PROVN OF WATER DRAINAGE SYSTEM PROVN OF HARDSTANDING AND CERTAIN MINOR WKS AT BHALUKMARA AND MINOR WKS AT ROWRIAH AREA IN JORHAT MIL STN UNDER GE JORHAT

Amount

NOTES :(i)The bidders/contractors are advised to read tender document & all corrigendum/ amendments and General conditions of contracts before entry/quoting the rates.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation etc. or for shafts, wells, cess pits, manholes, pier holes etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out as in soft/loose soil.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil

Removing excavated material (soil) not exceeding 50 m and depositing where directed at a level n. exc. 1.50 m above the starting point.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm as in soft/loose soil.

Material and labour for Spreading of cow dung manure and good earth (1:-4) in required thickness as per complete all as specified and directed. Note:- The cost of manure and good earth to be measure and paid in thiss item. The anure measured in stacks will be reduced by 8% for payment and earth measured in stacks will be reduced by 20% for payment

Material and labour for planting and developing doob grass (Cynodon dactylon) including following: (a) Preparing soil base by excavation/ploughing and loosening of ground upto 15cm and removing unwanted material, grass stones etc to a distance exceeding 50m but not exceeding 250m. (b) Mixing good earth(fresh garden soil) & farm yard manure thoroughly in 3 : 1 proportion and filling in excavated area to a height of 15 cm and leveling completely.(Note:- Good earth(fresh garden soil) & farm yard manure shall be measured and paid for separately) (c) Watering on previous night and planting required variety of lawn grass and maintaining for a minimum period of 90 days or till formation of well established lawn grass whichever is later blanket to the satisfaction of Engr-in-Charge by watering, weeding, clipping and rolling etc complete.

Bringing approved earth (as approved by Garrison Engineer) from sources outside defence land including all cost such as royalty if any, transportation, taxes etc. for area filling/ forming embankments including raising(any height from EGL)/lowering by approved earth and including raising earth spreading in layers not exc 30cm thick each layer, watering, compaction with 8 tonne to 12 tonne power roller and finished to required size and shape etc, any high/depth from EGL. Notes for : (i) Earth required for the item, shall be supplied by contractor, from out side MOD land of any lead, at his own arrangement. (ii) All cost of procurement of earth including cost of transportation, compaction, royalties, tax etc shall be deemed to be included in the unit rate quoted by the contractor. (iii) With reference to clause 3.6 of MES schedule Part-II on serial page No.21 it is clarified that measurement of the above item shall be of finished embankment/traverse of filled earth after consolidation/compaction and 5% deduction shall be made from measured and calculated volume to allow for increase in bulk.

Material and labour for Plain Cement Concrete M-7.5(Nominal Mix) using 40 mm graded stone aggregate as in foundation filling and mass concrete

Material and labour for Reinforced Cement Concrete M-20 (Nominal mix) using 20 mm graded stone aggregate as in foundation & plinth beams

Reinforced Cement Concrete M-20 (Nominal mix) using 20 mm graded stone aggregate as in beams and Lintel Beam complete all as specified and directed.

Reinforced Cement Concrete M-20 (Nominal mix) using 20 mm graded stone aggregate as in column complete all as specified and directed.

Precast Reinforced Cement Concete cover slab type M-20(Nominal Mix) using 20 mm graded stone aggregate, set in Cement Mortar (1:4) complete all as specified and directed.

Use and Waste of formwork for foundations, foundation beams etc. for rough finished surfaces of concrete.

Use and waste of formwork to sides of columns

Use and waste of formwork to sides and soffits of floor or roof beams, lintels, cantilevers, shelves for flat surfaces

Material and labour for TMT Bars Fe 500D 10mm dia & over cut to length bent to shape required inculding cranking bending spirally hooping for columns etc and binding with MS wire ennealed less than 0.9mm dia or securing with clip complete all as specified and directed.

Material and labour for High strength steel TMT bars 6 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders, cut to length, bent to shape required including cranking, bending spirally and binding with and including mild steel (annealed) wire not less than 0.90 mm dia

Material and labour for 25 mm thick Plain Cement Concrete 1:2:4 type B0 using 12.5 mm graded stone aggregate as in Damp proof course to horizontal or vertical surfaces including necessary formwork

Material and labour for Brick work with bricks class designation 75, old size, straight or curved on plan exceeding 6 m mean radius built in Cement Mortar 1:6 complete all as specified and as directed.

