Loading
Loading…
Loading…
Tender Value
₹69.3 L
EMD Value
₹1.4 L
Closing Date
2 Sept 2026, 3:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Revenue
P.WAY
14 conditions · 3 needing a document upload
Financial Eligibility Criteria: The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees. N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. (For details refer tender documents)
Similar Nature of Work:- Execution of any P. Way related works.
32 conditions · 2 needing a document upload
The tenderer(s) should submit the BID SECURITY in acceptable form i.e. only through net banking or e-payment gateway or submitted as Bank Guarantee Bond from a Scheduled Nationalized bank of India or as mentioned in the tender documents. The Bank Guarantee Bond shall be as per Annexure- VI(A) and shall be valid for a period of 90 days beyond the bid validity period.( NOTE: For submission of Bid Security in the form of Bank Guarantee, all the procedures mentioned at Para-5 Bid Security (3)(i) to (vii) mentioned in the tender document should invariably be followed.)
Whether History sheet of tenderers (Annexure-2 of Part-II of Tender documents) uploaded duly filled in with supportive documents.
Whether the details of facilities available vis-a-vis the requirements mentioned in STR in a tabular/narrative form if you are not on the approved list of RDSO, if required in the Annexed Document, is submitted.
Whether, EACH PAGE of the copy of documents/certificates in support of credential is self attested/digitally signed by tenderer/authorised representative with signature, stamp & date.
Whether all the documents related "Mandatory Requirement", as applicable and mentioned in the bid documents are enclosed with the tender.
Please submit bank details as per enclosed Annexure-12 of Part - II of Tender Documents or photo copy of a "Cancelled Cheque". (For details refer tender documents)
Please submit Certificate of Familiarisation as per Annexure-1 of Part-II of Tender Documents. (For details refer tender documents)
Please submit required details as required from Annexure 2 to 11 of Part-II of Tender documents duly filled in and signed. Supportive documents/separate sheet are to be submitted, if required. Annex-2: HISTORY SHEET OF THE TENDERER, Annex-3: TECHNICAL EIGIBILITY CRITERIA, Annex-4: DETAILS OF CONSTRUCTIONS MACHINERIES, TOOLS & PLANTS, VEHICLES ETC. AVAILABLE (ON HAND AND PROPOSED TO BE UTILISED, Annex-5: DETAILS OF TECHNICAL AND OTHER PERSONNELS AVAILABLE ON HAND & PROPOSED TO BE ENGAGED. Annex- 6: DETAILS OF WORKS COMPLETED DURING PREVIOUS THREE FINANCAIL YEARS & CURRENT YEAR, Annex-7: DETAILS OF WORKS ON HAND, Annex- 8: DECLARATION REGARDING ASSOCIATION OF RAILWAY OFFICER (S) WITH TENDERER(S), A n n e x - 9 : LIST OF COURT CASES, Annex-10: LIST OF ARBITRATION CASES. Annex- 11: BROAD PLAN FOR EXECUTION OF THIS WORK. (For details refer tender documents)
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
The tenderer shall clearly specify whether the tender is submitted on his own (Proprietary Firm) or on behalf of a Partnership Firm / Company / Joint Venture (JV) / Registered Society / Registered Trust / Hindu Undivided Family (HUF)/ Limited Liability Partnership (LLP) etc. If it is NOT mentioned in the submitted tender that tender is being submitted on behalf of a Sole Proprietorship firm/Partnership firm/Joint Venture/Registered Company etc., then the tender shall be treated as having been submitted by the individual who has signed the tender . The tenderer(s) shall enclose the attested copies of the constitution of their concern and copy of PAN card along with the tender. Tender Documents in such cases are to be signed by such persons as may be legally competent to sign them on behalf of the firm, company, association, trust or society, as the case may be. (for details refer tender documents) NOTE: Any document containing PAN number of the tenderer(s) shall also be considered in lieu of PAN card. However, if no document having mention of PAN number is uploaded, offer will be summarily rejected. (For details refer Tender documents)
For all tenders having advertised cost of Rs.10 lakh or above, the contractor shall have to submit the option to take payment from Railways through a letter of credit (LC) arrangement. The tenderer shall affirm having read over and agreed to the terms and conditions of the LC option. The option of taking payment through LC arrangement, once exercised by tenderer at the time of bidding, shall be final and no change shall be permitted, thereafter, during execution of contract. (The tenderer have to submit the option to take payment from Railway through a Letter of Credit arrangement) (For details refer Tender documents)
The list of personnel / organization on hand and proposed to be engaged for the tendered work. Similarly, list of Plant & Machinery available on hand and proposed to be inducted and hired for the tendered work. (For details refer tender documents)
Documents to be submitted as per Clause 14 of GCC-April 2022 in support of (a)Sole Proprietorship firm (b) HUF (c) Partnership Firm (d) Joint Venture (JV) (e) Company registered under Companies Act 2013 (f) LLP (Limited Liability Partnership) (g) Registered Society & Registered Trust. (for details refer tender documents) NOTE: Non submission of above documents will lead to summarily rejection of the offer.
