SPECIAL REPAIRS TO BLDG NO 48, 33, 35 AND PROVN OF ONE TOILET NEAR BLDG NO 52, 4 X URINAL POINTS NEAR BLDG NO 33 OF NCC OTA AT GE KAMPTEE.

Amount

Dismantling of asbestos cement (Corrugated, semi corrugated etc) of any thickness including ridges, hips, valleys as in roof covering complete all as specified and directed.

Dismantling timber scantlings un framed 40 sq cm and over in section, in any position complete all as specified and as directed.

Dismantling of timber fillets unframed under 40 sq cm in section complete all as specified and directed.

S&F mild steel work such as roof trusses (framed), trussed, purlins and heavy bracket framing (Beam, Tee, angle, Channel or flat section) including distance pieces, cleat etc complete all as specified and directed.

M&L for 0.50mm thick prepainted galvalume aluminium zinc coating GI based corrugated steel sheet of on colour having tensile strength of 550 MPA as in roof covering, fixed with and including self tapping screw all as per manufacturer instructions complete all as specified and directed.

M&L for 0.50mm thick prepainted galvalume aluminium zinc coating GI based plain steel sheet of on colour having tensile strength of 550 Mpa as in ridges/ valley, fixed with and including self tapping screw as per manufacturer instructions complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar beddeing (but not backing), removing serviceable tiles to store and debris complete all as specified and as directed.

M&L for coloured non skid ceramic tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed with white or coloured cement to match over and including 15mm thick screed bed of cement mortar (1:6) etc complete all as specified and as directed.

M&L for glazed ceramic coloured tiles 300mm x 450mm, on vertical surface such as skirtings/ dados set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in CM 1:4 finished even and fair complete all as specified and directed.

M&L for non skid ceramic tiles 7 to 8mm thick area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over 15mm thick screed bed of cement mortar (1:6) complete all as specified and directed.

All as per item No 10 above but as in skirting with 10mm backing coat in cement mortar 1:4 complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) or insulation boards/ slabs/ blankets any thickness and wall paneling including cover fillets complete all as specified and directed.

M&L for 4mm thick for non asbestos, fibre cement building board of size 595 x 595mm, fixed over snap grid framework for false ceiling comprising of the following section for making partition of 600x600mm size, fixed to wall with rawl plug and screw and hanged to roof with 4mm dia GI suspended wire of suitable length and butterfly clip of size of main Tee shall be 32mm x 24mm x 0.30mm, cross tee shall be 28mm x 24mm x 0.30mm thick with black lining in mid portion and wall angle shall be 24mm x 24mm x 0.30mm thick complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in platforms etc complete all as specified and directed.

M&L for machine cut cudappah stone slab 20-25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete complete all as specified and directed.

Demolition of brick work, built in cement mortar or cement lime mortar including all quoins, pillars etc. and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 50m complete all as specified and directed.

M&L for brick with fly ash bricks, old size, straight or curved on plan exc 6m mean radius built in CM 1:6 complete all as specified and as directed.

All as per item No 17 above but half brick thick wall in CM 1:4 complete all as specified and directed.

M&L for 40mm thick damp proof course to horizontal or vertical surfaces including necessary formwork in 1:2:4 type B-0 complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water, etc including removal of debris, complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 on fair faces of brick work or concrete surfaces finished even and fair complete all as specified and directed.

M&L for rendering 15mm thick on brick work or concrete surfaces with CM (1:6) finished even and even complete all as specified and directed.

M&L for rendering 10mm thick on surfaces of ceiling in cement mortar (1:3) and finished even and smooth without using extra cement complete all as specified and as directed.

Cutting grooves in brick wall, 75mm wide and 65mm deep and shaping horizontal face of groove with cement mortar 1:3 complete all as specified and directed.

S&F wire netting of galvanised steel wire 0.71mm dia and size of mesh is 12mm fixed in properly with suitable nails for repair of cracks at various locations in wall, beam, chajja, facia, slab, lintel etc including taking down plaster of cracked portion and making good the area by rendering in CM 1:3 complete all as specified and directed.

