SPL REPAIR OF BLDG NO P 07 08 X OR MD ACCN IN SECT A AT DINJAN MIL STN UNDER GE DINJAN

Amount

Demolition of brickwork built in cement mortar including taking out roots vegetation if any at any position and removal from site, all as specified and directed

Demolition of stone slabs and tiles of any description or thickness in floors, aprons, wall etc. all as specified and directed

Demolition of cement concrete (un reinforced) in ground floors and paving n. exc. 15 cm thickness (below or above ground level) removing rubbish off the premises etc all as specified and directed

Demolition of unreinforced cement concrete of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Taking down chowkhats or frame with shutters (without taking off shutters from the frame) not exceeding 1.50 Sqm each all as specified and directed

Taking down chowkhats or frame with shutters (without taking off shutters from frames) exceeding 1.5 Sqm but not exceeding 4 Sqm each all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Demolition and breaking up of drain pipes (salt glazed were or AC or reinforced cement concrete) set in cement mortar of 150/160mm dia complete all as specified and as directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, in roof covering including ridges and keeping serviceable sheets in safe custody for reuse in the work all as specified and directed

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/slabs of any thickness including cover fillets all as specified and directed

Dismantling floor hearth or wall tiling and stone slabs including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises etc complete all as directed

Taking down cement plaster or lime plaster on walls /ceiling of any description from concrete or brick wall etc including raking out joints, hacking for key, scrubbing down with water and disposing off the retreived debris as directed including necessary scaffoldings etc complete all as directed

Taking up or down 15 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed.

Taking up or down 20 mm bore steel water tubing galvanised including connections from trenches/wall/floor/ceiling etc and keeping serviceable quantity in safe custody for re-use at same site or other site complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment along external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging 12mm dia holes with cement mortar (1:2) to match the existing etc. in apron complete all as specified and as directed.

Providing and injecting Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and as directed.

Providing and injecting chemical emulsion for Post Constructional Antitermite Treatment At points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same with cement mortar (1:2) to match the existing etc. in apron complete all as specified and as directed.

M&L for plain cement concrete (1:3:6) type C-2, using 40mm graded stone aggregate as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for Pre-cast (Factory casted) cement concrete Kerb stone casted in PCC (1:2:4) Type B-1 using 20mm graded stone aggregates with plan or interlocking joints (as directed) with solid blocks, exc. 10 cm in width and setting and jointed in cement mortar 1:6, complete all as specified & directed.

M&L for precast cement concrete type B0 (1:2:4) (using 12.50 mm graded aggregate) as in louvers and jallies, 25mm thick (measured solid), including all mouldings but excluding frame set in cement mortar (1:6) complete all as specified and directed.

M&L for reinforced cement concrete (1:2:4) type B-1 (Nominal Mix) (using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed. Note : Reinforcement shall be measured and paid separately under relevant item.

M&L for brick work with sub class 'B' burnt clay bricks straight or curved on plan exc 6 meter mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with sub class 'B' burnt clay bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and as directed.

Cutting chases, pinning in brick wall making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels etc and cutting chases for concrete water tubing or concrete conduit wiring etc and making good, cutting not exc 10cm girth complete all as specified and as directed.

Use and waste formwork to soffits of suspended slabs such as roof slab, floor slabs, landings and similer works, for rough finished flat surfaces of concrete, thickness of slab not exc 200 mm, complete all as specified and directed.

Use and waste formwork to to edges of concrete flats, treads, breaks in floors, window cills, concrete rail ings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizon tal or sloping and similar work exc 10cm but n exc 20cm wide complete all as specified and directed

M & L for applying 15mm thick plaster with Polymer modified mortar fortified with SBR (Nitro Bond SBR 45) in proportion (1:3) by weight 5 ltr Nitro bond SBR 45 added to 50 Kg cement with 13 Ltr water and finished surfaces of ceiling,columns, beam and like etc complete all as specified and directed.

