REPAIR / MAINT OF JOINERY, PLASTERING, ROOFING, PLUMBING AND SANITARY FITTINGS AT OVL AND GFA SF ACCN IN THE AREA OF AGE B/R-II UNDER GE (WEST) LUCKNOW

Amount

Demolition of Concrete concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed

Demolition of old brick work or stone/boulder masonary built in cement mortar including all quoins, pillars etc but excluding ashlar facings, dressed stone work and precast articles complete all as specified and directed.

M&L for brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L for with fly ash bricks, old size, straight or curved on plan to any radius in half brick walls built in cement mortar 1:4 complete all as specified and directed.

M & L 15 mm thick rendering in CM (1:6 ) on fair faces of brick wall or concrete surfaces finished even and smooth without using extra cement including taking down cement plaster or cement lime plastering , any descriptuon from brick wall including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M & L 15 mm thick rendering in CM (1:4 ) on fair faces of brick wall or concrete surfaces finished even and smooth without using extra cement including taking down cement plaster or cement lime plastering , any descriptuon from brick wall including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M & L 5 mm thick rendering in CM (1:3 ) on concrete surfaces of ceiling finished even and smooth without using extra cement including taking down cement plaster or cement lime plastering , any descriptuon from brick wall including racking out joints hacking for key scrubbing down with water etc complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying two coat of oil bound distemper over a coat of primer complete all as specified and directed.

M & L for preparation of new plastered surface of walls by washing rubbing and applying two coats of cement based paint over a coat of white cement primer complete all as specified.and directed. .

M & L for preparation of new plastered ceiling surface and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old surface of wall and applying one coat of oil bound distemper complete all as specified and directed.

M&L for preparation of old surface of walls and applying one coat of cement base paint complete all as specified and directed.

M & L for preparation of old plastered ceiling surface and applying one coat of white wash complete all as specified and directed.

M & L for preparation of old plastered wall surface and applying one coat of white wash complete all as specified and directed.

M&L for preparation of old painted surfaces of wood and wood based material of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.

M&L for preparation of old painted steel and iron surfaces of any description over 10 cm in width or girth and applying one coat of synthetic enamel paint of approved tint all as specified & as directed.

M&L Vitrified Ceramic coloured tiles light shade 10 mm thick (square/ rectangular) polished, joint free , area of each tiles not exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15mm thick screed bed in cement & sand mortar 1:4, complete including dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises all as specified and as directed.

M&L for non skid ceramic tiles (coloured) 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm as in floors, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 15mm thick screed bed in cement & sand mortar 1:4, complete including dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises all as specified and as directed.

M&L for glazed ceramic tiles (coloured) 350x250x7mm/450 x 350 x 7mm thick on vertical surfaces such as dado, skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles over & including 10 mm thick rendering (as screed bed) in cement & sand mortar 1:4, incl dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed.

M&L for 40mm thick PCC 1:2:4, type B-1 using 20mm graded crushed stone aggregae as in floors, finished even and smooth using extra cement complete all as specified and directed.

Taking up or down steel water tubing and connections of 15mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

Taking up or down steel water tubing and connections of 20mm bore, fixed in walls, ceiling, floors, trenches etc. complete all as specified and directed.

M&L for cutting chases, pinning in, making good to facings as original where required and pointing in cement mortar 1:3 for concealed water tubing etc. and making good, cutting not exc 10 cm girth in brick walls complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 15mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

M&L for galvanized steel water tubing medium grade of 20mm bore with & including all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S&F in repairs vitreous china squatting pan (Orissa pattern) water closet (white) of size 580x440mm with integral foot rests, 'P' or 'S' trap, including connection to trap and flushing pipe, anti-syphonage pipe etc including provision of PCC (1:5:10) type E2 in filling, making good to floor complete all as specified and directed.

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white including fixing bolts, seat cover and flush pipe complete all as specified and directed

S&F in repairs PVC valveless symphonic action type low level flushing cistern (ISI marked) of 10 litre capacity including 32 mm dia PVC flush pipe connected to water closet with inlet, ball valve, float and handle complete all as specified.

