ADDN/ALTN TO EXISTING ELECTRIC SUPPLY LINES TO UG CABLES IN NCO QTRS AT NDA KHADAKVASLA

Amount

Dismantling cross-arms of MS channel or angle section etc. complete

Dismantling and taking down of ACSR Conductors of any type/size from the existing LT Pole etc complete.

Dismantling insulators any type, any size from LT pole cross arms etc complete.

Dismantling of GI Earth/Guard wire of any size from the existing LT Pole etc complete.

Dismantling stay assembly complete of existing LT Pole including earthwork etc complete.

Dismantling old unserviceable steel struts, any size including earthwork etc complete.

Taking out old LT UG power cable of following sizes :- (Note:- Excavation and Earth work shall be measured and paid separately under respective items of BOQ).

(a) 300 Sqmm 3.5 Core.

(b) 240 Sqmm 3.5 Core

(c) 16 Sqmm 4 Core.

Relaying of old serviceable LT UG power cable retrieved from item No. 7.0 above of following sizes :- (Note:- Excavation & Earth Work shall be measured and paid separately under respective item of BOQ).

(a) 300 Sqmm 3.5 Core.

(b) 240 Sqmm 3.5 Core

(c) 16 Sqmm 4 Core.

Dismantling old unserviceable GI Protection Pipe of 50mm bore.

Supply, lay, test, connecting and commissioning under ground cable, LT 1100 volts grade, heavy duty XLPE insulated, armoured with aluminium stranded conductor complete laid in trenches/fixed to poles/drawn through pipes with suitable size cable glands, crimping type cable lugs etc all as specified and directed of following sizes:-

(a) 3.5 Core 300 Sqmm

(b) 3.5 Core 240 Sqmm

(c) 3.5 Core 185 Sqmm

(d) 3.5 Core 150 Sqmm

(e) 3.5 Core 120 Sqmm

(f) 3.5 Core 95 Sqmm

(g) 3.5 Core 70 Sqmm

(h) 3.5 Core 50 Sqmm

(j) 3.5 Core 35 Sqmm

(k) 3.5 Core 25 Sqmm

(l) 4 Core 16 Sqmm

Excavation in trenches n.exc 1.5mtr wide and n.exc. 1.5m in depth for foundation of poles, stay, laying of cable & pipe etc and getting out in hard/dense soil .

Excavation in trenches n.exc 1.5mtr wide and n.exc. 1.5m in depth for foundation of poles, stay, laying of cable & pipe etc and getting out in soft rock.

Excavation in trenches n.exc 1.5mtr wide and n.exc. 1.5m in depth for foundation of poles, stay, laying of cable & pipe etc and getting out in hard rock.

Returning filling in soil including spreading, levelling, watering and well ramming in layers n.exc. 25cm

Removing excavated material not exceeding 50mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point all as specified and directed.

M&L providing fine dry river sand as in sand cushioning for LT under-ground cable protection in trenches, including spreading, levelling, punning down sand in layers and consolidating complete all as specified and as directed. Note:- Only punned thickness of sand shall be considered for measurement purposes.

Supply and laying burnt clay fly ash building bricks, designation 75 (Kg/Sqcm) laid in right angle along the cable, complete all as specified and directed.

M & L for laying of half round unreinforced concrete pipe, of inner dia 150 mm and outer dia 200 mm, half round for bottom and half round for top and before laying excavated area shall be leveled, complete all as specified and directed. (Note : 01 Half round top and 01 half round bottom together will be considered as one running meter). Make : as per sample approved by Engr-in-Charge.

