SPECIAL REPAIR TO BLDG NO P-10 A AND B AT SI LINES BHOPAL

Amount

Taking down chowkhats or frames exc 1.50 Sqm but n.exc 4.00 Sqm with shutters (without taking off shutters from the frame)

Taking down chowkhats or frames n exc 1.50 Sqm with shutters (without taking off shutters from the frame)

Taking down shutters of any descripition exc 1sqm n exc 2.00 sqm each and removing to or from store

Taking down shutters of any descripition n exc 1.00 sqm each and removing to or from store

Taking down shutters and refixing in same opening of any descripition exc 1.00 sqm and nexc 2.00 sqm each

Taking up or down 15mm bore steel tubing and connections, including cleaning for refixing or removal to store

Taking up or down 20mm bore steel tubing and connections, including cleaning for refixing or removal to store

M&L for Cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth

S&F Tubes 15mm dia, `Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors

Supplying and laying of 16 mm dia CPVC pipes SDR 11 and plain CPVC SDR 11 fittings in trenches complete all as specified

S&F Tubes 20 mm dia, `Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors

M&L for Endura joint free colour tiles 8 to 10 mm thick (square/rectangular) area of each tiles not exceeding 0.11 sqm , in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles.

Ditto all as per item No 12.00 above but on vertical surface

M&L for vitrified tiles 10 mm thick (square/ recangular) polished, area of each tiles n exceeding, 0.36 sqm,in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles.

Ditto all as per item No 14.00 above but on vertical surface icluding 10mm thk cement plaster of 1:4 as backcoat

M&L for Non skid Ceramic coloured tiles 7-8 mm thick (square / rectangular) area of each tile exc 0.11 sqm but not exc 0.18 sqm, in floor etc set and jointed in white or colour cement to match the surface of the tile complete all as specified and directed by Engr in charge.

M&L for glazed ceramic coloured tiles in vertical surfaces 350x250x7mm /450x350x7mm thick set and jointed in cement slurry with joint free including Backcoat of rendering in CM of 1:4.

Roughening surface of old cement floor by picking, sweeping clean and washing down with water to remove dust, etc

Demolition of flag stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing types

M&L for 20mm thick Granite (of any type) tiles machine cut in skirting/dado laid over cement screed and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including cutting and polishing of type

M&L for Screed bed or bedding layer of mortar 15 mm thick for laying floor finish in CM 1:4

Fixing only tiles of any type over existing floor finishes(any type) with approved tile fixture adhesive as directed by Eng-in-charge

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for making good under cills and over archs,lintels and bressummers including all pinning where necessary in cement mortar in 1:6 all as specified and directed.

S&F powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat, channel etc for fixing etc. complete all as specified and directed.

S&F 4.0 mm thick plain sheet glass ordinary quality n exc 0.50Sqm in each pane all as specified and directed.

S&F 4.0 mm thick plain sheet glass ordinary quality exc 0.50Sqm in each pane all as specified and directed.

S&F in repair of Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F of Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S&F 100mm size butt hinges medium weight cold rolled mild steel.

Ditto all as per item no 31.00 herin before but 75mm long.

S&F 100mm but hinges, extruded alluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21

S&F 150 mm long aluminium handles, cast type, anodised fixed to shutters complete all as specified and directed by Engr in charge.

Ditto all as per item no 34.00 herin before but 100 mm long

S&F 150 mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed by Engr in charge.

Ditto all as per item no 36.00 herin before but 100 mm long

S&F 35 mm Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edge of framing plain, chamfered or rounded, fitted with cut and mitred beds for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8. clause 8.20 (a); supplied and fitted to chowkhats

S&F IInd class HW factory made 35 mm thick plain framed, panelled shutter (any number of panels) with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers fitted to chowkats complete all as specified and directed.

M&L for Preparation new wooden surface of any decription and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L for Preparation old wooden surface of any decription and applying one coats of synthetic enamel painting all as specified and directed.