S&F in repairs vitreous china wash hand basin, white, flat back of size 550mm x 400mm with & including a pair of cast iron brackets embedded in PCC 1:3:6 type C1 blocks of size 10x7.5x15cm, 32 mm dia PVC waste pipe and 32mm bore chromium plated brass waste fitting with long screwed shanks and fly nuts, flange end bedded in red lead cement & other end fixed, (excluding tap, waste chain & plug), complete all as specified.

S&F in repairs long body 15mm bore bib tap, cast copper alloy, chromium plated with capstan head, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed.

S&F CP angle valve for 15 mm bore pipe with capstan head long screwed shank including CP flange fancy type fixed as in repair complete all as specified and directed.

S&F in repair 15mm bore concealed type, stop valve cast copper alloy screwed down high pressure with capstan head and cup, screwed both ends for iron pipe or for unioncomplete all as specified and directed.

S&F in repair fancy type pillar taps cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered Hot or Cold with long screwed shanks and flynuts, screwed for iron pipes and fixed for 15mm dia complete all as specified and directed.

S&F in repair hand shower (Health faucet) with 1 Mtr flexible tube with wall hook bracket etc, complete set of superior quality complete all as specified and directed.

S&F in repairs brass chromium plated shower rose 125 mm size without swivel joint including fixing to steel pipe of 15mm bore or union complete all as specified and directed.

Dismantling PVC water tanks and removing for capacity exceedin 250 litres & not exceeding 500 litres etc.complete all as specified and directed.

S&F 500 Litre capacity Rotational moulded polyethylene water storage tanks triple layered (cylindrical, vertical with closed top) ISI marked, hoisted & fixed in position & making necessary arrangements for fixing inlet, outlet & over flow pipe & provision of wash out pipe etc. complete all as specified and directed.

S&F 20 mm ball valve high pressure of PTMT with apoxy coated aluminium rod and high density plastic ball screwed for iron pipe, complete all as specified and directed.

Demolition and breaking up or taking down PVC/AC/CI pipes of any dia/bore complete all as specified and directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including PVC holding clamps, complete all as specified and directed.

Taking down chowkhat with shutter (without taking off shutter from the frame) and area not exc 1.5 sqm each, complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening including easing and adjusting of shutter as required including renewal of unserviceable screws complete all as specified and directed.

Taking down shutter of any description exc 1 Sqm and not exc 2 Sqm each and and removal from site all as specified and directed.

M&L 35mm thick factory made shutter plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed.

Supply and fixing factory made 35mm thick glazed and skeleton shutters made of second class hard wood, open rebated and prepared to receive glass, gauze etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in clause 8.24 (a) of Section 8 in SSR Part-I, kiln seasoned and chemically pressure treated, fixed to chowkat, complete all as specified & directed.

Supply and Fixing Pressed steel frames size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

S & F factory made solid PVC door frame of size 50 x 47 mm made our of 5mm plain colour PVC sheet reinforced with 19 mm MS square tube with wall thickness 19 gauge complete all shown and specified at srl page No 150 of SSR Pt – II (Rates) & directed. Note :- (i) EDPM rubber gasket weather seal to be provided through out the frame ( ii) The frame shall be miter cut at two corners and jointed by inserting 02 Nos of 150 mm brackets of 15 x 15 mm MS square tube inside the 19mm X 19mm tube and suitably screwed (iii) 4 Nos 75 mm long MS screw fixed with PVC fasteners shall be provided in each frame

S&F 30mm thick PVC factory made panneled door shutter with wood grain printed & decorative beading with 10mmx10mm as per IS- 4020 made from MS tube of top and bottom rods. MS frame shall be covered with heat maulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on plain side & as gap insert for top and bottom rail. Pannelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beeding and jointed together with solvent cement as per specification and drawings complete all as specified and directed. .

