SPECIAL REPAIR TO CERTAIN SMQs BLDG AT AF STN MEMAURA

Amount

Taking down cement plaster on brick walls including raking out joints, hacking for key, scrubbing down with water etc. to recare plaster complete all as directed.

Demolition of cement concrete as in ground floors & pavings not exc. 15 cm thickness (below or above G.L.) complete including removal of debries to outside MD Land complete all as specified and directed.

M&L PCC 1:4:8 type D-2 using 40 mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and as directed.

M & L for brick work using fly ash old size bricks straight or curved on plan exc. 6 M mean radius built C.M. 1:6 including demolition of brick work built in cement mortar complete all as specified and as directed.

Form work to soffit of suspended slab such as roof slab ,floor slab landing and similar work n exc 200mm thick (horizontally or sloping) complete all as specified and directed.

M&L RCC type B-1 1:2:4 (20mm graded stone aggregate ) slab supported on walls , beams, columns in slope ,roof, landing ,balconies,canopy,deck slabs & in shelves & the like including demolition of cement concrete reinforced of any description.

M & L Providing precast cement concrete type B1 (1:2:4) 20mm graded stone aggregate as in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, necessary form work and including shelves and similar articles set in cement mortar ( 1:6 ) including demolition of RCC covers complete all as specified and directed.

M&L mild steel TMT bars 10mm dia and over, cut to length, bent to shape required incl cranking, bending spirally for hoping for columns hooking ends and bindind with ms wire (annealed) not less than 0.9mm dia quality confirming to complete all as specified and directed.

M&L rendering 15mm thick in cement plaster 1:6 on surfaces other than fair faces of brick work and surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L 5mm thick rendering in CM 1:3 on ceiling, soffits, chajja projection complete all as specified and directed

M&L rendering 15mm thick in cement plaster 1:4 on surfaces fair faces of brick work and surface finished even and smooth without using extra cement complete all as specified and as directed.

M&L for applying 3mm thick birla wall care putty on plastered surfaces to make the surface even and smooth to receive new finish complete all as directed.

M&L for preparation of new (previously untreated) plastered surfaces of walls and applying two coats of cement based paint on walls, complete all as specified and directed

M&L for three coats of white wash on ceiling/Chhajja (undecorated) surfaces incl preparing of new surfaces complete all as specified and directed.

M&L for one coats of white wash on ceiling/Chhajja (decorated) surfaces incl preparing of old decorated surfaces complete all as specified and directed.

M&L for complete removal of existing treatment of wall surfaces complete all as specified and as directed.

M&L for two coats of oil bound distemper on wall surfaces over a coat of water based primer complete all as specified.

M&L for preparation of old (previously treated) plastered surfaces of walls and applying two coats of cement based paint on walls, complete all as specified and directed

M&L PCC 25mm thick 1:2:4 of type B0 using 12.5mm graded stone aggregate as in base of floors complete all as specified and as directed.

Dismantling floor, hearth or wall tiling incl. cement mortar bedding (but not backing), removing servicable tiles to store and rubbish off the premises

Roughening to surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust etc complete all as dierected.

S&F coloured non skid edge cut (jointless) ceramic tiles 7 to 8 mm thick (Square/ rectangular) area of each tile exceeding 0.06 sqm but n exc 0.11 sqm, in floors etc set and jointed in white or coloured cement to match laid over and including 15mm thick screed in CM 1:6 complete all as specified and as directed.

M & L galzed ceramic coloured tiles 450x350x7mm/ 450x300 x7mm thick, jointfree, on walls etc set & jointed in neat cement slurry & pointed in white or coloured cement to match the surfaces over &.incl 10mm thick rendering in cement mortar 1:4 for laying wall tiles etc complete all as specified and directed.

S&F non-skid joint free ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.18 Sqm but n exc 0.38 sqm set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor over and including 15mm thick screed bed in CM 1:6 complete all as specified and as directed.

S&F non-skid joint free ceramic coloured tiles 7 to 8mm thick area of each tile exceeding 0.11 Sqm but n exc 0.18 sqm set and jointed in neat cement slurry and pointed in white or coloured cement to match as in vertical surface like dado/ skirting etc including 10mm thick rendering in CM 1:4 complete all as specified and as directed.

M&L 18/20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking-plateforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified.

M&L 12mm thick granite prepolished as in corner shelf of size300mm (sides), front edge rounded fixed to wall in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including necessary cutting chases in brick wall complete all as specified.

