GE/863/EWS-T-21 OF 2021-22

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavation over area not exceeding 1.5M deep and getting out in hard/dense soil complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil complete all as specified and directed.

Excavating in Hard / dense soil in post holes (or similar holes ) each not exceeding 0.5 cu. m. getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus spoil to a distance n. exc 50 metre and making good surface complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc. 25 cm thick in each layer as in soil complete all as specified and directed.

Removing of excavated Soil/material to distance of n exc 50m and depositing where directed at a level n.exc 1.50m above the starting point complete all as specified and directed.

Removing excavated materials(soils) to a distance exc 250m but not exc 500 M where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling in mass concrete etc complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in foundation, filling in mass concrete etc complete all as specified and directed.

M&L for PCC 1:2:4 type B-2 using 40mm graded stone aggregate as in foundation, filling in mass concrete etc complete all as specified and directed.

M & L for stone Walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 etc complete all as specified and directed.

M &L for pre-cast cement concrete type C1 1:3:6 using 20mm graded stone aggregate as in block masonry with solid blocks, exc 10cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for 40 mm thick Cement Concrete M-15 Nominal Mix (using 12.5 mm graded stone aggregate) as in damp proof course (DPC) to horizontal or vertical surfaces including necessary form work and mixing of water proofing compound as per manufacturer’s instructions complete all as specified and directed. NOTE: - water proofing compound will be measured and paid separately as 'Supply only' under respective item.

Supply only Integral water proofing compound (WPC) complete all as specified and directed.

Extra over to stone walling for hammer dressing to face stones and dressing of the face beds & joints as specified of squared rubble walling regular coursed, Jodhpur type, with maximum depression of face from straight edge held against the dressed surface n.exc. 20mm. complete all as specified and directed.

M&L for rendering 15 mm thick on brick or concrete surface of walls in cement mortar 1:4 finished even & smooth without extra cement including mixing only water proofing compound as per manufacturer's instruction complete all as specified and directed. NOTE: - water proofing compound shall be measured and paid separately as 'Supply only' under respective item.

M&L for rendering 10 mm thick on brick or concrete surface of walls in cement mortar 1:4 finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick on brick or concrete surface of walls in cement mortar 1:6 finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 15 mm thick on brick or concrete surface of walls in cement mortar 1:4 finished even & smooth without using extra cement complete all as specified and directed.

M&L for rendering 5 mm thick on concrete surface of walls in cement mortar 1:3 finished even & smooth without using extra cement complete all as specified and directed.

M & L for providing pre-cast cement concrete landing, cover slabs (for man holes etc), chullah hoods, chajjas, water troughs, mangers, shelves and similar items with plain faces in cement concrete 1:2:4 type B-1, using 20 mm graded stone aggregate and setting in cement mortar 1:6 including necessary formwork complete all as specified and directed.

M & L for preparing newly plastered or previously untreated walls surfaces and applying two coats of cement base paint over one coat of primer complete all as specified and directed.

M & L for preparation of new plastered surface of wall and applying two coats of distemper oil emulsion over a coat of chalk whiting as a preparatory to distempering complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63 mm of broken boulder, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for Hardcore of gauge n exc. 63 mm of broken bricks, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 75mm thick P.C.C 1:4:8 type D-2 in sub base / hard standing of floor finished even and smooth without using extra cement complete all as specified and directed .

M&L for 25 mm thick PCC 1:2:4 type B1, using 20 mm graded stone aggregate as in flooring including finishing cement concrete in rough surface without using extra cement complete all as specified and directed.

M&L for Glass dividing strips, 38mm wide and 3 mm thick and erected in position complete all as specified and directed.

M & L for Chequered cement concrete tiles 20cm x 20cm x 25 mm thick, Set jointed and pointed in neat cement slurry with grey cement & pigment laid over and including 15 mm thick screed bed in CM 1:6 as in floor etc. set and jointed in neat cement slurry and pointed in white or Coloured cement to match complete all as specified and directed.

