Construction of 0.70 MT (Capacity) Micro Compost Centre(MCC),Shredding unitand Storage shed at Kulivayal of Cherangode Panchayat

Construction of 0.70 MT (Capacity) Micro Compost Centre(MCC),Shredding unitand Storage shed at Kulivayal of Cherangode Panchayat IN GUDALUR BLOCK, THE NILGIRIS DISTRICT

Earth work excavation and depositing on bank within initial lead and lift in classass of soil etc., complete as per (SS 20B) for foundation

Providing of Granular Sub base using Grade I materials of table 400 -1 of Morth with minimum CBR 30 spreading in uniform layers with motor grader on prepared surface, mix in by palce method at OMC and compacting with Vibratory Roller to achieve the desired density including all labourcharges etc, complete as per technical specification and as directed by the departmental officers.

Supplying and filling in foundation and basement with filling sand in layers of not more than 15cm thick well rammed watered and compacted etc., complete complying with standard specification.

Cement concrete 1:4:8 mix (One cement four sand and eight hard broken stone) using 40mm gauge hard broken granite stone jelly for foundation including watering wherever necessary and laid in layers not more than 15cm thick compacting etc. complete complyin

Providing granolithic floor finish of 25mm thick with plain cement concrete 1:2:4 (One Cement, Two sand and Four aggregate) using 10 to 12mm gauge hard broken stone jelly including laying, finishing and the top rubbed smooth with power trawl, thread lining, curing etc. complete complying with standard specification and as directed by the departmental officers.

Supply and errecting centering with necessary supports including all labour charges etc., complete complying with standard specification.

Reinforced cement concrete 1:1.5:3 (One cement 1.5 sand Three hand broken stone) suing 20mm gauge hand broken hard granite stone jelly for all RCC items of works excluding cost of reinforcement and fabricating charges centering and shuttering but including curing and providing fixtures like fan clamps in the RCC floor or Roof Slabs wherever necessary and bearing surfaces of walls sides and bottom of the slabs beams etc shall be finished smooth with cement mortar 1:3 (one cement three sand) 12mm thick and with Kraft paper without claiming extra etc. as directed by the departmental Officers complete complying with standard specification. The rate is to include vibration charges

Supply and fabrication of steel including all labour charges etc complete complaying with standard specification

Brick Work in cement mortar 1:5 mix using country bricks of size (8 ¾ x 4 3/8 x 2 3/4) including cost & conveyance of all materials to site

Brick Partition walls in CM 1:3 (one cement & three sand) using III class Country bricks of size 83/4" X4 using hoop iron reinforcement 2 Nos of 6mm dia M.S.rod at every three alternate layers and the cost shall inclusive of iron reinforcement, Brick work etc, complete as per standard specification

Plastering with cement mortar 1:5 12mm thick including cost & conveyance of all materials to work site including cement which will be supplied by the department from the departmental section store and the cost for the same will be recovered

Plastering with cement mortar 1:3 10mm thick including cost & conveyance of all materials to work site including cement which will be supplied by the department from the departmental section store and the cost for the same will be recovered

Supply and fixing of PVC Solid Doors using 19gauge 19mm MS Sq,tubes for styles and frames, 15mm MS Sq.tubes for to, Lock and bottom rails. The Steel Tubes shall be covered with 5mm thick Solid PVC sheets. Shutter using 5mm thick solid PVC sheets for panelling shall rigidly fixed in position including furniture and fittings. The over all size of styles shall be 50mm X 30mm. The over all size of top rail, Lock rail and bottom rail shall be 75mm X 30mm. The over all size of frames shall be 50mm X 45mm with suitable tabate for housing the

Supplying and fixing in position of alulminium anodised colour matt finish Louvered Ventilator. The outer frame will be 62x38x2mm @ 1.17 Kg / m and the louvers with moving arrangements will be made with Alu. Channel of size 60x30x4 mm @ 1.27 kg /m with necessary glass pans for louvers 4mm thick Al. Clips, including all materials, labour & power consumption charges required for fabrication if necessary chipping dismantling making holes in RCC columns, beams or masonry wherever necessary with power drill to the extent required and make good to the original conditions after fixing etc., complete. The Aluminium sirface is to be anodised with matt finish under electrically controlled condition in accordance with ISI specification 1868/1962 of anodic film thickness of not less than15 microns (fifteen) for all sections.