M&L for preparation of new plastered surfaces and applying three coats of white wash on walls complete all as specified and directed.

All as per item No 26 above but in ceiling complete all as specified and directed.

M&L for brooming down surfaces of any description and applying two coats of white wash on old decorated surfaces of walls including preparation of old surfaces & filling cracks and holes etc complete all as specified and directed.

All as per item No 28 above but in ceiling complete all as specified and directed.

M&L for prepartion of new plastered surfaces and applying two coats of oil bound distemper over a coat of primer and wall care putty complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of oil bound distemper over a coat of primer and wall care putty complete all as specified and directed.

M&L for preparation of new plastered surfaces of walls and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for complete removal of existing treatment of old decorated wall surfaces and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed.

M&L for complete removal of existing treatment and applying two coats of exterior grade emulsion paint (colour as approved by GE) over a coat of primer as per manufacturer's instructions complete all as specified and directed. Make of paint:- "Apex ultima" of Asian Paints or equivalent.

Taking down chowkat or frame with shutter (without taking off shutter from the frame) not exc 1.5 sqm each, making good to disturbed surfaces and removing materials from site of work complete all as specified and directed.

All as per item No 35 above but size exc 1.5 sqm and not exc 4 sqm each complete all as specified and directed.

Taking down shutter of any description exc 1 sqm but not exc 2 sqm each and removing from site complete all as specified and as directed.

S&F solid PVC door frame of size 50mmx47mm, made out of 5mm plain colour PVC sheet reinforced with M.S square tube, and fixing in opening as per specifications complete all as specified and directed.

S&F factory made solid PVC moulded door shutter, 28 to 30mm thick (stiles), with 4mm thick moulded laminated PVC sheet on the front face & 4mm plain colour PVC sheet on back face, with wood free EPS, & fixing in frame at site as per specification & drawing complete all as specified and directed.

S&F second class hard wood 35mm thick factory made plain framed, paneled shutter (two panel) with lock rail and panel of 9mm B.W.P. commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS:1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and as directed.

S&F 30mm thick flush shutters, solid core construction with block board, core and plywood face panels, commercial type on both sides complete all as specified and directed.

S&F 30mm thick 2nd class hard wood factory made glazed and skeleton shutter open rebated and prepared to receive glass, gauze etc divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers edges of framing plain chamferred or rounded, fitted with cut and mitred beads for securing glass, gauge etc for doors provided with styles and rails as specified in SSR Part-I, sec - 08, clause 8.24(a), kiln seasoned and chemically pressure treated complete all as specified and as directed.

M&L for steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

All as per item No 43 above, but without glazing bars complete all as specified and directed.

S&F steel ventilator with top hung shutter including hinges steel peg stay complete complete all as specified and directed.

S&F 100mm size butt hinges medium weight, stainless steel (ISI Marked) complete all as specified and as directed.

S&F 125mm size extruded aluminium alloy handles, fabricated type complete all as specified and directed.

S&F 150mm long aluminum, anodised tower bolts of extruded section complete all as specified and directed.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

M&L for applying two coats of synthetic enamel paint over a coat of primer to new wooden surfaces of any description, not otherwise described, over 10cm width or girth including preparation of surfaces complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10cm in width or girth and applying two coats of synthetic enamel paint over a coat of primer etc complete all as specified and directed.

M&L for applying one coat of synthetic enamel paint to old painted wooden surfaces of any description, not oterwise described, over 10cm width or girth including preparaton of surfaces complete all as specified and directed.

M&L for preparation of old steel surfaces of any description over 10cm in width or girth and applying one coat of synthetic enamel paint etc complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

M&L for 4.0mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 Sqm in each panes complete all as specified and directed.

Demolition of un-reinforced cement concrete in any description and in any position and disposal of unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified and directed.

M&L for PCC 1:4:8 type D2 (using 40mm graded stone aggregate) for foundation, filling and mass concrete complete all as specified and directed.

M&L for 75mm thick PCC 1:4:8 type D2 (using 40mm graded stone aggregate) for floor, sub base complete all as specified and directed.

