REPAIRS TO ROOF, FLOORING, PLINTH PROTECTION, JOINERY, PLASTERING, CHAJJA, PLUMBING, WORKS TO DOORS, WINDOWS ETC. TO MD AND OTM ACCOMMODATION OF ZONE A UNDER AGE(I) NAVY CHENNAI

Amount

Demolition of brick work or stone boulder masonary, built in cement mortar including all quions, arches pillars etc. but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed by Engineer in Charge.

M&L for Brickwork with fly ash bricks, straight or curved on plan exceeding 6m mean radius built in cement mortar (1:6) complete all as specified and directed by Engineer in Charge.

Demolition of cement concrete in ground floors and pavings not exceeding 15cm thickness (below and above gorund level) complete all as specified and directed by Engineer in Charge.

Demolition of reinforced cement concrete in ground floors and pavings not exceeding 15cm thickness (below and above gorund level) complete all as specified and directed by Engineer in Charge.

M&L for plain cement concrete 75mm thick, type C1, 1:3:6, using 20mm graded stone aggregate, as in plinth protection complete all as specified and directed by Engineer in Charge.

M&L for pre cast cement concrete in landings covers slabs (for man holes etc) chullah hoods, chajjas, water rough, managers, shelves & similar articles with plain faces complete all as specified and directed by Engineer in Charge. Note : Reinf shall be measured and paid separately

M&L for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed by Engineer in Charge.

Ditto as in item No. 7 but for 6 to 8 mm dia complete all as specified and directed by Engineer in Charge.

Taking down shutters not exceeding 1.50 Sqm each as in aluminium doors/windows and refixing in same openng with resecuring, adjusting, easing alighning strighthning and making openable the shutter including replacing rubber neoprane packing, screws , replacement of lugs glazing clips, hinges etc complete all as in aluminium doors complete all as specified and directed by Engineer in Charge.

Taking down shutters exceeding 1.5 Sqm and not exceeding 4.00 Sqm each as in aluminium doors/windows and refixing in same openng with resecuring, adjusting, easing alighning strighthning and making openable the shutter including replacing rubber neoprane packing, screws , replacement of lugs glazing clips, hinges etc complete all as in aluminium doors complete all as specified and directed by Engineer in Charge.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exc 1.5 sqm complete all as specified and directed by Engineer in Charge.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames)exceeding 1.5 sqm but not exceeding 4.00 Sqm each complete all as specified and directed by Engineer in Charge.

Taking down wooden shutter of any description not exceeding 1.0Sqm each and refixing the same opening resecuring and adjusting etc complete all as specified and directed by Engineer in Charge.

Taking down wooden shutters of any description not exceeding 1.0 sqm but not exceeding 2.0 sqm each and refixing the same opening resecuring and adjusting etc complete all as specified and directed by Engineer in Charge.

Taking down wooden shutters of any description but exceeding 2.0 sqm and refixing in the same opening complete all as specified and directed by Engineer in Charge.

S&F 4mm thick plain glass panes including hacking out old brocken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing clips, channel complete all as specified and directed by Engineer in Charge.

S&F 5.50 mm thick plain glass panes including hacking out old brocken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing clips, channel complete all as specified and directed by Engineer in Charge.

S&F figured glass pin headed type 4mm thick including hacking out old brocken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing clips, channel complete all as specified and directed by Engineer in Charge.

S&F sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x420mm bowl size 410mm x 330mm x 160mm complete all as specified and directed by Engineer in Charge.

S&F PVC water tanks rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl 20 mm brass float valve all as specified in SSR Part-I of capacity 500 litres complete as in fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F PVC water tanks rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position incl 20 mm brass float valve all as specified in SSR Part-I of capacity 1000 litres complete as in fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F PVC water tank Cover with fittings suitable upto 1000 litres capacity as in repairs complete all as specified and directed by Engineer in Charge.

S&F ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) and fixed as in repairs of bore of pipe 20mm complete all as specified and directed by Engineer in Charge.

S&F ball valves, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed (minimum weight 210 gms) and fixed as in repairs of bore of pipe 25mm complete all as specified and directed by Engineer in Charge.

Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes etc of tank capacity exceeding 500 litres and not exceeding 1000 litres, removal of existing date and writing new stenciled date of cleaning complete all as specified and directed by Engineer in Charge.

Taking up or down steel tubing 15mm dia and connections including removal from site and connection in new or old position( Walls, ceiling, floors etc.) complete all as specified and directed by Engineer in Charge.

All as per Sl item No. 27 above but 20mm dia

All as per Sl item No. 27 above but 25mm dia

S&F steel water tubing 15mm dia and connectios including all fitting and fixed complete to walls and ceiling or laid in floors as in fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F steel water tubing 20mm dia and connectios including all fitting and fixed complete to walls and ceiling or laid in floors as in fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F steel water tubing 25mm dia and connectios including all fitting and fixed complete to walls and ceiling or laid in floors as in fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F second class hard wood palin, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chemfered, put together with glue pinned at joints, etc, complete all as specified and directed by Engineer in Charge.

S&F 35mm thick Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed by Engineer in Charge.

All as per Sl item No 34 above but 30mm thick in windows without sash bar

S&F 35mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density of thickness 35mm in second class hard wood complete all as specified and directed by Engineer in Charge.

S&F 30mm thick flush shutters, soild core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and directed by Engineer in Charge.

Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed by Engineer in Charge.

Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel heaving a PVC sheet strip of 20mm width suck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and directed by Engineer in Charge.

S&F 100mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F 300mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F Butt hinges, medium weight, cold rolled mild steel, and fixed of size 75mm complete all fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F Butt hinges, medium weight, cold rolled mild steel, and fixed of size 100mm complete all fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F 100 mm aluiminum anodised but hinges, extruded brass, with mild steel hinge pin,anodised and fixedin repairs complete all as specified and directed by Engineer in Charge.

S&F 75 mm aluiminum anodised but hinges, extruded brass, with mild steel hinge pin,anodised and fixedin repairs complete all as specified and directed by Engineer in Charge.

S&F 100 mm Aluminium handles, cast type, anodised etc all as fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F 75 mm Aluminium handles, cast type, anodised etc all as fixed in repairs complete all as specified and directed by Engineer in Charge.

S&F Brass Mortice lock, vertical type, size 100mm size 100mm complete as in repairs complete all as specified and directed by Engineer in Charge.

S&F 150 long hooks and eyes, aluminium plate type II complete all as specified and directed by Engineer in Charge.

S&F 40mm dia, cupboard knobs fixed with nut, screws and washers of brass polished complete all as specified and directed by Engineer in Charge.

S&F hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screws of size 100mm complete as in repairs complete all as specified and directed by Engineer in Charge.

S&F hasp and staple, safety type, aluminium anodised with hinge pin including bolt to hinge plate and fixed with screws of size 75 mm complete as in repairs complete all as specified and directed by Engineer in Charge.

S&F in repair Door closer, hydraulically regulated, door closer, aluminium (die cast) body, designation No.3, universal type and fixed complete all as specified and directed by Engineer in Charge.

S&F in repair Aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mm and fixed with beading to wooden frames complete all as specified and directed by Engineer in Charge.

S&F 300 mm long aluminium anodised peg stays 300 mm size complete all as specified and directed by Engineer in Charge.

S&F 100mm Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in repair complete all as specified and directed by Engineer in Charge.

S&F MS angle in mild steel works as in hold fasts and similar small articles etc complete all as specified and directed by Engineer in Charge.

M&L plan cement concrete (1:2:4) type B-1 using 20mm graded aggregate as hold fast, kerb stone etc. complete all as specified and directed by Engineer in Charge.

S&F Anodized Aluminium Frame for doors, windows, ventilators,partitions with one or more rebates including joining cleat,clips for fixing etc. complete all as specified and directed by Engineer in Charge.

S&F Anodized Aluminium shutter for doors, aluminium section weighing 0.55kg/m including necessary joining cleats glazing clips rubber neoprene packing handle 2 nos in each door hinges anodized snap beading screws etc complete all as specified and directed by Engineer in Charge.