Material and labour for brick work with bricks class designation 75, size as per old size brick, straight or curved on plan exceeding 6 m mean radius half brick thick walls built in Cement Mortar 1:4 complete all as specified and as directed.

Rendering 15 mm in Cement Mortar 1:6 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement to the plastered surface complete all as specified and as directed.

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment. Note:- Water proofing compound shall be measure and paid separately

Material and labour for Rendering 15mm thick plaster in Cement Mortar (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, with water proofing treatment.

Supply only integral liquid water proofing compound complete all as specified and directed.

Plain Cement Concrete M-15(Nominal Mix) using 12.5 mm graded stone aggregate as in making good window opening, lintels upto 1.5 m clear span, cills, steps, seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, coping, kneelers, apex stones, bed plates, kerbs, water trough and the like including weathering slightly rounded or chamfered angles and throating complete all as specified and directed.

Material and labour for Preparation of new plaster surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer over a coat of 1.5 mm thick cement base wall putty complete all as specified and directed.

Material and labour for Preparation of new plster ceilig surface and applying two coats of 1st quality acrylic washable distemper (ready mixed) having VOC content less than 50 gms/litre of required colour shade and as per manufacturer’s specification over a coat of primer complete all as specified and directed.

Material and labour for Preparation of new surface and applying 3 coats white wash on walls complete all as specified and as directed.

Material and labour for preparation of new surfaces and and applying 2 coats of cement based paint over a coat of alkali based primer complete all as specified and directed.

Rolled mild hollow steel sections steel of grade YSt 310 conform to IS 4923-1997 in roof trusses (framed), trussed, purlins, bracing and fastenings including distance pieces, cleats etc. Note:- The steel trusses shall be provide as per TD no CESZ/STD/26.

Supply and fixing of pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick and pitch length 75 mm c/c of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

Supply and fixing of pre-painted galvatume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridges, tips, valley, gutters, length & girth as fixed with nail or screws complete all as specified and as directed.

Material, labour and fixed of aluminium snap grid frame work for false ceiling, size of grid 605 x 605 mm, including aluminium main/closs tee of size 35mm x 23mm x 1.5 mm ( minimum) aluminum BULBED TEES section and aluminium angle of 25mm X 25mm X 1.5mm thick, sutiable type GI wire hanging arrangement with adjuster all as specified in clause no 10.38 in SSR part-I and including 4mm thick high pressure steam cured non asbestos fibre cement designer board as per IS 14862 with applying of two coats of acrylic distemper over a coat of primer complete all as specified and directed.

Material and labour for 75 mm thick plain cement concrete M-10(Nominal Mix) using 20 mm graded stone aggregate as in plinth protection, finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 75mm thick plain cement concrete 7.5 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Hard core of gauge not exceeding 63 mm of broken stone or boulders , spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface

Material and labour for 100mm thick plain cement concrete 7.5 (Nominal Mix) using 40 mm graded stone aggregate as in sub base floor complete all as specified and as directed.

Material and labour for 100 mm thick plain cement concrete M-15(Nominal Mix) using 20 mm graded stone aggregate as in floor laid in alternate panel (2mx2m), finished even and smooth without using extra cement complete all as specified and as directed.

Material and labour for Forming 12 mm thick expansion joints filled with compressible filler board and top 30 mm filled with polysulphide sealant, thickness of concrete slab in 100 mm all specified in relevant para & sub para of 20.B.7 in SSR Part-I complete all as directed.

Material and labour for Forming Contraction (Dummy) joints 30mm deep x 10mm wide, filled with polysulphide sealant all specified in relevant para & sub para of 20.B.7 in SSR Part-I complete all as directed.

Material and labour for Sand filling under floors or in fdns incl watering and consolidation

Material and labour for Plain Cement Concrete M-15(Nominal Mix) using 20 mm gaded stone aggregate as in Surface channel and drain

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc.

Add or deduct for each 25 mm girth or part thereof over or under 30 cm inner girth in cement concrete complete all as specified and directed.