All repairs and maintenance of P. way zonal works for a period up to 30/09/2027 from Km. 0.00 to 106.650 between KUR(Ex) to DSPL section under the jurisdiction of SSE(P.Way)/NYGT of Khurda Road Division.
e-tendersouthkur-132-2026~ECOR
e-tendersouthkur-132-2026
Open
Works - General
12 Months
Khordha, Odisha
₹0
₹1.4 L
12 Aug 2026
12 Aug 2026
19 Aug 2026
45 items across 3 schedules · ₹50,29,933.46 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Up to 40 m long rail panel | RM | 300.00 | 8.49 | 2,547 |
| 2 | For Casual/Scattered Rail Renewal work | RM | 300.00 | 33.06 | 9,918 |
| 3 | For Casual/Scattered Rail Renewal work | RM | 300.00 | 34.99 | 10,497 |
| 4 | For 1.00m long fishplates | Joint | 100.00 | 102.51 | 10,251 |
| 5 | Opening and refixing of Joggled fish plates provided to weld joints/rail of any rail section under traffic to enable examination of weld/rail by departmental official nominated by Engineer In charge and lubrication of fishplates by applying departmental Grease graphite grade 'O' (IS:408) to fishing planes and bolts by departmental black oil as per procedure laid down in latest version of IRPWM, including all tools required and as directed by Engineer-in- charge. Note: 1. Grease Graphite, black oil, fish bolts, K.Oil, wire brush, required for work shall be given by department and issued at concerned SSE/PW Stores. 2.Jammed fish bolts shall be cut using chisel and hammer and replaced with new bolt. | Set | 100.00 | 48.53 | 4,853 |
| 6 | Lubrication of ERCs and its liner contact area by removal of ERCs and Metal / GFN liners in rail panel, cleaning of rust / scale of ERC, Metal / GFN liners & SGCI insert by using wire brush, scrapper / sand emery paper etc supply and application of graphite grease, as prescribed by Railway for under side of liners & corresponding area of rail foot & SGCI insert with ERCs and re- fixing the same as per procedure prescribed in latest edition of IRPWM with contractors grease and all other tools & plants complete and as directed. Note: Each ERC in this item shall constitute 1 ERC and its Liner Contact area. | ERC | 5000.00 | 4.08 | 20,400 |
| 7 | Sleepers up to 2.85 m length | Each | 200.00 | 563.99 | 1,12,798 |
| 8 | Lifting and packing for regrading the existing PSC sleeper track to required height / level in stages not exceeding 75mm or part thereof at a time, providing permissible ramp for the track, insertion of moorum / sand / stone ballast uniformly under the existing track and placing the same to safe approved gradient, gauge, cushion including levelling and one round of through packing to allow train movement at restricted speed of 30 kmph for a specified length with all leads & lifts and fixing, marking, painting rail level pegs at every 30m interval. Note: Lifting of track shall be done in stages as per procedure prescribed in latest edition of IRPWM to get the proposed final level as per approved working profile, as directed by Engineer in-charge. | TRM | 5000.00 | 165.82 | 8,29,100 |
| 9 | Boxing and profiling of ballast as per procedure prescribed in latest edition of IRPWM including cess dressing on both sides of track. The work will include removing excess ballast from track and putting the same in crib and shoulder by leading to a maximum of 50m including crossing of track, deweeding on ballast section etc and as directed by Engineer-In charge. | TRM | 8000.00 | 24.39 | 1,95,120 |
| 10 | For 60 Kg Rail, Single shot crucible fitted with Automatic Tapping Thimble , 3 pieces Mould (Zircon washed) and Compressed Air Petrol/LPG pre heating technique | Each | 100.00 | 1,882.35 | 1,88,235 |