S&F Powder coated Aluminium Frame for doors, windows, ventilators,partitions with one or more rebates including joining cleat,clips for fixing etc. complete all as specified and directed by Engineer in Charge.

S&F Powder coated Aluminium shutter for doors, aluminium section weighing 0.55kg/m including necessary joining cleats glazing clips rubber neoprene packing handle 2 nos in each door hinges anodized snap beading screws etc complete all as specified and directed by Engineer in Charge.

S&F anodized Aluminium shutter for sliding window , aluminium section weighing 0.55kg/m including necessary joining cleats glazing clips rubber neoprene packing including heavy duty rollers, locking arrngement etc anodized snap beading screws complete all as specified and directed by Engineer in Charge.

S&F Plywood, grade BWR, type BB, 12mm thick, fixed with nails to timber frame work as in pelmet box as in repairs complete all as specified and directed by Engineer in Charge.

S&F Prelaminated particle board, 25mm thick, interior grade, prelaminated both sides with decorative choice laminations fixed as in shutters / shelves of cupboard shutters, door shutter inserts and the like as in repairs complete all as specified and directed by Engineer in Charge.

Taking down cement plaster any description, on brick or stone walls or ceiling , etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed by Engineer in Charge.

M&L for Rendering 15mm thick in cement mortar 1:4 on concrete /Brick surfaces using with WPC complete all as specified and as directed. (Note : WPC shall be meaured and paid separately)

Supply only integral water proofing compound

M&L for rendering 10mm thick in cement mortar 1:6 on fair faces of concrete surfaces of wall finished fair and even complete all as specified and directed by Engineer in Charge.

Preparing plastered or unplastered new decorated surfaces of walls and applying two coats of cement based paints including finishing with putty in narrow widths, bands, cornices pilasters etc,. complete all as specified and directed by Engineer in Charge.

Preparing newly plastered surfaces of walls and applying three coats of white wash on plastered wall surfaces including in narrow widths, bands, cornices, pilasters etc.,

S&F 20 mm CP conduit for curtain rod including bracket fixed in pelmet boxes or independent without pelmet box as in repairs complete all as specified and directed by Engineer in Charge.

S&F Bib taps, fancy type, chromium plated, cast copper alloy, with long body with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule of bore of pipe 15mm fixed as in repairs complete all as specified and directed by Engineer in Charge.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe of bore of pipe 15mm fixed as in repairs complete all as specified and directed by Engineer in Charge.

S&F Stop valves, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore of pipe 15mm as in repairs complete all as specified and directed by Engineer in Charge.

S&F Stop valves for shower, fancy type, chromium plated with long shank and cup (concealed type) cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions of bore of pipe 15mm complete all as specified and directed by Engineer in Charge.

S&F 15 mm dia Gun metal, globe or gate valves, with iron wheel head screwed both ends for iron pipe as in repairs complete all as specified and directed by Engineer in Charge.

S&F 20 mm dia Gun metal, globe or gate valves, with iron wheel head screwed both ends for iron pipe as in repairs complete all as specified and directed by Engineer in Charge.

S&F 32mm Waste fittings, brass, chromium plated for glazed ware basins etc., with long screwed shanks and fly nuts,as in repairs complete all as specified and directed by Engineer in Charge.

S&F Grating doom 125mm dia of PTMT (minimum weight 40 gms) fixed over floor trap/nahanitrap complete all as specified and directed by Engineer in Charge.

S&F Towel Rail 600mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats (Minimum weight 190gms) complete all as specified and as directed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm as in repairs complete all as specified and as directed.

Vitreous china wash down water closet pan (pedestal pattern) white including all fiitings with "P" or "S" trap, as in repairs complete all as specified and directed by Engineer in Charge.

S&F Vitreous china squatting pan, "Orissa" pattern, size 580mm x 440mm white, with integral foot rests with "P" or "S" trap, fixed as in repairs complete all as specified and directed by Engineer in Charge.

S&F PVC valveless, syphonic action type flushing cistern 10 litres capacity low level, white with inlet, ball valve, float and handle, including brackets and connections complete all as specified and directed by Engineer in Charge.

