA Certified. As Per direction given by E/I.
Wadern's Chamber Table / common room Size: Executive Desk Size - 1800mm (W) x 900mm (D) x 750mm (H) Side Unit - 1800mm (W) x 600mm (D) x 675mm (H) Combination of metal and wood reflects dynamism. Sleek floating top gives aesthetic and trendy look. Open rectanglular section legs with small modesty gives the table trendy, airy open look.
Seat/Back Assembly: The seat is made up of 1.2 ±0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA- P14-18 and upholstered with fabric moulded Polyurethane Foam. The back is made up of 1.2 ±0.1cm hot pressed plywood upholstered with fabric moulded polyurethane foam. The back ply and foam is designed with contoured lumber support for comfortable seating posture. Mid Back Size - 48cm (W) x 64.5cm (H). Seat Size - 51cm (W) x 48cm (D) Armrest (Adjustable): The armrest top is made up of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height is adjustable up to 6.5±0.5cm in 5 steps & also has swivel adjustment of 22° ± 2° on both sides. Knee Tilt Synchro Mechanism with Seat Deapth Adjustment Mechanism: The mechanism is designed with the following features -360° revolving type, Single point control, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 4-position locking with anti-shock feature, Seat back tilting ratio of 1:2 & Seat depth adjustment of 6.0 ± 0.5cm can be locked in 6 positions. Adjustable Backrest: The backrest consists of a sliding up down mechanism, which can be adjusted in the range of 7.5 ± 0.5cm and can be locked in 4 positions for correct position of lumber support. Pneumatic Height Adjustment: The pneumatic height adjustment has an adjustment of 9.0 ± 0.3cm. Pedestal Assembly: The pedestal is fabricated from 0.2 ± 0.2cm thick HR sheet (IS : DD 1079 / HR skin pass), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 66.0±0.5cm Pitch-center dia. (76.0 ± 1.0cm with castors). Twin Wheel Castors: The twin wheel castors are injection moulded in black Nylon.
Visitor Chair-cantiliver chair size (back H-470 *W-460,Seat -D-460*470)mm & mim.Height-430mm. Multipurpose fixed cantiliver chair & armest with pading 7 metal base. A 14mm thick, BWR grade plywood (IS:303) is used to make the seat and back. Deep cushioned back and seat confirm to body contours for proper aligment, posture and all day comfort 5% post consumed recycled content & 30% total recycle content. The Product should be BIFMA. Green guard, AGSI Certifide, ISO 14001, ISO 50001:2011 Certified. Color- Black.
Cantilever chair-chair size (w)595 mm x (D)510 mm x (H)875mm multi purpose fixed chair metal frame PU padding on armrest. Cushion upholstery in leathere with four leg metal legs with matt finish. The product should be BIFMA Green Guard AGSI Certified ISO 50001:2011 Certified. Color- Black.
4 Door Glass Book Case L-900 mm x D-450 mm x H-2000mm Bookcase 4 doors with cam. Body-22 gauge Doors 20 gauge made of mild steel with powder coated
Dining table(3'x3')Table time out 4 seater Size: 900x900x750mm :- Work surface 25 m.m. Thick M D F Board P U painting Under Structure of Ms. Powder Coted Pipe dia 38 mm. The Product should be BIFMA( Original) and IGBC Certified as Per direction given by E/I.
DINING TABLE Work Surface: 25mm Thick (±1mm) Base Material - 25mm MDF Board on top PU painting of Minium 2H hardness with 75% glass as per color chart, combination color graphics on the centre. Color as per color chart. Brown laminate on bottom. Specially profiled edge for comfort. Understructure: Bend pipe understructure of MS. Powder Coated. Pipe dia. 38mm, 2mm thk. Understructure fitted with top by SS machine screws. Legs: MS Powder coated legs for PU top & SS legs for membrane top. 38mm dia pipe legs are fixed with understurcture and table top. Glide: Plastic Glide fixed at the understructure to prevent the damage of table top druing stacking. Size: Ground Base - 2450mm (L) x 1175mm (W). Surface Top - 2400.8mm (L) x 1050.4mm (W) & Height - 750mm (H)
DINING SEAT Seat/Back: Seat & Back are injection moulded in PP. They are snap fitted on the understructure assembly and fixed with self-taping screws Approx. Back Size : 37.0cm (W) x 25.5cm (H) Approx. Seat Size : 40.5cm (W) x 40.5cm (D) Understructure Assembly: The understructure assembly is a welded frame assy
Providing and fixing steel body stool size top 300mm dia and height 750mm with all complete job .The Product should be BIFMA,( Original) and IGBC Certified as Per direction given by E/I.
3 sector chair (Chrome) Made of Cushion with high density cold cured self -skinned pre -molded foam of 50-60 density the shape of plywood. Upholstery is done by using high-pressure pneumatic spray glue and pneumatic press over crome base & legs etc. all complete as per direction of E/I
ELECTRICAL WORKS
Supplying and fixing following ways, surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amp tinned copper bus bar, common neutral link, earth bar, din bar, for mounting MCB's (but without MCB's and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)
S/F Electronics Musical call bell suitable for D.C/A.C. single phase 230 copmplete as required.
Supplying and drawing following pair 0.5 sq. mm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed PVC conduit as required.
Rottary Handle
Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.
Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel at least 2 mm thick, vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.
P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)
Supply, installation, testing and commissioning of Silent Type diesel generating set comprising of M&M make engine CPCB IV Model 126 BHP @ NTP , 1500 RPM Coupled to 100 KVA LEYROMER 3 PHASE 415 VOLT ,50 HZ Alternator mounted on acommon base frame along with other accessories i.e. fuel tank AMF CONTROL PANEL, BATTERY WITH LEADS AND ACOUSTIC ENCLOSURE
Supply, installation, testing and commissioning of 100 kVA, Fully Copper(Level-2) 11kV/433V, 3 phase, 50 Hz, Delta star, DYn11, ONAN transformer with Off load tap changer from +5% to -10% in steps of ±2.5%, class F insulation, complete with WTI and scanner for alarm & trip, unidirectional rollers, cable end box for termination of HT cables & Bus duct for LT side complete with rating and technical name plate, earthing terminals with lugs, lifting lugs in all respect with all necessary standard accessories and as per IS. The transformer shall have suitable enclosure for providing neutral CT on earthed star point with connector for connection to REF relay provided in Main panel. All routing test as per IS shall be conducted on the transformer. The Transformer Enclosure shall have suitably designed Louvers for Air Circulation & efficient Cooling. The enclosure shall be Epoxy Powder coated. The transformer shall be subjected to all routine tests as per IS/IEC standards. Type test certificate shall be submitted. The transformer shall meet latest ECBC requirments.Make-Servokon / Schnneider/ Siemens/Powerstar/Infra Power/C&S etc of Higher grade.(Electrical Inspector Charges included)
11 KV DOUBLE POLE STRUCTURE:- Supply, erection, testing and commissioning of 2 pole structure for providing 1 No. 11KV,400A GOS in accordance with IE rules, & local authority specification and drawings and comprising of the following items below.
Design, Supply, Installation, Testing and Commissioning of 20 KW Solar System with all below items. (Approved OEM)
Supply, Installation, Testing and Commissioning of on grid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mountedon Aluminium/GI structure of suitable strength with following components complete as required:-a)Solar Photovoltaic Module of capacity 330Wp or above, manufactured in India, conforming to IS14286/ IEC61215, IS/IEC61730-Part-1, IS/ IEC61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than16.5%. PV modules used in solar power plants/systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% attheend of 25 years. b)Power Conditioning Unit (PCU) of 350-800V DC Input voltage range and 400V AC, three phase, 4 wire, 50Hz+/-2.5Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than3% and suitable for ambient temperature from 0 to 50 degreeC. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d)Fixing of Array junction box & Main junction box with IP65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required. (Make-TATA/ADANI/WAREE/VIKRAM etc Note:-All Electricals & Mechanical items included.
CCTV Network Camera Dome 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T
CCTV Network Camera Bullet 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264 /MJPEG /H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T
Display : Screen size – 42 inch or above(LG/Sony/Samsung/ Philips), Panel Technology IPS, Surveillance Monitor
Supply / Installation and Commissioning of 24 Port Network Switch GIGA PoE,IEEE 802.3at and IEEE 802.3af Power over Ethernet (PoE) compliant,24x10/100/1000 Mbps Auto-MDIX PoE ports,Provides up to 30 watts per PoE port,PoE power budget 370W,4 KV surge protection for PoE ports,IEEE 802.3x flow control support,Plug-and-play installation,8.8 Gbps switching fabric,2.75 Mbits RAM Data Buffer,4K MAC address entries,Sturdy metal enclosure
Supply Installation Testing & Commissioning of IP Video Storage device shall be a Min 30 days recording,Min RAID-3 protected, all-in-one recording for network surveillance systems It shall be designed for high speed, high capacity Network video storage and high performance play back applications.The video storage array shall have Min 5 internal HDDs (4 x 10TB) Min 4 TB. The storage array shall provide an audible alarm to notify the user in the event of a failure. The system should be such that the vedio recording from camera should be done directly on storage array and directions of Engineer-in-charge. LED indicators Features trayless hard drive insertion Dissipates heat efficiently with aluminum housing. Software configuration if any.Complete in all respects.