| 11 | For 52 Kg - 90 UTS or 52 Kg 72UTS Rail, Single shot crucible fitted with Automatic Tapping Thimble Technology, 3 pieces Mould (Zircon washed) and Compressed Air Petrol heating technique. | Each | 50.00 | 1,741.94 | 87,097 |
| 12 | For PSC sleeper Track with Sleeper Density of 1540 Sleepers/Km or more | TRM | 15000.00 | 96.79 | 14,51,850 |
| 13 | 1 in 8½ PSC layout | Set | 2.00 | 10,631.25 | 21,262.5 |
| 14 | 1 in 12 PSC layout | Set | 5.00 | 13,828.92 | 69,144.6 |
| 15 | Packing of isolated loose PSC sleepers on plain track below the bottom of t h e sleepers and surrounding through out its length duly opening two galas on either side of the renewed sleepers and packing the sleeper to bring the track to normal speed including gauging, aligning, squaring of sleepers and sectioning of ballast to the required profile with all contractor's labour, tools and plant etc. including all lead and lift and crossing of tracks where ever necessary complete and as directed by the Engineer-in- charge. | Sleeper | 4000.00 | 75.21 | 3,00,840 |
| 16 | For PSC sleeper Track with Sleeper Density of 1540 sleepers/Km or more | TRM | 500.00 | 164.96 | 82,480 |
| 17 | Without Rail tensor | TRM | 8000.00 | 33.95 | 2,71,600 |
| 18 | With 2 bolts | Set | 50.00 | 102.55 | 5,127.5 |
| 19 | For day time block working | TRM | 10000.00 | 17.66 | 1,76,600 |
| 20 | 52 Kg - 90 UTS - Outside Track | Each | 50.00 | 277.35 | 13,867.5 |
| 21 | 60 Kg - 110/90 UTS - On Running Line | Each | 200.00 | 384.24 | 76,848 |
| 22 | 52 Kg - 90 UTS- On Running Line | Each | 50.00 | 310.55 | 15,527.5 |
| 23 | On Running Line | Each | 200.00 | 68.3 | 13,660 |
| 24 | Manufacture & supply of tested GI wire rope of 6mm dia. and 6 ply to suit lifting barrier gates at nearby P.Way Stores / Depot / Level Crossing gate, as directed. | Kg | 10.00 | 196.85 | 1,968.5 |
| 25 | Manufacture and supply of Hook Bolt 28mm dia. & 320mm long as per RDSO Drg. no. BA- 1636/I/R2 from RDSO approved sources | Kg | 100.00 | 142.93 | 14,293 |
| 26 | Caution Indicator Board of size 1400mmx400mm with back support frame fixed to vertical post of MS angle of size 50mmx50mmx6mm of 3650 mm long | Each | 5.00 | 6,067.76 | 30,338.8 |
| 27 | Speed Indicator Board of equilateral triangular shape having each side of 1000mm with back support frame fixed to vertical post of MS angle of size 50mmx50mmx6mm of 3650 mm long | Each | 5.00 | 5,205.56 | 26,027.8 |
| 28 | Termination Indicator Board of Circular shape having diameter of 1000mm with back support frame welded to vertical post of MS angle of size 50mmx50mmx6mm of 3950 mm long | Each | 6.00 | 7,362.86 | 44,177.16 |
| 29 | Manufacturing, supplying and fixing Curve Indicator / Point Indicator / SEJ Boards to be provided at various locations on formation, made out of MS sheet 2mm thick of size 450mm x 300mm duly fixed with MS frame of 25mm x 25mm x 3mm angle welded to 50mm x 50mm x 3mm MS angle, 1000mm long post split and bent 100mm at bottom end with all lead & lift as per specification and including painting of details with enamel paint, as directed by Engineer in-charge (Earthwork & concreting will be paid separately) | Each | 60.00 | 1,066.15 | 63,969 |
| 30 | 7.2 mm dia. | Each | 10.00 | 464.74 | 4,647.4 |
| Schedule total | ₹41,55,045.26 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
.Splcondofcontract-I.pdf
ATTACHMENT
.Splcondofcontract-II.pdf
ATTACHMENT
eTender conditions
ATTACHMENT
Spl cond for Pway work
ATTACHMENT
.TenderCondition-GCC25.05.2026.pdf
ATTACHMENT
.SpecialConditionsforP-WayRelatedWorks05.09.2025.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at [email protected].