S&F for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) Solid decorative type flush door shutter of size 30mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S&F 35mm thick second class class hard wood glazed and skelton shutter, open rebated and prepared to receive glass gauze etc, divided into squares (with sash bar), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass exc., size of members of shutter as specified in SSR part-I, sec 8 clause 8.24(a), supplied and fitted to chowkats, including 3 Nos 100mm long butt hinges, 2 Nos 150mm aluminum handles, 2 Nos 150mm aluminium anodised tower bolt complete all as specified and directed.

S&F PVC moulded door Frame of size 50mm x 47mm made out of 5mm, single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelam sheet, reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing, complete all as specified and directed.

S&F Factory Made Solid PVC Moulded Door Shutter, 28 to 30mm thick (stiles), with 2, 4, or 6 raised panel design with 2mm thick Moulded prelam PVC Sheet on the front face & 2mm plain colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing, as directed.

S&F 200mm long mild steel, barrel tower bolts, stove enamelled black, with bright bolt and fixed complete all as specified and as directed.

S&F 150 mm long aluminium, anodised barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F for 75 mm size, butt hinges, heavy weight, cold rolled mild steel complete all as specified and as directed.

S&F extruded aluminium alloy handles, fabricated type, anodized, 150 mm long , complete all as specified and directed.

S&F for mild steel sliding door bolts, 250mm long, plate type, stove enamelled black, with bright bolts not less than 12mm dia with & including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate etc complete all as specified and as directed.

S&F for 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified and directed.

S&F in reepair continuous (Piano) hinges mild steel bright finish or electro galvanised, width of flaps when open 40mm complete as specified and directed.

S&F in repair mild steel 300 mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed.

S&F in repair Hasp and staple, safety type, aluminium anodised 100 mm including bolt to hinge plate and fixed with screws complete as specified and directed.

S&F in repairs curtain rails, Harrison rail, aluminium alloy chromium plated with fixing brackets, stops, rollers etc complete all as specified and as directed.

S&F in repair brass chromium plated tubular towel rail, D type, 60cm long, 20mm dia with brackets complete all as specified and as directed.

S&F in repair floor door stopper with overall length of cover plate 150mm of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F door seal aluminium rod with nylon brush of approved colour fixed to shutter with and including 20mm steel wooden screw , complete all as specified and directed.

S&F 50mm dia polished hard wood knobs fixed with thread screw and nut complete all as specified and directed.

S&F stainless steel magnetic door catched magnet of size 50 x 15 mm fixed with stainless steel screw on shelf/ sides wall and shutter complete all as specified and directed.

S&F mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 290 Gde-E-165 complete all as specified and directed.

S&F mild steel Bands, straps, supports or stays for rainwater, ventilating pipes, including bolts, if required: hooks (stay), heavy, for large gates; hook and pintle hinges: large hasps and staples; chains; hand made sliding bolts; clamps; hold fasts; wall ties; hooks for hanging fans; plain angle cleats for securing purlins to wood trusses or rafters; knee piece inserts; two way and three way straps, plate washers and similar small articles conforming to Fe-290 Gde-E-165 all as specified and as directed.

M&L for TMT bars 10 mm dia and over, as reinforcement for concrete cut to length, bent to shape required including cranking, bending, spirally hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia, complete all as specified and directed.

S&F mild steel Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) including drilling holes complete all as specified and as directed.

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and conforming to Fe 410-W (Gde-E-250) Quality A complete all as specified and as directed.

S&F pressed steel frames for doors local work shop made of size 105x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

S&F pressed steel frames for doors local work shop made of size 125x60mm with one or more rebates using cold rolled commercial mild steel sheet of 1.2mm thick including providing and fixing necessary lugs, 100mm butt hinges, lock strike plate, shock absorber etc and including PCC filling of hollow section using plain cement concrete (1:3:6) type C1 complete all as specified and as directed.

M&L for anodised aluminium frame of doors, windows, ventilators with one or more rebates including joining cleats for fixing etc including powder coating of minimum 50 micron thickness complete all as specified Note :- Weight of Aluminum sections for frames and shutters shall be only considered for payment. Cost of other consumables required for the item shall be deemed to be included in the quoted rate. However glass panes / Bakelite sheet / wire cloth / mortice lock / locking stay / floor spring / floor door stopper only will be measured and paid separately under respective items as supply only. Fixing element of these items shall be deemed to be included in quoted rate.