S&F 300mm Aluminium sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

S&F anodised aluminium fabricated grill for windows, ventilators complete fixing all as specified and directed by Engr-in-Charge

S&F 15 mm wash basin mixutre, centre hole, mixing hot & cold water, fancy type, cast copper alloy, chromimum plated with capstan head, chromium plated, screwed down high pressure, screwed for iron pipe etc and fixed in repairs complete all as specfied and directed by engr in charge. Make : Jaquar Cat No: 5001B or equivalent as approved by the GE.

S&F Soap dish holder Make: Jaquar Cat No 1131N or equivalent as approved by the GE.

S&F Towel ring Make: Jaquar Cat No 1121N or equivalent as approved by the GE.

S&F 15 mm bib cock two way with flange, cast copper alloy, fancy type, chromium plated screwed down for iron pipe and fixed in repairs complete all as specified and directed by engr in charge. Make: Jaquar Cat No: 5041 or equivalent as approved by the GE.

S&F hand shower (Health faucet) with 8mm dia 1 meter long flexible tube and wall hook fixed in repairs Make: Jaquar Cat No- 573 or equivalent as approved by the GE.

S&F chromium plated grating doom 100 mm dia with waste hole.

S&F in repairs PVC low level flushing cistern of 10 Litres with all internal fittings incl flush pipe and fixing to supply pipe.

S&F PVC connection 15mm size with PTMT nuts of length 450 mm fixing complete all as specified and directed by engr in charge.

S&F in repairs 15 mm stop cock cast copper alloy, screwed down high pressure chromium plated screwed both ends for iron pipe or for unions and fixed complete all as specified and directed

S&F in repairs 15 mm bib taps cast copper alloy, screwed down high pressure chromium plated screwed for iron pipe and fixed complete all as specified and directed.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, as specified and directed.

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tube for top & bottom rails. MS frame shall be covered with heat moulded palin colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the MS frame wlded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing tin the frame at site as specified and directed.

M&L PVC (SWR) floor trap plain with grating incl jointing with solvent cement 75mm bore complete all as specified and direcetd.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store. (measured overall as fixed along the centre line over fitting and accessories)

S&F PVC (SWR) pipes 75 mm bore single socketed in any length with rubber rings joints laid in trenches.

Ditto all as per item No 58.00 above but 110mm bore.

S&F PVC (SWR) bend of the following bore 75 mm

S&F PVC (SWR) bend of the following bore 110 mm

S&F PVC (SWR) branch piece single (Y) equal or unequal bend the following bore 75 mm.

S&F PVC (SWR) branch piece single (Y) equal or unequal bend the following bore 110 mm.

S&F PVC (SWR) junction single (single 'T') equal or unequal of the following bore 75 mm.

S&F PVC(SWR) junction single (single 'T') equal or unequal of the following bore 110 mm

S&F PVC(SWR) vent cowl for following bore 75mm

S&F PVC(SWR) vent cowl for following bore 110mm

S&F 400mm x 350mm mirror with PVC cabinet of standard including all fittings as accessories all as specified and directed.

S&F in repairs Stainless steel sink, 1.00mm thick for kitchen, with plug, washers and wastes/coupling, including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm with bowl size 410mmx 330mmx 160mm fixed complete all as specified and directed.

S&F in repairs Plastic water closet seat cover, White colour, closed pattern with flat bottom, and mild steel chromium plated for aluminised hinging device complete.

S&F tubular towel rail chromium plated 20 mm dia D type 60 cm long between flanges complete all as specified and directed by engr in charge

Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed

S&F in repair of vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)

S&F in repair to Chromium plated shower roses with or without swivel joints, any size, including fixing to steel pipe or union

S&F in repair CP fancy type Bib taps, cast copper ally with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S&F Glass Corner, size nexc 250mm with CP bracket

S&F in repair of sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long

S&F in repair towel Ring of PTMT fixed with and including Chromium plated brass screws and wooden/ plastic cleats (Minimum weight 90 gms)

S& F in repair toilet paper holder, viterous China, box type

S&F Jet Spray with connecting pieces including all necessary fittings and accessories as directed by Engr in Charge

S&F in repair looking mirror approved quality with wooden back and edge, complete polishing , fixing in repairs complete all as specified and directed.