Material and labour for pre-polished chequered Cement Concrete tiles of 25 mm minimum thick, size of (square/ rectangular) area of each tile exceeding 0.09 Sqm but not exceeding 0.16 Sqm double layer machine pressed set ( as per IS 1237-2012), jointed and pointed in neat cement slurry in floors and cut & polished in white or coloured cement to match over and including 15mm thick screed bed in CM (1:6) complete all as specified and as directed.

Material & Labour Non skid ceramic tiles, coloured, 7 to 8 mm thick (square/rectangular area of each tile exceeding 0.06 Sqm and not exceeding 0.11Sqm , in floors etc. Set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed layer in CM (1:4) including roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushign neat cement slurry with 3.0 kg of cement per Sqm complete all as specified and as directed.

Material & Labour Glazed ceramic tiles 450x300x7 mm(Coloured) on vertical surfaces such as skirting, dados and riser to steps etc. set and jointed in neat cement slurry and pointed in coloured cement to match complete over 10mm thick screed bed vertical layer in CM (1:4)all as specified and as directed.

Material & Labour of Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658 of 60mm thickness, M-35 grade with grey cement and pigment complete all as specified and as directed..

Materials and labour for Rolled mild steel of grade Fe-410-W (Gde E-250) (quality A) in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., omplete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete. complete all as specified and as directed.

Supply and fixing of pressed steel door frames (fabricated out of CRLCS sheet 1.6 mm thickness) 125 x 60 mm size with one or more rebates including necessary fixing lugs, hinges, lock striking plate etc. complete all as specified and as directed.

Supply and fixing of 35 mm thick flush shutters, solid core construction, with block board core and comercial plywood face panels with one face is covered with decorative face veneer with lipping/frame to match all complete all as specified and as directed.

Material and labour for Solid PVC door frame of size 50mm x 47 mm made out of 5 mm wood grain printed PVC sheet reinforced with Mild Steel square tube, suppling & fixing in opening as per drawing complete all as specified and directed.

Material and labour for Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and wood grain printed PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawingcomplete all as specified and directed.

Materials and labour for Mild Steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290(Gde E-165) complete all as specified and as directedincluding taking dwon old one complete all as specified and as directed.

Supply and fixing of aluminium sliding window with powder coating (minimum thickness of powder coating 50 micron) including following components / specifications complete all as specified and as directed. (i) Two leaf glazed sliding shutter and one leaf gauged (fly proofing) sliding shutter. (ii) Opening of windows exceeding 0.90 Sqm but not exceeding 1.50 Sqm (iii) Thickness and weight per metre length of aluminium frame and section of shutter all as shown on drawing. (iv) All vertical/ horizontal joints shall be of extruded aluminium section so as to avoid any play between jointed members. (v) All other accessories such as jointing cleats, glazing clips, rubber neoprene packing, anodised aluminium snap beading, screws, etc. (vi) Rest all as specified in drawing no CESZ/2015/TD/007 Sheet no 1R/5, 2R/5, 3R/5, 4R/5 & 5R/5. Note Nos :- (i) All window member including fitting & fixture i.e window frame, shutter frame, mullion, clip section, hingh, handle , lock etc shall be deem to included quoted rate. Only measure opening size of window. (ii) Only Glass & wire mesh shall be measure and paid separately under relevant items of BOQ .

Supply and fixing of aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum thickness of powder coating 50 micron) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and complete all as specified and directed.

Supply and fixing of steel ventilator with top hung shutters including hinges with steel handle and steel peg stay complete without gauged bars, dovetailed or welded complete all as specified and as directed

Supply and fixing of sheet glass 5 mm thick ordinary quality fixed to aluminum door & window in squares in each pane of required size complete all as specified and as directed.

Supply and fixing of Glazing with sheet glass (frosted on one side) 4 mm thick ordinary quality with oil putty in square not exceeding 0.5 Sqm in each pane.

Supply and fixing of Butt hinges Stainless steel 100 mm size complete all as specified and directed.

Supply and fixing of Aluminium anodised barrel tower bolts of extruded section size 150 mm complete all as specified and directed.

Material and labour for Stainless steel wire cloth, 0.43 mm nominal dia of wire and avergae width of aperture 1.00 mm and fixed with stainless steel wire staples complete all as specified and directed.

