SPECIAL REPAIRS TO BUILDING No H 09 JCOs CLUB AND LXXXII MNS OFFICERS MESS OF MH WELLINGTON UNDER GE WELLINGTON

Amount

Dismantling of single layer Mangalore pattern tiles or similar pattern tiles on roof all as specified and directed.

Dismantling of single layer Mangalore pattern tiles or similar pattern tiles in ridge of roofing fixed with cement mortar complete all as specified and directed.

Dismantling of timber scantling 40 sqcm and over in sections in any position in chajjas as in unframed works all as specified and directed.

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with self tapping screws all as specified and directed.

Pre- painted galvalume aluminum zinc coating GI based Plain steel sheet as in ridge of 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering, on chajjas and wall cladding fixed with self tapping screws all as specified and directed.

Mild steel Rolled sections as in main and cross beams, hip and jack rafters, purlins when connected to main rafters and running rails and guides for sliding doors, fixed with angles, cleats or other connecting plates conforming to Fe-290 (Gde-E-165) all as specified and directed.

Preparation of new or untreated steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer all as specified and directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swannecks ect all as specified and as directed.

PVC (SWR) pipe 160mm bore as in half round gutters including fixing with mild steel clamps suitable for Galvalume Roof sheets/ AC sheets roof, complete all as specified and as directed.

PVC 160mm dia drop ends / stop end suitable for 180mm half round valley gutter complete all as specified and as directed.

PVC (SWR) 160mm dia bore pipe single socketed in any length, with rubber ring joint fixed to walls, complete all as specified and as directed.

PVC (SWR) bends any radius 160mm dia bore pipe all as specified and as directed.

Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised wire staple and fixed in repairs all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stones, concrete or brick surrounds, glazed with putty or fixed with beads supply and fix new sheet glass 3mm thick ordinary quality and glazing with oil putty and beads in square not exceeding 0.5 sqm in each pane all as specified and as directed

Resecuring or easying and adjusting without taking down shutter of any description not exceeding 1 sqm each all as specified and directed.

Resecuring or easying and adjusting without taking down shutter of any description exceeding 1 sqm and not exceeding 2 sqm each all as specified and directed.

Preparation of new wooden surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer all as specified and as directed.

Preparation of old painted wooden surfaces and wood based materials of any description not other wise over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

Preparation of old painted steel surfaces and steel based materials of any description not other wise over 10 cm width or girth and applying one coat of synthetic enamel paint all as specified and directed.

Demolition of cement concrete un-reinforced in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) all as specified and directed.

Demolition of stone slabs and tiles laid, bedded and pointed in any mortar, etc, complete all as specified and directed.

Dismantling, floor hearth or wall tiling including cement mortar bedding (but not backing) and rubbish off the premises complete all as specified and as directed.

Cement concrete type B-0, 1:2:4 using 12.5mm graded stone aggregate, 25mm thick as in floor all as specified and directed.

Coloured Non Skid ceramic tiles 7 to 8mm thick ( Square/Rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 Sqm as in floors etc., and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed in CM 1:4 including spacers with epoxy grouting complete all as specified and as directed.

Vitrified Ceramic Tile 10mm thick (Square/Rectangular) polished area of each tile not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of mortar in cement mortar 1:4 complete all as specified and as directed.

Vitrified coloured ceramic tiles 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 Sqm, as in skirting/, dadoo etc. set and jointed in neat cement slurry and pointed in white or coloured cement slurry to match over and including 10mm cement plaster as backing coat in cement mortar 1:4 complete all as specified and directed.

Coloured Glazed ceramic tiles in vertical surfaces 450x350x7mm/ 300x600x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick plaster in cement mortar 1:4 on fair face of brick or concrete surface

Granite slab 20mm thick machine cut, as in floor bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing over and including 15mm thick screed in cement mortar 1:4 all as specified and directed.

18 to 20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigmet to match with shade of granite over and including 15mm thick screed in cement mortar 1:4 all as specified and directed.

Vitreous china Counter Wash Hand Basin with fixing accessories, any shape size not less than 480x370x200 mm including brass chromium plated perforated waste coupling/fittings 32 mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, PVC waste pipe of 32 mm bore and of suitable length, 15 mm bore Pillar Tap, cast copper alloy with capstan heads, chromium plated, fancy type, screwed down high pressure with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly nuts, screwed for iron pipe and PVC connection 15 mm size with PTMT nuts of length 450 mm and fixed complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern) white with P or S trap including flushing pipe, seat and PVC seat cover (white) closed pattern with flat bottom and cover brass chromium plated hinging device, including connection to drain and to flushing pipe, antisyhonage pipe etc complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets including fixed in repairs complete all as specified and directed.