M&L for 100mm thick PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in flooring, finished even and smooth using extra cement complete all as specified and directed.

M&L for 50mm thick cement concrete 1:2:4 type B-1 (using 20mm graded stone aggregate) as in path/hard standing and surface finished even and smooth without using extra cement etc complete all as specified and directed.

M&L providing 25mm thick cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate), as in sub base in floor/ paving etc complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6) type C1 (using 20mm graded stone aggregate), as in plinth protection and finishing surfaces even & smooth without using extra cement complete all as specified and directed.

M&L for pre-polished machine cut kota stone slab flooring 18-20mm thick over cement screed base of 20mm thick in CM 1:4 laid and jointed with grey cement slurry mixed with pigments to match the shade of the slab complete all as specified and directed.

All as per item No 63 above but in skirting over & including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M&L for sand filling under floor or in foundation including watering and consolidation etc complete all as specified and directed.

M&L for machine pressed precast conctete interlocking paver block of any shape and size confirming to IS 15658-2006 of 80mm thickness M-40 Grade etc complete all as specified and directed.

M&L for PCC 1:2:4 type B1 (using 20mm graded stone aggregate) as in cills, steps, seismic and other similar bands, plinth courses, lacing courses parapets and railing upto 60cm height, copings, kneelers, bed plates, hold fasts block, filling on pressed steel door frame etc complete all as specified and directed.

M&L for framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

Cutting chases for concealed water tubing or concealed conduit wiring, etc and making good, cutting not exc 10cm girth in cement mortar 1:3 complete all as specified and directed.

S&F GI tubing 15mm bore, medium grade with all fittings and fixed to wall including taking up or down existing steel tubing and connections complete all as specified and directed.

All as per item No 70 above but 20mm bore complete all as specified and directed.

M&L for 15mm dia GI tubing 'Medium grade' with all fittings and fixed complete to wall and ceiling or laid in floors complete all as specified and directed.

All as per item No 72 above but 20mm bore complete all as specified and directed.

S&F in repairs rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) of 1000 litres capacity, hoisted and fixed in position complete all as specified and directed.

S&F rotational moulded polyethylene water storage tankof 500 ltr capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified and directed.

S&F 20mm bore ball valves, high pressure of PTMT with epoxy coated aluminum rod & high dencity plastic ball, screwed for iron pipe and fixed (Minimum weight 20mm - 210g) complete all as specified and directed.

S&F stop valve 15mm dia, cast copper alloy, chromium plated, fancy type, high pressure with crutch or butter fly handle screwed for iron pipe or union and fixed complete all as specified and directed.

All as per item No 77 above but fixed in repairs complete all as specified and directed.

S&F bib tap 15mm dia, cast copper alloy, chromium plated, fancy type with crutch or butter fly handle screwed for iron pipe or for brass ferrule complete all as specified and directed.

All as per item No 79 above but fixed in repairs complete all as specified and directed.

S&F pillar tap 15mm dia, cast copper alloy, with capstan heads, chromium plated, screwed down, high pressure with or without lettered Hot or Cold with screwed shanks and fly nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair long shank and cup (concealed type) stop valve 15mm dia chromium plated, fancy type, high pressure with crutch or butterfly handle screwd for iron pipe or union and fixed complete all as specified and directed.

S&F in repairs 125mm long shower rose, chromium plated with or without swivel joints including fixing to 15mm bore of pipe complete all as specified and directed.

S&F CP grating of size 100mm dia complete all as specified and directed.

S&F towel rail 20mm dia of chromium plated, fixed with and including chromium plated brass screws and wooden/ plastic cleats complete all as specified and directed.

S&F vitreous china urinal, half stall pattern, white (excluding flushing cistern, flush pipe and waste pipe) including urinal spreader, connections to flushing pipe complete all as specified and directed.

All as per item No 87 above but fixed in repairs complete all as specified and directed.

S&F 15mm bore CP push cock and CP urinal spreader for urinals complete all as specified and directed.