Supply fitting fixing Rack 19" 12U fully powder coated complete etc as required with complete accessories (5 amp x 6 socket, wire manager, rack fan) VALRACK/ Netrack make. Wit all necessary items.
ABC Powder Type (Stored Pressure) Fire Extinguisher, 4Kg. Capacity, ISI Mark (IS:15683), squeeze grip valve, operating temperature (+5)° C to (+55)° C for Class 3A type of Fire filled with MAP ABC Powder, Complete in all respect. (Guaranty/Waranty must not be less than 5 years) MAKE:-KALPEX/CEASEFIRE/LIFEGUARD/SAFEAXE etc of Higher grade.
CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683), squeeze grip valve, operating temperature (-30)° to (55)° C for Class 13B type of Fire fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.(Guaranty/Waranty must not be less than 5 years) MAKE:-KALPEX/CEASEFIRE/LIFEGUARD/SAFEAXE etc of Higher grade.
32 bit microprocessor based Intelligent Addressable Fire Alarm Control panel with 4 loops with battery back up. The panel would be modular, decentralized, with The panel shall be consisting with minimum 240 character LCD display and for networking. The Panel would be able to record atleast 60,000 events history. Each loop would be capable to have atleast 250 addressable detectors and addressable devices with up to 3.5km loop length. Make: Schrack Seconet (Vds approved)
1 KVA LINE INTERACTIVE UPS WITH 30 MIN BATTERY BACK UP
Supplying and fixing Intelligent Addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.
Supplying and fixing Intelligent Addressable type Smoke/Heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.
Sypplying and fixing Intelligent Addressable Manual Call Point having inbuilt short circuit isolator i/c testing and commissiong etc as reqd.
Addressable sounder with interface module, power supply for sounder and programmable by software having integrated short circuit isolator & having operating temperature -10⁰C to + 55⁰C
Analogue Addressable Monitor module with IP66 casing containing four relay inputs, each containing a potential-free DPDT contact with a fail-safe and in-built short circuit isolator The ambient temperature range shall be -20C to +60C.
4"/4" JB for mounting of detectors & other accessories with necessary fittings
Supplying and fixing Outdoor Electronic Sounder with 4 distinct tone including 40W Speaker with required accessories as reqd.
Supplying and laying of 2x1.5 sq.mm. ISI marked copper armourd conductor cable with gland scoket and other wiring accessories on the existing surface/tray/shaft etc as reqd
Providing and fixing M.S. pipe to I.S. 1239 (Heavy class) complete with all supports & fittings like, unions, couplings, bends, elbows, tees, offsets,reducers, flanges as per table 'E' etc. to complete the work as per the requirement at site including painting with one coat of primer after surface preparartion and two coats of synthetic enamel paint, cutting and making good the walls good complete. Pipe upto 40 mm dia threaded joints with holdtite, 50 mm dia and above should be welded joint ( all type) (internal works/External Works).
Providing & Fixing dust and Verin proof motor control panel fabricated with 14 SWG MS sheet with stove enamelled paint and comprising of Fire Pump.
Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as
Providing and fixing first aid fire hose reel drum wall mounting, swinging type(Powder coated finish in fire red) fitted with 20 mm dia. 30 m long high pressure hose(IS:444, Type-2) with 5 mm outlet SS nozzle with shut off valve (IS:8090). complete hose reel drum shall be conforming to IS:884) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall.
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :
Code. SOR-2020
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.
1.4.8 (1 Cement :4 coarse sand :8 graded stone agregate 40 mm nominal size)
per 50 kg cement
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work
Extra tor Brick work in superstructure above plinth level upto floor V cum
250 mm th Brick work in C.M (1:6)
125 mm th Brick work in C.M (1:4)
Providing and fixing to existing door frames.
Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm,made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and…
Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, with necessary screws etc. complete:
Providing and fixing aluminium hanging floor door stopper anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete.
Providing and fixing ISI marked steel wire gauged doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs, 10 cm long , embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using galvanized M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm with 12 mm mild steel beading complete including applying a priming coat of approved steel primer, but excluding the cost of other fittings except necessary hinges or pivots as required
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
With ready mixed red oxide zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel works
Forming groove of uniform size from 12 x 12 mm and upto 25 x 15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-charge.
Finishing walls with Acrylic Smooth exterior paint of required shade :
1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.
IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.
IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area.
IVth course of 400 micron thick PVC sheet (overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm
With average thickness of 120mm and minimum thickness at Khurra as 65 mm.
Providing plinth protection 750 mm wide consisting of 12 mm thick cement plaster 1;6 with neat cement punning over 75 mm thick P.C.C. (1:3 :6) over brick flat soling over 75 mm thick local sand filling all complete
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floor.
Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,
Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.
Bricks (lead - 1 km kutcha + 7 km pucca)
Coarse Sand (Lead- 140 km) Kiul
Stone Chips (Lead- 240 km) Manpur Gaya
Local sand (1 km kutcha + 2 km pucca)
Cement
Bricks
Providing and fixing water closet squatting pan (Indian type W.C.pan with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device handle lever conforming to IS : 7231, with all fittings and floors wherever required :
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required :
Sand cast iron S&S pipe as per IS: 1729
114 mm off sets
152 mm off sets
Providing and fixing terminal guard :
Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :
Providing and fixing trap of self cleansing design with screwed down orhinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :
Providing and fixing PTMT Waste Coupling for wash basin and sink,of approved quality and colour.
150 mm nominal size square 100 mm diameter of the inner hinged round grating
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)
Septic Tank - 2 Nos. x @ Rs. 3,24,501/- 6.6 mtr (long) x 2.80 mtr (wide) x 1.40 mtr (deep) {of inside finished size as per design & drawing
Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.
Supplying,installing,testing and commissioning submersible pump 2HP with stater & wire of necessary length
Construction of subgrade and Earthen Shoulder (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope an compacted to meet requirement of table No. 300-2)
Compacting original ground Compacting original ground supporting subgrade (Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300-2 for subgrade construction)
Supplying and Filling with local sand and under floors including, watering, ramming consolidating and dressing complete.
Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I.
Providing designation 100 A one brick on edge soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,
Edges of slabs and breaks in floors and walis- Under 20 cms wide
Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.
Bricks (lead - 1 km kutcha + 7 km pucca)
Coarse Sand (Lead- 140 km) Kiul
Stone Chips (Lead- 240 km) Manpur Gaya
Local sand (1 km kutcha + 2 km pucca)
Earth
Cement
Bricks
Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick
Columns, Pillars, Piers, Abutments, Post and struts
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
All work upto plinth level
All work from plinth level upto floor V level.
Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :
Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work
Extra tor Brick work in superstructure above plinth level upto floor V cum
Forming groove of uniform size from 12 x 12 mm and upto 25 x 15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-charge.
Labour for cutting of M.S. angle iron post to required length, one end splitted as fish tailed in a length of 150mm complete as per building
Earth Work in filling in campus with ordinary soil vide classfication of soil (item-A) obtained from borrow pits or any other ingradients likely to detoriate effect the stability of the embankment including breaking the clods maximum to 60mm cube placing the earth in layers not exceeding 225mm in loose thickness, rough dressing including cost of cutting and removing shrubs roots falling in borrow area all complete as per approved design, specification and direction of E/I. (Lead-1 Km kutcha + 1 km pucca)
Bricks (lead - 1 km kutcha + 7 km pucca)
Coarse Sand (Lead- 140 km) Kiul
Stone Chips (Lead- 240 km) Manpur Gaya
Local sand (1 km kutcha + 2 km pucca)
Cement
Bricks
Bed Dimension : 1950 x 900 x 650 mm (H) Structure is made up of 40 mm dia CRC tube with thickness 18 gauge. Horizontal base is made from steel sheet the thickness 14 gauge. Horizontal base will be stiffened with appropriate longitudinal 3 v shape sheet and lateral stiffeners 2 steel pipes with powder coating. Manufactured out of ISO 9001, ISO14001 and OSHSAS 18001 certified Plant and product certified for BIFMA performance test .(Size : 2000 x 900 x 650 mm (H)
Supplying and fixing of Mattress (size : 75"x36" x 2" thick) at site, with complete in all respect or as per direction of E/I
Pillow
King Size Bed - Size : 1800L x2000W x 900Ht. construction of bed shall be knock down type in nature. Bed Head Board Made out of 25mm thick Prelaminated Particle Board attach to wall. Bed Box made out of 18 mm thk Prelaminated Particle Board.Mattress Panel and below support Made out of 12 mm thick Prelaminated Particle Board . 50mm x 50mm Solid wood leg with matt polish finish at foot board and lockable castors at headboard side at bottom of bed for maintanance.All exposed edges to be provided with 2.0 mm thick matching grain PVC lipping fixed with hot melt glue.The product is BIFMA and FSC certified
King size Matterss size- 78"x72" with 4" thik Bonded Matterss.
Study Table & Chair Dimension : DESK - 600 W x 480 D x 750 H SEAT - 868 H x 500 W x S 450 Finish/Coating : Powder Coating Material : MILD STEEL TUBULAR SECTION OVAL Tube 35 x 15 SQ. Tube 25x25 and PLB & Moulded wood Total Weight : 23Kg Available Base Frame : Knock down Features : >SEMI KNOCKDOWN > 11 TANK HOT ZINC PHOSPHATING PRE TREATMET PROCESS> Powder Coated The Product should be BIFMA,ISO-9001,ISO-14001 ,OHSAS18001 ,IGBC,FIRA Certified. As Per direction given by E/I.