S&F Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed but fancy type 15 mm in dia in repairs

S&F Angle Cock, cast copper alloy screwed pressure, with crutch of butterfly handle, screwed both ends for iron pipe for unions and fixed but fancy type ,15 mm in dia

M&L for 2nd Class hardwood, Plain fillets, square, rectangular or triangular in section, clean sawn, secured with mills or brads, not exceding 3 Sq.cm sectional area

M&L for prelaminated partcle board 9 mm thick, exterior grade, prelaminated both side with decorative choice lamination fixed with nails to aluminium framed work fixed in repair.

M&L for prelaminated partcle board 18/19 mm thick, exterior grade, prelaminated both side with decorative choice lamination fixed with nails to aluminium framed work fixed in repair.

S&F magnetic catches for cupboards with plastic body and striking plate not less than 40mm including letting in and fixed complete all as specified and directed

S&F 75mm brass handle , cast type, polished bright complete all as specified and directed by Engr-in-Charge

S&F 40mm wide of flap continuous (piano) hinges, brass , bright finish

M&L for 15 mm thick rendering in cm 1:4 on fair aces of bricks walls surface finished even and smooth without using extra cement including water proofing compound all as specified and directed. Note: Water proofing compound shall be measured and paid seperately.

M&L for 15mm thick rendering in CM 1:6 on fair face of brick walls/ concrete surfaces finished even and smooth without using extra cement all as specified and directed.

Integral water profing compound

Taking down cement plaster, terrazzo/cement dado, skirting etc of any description on brick/stone walls, concrete surfaces etc including racking out joints, hacking for key, scrubbing down with water etc

M&L for Preparation of newly plastered surface and applying two coats of oil emulsion distemper over one coat of white cement based putty all as specified and directed. Note: Thickness of putty shall be as per manufacturer instruction.

M&L for preparation of newly plastered surface of wall and applying two coats of exterior weather proof water base emulsion paint over and incl a coat white of cement based putty, complete all as specified & directed by the Engineer in charge. Make: ASIAN (Apex ) or equivalent as approved by GE. Note:- Exterior Acrylic Emulsion Paint only, Should be carried out by any of approved Company/ firm (Apex of M/S Asian Paint or Equivalent) Note: Thickness of putty shall be as per manufacturer instruction.

M&L for complete removal of existing treatment and applying two coats of exterior weather proof water base emulsion paint over and incl a coat of white cement based putty all as specified and directed. Make: ASIAN (Apex) or Equivalent as approved by GE. Note:- Exterior Acrylic Emulsion Paint only, Should be carried out by any of approved Company /firm (Apex of M/S Asian Paint or Equivalent) Note: Thickness of putty shall be as per manufacturer instruction.

M&L for complete removal existing treatment and applying two coats of oil emulsion distemper over one coat of white cement based putty all as specified and directed. Note: Thickness of putty shall be as per manufacturer instruction.

M&L for wall care putty on wall/ ceiling as specified and directed. Note: Thickness of putty shall be as per manufacturer instruction.

M&L for 75 mm thick PCC 1:3:6 type C-2 (using 40mm graded crushed stone aggregate) as in plinth protection

Demolition of concrete in ground floors and pavings (unreinforced) nexc 15 cm thickness (below or above ground level).

Demolition of brick work or stone masonry built in cement mortar.

M&L for Brick work with subclass 'B' bricks, straight or curved on plan to any radius in half brick thick walls built in CM 1:4 using modular bricks all as specified and directed

M&L for brick work with sub class modular 'B' bricks in cm 1:6 using modular bricks straight or curved on plan to any radius.