Demolition of cement concrete of any description and in any position complete

M&L for Earthing complete with GI earth plate electrode of size 60cmx60cmx6mm thick burried directly in ground to a depth not less than 2.25 m and top edge of the plate not less than 1.5 mtr below normal ground level including connecting GI earth strip 25x4 mm by GI nuts bolts, washers all as shown in electrical plate No.3 of SSR Part I of 2009 including funnel, RCC 1:2:4 type B0 using 12.5mm graded stone aggregates and 6mm dia mild steel bars at 100mm c/c as in chamber cover,, charcoal salt etc complete including excavation and earth work in any strata and testing on completion including filling up the earth pit with black cotton soil for best result and removal of excavated material from the site complete. (Note : Rate is inclusive of GI strip upto 7.5mtr length and beyond 7.5 mtr shall be measured and paid separately).

Surface dressing n.exc 15cm deep including cleaning grass vegetation saplings shrubs, bush wood, ungrowth roots and trees not exc 30cm girth including disposal of spoils, in any type of soil all as directed.

M & L for spreading & levelling 20 mm graded coarse stone aggregates in a layer of required thickness with in the existing Sub Stn Yard etc all as specified and directed.

Preparing old painted steel surfaces over 10cm width or girth and applying one coat of synthetic enamelled paint

Disconnecting existing connections for carefully shifting including loading, unloading and transporting of 400 KVA, 11000/433 Volts, 50 Hz, AC Outdoor type distribution transformer from NCOs Sub Stn Yard to Power House and 500 KVA 11000/433 Volts, 50 Hz, AC Outdoor type distribution transformer from Power House Yard to NCOs Sub Stn Yard (distance not more than 2.0 km one way) and Installed the same transformer at transformer plinth including termination of its both HT /LT side with new HT/LT Power Cables, Earthing strips etc by taking proper safety precautions for working personnel complete all as directed by Engr-in-Charge. ( Note : If any damage occured to the transformer during this course of action, the damaged parts of the Transformer shall be replaced by the contractor without any extra cost to the Deptt).

M & L and fixing danger notice plate of 1.6mm thick mild steel sheet, vitreous enamelled white, with letters, figures and conventional skull and bones in signal red colour and fixed with M.S. clamps, bolts and nuts of approved size 200 x 150 mm for LT Supply including taking down existing one complete all as specified and directed.

Taking out old LT panel and Design, supply, install, test and commissioning of main LT Panel, weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 1200 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints an+B56d connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be showing the arrangements of circuit shall be pasted inside the panel door and covered with transparent laminated plastic sheet . The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 6 Nos 70x70x5mm thick angle iron supports of not less than each 1.5 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 2500mmX850mmX1500mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) Supply and fixing including testing of ACB 4 Pole, 415 Volts, 800 Amp, 50 KA, Manual Draw Out (MDO) type with microprocessor based LSIG & temprature rise protection consisting of digital LCD display with battery backup, Current Metering and RS 485 port complete all as specified and directed.- 01 No (Incomer) Make : Legrand-DMX3 / ABB-Tmax / Siemens-3 WL.

Outgoing

(a) MCCB 4 Pole, 415 Volts, 320 Amp with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu, suitable for Isolation, Adjustable overload setting : 0.4 - 1.0 x In, Adjustable short circuit setting 1.5 - 10 x Ir, Manual type, inbuilt display for current metering with accuracy Class 1, Internal battery measure function, comm port, inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. - 04 Nos.

(b) MCCB 4 Pole, 415 Volts, 250 Amp, with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu, suitable for Isolation, Adjustable overload setting : 0.4 - 1.0 x In, Adjustable short circuit setting 1.5 - 10 x Ir, Manual type, inbuilt display for current metering with accuracy Class 1, Internal battery measure function, comm port, inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. - 02 Nos.

(c) MCCB 4 Pole, 415 Volts, 125 Amp with thermal magnetic release, 25 KA, conforms to IS/IEC 60947-2, Ics = 100% Icu, suitable for Isolation, Adjustable Overlaod Setting : 0.8 - 1.0 x In with both side of spreader links and phase separater etc. - 01 No.

