PROVN OF DOUBLE STOREY OFFRS (TRANSIENT) RECEPTION ROOM ANTE ROOM BAR ATT LADIES and GENTS TOILETS AT TRANSIT CAMP BANIHAL UNDER AGE (I) BHALRA

Amount

Excavation in trenches not exc 1.5m wide and not exc 1.5m deep for foundation etc or for shafts n.exc 10 Sqm on plan and n.exc 1.5m in depth and getting out in any type of soil complete all as specified and directed by Engineer-in-Charge.

Material and labour for PCC 1:4:8 type D-2 (using 40mm graded stone aggregates) for foundation filling & mass concrete.

Use of water of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work, vertical or to batter for rough finished surface complete all as specified and directed by Engineer-in-Charge.

Use of water of formwork for rough finished surface of concrete (flat surface) to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified and directed by Engineer-in-Charge.

Use of water of formwork for rough finished surface of concrete to sides and soffits of floor or roof beams, beam haunchings, girders, lintels, cantilevers, shelves including supports,overhangs etc also splays between floors and beams etc complete all as specified and directed by Engineer-in-Charge.

Use of water of formwork for rough finished surface of chullah hoods,chajjas,troughs and similar items including edges complete all as specified and directed by Engineer-in-Charge.

Use of water of formwork to soffits of suspended slabs such as roof slabs,floor slabs,landings and similar work not exceeding 200mm thick (Horizontal or sloping) for rough finished surface complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete (design mix) in M-25 (20mm graded stone aggregate) foundations, including rafts, footings, foundation beams, plinth beams; bases for columns, etc. basement slabs,under-reamed piles and mass concrete etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete (Design mix) in M-25(20mm graded stone aggregate) in columns, pillars, piers etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete (Design mix) in M-25 (20mm graded stone aggregate) in beams, cantilevers, bressummers, lintels over 1.5m span etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete (Design mix) in M-25 (20mm graded stone aggregate) in chajjah etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for Reinforced cement concrete (design mix) in M-25 (20mm graded stone aggregate) slabs supported on walls,beams and columnsin floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like etc complete all as specified and directed by Engineer-in-Charge.

Material and labour for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

Description same all as per srl item No 13 here-in-before but 6 to 8 mm dia all as specified and as directed.

Description same all as per srl item No 13 here-in-before but 5 to 10 mm dia and over upto and including 10mm dia in stirrups,spacers and binders all as specified and as directed.

Material and labour for old size bricks work with subclass 'B' bricks straight or curved on plan n exc 6m mean radius built in CM 1:4 complete all as per specified and directed by Engineer-in-Charge.

Material and labour for brick work with sub class B bricks,in one brick thick honey comb walling, straight or curved on plan to any radius in built in CM 1:4 complete all as per specified and directed by Engineer-in-Charge.

Supply and fixing steel work in roof trusses (framed), trussed, purlin, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats etc and other steel works including special shaped washer etc and other works complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade Fe-410 W (Gde-E-250)

Supply and fixing pre-painted galvanized aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified.

Supply and fixing 0.5mm Pre-painted galvatume aluminium Zinc coating plain steel sheet of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall , fixed with self taping screws as specified.

Material and labour for 4 mm thick Non asbestos fibre cement building boards in false ceiling on and iclu aluminium snap grid frame work 605 x 605mm with using 36.5mm x 23.5mm x 1.5mm thick main tee, 23.5mm x 23.5mm x 1.28mm cross tee and 25mm x 25mm x 1.5mm angles fixed to perimeter of wall including necessary supporting hangars with 6mm dia GI wire and J bolts washers nuts for securing frame work to ceiling suspended @120c/c both ways, complete all as specified and directed by Engineer-in-Charge.

Material and labour for providing 25 mm thick PCC 1:2:4 type B0 (using 12.5 mm graded stone aggregate) as in flooring receiving screed bed complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic tiles of 10mm thick (Square/rectangular)polished,area of each tiles not exceeding 0.36Sqm in floors etc.. Set in and jointed in neat cement slurry and pointed in white or coloured cement to match with light shade over 10mm thick cement screed bed layer in CM 1:4 complete all as specified and directed by Engineer-in-Charge.