Wadern's Chamber Table / common room Size: Executive Desk Size - 1800mm (W) x 900mm (D) x 750mm (H) Side Unit - 1800mm (W) x 600mm (D) x 675mm (H) Combination of metal and wood reflects dynamism. Sleek floating top gives aesthetic and trendy look. Open rectanglular section legs with small modesty gives the table trendy, airy open look.
Seat/Back Assembly: The seat is made up of 1.2 ±0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA- P14-18 and upholstered with fabric moulded Polyurethane Foam. The back is made up of 1.2 ±0.1cm hot pressed plywood upholstered with fabric moulded polyurethane foam. The back ply and foam is designed with contoured lumber support for comfortable seating posture. Mid Back Size - 48cm (W) x 64.5cm (H). Seat Size - 51cm (W) x 48cm (D) Armrest (Adjustable): The armrest top is made up of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height is adjustable up to 6.5±0.5cm in 5 steps & also has swivel adjustment of 22° ± 2° on both sides. Knee Tilt Synchro Mechanism with Seat Deapth Adjustment Mechanism: The mechanism is designed with the following features -360° revolving type, Single point control, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 4-position locking with anti-shock feature, Seat back tilting ratio of 1:2 & Seat depth adjustment of 6.0 ± 0.5cm can be locked in 6 positions. Adjustable Backrest: The backrest consists of a sliding up down mechanism, which can be adjusted in the range of 7.5 ± 0.5cm and can be locked in 4 positions for correct position of lumber support. Pneumatic Height Adjustment: The pneumatic height adjustment has an adjustment of 9.0 ± 0.3cm. Pedestal Assembly: The pedestal is fabricated from 0.2 ± 0.2cm thick HR sheet (IS : DD 1079 / HR skin pass), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 66.0±0.5cm Pitch-center dia. (76.0 ± 1.0cm with castors). Twin Wheel Castors: The twin wheel castors are injection moulded in black Nylon.
Visitor Chair-cantiliver chair size (back H-470 *W-460,Seat -D-460*470)mm & mim.Height-430mm. Multipurpose fixed cantiliver chair & armest with pading 7 metal base. A 14mm thick, BWR grade plywood (IS:303) is used to make the seat and back. Deep cushioned back and seat confirm to body contours for proper aligment, posture and all day comfort 5% post consumed recycled content & 30% total recycle content. The Product should be BIFMA. Green guard, AGSI Certifide, ISO 14001, ISO 50001:2011 Certified. Color- Black.
Cantilever chair-chair size (w)595 mm x (D)510 mm x (H)875mm multi purpose fixed chair metal frame PU padding on armrest. Cushion upholstery in leathere with four leg metal legs with matt finish. The product should be BIFMA Green Guard AGSI Certified ISO 50001:2011 Certified. Color- Black.
4 Door Glass Book Case L-900 mm x D-450 mm x H-2000mm Bookcase 4 doors with cam. Body-22 gauge Doors 20 gauge made of mild steel with powder coated
Dining table(3'x3')Table time out 4 seater Size: 900x900x750mm :- Work surface 25 m.m. Thick M D F Board P U painting Under Structure of Ms. Powder Coted Pipe dia 38 mm. The Product should be BIFMA( Original) and IGBC Certified as Per direction given by E/I.
DINING TABLE Work Surface: 25mm Thick (±1mm) Base Material - 25mm MDF Board on top PU painting of Minium 2H hardness with 75% glass as per color chart, combination color graphics on the centre. Color as per color chart. Brown laminate on bottom. Specially profiled edge for comfort. Understructure: Bend pipe understructure of MS. Powder Coated. Pipe dia. 38mm, 2mm thk. Understructure fitted with top by SS machine screws. Legs: MS Powder coated legs for PU top & SS legs for membrane top. 38mm dia pipe legs are fixed with understurcture and table top. Glide: Plastic Glide fixed at the understructure to prevent the damage of table top druing stacking. Size: Ground Base - 2450mm (L) x 1175mm (W). Surface Top - 2400.8mm (L) x 1050.4mm (W) & Height - 750mm (H)
DINING SEAT Seat/Back: Seat & Back are injection moulded in PP. They are snap fitted on the understructure assembly and fixed with self-taping screws Approx. Back Size : 37.0cm (W) x 25.5cm (H) Approx. Seat Size : 40.5cm (W) x 40.5cm (D) Understructure Assembly: The understructure assembly is a welded frame assy
Providing and fixing steel body stool size top 300mm dia and height 750mm with all complete job .The Product should be BIFMA,( Original) and IGBC Certified as Per direction given by E/I.
3 sector chair (Chrome) Made of Cushion with high density cold cured self -skinned pre -molded foam of 50-60 density the shape of plywood. Upholstery is done by using high-pressure pneumatic spray glue and pneumatic press over crome base & legs etc. all complete as per direction of E/I
Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc.as required
Supplying and fixing PVC/G.I box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.
Supplying and fixing modular type 2 pin telephone socke/ speaker outlet on the existing modular plate & box including making connection,excluding moduler plate etc. as required.
Supplying and fixing modular T.V antenna socket on the existing modular plate and metal box including making connection, etc. as required.
Supply & fixing 2+ 8 way double door SP & N, sheet steel, MCB distribution board, 240 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Lighting DB
Supply and fixing 320 A 4 Pole on load / panel moumted change over switch in existing cubical panel board making connection, earthing the body etc.as required
Supplay and fixing wall /floor mounted cubicle panel board fabricated with 16 gauge iron sheet suitable for panel mounted switch discconnector including Bus bar chamber insulator and painting etc as required.9but without bus bar copper strip)
S/F digital voltmeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.
S/F digital ammeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.
Supply and Installation of regular/standard module AC ceiling fan of 1400 mm sweep including wiring the down rod of standard length 9 upto 30 cm ) with 1.5 sq mm FR pvc insulated copper conductor etc as required.
Supply and Installation of 300 mm 230volt AC exhaust fan in the existing opening including making good the damage connection testing commissioning etc as required.
Supplying and fixing recess/surface mounted 23/24 (1ft X 1ft) watt LED downlighter complete with integrated electronic driver & LED directly on ceiling/false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.
SSupplying and fixing single wall mounted 9/10 watt (2 ft long) LED type batten fitting complete with electronic driver and LED etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.
Supplying and fixing 90 watt LED type street light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc, on pole/building including connection with FR PVC insulated copper conductor cable and earthing the body etc. as required.
P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.
P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)
Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size
3KVA on grid solar pannel set complete with battary,solar plate,cable for plate to solar pannel etc. with 4hr back up.
Supply and Installation of Indoor Dome IR Network Camera (1/2.7" CMOS sensor, Mini. Pixel of 2560*1920 or higher video quality, frame rate of Up To 25fps @ 5MP, H.265, H.264 & MJPEg video compression, 2.8mm Fixed lens, physical ICR filter of both day and night, 30mtr IR Distance,120dB WDR ,3Streams Supported, WDR , 3D-DNR for noise reduction, BLC, ICR, EXIR, Audio In and Out, Alam in and Out. IPv4/IPv6 network supported, IP67, IK10 rated for weatherproofing, ONVIF ver 2.2 or higher, PoE IEEE 802. 3af (UL, FCC, CE, BIS certified.). Make Hikvision/Bosch/Honeywell
Supply and Installation of outdoor Bullet IR Network Camera 1/2.7" CMOS, ICR, 2592*1944@ 25fps, 5 MP H.265/H.264/MJPEG, Triple streams, DC12V & PoE, Micro SD card slot up to 256 GB, Alarm in/out , Audio 1/1, IP67, 2.7-13.5mm Motorized Varifocal lens, IR anti-reflection window, Built-in bracket, IR range: up to 50m, Digital WDR Range, 3D-DNR for noise reduction, Audio In and Out, Alam in and Out IPv4 network supported, IP67 rated for weather proofing, ONVIF, POE IEEE 802.3af, (UL, FCC, CE, BIS certified). Make-Panasonic/ Bosch/Honeywell
Supply, installation, testing and commissioning of all-in-one recording solution for up to 16 to 32 channels, Pre-installed, pre-configured IP storage solution with 8-16 TB storage capacity, RAID-5 protected,Hot-swappable hard drives,Intel Xeon Quad Core X3430 (2.4 GHz, 8 M Cache, 95 W) Processor,4-8 GB memory installed, 2U rack mount, Temperature +10 °C to +35 °C, Relative humidity-8 to 90% (non-condensing), CE, UL Certified. Recording shall be calculated for all cameras at full frame rate & resolution for upto 15 days .with Intel i5 processor, 4-32GB RAM, 2TB HDD, 2-4 GB Dedicated NVidia Graphics card, Windows 7-10 or as recommended by VMS Software. The Workstation shall be suitable for any open platform software as required as per specification. . MAKE - Bosch / PELCO/ ONCAM
32" Full HD LED Professional Display for Monitoring with mounting accessories.
Layer 2 networking switch, 24 # 10/100/1000 BT ports, PoE as per 802.3a/f with 2 Nos of Fiber interface ports.
Supplying and laying of SOLID CABLE, CAT6 UTP, 4PAIR, 23AWG, LSZH CM,BLUE colour through existing conduit /trunk complete as required & as per Direction of Engineer-In-Charge.MAKE : DIGISOL/DIGILINK
19" 6U Rack for Switches complete as required
3x3 Juncation box with face place complete for Camera
Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size
ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect
CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.
