eNIQ No. - 02 /WBPWD/AE/AHESD of 2023-24

Amount

Supply & Delivery of LT Cubical type floor mounted panel board with Multi Compartment : one for incoming, one for busbar and one for outgoing MCCBs made with 14 SWG CRCA Sheet. The panel board should have proper cable alley both side with cable entry at bottom and outgoing from top with Seimens type locking arrangement and detachable Gland Plate. The board should be painted with powder coated paint. The Panel board consisting the following : Incoming : (A) 415V FP 400A MCCB with spreader terminal & extended rotary handle (Make : L&T) - 1 No. Busbar : (A) 500V Gr. 630A 4 Nos. tinned Cu Bar for Phases & Neutral - 1 Set Outgoing : (A) 415V FP 125A MCCB with spreader terminal & extended rotary handle (Make : L&T) - 4 Nos. Metering : (A) 0-630A Digital Ammeter - 1 Nos. (B) 0-500V Digital Voltmeter - 1 Nos. (C) CT of ratio 400/5A - 3 Nos. (D) LED Indicating lamps with control fuse - 3 Nos. (E) 6A TP MCB - 1 No. (F) Danger Board - 1 No. All inter connections form incoming to busbar and busber to outgoings are to be connected with suitable size of Cu bars & wire as per direction of EIC (Including all Taxes & duties)

S&F 3" x 1½" MS iron channel with MS Clamp Stopper grouted on floor/wall to support the LT Panel incl. nut, bolt & washer as per direction of EIC

Instn. of the service panel with all necy. arrangements as per direction of EIC (Including all Taxes & duties)

Supply, fabrication and eraction of supporting cable ladder post using 80 mm GI pipe of 6 mtr. long incl. 1.5 mtr. below ground level with base plate and fixing plate on the top of the post made of 250x250x8mm thick with necessary holes and nut bolt washer for supporting the ladder arrangement, having 450x450x200 mm thick CC (4:2:1) base block incl. CC (6:3:1) muffing 030 mts dia and 0.30 mts above ground level and 3mm thick neat cemented finish as per direction of EIC (Including all Taxes & duties)

Supply,Fabricating and fixing of special type cable ladder arrangement having width 350 mm made of 2 nos. 50x6 MS angle iron and 50x6 strip @ 200mm for holding the two adjacent angles maintaing sufficient spacing between them and providing necessary arrangement for fixing and supporting cable tray on the post and wall brackets as per direction of EIC (Including all Taxes & duties)

S&F specially fabricated "L" shaped 50x50x6 mm MS angle bracket for supporting the cable tray on wall. the length of bracket 600 x 450 mm having 600mm length having drilled holes & fustern on wall, strong enough to withstand the load of total cable tray setup having cables laid through the tray and providing cross arm as per direction of EIC (Including all Taxes & duties)

Supply & fixing of 300X50X1.25mm (18SWG) perforated GI cable tray with perforation not more than 17.5% on the MS angle ladder incl S&F necessary Stainless Steel bolts & nuts,.

PWD Sche. Item: D-14/34(a): Supply & fixing of perforated GI cable tray with perforation not more than 17.5% suspended from ceiling incl S&F G.I. connector, 6mm dia MS suspender bolts & nuts, steel fastener etc as required of the following size incl. Al painting of MS support. With 25x25x3mm angle iron support 300X50X1.25mm (18SWG)

PWD Sche. Item: D-15/34(b): Supply & fixing of 300X50X1.25mm (18SWG) perforated GI cable tray bend with perforation not more than 17.5% suspended from ceiling with two nos., suspenders & 25X25X3mm angle iron for supporting the bend incl. S&F G.I. connector, 6mm dia MS suspender, bolts & nuts, steel festener etc as required of the following size incl. Al painting of MS support.

Dismantling of plastered wall aproximately 400 mm wide and at least 100 mm high for the cable tray work incl. cutting rods & cement concrete works & removing rubbish, earth etc. from the working site & deposit the same beyond the compound & cleaning the site in all respect as per direction of EIC

Supplying and delivery of 4 core x 300 sq. mm. 1.1kV grade Aluminium Armoured Power Cable. (Make: Havells)

PWD Sche. Item: F-3/4(c): Laying of one cable upto 300 sqmm through existing covered masonry trnch incl. taking out RC covers, setting them in order, mending good the damages filling the trench with fine dry sand incl. supplying sand

PWD Sche. Item: F-4/7: Supplying and fixing of 4 core x 300 sq. mm. compression type gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE/PVC armoured cables.

PWD Sche. Item: F-5/8(a): Finishing of the following XLPE/PVC insulated armoured cable ends by soldering with cable sockets, soldering materials, tapes etc. and making connection to switch, BDB and BBC etc. 4 core x 300 sq. mm..

S. A. ENTERPRISE

JAYBEECO