PVC (SWR) floor/ Nahani trap 75mm outer dia, plain with grating including jointing to waste pipe with solvent cement all as specified and as directed.

Central hole basin mixer for mixing hot and cold water without popup waste system with 450mm long braided hoses screwed down for iron pipe 15mm dia bore complete all as specified and directed. Make: Jaquar, Continental Cat No CQT-23167B or equivalent

Brass CP wall mixer for mixing hot & cold water with provision of over head shower with 115mm long bend pipe on upper side connecting legs and wall flanges screwed down for iron pipe 15mm dia bore and fixed in repairs complete all as specified and directed. Make: Jaquar, Clarion (Cat No CQT-23273UPR) or equivalent.

Angular stop cock with wall flange for 15mm dia of chorumium plated fancy type in repairs complete all as specified and directed. Make: Cat No CON-059KN of JAQUAR or Equivalent

PVC connections 15mm size with PTMT nuts of length 450mm and fixed in repairs complete all as specified and directed.

Over head shower rose 200 mm X 200 mm square shape single flow with shower arm square 300 mm long and fixed in repairs complete all as specified and as directed. Make: Jaquar or equivalent

Bib tap fancy type chromium plated fixed to 15mm bore in repairs complete including fixed in reapirs all as specified and directed.

Health Faucet with 8mm dia, 1 m long flexible tube and wall hook with back flow preventer and fixed in repair all as specified and as directed.

Soap dish complete fixed in repairs all as specified and directed. Make: JAQUAR or equivalent

Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges and fixed in repairs all as specified and directed.

Fancy type decorative drapery rod 20 mm dia including side caps and brackets, as in repairs complete all as specified and directed.

CP toilet paper roll holder complete fixed in repairs all as specified and as directed.

Taking up or down steel tubing and connections including cleaning for refixing or removal to store for 15mm bore pipe all as specified and directed

Taking up or down steel tubing and connections including cleaning for refixing or removal to store for 20mm bore pipe all as specified and directed

Supply, laying and testing concealed steel water tubing 15mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) complete all as specified and directed. Note: Cuting chasing shall be included in the quoted rate.

Supply, laying and testing concealed steel water tubing 20mm medium grade galvanised with all fittings including short lengths, fixed to walls, concealed in wall and ceiling or laid in floor complete with all fittings (such as bends, elbows, tees, short pieces, connectors, back nuts, diminishing pieces, caps and plugs, unions etc) complete all as specified and directed. Note: Cuting chasing shall be included in the quoted rate.

Dismantling of wall/ ceiling boards (fibre, pulp, insulation, etc) or insulation boards/ slabs/ blankets, any thickness, including cover fillets and frame work all as specified and directed.

PVC insulation solid panel 10mm thick of size 600x600mm fixed to aluminium snap grid complete all as specified and directed. Note: Frame work for ceiling shall be measured and paid separately.

605x605mm grid size Anodised aluminium snap grid frame work for false ceiling complete all as specified and directed.

Demolition of Brickwork, stone / boulder masonry built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as specified and directed.

Pre-cast cement concrete block masnory with solid block exceeding 10cm in width and setting in cment mortar 1:6 type C1 1:3:6 using 20mm graded stone aggregate complete all as specified and directed

Taking down cement plaster of any descreption and in any position of brick or concrete surfaces and racking out joints hacking for key, scrubbing down with water etc and removal of rubbish off all as specified and directed.

Rendering 15mm thick in cement mortar 1:4 over fair faces of brick masonry / concrete surfaces and finished even and smooth without using extra cement compete as specified and directed.

Plastering 15mm thick in cement mortar 1:4 with WPC in two layer of stone wall surfaces finished even and smooth without using extra cement complete all as specified.

Supply only liquid water proofing compound all as specified and directed.

Preparation of new plastered surfaces of wall and applying two coats of Exterior Emulsion Paint (Anti Fungal) white or tinted over a coat of primer complete all as specified and as directed. Note: 1. Rates shall be quoted inclusive of required scafolding for a height upto 10 meters buildings inclusive of working of item No 1 & 2 hereinabefore.