Material and labour for preparation of new steel surface and applying two coats of synthetic enamel paint over a coat of red oxide primer on new steel and iron surfaces of any description over exceeding 10 cm in width or girth complete all as specified and as directed..

Material and labour for Painting 2 coats of synthetic enamel paint on wooden surfaces of any description over 10 cm in width or girth including preparation new surface and one coat of pink primer complete all as specified and as directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

Supply and fixing of 15mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed.

Supply and fixing of 20mm bore galvanised steel tubes, medium grade with all fitting and fixed to walls, ceiling, floors complete all as specified and as directed. Note for item no67 & 68:- All fitting & fixture such as Bends, Elbows, Tees, Short Pieces, Connectors, Back - Nuts Caps, Plugs, Unions, Flange (core) & flange (ring), reduction Tee, reducing socket, Male & female threaded socket, tank connector, holding clamp shall be provide as per site requiredment as as directed by AGE and same shall deem to be included in quoted rate.

Supply and fixing of 15mm bore stop valve angular type cast copper alloy chromium plated screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe for union 15mm complete all as specified and directed.

Supply and fixing in repair of bib cock cast copper alloy screwed down with long body with wall flange, and fixed for 15 mm bore GI tube pipe and all accessories complete all as specified and as directed. complete all as specified. Make :- Cat no PIS -08 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of vitreous china wash basin white flat back, size 550 x 400 mm including CP waste coupling,with GI pipe brackets & , rag bolt in cement concrete/brick wall and including taking down existing HWB and making good wall surface complete all as specified and as directed. Make: Cat no S2040103 wash basin of CERA or equivalent model of make list as given in PS as approved by GE.

Supply and fixing as in repair of PVC low level flusing cistern 10 litres capacity white with ball valve & brackets with flush pipe complete all as specified and as directed. Make: CHIVAS of CERA or equivalent model of make list as given in PS as approved by GE.

Supply and fixing of Vitreous china wash down water closet (pedestal pattern) with concealed S-trap or P-Trap, white, 410 mm high(minimum), seat cover including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe etc a complete all as specified and as directed Make: CIGNIA Concealed of CERA or equivalent model of make list as given in PS as approved by GE.

Supply and fixing as in repair of PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and as directed.

Material and labour for Soap dish chrome plated complete all as specified and as directe

Supply and fixing in repairof Towel Rail 600 mm long of chromium plated fixed with and including chromium plated brass screws and wooden/plastic cleats complete all as specified and as directed. Make :- Cat no BA-40 of Prayag or equivalent model of make list as given in PS as approved by GE.

Supplying, hoisted and fixed in position of rotational moulded polyethylene water storage tanks in double layers and cylindrical vertical type with manhole lids(closed top) of 500 litres capacity with ISI marked and all as specified in IS 12701 and including taking down existing water tank complete all as specified and directed .

Supply and fixing of PVC ball valve for 20 mm dia GI pipe all complete complete all as specified and directed.

Supply and fixing of uPVC of type-B for use in soil and waste discharge systems, single socket, 110 mm bore in any length including rubber ring joints and fixed to walls with clips and other standard material and all as specified in IS 13592 complete all as specified and directed.

All as per item no 75 above but 75mm bore complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )bend for 110 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )bend for 75 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )juction equal or unequal for 110 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of Unplasticized (uPVC )juction equal or unequal for 75 mm bore uPVC pipe complete all as specified and directed.

Supply and fixing of PVC(SWR) vent cowl, 75 mm bore

Supply and fixing PVC (SWR) floor trap 75 mm, plain with CP grating including joining and solvent cement complete all as specified and directed.

Supply and fixing of 50 mm dia low density polyethylene (LDPE) pipes of pressure rating 6 kgf/sq. cm fixed complete to walls, ceiling or in floors etc including cutting, chasing, pinning and making floor good with existing one all as directed

Cutting into existing manhole for connecting new drain, making good to pipe & rendering, cutting out existing benching for and forming branch channel (half round or 3/4 section) in cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate for 150 mm bore pipe complete all as specified and directed.