M&L for anodised aluminium window and ventilator shutters, fixed type, with or without sash bar, using aluminium section weighing not less than 0.55Kg per metre including necessary joining cleats, glazing clips, rubber neoprene packing, aluminium handles 2 numbers in each shutter, hinges, anodised aluminium snap beading, screws etc complete all as specified and as directed.

S&F for anodised aluminium grill, (anodised transparent or dyed to required shade according to IS:1868 with minimum anodic coating of grade AC 15) of approved design / pattern, with approved standard section and fixed to the existing window frame with C.P. brass/stainless steel screw @200mm c/c, including cutting the grill to proper opening size for fixing approved anodised aluminium standard section around the opening, complete all as specified and directed.

S&F for aluminium anodised snap grid frame work of size 600mm x 600mm frame work for ceiling with aluminium tee section of size 23.5mm x 26.4mm x 1.4mm thick and aluminium angle section of size 36.5mm x 25mm x 1.4mm thick, for false ceiling including Hangers 4 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including 4 mm thick non asbestos E-board (plain), HSPC fixed to frame including providing two coats of white wash complete all as specified and as directed.

M & L for Factory made single extruded WPC (Wood Polymer Composite) Frames/Chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/ moisture proof and fire retardant and fixed in position with MS hold fast/lugs/SS dash fasteners of required dia and length complete all as specified and directed. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). Note: For WPC solid door/window frames, minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be made.

S&F for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) Solid decorative type flush door shutter of size 18mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

S&F for Providing and fixing factory made single extruded WPC (Wood Polymer Composite) Solid Plain flush door shutter of size 18mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant. WPC to be laminated with PVC foil of minimum 14 microns thick of approved design pasted with hot melt adhesive on both faces of shutter and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as specified and directed. (Note: stainless steel butt hinges and necessary S.S screws shall be paid separately)

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fasteners, stainless steel bolts etc., of required size, on the top of floor or the side of waist slab with suitable arrangement complete all as specified and directed..

M&L for stainless steel soft close hydraulic clip concealed cabinet hinges fixed with stainless steel screws complete all as specified and directed.

S&F 0.71mm thick plain, aluminium sheeting, Alloy 31000 H4 in ridges, hips, valley gutter, drip and straight flashing (as in crumple joint) complete all as specified and as directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of profile as approved, any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed.

S&F for pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and as directed. Note : Colour of ridge shall be same colour as that of sheet used for roof.

S&F 1mm Thick 150mm dia Mild steel sheet eaves gutters, galvanised class 3, half round with rounded edges, complete all as specified and directed.

M&L for rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations complete all as specified and as directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc and brushing neat cement slurry with 3.0kg of cement per sq. metre complete all as specified and directed

M&L for coloured 450x300x7-8 mm thick glazed ceramic tiles on vertical surfaces such as skirting, dado and risers to steps etc, set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match, over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.06 Sqm but not exceeding 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles with and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 15mm thick screed bed or bedding layer of cement morter (1:6) for laying of floor finishes complete all as specified and directed.

M&L for non skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm, as in skirting. set and jointed in neat cement slurry and pointed in coloured cement to match the shade of tiles over and including 10mm thick backing coat in cement mortar (1:4) , complete all as specified and directed.

M&L for prepolished,chequered cement concrete tiles of size 25cmx25cmx22mm thick, as in floors etc, including 15 mm thick screed bed or bedding in cement mortar (1:6) and set and jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and as directed.

M&L for 18-20mm thick granite slabs of any type (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like, set and jointed in net cement slurry and pointed in white cement (1:2) using marble dust with admixture of pigment to match shade of granite including necessary moulding at edges laid over and including 20mm thick cement mortor screed bed in cement mortor (1:6) complete all as specified and directed.

M&L for Marbel work of 18-20mm thick of green colour (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in verticle surface in/over 10mm thick screed bed of cement mortar (1:3), including pointing in white admixture of pigments to match with marble of any shade other than white and black all as specified and directed.