BSBCCL
DARBHANGA
Code. SOR-2022
TMTC-500- 8mm dia .
TMTC-500-10 mm dia.
TMTC-500-12 mm dia.
TMT FE-500-16 mm dia.
TMT FE-500-20 mm dia.
TMT FE-500-25 mm dia.
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
All work upto plinth level
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
All work from plinth level upto floor V level. Walls, columns, pillars, posts and struts
Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work
Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work Up to PL
Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work
Extra tor Brick work in superstructure above plinth level upto floor V cum
Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multichambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.
Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.)
Providing and fixing ISI marked steel wire gauged doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs, 10 cm long , embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using galvanized M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm with 12 mm mild steel beading complete including applying a priming coat of approved steel primer, but excluding the cost of other fittings except necessary hinges or pivots as required
25 kg/sqm
20kg/sqm
Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.
IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.
IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area.
IVth course of 400 micron thick PVC sheet (overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm
n*l*b+(l+b)*2*n*h
Providing plinth protection 750 mm wide consisting of 12 mm thick cement plaster 1;6 with neat cement punning over 75 mm thick P.C.C. (1:3 :6) over brick flat soling over 75 mm thick local sand filling all complete
Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,
Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.
Bricks (lead - 1 km kutcha + 7 km pucca)
Coarse Sand (Lead- 139 km)
Stone Chips (Lead- 220 km)
Local sand (1 km kutcha + 2 km pucca)
Cement
Bricks
BSBCCL
DARBHANGA
Description of Work
Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the likes
Clearing jungle including uprooting of rank vegetation ,grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.
Coarse Sand
Stone Chips
Bricks
Local Sand
Cement
Carriage cost of Earth
BUXAR
Item of Work
Particulars
Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :
Area vide Item no. 14
Area vide Item no. 15
BUXAR
Item of Work
PROJECT :- PROPOSED Construction of 100 Beded Ambedkar Boys Hostel SC-ST AT Campus Of Bipin High School in Dist- West Champaran
Name of Item
Rs (in Lakh)
Rs (in Lakh)
Rs (in Lakh)
Code. SOR-
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
All work upto plinth level
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
All work from plinth level upto floor V level. Walls, columns, pillars, posts and struts
same as 2nd Floor slab
same as 2nd. Floor roof slab
250mm Brick drain
Code. SOR-2022
Construction of subgrade and Earthen Shoulder (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope an compacted to meet requirement of table No. 300-2)
Compacting original ground Compacting original ground supporting subgrade (Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300-2 for subgrade construction)
Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work
Cement mortar 1 : 4 (1 cement: 4 coarse sand )
Cement mortar 1 : 4 (1 cement: 4 coarse sand )
Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm,made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and…
Providing and fixing cup board shutters 25 mm thick, with Pre-laminated flat pressed three layer particle board or graded wood particle board IS : 12823 marked, exterior grade (Grade I Type II), having one side decorative lamination and other side balancing lamination, including IInd class teakwood lipping of 25 mm wide x12 mm thick with necessary screws and bright finished stainless steel piano hinges, complete as per direction of the Engineer-in-Charge.
Providing and fixing steel glazed window & ventilators
Labour for cutting of M.S. angle iron post to required length, one end splitted as fish tailed in a length of 150mm complete as per building
Edges of slabs and breaks in floors and walis- Under 20 cms wide
Extra for provinding for edge moulding
Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.
IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.
IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area.
IVth course of 400 micron thick PVC sheet (overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm
With average thickness of 120mm and minimum thickness at Khurra as 65 mm.
Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,
Supplying and fixing-rolling shuters of approved make. Madeof required size of GI sheets interlocked together through theirentire length and jointed together at the end by end locksmounted on specially designed pipe shaft with brackets, sideguides and arragements for inside and outside locking withpush and pull operation complete including the cost ofproviding and fixing necessary 27.5cm long wire springsmanufactured from high tensile steel wire of adequatestrength conforming to IS:4454-part1 and GI top cover ofrequired thickness for rolling shutters including Providing and fixing ball bearing for rolling shutters
Bricks (lead - 1 km kutcha + 7 km pucca)
Coarse sand (Lead - 169 km)
Stone Chips (Lead - 284 km)
Local sand (1 km kutcha + 2 km pucca)
Cement
Bricks
Plantation of trees
Shrubs / Creeps
Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
Providing and fixing 600x120x5 mm glass shelf with edges round off,supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.
Sand cast iron S&S pipe as per IS: 1729
Providing and fixing PTMT Waste Coupling for wash basin and sink,of approved quality and colour.
Waste coupling 38 mm dia of 83 mm length and 77mm breadth, weighing not less than 60 gms
Bottle t rap 31mm single piece moulded with height of 270mm, effective length of tail pipe 260 mm from the centre of the waste coupling, 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms
Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve,with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10(1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominalsize) and inside plastering with cement mortar 1:3 (1 cement : 3coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :
Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 :
Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.
150 mm nominal size square 100 mm diameter of the inner hinged round grating
Providing and fixing PTMT soap Dish Holder having length of 138mm,breadth 102mm, height of 75mm with concealed fitting arrangements,weighing not less than 106 gms.
Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.
Cutting holes up to 30x30 cm in walls including making good the same:
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Extra for depth beyond 45 cm of brick masonry chamber
Septic Tank - 1 No[6.60 mtr (long) x 2.80 mtr (wide) x 1.40 mtr (deep)] Rs.1,43,064.00
Supplying,installing,testing and commissioning submersible pump 2HP with stater & wire of necessary length
Earth Work in filling in campus with ordinary soil vide classfication of soil (item-A) obtained from borrow pits or any other ingradients likely to detoriate effect the stability of the embankment including breaking the clods maximum to 60mm cube placing the earth in layers not exceeding 225mm in loose thickness, rough dressing including cost of cutting and removing shrubs roots falling in borrow area all complete as per approved design, specification and direction of E/I. (Lead-1 Km kutcha + 1 km pucca)
Add Gst 5.36%
Bed Dimension : 1950 x 900 x 650 mm (H) Structure is made up of 40 mm dia CRC tube with thickness 18 gauge. Horizontal base is made from steel sheet the thickness 14 gauge. Horizontal base will be stiffened with appropriate longitudinal 3 v shape sheet and lateral stiffeners 2 steel pipes with powder coating. Manufactured out of ISO 9001, ISO14001 and OSHSAS 18001 certified Plant and product certified for BIFMA performance test .(Size : 2000 x 900 x 650 mm (H)
Supplying and fixing of Mattress (size : 75"x36" x 2" thick) at site, with complete in all respect or as per direction of E/I
Pillow
King Size Bed - Size : 1800L x2000W x 900Ht. construction of bed shall be knock down type in nature. Bed Head Board Made out of 25mm thick Prelaminated Particle Board attach to wall. Bed Box made out of 18 mm thk Prelaminated Particle Board.Mattress Panel and below support Made out of 12 mm thick Prelaminated Particle Board . 50mm x 50mm Solid wood leg with matt polish finish at foot board and lockable castors at headboard side at bottom of bed for maintanance.All exposed edges to be provided with 2.0 mm thick matching grain PVC lipping fixed with hot melt glue.The product is BIFMA and FSC certified
King size Matterss size- 78"x72" with 4" thik Bonded Matterss.
Study Table & Chair Dimension : DESK - 600 W x 480 D x 750 H SEAT - 868 H x 500 W x S 450 Finish/Coating : Powder Coating Material : MILD STEEL TUBULAR SECTION OVAL Tube 35 x 15 SQ. Tube 25x25 and PLB & Moulded wood Total Weight : 23Kg Available Base Frame : Knock down Features : >SEMI KNOCKDOWN > 11 TANK HOT ZINC PHOSPHATING PRE TREATMET PROCESS> Powder Coated The Product should be BIFMA,ISO-9001,ISO-14001 ,OHSAS18001 ,IGBC,FIRA Certified. As Per direction given by E/I.
Wadern's Chamber Table / common room Size: Executive Desk Size - 1800mm (W) x 900mm (D) x 750mm (H) Side Unit - 1800mm (W) x 600mm (D) x 675mm (H) Combination of metal and wood reflects dynamism. Sleek floating top gives aesthetic and trendy look. Open rectanglular section legs with small modesty gives the table trendy, airy open look.
Seat/Back Assembly: The seat is made up of 1.2 ±0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA- P14-18 and upholstered with fabric moulded Polyurethane Foam. The back is made up of 1.2 ±0.1cm hot pressed plywood upholstered with fabric moulded polyurethane foam. The back ply and foam is designed with contoured lumber support for comfortable seating posture. Mid Back Size - 48cm (W) x 64.5cm (H). Seat Size - 51cm (W) x 48cm (D) Armrest (Adjustable): The armrest top is made up of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height is adjustable up to 6.5±0.5cm in 5 steps & also has swivel adjustment of 22° ± 2° on both sides. Knee Tilt Synchro Mechanism with Seat Deapth Adjustment Mechanism: The mechanism is designed with the following features -360° revolving type, Single point control, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 4-position locking with anti-shock feature, Seat back tilting ratio of 1:2 & Seat depth adjustment of 6.0 ± 0.5cm can be locked in 6 positions. Adjustable Backrest: The backrest consists of a sliding up down mechanism, which can be adjusted in the range of 7.5 ± 0.5cm and can be locked in 4 positions for correct position of lumber support. Pneumatic Height Adjustment: The pneumatic height adjustment has an adjustment of 9.0 ± 0.3cm. Pedestal Assembly: The pedestal is fabricated from 0.2 ± 0.2cm thick HR sheet (IS : DD 1079 / HR skin pass), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 66.0±0.5cm Pitch-center dia. (76.0 ± 1.0cm with castors). Twin Wheel Castors: The twin wheel castors are injection moulded in black Nylon.