S&F in repairs vitreous china squatting pan "Orissa Pattern" of size 580x 440mm, white with integrated foot rest (excluding flushing cistern, flush pipe etc) including making good to floor complete all as specified and directed.

S&F 100mm dia cast iron 'S' trap, including jointing with solvent cement complete all as specified and directed.

S&F 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F vitreous china wash down water closet pan (pedestal pattern) including plastic water closet seat, white/black, closed pattern with flat bottom and cover and mild steel chromium plated or aluminium hinging device including flush pipe and fixing bolts (excluding flushing cistern) etc complete all as specified and directed.

S&F in repairs wash hand basin (flat back or angle back) of size 550 x 400mm, white including, waste pipe, chain and plug, porcelain stopper including for & pinning in ends of brackets including S&F waste pipe complete all as specified and directed.

S&F vitreous china wash basin with pedestal of size 550x400mm including waste coupling, cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S&F in repairs 10 ltr capacity PVC valve less symphonic action type flushing cistern low level, white with inlet ball valve, float and handle including bracket etc complete all as specified and directed. Make:- Prayag Cat No 501 or equivalent.

S&F flushing pipe, polyethylene of low or high density or PVC, 32mm dia, for low level cistern complete all as specified and directed.

S&F in repair PVC connection of 15mm dia, 450mm long including PTMT check nut complete all as specified and directed.

S&F PVC (SWR) pipes of 75mm bore, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and directed.

S&F prelaminated particle board, interior grade prelaminated one side decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

S&F continuous (piano) hinges, brass, bright finish complete all as specified and directed.

Taking down existing water proofing treatment including PCC padding, mortar etc and disposal of rubbish outside of MD land and hacking for key, scrubbing down with water complete all as specified and directed.

M&L for provision of water proofing treatment by using APP torch on fibre glass base finished membrrance over roof and vertical surfaces including preparation of surfaces and applying oil based bituminous primer coat @ 0.30 ltr per sqm on clean and dry surface and then providing APP membrane having non woven polyster film reinforcement with 3mm thick and weight not less than 3.00 kg/sqm and finished on top with mineral/slate finished torch on system laid with 100mm & 150mm over lap on side & end laps resepectely all as per manufacturers instructions over and including rendering 20mm thick in cement mortar 1:4 on concrete surfaces complete all as specified and directed.

Surface excavation in soft/loose soil not exc 30cm deep and averaging 15cm deep and getting out etc complete all as specified and directed.

Excavation in trenches not exc 1.5m in deepth and 1.5m in width and getting out in soft/loose soil complete all as specified and directed.

M&L for form work to sides of concrete in foundations, footing base, base of columns, sides and soffits of plinth beam and similar work complete all as specified and directed.

M&L for providing reinforcement cement concrete 1:1.5:3 type A-1 (Nominal Mix) as in footing, foundation, beams, plinth beams, base for columns and mass concrete etc complete all as specified and directed.

M&L for form work to sides of columns and similar work complete all as specified and directed.

M&L for providing reinforcement cement concrete 1:1.5:3 type A-1 (Nominal Mix) as in columns and pillars etc complete all as specified and directed.

M&L for form work to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, and similar work complete all as specified and directed.

M&L for providing reinforcement cement concrete 1:1.5:3 type A-1 (Nominal Mix) as in beams, cantilevers, bressummers, lintels over 1.5m span concrete etc complete all as specified and directed.

M&L for form work to chullah hoods, chajjas, troughs and similar items including edges and similar work complete all as specified and directed.

M&L for providing reinforcement cement concrete 1:1.5:3 type A-1 (Nominal Mix) as in chajja etc complete all as specified and directed.

M&L formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs not exc 20cm wide complete all as specified and directed.

M&L for providing reinforcement cement concrete 1:1.5:3 type A-1 (Nominal Mix) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likes complete all as specified and directed.

M&L for mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending and binding with mild steel (annealed) wire not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT bars 8mm dia in spacers, cut to length, bent to shape required, including cranking, bending and binding with mild steel (annealed) wire not less than 0.9mm dia complete all as specified and directed.