M&L for machine cut kota stone slab 20-25mm thick in floor laid over and including 20mm thick screed bed or bedding layer of cement morter (1:6)and jointed with grey cement slurry @4kg/Sqm mixed with pigment to match the shade of the slab including rubbing and polishing complete.

M&L for Kota stone slab 20-25mm thick in riser of steps, skirting,dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab over and including 10mm thick backing coat in cement mortar (1:4) including rubbing and polishing complete all as specified and directed.

M & L for cutting holes in stone/RCC/granite slab for inserting cocking gas cylinder pipe and making good complete all as specified and directed.

M&L for 75 mm thick, plain cement concrete (1:3:6) type C-2 (using 40mm graded stone aggregate) as in plinth protection/ hard standing etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand (1:2) complete all as specified and as directed.

M&L for 75mm thick PCC (1:4:8) type D-2 (using 40mm graded crushed stone aggregate) as sub base of flooring complete all as specified and directed.

M&L for 25 mm thick PCC (1:2:4) type B0 (using 12.5 mm graded stone aggregate) as in under layer of tiles flooring & finishing the surface rough to receive screed bed etc complete all as specified and directed.

M&L for 15 mm thick rendering in cement mortar (1:6) on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for rendering 5mm thick in cement morter (1:3) on ceiling surfaces, finished even and smooth without using extra cement, complete all as specified and directed.

M&L for rendering 15mm thick in cement morter (1:4) on fair faces of brick work or concrete surfaces, WPC shall be mixed with morter as directed, finished even and smooth without using extra cement , complete all as specified and directed. (Note: WPC shall be measured and paid separately as supply only)

Supply only Water Proofing Compound of approved make all as specified and directed.

M&L for applying three coats of white wash on new ceiling surface including preparation of surface, complete all as specified and directed.

M&L for preparation old decorated plastered or unplastered surfaces of ceiling by brooming down or steel wire brushing, scraping down, the surfaces covered by smoke soot, growth of moulds and moss, efflorescent, having oil and greases spots and applying one coat of white wash complete all as specified and as directed.

M&L for preparation newly plaster surfaces of wall, chajja, facia etc and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted) with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfaces using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and acessories complete all as specified and directed.

M&L for complete removal of existing treatment from walls by scrapping with mechanical wall sander (having mechanical vaccum mechanism) having RPM not less than 1500, sanding pad of 80 Grit having dia of 7"/9" to make the surface free from dust, loose paint etc. and applying two coats of 100% premium Acrylic emulsion paint having VOC less than 50 gm/ litre and UV resistant as per IS-15489:2004 alkali and fungal resistant exterior paint of required shed (company depot tinted) with silicon additives 1.43 litrs/ 10 Sqm over and including primer coat of exterior primer applied 0.90 litre/10 Sqm over new surfaces using Airless spray technology with maximum working pressure of 3300 PSI and capable of operating single spray gun with a maximum material hose length of 30 mtr, the spray machine should be of reputed manufacturer with pro guard technology and capability of tracking pressure and paint usage and certified by paint manufacturer and as mentioned in PS and acessories complete all as specified and directed.

M&L for complete removal of existing treatment of wall and applying two coats of oil bound distemper over 1mm to 1.5mm thick wall care putty over and including one coat of primer complte all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over 1mm thick wall care putty over and including one coat of primer complte all as specified and directed.

M&L for preparing of new wood and wodd based surfaces of any description , over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified and directed.

M&L for preparing of kerb stone, new untreated concrete or plastered surface of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint in black and white colour over a coat of primer, complete all as specified and directed.

M&L for preparing of new steel surfaces of any description , over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer, complete all as specified and directed.

M&L for preparing of old steel & iron surfaces of any description, not otherwise described, over 10cm width or girth and applying one coat of synthetic enameled paint complete all as specified and as directed.

S&F 15 mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed.

S&F 20 mm bore, steel tubes, galvanised, medium grade with all fittings & fixed complete to wall and ceiling or laid in floors etc complete all as specified and directed.

Relaying/refixing only old serviciable galvanised steel tubing 15 mm bore in new or old location using new fitting and fixures complete trenches/walls/floors complete all as specified.

Relaying/refixing only old serviciable galvanised steel tubing 20 mm bore in new or old location using new fitting and fixures complete trenches/walls/floors complete all as specified all as directed.