M & L for machine cut kota stone slab flooring 20 to 25 mm thick over and including 20 mm thick screed bed laid in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and mirror polishing complete all as specified and directed.

M&L for machine cut kota stone slab 20-25 mm thick laid and jointed with grey cement slurry mixed with pigment to match shade of the slab including cutting, waste, rubbing and polishing (Granite finish) as in skirting/dado over and including 10mm thick plaster in cement mortar (1:4) on brick work or concrete surfaces, including cutting, rubbing and mirror polishing (Granite finish) complete all as specified and as directed.

M&L for Plain Cement Concrete Type C1 1:3:6 (using 20 mm graded stone aggregate) cast in situ in lintels up to 1.5 M span, cills and other similar bands, plinth courses, parapets, copings, bed plates and the like including weathering, slightly rounded or chamfered angles and throating as directed including use and waste of form work complete all as specified and as directed.

M & L for mild steel rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete incl cutting to reqd length, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts etc Fe-410 (Gde E-250) B quality complete all as specified and as directed.

S&F rolled Mild steel plates plain square cut or notched (ordinary and counter sunk) forming holes, without any attachment.(Fe-410-W(Gde E-250)Quality-A) complete all as specified and directed.

S & F structural steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes for vertical post, purlins and rafter confirming to IS:1161- 1979 grade St-240, complete all as specified and as directed.

S & F structural steel work in Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to I.S.1161- 1979, Fe 410 -W (GdeE- 250) quality 'A' complete all as specified and as directed .

S&F mild steel Framed work as in doors or gates of angle or other section with gusset plates, rails,braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering,running rails and guides) and hanging; also fastening and fixing complete all as specified and directed

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and directed.

S&F Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

M & L for preparation of new or previously untreated surfaces of steel of any description , over 10 cm in width or girth not otherwise described applying two coats of synthetic enamel paint (ordinary tint) over a coat of red oxide primer complete all as specified and directed.

M & L for preparation of new wooden surface any description not otherwise described and exc 10cm width or girth applying two coats of synthetic enamel paint over a coat of prink primer complete all as specified and directed.

M&L for Non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding exc. 0.06 sqm but n.exc. 0.11 sqm, in floors etc. set over and including 15 mm thick screed bed in cm (1:6) and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

M&L for coloured Glazed ceramic tiles in vertical surfaces 350 x 250 x7 mm/ 450 x 350 x7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match laid over & including rendering 10mm thick in cement mortar 1:4 on stone masonry surfaces or surfaces other than fair face of brick work to receive glazed tiles/granite complete all as specified and directed.

M&L for Reinforced cement concrete M-25 design mix (20 mm graded stone aggregate) as in Beams, cantilevers, bressummers complete all as specified and directed.

M&L Reinforced cement concrete M-25 design mix (20 mm graded stone aggregate) as in Chhaja complete all as specified and directed.

M & L for use & waste of formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, bands, cantilevers, shelves including supports, overhangs etc. also splayes between floors and beams in rough finished flat surface of concrete complete all as specified and directed.

M & L for use and waste of formwork to chullah hoods, chajjas, troughs and similar items including edges in rough finished flat surface of concrete complete all as specified and directed.

M & L for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M & L for mild steel TMT bars 5 mm dia and over upto and including 10 mm dia as in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

S & F second class hard wood Plain, solid, straight, chowkats and frames, wrought, framed rebated on the solid, rounded or chamferred, put together with glue pinned at joints. complete all as specified and directed .

M&L for Providing cement concrete type C-0 1:3:6 (12.5 mm graded stone agg) as in filling in pressed steel chowkhats complete all as specified & directed.

S & F 35 mm thick factory made Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified & directed.

S & F 35 mm thick factory made second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc., sizes of members of shutters as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and directed.

S & F 30 mm thick factory made Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass etc. as specified in SSR Pt I Section 8, clause 8.24 (a) complete all as specified and directed.

S&F factory made solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube in opening as per specification and drawing as per SSR Part-II 2020 complete all as specified and directed.