Material and labour for vitrified ceramic tiles of 10mm thick (Square/rectangular)polished in skirting in height 150mm. Set in and jointed in neat cement slurry and pointed in white or coloured cement to match with light shade over 10mm thick back coat in CM 1:3 complete all as specified and directed by Engineer-in-Charge.

Material and labour for mirror polished machine cut kota stone slab flooring 20mm to 25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with mirror cut polish complete and including 20mm thick screed bed or bedding layer in cement mortar (1:4) complete all as directed by Engineer-in-Charge.

Material and labour for mirror polished machine cut kota stone slab 20mm to 25mm thick over cement screed base, laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing with mirror cut polish complete in riser of steps, skirting, dado and pillar and including 10 mm thick plaster in cement mortar (1:3) all as directed by Engineer-in-Charge.

Material and labour for Non-skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm,in floor etc, set and jointed with neat cement slurry and pointed in white or coloured cement to match including 10mm thick screed bed for laying floor finish in CM 1:4.

Material and labour for coloured glazed ceramic tiles 350 x 450 x 7 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc., set and jointed in neat cement slurry and pointed in white or Coloured cement to match including 10mm thick plastering on wall surface to receive dado tiles in CM1:4.

Supply and fixing vitreous china wash down water closet, pedestal pattern one pice type (EWC), white, with 'P' or 'S' trap, with PVC water closet seat, black or white, closed pattern, with flat bottom and cover and mild steel chromium plated or aluminised hinging device including taking down and removal of existing old water closet with scat cover all as specified and directed.

Supply & fixing ABS mild steel chromium plated health faucet suitable for 15mm dia pipe with 1.50 mtr long tube & hook complete all as specified and directed. (Make : CERA)

Supply and fixing half stall urinal including providing and fixing plugs, bedding urinal against wall, securing urinal to plugs, pointing around urinal and making connections to flushing pipe and outgoing pipes complete all as specified and directed by Engineer-in-Charge.

Supply and fixing vitreous china wash hand basin white flat back of size 550x400 mm including bracket, (pedestal pattern )cutting for and pinning the ends of brackets or erecting stands exclusive of waste pipe but including brass chromium plated waste coupling with long screwed sank and fly nuts complete all as specified.(Make:-CERA)

Supply and fixing flush pipe of PVC 32 mm dia for low level cistern pipes.

Supply and fixing Brass CP wash hand basin Mixer for mixing hot and cold water for iron pipe and fixed 15 m dia pipes all as specified and directed by Engineer-in-Charge. (Make : CERA))

Supply and fixing in repair brass choromium plated D type tubular towel rail 20 mm dia and 600mm long with brackets.

Material and labour for solid PVC door frame of size 50mmX47mm made out of 5mm plain colour PVC foam sheet meter cut to two corner and jointed with 2 nos of 1500mm long bracket of 15x15 squre tube .the two vertical door profile are to be reinforced with 19x19mm squre tube of 19 gauge EPDM rubber gascut weather seal to be provided through out the frame frame shall be fixed to wall using 65x100mm long ms screw through the frame by using PVC fasterner (inc hold fast)and minium of 4 nos of screw to be provided for each vertical member & 2 nos for horzintal all as specified as per drawing.

Factory made solid PVC door shutter with wood free core 28 to 30 mm thick (stiles) with 2,4 or 6 raised paneel design with 2mm thick moulded PVC sheet on the front face and 2mm plain colour PVCsheet on back face and moulded plain colour PVC 'c' chanel having PV C sheet for top rail ,lock rail & bottom rail panneling, supply and fixing in the frame at site as per specification.

Powder coated anodised aluminum window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 Kg/m including cleats, glazing clips, rubber packing, anodised aluminium snap beading, screw, anodised aluminium fittings such as peg stays 150mm long (1 No), hings type B-21 100mm long, (2 Nos) suitable handle (1 No) complete all as specified.

Supply and fixing of stainless steel (SS grade 304), curtain rod 25mm dia 1.20mm thick with necessary SS fittings i.e brackets, ends stops, end caps etc complete all as specifed and directed.

Material and labour framed work such as grills etc with ends of bars shouldred and /or riveted ,or forged into spike, framed guard bars and similar work conforming to Fe 290.Gde-E-165.

Supply and fixing stainless steel wire cloth, 0.36 mm nominal dia of wire and average width of aperture 1.4 mm and fixed with stainless steel wire staples complete all as specified.

Supply and fixing steel ventilators with centre hung shutter including hinges, steel peg stay, complete all as directed.