Supplying and laying of 20mm outer dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified and directed.

S&F in repairs, 15mm Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed, complete all as specified and directed.

S&F in repair 15 mm bore, Pillar taps, fancy type, cast copper alloy, chromium plated with capstan heads, screwed down high pressure with or without lettered 'Hot or Cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and as directed.

S&F in repairs 15 mm bore, stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions complete all as specified and directed.

S&F in repairs soap dish of stainless steel, fixed to plugs with chromium plated brass screws complete all as specified and as directed.

S&F in repair sinks made of stainless steel 1.0mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or includingfixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowL size 410mm x 330mm x 160mm complete all as specified and directed.

S&F vitreous china Semi pedestal pattern (Anglo Indian type) white connection to trap 'P' or 'S' and flush pipe etc seat cover and making good to disturbed surfaces of floor by filling with PCC 1:4:8 type D-2 to match with existing including taking down the existing old one all as specified and as directed.

S&F in repairs vitreous china wash basin, size 550x400mm, white, flat back, including 32mm bore PVC (HDPE) waste pipe 450mm long, 32mm bore CP waste coupling, chain, plug and porcelain stopper & brackets including cutting for and pinning in ends of brackets but excluding tap complete all as specified and as directed.

S&F in repair PVC low level flushing cistern, 10 liter capacity, valveless, symphonic action type with inlet, ball valve, float and handle incl bracket, PVC connection pipe and flush pipe of polyethylene of low or high density complete all as specified and as directed.

S&F plastic water closet seat, back, closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete all as specified and as directed.

S&F in repair 450mm long PVC connections 15mm size with PTMT nuts, complete all as specified and directed.

S&F in repairs flexible (coil shaped) PVC waste pipe for sink and wash basin suitable for 32mm/40mm dia, lenth not less than 70 cm, connected to PVC waste coupling/fittng complete all as specified and directed.

S&F in repair MS grating 75/100mm dia, with or without hole for waste pipe of approved make including fixing with cement mortar(1:6) to floor/nahani trap etc complete all as specified.

S&F wall mounted modern kitchen utensil dish rack stainless steel (31 x10 x 30) inches complete all as specified and as directed.

S&F 15 mm bore wall mixer, cast copper alloy with L bend with provision for over head shower, complete all as specified and directed.

S&F in repairs sink mixer wall mounted regular spout with long neck complete all as specified and as directed.

S&F in repair PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F in repair PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints fixed to walls, complete all as specified and directed.

S&F in repair PVC (SWR) pipes type 'B' 110mm bore, single socketed in any length with rubber ring joints fixed to walls using MS holder bat, fixed complete all as specified and as directed.

S&F PVC (SWR) bends any radius 110mm bore with access door, complete all as specified and directed.

S&F PVC (SWR) bends any radius 110mm bore, complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm bore with access door, complete all as specified and directed.

S&F PVC (SWR) bends any radius 75mm bore, complete all as specified and directed.

S&F in repair PVC (SWR) vent cowl 110mm bore, complete all as specified and directed.

S&F PVC (SWR) vent cowl 75mm bore, complete all as specified and directed.

S&F in repair PVC (SWR) floor trap dia of outlet 75mm, plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F for PVC SWR gully trap plain with grating including jointing with solvent cement, dia of outer 125/110mm complete all as specified and as directed.

S&F in repair brass cast copper alloy, chromium plated shower rose 125mm size with shower arm 15mm size, 195mm long fixing to steel pipe or to unions complete all as specified and as directed.

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

S&F in repair stainless steel peg set of 6 peg , 45 cm long complete all as specified and directed.

S&F in repair 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical or vertical with closed top) as per IS 12701:1996, hoisted and fixed in position including provision of 20/15mm bore medium grade pipe for connecting inlet, outlet, overflow and washout pipe including 20 mm bore, ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixedcomplete all as specified and as directed.

S&F in repair 20 mm bore Gun metal gate or globe valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

M&L for concrete bed , plain cement concrete (1:3:6) type C-2 ( using 40mm graded crushed stone aggregate) in bedding to SGSW/NP2 drain pipes, including packing under and haunching against the sides of pipes after they are laid and tested, for 150mm pipe, complete all as specified and as directed.