M&L for mild steel TMT bars 8 to 10mm dia as in stirrups, spacers and binders complete all as specified and directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers not exc 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M&L for hardcore of gauge not exc 63mm deposited, spread and levelled in layers not exc 15cm thick, watered and rammed to a true surface for plinth protection/ path complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/ dense soil complete all as specified and directed.

Removing excavated material (soil) not exc 50m and deposited where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

S&F 100mm dia cast iron soil, waste and vent sand cast pipes in any length with or without ears, with cement joints, laid in trenches or in floors complete all as specified and directed.

M&L for providing concrete bed to drain pipe including packing under and haunching against the sides of pipes after they are laid and tested, in cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) complete all as specified and directed.

S&F cast iron cowl slotted vent cowl 100mm size complete all as specified and directed.

M&L for providing cement concrete 1:2:4 type B2 (using 40mm graded stone aggregate) as in foundation, mass concrete and fillings complete all as specified and directed.

M&L for precast reinforced cement concrete 1:2:4 type B1 (using 20mm graded stone aggregate) as in landings, cover slabs (for manholes etc) chullah hoods, chajjas, mangers, shelves and similar articles with plain faces and set in CM 1:6 (reinforcement measured and paid separately) complete all as specified and directed.

Taking down unserviceable point wiring with copper / aluminium conductor cable of (light, fan, plug & power plug point) complete including light fittings any type switches, sockets, ceiling rose, switch boards, bell / buzzer, bell push, tube light fitting, regulator etc, and making good to the disturbed surfaces of walls / floor etc to macth with existing surfaces including white washing / colour washing /distempering complete all as specified and as directed.

Taking down old unserviceable MCB, sheet metal enclosure, DB, main switch etc and making good distrubed sufaces of wall complete all as specified and as directed.

Taking down carefully unserviceable sub main wiring of any size/ capacity and making good disturbed sufaces to match with the existing surfaces complete all as specified and directed.

M&L for point wiring 1100 volt grade single core FRLSH PVC insulated & unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marking medium grade on surface of wall/ceilling including FRLSH PVC insulated unsheathed earth wire with copper conductor of size 1.50 sqmm pressed steel terminal modular boxes sunk on wall for mounting of switches switch sockets fan regulator etc including modular white cover plate suitable for mounting modular switches, sockets, fan regulator etc complete all as specified and making good to distrubed surfaces for one light point controlled by one, one way switch. Note: Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, cieling roses and holders shall be connected to common earth dolly.

All as per item No 133 above but one ceiling /exhaust/ wall mounted fan point controlled by one switch and regulator complete all as specified and directed.

All as per item No 133 above but one 3 pin 5 amp socket out point on the same board with other switches complete all as specified and directed.

All as per item No 133 above but one 3 pin 5 amp socket out point on independent board complete all as specified and directed.

All as per item No 133 above but wiring with 4.0 sqmm multi stranded cable and earth wire with copper conductor of size 4.0 sqmm for 15 amps power point complete all as specified and directed.

M&L for point wiring 1100 volt grade single core FRLSH PVC insulated & unsheathed cable with multistranded copper conductor 1.50 sqmm drawn in electrical grade PVC conduit not less than 20mm dia with IS 9537 (Part-III) 1983 marking medium grade concealed in surface of wall/ceilling including FRLSH PVC insulated unsheathed earth wire with copper conductor of size 1.50 sqmm pressed steel terminal modular boxes sunk on wall for mounting of switches switch sockets fan regulator etc including modular white cover plate suitable for mounting modular switches, sockets, fan regulator etc complete all as specified and making good to distrubed surfaces for one light point controlled by one, one way switch. Note: Cost of cable provided from sub main DB to respective switch board in rooms shall be included in the quoted point wiring rate. All switches, fan, sockets, cieling roses and holders shall be connected to common earth dolly.

All as per item No 138 above but one ceiling /exhaust/ wall mounted fan point controlled by one switch and regulator complete all as specified and directed.

All as per item No 138 above but one 3 pin 5 amp socket out point on the same board with other switches complete all as specified and directed.