Material and labour for sheet glass ordinary quality and glazing with oil putty in square n. exc 0.50 sqm each pane, 5.5 mm thick.

Supply and fixing butt hinges medium weight of size 100mm complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 150mm size cast type Aluminium anodised D' type handles complete all as specified and directed by Engineer-in-Charge.

Supply and fixing 200mm Long Aluminium anodised barrel tower bolts of extruded section and fixed complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Aluminium anodised 300mm sliding door bolt with hasp staple and fixing clips of sheet,cast or extruded sections

Supply and fixing powder coated Anodised aluinum frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc complete all as specified and minimum thickness of powdere coating 50 micron

Supply and fixing Powder coated aluminium door shutters, aluminum section weighing 0.55 Kg/m including necessary jointing cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screw etc complete all as specified

Material & labour door closer hydaulically regulated, designation No 02, Universal type, suitable for door shutters of 701 to 850 mm in width and of weight between 36 to 60 Kg and fixed as in repairs (aluminium die)

Material & Labour fo providing and fixing stainless steel (grade 304) railing made of hollow tubes, Channels, platesetc, including welding, grinding, buffering, polishing and making curvature (where ever required) and fitting the same with necessary stainless steel nuts and bolts complete, including fixing the railing with necessary accessories & stainless steel dash fastners, stainless steel bolts etc, of required size, on the top of floor or the side of waist slab with suitable arrangement, complete all as specified.

Material and labour for rendering 15 mm thick in CM 1:6 on fair faces of brick work or concrete wall surfaces & finishing the surfaces even and smooth without using extra cement complete all as specified.

Material and labour for 15mm thick plastering in cement & sand mortar 1:4 on fair faces of brick work or concrete surfaces, finishing the surface even and smooth without using extra cement complete all as specified.

Material and labour for 5mm thick plastering in cement & sand mortar 1:3 on fair faces of brick work or concrete surfaces of ceiling, finishing the surface even and smooth without using extra cement complete all as specified.

Material and labour for applying two coat of oil bound distemper new wall surfaces over a coat of chalk whiting/primer and a coat of putty comlete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of new plaster surface & apply two coats of cement based paint over a coat alkali primer resistance.

Material and labour for preparation for newly plastered surface & applying three coats of white wash complete all as specified and directed by Engineer-in-Charge.

Material and labour for preparation of newly steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome complete all as specified and directed by Engineer-in-Charge.

Supply and fixing in repair grating square 150mm size of PTMT (minimum weight 100 gms).

Supply and fixing PVC connections 15mm size with PTMT nuts of length 600mm.

Supply and fixing galvanised medium grade steel tubing 20mm bore with all fittings fixed to walls complete all as specified.

Supply and fixing galvanised medium grade steel tubing 15mm bore with all fittings fixed to walls and floor complete all as specified.

Supply and fixing bib taps, fancy type chromium plated cast copper alloy with crutch or butterfly handle, screwed for iron pipe or for brass ferrule of bore 15 mm

Supply and fixing stop valves/angle valve, CP Fancy type screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union of bore 15mm.

Supply and fixing stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for union of bore 20mm.

Rotational moulded polyethlene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I,capacity of water tank 1000 Ltr each.

Material and labour for 75mm PCC 1:3:6 type C2 using 40mm graded stone aggregate as in plinth protection ,foot path and hard standing complete all as specified and directed.

Supply and fixing PVC SWR pipes 75 mm bore single socketed in any length with rubber ring joint fixed to wall or laid in trenches or in floors with steel clamps complete all as specified and directed by Engineer-in-Charge.

Supply and fixing (PVC (SWR) pipe 110 mm bore single socketed in any length with rubble ring joints as in weep holes complete all as specified and directed by Engineer-in-Charge.

Removing of excavated soil to a distance exc 250m but n exc 500m and deposited where directed n exc 1.5 m above the starting point

Returning, filling incl spreading levelling watering and well ramming in layers n exc 25 cm thick each layer.

Excavating in post holes (or similar holes) each n exc 0.5cum, getting out in hard/dense soil, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in any type of soil.

Material and labour for PCC 1:3:6 Type C2 (using 40mm graded aggregate) as in foundation, filling and mass concrete as directed and specified by Engineer-in-Charge.

Supply and fixing Rolled mild steel plates as in guesset plates, base pletes etc complete all as spd.