Preparation of newly treated surfaces of walls and applying two coats of oil bound distember over a coat of wall care putty including primer complete all as specified and directed.

Complete removal of existing treatment of wall surfaces and applying one coats of primer (water thinable/ solvent thinable) over and including one coat of putty in two layers 2-3mm thick even and smooth and applying two coats of oil bound emulsion distemper (washable) complete all as specified and directed.

Preparation of old plastered surfaces of wall after removal of existing treatment and applying one coat of external wall putty with one coat of primer and two coats of antifungal paint weather coating on external wall of Asian Paints Apex ultinma or equivalent make as per list of makes in PS as approved by GE complete all as specified and directed.

Dismantling boarding/ ceiling board of any description fixed in any position with nails complete all as specified and directed.

Taking down chowkat or frame with shutter (without taking of shutters from the frames) area not exceeding 1.5 Sq mtr each all as specified and directed.

Taking down chowkat or frame with shutter (without taking off shutters from the frames) area exceeding 1.5 Sq mtr but not exceeding 4 Sq mtr all as specified and directed.

20mm thick Boarding of 2nd class soft wood, planed one side with butt joint, fixed with nails in any situation, complete all as specified and directed.

2nd class hard wood (sal / Hollock) wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid rounded or chamfered put together with glue, pinned at joint complete all as specified and as directed.

35mm thick second class HW plain, framed, panelled shutters (any No of panels) with veneered particle board medium density, 12mm thick complete all as specified and directed.

35mm thick second class hardwood glazed and skeleton door shutters open rebated and prepared to receive glass, gauze etc, (without sash bars), edges of framing plain, chamfered or rounded with cut and mitred beads for securing glass/gauges, size of members of shutter as specified in SSR Part-I section 8, clause 8.24 (a) complete all as specified and directed.

Factory made UPVC white colour sliding window three track, area not exceeding 2.00 Sqm each made of extruded profiles with wall thickness of 2.3mm (± 0.2mm) window profile with hollow section with multi chamber frame (88mm x 85mm) sliding sash (42mm x 67mm) sliding mesh sash (42mm x 57mm) sliding mesh sash (42mm x 57mm) sliding interlock (one vertical length in each shutters) (45.5mm x 28mm) Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc, making arrangement for fixing of hardware EPDM gasket, 1.2 (± 0.2mm) thick galvanised steel frame (30mm x 18mm) 2 Nos sliding sash (30mm x 18mm) sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, hardware (Touch Lock of zinc alloyed (white powder coated) steel roller system stainless stell wire cloth 0.36mm nominal dia of wire and average width of aperture 140mm and required accessories all as specified and directed. Note: The unit rate quoted by contractor excludes cost of glass and includes all other connected accessories and wire mesh. The net opening will be measured for payment purpose.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube,supplying and fixing in opening as per specification and drawing all as specified and directed.

Factory made solid panel PVC door shutter 30mm (Style) consisting of frame made out of M.S tubes for top and bottom rails M.S frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame all as specified and directed.

Forming jambs, etc. to openings, (to foregoing items) including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work, complete with cement mortar 1:4 all as specified and directed.

Aluminium handles, fabricated, anodised of size 150 mm long complete all as specified and directed.

Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) of 250 mm long and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Butt hinge, 100 mm long medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

Floor door stopper of aluminium alloy body 150mm and tongue, anodised with hard drawn steel spring fixed in floor all as specified and directed.

Floor door stopper, with 150 mm long cover plate, of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor and including fixed in repairs all as specified and as directed.

150 mm long Aluminium anodised, barrel tower bolts of extruded section and fixed in repairs complete all as specified and directed.

Chequered cement concrete coloured tiles 30 cm x 30 cm x20-22 mm thick, with grey cement and pigments, set, jointed and pointed in neat cement slurry in floors, steps etc over and including 20 mm thick screed bed in CM 1 :4 complete all as specified and as directed.

75mm thick PCC (1:4:8) type D2 using 40mm graded stone aggregate as in sub base floor and finished even and fair complete all as specified and directed.

75mm thick plain Cement concrete, 1:3:6, type C-1 using 20 mm graded stone aggregate as in plinth protection and hard standing finish even and fair complete all as specified and directed.

Demolition of cement concrete reinforced in ground floor and paving not exceeding 15cm thick (below or above ground level) complete all as specified and directed.