Visitor Chair-cantiliver chair size (back H-470 *W-460,Seat -D-460*470)mm & mim.Height-430mm. Multipurpose fixed cantiliver chair & armest with pading 7 metal base. A 14mm thick, BWR grade plywood (IS:303) is used to make the seat and back. Deep cushioned back and seat confirm to body contours for proper aligment, posture and all day comfort 5% post consumed recycled content & 30% total recycle content. The Product should be BIFMA. Green guard, AGSI Certifide, ISO 14001, ISO 50001:2011 Certified. Color- Black.
Cantilever chair-chair size (w)595 mm x (D)510 mm x (H)875mm multi purpose fixed chair metal frame PU padding on armrest. Cushion upholstery in leathere with four leg metal legs with matt finish. The product should be BIFMA Green Guard AGSI Certified ISO 50001:2011 Certified. Color- Black.
4 Door Glass Book Case L-900 mm x D-450 mm x H-2000mm Bookcase 4 doors with cam. Body-22 gauge Doors 20 gauge made of mild steel with powder coated
Dining table(3'x3')Table time out 4 seater Size: 900x900x750mm :- Work surface 25 m.m. Thick M D F Board P U painting Under Structure of Ms. Powder Coted Pipe dia 38 mm. The Product should be BIFMA( Original) and IGBC Certified as Per direction given by E/I.
DINING TABLE Work Surface: 25mm Thick (±1mm) Base Material - 25mm MDF Board on top PU painting of Minium 2H hardness with 75% glass as per color chart, combination color graphics on the centre. Color as per color chart. Brown laminate on bottom. Specially profiled edge for comfort. Understructure: Bend pipe understructure of MS. Powder Coated. Pipe dia. 38mm, 2mm thk. Understructure fitted with top by SS machine screws. Legs: MS Powder coated legs for PU top & SS legs for membrane top. 38mm dia pipe legs are fixed with understurcture and table top. Glide: Plastic Glide fixed at the understructure to prevent the damage of table top druing stacking. Size: Ground Base - 2450mm (L) x 1175mm (W). Surface Top - 2400.8mm (L) x 1050.4mm (W) & Height - 750mm (H)
DINING SEAT Seat/Back: Seat & Back are injection moulded in PP. They are snap fitted on the understructure assembly and fixed with self-taping screws Approx. Back Size : 37.0cm (W) x 25.5cm (H) Approx. Seat Size : 40.5cm (W) x 40.5cm (D) Understructure Assembly: The understructure assembly is a welded frame assy
Providing and fixing steel body stool size top 300mm dia and height 750mm with all complete job .The Product should be BIFMA,( Original) and IGBC Certified as Per direction given by E/I.
3 sector chair (Chrome) Made of Cushion with high density cold cured self -skinned pre -molded foam of 50-60 density the shape of plywood. Upholstery is done by using high-pressure pneumatic spray glue and pneumatic press over crome base & legs etc. all complete as per direction of E/I
ELECTRICAL WORKS
Supplying and fixing following ways, surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amp tinned copper bus bar, common neutral link, earth bar, din bar, for mounting MCB's (but without MCB's and incomer) as required. (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)
S/F Electronics Musical call bell suitable for D.C/A.C. single phase 230 copmplete as required.
Supplying and drawing following pair 0.5 sq. mm FR PVC insulated annealed copper conductor, unarmoured telephone cable in the existing surface/ recessed PVC conduit as required.
Rottary Handle
Supply and fixing panel mounted digital multimeter (Voltmeter & ammeter) including CT coil and RYB pilot indictor in the existing cubical panel board including drilling holes in the panel board making connections etc as required.
Providing and fixing H.T. danger notice plate of 250 mm X 200 mm, made of mild steel at least 2 mm thick, vitreous enameled white on both sides, and with inscription in single red colour on front side as required.
P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.
P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)
Supply, installation, testing and commissioning of Silent Type diesel generating set comprising of M&M make engine CPCB IV Model 126 BHP @ NTP , 1500 RPM Coupled to 100 KVA LEYROMER 3 PHASE 415 VOLT ,50 HZ Alternator mounted on acommon base frame along with other accessories i.e. fuel tank AMF CONTROL PANEL, BATTERY WITH LEADS AND ACOUSTIC ENCLOSURE
Supply, installation, testing and commissioning of 100 kVA, Fully Copper(Level-2) 11kV/433V, 3 phase, 50 Hz, Delta star, DYn11, ONAN transformer with Off load tap changer from +5% to -10% in steps of ±2.5%, class F insulation, complete with WTI and scanner for alarm & trip, unidirectional rollers, cable end box for termination of HT cables & Bus duct for LT side complete with rating and technical name plate, earthing terminals with lugs, lifting lugs in all respect with all necessary standard accessories and as per IS. The transformer shall have suitable enclosure for providing neutral CT on earthed star point with connector for connection to REF relay provided in Main panel. All routing test as per IS shall be conducted on the transformer. The Transformer Enclosure shall have suitably designed Louvers for Air Circulation & efficient Cooling. The enclosure shall be Epoxy Powder coated. The transformer shall be subjected to all routine tests as per IS/IEC standards. Type test certificate shall be submitted. The transformer shall meet latest ECBC requirments.Make-Servokon / Schnneider/ Siemens/Powerstar/Infra Power/C&S etc of Higher grade.(Electrical Inspector Charges included)
11 KV DOUBLE POLE STRUCTURE:- Supply, erection, testing and commissioning of 2 pole structure for providing 1 No. 11KV,400A GOS in accordance with IE rules, & local authority specification and drawings and comprising of the following items below.
Design, Supply, Installation, Testing and Commissioning of 20 KW Solar System with all below items. (Approved OEM)
Supply, Installation, Testing and Commissioning of on grid Solar Photovoltaic Power Plant conforming to MNRE specifications as amended, consisting of Mono/Poly Crystalline silicon solar cells, net metering facility, necessary protections, earthing, mountedon Aluminium/GI structure of suitable strength with following components complete as required:-a)Solar Photovoltaic Module of capacity 330Wp or above, manufactured in India, conforming to IS14286/ IEC61215, IS/IEC61730-Part-1, IS/ IEC61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less than16.5%. PV modules used in solar power plants/systems must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% attheend of 25 years. b)Power Conditioning Unit (PCU) of 350-800V DC Input voltage range and 400V AC, three phase, 4 wire, 50Hz+/-2.5Hz, output voltage suitable to generate AC Power with efficiency not less than 97%, total harmonic distortion less than3% and suitable for ambient temperature from 0 to 50 degreeC. The PCU shall adjust the voltage and frequency level to suit the Grid Voltage Frequency. c) Data Monitoring System complete with accessories. d)Fixing of Array junction box & Main junction box with IP65 protection and termination arrangement for incoming and outgoing cable along with glands, lugs and other accessories etc. as required. e) Lightning and surge voltage protection. f) Connections & Interconnections by supplying & fixing required size XLPE insulated copper conductor 1.1kV grade armoured power and control cables between solar modules, main power cable to grid supply PCU unit along with supplying & fixing of necessary channel/conduit lugs and other accessories etc. as required. (Make-TATA/ADANI/WAREE/VIKRAM etc Note:-All Electricals & Mechanical items included.
CCTV Network Camera Dome 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264/MJPEG/H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T
CCTV Network Camera Bullet 4 MP (Brand - Hikvision / Bosch / Honeywell) Image Sensor - 1/3" Progressive Scan CMOS, Shutter Speed - 1/3s to 1/10,000 s, Lens - 2.7mm, 4mm, 6mm @ F2.0angle of view: 106°(2.7mm), 83°(4mm), 55.4°(6mm), Day &Night - IR cut filter with auto switch, White Balance - Automatic/Manual, Video Compression - H.264 /MJPEG /H.264+, Max. Resolution - 2688×1520, Communication Interface - 1 RJ45 10M/100M Ethernet port, Base T
Display : Screen size – 42 inch or above(LG/Sony/Samsung/ Philips), Panel Technology IPS, Surveillance Monitor
Supply / Installation and Commissioning of 24 Port Network Switch GIGA PoE,IEEE 802.3at and IEEE 802.3af Power over Ethernet (PoE) compliant,24x10/100/1000 Mbps Auto-MDIX PoE ports,Provides up to 30 watts per PoE port,PoE power budget 370W,4 KV surge protection for PoE ports,IEEE 802.3x flow control support,Plug-and-play installation,8.8 Gbps switching fabric,2.75 Mbits RAM Data Buffer,4K MAC address entries,Sturdy metal enclosure
Supply Installation Testing & Commissioning of IP Video Storage device shall be a Min 30 days recording,Min RAID-3 protected, all-in-one recording for network surveillance systems It shall be designed for high speed, high capacity Network video storage and high performance play back applications.The video storage array shall have Min 5 internal HDDs (4 x 10TB) Min 4 TB. The storage array shall provide an audible alarm to notify the user in the event of a failure. The system should be such that the vedio recording from camera should be done directly on storage array and directions of Engineer-in-charge. LED indicators Features trayless hard drive insertion Dissipates heat efficiently with aluminum housing. Software configuration if any.Complete in all respects.