Supply and fixing of M.S Grills with Doors and Windows with one coat of Red oxide with Primer including all costs such as welding, grinding and fabrication charges, cost and conveyance of all materials to site etc,complete as per standard specification.

Painting 2 coats with approved cement paint over cement plastered wall surface, ceiling and other new surface and including cleaning, preparing the surface and curing etc., complete.

Paving the floor with best quality Vertified Tiles of size 600 x 600 x 8mm of approved color, shade and quality laid in cement mortar 1:3 (one cement and three sand) 20mm thick in all floors and the top pointed with the white cement mixed same color pigments etc., complete complying with standard specification

Dadoodling the walls with colored glazed tiles approved size, quality and color set in CM 1:2 - 10 mm thick. And pointed with suitable cement including finishing the joint and pointing flesh with walls and tile surface in all floors at the rate of 0.40 Kg /Sqm etc. complete. Basic cost-Rs.318/sq.m

Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc, complete as per standard specification

Fabricating supplying and fixing of pre painted galvanized iron sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47 mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

Supply and fixing of RCC Rings(0.90m Dia,0.30M Hight)

Supply and fixing of RCC Preast slab(0.90m Dia)

Supplying and fixing in position Indian water closet of size580 X 440mm, white glazed earthen ware of approved quality with 'P' trap or 'S' trap confirming to IS:2556 - Part XII with sand cushion and forming flooring alround the closet using 40mm broken brick jelly in lime concrete 1:2:5 ( one part of lime, two parts of sand and five parts of brick jelly) 100mm thick and finishing the top to required slope and including giving necessary connection to cast iron soil pipes/ PVC pipes by dismandling brick masonry, reinforced cement concrete roof/floor slab and making good the disturbed portion to original condition without leakage etc., complete complying with standard specifications and as directed by the departmental officers.

Supplying laying and jointing P.V.C pipes (6Kg/SqCm) of approved quality and best variety conforming to I.S.S & with I.S.I mark, of the following sizes including cutting , Fixing to PVC specials using Adhesive but excluding cost of such specials and fixing to wall with necessary teak - Wood Plugs,PVC Clamps and screws,making holes on the wall or drilling holes in roof and making good the dismantled portions to original condition with necessary brick work and plastering wherever necessary with necessary scaffolding charges.(75 mm Dia PVC Pipe)

Supplying laying and jointing G.I. Pipes of approved quality and best varity of B Class pipe of the following sizes including fixing G.I specials but excluding cost of such specials cutting threading of pipes and fixing to wall with necessary teak wood plugs, clamps and screws masking holes on the wall or drilling holes in roof and making good the dismandled portions to original conditions with necessary brick work and concrete and plastering where ever necessary with necessary scafolding charges. The pipes are to be painted with two coats of good variety and best approved quality of synthetic enamel paint over a priming coat of red-oxide primer etc., complete.(20 MM dia GI Pipe)

Supply and fixing of following Plumbing G.I.materials(20mm dia GI Coupling)

20mm dia GI Elbow

20mm dia Steel tap

Supplying and fixing UPVC Pipe and specials(25mm dia UPVC Pipe)

25mm dia UPVC Connector

25mm dia UPVC Union

25mm dia UPVC Coupling

25mm dia UPVC Bend

Supplying and fixing in position best quality P.V.C specials, complying with standard specifications.