Rounding to edges of stone slabs one edge, such as in steps, cooking plateform and other similar situation complete all as directed.

M&L for PCC 1:3:6 type C-1, (using 20mm graded stone aggregate) as in plinth protection laid in alternate panels 75mm thick finished even and smooth w/o using extra cement.

Forming contraction (Dummy) joints 65 mm deep x 10mm wide filled with sealing compound grade "A"

M&L 50mm thick cement concrete type B-0, 1:2:4 (12.5 mm graded stone aggregate) including necessary formwork and laid down in alternate panel in floor,pavings etc finishing cement concrete surface even & smooth without using extra cement complete all as specified & directed

M&L PCC type B-1, (1:2:4) using (20mm graded stone aggregate) as in coping, side kerbs etc including necessary form work complete all as specified and directed.

M&L PCC type B-1, (1:2:4) using (20mm graded stone aggregate) as in surface channels and drains etc complete all as specified and directed.

Dismantling brick tiles or terracing tiles including existing roof treatment, single layer of roofs complete all as directed.

M&L PCC 1:2:4 type B1 using 20 mm graded stone aggregate with smooth finished surface without using extra cement in terracing or padding over roof all as specified and directed.

M&L for 15mm thick screed bed in CM 1:4 mixed with water proofing compound as per manufacturer instruction , laying over green concrete surfaces, finishing the surface even and smooth with out using extra cement , complete all as specified and directed. (WPC measured separately)

Supply only liquid water proofing compound, complete all as specified and directed.

M/L for roof treatment with polymeric water proofing membrane with certain specification given below as under complete all as specified & directed) (a) Applying a coat of bitumenous primer @ 0.30 LTRs /Sqm and allow to dry. (b) applying a tack coat of hot blown bitumen grade 85/25 @ 1.20 Kg/Sqm (c) Supply and laying APP based polymeric water proofing membrace, consisting of 90 to 100 micron thick central core of HMHDPE film with standard weight not less than 3.00 kg/sqm shall be laid with 100mm side/end lap on prepared surfaces and fusing the joints with blow torch application. (d) M&L 40mm thick brick tiles laid over 20mm thick screed bed in CM 1:4. The cement mortar screed shall be mixed with polymer based liquid water proofing additive @ 5% by weight of cement or as per manufacturer's instructions and tiles joints shall be filled with CM 1:3 with crude oil as per SSR-2009 (Part-I).

S&F for mild steel rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates of Fe 410-W (Gde-E-250) quality 'A'

S & F Pre-painted Trapezoidal profile galvalume aluminium zinc coating plain steel sheet (Make: Tata bluescope/ Jindal ) 0.50mm thick (base metal thickness) of any colour having tensile strength of 550 Mpa minimum yield strength conforming to IS - 513 (1994) coated with hot dip alloy of 55% aluminium + 43.50%Zinc +1.50% silicon and finished with resin coat ( of thickness not less than 35 micron) on both surface @150gm/sqm of coating (total both surfaces) of approved colour as in roof covering/cladding, fixed with self tapping screws (make hilty/fissers), neoprene and epdm washers class 3 of AS-3566(5.5-14X5 for crest and 5.5-14X25 for valley fixed) with 150mm end lap and one corrogation side lap whereever required penetrations and lap in sheet shall be sealed by using proper sealant profile/HDPE fillers shall be provided whereever required to close voids between sheets and fastners etc. as in roof covering/ cladding in straight or curved surface in any height complete all as specified and directed. Note : 1. The colour of sheet for bldg shall be approved by GE. 2. Sheeting shall be fixed of any height.

Cutting chases in brick wall, stone concrete block or slab walls, pining in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings ,steps,cills sunshades, shelves , lintels, etc and cutting chases for concealed water tubing and making good , cutting n'exc 10 cm girth complete all as specified and directed.

S&F 15mm bore medium grade galvanised steel tubing with all fittings and fixed complete to walls and ceiling or laid in floor including taking up or down steel tubing complete all as specified and directed.

S&F 20mm bore medium grade galvanised steel tubing with all fittings and fixed complete to walls and ceiling or laid in floor including taking up or down steel tubing complete all as specified and directed.

S&F in repair 20 mm bore Gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for union and fixed complete all as specified and directed.

S&F in repair 15 mm bore dia Stop/angle valves fancy type Chromium plated screwed down , high pressure , with capston head, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repair 15mm bore dia Bib taps chromium plated fancy type with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed .

S & F in repair vitreous china hand wash basin white size 550 x 400 mm including brackets, PVC waste pipe and PVC waste coupling fixed complete all as specified and directed.

Supply only 15mm bore dia pillar tap cast copper alloy with capstan head chromium plated fancy type, screwed down high pressure, with or without lettered "Hot or Cold" with long screwed shank and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm bore stop valves (concealed type)cast copper alloy fancy type, chromium plated, with long shank and cup screwed down high pressure with crutch or butterfly handle ,screwed for iron pipe or for union as in repair all as specified.

S & F in repairs swivel shower with arm 15mm size, 195mm longbend of 45 degree with flange of PTMT any colour complete all as specified.

S&F in repair 450mm long PVC Connection 15mm size with PTMT nuts complete all as specified and directed.

S&F in repair 600x450 mm bevelled edge of slected quality glass mounted on 6 mm thick AC building board or commercial plywood and fixed to wooden plug with chromium plated brass screws and cup washers complete all as specified and directed.

S&F sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified.

S&F in repair CP Brass tubular Towel rail 20 mm dia, 60 cm long D type complete all as specified and directed

S&F in repairs vitreous china squatting pan "Orissa" pattern size 580mmx440mm white with integral foot rests including connection to trap, and to flushing pipe, anti syphonage pipe, complete all as specified and as directed.

S&F in repair 10 litre capacity PVC valveless, Syphonic action type, fluhing cistern low level,white with inlet ball valve, float and handle complete all as specified and directed.

S&F in repair 100 mm dia Stainless steel grating including jointing of solvent cement with existing floor trap complete all as specified and directed

S&F in repair sinks made of stainless steel 0.8mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 485mm x 420mm bowl size 410mm x 330mm x 160mm including sink waste coupling and 32mm size PVC waste pipe 60cm long complete all as specified and as directed by the Engineer-in-Charge.

S&F rotational moulded polethylene water tank triple layer with Puff insulation to maintain water temperature of 500 ltrs capacity ( cylindrical vertical with closed top) white colour threaded top cover hoisted in position all as pacific SSR Part- I including dismantling of water tanks complete all as specified and as directed. Make- SHEETAL "Royal Puff" / Syntex

S&F 20mm bore dia of pipe Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed (minimum weight 20mm -210 gms )complete all as specified and directed.

S&F in repair 75mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair110mm bore PVC(SWR) pipes single socketed , in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall incl PVC holding clamps complete all as directed.

S&F for PVC(SWR) floor trap, of size 75mm , with grating incl jointing with solvent cement to waste pipe fixed complete all as spd and directed.

S&F 110mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F 75mm bore PVC (SWR) bends any radius complete all as specified and as directed.

S&F 110mm bore PVC (SWR) junction single (Single T)equal or unequal complete all as specified and as directed.

Taking down chowkats or frames exc. 1.5 but n.exc 4m2 each with shutters (W/o taking off shutters from the frame) complete all as specified and as directed.

All as per item No 68.00 but n.exc 1.5 Sqm each

Taking down shutters of any description exc. 1 Sqm and nexc. 2 Sqm each complete all as specified and as directed.

Taking down shutters of any description not exc. 1 Sqm each complete all as specified and as directed.

Refixing of shutters of any description exc 1 Sqm but n exc 2 Sqm each in same opening complete all as directed.

M&L 2nd class hard wood for plain, solid, straight, chowkat and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with flue pinned at joints, supplied and fixed complete all as specified and directed by the Engineer-in-Charge.

S&F M.S work as in holdfasts., wall ties , flat iron joint pieces, plane angle cleats for securing purlins to wooden trusses or rafters etc complete all as specified and as directed.

S & F 2nd class hard wood 35 mm thick, plain framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged ), or of veneered particle board medium density, wood particle board with commercial face veneers all as specified and directed by Engr-in-Charge .

S & F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified and as directed.

S&F 35mm thick IInd class hard wood glazed skelton shutters open rebated and prepaired to recive glass,guage etc (W/o sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc size of members of sutters as specified in SSR part - I section - 8, clause 8.20 (a). S&F to chowkhat complete all as specified and as directed.

Description all as per item no 77 above but for window, ventilators etc are provided with stiles and rails as specified in SSR Part I, Section 8 clause 8.24(b) complete all as specified and as directed.

S&F in repair 18mm thick plywood boards grade BWR, type BB fixed with screw to timber frame work as in cup board shutter / shelves/cabinet fixed complete all as specified and as directed.