Taking out old LT panel and Design, supply, install, test and commissioning of main LT Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 1000 Amp. The busbars and Interconnecting links shall be insulated B61 heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be showing the arrangements of circuit shall be pasted inside the panel door and covered with transparent laminated plastic sheet . The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 6 Nos 70x70x5mm thick angle iron supports of not less than each 1.5 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 2000mmX850mmX1500mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cable and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) Supply and fixing including testing of ACB 4 Pole, 415 Volts, 630 Amp, 50 KA, Manual Draw Out (MDO) type with microprocessor based LSIG & temprature rise protection consisting of digital LCD display with battery backup, Current Metering and RS 485 port complete all as specified and directed. - 01 No (Incomer).

Outgoing

(a) MCCB 4 Pole, 415 Volts, 400 Amp with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu, suitable for Isolation, Adjustable overload setting : 0.4 - 1.0 x In, Adjustable short circuit setting 1.5 - 10 x Ir, Manual type, inbuilt display for current metering with accuracy Class 1, Internal battery measure function, comm port, inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. - 02 Nos.

(b) MCCB 4 Pole, 415 Volts, 320 Amp with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu, suitable for Isolation, Adjustable overload setting : 0.4 - 1.0 x In, Adjustable short circuit setting 1.5 - 10 x Ir, Manual type, inbuilt display for current metering with accuracy Class 1, Internal battery measure function, comm port, inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. - 01 No.

(c) MCCB 4 Pole, 415 Volts, 200 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In, Magnetic Adjustable 5 - 10 x In with both side of spreader links and phase separater etc. - 01 No.

Design, supply, install, test and commissioning of feeder Pillar Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 520 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1500mmX400mmX1200mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cable and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 320 Amp with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu, suitable for Isolation, Adjustable overload setting : 0.4 - 1.0 x In, Adjustable short circuit setting 1.5 - 10 x Ir, Manual type, inbuilt display for current metering with accuracy Class 1, Internal battery measure function, comm port, inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. – 01 No (Incomer).

(b) MCCB 4 Pole, 415 Volts, 100 Amp with thermal magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu, suitable for Isolation, Adjustable Overload Setting : 0.8 - 1.0 x In with both side of spreader links and phase separater etc.– 04 Nos (Outgoing)

Design, supply, install, test and commissioning of Feeder Pillar Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 400 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 4 Nos 50x50x6 mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1500mmX400mmX1200mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cable and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 250 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In, Magnetic Adjustable 5 - 10 x In with both side of spreader links and phase separater etc. – 01 No (Incomer).

(b) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc. – 03 Nos (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc. - 01 No (Outgoing).

Design, supply, install, test and commissioning of Feeder Pillar Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 520 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel+B75 shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1500mmX400mmX1200mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming/outgoing XLPE Cable and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 320 Amp with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.4-1.0 x In, Adjustable short circuit setting 1.5-10 x In Manual type, inbuilt display for current metering with accuracy of class 1, Internal battery measure function, COMM Port, Inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. – 01 No (Incomer).

(b) MCCB 4 Pole, 415 Volts, 200 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In, Magnetic adjustable 5 - 10 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc - 02 Nos (Outgoing).

(d) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 01 No (Outgoing).

Design, supply, install, test and commissioning of Feeder Pillar Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 520 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCB complete all as specified and as directed. The overall size of the panel shall not less than 1500mmX400mmX1200mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming/outgoing XLPE Cable and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 320 Amp with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.4-1.0 x In, Adjustable short circuit setting 1.5-10 x In Manual type, inbuilt display for current metering with accuracy of class 1, Internal battery measure function, COMM Port, Inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. – 01 No (Incomer).

(b) MCCB 4 Pole, 415 Volts, 125 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc - 03 Nos (Outgoing).

Design, supply, install, test and commissioning of Feeder Pillar Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 520 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1500mmX400mmX1200mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming/outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 320 Amp with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.4-1.0 x In, Adjustable short circuit setting 1.5-10 x In Manual type, inbuilt display for current metering with accuracy of class 1, Internal battery measure function, COMM Port, Inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. – 01 No (Incomer).