Supplying and fixing in position best quality P.V.C soil/ waste pipes (6KSC) of various sizes having ISI mark and providing leakproof joints including fixing to the wall with P.V.C/ M.S clamps etc., and making connection to all sanitary fittings, dismandling masonry/R.C.C. works wherever necessary and making good the dismandled portion to the original condition, complying with standard specifications.(110mm dia PVC 6KSC Pipe)

Supply and delivery of 1000 lit capacity and fixing of HDPE tank as per IS 12701/1996 including loading, unloading, transportation and labour charges for fixing of the GI pipes and specials for pipe connection works including cutting, threading and fixing charges etc.,complete as per standard specification.

Wiring with 2 x 1.5 sqmm (22/0.3) PVC insulated unsheathed Sc Cu.Conductor of 1100V grade in suitable PVCrigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A F.T. switch inflush with wall,covered with hylem sheet of 3mm thick with painting of suitable colour for open PVC light point(SD 21)

Supply and run of 4 of 6 sqmm (84/0.3) PVC insulated SC unsheathed Cu.Conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 14 SWG TC wire and making good of the concealed portion with suitable colour. SD 62

Supply and fixing of single box type 4'36 W flu fitting complete with Electronic ballast and condensor with TW round blocks on wall or ceiling with flu tube with PVC unsheathed Copper leads from terminals to the fitting SD 87

Earthing as per P.W.D. standard with an earth electrode of 2Mtr. Class 'B' GI pipe of dia not less than 32mm complete with necessary masonry work.SD 234

Supply and run of 2 x 1.5 sq.mm. (22 / 0.3) PVC insulated SC unsheathed copper conductor of 1100V grade in25mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron upright and end supports for mains(SD 69)

Wiring with 2 x 4sqmm (56 /0.3 ) PVC insulated single core unsheathed copper conductor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories inflush with wall with 150 x 100 x 113 mm TW switch box with 3mm hylum sheet cover for 15A 3 pin non inter locking CS plug with continuous earth wire connection of 14 SWG TC wire for Open PVC power plug point.SD 41

Supply and fixing of TNEB meter board suitable for 32A three phase service connection with 3 Nos. 32A fuse unit(500V) 32A neutral link and earth link (1" x 1/8" copper flat) on TW plank of size 600mm x 450mm x 19mm withsupporting TW reepers of 1" thick an either side with painting with suitable bolt and nuts for fixing the TW plank onwall with earth connection and inter connection with 7/20 PVC insulated copper wire from EB meter to fuse unit(SD 129)

Supply and fixing of Plywood sheet with GI Sheet

Manufacture and Supply of Shredder machine only for segregation garbage should have using MS plate 20mm, 10mm, 3mm & channel 75 * 40 L Angle 40 * 60 & Shaft 60mm dia capacity of 1 MT to 1.5MT / Hr with single shaft cutter, steel grade blade 10 HP Motor, size 600mm, 800mm, chute - yes (Feeding & Discharge) with manual feeding, Electrical - 10 HP starter only without cable, total machine height is 2000mm & width 1200mm, feeding conveyor - no (Manual).

Supply and Fixing of sanitary napkin buring machne of size 600mm X 600mm X 900mm With MS Legs Whole system made up of mild stell material with LCD Display with temperature and time indication 'PUF' Insulation, easy removing ash collecting tray ensures cleanliness, bigdoor opens makes it convinient to load used napkins, heater of High power of 3000 W Makes the temperatre rise quickly and improve the efficiencly, Computerised programmed control panel of 600 to 800 Celsius gives long life for heaters and reduce the electircity bill including all cost of labour, treansportation charges, fixing of machine in suitableplace with directed by the departmental officers etc., complete.

Supply, fixing and commissioning of Belt conveyor length of 6 mtrs and breath of 0.50 Metre wide for organic waste shorting and conveyor structure should made with M.S. Heavy Tubes, M.S. Channels with Gear Motor of 2HP / 50 rpm / 440V / chain drive motor rollers with heavy rollers: 2 Nos and shaft should be of ISI standard and Bearings, MOC - EN8 make should be of "HAVELLS' / MARATHON and the total setup should covered with FRP. The conveyor should be with branded starter, motor should be heavy duty performance, FRP Hopper with necessary safety guard facilities and all materials should be got approved by the corporation Engineers before fixing in position including cost of materials and labour charges etc. complete.