S&F in repair 20mm dia draphory rod decorative type incl brackets of approved quality as in complete, all as specified and directed

M&L for two coat of varnishing to new surface of any description, nexc 10cm in width or girth.

Dismantling of Asbestos cement (corrugated ted, semi corrugated, etc.) sheets in roof coverings.

Dismantling timber fillets, rails, posts, rafters, purlins, etc. under 40 Sqcm in section in framed work.

Dismantling timber scantling 40 sqcm and over in section, in any position in unframed work.

S&F MS rolled section/tubular sections in purling, cross, beam, rafter,posts etc. incl connected cleats, hold fasts etc of grade conforming to Fe 410-O or Fe 310-O all as specified and direcetd. Note: Weight shall be verified by the GE.

S&F MS wind ties for roof truss including necessary drilling bolting as riveting etc and similar work to FE 410-S or FE 310-S all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based corrrugated steel sheet 0.50 mm thick of any color having tensile strength of 550 Mpa as in roof covering /cladding to wall fixed with self-tapping screws on angle iron frame of each side as directed by Engr-in-Charge.

Ditto all as per item No. 111.00 above but plain sheet.

M&L for preparation of old painted surfaces of steel and iron surface of any description and applying two coats of synthetic enamel paint complete as specified and directed.

M&L for preparation of new steel surface of any description and applying two coat of synthetic enamel paint over a coat of red oxide primer all as specified and directed

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forget into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

Dismantling structural steel work including doors, gates but excluding framed truss etc.

M&L for machine pressed precast concrete inter locking paver block (Reflective type) in any shape and size confirming to IS-15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment as specified and directed.

S&F in repair stainless steel plate rack complete assembled set of (Size: 31 x 36 x 10 inch) fixed with screws as specified and directed

S&F in repair stainless steel plate rack complete assembled set of (Size: 24 x 30 x 10 inch) fixed with screws as specified and directed

M&l for ShaliCryl ® 215 single component, UV resistant, unique elastomeric, high build exterior waterproofing coating based on a revolutionary acrylic polymer with quick-set capabilities to resist moisture attack.

Surface Preparation :- Remove all loose and foreign materials, if any, by a wash with a jet of air / water. • Repair structural defects before application of ShaliCryl® 215. • Fill voids and undulation area with Polymer Mortar made out of ShaliSBR Latex, Water, Cement and Sand in the Ratio of 1:1:5:12.5. • Fill cracks up to 3 mm with PlastiSeal and cracks over 3 mm with PlastiSeal P after opening the crack to a “V” cut. • In case of any poor plaster surface in existence (for old building), remove the same and corrected with new cement : sand in the ratio of 1 : 4 admixed with ShaliPlast LW+ @ 200 ml / bag of cement.

Primer Application :- Apply ShaliPrime WB as Primer after dilution with potable water in the ratio 1:0.5 for a theoretical Coverage 8-10 m2 / L of the mix and allow it to dry for 3 – 4 hrs. post elimination of undulation, roughness of concrete, joint marks, Voids and any other surface correction.

Application of Material • Apply first coat of ShaliCryl® 215 over the primed surface @ 160 ml / m2 . Add maximum of 10% potable water by volume for the first coat only, if required, to have brushable consistency only. • Allow the applied coating to dry 6 – 8 hrs of application. • Apply second coat of ShaliCryl® 215 without dilution over dried first coat @ 140 ml / m2 and allow it to dry. • Do not undertake any further work over the coated area within 72 hrs of final coat. • A coat of 100 micron of ShaliCryl TC 100 will improve water / dust repellent property.

Providing and injecting chemical emulsion for Post Constructional Anti-termite Treatment along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

M&L for treatment of soil under existing floors using emulsion @ one litre per litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors.

Raking out joints/ pointing to squared rubble masonry, coursed or uncoursed in cement or cement lime mortar

M&L for Struck pointing to squared rubble masonary , cousred or uncoursed in cement mortar 1:4.