S&F 300 mm long aluminium anodised sliding door bolts, with bright bolt not less than 12mm dia and including a minimum of 06 bolts and nuts, four on bolt plate and two on staple plate and fixed, complete all as specified.

S&F mild steel helical door spring 300mm ordinary rat tail rod pattern spring including roller and roller plate complete all as specified and directed.

S&F butt hinges of size 100 mm medium weight, stainless steel ISI marked complete all as specified and directed.

S&F aluminium handle, 150mm size, cast type, anodized (ISI marked) complete all as specified and directed.

S&F in repair stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire, staples complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc) sheets in roof coverings complete all as specified and directed.

S&F multi-rib TM profile, tensile strength 550 Mpa, colour coated 0.50mm thick pre-painted galvalume aluminium zinc coated GI based corrugated steel sheet, having maximum pitch of 250mm c/c and minimum 30mm crest depth in length as per site requirement, the feed material manufactured out of 0.50mm (TCT) with coating of 18-20 microns top coat over 5 microns primer and 8-10mm alkaline back of zinc aluminium alloy of AZ-150, including the sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium 55% and silicon 1.5% with total mass coating of 150 gms/sqm on both sides having covered width 1020mm and return leg for proper side lap as in roof covering/ cladding and fixed with self tapping screws with EDPM seal complete all as specified and directed.

S&F multi-rib TM profile, tensile strength 550 Mpa, colour coated 0.50mm thick pre-painted galvalume aluminium zinc coated GI based plain steel sheet, having maximum pitch of 250mm c/c and minimum 30mm crest depth in length as per site requirement, the feed material manufactured out of 0.50mm (TCT) with coating of 18-20 microns top coat over 5 microns primer and 8-10mm alkaline back of zinc aluminium alloy of AZ-150, including the sheet shall have a hot dip metallic zinc aluminium alloy coating of zinc 43.5%, aluminium 55% and silicon 1.5% with total mass coating of 150 gms/sqm on both sides having covered width 1020mm and return leg for proper side lap as in roof covering/ cladding and fixed with self tapping screws with EDPM seal complete all as specified and directed.

S&F in repair for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated), Fe - 410- W(Gde - E 250 quality B) complete all as specified and directed

Supply and fixing framed work such as grills, gratings etc with ends of bars shouldered and / or riveted or forget into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, frame work of water tank and similar work conforming to Fe 290 Gde E-165 complete all as specified and directed.

M&L preparation of new steel surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

S&Fin repair stainless steel 25mm dia curtain rods including brackets and fancy type end knobs, complete, all as specified and directed.

S&F in repairs 'E' board everest 600 x 600 x 4mm thick white, prelaminated sett embossed reinforced designer ceiling board tiles of approved texture at all height laid on hot dipped GI imposed grid with 24mm wide T sec exposed flanges which shall be pestered coated white. The frame work shall comprise of main runner made from 0.33 mm thick GI sheet of size 24x32x300mm and spaced at 1200 mm C/C securely fixed to structural soffits by approved hangers at 1200mm C/C. Hanger of GI wire 4 mm dia to be fixed by approved recoil plug, screw etc. The last hanger at the end of each main runner shall not be greater than 450 mm from adjacent wall. flash fitting of 1200 mm long cross tee (with double sticking) to be interlocked between main runner at 600 mm centre from 1200x600 mm to modules cross tee longer than 600 mm to be supported independency 600x600 mm double to be formed by filling 600 mm long cross tee centrally between the 1200 mm cross tee. The perimeter wall angle shall be of 0.45 mm thick GS sheet of size 19x19 mm and 300 mm long of white colour all as per manufacture's instructions complete all as specified and including demolition of old ceiling board complete as directed.

S&F powder coated (Powder coating not less than 50 micron thick) Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle(1 no.) complete all as specified and directed.

awashyakta enterprises

suniltraders

M/s Sachkhand Traders

R K CONTRACTOR AND SUPPLIERS

M/s Sultan Khan

M/s Vimal Traders