Provision for Supply and Fixing of Weld Mesh

Flying Insect Killer UV Tube Catcher Machine

Flying Insect Killer UV Tube Catcher Machine

Provision for EB Service connection

Earth work excavation and depositing on bank within initial lead and lift in classass of soil etc., complete as per (SS 20B) for foundation

Cement concrete 1:4:8 mix (One cement four sand and eight hard broken stone) using 40mm gauge hard broken granite stone jelly for foundation including watering wherever necessary and laid in layers not more than 15cm thick compacting etc. complete complyin

Supply and errecting centering with necessary supports including all labour charges etc., complete complying with standard specification.

Cement concrete 1:3:6 mix (One cement three sand and six hard broken stone) using 40mm gauge hard broken granite stone jelly for foundation including watering wherever necessary and laid in layers not more than 15cm thick compacting etc. complete complyin

Brick Work in cement mortar 1:5 mix using country bricks of size (8 ¾ x 4 3/8 x 2 3/4) including cost & conveyance of all materials to site

Supplying and fixing of GI Square tube including cost and conveyance and all labour charges etc complete.(Struss)

Supplying and fixing of GI Square tube including cost and conveyance and all labour charges etc complete.(Purlin)

Supplying and fixing colour galvalume sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Supply and fixing of GI corrugated 0.80 mm thick including cost of " J " bolts and bitumen washer etc.complete.

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Providing granolethic floor finish in cement concrete 1:2:4 mix using 10-12mm,ISS metal to 25mm thick curing etc., complete complying with standard specification as directed by the departmental officers.

Distembering with two coats of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Exterior Emulson with two coats of approved colour and quality over one coat of white cement primer including cleaning and preparing the wall surface and brushes, sand paper, scaffolding charges

Painting New Iron works such as steel doors, windows, ventilator, window bars, balusters etc., with two coats of approved quality and colour of synthetic enamel paint over the existing red oxide priming coat etc complete complying with standard specifications. (The make quality and colour of paint should be got approved by the Executive Engineer before use on work).

Towards the supply of Steel Doors(1.20X2.10 M)

Towards the supply of Steel Doors(0.90X1.20 M)

Towards the supply of GI Pipe(50mm Dia)

Earth work excavation and depositing on bank within initial lead and lift in classass of soil etc., complete as per (SS 20B) for foundation

Supply and fixing of GI Pipe(50mm Dia)

Cement concrete 1:4:8 mix (One cement four sand and eight hard broken stone) using 40mm gauge hard broken granite stone jelly for foundation including watering wherever necessary and laid in layers not more than 15cm thick compacting etc. complete complyin

Cement concrete 1:2:4 mix (One cement two sand and four hard broken stone) using 40mm gauge hard broken granite stone jelly for foundation including watering wherever necessary and laid in layers not more than 15cm thick compacting etc. complete complyin

Brick Work in cement mortar 1:5 mix using country bricks of size (8 ¾ x 4 3/8 x 2 3/4) including cost & conveyance of all materials to site

Supplying and fixing of GI Square tube including cost and conveyance and all labour charges etc complete.

Supplying and fixing colour galvalume sheet roof of 0.47mm thickand steel tubular box section of 100x50x3mm of 1meter interval including priming coat fixing in position with all necessary accessories complete complying with standard specification and as directed by the departmental officers.

Plastering the surface of walls with cement mortar 1:5 (one of cement and six of sand) 12mm thick in all floors Finishing smooth, scaffolding, curing etc., complete complying with standard specification as directed by the departmental officers.

Supply and fixing of Iron mesh(25X25mm) including cost and conveyance of all materials to site and all labour charges etc., complete

Supply and fixing Iron mesh Gate including all cost and conveyance of materials etc

GST Amount for providing Service to Government Contract Works for the above Construction Works. { GST Amount is the Total GST Amount for total overall quoted amount above this row in column "BB" for all works in this package}

Please Enable Macros to View BoQ information