Reinforced cement concrete (nominal mix) 1:2:4 type B-1 using 20 mm graded stone aggregate as in slab supported on wall, beam and column in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and similar work complete all as specified and directed.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. Fair finished surfaces of concrete flat complete all as speicified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed.

Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in cement mortar 1:6 complete all as specified and directed. Note :- Reinforcement shall be measured and paid separately.

Mild steel hold fast conforming to Fe-290 Gde-165 all as specified and directed.

Dismantling PVC water tank exceeding 250 ltrs and not exceeding 500 Ltr capacity from existing position and removing to stores all as specified and as directed.

Rotational moulded polyethylene water storage tank of capacity 1000 Ltr (cylindrical vertical with closed top) three layers, hoisted and fixed in position with proper inlet and outlet connections all as specified and as directed.

Demolition of reinforced cement concrete in any description and in any position all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exceeding 10 Sq m on plan and not exceeding 1.5 m in depth and getting out in hard/ dense soil complete all as specified and directed.

Ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe and fixed in repairs of size 20mm dia (Minimum weight 25mm-455gms) complete all as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for such as RCC post, manholes, landings etc (reinforcement to be cut as required to facilitate demolition and removing debris to distance not exceeding 50m all as specified and directed.

Dismantling fencing wire mesh any type all as specified and directed.

Supply only Chain link MS galvanised fencing, wire mesh any size (or) type of 3mm to 4mm dia wire complete all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick each, layer complete all as specified and directed

Removing excavated soil/ material to a distance exceeeding 250m and not exceeding 500m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete) set in cement mortor for 150 mm internal dia of pipe complete all as specified and directed

Concrete bed to drain pipes including packing under and haunching against the sides of the pipes after they are laid and tested in cement concrete 1:4:8 type D-2 using 40mm graded aggregate for 150mm bore pipe all as specified and directed.

Salt Glazed stoneware drain pipes of 150mm internal dia, grade 'A' laid in trenches and jointed in cement mortar 1:1 mixed with spun yarn and testing complete all as specified and directed

PCC 1:2:4, type B-1 using 20 mm graded stone aggregate as in coping, benching, bed block, lintel band, plinth courses, etc and similar work including necessary form work and weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Cutting into existing manholes for connecting new drains of 150mm internal dia, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and directed.

Plain Cement concrete type C-1, 1:3:6 using 20mm graded stone aggregate as in bottom of drains/ filling of gaps between drain and road, and as bed block for hold fast and the like of any description over 10mm in width or grith not otherwise described all as specified and directed.

Taking down complete of existing water proofing treatment of any description over roof slabs / parapets etc complete all as specified and directed.

Providing Plain cement concrete 1:2:4 type B0 using 12.5mm graded stone aggregate average thickness 50mm as in levelling / padding course on roof slab, projections on similar surfaces existing with slope making the surface even and smooth without using extra cement all as specified and directed.

Rendering 10mm thick fair faces of brick work or concrete surface in cement mortar 1:3 laid over the RCC roof slab, parapet wall when the concrete is green at any height and making the surface fair and even without using extra cement including using liquid integral water proofing compound as per manufacturer's instructions all as specified and directed. Note: Water proofing compound will be measured and paid separately.

APP modified prefabricated polymeric water proofing membrane mineral finish 4mm thick and weighing not less than 4.5 kg/sqm reinforced with non-woven polyester matt black finished weighing not less than 100 gm/sqm having softning point less than 140 degree celcius longitudinal tensile strength not less than 300N/sqcm, side lap 10cm with torch application of membrane over compatible primer at 0.40 Ltr/sqm and aluminium paint at 0.10 kg/sqm finished on top complete all as specified and directed. Note: The work shall be done by the authorised applicator as approved by the GE.

Plain cement concrete Type B1 1:2:4 using 20mm graded stone aggregate as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

Galvanised Iron pipe 15mm bore dia medium grade with all fittings fixed on wall, ceiling or laid in floors complete all as specified and directed.

Galvanised Iron pipe 20mm bore dia medium grade with all fittings fixed on wall, ceiling or laid in floors complete all as specified and directed.

Fixing only GI tubes 15mm bore medium grade with all fittings and laid in floor/ wall/ ceiling etc complete all as specified and directed. Note: GI Pipe obtained from from taking down shall be reused as directed.

Fixing only GI tubes 20mm bore medium grade with all fittings and laid in floor/ wall/ ceiling etc complete all as specified and directed. Note: GI Pipe obtained from from taking down shall be reused as directed.