All as per item No 138 above but one 3 pin 5 amp socket out point on independent board complete all as specified and directed.

All as per item No 138 above but wiring with 2.5 sqmm multi stranded cable and earth wire with copper conductor of size 2.5 sqmm for 15 amps power point complete all as specified and directed.

M&L for sub main wiring with 2 single core FRLSH PVC insulated, unsheathed, multistranded, copper conductor wie 2x4.0 sqmm, 1100 V grade including and 1x4.0 sqmm PVC insulated, multistranded unsheathed copper wire, as earthing lead drawn through and including PVC conduit not less than 20mm dia marking medium grade concealed in wall/ ceilling and accessories complete all as specified and directed. Note:- Accessories for point/ sub main wiring like PVC junction box, bend, tee, elbow shall be of same make.

All as per item No 143 above but 2 x 6.0 sqmm with earth wire of 1 x 6.0 sqmm complete all as specified and directed.

All as per item No 143 above but 2 x 2.5 sqmm with earth wire of 1 x 2.5 sqmm complete all as specified and directed.

S&F switch, modular type, single pole, one way, 6 amp, 1 module, 250 volts AC suitable for modular switch boxes complete all as specified and directed. Make:- Legrand / Crabtree / Schneider.

S&F socket, modular type, single pole, one way, 6 amp, 2 module, 2/3 pin, 250 volts AC suitable for modular switch boxes complete all as specified and directed. Make:- Legrand / Crabtree / Schneider.

S&F switch, modular type, single pole, one way, 16 amp, 250 volts AC suitable for modular switch boxes complete all as specified and directed. Make:- Legrand / Crabtree / Schneider.

S&F socket, modular type, single pole, one way, 6/16 amp, 2/3 pin, 2 module, 250 volts AC suitable for modular switch boxes complete all as specified and directed. Make:- Legrand / Crabtree / Schneider.

S&F ceiling rose, surface type, 2/3 terminal, 5 amps complete all as specified and directed.

S&F modular type fan regulators 240 volts, 100 watts, 2 module single pole complete all as specified and directed.

S&F LED light fitting surface mounted bulk head luminaries 9-12W with min 800 lumen, IP 65, aluminium housing, surge protection including drivers etc complete with all accessories and including connecting up with twin core twisted flexible cable suitable size of 230V, 50Hz complete all as specified and directed. Make:- Philips Cat No Endura LED 10W, Luker Cat No LBKOVSL04, C&S Cat No Sirus 10W, CG Cat No LBH 10W.

S&F building security light LED 20-25W with lumen output 2000 with driver with rated voltage 240V, 50Hz including mounting GI, made out of 25mm dia light grade pipe 0.8m bent to shape including FI clamps nut bolts etc complete all as specified and directed. Make:- Philips Cat No BRP022 LED 20CW, CG Cat No LSTS-25-CDL, Luker Cat No LST24 WH.

S&F LED baton fitting 2' length including drivers having energy consumption 9/11W, 230V, 50Hz, 6500K not less than 800 lumens prewired complete all as specified and directed. Make:- Philips cat No Smart bright LED 10S, Crompton Cat No LCTLN-20-CDL, Luker Cat No LT509 WH.

S&F 18/20/24W LED tube light fitting complete including tube rod, driver, rated voltage 240V connecting with 2 core 1 sqmm copper conductor cable complete all as specified and directed. Make:- Philips cat No Smartbright LED 20S, CG Cat No LCTLN-20-CDL, Luker Cat No LT824 WH.

S&F 9/11W LED tube light fitting complete including tube rod, driver, rated voltage 240V connecting with 2 core 1 sqmm copper conductor cable complete all as specified and directed. Make:- CG Cat No LCTLN-20-CDL or equivalent in Luker / Philips.

S&F sheet metal enclosure, single pole & neutral for 240 volts, 8 way with 200 Amp rated bus bar flush /surface mounting double door complete all as specified and directed.

S&F sheet metal enclosure, single pole & neutral for 240 volts, 4 way with 200 Amp rated bus bar flush /surface mounting double door complete all as specified and directed.

