Construction of staff quarters for BDO CDPO and BEO Payindem Upper Siang

Amount

COST FOR 3 UNIT SH: SITE DEVELOPMENT

Earth work in excavationin all kinds of soil (excluding soil containing 50% or more os shingle or small size boulders upto 30cm size, saturated soil and rock) including banking in 20cm layera and braking clods, ramming and dressing up for the purpose of making embankments or filling up ground depressions, lead upto 50 m and lift upto 1.50m

Excavation in decomposed or soft rock without blasting i/c disposal of the same lead upto 50m and lift upto 1.50m

SH: BUILDING PORTION S.H.: Earth Work

Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Re-filling of Excavated earth in foundation

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

SH: CONCRETE WORK

Providing and laying in foundations and plinth cement concrete 1 : 4 : 8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering.

Providing and laying cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in: b) Walls including attached buttresses, pilasters and their caps and bases and string courses etc. up to floor two level.

SH: RCC WORK

Centring and shuttering including strutting, propping etc and removal of form work for : a)Foundation in plinth

b) Column, pillars, posts and struts etc.

c) Walls including attached buttresses, pilasters etc.

d) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : (b) M-20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

For RCC Column footing

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring, shuttering and reinforcement. (a) M 20 (1 cement :1.5 coarse sand :3 stone aggtt. 20mm nominal size)

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface (a) M 20 (1 cement :1.5 coarse sand :3 stone aggtt. 20mm nominal size)

Reinforcement of RCC work including bending, binding and placing in position complete. b) Cold twisted bars.

SH: BRICK WORK

Masonry with pre-cast cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) blocks in cement mortar 1 : 4 (1 cement : 4 fine sand) in foundations and plinth..

Extra for pre-cast cement concrete block masonry in superstructure above plinth level up to floor two level.

SH: WOOD WORK

Providing approved best available local wood (Class - B II) work in frames of doors, windows clerestory windows and other frames, wrought framed and fixed in position.

Providing best available local wood (Class - B II) work in frames of false ceiling, partitions and trusses etc, sawn and put up in position.

Providing and fixing panelled, glazed or panelled and glazed shutters for doors, windows and clerestory windows including necessary iron butt hinges with necessary screws. a) 35 mm thick best available local wood, class - B I

Providing and fixing best available local wood glazed shutters for doors, windows and clerestory window using 7.5 kg/Sq.m. (3 mm thick glass panes) including black enamelled MS butt hinges with necessary screws. a) 35 mm thick

Providing and fixing aluminium tower bolts (barrel type) with necessary screws etc complete. a) 250 x 10 mm

Providing and fixing Aluminium sliding door bolts, bright finished or and black enamelled with nuts and screws etc complete. a) 300 x 16 mm

Providing and fixing aluminium handles with necessary screws etc complete. a) 125 mm

Providing and fixing 40 x 3 mm flat iron hold fasts 40 cm long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30 x 10 x 15 cm in 1 : 3 : 6 (1 cement : 3 sand : 6 hard stone shingle 40 mm nominal size)

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

Providing and fixing MS Hooks and Eyes.

Providing and fixing 2.50 cm thick approved local wood eaves boards 23 cm wide with necessary mouldings etc.

Providing and fixing MS fan clamp type I of 16 mm dia MS bar bent to shape with hooked ends in RCC slabs during lying including painting the exposed portion of loop all as per standard design complete.

SH: FLOORING

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

Cement concrete flooring 1 : 2 : 4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement. a) 40 mm thick

SH: ROOFING

Providing corrugated G.I.sheet roofing fixed with galvanised iron J or L hooks, bolts & nuts 8 mm dia with bitumen and G.I. limpet washers or with G.I. limpet washers filled with white lead complete, excluding the cost of purlins, rafters and trusses. a) 0.63 mm thick GI sheet

Providing ridges or hips 60 cm overall in plain G.I. sheet fixed with galvanised iron J or L hooks, bolts and nuts 8 mm dia. G.I. limpet and bitumen washers complete.

Providing and fixing 4.0 mm thick asbestors plain sheet ceiling of approved quality with necessary nails etc.complete (frame work for base to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

Extra for making chamfered edges of beading.

SH: FINISHING

15 mm cement plaster 1 : 6 (1 cement : 6 fine sand) on the rough side of single or half brick wall.

12 mm cement plaster 1 : 6 (1 cement :6 fine sand).

Neat cement punning.

Painting two coats with oil type wood preservative of approved brand and manufacture on new work.

Applying priming coat with ready mixed pink primer of approved brand and manufacture on wood work complete.