(b) MCCB 4 Pole, 415 Volts, 200 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In, Magnetic Adjustable : 5 - 10 xIn with both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 125 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(d) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(e) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 01 No (Outgoing).

Design, supply, install, test and commissioning of Feeder Pillar Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 400 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1000mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 250 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In, Magnetic adjustable : 5 - 10 x In with both side of spreader links and phase separater etc – 01 No (Incomer).

(b) MCCB 4 Pole, 415 Volts, 200 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In, Magnetic adjustable : 5 - 10 x In with both side of spreader links and phase separater etc – 01 Nos (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc - 01 No (Outgoing).

Design, supply, install, test and commissioning of Feeder Pillar Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 650 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1800mmX400mmX1200mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 400 Amp with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.4-1.0 x In, Adjustable short circuit setting 1.5-10 x In Manual type, inbuilt display for current metering with accuracy of class 1, Internal battery measure function, COMM Port, Inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. – 01 No (Incomer).

(b) MCCB 4 Pole, 415 Volts, 160 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc - 03 Nos (Outgoing).

(d) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 01 No (Outgoing).

Design, supply, install, test and commissioning of Feeder Pillar Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 520 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1500mmX400mmX1200mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 320 Amp with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.4-1.0 x In, Adjustable short circuit setting 1.5-10 x In Manual type, inbuilt display for current metering with accuracy of class 1, Internal battery measure function, COMM Port, Inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. – 01 No (Incomer).

(b) MCCB 4 Pole, 415 Volts, 160 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc - 02 Nos (Outgoing).

(d) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 01 No (Outgoing).

Design, supply, install, test and commissioning of Feeder Pillar Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 650 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with digital multifunction meter with accuracy Class 1 with RS 485 Parameters with cast Resign CTs etc and RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Feeder Panel & all incoming and outgoing MCCBs etc. The panel shall be provided 4 Nos 50x50x6mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1800mmX400mmX1200mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 400 Amp with Electronic Protection Unit, 36 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.4-1.0 x In, Adjustable short circuit setting 1.5-10 x In Manual type, inbuilt display for current metering with accuracy of class 1, Internal battery measure function, COMM Port, Inbuilt USB Port for software diagnosis with both side of spreader links and phase separater etc. – 01 No (Incomer).

(b) MCCB 4 Pole, 415 Volts, 160 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 03 Nos (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 125 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc - 01 Nos (Outgoing).

(d) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 01 No (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 320 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1200mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 200 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In, Magnetic adjustable : 5 - 10 x In with both side of spreader links and phase separater etc – 01 Nos (Incoming).

(b) MCCB 4 Pole, 415 Volts, 160 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 40 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 02 Nos (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 320 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1200mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 200 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In, Magnetic Adjustable : 5 - 10 x In with both side of spreader links and phase separater etc – 01 No (Incoming).

(b) MCCB 4 Pole, 415 Volts, 125 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 40 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 02 Nos (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 200 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1200mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 125 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Incoming).

(b) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 40 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 02 Nos (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 260 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1200mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 160 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Incoming).

(b) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 40 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 02 Nos (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 160 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1200mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Incoming).

(b) MCCB 4 Pole, 415 Volts, 40 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 03 Nos (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 260 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1200mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 160 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Incoming).

(b) MCCB 4 Pole, 415 Volts, 125 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 40 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc - 02 Nos (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 160 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1200mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Incoming).

(b) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 01 No (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 40 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc - 02 Nos (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 100 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1200mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 01 No (Incoming).

(b) MCCB 4 Pole, 415 Volts, 40 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 03 Nos (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 200 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1500mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 125 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Incoming).

(b) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 02 Nos (Outgoing).