Subtotal of Sch A part-I

SCHEDULE 'A' PART - II FOR B/R PORTION (Sl No __ to ____)

Material and labour for concealed point wiring complete with 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable 1100 volt grade, FRLSH through and including 20 mm PVC conduit & its accessories, cadmium screws fixed in concealed surface of wall/ceiling/false ceiling and including 1.5 Sqmm single core PVC insulated and unsheathed multi stranded copper conductor cable FRLSH as earth continuity conductor and MS boxes made of 16 gauge MS sheet concealed type on walls cover 3mm thick laminated sheet for housing complete switch for One light/fan/bell point controlled by one way switch. Note :- Cutting chases and making good in walls shall be deemed to be included in the unit rate.

All as per item no ___ here-in-above but One 3 pin socket outlet 5 amps on the same board with other switches

All as per item no ___ here-in-above but above but for one 5 amp socket independent complete all as specified and as directed.

Supply and fixing of switch piano flush single pole one way 5 amps complete all as specified and as directed.

Supply and fixing of switch socket outlet 3 pin 6 Amps 230 volts Universal type complete all as specified and as directed.

Material and labour for Electronic type fan regulator step type 120 watt, 230 volt complete all as specified and as directed. Make : Code no 14502 of Anchor or equivalent model of make list as given in PS as approved by GE.

Supply and fixing ceiling rose surface bakelite 65x50mm three terminals complete all as specified and as directed.

Supply and fixing of LED surface/ceiling mounting(suspended from ceiling) box type light fitting 20Watt with LED Lamp , drive and made of epoxy powder coated extruded aluminium channel housing with high quality polycarbonate opal diffuser cover & high power LED’s as light source with 120 Lumen per watt (Minimum) and including all other standard accessories as per manufacture instructions ,internally pre-wired including connecting up three core1.00sq. mm copper conductor flexible wire/cable complete all as specified. Make : Model No LDL-20-CDL of Crompton/ BCLAB 20W WH LED P of Bajaj or equivalent model of make list as given in PS as approved by GE.

Supply and Fixing exhust fan 240V, 300mm sweep, 900 RPM , MS body, highly efficient heavy duty motor with pressure die cast aluminium rotor mounted on two ball bearings and conforming to IS: 2312 and including aluminium lowers and shutters fixed to wall , writing the MES fan numbers with paint and 0.75 Sqmm , 3 core PVC insulated Flexible copper cable for connection from ceiling rose to fan complete all as specified and as directed.

Supply and fixing of sheet metal enclosure for MCBs to be used singal pole & nutral double door 4 Way 200 Amps rated busbar and including fixed with 25mm x 6 mm mild steel clamp of suitable length complete all as specified and as directed.

Supply and fixing of MCB SP of rating 6 to 32 Amps 240 V complete all as specified and as directed.

Supply and fixing MCB DP 40 to 63 amps 415 volts 10KA breaking capacity.

Material and labour for Earthing as in repair complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm thick, burried directly and preferably vertically in ground, earth pit not less than 2.25 Mtr deep below ground level with top edge of the plate not less than 1.5 Mtr below ground level connetced with earthing wire 4.0mm dia as earthing lead by means of nuts, bolts, check nuts and washers made of galvanised iron or steel earthing lead to be protected by galvanised iron pipe 15 mm bore (medium grade) and other end connected to earthing test point or lightening arrestor or main controlling switch as directed including providing funnel with 20mm bore galvanised iron pipe (light grade), wire mesh, charcoal or coke and common salt in alternate layer of 15cm (compacted thickness) all round the earth electrode, concrete earth pit in PCC (1:3:6) type C-1 (with 20mm graded aggregate), 50mm thick precast RCC (1:2:4) cover slab (re-inforced with 8mm dia TMT bar @ 15 cm C/C bothways and suitable handle made of 10mm dia) including necessary earth work in excavation, returning filling and removal of surplus earth upto a distance not exceeding 50 Mtr etc all as shown on electrical plate No. 5 of MES Schedule Part-I complete including testing on completion. On testing after completion if the desired earth resistance is not obtained the earthing will be redone at no extra cost.

Note: Schedule of credit (SCHEDULE OF CREDIT) amount of Rs ₹ ___________ mentioned on Page No ____ shall be deducted from the total quoted amount of BOQ.

RAJIB GOSWAMI ENTERPRISE

M/S DHAR AND DHAR

M/S GOPAL ROY AND CO