S&F factory made soilid panel PVC Door shutter 30mm thick (Style), consisting of frame made out MS frame shall be covered with heat moulded plain coloured PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail, & bottom rail; Panneling of plain colour PVC sheet to be fitted in the M.S. frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification and drawing as per SSR Part-II 2020 complete all as specified and directed.

S&F MS framed work such as in grills, gratings, etc with ends of bars shouldered or riveted framed guard bars and similar work confirming to Fe-290 Gde E- 165 complete all as specified and directed.

S & F plain sheet glass of 3 mm thick in Squares not exceeding 0.50 Sqm in each pane with oil putty and clips complete all as specified and directed.

S&F150 mm long barrel tower bolt aluminum anodized extruded section fixed with cadmium plated screws complete all as specified and directed.

S&F 150 mm Aluminium handles, cast type, anodized complete all as specified and directed.

S & F 250 mm long Aluminium alloy, anodized, sliding door bolt with hasp staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of truded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S & F Galvanized mild steel wire cloth, 0.63 mm dia of wire and average width of aperture 1.18 mm and fixed with tinned stacks, or galvanized wire staples complete all as specified and directed.

S&F 100mm butt hinges, extruded brass, with mild steel hinge pin, bright polished type B-11 complete all as specified and directed.

S&F anodised aluminium snap grid frame work for false ceiling of size of grid 605 x 605 mm including hangers, cleats, fasteners and hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceilling cleats made out of GI flat 40 X 3 mm size 60 mm long complete all as specified and directed.

M&L for false ceiling with gypsum board, perforated type, factory made matt finish surface / pre-painted surface, 600 x 600 mm in size and 12 to 15 mm thick on exisiting aluminium snap grids 605 X 605 mm as in ceiling complete all as specified and directed.

M&L 75mm thick Cement concrete type C2, 1:3:6 (using 40 mm graded stone aggregate) as in plinth protections, finished even and smooth without using extra cement complete all as specified and directed.

S&F 140mm Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F 1000 ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) double layered duly provided with necessary fittings/fixtures for connecting inlet, outlet, washout and overflow pipes, hoisted including 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 15mm-142gms/ 20 mm - 210 gms / 25mm - 455 gms / 40mm - 690gms) complete all as specified and directed.

S&F 15 mm dia stop cock of copper alloy screwed down high presser with crutch or butter fly handle on both ends for iron pipe or for union complete all as specified and directed.

S&F 20 mm dia stop cock of copper alloy screwed down high presser with crutch or butter fly handle on both ends for iron pipe or for union complete all as directed.

S & F 15 mm bore Fancy type Chromium plated bib taps, cast copper alloy, with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F 15mm bore pillar tap, cast copper alloy, with capstan heads, fancy type, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

S&F PVC Connections 15mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F vitreous china wash hand basin, white flat back size 550x400mm complete including necessary cutting for and pinning in ends of brackets ) including brackets and 750mm long PVC waste pipe 32mm bore & waste coupling 32mm dia of PTMT (half or full threaded) complete all as specified and directed.

S & F 15mm bore tubes 'medium grade' galvanised, with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and directed.

S & F 110 mm dia bore PVC (SWR) pipes single socketed , in any length with rubber ring joints , laid in tenches or in floors complete all as specified and directed .

S & F for Vitreous China squatting pan (Orissa pattern) size 580mm X 440mm, white with integral foot rests, any pattern including provision of cement concrete bedding (excluding flushing cistern and flush pipe) complete all as specified and directed.

S&F PVC (SWR) floor trap 75 mm dia of outlet , plain with grating including jointing with solvent cement complete all as specified and directed.

S & F Rolled Mild Steel as in staging for water tanks, compound girders and stanchions, lattice girders, aerial masts, and the like including caps, bases, splices etc. built up from two or more beam or channel sections or angles with plates, including all lattice bars, stiffeners, gusset plates, etc confirming to Fe 410-W (Gde-E-250) quality A complete all as specified and directed.

M & L for 150mm bore, reinforced cement concrete pipe class NP-3 laid and jointed with collars including fittings of same grade in trenches at any depth including jointing and testing, complete all as specified and directed. Note : (i) Excavation and earth work and concrete for bed and haunching of pipe shall be measured and paid separately.