Cutting holes in brick walls exc half brick but not exc one brick in cement mortar ore cement lime mortor for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required as specified and directed.

S&F in repairs vitreous china squatting pan of Orissa pattern 580x440 mm white with integral foot rests (excluding flushing cistern and flush pipe) all as specified and directed.

S&F IInd class HW for plain, solid, straight chowkhat and framed, rough/ framed rebated on the solid, rounded, or chamfer, put together with glue pinned at joint, all as specified and directed.

M&L for Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing & mirror polishing complete and including screed bed or bedding layer of mortar 20 mm thick for laying floor finish in CM 1:6 all as specified and directed. Note:- Kota Stone should be in one piece and including making of three liunes and moulding etc complete

Ditto all as per Item No. 128.00 above in riser of steps, skirting, dado and pillar laid over cement screed and jointed including 10 mm thick rendering in CM 1:4 for back coat of wall tiling complete all as specified and directed.

M&L for non shrink cementious micro concrete for jacketing on surface of columns, beams and similar structural members with 5 to 12mm stone aggregate in the ratio as per manufacturer's instructions laid to as thickness as directed by Engineer-in-Charge including applying curing compound and use and waste of necessary scaffolding as required.

S&F galvanised cold rolled steel section framed work size 600x600 mm grid size 24x38x0.60 mm Tee (bottom precoated) and 24x24x0.50 mm thick wall angle galvanised cold rolled steel section incl expansions fasteners as in ceiling Make: Gabson or equivalent as approved by the GE.

S&F 6mm thick Asbestos free calcium silicate board of size 600x600 mm fixed to frame of galvanised cold rolled steel frame work as in ceiling including applying two coats of oil bound distemper over a coat of primer all as specified and directed.

S&F GI frame work size of grid 605 mm x 605 mm for seamless ceiling comprising of GI perimeter channel 0.55 mm thick with two unequal flanges of 20 and 30 mm and web of 27 mm fixed to surrounding wall using nylong sleeves and screws at 450 mm centre to centre / intermediate channel 0.9 mm thick having two eaqual flanges of 15 mm each and web of 45 mm suspended from soffit at approx 900 mm centre to centre with GI cleat and steel expansion fasteners with and including ceiling section (not exc 1.2 m length) of 0.55 mm thickness having kuled web of 50 mm and flange of 26 mm each with lips of 10.5 mm fixed to the intermediate channel with connecting clips across the intermediate channel at 457 mm centre to centre.

M&L for Providing and fixing 10mm thick plaster of paris ceiling (Gypsum anhydrous) to curved surface fot any shunk and raised moulding over GI frame work and reinforced with G.I. wire mesh Note: Fillets and G.I. wire mesh shall be measured & paid seperately.

Dismantling wall and ceiling boards (fibre, pulp, insultion, etc) or insulation boards/ slabs/ blankets,any thickness,including cover fillets.

Excavation in trenches n.exe 1.5m wide and n.exe 1.5m deep for laying pipe line incl getting out in hard/ dense soil complete all as specified and directed.

Returning filling in incl spreading watering and well ramming in layers in hard/dense soil each not exceeding 25cm thick complete all as specified.

Removing surplus soil to a distance not exe 50 mtr and depositing where directed at a level not exe 1.5 m above the starting point complete all as specified and directed.

Dismantling/ taking out to old rusted/ blocked /corroded, unsv pipe line from trenches and wall/floor etc with complete fittings all as specified and directed by Engineer in Charge . Size of GI tubing :- (a) 25mm dia bore

50 mm bore

25 mm bore

Supply, fixing & laying in repairs GI tubing medium grade with one socket both end threaded in any length including cutting threading connection in new or old position and all type of GI new fittings for laid in trenches/wall/ceiling/ floor all as specified and directed by Engineer in Charge . Size of GI tubing :-

50 mm bore

25 mm bore

Re-fixing and laying only of old steel water tubing and returning of old screw threads as required in trench ,in new or old positions including descaling cleaning for fixing of fittings such as elbow sockets, union, reducer all required as directed by Engineer-in charge for the size of GI tubing :-