Supply fitting fixing Rack 19" 12U fully powder coated complete etc as required with complete accessories (5 amp x 6 socket, wire manager, rack fan) VALRACK/ Netrack make. Wit all necessary items.
ABC Powder Type (Stored Pressure) Fire Extinguisher, 4Kg. Capacity, ISI Mark (IS:15683), squeeze grip valve, operating temperature (+5)° C to (+55)° C for Class 3A type of Fire filled with MAP ABC Powder, Complete in all respect. (Guaranty/Waranty must not be less than 5 years) MAKE:-KALPEX/CEASEFIRE/LIFEGUARD/SAFEAXE etc of Higher grade.
CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683), squeeze grip valve, operating temperature (-30)° to (55)° C for Class 13B type of Fire fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.(Guaranty/Waranty must not be less than 5 years) MAKE:-KALPEX/CEASEFIRE/LIFEGUARD/SAFEAXE etc of Higher grade.
32 bit microprocessor based Intelligent Addressable Fire Alarm Control panel with 4 loops with battery back up. The panel would be modular, decentralized, with The panel shall be consisting with minimum 240 character LCD display and for networking. The Panel would be able to record atleast 60,000 events history. Each loop would be capable to have atleast 250 addressable detectors and addressable devices with up to 3.5km loop length. Make: Schrack Seconet (Vds approved)
1 KVA LINE INTERACTIVE UPS WITH 30 MIN BATTERY BACK UP
Supplying and fixing Intelligent Addressable type multicriteria detector with base for use as heat or smoke or combined both with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.
Supplying and fixing Intelligent Addressable type Smoke/Heat detector with base with automatic electronic addressing, microprocessor type with builtin integrated short circuit isolator including testing, commissiong etc as reqd.
Sypplying and fixing Intelligent Addressable Manual Call Point having inbuilt short circuit isolator i/c testing and commissiong etc as reqd.
Addressable sounder with interface module, power supply for sounder and programmable by software having integrated short circuit isolator & having operating temperature -10⁰C to + 55⁰C
Analogue Addressable Monitor module with IP66 casing containing four relay inputs, each containing a potential-free DPDT contact with a fail-safe and in-built short circuit isolator The ambient temperature range shall be -20C to +60C.
4"/4" JB for mounting of detectors & other accessories with necessary fittings
Supplying and fixing Outdoor Electronic Sounder with 4 distinct tone including 40W Speaker with required accessories as reqd.
Supplying and laying of 2x1.5 sq.mm. ISI marked copper armourd conductor cable with gland scoket and other wiring accessories on the existing surface/tray/shaft etc as reqd
Providing and fixing M.S. pipe to I.S. 1239 (Heavy class) complete with all supports & fittings like, unions, couplings, bends, elbows, tees, offsets,reducers, flanges as per table 'E' etc. to complete the work as per the requirement at site including painting with one coat of primer after surface preparartion and two coats of synthetic enamel paint, cutting and making good the walls good complete. Pipe upto 40 mm dia threaded joints with holdtite, 50 mm dia and above should be welded joint ( all type) (internal works/External Works).
Providing & Fixing dust and Verin proof motor control panel fabricated with 14 SWG MS sheet with stove enamelled paint and comprising of Fire Pump.
Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as
Providing and fixing first aid fire hose reel drum wall mounting, swinging type(Powder coated finish in fire red) fitted with 20 mm dia. 30 m long high pressure hose(IS:444, Type-2) with 5 mm outlet SS nozzle with shut off valve (IS:8090). complete hose reel drum shall be conforming to IS:884) 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle.Drum and brackets for fixing the equipmets on wall.
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :
Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :
Code. SOR-2020
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work upto plinth level.
1.4.8 (1 Cement :4 coarse sand :8 graded stone agregate 40 mm nominal size)
per 50 kg cement
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work
Extra tor Brick work in superstructure above plinth level upto floor V cum
250 mm th Brick work in C.M (1:6)
125 mm th Brick work in C.M (1:4)
Providing and fixing to existing door frames.
Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm,made out of extruded 5 mm rigid PVC foam sheet, mitred at corners and…
Providing and fixing aluminium sliding door bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete:
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ), transparent or dyed to required colour or shade, with necessary screws etc. complete:
Providing and fixing aluminium hanging floor door stopper anodized (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade with necessary screws etc. complete.
Providing and fixing ISI marked steel wire gauged doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs, 10 cm long , embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using galvanized M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm with 12 mm mild steel beading complete including applying a priming coat of approved steel primer, but excluding the cost of other fittings except necessary hinges or pivots as required
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations, of required size,approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
With ready mixed red oxide zinc chromate yellow primer of approved brand and manufacture on steel galvanized iron/steel works
Forming groove of uniform size from 12 x 12 mm and upto 25 x 15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-charge.
Finishing walls with Acrylic Smooth exterior paint of required shade :
1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.
IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.
IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area.
IVth course of 400 micron thick PVC sheet (overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm
With average thickness of 120mm and minimum thickness at Khurra as 65 mm.
Providing plinth protection 750 mm wide consisting of 12 mm thick cement plaster 1;6 with neat cement punning over 75 mm thick P.C.C. (1:3 :6) over brick flat soling over 75 mm thick local sand filling all complete
Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement : 2 coarse sand ) to match the existing floor.
Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,
Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.
Bricks (lead - 1 km kutcha + 7 km pucca)
Coarse Sand (Lead- 140 km) Kiul
Stone Chips (Lead- 240 km) Manpur Gaya
Local sand (1 km kutcha + 2 km pucca)
Cement
Bricks
Providing and fixing water closet squatting pan (Indian type W.C.pan with 100 mm sand cast Iron P or S trap, 10 litre low fixtures complete, including cutting and making good the walls andlevel white P.V.C. flushing cistern, including flush pipe, with manually controlled device handle lever conforming to IS : 7231, with all fittings and floors wherever required :
Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS : 13983 with C.I. brackets and stainless steel plug 40 mm,including painting of fittings and brackets, cutting and making good the walls wherever required :
Sand cast iron S&S pipe as per IS: 1729
114 mm off sets
152 mm off sets
Providing and fixing terminal guard :
Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron pipes and fittings of diameter :
Providing and fixing trap of self cleansing design with screwed down orhinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :
Providing and fixing PTMT Waste Coupling for wash basin and sink,of approved quality and colour.
150 mm nominal size square 100 mm diameter of the inner hinged round grating
With common burnt clay F.P.S. (non modular) bricks of class designation 7.5
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg)
Septic Tank - 2 Nos. x @ Rs. 3,24,501/- 6.6 mtr (long) x 2.80 mtr (wide) x 1.40 mtr (deep) {of inside finished size as per design & drawing
Providing and fixing on wall face unplastidsed-PVC(working pressure 4 kgf per sqm) rain water pipes conforming to IS :4985 including jointing with seal ring conforming to IS: 5382 leaving 10 mm gap for thermal expansion.
Supplying,installing,testing and commissioning submersible pump 2HP with stater & wire of necessary length
Construction of subgrade and Earthen Shoulder (Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts & leads, transporting to site, spreading, grading to required slope an compacted to meet requirement of table No. 300-2)
Compacting original ground Compacting original ground supporting subgrade (Loosening of the ground upto a level of 500 mm below the subgrade level, watered, graded and compacted in layers to meet requirement of table 300-2 for subgrade construction)
Supplying and Filling with local sand and under floors including, watering, ramming consolidating and dressing complete.
Providing designation 100 A one brick flat soling joints filled with local sand including cost of watering taxes, royalty all complete as per building specification and direction of E/I.
Providing designation 100 A one brick on edge soling joints filled with local sand including cost of watering, taxes, royalty all complete as per building specification and direction of E/l,
Edges of slabs and breaks in floors and walis- Under 20 cms wide
Cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size) in pavements, laid to required slope and camber in panels as required including consolidation finishing and tamping complete.
Bricks (lead - 1 km kutcha + 7 km pucca)
Coarse Sand (Lead- 140 km) Kiul
Stone Chips (Lead- 240 km) Manpur Gaya
Local sand (1 km kutcha + 2 km pucca)
Earth
Cement
Bricks
Lintels, beams, plinth beams, girders, bressumers and cantilevers with water proof ply 12 mm thick
Columns, Pillars, Piers, Abutments, Post and struts
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
All work upto plinth level
All work from plinth level upto floor V level.
Brick work with fly ash bricks as per IS 12894(2002) & IS 3495 in foundations and plinth in :
Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work
Extra tor Brick work in superstructure above plinth level upto floor V cum
Forming groove of uniform size from 12 x 12 mm and upto 25 x 15 mm in plastered surface as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repairs to the edges of plaster panel and finishing the groove complete as per specifications and direction of the Engineer-in-charge.