M&L for salt glazed stone ware drain pipes 150 mm bore, grade 'A' laid in trenches, jointed cement mortar and tested complete all as specified and as directed.

Cutting into existing manholes for connecting new drains, making good to pipe and plastering the distrubed portions in cement mortar (1:3) to match with surround surfaces, cutting out existing benching and forming branch channel (1/2 round or 3/4 round section) in cement concrete (1:2:4) type B-1 finished smooth and reforming benching as required for 150/160mm bore pipe complete all as specified and as directed.

S&F for 50mm thick steel fibre reinforced (SFRC) manhole cover with iron frames (medium) complying to the standard specification as mentioned in the IS 12592 BIS standard minimum load bearing capacity 5 ton / sqm in squre, rectangular shape of size 300 x300, 450 x 450, 600 x 600 complete all as specified and as directed.

Forming Construction joint 30mm deep x 10mm wide filled with sealing compound, Grade ‘A’, complete all as specified and directed.

M&L for water proofing treatment on RCC roof etc. comprising with the following operation & as specified herein below:- (a) Taking down existing old tarfelt, bituminous compound including cleaning & removing debris to a distance exc 100 m n.exc.250m. (b) M&L 25 thick cement concrete type B0 1:2:4 ( 12.5 mm graded aggregate) finished even and smooth. (c) M&L for 15 mm thick screed bed in 1:6 finished even and smooth. (d) Preparing & cleaning of fully dried cement plastered surface. (e) Applying one coat of cold bituminous primer to the plastered surface @ 0.25 litres per sqm conforming IS-3384. (f) A layer of APP based polymeric membrane membrane 3mm thick (minimum) weighing 3.5 kg per sqm reinforced with polyster non woven fabric (weighing not less than 160 gms/sqm) shall be applied over bituminous primer as specified above. Application of polymeric membrane shall be by torch application. The over lap shall be minimum 100 mm on transverse direction and 75 mm in longitudinal direction. (g) One coat of aluminium paint over APP membrane @0.11Kg/Sqm. Note:- Prior to execution of the APP Membrane works, leak proof test shall be done by ponding water on roof slab to minimum depth of 25 mm. The entire roof slab shall be flooded with water for 48 hours. The necessary barrier shall be made to make feasible to stagnate water for 48 hours on roof slab.

Materials and labour for special treatment for sunken portion of WCs/ Bath & toilet executed in following stages:- Stage 1 :- Demolition of WC including lime concrete and cement concrete etc and preparing the surfaces of existing sunken portion of WCs or bath etc with wire brush to remove all loose dirt, oil grease etc including removing debris from site of work etc . Stage 2:- Providing 10mm thick plaster in CM 1:3 mixed with integral water proofing chemical of Dr. Fixit Pidicrete URP or plaster seal of STP Ltd in the proportion/quantity all as per Manufacture's instructions.Complete. Stage 3:- Apply Dr Fixit Primeseal primer or Equivalent of STP Ltd (and allow to dry for 8 hours) all as per Manufacture's instructions. Stage 4:- Apply two coats of water proofing elastomeric coating system of Dr Fixit Raincoats with DFT 100 Micron or shalicry 215 of STP (The surface after painting one coats shall be allowed to dry for 6 hours before next coats) all as per Manufacturer's instructions. Stage 5:- Rendering 10mm thick in CM 1:3 mixed with Integral water proofing chemical Dr Fixit Pidicrete URP or plaster seal of STP Ltd all as per Manufacture's instructions. Stage 6. All CI joints shall filled with mixture of cement fine sand and plaster seal of STP Ltd or Dr Fixit pidicrete URP all as per Manufacture's instruction. Stage 7:- Making holes in wall and fixing 600mm long 40mm dia medium grade GI spout for draining the surplus water if any . Stage 8:- Carry out ponding test for 48 hours to ensure water tightness of repaired sunken portion water tightness of repaired sunken portion and filling of sunken portion for cement concrete Type E2 1:5:10 using 40 mm graded aggregate as in lean concrete complete all as specified and directed. Note :- (a) Only plan area shall be measured and accounted for payment under this item. (b) Depth of sunken portion of WC's/Baths shall be upto 35cm, which is to be taken into account while quoting the rate against this item. (c) Rate quoted by Contractor shall be deemed to be included for all the horizontal and verticale treated surfaces of sunken portions of WC & Bath.