S&F Brass Chromium plated shower roses 125mm size with swiel joints, including fixing to steel pipe or union as in repairs complete all as specified and directed by Engineer in Charge.

S&F PVC 32 mm dia fllush pipe for low level fulsh tank fixed including all joints as in repairs complete all as specified and directed by Engineer in Charge.

S&Fplastic water closet seat cover, black,white closed pattern with flat bottom and cover and mild steel chromium plated or aluminised hinging device as in repairs complete all as specified and directed by Engineer in Charge.

S&F Vitreous china wash basin, white, flat back, size 550mm x 400mm but including brackets and fixed in reapirs complete all as specified and directed by Engineer in Charge.

S&F Health faucet, brass, chromium plated with pipe length 1200mm, washers, connections etc., as in repairs complete all as specified and directed by Engineer in Charge.

S&F PVC waste hose pipe with 32mm dia as waste pipe to WHB/urinal/sink as in repairs complete all as specified and directed by Engineer in Charge.

S&F 40 mm dia chromimun plated waste coupling fixed in sink as in repairs complete all as specified and directed by Engineer in Charge.

Dismantling of PVC drain pipe up to 150 mm dia including all fittings such as bend, Tee and single 'Y' etc. complete all as specified and directed by Engineer in Charge.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer in Charge.

S& F PVC SWR pipes 75 mm single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed by Engineer in Charge.

S&F 110mm PVC (SWR) bends any redius complete all as specified and directed by Engineer in Charge.

S&F of 110 mm dia PVC (SWR) junction single door T equal or unequal complete all as specified and directed by Engineer in Charge.

S&F PVC SWR vent cowl 110mm complete all as specified and directed by Engineer in Charge.

S&F 75mm PVC (SWR) bends any radius complete all as specified and directed by Engineer in Charge.

S&F PVC SWR branch piece single (Single Y) equal or unequal 75mm dia complete all as specified and directed by Engineer in Charge.

S&F PVC SWR Junction single door T equal or unequal 75mm dia complete all as specified and directed by Engineer in Charge.

S&F PVC SWR vent cowl 75mm complete all as specified and directed by Engineer in Charge.

S&F PVC 75 mm size (SWR) floor trap plain with grating including jointing with solvent paint complete all as specified and directed by Engineer in Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and directed by Engineer in Charge.

M&L for Non skid cermic coloured floor tiles 7 mm to 8 mm thick (suare or rectangular area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match but with including screed bed in CM 1:4 15 mm thick complete all as specified and directed by Engineer in Charge.

M&L for glazed ceramic coloured tiles in vertical surfaces 350x250x7 mm/450x350x7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match including backing coat in Cm1:4, 15 mm thick complete all as specified and directed by Engineer in Charge.

S&F 15mm dia Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed in repairs complete all as specified and directed by Engineer in Charge.

Attending minor complaints of joinery such as wooden/steel/aluminium of any description including pelmet box, cupboard, drawers and the like door springs, rooling shutters etc requiring carpentry work like adjusting easing, wrought, cutting, pinning, wedging and finally making good etc and functning to seating over with each other with tightening of screws/nails, door springs etc, including petty repairs material like screws/nails, plug, grease etc to make it functional as in day to day maintenance work complete all as specified and directed.

Attending minor complaints of plumbing and sanitary fittings including water leakage from taps, WC”s, flushing cistern, urinals, wash basins, bottle traps etc and any obstruction to water supply in rooms/Qtrs, requiring plumber work with minor stores such as replacement of Brass spindle, M seal, Screws ,nailing , washers, check nuts, tightening of fittings of flushing cistern, cleaning of bolttle traps etc to make it functional and stop leaking of any type of plumbing and sanitry items as in day to day maintainence work complete all as directed.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S&F Aluminium alloy wire cloth, 0.45 mm nominal dia of wire and average width of aperture 1.40mmand fixed with beading to wooden frames complete all as specified and directed by Engineer in Charge

S&F 4mm thick plain glass panes ordinary quality and glazing with oil putty or wooden beading in squares n exc 0.5 sqm each pane complete all as specified and directed by Engineer in Charge

SIRITEL SYSTEMS PRIVATE LIMITED