S&F MCB single pole & neutral, 240 volt, 6 to 40 amps, 10 KA complete all as specified and directed.

S&F MCB single pole, 240 volt, 6 to 40 amps, 10 KA complete all as specified and directed.

Taking down carefully ceiling fan with down rod complete of 1200/1400m sweep from fan hook, dismantling blade, cleaning, servicing, painting with two coats of enamel paint, marking MES number and refixing & connecting with 3 core copper cable complete all as specified and as directed.

M&L for down rod for ceiling fan of any make and size, made out of medium grade GI tubing, 15mm dia provided with holes for electric wire at top and bottom also arrangement of fitment of ceiling fan complete all as specified and as directed.

M&L for mild steel work such as fan hook, angle / FI clamp, MS pipe, nuts, bolts, washers, welding, bending, cold or hot, drilling holes for bolts in any shape and size etc including two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

S&F ceiling fan, 1200mm sweep, BEE 5 star rated with three core wire for connection and accessories complete all as specified and as directed.

S&F wall mounted air circular fan, 450mm sweep complete with twin core 1 sqmm wire for connection complete all as specified and as directed.

S&F exhaust fan, single phase, 300mm sweep, plastic body with shutters, bolts, nuts, washers and connected electrically complete all as specified and as directed.

M&L for making suitable size of holes for 300mm sweep exhaust fan and including grouting bolts, cutting chasing and plastering, white washing etc and match with existing surface complete all as specified and as directed.

M&L for earthing complete with galvanised steet earth plate electrode 600 x 600 x 6mm thick burried directly in ground (earth plate not less than 2.25mtr deep below normal ground level) with top edge of the plate not less then 1.50 mtr below the normal ground level connected to galvanised earth lead wire 4.00mm dia by means of bolts nuts check nuts & washer of galvanised iron or steel all as shown in electrical plate No 5 connected to earthing test point all as specified and testing on completion including the material and labour for:- (a) Excavation and earth work or drilling hole for electrode in any type of soil. (b) PCC pit in cement concrete 1:2:4 type B-1. (c) Pre cast RCC cover with suitable handle 40mm thick in PCC 1:2:4 reinforced with welded steel wire fabric weighting not less than 1.87 Kg/sqmm. (d) Funnel with watering pipe of GI 20mm nominal bore medium grade and Aluminium lugs etc all as specified. (e) 15mm nominal bore meduim grade GI protection pipe upto 7.50 metre long for protection of earthing lead. (f) Reguisite quantity of charcoal and common salt. (g) Connection to earthing test point and testing on completion.

S&F double wall corrugated high density polymer ethyl (HDEP) pipe for laying of electric cable of size 50mm outer dia and 38mm inner dia with IS 14930 (part 2) 2001 and 6mm thickness laid in trenches, wall, floor, pole including bends, sockets and other connected accessories complete all as specified and directed.

M&L for XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volt grade laid in trenches, passing through pipes / ducts including testing for cable of 4 core 16 sqmm cross sectional area complete all as specified and directed. Make:- Polycab / Havells / Finolex.

Excavation in trenches not exc 1.5m in depth and 1.5m in width for laying of cables and getting out in soft/loose soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25cm in hard/dense soil complete all as specified and directed.

Removal of surplus soil to a distance not exc 50m and deposited where directed at a level not exc 1.5m above the starting point complete all as specified and directed.

NOTE:- SCHEDULE OF CREDIT (Amount shall be deducted offline from the total quoted amount to workout the net contract sum to be considered for acceptance.) [(-) Rs.49,388.00]

M/s T.S.JOHAR

Vishwakarma Engineering Works

NORTH INDIA PEST CONTROL

M/s Jagdish Staioners and General Stores

M/s Rahul Traders

Devika Constructions

M/s DS Khekde

Bidder Name

Vishwakarma Engineering Works

M/s T.S.JOHAR

M/s Rahul Traders

M/s DS Khekde

Devika Constructions

M/s Jagdish Staioners and General Stores

M/s M.G. Hargunani

NORTH INDIA PEST CONTROL