Material and labour for PCC 1:2:4 type B1 (Using 20 mm graded aggr) as in coping and similar works incl necessary from work all as specified.

Material and labour for precast cement concrete type B1 (1:2:4) using 20mm graded stone aggragate as in cover slab,manhole cover etc all as directed by Engineer-in-Charge.

Supply and laying of USVC sewage UDS (under drainage system) pipes 160mm bore single socket, all thickness not less than 4.50mm type SN-4 (IS-15328) type 'A' heaving nominal ring stiffness should be 2KN/m2 with one collar per length of pipe with all fittings and connecting to existing manholes by cutting out and making the surface good to pipe, and incl necessary returning filling and levelling to the affected portions, the UDS pipes should meet the pressure requirements as per IS 15328:2003 including taking down old unserviceable pipes complete all as specified and directed by Engineer-in-Charge.

Concrete bed to drain pipes of bore 150mm including packing under,and haunching against the sides of pipes after they are laid and treated in cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate, all as specified.

Extra for forming fair finished drain 30 cm inner girth in cemet concrete using extra cement including forms moulds stopped ends etc.

M&L for Point wiring complete with FR PVC insulated unsheathed , 1100 V grade conforming to IS 694 , 1.5 Sqmm for light point and 2.5 sq mm for power point (Norminal area) multistranded ,copper conductor cable drawn through in non metallic rigid PVC conduit medium grade ,minimum 20 mm dia, ISI Marked, and connected accessories, mounting on suface of walls / ceilings /roofs etc or concealed in wall all as per site requirement with shunken box pressed type mild steel made out by16 gauge mild steel sheet with hold fasts and conceiled in suface of wall , 3 mm thick laminated sheet cover for mounting of switches, sockets outlets, regulators etc, fixed by suitable size of 04 Nos cadmium screwes including provision of FR PVC insulated unsheathed 1 Sqmm muiltistranded copper conductor cable as earth connectivity and connecting to common earth dolly complete all as specified and directed . Make for PVC conduit :- Plaza /Modi/Sudhakar And PVC cable : Havell's /Finolex /Plaza.

(i) One light / fan / bell point controlled by one switch.

(ii) One switch socket outlet 3 Pin, 5 Amps, SP on independent board.

(iii) One switch socket outlet 3 Pin, 5 Amps, SP on same board.

Description as per the Srl Item No. 82.00 here-in-before but with 2.5 Sqmm for point wiring and 1.5 sq mm for earth continuity conductor all as specified and directed for 3 Pin 5/15 Amps switch socket outlet.

Description as per the Srl Item No. 82.00 here-in-before but with 4 Sqmm for point wiring and 2 sq mm for earth continuity conductor all as specified and directed for AC 3 Pin 5/15 Amps switch socket outlet.

Supply and fix modular switch 1 way, 6 amps, 1 module, cat no AHFSXXW061 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL.

Supply and fix modular switch 1 way, 16 amps, 1 module, cat no AHFSXXW161 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL

Supply and fixing modular socket, 6 Amps, 3 pin combined 2 module, cat no AHFKPXW063 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL.

Supply and fixing modular socket, 6/16 Amps, 3 pin combined 2 module, cat no AHFKCXW163 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL.

Supply and fixing modular fan regulator, dimmer type, 400 watt, 2 module, cat no AHFRFXW005 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL.

Supply and fixing modular cover plate, 1 module, cat no AHFPLCWV01 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL.

Supply and fixing modular cover plate, 2 module, cat no AHFPLCWV02 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL.

Supply and fixing modular cover plate, 3 module, cat no AHFPLCWV03 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL.

Supply and fixing modular cover plate, 4 module, cat no AHFPLCWV04 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL.

Supply and fixing modular cover plate, 6 module, cat no AHFPLCWV06 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL.

Supply and fixing modular cover plate, 8 module, cat no AHFPLCWV08 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL.