50 mm bore

25 mm bore

20 mm bore

S&F Gun metal globe or gate valves, conf to IS 778 with iron wheel head, screwed both ends for iron pipe and fixed in existing or new position for size 25 mm bore , including taking out existing UNSV Gun metal globe all as specified and directed by Engineer in Charge

50 mm bore

25 mm bore

20 mm bore

Supply and fiixing and hosting in repair PVC water trank with led in position rotaional moulded polyethylene ISI mark water storage tanks (cylindrical vertical with closed top) including dismantling existing tank making inlet outlet over flow wash out pipes of any size and length with fitting such as barrale nipple check nut gasket of suitable sizes , tank capacity 1000 ltrs all as specified and directed by Engineer in Charge

M&L for PTMT float valve high pressure with high density plastic ball, with epoxy coated Aluminium rod screwed for iron pipe and fixed in all , including taking down existing u/s float valve size 25 mm bore all as specified and directed by Engineer in Charge

Taking down carefully the old U/S aluminum point wiring (light, fan, socket or power) complete fitting such as switches ,ceiling roses ,pendants, sockets, regulators, wall light fittigs , tube light fittings, surface light fitting , ceiling light fittings , any types of fittings etc and making good disturbed surfaces of walls including necessary touch up with the same finishes to surrounding wall, floors etc complete all as specified and directed by Engineer in charge .

M & L for point wiring complete for light/ fan on independent /combine board with cable 1.5 sqmm (Nominal area) FRLS PVC insulated multistranded unsheathed copper conductor, drawn in PVC casing & caping and including juction covers and junction boxes , sunken cast iron/ pressed steel terminal boxes duly grouted in breicks cement or wooden planks wall and painted with red oxide metal primer for mounting of switches, sockets,fan regulator with 3 mm thick plastic laminated sheet top cover fixed with brass screwed and cup washers including making good to disturbed surfaces of wall in CM 1:3 with white/colour wash as per adjoining specifications including provision of continuous earth continuity wire of 1.5 sqmm copper PVC insulated insulated FRLS cable for one light/ fan point controlled by one switch and connected to common earth dolly, complete all as specified and direced by the Engineer in charge.

Ditto all as per Srl item No - 146 here in before but for one switch socket combination 5/6 amp on independent board complete all as specified and directed by Engineer - in - Charge.

Ditto all as per Srl item No - 146 here in before but for one three pin socket outlet 5 Amp on same board with other switches complete all as specified and directed by Engineer - in - Charge.

Ditto all as per Srl item No - 146 here in before but for one switch socket combination 6 pin 5/ 15 Amps on independent board with wire of size 2.5 Sqmm and 2.5 Sqmm as earth wire.complete all as specified and directed by Engineer - in - Charge.

S & F switch piano flush type 5/6 Amps single pole one way complete all as specified and directed by Engineer - in - Charge.

S&F in repair bell push flush type SP 5 Amp complete all as specified and directed by Engineer - in - Charge.

S&F switch socket combination 5 pin, type 5/6 Amps flush type complete all as specified and directed by Engineer - in - Charge

S&F Socket outlet 5 pin 5 Amps flush type complete all as specified and directed by Engineer - in - Charge.

S&F switch socket combination , 5/16 Amps 5-in-1 , flush type complete all as specified and directed by Engineer - in - Charge.

S&F ceiling rose surface bakelite three terminals complete all as specified and directed by Engineer - in - Charge.

S&F in repair electric bell single phase suitable for 240 V complete all as specified and directed by Engineer - in - Charge.