Disconnecting existing PVC tanks of capacity exceeding 500 ltrs and not exceeding 1000 ltrs, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and refixing in position all as specified and directed.

Disconnecting existing PVC tanks of capacity exceeding 250 ltrs and not exceeding 500 ltrs, setting aside (or lowering if required) for repairs, cleaning etc and hoisting if required reconnecting and refixing in position all as specified and directed.

Dismantling of PVC water tanks of 1000 Ltr capacity from existing position all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling fencing wire mesh any type not exceeing 4 Kg per Sqm all as specified and directed.

Supply and fixing wire neting 1.40mm dia of mesh size 25mm complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:6 for laying floor finishes, complete all as specified and directed.

Taking down Shutter of any description exceeding. 1 sqm and not exceeding 2 sqm each all as specified and directed.

30mm thick glazed and skeleton, 2nd class hardwood shutter, divided into squares to receive glass, gauze (with sash bar) with plain chamfered or rounded, mitred and rebated sah bars, any numbers the size of member of shutter as specified in SSR Pt-I section 8 clause 8.24 (b) window and ventilaters shutters using second class hard wood and fitted to chowkat all as specified and as directed.

35 mm thick flush shutter,solid core construction, with block Board Core and plywood face panels covered with decorative Face Veneer with lipping/ frame on one faces, complete all as specified and as directed.

Preparation of surfaces of wood and tarring back of chowkat, area tarred exceeding 0.10 sqm but not exceeding 0.5 sqm each all as specified and as directed.

All as per item No.125 hereinbefore but treating small articles such as hold fast etc tarred area not exceeding 0.10 sqm each all as specified and as directed.

Aluminium anodised, barrel tower bolts of extruded section 150 mm long all as specified and directed.

Extruded aluminium alloy handles 100 mm size, fabricated type, anodised complete all as specified and as directed

Extruded aluminium alloy handles 150 mm size, fabricated type, anodised complete all as specified and as directed

PCC 1:5:10 type - E2 as in mass concrete in sunken floors using 40mm graded stone aggregate complete all as specified and as directed.

PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors with pressure rating 6 Kgf/sq cm including fixed in repairs all as specified and as directed.

PVC (SWR) pipes 110 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors with pressure rating 6 Kgf/sq cm including fixed in repairs all as specified and as directed.

PVC (SWR) pipes 160 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors with pressure rating 6 Kgf/sq cm including fixed in repairs all as specified and as directed.

PVC (SWR) bend of any radius 75 mm dia complete all as specified and as directed.

PVC (SWR) bend of any radius 110 mm dia with access door complete all as specified and as directed.

PVC (SWR) bend of any radius 160 mm dia with access door complete all as specified and as directed.

Applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.2 Kg per sqm including cleaning the surface and APP based polymeric membrane weighing minimum 3Kg/sqm and minimum 300 thick reinforced with polyster non wove fabric (weight not less than 150 gms/sqm) laid on primed surface by forced application complete all as specified and as directed.

Coloured Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement mixed with pigment to match the surface over and including 15mm thick screed bed or bedding layer of mortar in cement mortar 1:4 including spacers with epoxy grouting complete all as specified and as directed.

Vitreous china wash basin, white, flat back, size 550mm x 400mm including brackets, cutting for and pinning in ends of brackets or erecting stand, with and including brass chromium plated perforated waste coupling / fittings 32mm dia with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed, PVC waste pipe of 32mm bore and of suitable length, 15mm bore pillar taps, cast copper alloy with capstan heads, chromium plated, fancy type screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly nuts, screwed for iron pipe and PVC connection 15mm size with PTMT nuts of length 450mm and fixed in repairs complete all as specified and directed.

Chroumium plated fancy type 2in1 bib tap fixed with existing pipe including fixed in repair all as speicified and as directed.

Stop valve cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type chromium plated ,15mm bore including fixed in repair all as specified and directed.

Stop valves, fancy type, chromium plated with long shank and cup concealed type, chromium plated cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed in repair all as specified and directed

Preparation of old plastered surfaces of walls including washing rubbing down and stopping of distempered and painted and applying one coat of distemper oil emulsion washable on old surfaces on walls including filling and making surface smooth and making good chipped off surfaces as required complete all as specified and as directed.

Complete removal of existing treatment of wall surfaces and applying two coats of Oil Bound Distemper washable over a coat of primer, over wall care putty in two layers including sanding and preparation of surfaces to a true, even and smooth complete all as specified and directed. Note :- Putty will be measured and paid separately.

Wall care putty on wall average thickness 2-3mm in one coat of wall care putty in two layers complete all specified and directed.

Preparation/ Removal of old treatment on plastered / stone / brick wall surfaces and applying two coats of Exterior Emulsion Paint (Anti Fungal) white or tinted complete all as specified and as directed. Note: 1. Rates shall be quoted inclusive of required scafolding for a height upto 10 meters buildings.

Plain cement concrete Type B0 1:2:4 using 12.50mm graded stone aggregate in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

Dismantling of Wrought Iron or Mild steel work of any description not otherwise provided for complete all as specified and directed.

Mild steel works in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle) including distance pieces, cleats etc.of grade Fe-410-W (Gde-E-250) quality-A all as specified and directed.

Brick work with sub class ‘B’ bricks, (old size) straight or curved on plan exceeding 6 mtr mean radius built in cement mortar (1:6) for all as specified and directed.

Rendering 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 finished even and smooth without using extra cement complete all as specified and directed.

Preparation of newly treated surfaces of walls and applying two coats of oil bound distemper over a coat of primer complete all as specified and as directed.

Supply and fix in repairs Powder coated aluminium door, window, ventilator frame with side hunf including bombay sliding aluminum sections sliding window where required or pull and push type in frames and shutters with two track sliding aluminium frame and in partitions, Make : Jindal or equivalent of approved size incluidng necessary joining cleats, glazing clips, rubber packing anodised aluminium snap beading, screws, including necessary anodised aluminium fittings like handles, locking arrangements etc., complete all as specified and as directed and as per manufacturer's instructions.

75mm thick PCC type B-1, (1:2:4) using 20mm graded stone aggregate as in flooring, Tank Staging including necessary formwork complete fair finished even and smooth without using extra cement,complete all as specified and directed.

Cutting and tapping of existing 40mm pipe and inserting a Tee for new connection of size 20mm including reducers requred if any complete all as specified and directed.

Supply and lay pipe galvanized "Medium class" including fittings of size 20mm (3/4") dia all as specified and directed.

Supply and lay pipe galvanized "Medium class" including fittings of size 25mm dia all as specified and directed.

Gunmetal globe or gate valve 20mm with iron wheel head screwed both ends for iron pipe of size 40mm dia all as specified and directed.

Gunmetal globe or gate valve 20mm with iron wheel head screwed both ends for iron pipe of size 20mm dia all as specified and directed.

Ball brass valves high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed of dia 20mm all as specified and directed.

Excavation in trenches not exceeding 1.5M wide and not exceeding 1.5M in depth and getting out in hard/ dense soil for laying of GI / DI pipe complete all as specified and directed.

Removing excavated soil/ material to a distance not exceeding 50m and depositing where directed at a level not exceeding 1.5m above the starting point all as specified and directed.

Taking down aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting, bell etc, and making good disturbed surfaces with smooth finish matching with the existing surface of walls, floors, etc. and with existing colour all as specified and directed.

Point wiring complete with 1.5 sqmm (nominal area) FRLS grade PVC insulated, unsheathed stranded copper conductor single core cable 1100 volts grade in and including PVC concealed / surface conduit medium grade complete with conduit fittings/accessories with provn of 1.2 mm thick MS terminal boxes of suitable size and 3 mm thick plastic laminated sheet top cover for housing of switches, sockets etc including 1.5 sqmm FRLS grade PVC insulated unsheathed stranded copper conductor cable for earth continuity conductor and connected to common earth dolly for One light/ Ex-fan point controlled switch all as specified and directed. Note: Cutting chasing of wall / floor will be measured and paid separately.

All as per Item No 164 hereinbefore but One 2 pin /3 pin 5 Amps socket out let multipurpose on independent Board all as specified and directed.

All as per Item No 166 hereinbefore but point wiring complete with 2.5 sqmm for 3 pin 15 A socket outlet on independent board including 2.5 sqmm FRLS grade PVC insulated unsheathed stranded copper conductor cable for earth continuity conductor all as specified and directed.

Modular switch one way 6A 230V AC 50 HZ SP one module all as specified and directed.

Modular switch one way 16A 230V AC 50 HZ SP one module all as specified and directed.

Modular socket 2/3 pin combined 6A 230V AC 50 HZ SP two module all as specified and directed.

Modular socket 6A/16A 2/3 pin combined 230V AC 50 HZ SP two module all as specified and directed.

Terminal box suitable for one/ two modular plate of size 75x75x50mm including cutting, grooving and plastering etc. all as specified and directed.

Taking down old terminal box and supply and fix Terminal box suitable for three modular plate of size 100x75x50mm including cutting, grooving and plastering etc. all as specified and directed.

Taking down old terminal box and supply and fix Terminal box suitable for Four modular plate of size 128x75x50mm including cutting, grooving and plastering etc. all as specified and directed.

Taking down old terminal box and supply and fix Terminal box suitable for Six modular plate of size 210x75x50mm including cutting, grooving and plastering etc. all as specified and directed.

Frame plate with matching cover, two module plate all as specified and directed

Frame plate with matching cover, three module plate all as specified and directed.

Frame plate with matching cover, four module plate all as specified and directed.

Frame plate with matching cover, six module plate all as specified and directed.

Ceiling rose, 3 terminals PVC / polycarbonate, isolated body all as specified and directed

20 W LED batten in extruded aluminium housing with diffuser complete all as specified and directed.

LED luminaire 600mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size all as specified and directed.

Gate light aluminium die cast with modern artistic design and white PC diffuser suitable for retrofit LED lamps all as specified and directed. Make: Havells: Cat No LHFOAQE1NZ5K7X5 or equivalent in surya, Panasonic, Phillips etc.

Decorative wall light, gold finish fixture with white glass diffuser including 7 W LED lamp E27 base warm white colour all as specified and directed. Make: Havells Cat No LHFOAKD2TZ1D060 or equivalent in Panasonic, Surya

LED light fittings 1 x 9W / 1 x 10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size all as specified and directed.

LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

LED security light fittings of 25 Watt comprising of epoxy powder coated housing enclosed with glass cover in frame with protection IP 65 complete with all accessories and lamp colour white and fixing in and including GI bracket of suitable size / dia all as specified and directed.

Cutting chases in stone masonry wall/concrete floor/roof for laying PVC conduit and making good to facings where required and pointing in cement mortar 1:3, and making good, cutting not exc 10cm girth all as specified and directed

Exhaust fan, steel body AC single phase 230V of size 300m sweep with blades and frame and louvers complete all as specified and directed.

Taking down old unservicable RCCB, MCB, MCB DB of any size/ type/ ways complete and and removing material to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good matching with the existing colour to the disturbed surfaces of walls, floors etc all as specified and directed.

MCB DB TPN 4 way 415 volts, double door type with minimum capacity of 200 Amps rated bus bar including necessary dummy plate in concealed including any alteration required shall be made (cutting brick/ stone wall) and necessary civil works all as specified and directed.

MCB DB SPN 8 way 230 volts, double door type with minimum capacity of 200 Amps rated bus bar including necessary dummy plate in concealed including any alteration required shall be made (cutting brick/ stone wall) and necessary civil works all as specified and directed.

MCB SP 6-32 Amps, 230 volts capacity complete all as specified and directed.

MCB SPN 32 Amps, 230 volts capacity complete all as specified and directed.

MCB TPN 415V 63 Amps capacity all as specified and directed.

Taking down Submain wiring with aluminium conductor along with PVC Conduit and Material and Labour for Submain wiring with 2 runs of FRLS grade PVC copper conductor cable 6 sqmm, multistranded along with FRLS grade PVC insulated copper earth continuity conductor 6 Sqmm drawn through and including PVC Conduit pipe 20 mm dia with all fittings all as specified and directed. Note: 3 Runs of cable and one run of conduit shall be measured as one RM

Earthing complete with galvanized steel earth plate electrode 60 cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 mtrs deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level, connected to galvanized earth wire of size 4mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel all as shown in electrical platee No 3 connected to earth testing point including necessary excavation, earth work, PCC pit ,RCC cover 1:2:4 B1 with 8 mm dia MS bars at 100 c/c, funnel, watering pipe etc. all as specified and directed including testing on completion.

Stationary Storage type (Vertical type) energy efficient electric water heater of capacity 25 Ltr complete with 04 Nos grouting bolts, nuts & washers, grouted on stone wall and making good disturbed grouted surface, thermoplstic body, neon indicator, safety valve etc including connecting pipes complete all as specified and directed. Note: Removed Geyser to be handed over to MES store for safe custody of the items.

GMS Builders

CRD TRADERS

AR Mohamed Yakub and Co

P K ENTERPRISES