Supply and fixing modular surface mounting plastic box of size 3 x 3, 1/2 module, cat no AHZXMIIX01 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL

Supply and fixing modular surface mounting plastic box of size 4 x 3, 3 module, cat no AHZXMIIX03 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL

Supply and fixing modular surface mounting plastic box of size 5 x 3, 4 module, cat no AHZXMIIX04 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL

Supply and fixing modular surface mounting plastic box of size 6 x 3, 6 module, cat no AHZXMIIX06 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL

Supply and fixing modular surface mounting plastic box of size 8 x 3, 8 module, cat no AHZXMIIX08 of Make : Havells (Crabtree) or equivalent model of Make : Indo Asian/HPL

Material and labour for ceiling rose, 3 terminal, PVC/ polycarbonate isolated body all as specified .Make:- Anchor/Plaza/Havell;s

Material and labour for single pole & neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 250 volts, 20 amp, 'D' curve, 10KA all as specified. (for AC)

Material and labour for single pole & neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB, 250 volts, 10 amp,'D' curve, 10KA all as specified. (for gyser)

Supply and fixing MCB SP 5-32 Amps 'B' series 240V 50Hz 10 KA suitable for lighting and other domestic loads complete including taking down all as specified and directed by Engineer-in-Charge. Make : C&S, Havells, Indoasian, ABB

Material and labour for sheet metal enclosure for DBs when MCBs to be used TPN, 6 way double door with 200 Amps bus bar all as specified.

Material and labour for MCB, TPN, 4 pole ,415 volts,63 amp, 10 KA, 'C' curve all as specified and directed. Make :- Havells Cat No DSMSCTNF063 OR equivalent

Supply and fixing MCB SPN 40 to 63 Amps 'C' series 240V 50Hz 10 KA suitable for lighting and other domestic loads complete taking down all as specified and directed by Engr-in-charge. Make : C&S, Havells, Indoasian, ABB

Sheet metal enclosure (factory made) double door for distribution board (when MCB's are to be used) Single pole neutral 240 V, 8 ways with 200 Amp rated busbar connectin with suitable size of thimbles and including taking down all as specified and directed by Engineer-in-Charge.

Material & Labour Earthing for complete with galvanised steel earth plate electrode, 600mmx600mmx 6.0 mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level,connected to galvanised earth lead wire 4.0mm dia by means of bolts,nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 5 connected to earthing test point all as specified or indicated including testing on completion sheet complete including taking down and all as specified and directed by Engineer-in-Charge.

Supply and fixing 1 x 20 Watt LED tube light fitting prewired with all accessories and including LED tube rod 20 Watt inlcuding connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor cable 3 core of size 0.50Sqmm. Make : Wipro, Havells, Syska, CG

Supply and fixing LED light fitting 1x9W/1x10W bulk head luminaires including LED light driver holder connercting up with three core flexible copper conductor cable of suitable size 230V,50 HZ all as specified and directed.

Supply and fixing high efficacy 2 x 2 recess LED luminaire with concentrated light for homogenous illumination, all as per cat no LHEWDRP6IL1W034 of Make : Havells or equivallent model of Make: HPL/Bajaj inluding provision of PVC insulated sheathed round flexible wire with multi strand copper conductor of size 1.5 sqmm 3 core 1100Volts grade all as specified and directed.

Supply & fixing ceiling fan complete with blades, down rods, electronic regulator and accessores, 230 V,1200 mm sweep with BEE 5 star rated all as specified and directed by Engineer-in-Charge.

Supply & fixing Exhaust Fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 300mm, complete all as specified and directed by Engineer-in-Charge.

Supply and fixing Electric Water heater storage type steel body with copper inner tank and heating element up to 2KW capacity 25 litres, 220 V with BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection pieces etc all as specified and directed by Engineer-in-Charge.

Supply and fix in replacement of decorative wall mounting 9W B22 LED lamp Cat No LHFOECE1TZ1B014, Make Havells inluding provision of PVC insulated sheathed round flexible wire with multi strand copper conductor of size 1.5 sqmm 3 core 1100Volts grade all as specified and directed.

Material and labour for non metelic,rigid, PVC conduit with accessories concealed in wall for drawing telephone / TV cables all as specified for the following sizes :

(i) 20mm bore

(ii) 25 mm bore

Supply and fixing PVC insulated overall PVC seathed, twin core cable with copper conductor suitable for Telephone drawn through conduit all as specified.

Supply and fixing PVC insulated overall PVC seathed, twin core cable with copper conductor suitable for TV connection drawn through conduit all as specified.

NOTE FOR ITEM NO 118.00 & 119.00 :- PVC conduit and conduit accessories measured and paid under respective items

Material and labour for modular type TV socket all as specified and directed.

Material and labour for modular type Telephone socket all as specified and directed.