M&L for decorative laminate of thickness 0.9mm type1 of surface finish, colour and pattern as approved, fixed with approved adhessive as per manufacturer's instructions complete all as specified and as directed

M&L for external teak wood lipping, 6mm thick on 19mm thick boards etc fixed with nails complete all as directed.

S&F factory made solid PVC door frames of size 50mm x 47 mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube, suppling & fixing in opening as per specification & drawing.

S&F factory made solid panel PVC door shutter 30 mm thick (Style) consisting of frame made out of M S tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain coloured PCV ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail,panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cementsuppling & fixing in the frame at site as per specification & drawings.

S & F Butt hinges 100mm of stainless steel complete all as specified and as directed.

S & F Butt hinges 100mm, medium weight cold rolled mild steel complete all as specified and as directed.

S & F Butt hinges 75 mm, medium weight cold rolled mild steel complete all as specified and as directed.

S & F continuous (piano) hinges mild steel bright finished or electro galvanised having 30mm width of flap when open complete all as specified and directed..

S& F 125 mm extruded aluminum alloy handles, fabricated type anodised complete all as specified and directed..

S&F 200mm aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 100mm size aluminium alloy handles, febricated type extruded section, ISI marked complete all as specified and directed.

S&F for aluminium anodized barrel tower bolts 75 mm of extruded section and fixed.

S&F 300 mm long mild steel sliding door bolt plate type stove enamelled black with bright bolt not less then 12 mm dia incl a minimum of 6 bolt & nuts four on bolt plate and two on staple plate complete all as specified and directed

S&F for 200 mm mild steel barrel tower bolt stove enamelled black with bright bolts and fixed complete all as specified and directed

S&F for 100 mm mild steel barrel tower bolt stove enamelled black with bright bolts and fixed complete all as specified and directed

S&F 150mm size pressed handles, oval type stove enamelled black, complete all as specified and directed.

S&F 125mm size pressed handles, oval type stove enamelled black, complete all as specified and directed.

S & F 75mm long hasp and staple aluminium anodised, safety type with MS hinge pin incl. bolt to hinge plate complete all as specified and directed

S&F 300mm long ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

S&F 28mm dia fancy type MS powder coated curtain rod fixed with wooden finale stop, brackets etc to wall complete as sample approved all as specified and directed by Engr - in - charge.

S & F M.S. Framed work such as grills grating etc. with ends of bars shouldered and / or riveted into spikes, framed guard bars / railings all as directed.

S & F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

S & F in repair stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm complete all as specified and as directed.

S&F for 3mm thick Sheet glass, ordinary quality and glazing with oil putty/ wooden beads in square n exc 0.5 sq. m including hacking out old broken glass (any thickness, size, quality or description) from stee/ wooden frames or fixed with beads and & complete all as specified and directed.

S & F 3mm thick sheet glass ordinary quality and glazing with oil putty in square nexc. 0.5 sqm in each pane complete all as specified and directed.

M & L preparation of new wooden surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer on new wooden surfaces complete all as specified and directed.

M & L preparation of old wooden surfaces of any description not otherwise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of new steel or iron surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over one coat of red oxide primer complete all as specified and directed.

Taking down carefully copper/Aluminium point wiring (light/fan/socket power) complete of any size, type and including removal of battens pipe and making good to the disturbed surface to match with the existing surfaces complete all as specified and directed.

Taking down main switches/DB's along with existing board and MCB's incl. removing the same from site and making the good to the disturbed surface complete all as specified and directed.

Taking down existing sub main wiring of any type and description including removal of teak wood batten/pipe etc. complete all as specified and directed.

M & L for Point wiring complete with two runs of 1.5 sqmm single core PVC insulated FRLS cable 1100 volts grade with multi-stranded copper conductors, drawn through and including concealed medium grade conduit of not less than 20mm dia with complete accessories and including provisoin of 1.5 sq mm PVC insulated copper cable FRLS as earth continiuty conductor, fabricated steel terminal box made out of 1.60 mm thick MS sheet / 1.2 mm thick GI sheet, concealed in walls and covered with 3 mm thick hylum sheet for fixing the switches /sockets/ regulators etc.complete all as specified and directed.:-

(a)One light/fan/bell point controlled by one no, one way switch.

(b) One exhaust fan point controlled by one one way switch.

(c ) One socket outlet 6 amp controlled by one switch on the same board.

(d) One socket outlet 6 amp controlled by one switch on indepdendent board.