Labour for cutting of M.S. angle iron post to required length, one end splitted as fish tailed in a length of 150mm complete as per building
Earth Work in filling in campus with ordinary soil vide classfication of soil (item-A) obtained from borrow pits or any other ingradients likely to detoriate effect the stability of the embankment including breaking the clods maximum to 60mm cube placing the earth in layers not exceeding 225mm in loose thickness, rough dressing including cost of cutting and removing shrubs roots falling in borrow area all complete as per approved design, specification and direction of E/I. (Lead-1 Km kutcha + 1 km pucca)
Bricks (lead - 1 km kutcha + 7 km pucca)
Coarse Sand (Lead- 140 km) Kiul
Stone Chips (Lead- 240 km) Manpur Gaya
Local sand (1 km kutcha + 2 km pucca)
Cement
Bricks
Bed Dimension : 1950 x 900 x 650 mm (H) Structure is made up of 40 mm dia CRC tube with thickness 18 gauge. Horizontal base is made from steel sheet the thickness 14 gauge. Horizontal base will be stiffened with appropriate longitudinal 3 v shape sheet and lateral stiffeners 2 steel pipes with powder coating. Manufactured out of ISO 9001, ISO14001 and OSHSAS 18001 certified Plant and product certified for BIFMA performance test .(Size : 2000 x 900 x 650 mm (H)
Supplying and fixing of Mattress (size : 75"x36" x 2" thick) at site, with complete in all respect or as per direction of E/I
Pillow
King Size Bed - Size : 1800L x2000W x 900Ht. construction of bed shall be knock down type in nature. Bed Head Board Made out of 25mm thick Prelaminated Particle Board attach to wall. Bed Box made out of 18 mm thk Prelaminated Particle Board.Mattress Panel and below support Made out of 12 mm thick Prelaminated Particle Board . 50mm x 50mm Solid wood leg with matt polish finish at foot board and lockable castors at headboard side at bottom of bed for maintanance.All exposed edges to be provided with 2.0 mm thick matching grain PVC lipping fixed with hot melt glue.The product is BIFMA and FSC certified
King size Matterss size- 78"x72" with 4" thik Bonded Matterss.
Study Table & Chair Dimension : DESK - 600 W x 480 D x 750 H SEAT - 868 H x 500 W x S 450 Finish/Coating : Powder Coating Material : MILD STEEL TUBULAR SECTION OVAL Tube 35 x 15 SQ. Tube 25x25 and PLB & Moulded wood Total Weight : 23Kg Available Base Frame : Knock down Features : >SEMI KNOCKDOWN > 11 TANK HOT ZINC PHOSPHATING PRE TREATMET PROCESS> Powder Coated The Product should be BIFMA,ISO-9001,ISO-14001 ,OHSAS18001 ,IGBC,FIRA Certified. As Per direction given by E/I.
Wadern's Chamber Table / common room Size: Executive Desk Size - 1800mm (W) x 900mm (D) x 750mm (H) Side Unit - 1800mm (W) x 600mm (D) x 675mm (H) Combination of metal and wood reflects dynamism. Sleek floating top gives aesthetic and trendy look. Open rectanglular section legs with small modesty gives the table trendy, airy open look.
Seat/Back Assembly: The seat is made up of 1.2 ±0.1cm thick hot pressed plywood measured as per QA method described in OCP-QLTA- P14-18 and upholstered with fabric moulded Polyurethane Foam. The back is made up of 1.2 ±0.1cm hot pressed plywood upholstered with fabric moulded polyurethane foam. The back ply and foam is designed with contoured lumber support for comfortable seating posture. Mid Back Size - 48cm (W) x 64.5cm (H). Seat Size - 51cm (W) x 48cm (D) Armrest (Adjustable): The armrest top is made up of moulded polyurethane (P.U) and mounted on to a drop lift height adjustable type M.S. tubular armrest support chrome plated. The armrest height is adjustable up to 6.5±0.5cm in 5 steps & also has swivel adjustment of 22° ± 2° on both sides. Knee Tilt Synchro Mechanism with Seat Deapth Adjustment Mechanism: The mechanism is designed with the following features -360° revolving type, Single point control, Front pivot for tilt with feet resting on ground ensuring more comfort, Tilt tension adjustment, 4-position locking with anti-shock feature, Seat back tilting ratio of 1:2 & Seat depth adjustment of 6.0 ± 0.5cm can be locked in 6 positions. Adjustable Backrest: The backrest consists of a sliding up down mechanism, which can be adjusted in the range of 7.5 ± 0.5cm and can be locked in 4 positions for correct position of lumber support. Pneumatic Height Adjustment: The pneumatic height adjustment has an adjustment of 9.0 ± 0.3cm. Pedestal Assembly: The pedestal is fabricated from 0.2 ± 0.2cm thick HR sheet (IS : DD 1079 / HR skin pass), chrome plated and assembled with injection moulded black polypropylene hub cap and 5 nos. twin wheel castors. The pedestal is 66.0±0.5cm Pitch-center dia. (76.0 ± 1.0cm with castors). Twin Wheel Castors: The twin wheel castors are injection moulded in black Nylon.
Visitor Chair-cantiliver chair size (back H-470 *W-460,Seat -D-460*470)mm & mim.Height-430mm. Multipurpose fixed cantiliver chair & armest with pading 7 metal base. A 14mm thick, BWR grade plywood (IS:303) is used to make the seat and back. Deep cushioned back and seat confirm to body contours for proper aligment, posture and all day comfort 5% post consumed recycled content & 30% total recycle content. The Product should be BIFMA. Green guard, AGSI Certifide, ISO 14001, ISO 50001:2011 Certified. Color- Black.
Cantilever chair-chair size (w)595 mm x (D)510 mm x (H)875mm multi purpose fixed chair metal frame PU padding on armrest. Cushion upholstery in leathere with four leg metal legs with matt finish. The product should be BIFMA Green Guard AGSI Certified ISO 50001:2011 Certified. Color- Black.
4 Door Glass Book Case L-900 mm x D-450 mm x H-2000mm Bookcase 4 doors with cam. Body-22 gauge Doors 20 gauge made of mild steel with powder coated
Dining table(3'x3')Table time out 4 seater Size: 900x900x750mm :- Work surface 25 m.m. Thick M D F Board P U painting Under Structure of Ms. Powder Coted Pipe dia 38 mm. The Product should be BIFMA( Original) and IGBC Certified as Per direction given by E/I.
DINING TABLE Work Surface: 25mm Thick (±1mm) Base Material - 25mm MDF Board on top PU painting of Minium 2H hardness with 75% glass as per color chart, combination color graphics on the centre. Color as per color chart. Brown laminate on bottom. Specially profiled edge for comfort. Understructure: Bend pipe understructure of MS. Powder Coated. Pipe dia. 38mm, 2mm thk. Understructure fitted with top by SS machine screws. Legs: MS Powder coated legs for PU top & SS legs for membrane top. 38mm dia pipe legs are fixed with understurcture and table top. Glide: Plastic Glide fixed at the understructure to prevent the damage of table top druing stacking. Size: Ground Base - 2450mm (L) x 1175mm (W). Surface Top - 2400.8mm (L) x 1050.4mm (W) & Height - 750mm (H)
DINING SEAT Seat/Back: Seat & Back are injection moulded in PP. They are snap fitted on the understructure assembly and fixed with self-taping screws Approx. Back Size : 37.0cm (W) x 25.5cm (H) Approx. Seat Size : 40.5cm (W) x 40.5cm (D) Understructure Assembly: The understructure assembly is a welded frame assy
Providing and fixing steel body stool size top 300mm dia and height 750mm with all complete job .The Product should be BIFMA,( Original) and IGBC Certified as Per direction given by E/I.
3 sector chair (Chrome) Made of Cushion with high density cold cured self -skinned pre -molded foam of 50-60 density the shape of plywood. Upholstery is done by using high-pressure pneumatic spray glue and pneumatic press over crome base & legs etc. all complete as per direction of E/I
Wiring for light point/fan point/exhaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit, with modular type switch, modular plate, suitable size G.I. box and earthing the point with 1.5 sq.mm. FR PVC insulated copper conductor single core cable etc.as required
Supplying and fixing PVC/G.I box of 200mm x 250mm x 60mm deep on surface or in recess with suitable size of phenolic laminated sheet cover in fornt including painting etc as required.
Supplying and fixing modular type 2 pin telephone socke/ speaker outlet on the existing modular plate & box including making connection,excluding moduler plate etc. as required.
Supplying and fixing modular T.V antenna socket on the existing modular plate and metal box including making connection, etc. as required.
Supply & fixing 2+ 8 way double door SP & N, sheet steel, MCB distribution board, 240 volts, on surface/ in recess, complete with tinned copper busbar, neutral link, earth bar, din bar, detachable gland plate, interconnections, phosphatised and powder painted including earthing etc.as required (But without MCB / RCCB / Isolator) Lighting DB
Supply and fixing 320 A 4 Pole on load / panel moumted change over switch in existing cubical panel board making connection, earthing the body etc.as required
Supplay and fixing wall /floor mounted cubicle panel board fabricated with 16 gauge iron sheet suitable for panel mounted switch discconnector including Bus bar chamber insulator and painting etc as required.9but without bus bar copper strip)
S/F digital voltmeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.
S/F digital ammeter three phase existing cubicle panel board including drilling holes in the panel board making connection etc.
Supply and Installation of regular/standard module AC ceiling fan of 1400 mm sweep including wiring the down rod of standard length 9 upto 30 cm ) with 1.5 sq mm FR pvc insulated copper conductor etc as required.