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc all as specified and directed.

Taking down carefully old serviceable Main Switch, DB's consisting of MCBs wooden/GI/MS sheet board etc for kept in store and for later use all as directed (To be measured only when found serviceable in all respects complete for reuse) all as specified and directed.

Taking down old unserviceable PVC casing caping or conduit any type complete all as specified and directed.

Taking down ceiling fan /exhaust fan and refixing after minor repair such as capacitor, bearing replacement and painting as per existing complete all as specified and as directed.

M&L for concealed point wiring with two runs of FRLSH PVC insulated unsheathed, 1100 V grade cable multi stranded copper conductor of size 1.5 sqmm and one single core PVC insulated unsheathed stranded copper conductor of size 1.50 sqmm green in colour as earth lead, drawing through in and including PVC rigid conduit of size not less than 20mm, with all fittings & accessories including provn of MS sunk terminal box of appropriate size suitable for switch fixed flush to wall for mounting switch, sockets, fan regulators etc with 3mm thick hylum sheet top cover with screws & cup washers for one light / fan point / call bell controlled by one switch one way 5 Amps complete all as specified and directed . NOTE : Cost of cutting, chieseling, and making good the disturbed surfaces (if any) matching with the existing surface is deemed to be included in the unit quoted rates..

Description all as per Ser Item No.146 here-in-before but for One 2/3 pin socket outlet 5/6 Amps on independent board.

Description all as per Ser Item No.146 here-in-before but for One light point controlled by two nos two way switches.

Description all as per Ser Item No.146 here-in-before but for One 2/3 pin socket outlet 5/6 Amps on the same board with other switches.

Description all as per Ser Item No.146 here-in-before but for one switch socket combination 15/16 Amps on independent board with cable 2.5 sq mm size and earth wire 2.5 sqmm

Description all as per Ser Item No.146 here-in-before but for one switch socket combination 15/16 Amps on independent board with cable 4 sq mm size and earth wire 4 sqmm

S&F Switch piano, flush type, single pole, one way switch 5 Amps. (Note :- switches to be used both for new point wiring and old switch boxes of existing wiring)

S&F for switch piano, flush type single pole, 230 volts, 5 Amp two way bearing ISI marked complete all as specified and as directed.

S&F Socket outlet 5 in 1, 5 Amp flush type universal, 240 volts, complete all as specified all as directed.

S&F Switch socket combination 3/5 pin, 2 in 1, 5 Amps flush type, 240 volts, complete all as specified all as directed. .

S&F Switch socket combination multipurpose 3/5 pin, 5 A /16 Amps, 5 in 1, flush type, 240 volts, complete all as specified all as directed. .

S&F Ceiling rose surface PVC, 3 terminals 25x50mm all as specified all as directed.

S&F electronic step regulator (speed regulation in 5 steps) suitable for ceiling fan 1200 sweep/1400 mm, 120 Watt complete all as specified and directed.

S&F for lamp holder PVC/Polycarbonate type with back plate suitable for batten fittings including fixing for one 9 Watt LED Lamp complete all as specified and as directed.

S&F Bell Push Flush type 5 Amp, 240 volts, complete all as specified all as directed.

S&F Bell Ding-Dong AC 230 V Single Pole complete all as specified and as directed.

S&F LED lights fitting 1x 18/20W, 220V, AC decorative box type with driver, holder including LED Light fitting inverter type with 04 hrs backup connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

S&F MCB distrubution board TPN 4 way double door, sheet steel, phosphatised, powder coated with 200 amps bus-bar, neutral link, earth bar and din rail, 415 V, complete all as specified and directed.

S&F MCB distrubution board SPN 8 way double door, sheet steel, phosphatised,powder coated with 200 amps bus-bar, neutral link,earth bar and din rail 240 V , complete all as specified and directed.