M&L for Plain cement concrete (1:4:8) , type D-2, using 40mm grade stone aggregate as in concrete bed to drain pipes laid to falls in trenches in any depth including packing under and haunching against the sides of pipes for 150mm bore pipes with concrete after the pipes are laid and tested, complete all as specified and directed.

Provn of septic tank ( 25 users) including excavation, returnning filling and removing of surplus soils in hard/dense soil/ soft rock , PCC floor in (1:2:4) type B-1 (using 20 mm graded stone agregrate), RR masonary wall in CM 1:4, RCC work shall be in ( 1:2:4 ) type B-1 ( using 20 mm graded stone aggregate) as in slab, baffle wall, MH covers, etc including necessary form work & Reinforcement as shown in drgs , plastering to walls 15 mm thick in CM 1:3, finished even and smooth using WPC @ 3% by weight of cement or as per manufacturer's insturctions, complete all as specified and shown on drg No GE/863/EWS/TD-7/2011 sheet No 1/2 to 2/2 dated 12 Dec 2011.

M&L for soakage well of size 1.8 mtr dia and 3.00 metre deep including excavation in hard/ dense soil / soft rock, removing excavated soil out side defence land, Foundation in PCC 1:4:8 , PCC solid block Masonry work type C1 ( 1:3:6) set in CM 1:4 and provn of loose filling with Brick bats, cover slab with RCC (1:2:4) type B-1 (using 20mm graded stone agg) including necessary form work and reinforcement complete all as specified and as shown in drgs No GE/863/EWS/TD-10/2013 sheet 1/1 dated 16 Apr 2013. NOTE: (i) Dia of soakage well shall be 1800 mm in lieu of 2400 mm as shown in drawing. (ii) PCC solid block honey comb Masonry and PCC solid block masonary , (1:3:6), type C1 set in CM 1:4 shall be used in lieu of honey comb brick wall and solid brick mansonary as shown in drawing.

Material & labour for point wiring with copper multi-stranded conductor cable FRLS, PVC insulated sheathed of cross sectional area 1.5 Sqmm (nominal area) in and including concealed PVC conduit medium grade, fixed with plastic laminated bakelite sheet top cover MS pressed steel sunken box and machine brass screws and washers for mounting switch, socket , fan regulator etc for one light/fan point controlled by one switch complete including 1.5 Sqmm PVC FRLS insulated stranded copper conductor earth wire complete all as specified and directed.

All as per Srl item No 85 here-in-before but controlled with one 3 pin socket outlet 5 Amp on the same board with other switches with cables 1.5 Sqmm .

All as per Srl item No 85 here-in-before but controlled with one 3 pin socket outlet 5 Amp,independent board with cable 1.50 Sqmm size including provision of 1.5 sqmm single core multistranded FRLS PVC insulated multistranded copper conductor as earth conducting conductor.

All as per Srl item No 85 here-in-before but controlled with one 3 pin socket outlet 15 Amp,independent board with cable 2.50 Sqmm size including provision of 1.5 sqmm single core multistranded PVC FRLS insulated multistranded copper conductor as earth conducting conductor.

Supply and fixing switch piano type 15 Amp, 230 Volt, flush button single pole one way complete all as specified and directed .

Supply and fixing socket outlet 6 pin 15 Amp 2-in-one 230 Volt flush type complete all as specified and directed .

Supply and fixing socket outlet 6 pin 5 Amp 2-in-one 230 Volt flush type complete all as specified and directed .

Supply and fixing switch piano type 5 Amp, 230 Volt, flush button single pole one way complete all as specified and directed .

M&L for Ceiling rose, 3 terminal with ISI mark complete all as specified and directed.

Supply and fixing surface & wall mounted LED 20W tube light fitting, 220 V, AC, decorative box type with driver, holder including LED tube rod connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with all accessories complete all as specified and directed.

Supply and fixing surface & wall mounted LED 18W tube light fitting, 220 V, AC, decorative box type with driver, holder including LED tube rod connecting up with three core flexible copper conductor cable of suitable size from ceiling rose with all accessories complete all as specified and directed.