M & L for Point wiring with 2.5 sqmm, single core ,PVC insulated but unsheathed FRLS cable, 1100 volts grade IS -694 marked, with multi standard copper conductors and earth continuity wire with similar 2.5 Sq mm cable (incl connecting to earth dolly) drawn through and incl rigid PVC conduit and conduit accessories/fittings, fixed /laid concealed in walls/ceilings and also incl sunk type pressed steel terminal box made of 1.6mm thick MS sheat and covered with 3 mm thik laminated hylum sheet top cover for fixing 15 Amp socket out let on independent board complete all as specified and directed. Note applicable for Item No. 11 & 12 (i) Cutting chases for concealed conduit and making good surface with cement mortar is deemed to be included in unit rate as quoted under respective item.

M&L for point wiring with PVC insulated unsheathed multi stranded, single core, FRLS type, copper conductor cable of size 4 sqmm 1100 Volts including one run of PVC insulated unsheathed multi stranded, single core, FRLS type, copper conductor cable of size 4 sqmm as earth continuity conductor connected to common earth dolly, in and including PVC concealed rigid non-metallic conduit medium grade and its accessories including provn of new galvanised cencealed box with suitable back & front plate for housing the switches & sockets for one 16 Amp 3 pin socket out let point on independent board. Note - (i) Cutting chases for concealed conduit and making good in cement mortar is deemed included in unit rate.

M&L for Switch Piano, flush type single pole, one way 5 Amps.Make - Anchor/ Cona / Havells /SSK

S&F Switch flush type 15 Amp SP one way. Make:- Anchor/Legrand/Havells/Cona.

S&F Socket out let 2-in-1, 3 pin, 5&15 Amp flush type. Make:- Anchor /Legrand / Havells /cona complete all as specified and directed.

Supplying and fixing in replacement socket outlet 2 in 1, 2 & 3 pin, 5 amp, complete all as specified and directed. Make - Anchor/ Cona / Havells /SSK.

Supplying and fixing in replacement bell push, flush type, 6 amp 240 volts complete all as specified and directed.. Make - Anchor / Cona / Havells / SSK.

Supply and fixing Bell ,AC, 230 Volts Single pole. Make:- Anchor complete all as specified and directed.

S&F factory made, sheet steel distribution boards(Double door)SP&N 8 Ways,suitable for mounting MCB min 200 Amps rating copper bus bar Make- Legrand Cat part No:- 507611or equvellent in GE./ Schneider /Havells.complete all as specified and directed.

S&F of submain wiring with PVC insulated unsheathed copper conductor cable, multi stranded, single core, FRLS type, 1100 volts grade 2 x 4 sqmm complete drawn in existing conduit along with 1x 4 sqmm PVC insulated unsheathed copper conductor cable, multi stranded, single core, FRLS type for continuous earth wire and connected to common earth dolly complete all as specified and directed.

Supply and fixing MCB SPN 32 Amps 230 Volts Make:- Legrand Cat part No:- 408617 or equvallent in GE./Schneider/Havells complete all as specified and directed.

Supply and fixing MCB SP Capacity 6 to 32 Amps 230 Volts Make:-Legrand Cat part No:- 4085 (87 to 95) or equivallent in GE./Schneider/Havells complete all as specified and directed..

Supply and fixing wall mounted LED Tube light fitting complete with LED lamp of18/20 Watt (4 ft) 6000K,230 Volts provided for efficient heat dissipation and integrated electronic driver complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor calbe with 0.5 Sqmm size.Make:- C&Scat part No LTDC1220WLED/WDI /Havells cat part No:-LUMILINEBS 20 W LED 830SPCWH or equivalant in Wipro / Philips /CG complete all as specified and directed.

Supply and fixing wall mounted LED Tube light fitting complete with LED lamp of 8/10 Watt (2 ft) 6000K,230 Volts provided for efficient heat dissipation and integrated electronic driver complete with all accessories internally pre-wired and including connecting up with twin core twisted flexible copper conductor calbe with 0.5 Sqmm size. Make:-C&S Cat part NoLTTB2F10WLEDE/W/ Havells cat part No:-LUMILINEBS9WLED865SPCWH or equivalant in Wipro / Philips / CG complete all as specified and directed.

S&F ceiling rose 3 terminal PVC/Polycarbonate isolated body, 6 A 3 phase, 240 V 50 Hz complete all as specified and directed .

S. J. CONSTRUCTION

Shri Krishna Constructions

m/s pal associates

Ashirwad Contractor and Supplier

M/S PRATAP BUILDERS

M/S ALOK SRIVASTAVA