(c) MCCB 4 Pole, 415 Volts, 40 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 02 Nos (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 160 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1000mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 100 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation, Adjustable Overload setting : 0.8-1.0 x In with both side of spreader links and phase separater etc – 01 No (Incoming).

(b) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 02 Nos (Outgoing).

Design, supply, install, test and commissioning of Sub Feeder Panel weather proof outdoor type double door, fabricated out of 3.15mm thick CRCA sheet with epoxy powder coating of RAL-7032 (Siemens Gray) shade with matt finish with seven tank pre treatment process. The panel shall be fabricated by CPRI approved manufacturer only as mentioned in Appendix 'C'. The panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-55, double door type with locking arrangement for front and back side, comprising of gaskets between all adjacent units and beneath all covers shall be fully gasketed with neoprene rubber and ventilation arrangement for heat dissipation from both side of panel. The panel shall be provided with Aluminium bus bars of high conductivity aluminium alloy, suitable for 3 phase 4 wire system (R,Y,B,N) rating not less than 100 Amp. The busbars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & Black colour coding. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in dedicated compartment. The panel shall be prewired with FRLS PVC insulated copper conductor cables of suitable size properly tagged and secured. All joints and connection shall be done with galvanized or cadmium plated high tensile nuts, bolts and washers. The panel shall be provided with RYB, ON, OFF & Trip LED indicating lamps at incoming. The panel shall be provided with manufacturer's name plate, skull & bones danger notice board, Name plate for Sub Feeder Panel & all incoming and outgoing MCCBs. The panel shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement . All MCCBs shall be provided with spreader links with phase separators on both side and suitable extended rotary handles for all Incoming & Outgoing MCCBs complete all as specified and as directed. The overall size of the panel shall not less than 1000mmX400mmX1000mm (LxDxH). The panel shall be provided with 2 Nos of Earting Terminals one on each side of the Panel with earth strip, suitable size of SS Cable glands for all incoming & outgoing XLPE Cables and including following accessories:- Note : 1. Drawing and design of panel must be approved by Engr-in-charge before manufacturing. 2. Two Stage inspection of manufacturing i.e. Fabrication before powder coating & during switchgear installation, inspection visit of Engr-in-Charge compulsory to be arranged by the contractor.

(a) MCCB 4 Pole, 415 Volts, 63 Amp with Thermal Magnetic release, 25 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 01 No (Incoming).

(b) MCCB 4 Pole, 415 Volts, 40 Amp with Thermal Magnetic release, 16 KA, Conforms to IS/IEC 60947-2, Ics = 100% Icu suitable for Isolation with Adjustable Overload setting : 0.8-1.0 & both side of spreader links and phase separater etc – 02 Nos (Outgoing).

Supply, fixing and commissioning automatic timer switch distribution board, factory assembled in powder coated sheet steel enclosure, comprising of 40 Amps 3 Pole power contactor and 230V digital time switch and 4 Pole 40 Amps, 10 KA MCB for controlling LED/SV etc street lights, including earth work for fixing Timer switch distribution Board and shall be provided 4 Nos 35x35x4mm thick angle iron supports of not less than each 1.2 mtr height duly painted with anti corrosive black paint and grouted in PCC 1:3:6 at suitable depth as per site requirement.

Supply & Fix on pole, SMC Junction box inner dimensions (270 x 225 x 135)mm (LxBxD), 3 phase 4 wire system, including cable connecting base, 6 Amp DP MCB with mounting SS railing, Cable lugs suitable to 10/16 Sqmm 4 core cable, connection for incoming and outgoing cables including Fixing arrangement on pole etc complete all as specified and directed by Engr-in-Charge.

S & F of Cable Route Marker made up of Cast Iron pipe of dia 100 mm and thickness 4.65 mm with supporting angle iron of size 20 x 20 x 3 mm and height 0.6 mtr for stand including priming, painting and wirting of "LT CABLE" in suitable size of letter including necessary earthwork and grouted at suitable depth in PCC 1:3:6 Type C2 using 40 mm graded aggregate in mass concrete complete all as specified and directed at site by Engr-in-Charge.