M & L for Lamp holder, PVC/Polycarbonate type with back plate suitable for batten / angle fittings complete all as specified and directed.

Supply and fixing LED lamp 9W system lumen (NOM) 600 with all accessories complete all as specified and directed.

Supply & Fixing flame proof LED bulk head luminaires 1x9W/1x10W including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size with all accessories complete all as specified and directed.

M&L for House service bracket (hook type) complete with 3.0 mtr long G.I pipe, 40mm dia, Med grade, two nos 90 degree bends, MS hook and stay or guy complete all as specified and directed.

S&F exhaust fan, steel body , heavy duty, AC, Single Phase 300mm sweep, with louvres complete all as specified and directed .

Supply and fix Sheet metal enclosure for DBs 4 way, double door for DB's single pole & neutral, 240 Volt, with 200 Amps rates bus bar complete all as specified and directed.

Supply and fixing of miniature circuit breaker (MCB) SPN 40 Amp rating 240V, 10KA 'C' curve, in the MCB DB complete with connection testing and commissioning complete all as specified and directed .

Supply and fixing of miniature circuit breaker (MCB) SPN 32 Amp rating 240V, 10KA 'C' curve, in the MCB DB complete with connection testing and commissioning complete all as specified and directed .

Supply and fixing in replacement of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

Supply and fixing 1100 Volts grade heavy duty cable PVC insulated aluminium stranded conductor served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hangers not more than 1 meter apart including 4mm dia suspension wire one twin core cable flat or circular of size 10 Sqmm complete all as specified and directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part I,connected to earthing test point all as specified or indicated including testing on completion ,necessary excavation, earthwork, PCC works in 1:2:4 type B-1, form work and CI earth pit cover with watering pipe 20 mm dia GI Pipe medium grade, funnel with wire mesh and lugs, GI Pipe of 15 mm dia of light grade for protection of earth wire complete all as specified and directed.

S&F for earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanized iron or steel wire, complete all as specified and directed.

Supply and fixing electric water heater,storage type, rust proof, powder coated steel body ,with copper inner tank and heating element upto 2 KW ,capacity 25 litre, BEE 5 Star rated, electric operated 230 V, Single Phase complete with all accessories such as safety valve, thermostate, NRV, connection piece, multifunctional safety valve, automatic thermal cut out, fusible plug, anti vacum sys, built in presser release valve,thermostat, indicator lamps and all safety devices including provn of grouting bolts in walls including CP brass pillar cock 15 mm ,PVC connection 600 mm with not & Bolts for hot water etc and making good to disturbed surfaces complete all as specified and directed .

S & F GI tubing medium grade of size 25 mm bore dia including all fitting such as bend, Tee, union, socket etc laid in trenches complete all as specified and directed.

S & F GI tubing medium grade of size 20 mm bore dia including all fitting such as bend, Tee, union, socket etc laid in trenches complete all as specified and directed.

S & F GI tubing medium grade of size 50 mm bore dia including all fitting such as bend, Tee, union, socket etc laid in trenches, fixed to wall, ceiling or laid in floors complete all as specified and directed.

S&F 25 mm dia Gun-metal, globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S&F 20 mm dia globe or gate valves with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

S & F 20mm bore ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

Supply & laying cable XLPE insulated IS 7098 (Part-I)-1988 marked, screened, PVC sheathed, armoured electric power cable (heavy duty) with aluminium conductor for working voltage upto and including 1100 volts, cross sectional area of cable 10 sq mm 2.0 core with aluminium conductor laid in trenches/fixed on pole/wall/passed through pipe /cutting of road with making good wherever required as per site including jointing and testing complete all as specified & directed .

M&L for Sand cushioning for under ground cables complete all as specified and directed.

Supply and lay well burnt class ‘B’ bricks as mechanical protection to under ground cables laying with length of the bricks equal to the width of the trench complete all as specified and directed.

M/S SHIV NATH ENTERPRISES

M/S Gopal Singh