Supply & fixing LED tube light complete fitting, surface mounted lumanaires, 1 x 18 W, 240V. Decorative ultra slim round /squar profile LED lighting fixture with extruded polycarbonate , environmental friendly, energy efficient ready to use pack.with bipin holders, LED lamps,connector block, etc. complete with all accessories internally pre-wired and including connecting up with flexible copper conductor cable with suitable size complete all as specified and directed by Engineer in charge . Make: Havells LHEXBLP7N1W018 or equivalant in C&G/ Bajaj/ Surya

Supply & fixing LED tube light complete fitting, surface mounted lumanaires, 1 x 9 W, 240V. Decorative ultra slim round /squar profile LED lighting fixture with extruded polycarbonate , environmental friendly, energy efficient ready to use pack.with bipin holders, LED lamps,connector block, etc. complete with all accessories internally pre-wired and including connecting up with flexible copper conductor cable with suitable size complete all as specified and directed by Engineer in charge . Make : Havells LHEXBLP7N1W009 or equivalant in C&G/ Bajaj/ Surya)

Refixing of serviceable light fitting any type any make and size with connection complete all as specified and directed by Engineer - in - Charge.

S & F angle holder insulated body with back plate for conduit fittings complete all as specified and directed by Engineer - in - Charge.

S & F LED lamp 10 Watt B22 CDL complete all as specified and directed by Engineer in Charge

Supply & fixing Decorative light fixture made up of polycarbonate including 12 Watt LED lamp complete with all accessories internally pre-wired and including connecting up with flexible copper conductor cable with suitable size complete all as specified and directed by Engineer in charge . Make : Havells LHOFTE1TZW012 or equivalant in C&G/ Bajaj/ Surya)

S&F building security light fitting made up of pressure die cast aluminium housing with high effcient LED as lighting source and PC over having top opening seperate driver compartment with IP-66 protection and impact resistance of IK07 with suitable galvanized iron pipe “light grade” brackets1 mtr length bent to shape to obtained required shape including clamps, nuts / bots / washers etc connecting with suitable flexible copper wire of size 23/0.0076 complete all as specified and directed by Engineer - in - Charge Make: Havells Cat NO ENDURAPEARLSL20WLED757SASYTOPCMP/ Bajaj /Surya)

S&F Exhaust fan 230 mm sweep metal body with louvers 240V complete with all accessories including making hole in stone/brick wall grouting suitable size with nuts/bolts & making good in all respects complete all as specified and directed by Engineer in charge . Make: Havells Ventilair DB- NEO or equivalent in C&G/ Bajaj/ Usha)

S&F ceiling fan 1200 mm sweep ,240V complete with all accessories all as specified and directed by Engineer in charge . Make: Havells model - "Velocity" or equivalent in C&G/ Bajaj/ Usha)

S&F stepped type electronic fan regulator complete all as specified and directed by Engineer - in - Charge.

S&F in replacement of sub-main wiring with two single core cables PVC insulated and un-sheathed 6 sqmm (Nominal Area) FRLS stranded copper conductor drawn in surface PVC casing and caping size 20mm/ PVC conduict dia 20mm including 4.00 Sq mm (Nominal Area) copper cable as earth continuity conductor making good the disturbed surfaces and white wash or colour wash as per adjoining specifications , necessary junction box with covers including connections, PVC flexible pipes to be used while connecting the cable in DBs/Pannel, including taking down old unsv submain wiring complete all as specified and directed by Engineer - in - Charge. Note : PVC cable and PVC conduit / PVC casing and caping shall be ISI marked.

Supply and fixing factory made epoxy powder coated Distribution Board TP & N 4 ways ( VTPN MCCB DB ) and space for MCCB 125 Amp as In comer, with metal door ( IP-43 protection ) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including Isolated Neutral Bar, Insulated busbar assembly, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockouts including taking down old unsv VTPN DB complete all as specified and directed by Engineer - in - Charge. Make: Legrand/Schneider or equivalent as approved by the GE. Note:- Rate of MCCB are excluding in the rate quoted for this item.

Supply & fix MCCB 125 Amp, 3 Pole breaking capacity 16 KA with complete electrical connections by appropriate size of copper lugs , including taking down old unsv MCCB complete all as specified and directed by the Engr-in-Charge.