Supply and Installation of 300 mm 230volt AC exhaust fan in the existing opening including making good the damage connection testing commissioning etc as required.
Supplying and fixing recess/surface mounted 23/24 (1ft X 1ft) watt LED downlighter complete with integrated electronic driver & LED directly on ceiling/false ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.
SSupplying and fixing single wall mounted 9/10 watt (2 ft long) LED type batten fitting complete with electronic driver and LED etc directly on wall/ ceiling including connections with 1.5 sq.mm FR PVC insulated copper conductor and earthing the body etc. as required.
Supplying and fixing 90 watt LED type street light with die cast aluminium housing for ingress protection of IP65 and complete with all accessories etc, on pole/building including connection with FR PVC insulated copper conductor cable and earthing the body etc. as required.
P/F lightning conductor final, made of 25mm dia. 300mm long, copper tube having single pron on top with 85 mm dia 3 mm thick copper base palte including holes etc complete as required.
P/F copper tape 20mmx3mm thick on parapet or surface of wall for lighting conductor complete as required ( for vertical run)
Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size
3KVA on grid solar pannel set complete with battary,solar plate,cable for plate to solar pannel etc. with 4hr back up.
Supply and Installation of Indoor Dome IR Network Camera (1/2.7" CMOS sensor, Mini. Pixel of 2560*1920 or higher video quality, frame rate of Up To 25fps @ 5MP, H.265, H.264 & MJPEg video compression, 2.8mm Fixed lens, physical ICR filter of both day and night, 30mtr IR Distance,120dB WDR ,3Streams Supported, WDR , 3D-DNR for noise reduction, BLC, ICR, EXIR, Audio In and Out, Alam in and Out. IPv4/IPv6 network supported, IP67, IK10 rated for weatherproofing, ONVIF ver 2.2 or higher, PoE IEEE 802. 3af (UL, FCC, CE, BIS certified.). Make Hikvision/Bosch/Honeywell
Supply and Installation of outdoor Bullet IR Network Camera 1/2.7" CMOS, ICR, 2592*1944@ 25fps, 5 MP H.265/H.264/MJPEG, Triple streams, DC12V & PoE, Micro SD card slot up to 256 GB, Alarm in/out , Audio 1/1, IP67, 2.7-13.5mm Motorized Varifocal lens, IR anti-reflection window, Built-in bracket, IR range: up to 50m, Digital WDR Range, 3D-DNR for noise reduction, Audio In and Out, Alam in and Out IPv4 network supported, IP67 rated for weather proofing, ONVIF, POE IEEE 802.3af, (UL, FCC, CE, BIS certified). Make-Panasonic/ Bosch/Honeywell
Supply, installation, testing and commissioning of all-in-one recording solution for up to 16 to 32 channels, Pre-installed, pre-configured IP storage solution with 8-16 TB storage capacity, RAID-5 protected,Hot-swappable hard drives,Intel Xeon Quad Core X3430 (2.4 GHz, 8 M Cache, 95 W) Processor,4-8 GB memory installed, 2U rack mount, Temperature +10 °C to +35 °C, Relative humidity-8 to 90% (non-condensing), CE, UL Certified. Recording shall be calculated for all cameras at full frame rate & resolution for upto 15 days .with Intel i5 processor, 4-32GB RAM, 2TB HDD, 2-4 GB Dedicated NVidia Graphics card, Windows 7-10 or as recommended by VMS Software. The Workstation shall be suitable for any open platform software as required as per specification. . MAKE - Bosch / PELCO/ ONCAM
32" Full HD LED Professional Display for Monitoring with mounting accessories.
Layer 2 networking switch, 24 # 10/100/1000 BT ports, PoE as per 802.3a/f with 2 Nos of Fiber interface ports.
Supplying and laying of SOLID CABLE, CAT6 UTP, 4PAIR, 23AWG, LSZH CM,BLUE colour through existing conduit /trunk complete as required & as per Direction of Engineer-In-Charge.MAKE : DIGISOL/DIGILINK
19" 6U Rack for Switches complete as required
3x3 Juncation box with face place complete for Camera
Supplying of XLPE/PVC insulated Sheathed (Heavy Duty) armoured electric cable with aluminium conductor of 1.1 KV graded con. IS 1554 Part I upto date amendment etc as required of following size
ABC Powder Type (Stored Pressure) Fire Extinguisher, 4 kg. Capacity, ISI mark (IS:15683), squeeze grip valve, operating temperature (+5) degree Celcuis to (+55) dgree Celcuis for Class 3A Type of Fire Filled with MAP ABC Powder, Complete in all respect
CO2 Type Fire Extinguisher, 4.5 Kg Capacity, ISI Mark (IS:15683) squeeze grip valve, operating temperature (-30) deg Cel to (55) deg cel. For Class 13B type of Fire Fitted with 1 Mt. Hose & PVC Horn, Complete in all respect.
BSBCCL
DARBHANGA
Code. SOR-2022
TMTC-500- 8mm dia .
TMTC-500-10 mm dia.
TMTC-500-12 mm dia.
TMT FE-500-16 mm dia.
TMT FE-500-20 mm dia.
TMT FE-500-25 mm dia.
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
All work upto plinth level
Providing and laying in position machine batched, machine mixed and machine vibrated design mix cement concrete of specified grade for reinforced cement concrete structural elements, excluding the cost of centring, shuttering, finishing and reinforcement, M-20 grade reinforced cement concrete
All work from plinth level upto floor V level. Walls, columns, pillars, posts and struts
Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work
Cement mortar 1:6 (1 cement: 6 coarse sand ) - 250 mm th Brick work Up to PL
Half brick Masonary Cement mortar 1.:4 (1 cement: 4 coarse sand ) - 125 mm th Brick work
Extra tor Brick work in superstructure above plinth level upto floor V cum
Providing and fixing factory made uPVC white colour sliding glazed window above 1.50 m in height dimension comprising of uPVC multichambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads, uPVC extruded interlocks and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle on one side of extreme panel along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) touch lock with hook (if required for wire mesh panel), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable.
Two track two panels sliding window made of (big series) frame 67 x 50 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 2.50 sqm upto 4.00 sqm.)
Providing and fixing ISI marked steel wire gauged doors, windows and ventilators of standard rolled steel sections, joints mitered and welded with 15x3 mm lugs, 10 cm long , embedded in cement concrete blocks 15x10x10 cm of 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) or with wooden plugs and screws or rawl plugs and screws or with fixing clips or with bolts and nuts as required, including providing and fixing fly proof galvanized M.S. wire gauge to windows and clerestory windows using galvanized M.S. wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm with 12 mm mild steel beading complete including applying a priming coat of approved steel primer, but excluding the cost of other fittings except necessary hinges or pivots as required
25 kg/sqm
20kg/sqm
Providing and applying white cement based putty of average thickness 2 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
1st course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface.
IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface.
IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg per sqm of area.
IVth course of 400 micron thick PVC sheet (overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm
n*l*b+(l+b)*2*n*h
Providing plinth protection 750 mm wide consisting of 12 mm thick cement plaster 1;6 with neat cement punning over 75 mm thick P.C.C. (1:3 :6) over brick flat soling over 75 mm thick local sand filling all complete
Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm. Clear depth and 250mm apron including cost of E/W. involved with 75mm cement concrete (1:4:8) over one brick designation 100-A flat soling in proper grade and slope at the base.the drain duly.plastered in CM. (1:3) with punning over exposed surface all complete as per building specification and direction of E/l,
Providing well burnt brick bats or Jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blinding the top with cement mortar (1:10) all complete as per building specification and direction of E/I.
Bricks (lead - 1 km kutcha + 7 km pucca)
Coarse Sand (Lead- 139 km)
Stone Chips (Lead- 220 km)
Local sand (1 km kutcha + 2 km pucca)
Cement
Bricks
BSBCCL
DARBHANGA
Description of Work
Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the likes
Clearing jungle including uprooting of rank vegetation ,grass, brush wood, trees and saplings of girth upto 30 cm measured at a height of 1 m above ground level and removal of rubbish upto a distance of 50 m outside the periphery of the area cleared.
Coarse Sand
Stone Chips
Bricks
Local Sand
Cement
Carriage cost of Earth
BUXAR
Item of Work
Particulars
Boring, Providing and installing cast in situ single under reamed piles of specified diameter and length below pile cap in M-25 cement concrete, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the cost of boring with bentonite solution and the length of the pile to be embedded in pile cap etc. all complete. (Length of pile for payment shall be measured upto to the bottom of pile cap) :
Area vide Item no. 14
Area vide Item no. 15
BUXAR
Item of Work
PROJECT :- PROPOSED Construction of 100 Beded Ambedkar Boys Hostel SC-ST AT Campus Of Bipin High School in Dist- West Champaran
Name of Item
Rs (in Lakh)
Rs (in Lakh)
Rs (in Lakh)
aoc.json
Purchase Order
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
NIT-78 Gr01.pdf
NIT • 1.51 MB
BOQ Bipin High School final.xls
NIT • 1.09 MB
CHECK LIST FOR CONTRACTORS.pdf
NIT • 1.76 MB
JVG.pdf
NIT • 1.20 MB
NIT-78 Gr01.pdf
NIT • 1.51 MB
84806_SBD_Bipin High School final (1).doc
NIT • 10.69 MB
BOQ Bipin High School final.xls
NIT • 1.09 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .