8788/GWL/E8 SPECIAL REPAIR TO BLDG NO P-106/01 TO 04 JCO MD ACCN INCL CERTAIN MINOR AND REV WORKS AT MORAR CANTT UNDER GE GWALIOR

Amount

Taking down chowkhat or frame (without taking off shutter from the frame) not exceeding 1.5 Square Metre each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed.

Taking down chowkhat or frame (without taking off shutter from the frame) exceeding 1.5 sqm and not exc 4.00 sqm each , removing from the site Cutting holes exc 150 Sq.cm but n.exc 400 Sq.cm in super facia area into or through brick walls built in mud mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed.

S&F solid PVC door frame of size 50mm×47 mm made out of 5 mm pre laminated colour PVC sheet reinforced with MS square tube supplying and fixing in opening as per specifications and drawings.

S&F MS Pressed steel frames for doors with one or more redates including necessary fixing lugs hinges lock strike plate etc complete as specified abd size of frame 105x60mm complete. Note : cost of filling of PCC (1:3:6) type C-0 in hollow portion of frame shall be measured in appropiate item of BOQ .

S&F MS Pressed steel frames for doors with one or more redates including necessary fixing lugs hinges lock strike plate etc complete as specified abd size of frame 125x60mm complete. Note : cost of filling of PCC (1:3:6) type C-0 in hollow portion of frame shall be measured in appropiate item of BOQ .

M&L for PCC 1:3:6 type C0 (12.5mm stone agrregate) for filling in pressed steel frames and like complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top and bottom rails M.S frame shall be covered with heat moulded pre lam colour PVC 'C' channel having a PVC shut strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail& bottom rail, panelling of pre lamanited colour PVC sheet to be fitted in MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement.

M & L for factory made 35 mm 2nd class Hard Wood, plain framed factory made panelled shutters ( two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board medium density, wood particle board with commercial veneering on both face IS 1003 ( Part-I) kiln seasoned and chemically pressured treated complete all as specified and directed.

M & L for 35 mm thick glazed and skeleton factory made shutters of 2nd class Hard Wood, open rebated and prepare to reveive glass, guage etc (without sash bars ) edges of framing plain chamfered or rounded, fitted with moulded beads both sides for securing glass etc, size of members of shutters as specified complete all as specified and directed.

M&L preperation of new wooden surface and applying two coat of synthetic enamel paint over a coat of pink primer on new wooden surface any description not otherwise described over 10 cm width or girth and complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium frame for doors , windows , ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed.

M & L for Powder coated (minimum thickness of powder coating 50 micron) aluminium window and ventilator (adequate track(sliding oenable)) without sash, aluminium section weighing 0.55 kg/m including joining cleats, glazing clips, rubber neoprene packing, necessary powder coated hardware ie. handles, barrel tower bolts, hinges etc, powder coated aluminum snap beading, screws etc. complete all as specified and directed Note : Panel filling ie. glass, fibre sheet, board, wire mesh etc. shall be measured and paid for separately.

S&F galvanised wire cloth, .36mm nominal dia of wire and average width of aperture 1.18mm and fixed with tinned tacks or galvanised staples complete all as specified and directed

Dismantling boarding any description fixed with nails in any position (including cup board shutter/shelve upto 25mm thick) complete.

S&F for 18 mm thick PVC Celuka ply of one side prelaminated and other side plain white colour fixed with screws ,solvent /adehesive complete all as specified .

S&F Aluminium anodised barrel tower bolt of 200mm of extruded section complete

S&F Aluminium anodised barrel tower bolt of 150mm of extruded section complete

S&F for Haps and staple safety type Aluminium anodised with MS hinge pin including bolt to hinge pin of 100 mm size sixed with screw complete all as specified .

S & F Magnate catcher of metal body and striking plate heavy duty includind fixed with screw complete.

S&F continuous (piano) hinges, mild steel, bright finish or electrogalvenised of not exc 25 mm flaps complete.

S&F Aluminium alloy anodised sliding door bolt of 250mm with haps, staple ( bolt type ) & fixing clips of sheet etc.

S&F MS Sliding door bolts Rod pattern stove enamelled black with bolts not less than 12mm dia with and including a minimum of 6 bolt and nuts four on bolt plate and two on staple plate of 250mm size complete.

S&F Aluminium butt hinges of 100mm size type C-22 complete.

S&F MS 150 mm ordinary rat tail springs plate type incl.rollar plate etc.

S&F Extruded aluminium alloy handle of 125mm size fabricated type, anodised.

Demolition of cement concrete of any description and in any position (unreinforced) in ground floors and paving not exceeding 15 cm thick (below or above GL) complete all as specified and directed.

Demolition of cement concrete of any description and in any position reinforced concrete (re-inforcement cut to facilitate demolition) including disposal of unserviceable of mateial complete all as specified and directed. Note:Demolition material throughout MOD Land rate include above item

Taking down existing tarfelt from roof and removing from site all as directed.

M&L for 10 mm thick rendering in CM (1:4) over roof ,surface finished even and rough mixed with water proofing compond complete all as speceified and as directed by engineer- in charge . Note : Water proofing compound shall be measured and paid separately under appropriate item of BOQ as "supply only "

Supply only Liquid water proofing compound complete.

M &L For applying water proofing treatment with the following coats :- (a) First coat of bitumen primer conforming to IS -3384 @ 0.4 Kg/sqm (b) Second Layer of APP based polymectric membrane minimum weighing 3kg /sqm and minimum 3 mm thick reinforced with polyster non woven fabric (wt. not less than 150 gms /sqm ) laid on primed surface by torch application complete all as specified and as directed by engineer in charge.

M & L for cutting grooves in brick wall/ RCC, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete.

M & L PCC (1:2:4) Type Bo using 12.5 mm graded stone agg as levelling course/mass concrete complete all as spd and directed.

M&L, precast cement concrete tiles of size 250mm x 250mm x 20 mm as in foor top ,confirming to IS-1237-1980 laid over 15 mm thick screed bed in CM 1:4 and set, jointed and pointed in neat cement slurry in floors, and cut & plished between tiles 2 to 3 mm will be filled with cement mortar (1:2) by mixing of chemical or equilant approved by the GE etc complete all as specified and as directed.

Dismantiling of stone slabs and tiles (Kota stone etc.) of any discription or any thickness in floors, aprons, skirting, dado, pcc tiles at roof etc. laid bedded and pointed in any mortar complete all as specified and directed.

Dismantling floor, hearth or wall tiling of any description and in any position including cement mortar bedding (but not backing) complete all as specified and directed.

M&L 75mm thick PCC (1:3:6) Type C2 using 40mm graded stone agg as in plinth protection/Path etc surface even and smooth without using extra cement complete all as specified and as diected by engineer in charge.

M&L 25 mm thick cement concrete (1:2:4) type B-0 (12.5 mm graded stone aggregate) as in floors,finish rough to receive th\e floor finishes etc

M&L Granite slab 16 mm to 18 mm thick machine cut, bedded and joined with cement and pointed with white cement with admixture of pigment to match over and including 20 mm thick screed bed CM (1:3) .the shade of granite stone including cutting and polishing type as in cill and jamb/skirting, steps cooking plateforms includigng rounding off the exposed edges and polishing all as specified and directed..

M&L for machine cut Kota stone slab 18mm to 20 mm thick , as in flooring , laid over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing , over and including screed bed or bedding layer of mortar 20 mm thick in cement mortar (1:3 ) complete all as specified and directed.

M&L for machine cut kota stone slab 18mm -20 mm thick as in riser / steps, skirting, dado,cills and pillars laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing over and including 10 mm thick backing coat in CM (1:3) complete all as specified and directed.

M&L for digital glazed ceramic tiles, coloured tiles 300mm x 450mm x 7mm thick on vertical faces ie. as in skirting/dado etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles fix over and including 10 mm thick backing coat in cement mortar (1:3) complete all as specified and directed.

M&L for non skid ceramic Coloured tiles, 300mmx300mmx 6 mm to 7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match with the colour of tiles, over and including 15 mm thick screed bed or bedding layer of cement mortar( 1:6) complete all as specified and directed.

M&L for vitrified ,coloured and printed tiles of 8 to 10 mm thick (Square / Rectangular ) polished area of each tiles not exceeding 0.36 Sqm as in flooring over and including 15 mm thick cement screed in (1:6 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

M&L for vitrified ,coloured and printed tiles of width as directed and 8 to 9 mm thick as in skirting fixed over and including 10 mm thick cement screed in (1:4 ) CM set and jointed in neat cement slurry and pointed in white or coloured cement to match with the colour of tiles complete all as specified and directed.

Taking down cement or cement lime plaster on brick or stone walls etc. including racking out joints hacking for key scrubbing down with water etc.complete.

M&L for 15 mm thick rendering in cement mortar on fair faces of brick work or concrete surfaces , applied in two layers ie. Ist layer of 10 mm thick rendering in cement mortar (1:6 ) and 2nd ( top ) layer of 5 mm thick rendering in cement mortar (1:4 ) and top layer mixed with water proofing compound as per manufacturer's instruction & finished even and smooth without using extra cement complete all as specified and directed. Note:- Water proofing compound shall be measured and paid seperately under appropriate item of Sch 'A' as "supply only")

M&L for 10 mm thick rendering in cement mortar (1:6) on brick or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

Supply only Integral water proofing compound complete.

M&L for rendering 5 mm thick in Cement Mortar (1:3) on ceiling finished even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of newly plastered sufaces of walls & applyintwo coat of premium acrylic exterior anti algal fungal emulsion paint over one coat of weather coat exterier primer on wall all as direced by Engr-in-Charge.

M&L for preparation of the newly plastered surfaces of walls & applying three coats of white wash on wall surfaces complete all as specified and directed.

M&L for preparation of the newly plastered surfaces of ceiling & applying 3 coats of white wash on ceiling surfaces complete all as specified and directed.

M & L two coat of oil emulsion distemper over a coat of Birla wall care putty on plastered surfaces on wall incl. preparation of surfaces etc.

M&L applying for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces over 10 cm width or girth including preparation of new surfaces.

Complete removal of existing treatment on wall (any number of layers ) by scarping with steel scapers or any other mean including filling depessions of scapped surface with putty and pereparation of surface for further treatment and M&L for two coats of distemper oil emlusion white or tinted over a one coat of wall care putty on walls complete all as specified and dircted by Engr-in -Charge

Preparation of old decorated surface of wall and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and applying two coat of white wash complete all as specified and directed.by Engr-in-Charge

Preparation of old decorated surface of ceiling and including cornices plastered or unplastered surfaces by brooming down or steel wire brushing to remove all loose scales, and foreign materials scarping down , smoke soot moulds , moss and efflorescent salts treating oil and greasy spots and applying two coat of white wash complete all as specified and directed.by Engr-in-Charge

Demolition of brickwork or stone/ boulders masonry built in cement mortar or cement lime mortar incl all quoins, arches, pillars etc. but not excluding ashlar facing dressed stone work and precast concrete articles.

Excavation in trenches nexc 1.5m wide and nexc 1.5m in depth as in foundation etc as in soft loose soil complete.

Excavating in trenches exceeding 1.5M in depth and not exceeding 3 mtr in depth getting out for sump & laying of pipe etc in soft/loose soil.

Returning, filling of excavated soil, including spreading leveling, watering and well ramming in layers, not exceeding 25cm complete all as specified and directed.

M&L Brick work with sub class B bricks straight or curved on plan exc. 6m mean radius built in cement mortar (1:6).

Reinforced cement concrete (normal mix) type B-1 1:2:4 (20mm graded aggregates) as in shelves etc complete all as specified and directed.

M&L for mild steel TMT bars ,6 mm to 8 mm dia over, cut to length bent to shape required including cranking bending spirally for hoping for coloumns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

Providing precast concrete as in cover slab, lintel etc using RCC (1:2:4) with 20mm graded stone agg including all form mould etc complete.

Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 20mm bore of pipe.

Taking up or down steel tubing and connetion including cleaning for refixing or removing to store of 25mm bore of pipe.

supply and laying 20 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall ,ceiling or laid in floors complete all as specified and as directed by engineer in charge .

supply and laying 25 mm dia .of bore CPVC pipe SDR11 and Plain CPVC SDR11 fittings (ISI ) marked ,concealed or fixed to wall ,ceiling or laid in floors complete all as specified and as directed by engineer in charge .

S&F in repairs 110mm dia PVC(SWR) type B pipes single socketed, in any length with rubber ring joints,fixed to walls complete all as specified and as directed by engineer in charge .

S&F 75 in repairs mm dia PVC(SWR) type B pipes single socketed, in any length with rubber ring joints,fixed in Wall/laid in floor complete all as specified and as directed by engineer in charge .

S&F 110mm dia PVC(SWR)pipes bends any radious with acces door complete omplete all as specified and as directed by engineer in charge .

S&F 75 mm dia PVC(SWR)pipes bends any radious.with acces door complete all as specified and as directed by engineer in charge .

S&F 110mm dia PVC(SWR)pipes junction,single (single T/Y ) equal or unequal any radious.with acces door complete all as specified and as directed by engineer in charge .

S&F 110mm dia PVC(SWR) vent cowl complete all as specified and as directed by engineer in charge .

M & L 75 mm dia of out let PVC (SWR) floor trap plain with cp grating incl. jointing with solvent cement as in repair complete all as specified and as directed by engineer in charge .

M & L PVC (SWR) gully trap 125 /100 plain with grating incl. jointing with solvent cement as in repair complete all as specified and as directed by engineer in charge .

S&F for in repair PVC valveless syphonic action type flushing cistern low level white with inlet ball valve,float end handle handle including bracket complete of capacity 10 litres, complete all as specified and directed.

S&F for in repairs 15mm angle cock ISI Mark chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed and complete all as specified .

S&F for in repairs for 15 mm Stop valve cast copper alloy screwed down high pressure with CAPSTON HEAD handle chromium plated with long shank and cup (concealed type) screwed both ends for iron pipe 15mm bore or for unions complete all as specified and directed.

S&F for 15mm ,bib tap ISI Mark Fancy type long body chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe fixed in repair and complete all as specified

S&F for in repairs15mm,pillar taps ISI Mark Fancy type long body chromium plated,cast copper alloy, with brass ceramic disc spindle and capston heads,scewed down high pressure, with or without lettered 'hot' or Cold' with long srewed shanks and flynuts, srewed for iron pipe complete all as specified .

S&F for shower rose brass chromium plated without swivel joints, 100 mm in size including fixing to steel pipe complete all as specified and directed fixed in repairs, complete all as specified and directed.

M&L vitreous china squatting pan, orissa pattern sise 580x440mm white with integral foot rest (excluding flushing cistern) including vitreous china ‘P’ or ‘S’ traps connection to trap and to flushing pipe to complete fixed in repairs and making good to floor complete.

S&F of vitreous china wash basin, white, flat back, size 550 x 400mm Including waste coupling ,waste pipe and labour for fixing pillar tap ,pvc connection but including cutting for and pinning in ends of and including brackets complete all as specified and directed. Note : Pillar tap and PVC connection will be measured paid as supply only.

Supply only 15mm dia PVC connection with PTMT nuts of length 450 mm.

S&f corner glass shelf 300mm ( with ABS Bracket ) complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass 12 cm wide with CP bracket guard and railing 60 cm long complete.Prayag Cat BEA-49 or similar in other make

S&F Soap dish of CP fixed with pvc rawl plugs and screw complete.

S&F in repair CP tubular towel rail D type 20mm dia and 60cm long complete all as specified and directed.

S & F Peg set of six S.S. fixed to wall with PVC plugs and screw complete.

S & F in repair Curtain rail stainless steel decorative type 25 mm dia including fixing bracket and end knobs complete specified and diected by engineer in charge.

Dismantling water tanks of any description and in any position , of capacity exceeding 500 litres but not exceeding 1000 litres complete all as specified and directed.

S & F Rotational moulded poly-ethylene multilayer water storage tanks (cylinderical vertical with closed top) 1000 litres capacity, triplr layer in construction white in colour hoisted and fixed in position complete all as specified and directed.

S&F for 20mm ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 m m - 210 gms / 25mm-455gms/ 40mm - 690 gms) complete all as specified and directed.

S & F in repair gun metal globe / gate value with iron wheel head screwed both ends for iron pipe of 20mm bore all as specified.

S & F in repair for plate rack made out of stainless steel of wire type / sheet pattern size nad type as directed by Engineer In Charge and approved by GE fixed to wall with necessary fitting arrangement Complete all as specified and directed.

S&F in repair sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plug washer and waste coupling, waste pipe including bedding in CM to dwarf wall or including fixing cantilever brackets and connections to pipe over all size 915mmx460mm built size 410mmx330x160mm complete.

Surface excavation n.exc. 30 cm deep and av. 15 cm deep and getting out in any type of soil complete

M&L for PCC Type D2 (1:4:8) using 40mm graded stone agg as in foundation filling mass concrete, complete all as specified and directed.

M&L for sand filling under floors or in foundations including watering and consolidation complete all as specified and directed .

Material and labour for machine made ,1st quality, precast cement concrete rubber moulded coloured interlocking paver blocks / tiles , 60 mm thick of grade M-35, of any shape or shap and designe as approved, with grey cement and pigment , laid over fixed as in floors/ paths/ pavings etc, complete all as specified and directed.

M&L for 15 mm thick dubbing coat in Cement Mortar (1:4) on ceiling surface complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue ,anodised with hard drawn steel spring,150mm long, fixed in floor .

M&L for preparation surfaces for building Nos and applying one coat of synthetic enamel paint and writing letters or figures (Block, Roman, Italic or Indian) of n exc 10cm height, width of letter shall not be less than 15mm, including stops, commas, lines, brackets and making outer boarder with approved tint of synthetic enamel thick paint complete all as specified and as directed.

S&F rolled section as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to Fe-290 ( Gde E-165) complete all as specified and directed

S&F Pre painted galvalum sheet 0.50 mm thick having aluminum zinc coating 150 gsm/ sqm trapezoidal profile steel sheet any colour having tensile strength of 550 Mpa as in Roof covering /cladding to wall fixed with self tapping screws complete all as directed by Engineer -in -charge.

Dismantling of AC (corrugated / semi-corrugated) sheets in roof covering including any type of ridges complete all as specified and as directed.

Excavating in posts holes (or similar holes) in hard/dense soil each n.exc 0.50 cu.m getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n.exc 25cm watering, and removing surplus soil to a distance n.exc 50m and making good surface complete all as directed by Engineer -in -charge.

M/L for providing PCC 1:3:6 type C2 using (40mm graded stone aggregate) in foundation filling and mass concrete complete all as directed by Engineer -in -charge.

M&L Hand rails, half round or other stock section or core for wooden hand rail straight portion , drilled and counter sunk for balusters running bars, for doors, balusters, nosing to steps including embedding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing post including cutting tops to shape as directed, drilling holes, notching for wire , etc.; flat iron fillets ( for securing wire mesh etc. including all necessary drilling , bolting or rivetting , etc., and similar work conforming to Fe 290 Gde E 165 with and including applying two coats of synthetic enamel paint over a coat of primer alround before fixing in position complete all as specified and directed

Supply only, chain link fencing of MS galvanized fencing, any size or type complete all as directed by Engineer -in -charge.

Fixing only chain link fencing including line wires, any mesh , size and type fixed to any type of standards, rails, straining bolts, etc., incliding provision of binding wire complete all as specified and directed Note : Supply only chain link fencing and line wire will be measeured and paid separetly.

S&F mild steel round bars 10mm dia and over cut to length bent to shape required including cranking, bending, spirally for hooking ends stiffeners confirming to Fe 290 (Gde E-165) complete all as directed by Engineer -in -charge.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed to other, or screwed both ends, each screwed end to be fitted with washers and hexagonal or square nut length of bolt exc 5cm but n.exc 10cm long and dia of neck 11 to 15mm complete all as directed by Engineer -in -charge.

M&L applying for two coats of synthetic enamel paint over a coat of red oxide primer on new steel surfaces over 10 cm width or girth including preparation of new surfaces.

S&F Framed brackets of angles or tees with web and flanges cut to shape, drilled and counter shunk for screw, including bending and welding angle necessary gusset plate riveting etc n exc. 10 kg each brackets confirming to Fe-290 Gde E-165 complete all as specified and directed.

Excavation over area as in soft / loose soil nexc 1.5 m deep and getting out complete all as specified and as directed.

M&L moorum/ red bajri filling in floors or pavings laid in layers n. exc 15 cm thick, spread, levelled and rammed including watering complete all as specified and as directed.

Removing excavated material nexc 50m and depositing where directed at a level nexc 1.5Km above the starting point with soil complete.

Taking down carefully existing aluminum / copper point wiring (light, fan, socket or power point) complete of any description including fitting such as switches, ceiling roses, pendants, tube light fitting, ceiling fan with regulators, sockets, wooden boards, laminated sheets from sunken boxes, boards, shades light fitting etc and making good the disturbed surfaces of walls, floors, ceiling etc to match with existing surfaces complete all as specified and directed.

Taking down ceiling fan of any sweep,removing blades, cleaning the fan completely of dust and dirt and Re-hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook rubber pad, nut bolts and washers etc, complete all as specified and as directed by Engr-in-charge.

Taking down submain wiring of any size any type and in any position metalic/non metallic PVC conduit of wooden batten complete all as specified and directed.

Taking down unserviceable Sheet metal box & MCB DB SPN with MCB's of any make/capacity, complete, all as specified and directed by Engr-In-Charge.

Taking down unserviceable TPN DB with MCB's of any make/capacity, complete, all as specified and directed by Engr-In-Charge.

M&L, concealed point wiring with PVC insulated and unsheathed electric cable 1100 volts grade single core FRLSH confirming to IS 694:2010 having multi stranded copper conductor of 1.5 Sqmm nominal cross sectional area (ISI marked with valid CML No) drawn in and including concealed non metallic rigid PVC conduit medium grade( ISI marked with valid CML No) not less than 20 mm dia confirming to IS 14930 (Part-I) 2001, with all fitting and fixing accessories and 1.5 Sqmm FRLSH PVC insulated unsheathed multistranded copper conductor cable as continuous earth conductor, connected to common earth dolly by providing suitable lugs with & including pressed steel sunken terminal boxes factory made for mounting switch, regulators etc with and including 2.8 mm thick plastic laminated sheet cover (white) ISI marked, fixed with brass screws and cup washers duly painted with two coats of anti corrosive paint/black bituminous paint outside and two coats of aluminium paint inside for mounting switches. sockets etc complete for the following:-

One light point controlled by one switch.

One Ceiling fan point controlled by one switch.

One Exhaust fan point controlled by one switch.

One Bell/Buzzer point controlled by one way 5 Amp push button switch.

One 5 pin multipurpose socket out let 5/6 Amps on the same board with other switch.

One 3 pin/5 pin switch socket outlet, 5 Amps on independent board.

For one light point controlled by 2- two way switch

All as per item No 130 here in before but point wiring with 2.5 sqmm FRLSH confirming to IS 694:2010, multistrand copper conductor cable for one six pin socket outlet 15 Amps controlled by one switch on independent board and 2.5 sqmm FRLSH PVC insulated multi strand copper conductor cable as continous earth wire.

S&F switch piano, flush button single pole one way 5 Amp complete all as specified and directed.

S&F socket out let, multipurpose, 2 in 1 5 pin, 5 Amp complete all as specified and directed.

S&F switch piano, flush button single pole one way 15 Amp complete all as specified and directed.

S&F socket out let multipurpose flush type, 2 in 1 6 Pin 5/15 amps complete all as specified and directed.

S&F switch piano, flush button single pole two way 5 Amp complete all as specified and directed.

S&F bell push flush type, 5 Amps complete all as specified and directed.

S&F of buzzer Ding Dong, AC, 230 Volts, single pole complete all as specified and directed.

S&F ceiling rose surface bakelite 63.5 mm dia three terminal complete all as specified and directed.

S&F Lamp holder with metal ring, PVC/Polycarbonate type with back plate suitable for batten fittings non ISI Marked complete.

S&F electronic step rotary type fan regulator of two module capacity 80 to 100 Watt, 240 volts, AC 50Hz complete all as specified and directed.

S&F LED 'T' Type Mirror light fitting 09/10 watt with provision of fixed in Lamp holder complete.

S&F Decorative ultra slim LED Tubelight fitting of LED with extruded polycarbonate, enviormental friendly energy efficient ready to use, 20 watt, 6500K fitting, incluing reqd length of not less than 1.0 Sqmm PVC multistranded BIS marked 03/02 core copper conductor for electrical connection from ceiling rose to connector of LED fitting including testing on completion all as specified and directed.

S & F security light fittings better optics for uniform distribution IP 65 protection LED of 30 watt, Heat resistance glass, pressure die cast aluminium housing including 25mm dia galvanised iron pipe light grade bracket bent to shape over all length 0.60mtr fixed to wall with 02 Nos FI clamps made of 40 x 5 mm FI, 15 cm long, 8 mm dia bolts and nuts with washers grouted in wall complete including reqd length of 1.5 Sqmm PVC multistranded BIS marked, 03 core copper conductor for connection from ceiling rose to light fittings incl testing on completion all as specified and directed.

Supply & fix BEE 5 star rating energy efficient ceiling fans 1200 mm sweep with minimum air delivery 210 cum/min, down rod all accessories required including regd length of 3 core 1.0 sqmm PVC multistranded copper conductor, PVC connector for proper hanging of fan and testing complete all as specified and directed.

Supply & fix Exhaust fans 300 mm sweep with all fixing accessories required including making hole & regd length of 3 core 1.0 sqmm PVC multistranded copper conductor, and testing complete all as specified and directed.

Supply & fixing water heater storage type metallic outer body and stainless steel inner container, 25 Ltrs capacity, electric suitable for single phase, 50 Hz, AC Supply, 5 star rating, including all necessary fittings and fixture with minimum 1M of three core 2.5 sqmm twisted copper conductor cable PVC sheated, three pin plug top complete with necessary fittings and fixtures all as specified and directed.

S&F sheet metal enclosure, single pole and neutral with a two pin and earth plug and socket with and including one single pole MCB 20. Amps, 240 volts,10 KA complete all as specified and directed.

M&L, sub main wiring with two single core PVC insulated unsheathed FRLSH confirming to IS 694:2010, multi stranded copper conductor (ISI marked with valid CML No), cable 1100 Volt grade, 6 sqmm size drawn in and including non metallic rigid PVC concealed conduit medium grade (ISI marked with valid CML No) not less than 25 mm dia confirming to IS 14930 (Part-I) 2001, with all fitting & fixing accessories including one run single core PVC insulated unsheathed 6 Sqmm FRLSH copper conductor (ISI marked with valid CML No) colour code as a earth continuity and connected upto DB complete all as specified and directed. NOTE: (i) Two run of single core PVC cable with one run of earth conductor and conduit shall be measured as one unit and the quoted rates shall be deemed to be inclusive for cutting chases in wall/pillars/columns etc. of any description for concealing the conduits to required depth & making good the disturbed surface in cement mortar 1:4 including finishing the surface with putty to match with the existing surface.

Supply, install, commissioning and installation of distribution meter box indoor type, factory made out of CRCA sheet 2mm thick complete with inside, outside powder coated independed housing for meters with transperent glass & rubber gasket packing with suitable size copper single/ two core wire for each control, cable gland, with 200 Amp rated TPN aluminium busbar (for outgoing) duly insulated (including self insulated) maintaining proper space for each busbar and grouting panel in wall etc complete including self closing locking arrangement and comprising for following fittings incl taking down existing MCB DB TPN 4 way:- (i) MCCB TPN, 63 Amps ,16 KA - 01 No (For incoming) (ii) Amp Meter (0-100 Amp)- 01 Nos (iii) Volts Meter (0-500 Volts ) - 01 No (iv) Indicator Lamp set of three R,Y,B - 01 Set (v) ASS & VSS with CTs -02 Nos ( 01 Each) (vi) MCB SP 40 Amps, 230 volts - 04 Nos (For outgoing)(vii) Nutral bus bar link mounted on insulator. (viii) Place for fixing the energy meter. - 04 Nos (ix) The quoted rate is inclusive of removing the existing electric meter from the building and re fixing the same in the sheet metal enclosure at the same location without any damage to the meter. Note;- (i) Cable entry gland made of polycarbonate of appropriated size shall be provided in each cable / wire entry as per IS standered. (ii) All internal wiring inside the panel used for metring purpose shall be PVC insulated FRLSH, ISI marked of size not less than 1.5 Sqmm.

S&F MCB DB, sheet metal enclosures double door SPN 8 way with bus bar 240 volts 2 in 1 shutter type (METAL DOOR) type with blanking plates where required and IP 43 degree protection complete all as specified and directed.

S&F, MCB SPN 40 to 63 Amps, 240 volts 'C' series 16 KA ,including connection with suitable size copper lugs complete all as specified and directed.

S&F, MCB SP 240 volts, 6 to 32 Amps, 'C' series 10 KA including connection with suitable size copper lugs. complete all as specified and directed.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area 35 Sqmm 3.5 Core complete all as specified and directed.

Sand filling in trenches with clean dry unwashed sand free from sharp particles, gently punning around the cables complete.

Bricks, old size sub class `B' laid in trenches with width wise along the alignment of the cable as protection complete.

S&F tube 'Light' grade galvanised Pipe of 50 mm dia with all fitting for cable protection, laid in trenches, fixed to wall and floor by MS shaddle & fixed with pole, 02 position by MS clamp made of 40x5 mm MS flat, complete all as specified and directed.

M&L for earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) vertically, with top edge of plate not less than 1.5 metre below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No 3 of MES Schedule Part-I connecting to earthing test. Testing on completion with and including necessary excavation and earth work in any type soil, earth lead connected to earth test point & to main switch board etc with & including adequate quantity of charcoal dust and common salt, test point, PCC (1:3:6) type C-1 (using 20mm graded BT stone aggregate) for earth pit with 40 x 40 x 6mm mild steel angle iron frame for cover, internal surface of concrete shall be given 10mm thick plaster in CM 1:4, pre cast RCC (1:2:4) type B-1 (using 20mm graded BT stone aggregate) 40mm thick cover, reinforced with 8mm dia deformed or TMT bars 3 Nos both way with 12 mm dia round bar handle, GI medium grade watering pipe 20 mm dia with funnel and wire mesh and 15mm dia GI medium grade earth lead protection pipe including provn of earth test point made of 50 x 5 mm MS Flat in 'D' shape 500 mm legth grouted in wall complete 01 x 6 mm multistrand PVC insulated copper conductor ( Green Colour) to be provided from test point to DB through 20 mm dia concealed non metallic conduit complete all as specified and directed.

Supply, & fix FRP underground water storage Tank of capacity 10000 Ltrs 100% Eco frindly, Rust/leak proof, Duarable light weight, easy to install, Rib design provides additional strength and durability & maintenance free with standard manhole, manhole cover (MS) and provision of inlet, outlet, Vent and necessary FRP straps, Eye bolt, wire rope turn buckle for anchoring and factory made deadmans (concrete block to counter buoyancy) complete all as specified and directed by Engineer in charge.

Supply, install, lowering, testing and commissioning complete open well submersible pump set coupled with electrical opretaed Motors 440 volts, 50 Hz required head not less than 26 mtrs, with discharge capacity not less than 9 LPS, Capacity 5 HP 3 Phase complete with strater and suitable size electric, submersible cable upto panel board all as specified and directed.

Supply and fix in replacement of old UNSV Submersible Controller Fully automatic star delta startor, oil immersed, with contactor and suitable thermal relay suitable for 05 HP, 3 Phase , 415 volts, 50 Hz submersible pump set complete.

Supply, lay , connecting PVC insulated submersible copper cable 3 core, 6 mm², woking voltage 1100 Volts complete all as specified.

Supply & Fixing galvanised steel water tubing of medium grade with all fittings such as bends, elbows, tees, unions, nipples, short pieces etc and fixed complete to walls and ceilings or laid in floors including dismantling existing steel tubing and connections fixed at any location all as directed of size 25 mm dia complete. Note:- (i) The rates quoted inclusive of cutting, jointing and testing of the pipe.

All as per item No. 163 above but of size 20 mm dia.

Supply & Laying in trenches galvanised steel water tubing of medium grade with all fittings such as bends, elbows, tees, unions, nipples, short pieces etc as required at site, including dismantling and taking out old unserviceable pipe line alongwith fittings from existing connections of size 50 mm dia complete all as specified and directed. Note :- (i) Excavation and earth work shall be measured and paid seperately under relevant item of Sch A (ii) The rates quoted inclusive of cutting, jointing and testing of the pipe.

S&F gun metal gate valves with iron wheel head screwed at both ends for iron pipes complete including dismantling of old unserviceable gate valve fixed at any location of Size 50 mm dia all as directed.

All as per item No. 166 above but of size 25 mm dia.

Supplying, laying, testing and commissioning of XLPE insulated screened PVC bedded galvanised steel strip or wire armured electric power cable (Heavy duty ) with aluminium conductor 1100 volts grade, cross sectional area 10 Sqmm 4 Core

Supply, install, testing and commissioning complete Centrifugal Mono block pump set coupled with electrical opretaed Motors 440 volts, 50 Hz required head not less than 75 mtrs, suction/delivery 200 mm x 150 mm dia, with discharge capacity not less than110 LPS, Cap 150 HP, 1500 RPM, including fixed on suitable size MS angle placed on PCC foundation and grouting with suitable size/Nos Nut bolts & water supply suction and delivery pipe line connection including in required size or length of suction and delivery DI pipe line fixed in existing UG Sump & Delivery line & electrical connections all as required at site complete and directed by engineer in charge. Note:- (i) Quoated rates are includes, PCC foundation work, Nut bolts, MS chanel work, all elctrical connections and suitable size of Copper/aluminium cable (if required on site) not more than 10 RM complete (ii) DI Pipe & fittings Should be Measure and Paid separetaly.

M/S MAHAVIR SINGH

M.S. ENGINEERS

MAHARAJ KUNWAR SAHAB CONSTRUCTION

mahamaya constructions

BHAGIRATH CONSTRUCTION COMPANY

M/s J.B. Construction

J.N.R. Engineers and Builders