S & F in repairs sheet metal enclosure double door type surface mounted concealed in wall 8 ways, 240 Volts, ISI marked 200 amps bus bar dust and vermin proof suitable for incorporation MCBs and isolators etc including taking down old unsv DB complete all as specified and directed by Engineer - in - Charge.

S & F in repairs MCB SP suitable for 240 volts, AC supply 6 to 32 Amps , with over load and short circuit protection and rupturing capacity not less than 10KA including taking down old unsv MCB SP complete all as specified and directed by Engineer - in - Charge.

S & F in repairs MCB SP suitable for 240 volts, AC supply 40 to 63 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA ,including taking down old unsv MCB SP complete all as specified and directed by Engineer - in - Charge.

S & F in repairs MCB SPN suitable for 240 volts, AC supply 6 to 32 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA , including taking down old unsv MCB SPN complete all as specified and directed by Engineer - in - Charge.

S & F in repairs MCB SPN suitable for 240 volts, AC supply 40 to 63 Amps, with over load and short circuit protection and rupturing capacity not less than 10KA including taking down old unsv MCB SPN complete all as specified and directed by Engineer - in - Charge.

Earthing complete with galvanized steel earth plate electrode 60 cm x 60 cm x 6 mm thick, burried directly in ground (earth pit not less than 2.25 Mtr deep below ground level) with top edge of plate not less than 1.5 Mtr below normal ground level, connected to galvanized earth lead 4 mm dia by means of nuts, bolts, check nuts and washers of galvanized iron along with galvanized iron protection pipe 15mm dia “medium grade” from plate to earth point all as shown in electrical plate No- 5 of SSR Part – I 2009 including alternate layer of charcoal and salt around the electrode 150 mm thick and excavation in any soil, returning , refilling and removal of surplus soil up to the distance of 50 mtr earth pit made out of PCC 1:2:4 type - B-1 alongwith 40 mm thick cover of RCC ( 1:2:4) reinforced with XPM ( Weight not less than 4 Kg/sqm) , watering arrangement, funnel and wire mesh, 20mm galvanized iron pipe “light grade” used for watering etc. complete and testing con comptetion all as specified and directed by Engineer-in-Charge.

Excavation in trenches n. exc. 1.5Mtr width n.exc 1.5 Mtr in depth for laying of cables & foundation of poles, stay assembly and getting cut in soft/loose of soil.

Returning, filling in including spreading levelling , watering and well ramming in layers not exc. 25cm in any type soil

M&L for GI pipe (Light grade ) for protection of LT cable fixed to walls/ poles/road crossing including clamps 25x3mm incl nut bolts and washers complete of size 50 mm bore incl taking down unserviceable existing pipe all as specified and directed by Engineer in Charge

M&L for cutting of bituminious road for laying of cable along with GI pipe all as specified and directed by Engineer in Charge

S&F 1100 volt graded heavy duty XLPE cable with PVC insulated aluminium conductor served with an inner sheathing of PVC tape armoured with galvanized steel strip or wire and overall PVC sheathed of size 25 Sqmm normal corss section 3.5 core laid in trenches fixed to pole or passing through pipes incl all necessary clamps nuts, bolts and washers complete all as specified and directed by Engineer in Charge.

M&L for Sand cushioning to cable with dry fine sand in trenches 8 cm below the cable and 15cm above the cable after laying and testing complete all as specified and directed by Engineer in Charge Note :- Punned thickness shall be measured & paid.

M&L for Bricks laid in trenches flat with width equal to length of bricks for cble protection with well burnt sub class B bricks, complete all as specified and directed by Engineer in Charge.

Note for all items: All items shall be executed as specified and directed by Engr-in-charge.

RAJPATI CONSTRUCTION

PADAMSHRI CONSTRUCTION CO

Samaksh Enterprises

M/S RAKESH TRADERS

SATHI ENTERPRISES

SHIV SHANKAR MISHRA

Vee kay construction