S&F MCB TPN, 415 volts 40- 63 Amps, 16 KA breaking capacity, C series, adjustable thermal and adjustable magnetic all as specified and directed.

S&F MCB Single pole and neutral, 40 Amps, 240 volts 10 KA rupturing capacity, C series complete all as specified and directed.

S&F MCB Single pole and neutral, 6 to 32 Amps, 240 volts 10 KA rupturing capacity, C series complete all as specified and directed.

S&F MCB Single pole, 240 volts 6 to 32 Amps 10 KA rupturing capacity, C series all as specified and directed.

M&L for sub main wiring with two run of 6 Sqmm (Nominal area) single core cable PVC insulated, multistranded, unsheathed, copper conductor cables (FRLSH), 1100 Volts grade drawn through PVC Conduit of suitable size, fixed on surface of wall/ceiling etc with all necessary fittings and accessories and one run of 6 Sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, copper conductor (FRLSH) as earth wire and duly connected to common earth point complete all as specified and as directed. Note : (a) PVC Casing-caping/conduit, two run wiring cables and one run of earth wire will be measured as one length (b) All incoming and outgoing cable shall be connected by using proper lugs & sockets.

Excavating in trenches not exc 1.5m wide and n.exc 1.5 m in depth, for foundations, etc, or for shafts, wells, cesspits, manholes, pier holes, cable trench etc and not exceeding 10 square meter on plan for manholes etc and not exceeding 1.5m in depth and getting out in soft/loose soil complete all as specified and directed.

Returning filling in with approved excavated soil including spreading, leveling, watering and well ramming in layers not exceeding 25cm thick complete all as specified and directed.

Removing excavated soils to a distance not exceeding 50 metres and depositing where directed at a level nexc. 1.5 metre above the starting point complete all as specified and directed.

M&L for clear sand cushioning with dry clean sand for protection of cable, 15cm below the cable and 8cm above the cable, complete all as specified and as directed. Note : Punned thickness shall be measured for payments.

S&F unreinforced precast concrete cable cover class LV, type 1, flat size 250 x 150 x 40 mm for cable protection, complete all as specified and as directed.

Boring of holes horizontal for laying not less than 80/50/40/32mm pipe (minimum depth 0.75 mtr from top level) under the road pavement, hard standing using trenchless technology complete all as specified and as directed. Note : cost of accessories required for making hole/bore deemed to be included in the quoted rate.

Supply, laying, jointing, commissioning and testing cross-linked polyethylene (XLPE) insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric power cables (heavy duty) 1100 Volt grade with stranded aluminium conductor of size 35 sq.mm 3.5 Core, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, under floors, through GI pipe complete all as specified and as directed. Note : (1) Pipes shall be measured and paid separately under relevant items. (2) Excavation and earth work shall be measured and paid separately. complate all as specified and directed.

S&F in repairs 35/40 Watt LED building security light new generation energy saving and environmental friendly long life LED street light made up of pressure die cast aluminium housing with high power LED as lighting source and lens embeded PC cover having Bottom Opening seperate driver compartment with IP66 protection and impact resistance of IK08. including all fixing arrangement and taking down old light fittings of any type complete all as specified and as directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, Inverter type 10 watt 220 V AC with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and as directed.

M&L for earthing complete with GI earth plate electrode 600mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25m below ground level with the top edge of earth plate at depth not less than 1.5m below ground level connected to galvanised earth lead wire 4.0 mm dia by means of bolts, nuts, check nuts and washers protected by 15mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, pre-cast RCC 1:2:4 type B-1 cover slab of size 350x350x50mm reinforced with 8mm dia TMT steel bars @ 15cm centre to centre in both direction and 10mm dia MS handle of suitable size, charcoal or coke and salt in alternative layers, necessary earth work in soft/loose soil all as shown in Electrical Plate No 3 of MES Schedule Part I and testing the base in which pit cover rests made up of MS angle iron (Frame) complete as specified and as directed.

M/S CHANDAN ENTERPRISE (BID ID -3412559)

M/S. UDDUG CONSTRUCTION (BID ID -3412399)

FREEZCON (BID ID -3412081)