Supply and fixing sheet metal box of size 75 X 75mm for Telephone Socketand TV Socket with hylam sheet.

Supply and fixing sub Main Wiring in PVC Conduit with two single core PVC insulated unsheathed multistranded flexible copper conductor cable of size 2x4 sqmm and one single core PVC insulated multistranded unsheathed flexible copper conductor of size 2.5 sqmm size (green colour) cable as earthing lead connecting to main earthing dolly drawn in existing conduit complete all as specified and directed by Engineer-in-Charge

Supply and fixing Air curtain single phase 240V, 1400 RPM of length 115 mm complete all as specified. Make : ALMONARD / CROMPTON GREAVES

Material & Labour for sand filling as cushioning to under ground cables in layers including conslidation all as specified

Supply and laying brick covering as mechanical protection to underground cable using old size sub class 'B' bricks, laid flat size 230mm x 115mm x 75 mm with lenght of brick perpendicular to length of cable, all as specified and as directed.

Supply and lay cable XLPE insulated screened PVC bedded , galvanised steel strip or wire armoured ,electric power cable (heavy duty) 1100 Volts grade with Strand aluminium conductor of size 3.5 core 35 sq mm Complete (LT Panel to DB)

Supply and lay cable XLPE insulated screened PVC bedded , galvanised steel strip or wire armoured ,electric power cable (heavy duty) 1100 Volts grade with Strand aluminium conductor of size 3.5 core 50 sq mm Complete (Main Power House to LT Panel )

Material & labour for earthing galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr depth below normal ground level) with top edge of earth not less than 1.5 mtr below normal ground level connected to and including galvanized steel strip 32 mm x 6 mm as earth lead upto equipment by means of steel bolts, nuts, check nuts and washers, test point made of GI strip 40x8mm, 10cm long PCC 1:2:4, type B-1 in pit with precast RCC 1:2:4 type B-1 in cover reinforced with XPM not less than 4 Kg per Sqm with 40mm bore GI light grade protection pipe, 20mm bore GI medium grade watering pipe with funnel including charcoal, dust, salt, all as shown in electric plate No 3 of SSR Part-I (2009) Specifications, complete with necessary earth work in any type of soil, removal to a distance not exceeding 50 mtr including testing on completion, complete all as specified & directed.

Supply, Install Testing & Commissioning of self supporting totally enclosed double door at front, LT feeder piller compartmentalised design, dust and varmin proof of size 1000 mm(Height) x 1000 mm(Length) x 450 mm(Width) suitable for 440 Volt 3 phase 4 wire system made out of 3.15 mm thick CRCA sheet and built upon regid frame work having front and rear hinged doors with neoprence rubber gasket including danger plate, earthing strip point and, ventilation louvers at the rear side, bottom detachable gland plate complete with suitable size of Zinc/Cromium plated and nuts, bolts ;and washers etc. The pannel shall be synthetic enamelled painted and the control circuit diagram shall be with colour code solid conductor copper 1.5 sqmm cable for easy identification including incomming/outgoing cable holes at the bottom, complete after taking down the old unserviceable one. The Panel shall be emmbeded with 75 x 6 mm MS Angle Iron frame and to be grouted with PCC foundation (1:3:6 ) type C2 upto a height of 50 cm from normal ground level complete all as specified and directed by Engr in charge and comprising of the following :

Material and labour for cable route indicator made out of 6mm thick cast iron circular plate 6 mm thick with LT cable 1100 volts embossed and fixed to an angle iron of 40x40x6 mm with bolts, nuts and twin washers of length not less than 50cm long, embedded in PCC 1:3:6 type C1 using 20 mm grade stone aggregate of size 200 x 200 x 200 mm including painting to steel surface with one under and one finishing coat of synthetic enamel paint cover a coat of redoxide primer all as specified.

Material and labour for GI Pipe light grade 50 mm bore for cable protection as a guard pipe complete.

Material and labour for MCCB, 4 pole, TPN, 415 volts, 36 KA, 200 Amps housed in sheet steel enclosure including making incomming and outgoing cable connection and mounting the sheet steel enclosure on the existing panel board at substation all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out in all type of soil and disposal of excavated earth lead upto 50m and lift upto 1.5m, as directed by Engineer-in-Chagre

A K JAIN AND SONS (BID ID -3117847)

BALVINDER SINGH AND SONS (BID ID -3126786)