M & L for PCC 1:3:6 type C2 (40 mm graded aggregate ) for base and foundation, filling & mass concrete for Pole coping etc complete all as specified and directed.

S & F of 2.5 Sqmm 3 core Weather proof AL multistranded cable PVC insulated not less then 7 mtr on existing street lights and properly drawn through existing street light bracket, Pole and hole of street light pole including making of two 20mm hole on existing street light pole and taking down existing 2.5 Sqmm aluminium twin core cable complete all as specified and directed at site. Note : The contractor shall be responsible for any damage due to the existing street light and the damaged parts of street light shall be replaced by the contractor without any extra cost to the Deptt.

M & L for road cutting of size (45x45) cm as required for laying pipe/cable etc and making good to match with existing one including earthwork and necessary excavation, complete all as specified and as directed.

M&L for PCC / Interlocking tiles path way cutting of size (45x45) cm as required for laying pipe/cable etc and making good to match the existing one complete all as specified and as directed.

M & L for Straight Through Jointing Kit Heat Shrink type suitable for 1.1 KV LT XLPE armoured aluminium stranded conductor Cable Outdoor type complete with jointing material and accessories complete all as specified and directed of following sizes :-

(a) 3.5 Core 300 Sqmm.

(b) 3.5 Core 240 Sqmm

(c) 3.5 Core 185 Sqmm

(d) 3.5 Core 150 Sqmm

(e) 3.5 Core 120 Sqmm

(f) 3.5 Core 95 Sqmm

(g)t 3.5 Core 70 Sqmm

(h)3.5 Core 50 Sqmm

(j) 3.5 Core 35 Sqmm

(k) 3.5 Core 25 Sqmm

(l) 4 Core 16 Sqmm

S & F of LT Busbar panel weather proof outdoor type double door, fabricated out of 3.15 mm thick CRCA sheet with epoxy powder coating of RAL-7035 ( Siemens Gray) shade with matt finish with seven tank pre treatment process. The Panel shall be compartmentized design totally enclosed, dust and vermin proof, conforming to degree of protection IP-43, Gaskets between all adjacent units and beneath all covers shall be provided to render the joints dust proof. All doors and covers shall be provided with cylindrical panel locks and shall be fully gasketed with neoprene rubber and shall be lockable. The panel shall be provided with aluminium bus bars electrolytic grade of 300 amps current rating. The bus bars and Interconnecting links shall be insulated with heat shrinkable PVC sleeve with RYB & black colour coding and fix horizontally. The bus bars shall be supported on unbreakable, non-hygroscopic SMC insulated supports at sufficiently close intervals to prevent busbars sag and shall be housed in a dedicated compartment. All joints and connection shall be done with galvanised or cadmium plated high tensile nuts, bolts, washers and AL Lugs etc. The panel shall be provided with 04 Nos 35mmx35mmx4mm thick angle iron supports of not less than each 1.0 mtr height duly painted with anti corrosive black paint including earth work and grouted in PCC 1:3:6 at suitable depth as per site requirement including taking down existing one. The overall size of the Busbar panel shall not be less than 500mmx300mmx550mm (LxDxH) including 4 Nos cable entry holes suitable for cable entry up 3.5C 185 Sqmm at bottom complete all as specified and directed.

M & L for tubes, light Grade, galvanised with all fittings, laid in trenches or with pole/wall for protection of Cable etc with fixing accessories such as Shaddle, nut-bolts etc of following sizes complete all as specified and directed of following sizes :-

(a) 50mm bore

(b) 80mm bore

(c) 100mm bore

(d) 150mm bore

Shri Sai Electricals

S G Enterprises

M/S DEV ENTERPRISES

SHAILENDRA B TULSANI

SBS Enterprises

Prasur Electricals & Engineering Co.