Applying priming coat with ready mixed primer of approved brand and manufacture on steel work.

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

Painting two or more coats (excluding priming coat ) with superior ready mixed paint for wood work of approved brand and manufacture in all shades on new work to give an even shade.

Distempering (two or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

White washing with whiting on new work (three or more coats) to give even shade.

SH: MISCELLANEOUS

Making plinth protection 50 mm thick of cement concrete 1 : 3 : 6 (1 cement : 3 coarse sand : 6 stone aggregate using 20 mm nominal size) over 75 mm bed of stone ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including finsihing the top smooth.

SH: WATER SUPPLY

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work). a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work). c) 25 mm nominal bore

Providing and fixing brass bib cock of approved quality. a)15 mm nominal bore

Providing and fixing brass stop cock of approved quality. a) 15 mm nominal bore

b) 25 mm nominal bore

SH: SANITARY

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvan a) Long Pan patten WC Pan

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cu a) Flat back wash basin size 550x400 mm with a pair of 15 mm CP brass pillar taps of heavy quality.

TOILET REQUISITES:

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). 750 x 20mm size

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes. b) 75 mm dia

Providing and fixing sand cast iron trap of self cleadnsing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors. a) 100 mm inlet and 100 mm outlet Bath Room , Kitchen, W.C

SH: DRAINAGE

Construction of cement concrete drain 30 cm wide and 23 cm deep in cement concrete 1 : 3 : 6 (1 cement : 3 sand : 6 hard graded stone chips/shingle 40 mm and down gauge) 8 cm thick on sides and bottom and plastering on all exposed surfaces with 12 mm thick cement morter 1:3 (1 Cement:3 fine sand) including shuttering complete.

Providing laying and jointing glazed stone ware pipe grade 'A' with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. a) 100 mm dia SW pipes

c) 200 mm dia SW pipes

Providing and laying cement concrete 1 : 5 : 10 (1 cement : 5 lime sand : 10 graded stone aggregate 40 mm nominal size) all around SW Pipe including bed concrete 15 cm thick as per standard design. c) 200 mm dia SW pipes

Constructing brick masonry manhole with 2nd class bricks in cement mortar 1 : 5 (1 cement :5 fine sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 stone single 20 mm nominal size), foundation concrete 1 : 4 : 8 mix (1 cement : 4 coarse sand : 8 stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of net cement and making channels in cement concrete 1:2:4 mix( 1 cement : 2 coarse sand : 4 stone aggregate 20mm nominal size) neatly finished complete as per standard design. a) Inside size 90 x 80 cm and 45 cm deep including CI cover with frame (light duty) 455 x 610 mm internal dimensions total weight of cover and frame to be not less than 38 Kg (weight of cover and frame to be not less than 38 kg, (weight of cover 23 Kg and weight of frame 15 kg), cement concrete 1:4:8.

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete as per standard design.

SH: CHAIN LINK FENCING - 60 MTR.

Earth work in excavation in foundation and trenches etc. in all kinds of soil (excluding soil containing 50% or more of shingle or small size boulders upto 30 cm size, saturated soil and rock), lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning the stacked soil in 15 cm layers, when required, into plinth sides of foundation etc consolidating each deposited layer by ramming and watering and then disposing of all surplus soil as directed within a lead of 50m.

Providing and laying in foundations and plinth cement concrete 1:5:10 (1cement:5 sand:10graded stone aggregate 40mm nominal size) excluding the cost of centering and shuttering.

Providing and laying cement concrete 1:3:6 (1cement:3 sand:6 graded stone aggregate 20mm nominal size) excluding the cost of centering and shuttering in a)Foundations and Plinth

b)Wall including attached buttresses,pilasters and their caps and bases and string courses etc.upto floor two level.

Centering and Shuttering including strutting proping etc.and removal of form work for: a)Foundations and Plinth

b)Wall including attached buttresses,pilasters etc.

G.I.Chain link fencing 1.20m height and 15.00m length

M.S. Angle iron post 50 x 50 x 6mm @4.50Kg/m

Painting two or more coats (excluding priming coat) with superior ready mixed paint for steel work of approved brand and manufacture in all shades on new work to give an even shade.

ELECTRICAL INSTALLATIONS (Details for 3 Unit) POINT WIRING

Wiring for light point /fan point /exhaust fan point /wall fan/call bell point with 1.5 sq. mm. FRLS PVC insulated, copper conductor single core cable in surface/recessed medium class PVC Conduite with piano type switch, phenolic laminated sheet, suitable size MS box and Earthing point with 1.5 mm FRLS PVC insulated copper conductor single core cable required: Group-B

Wiring for light/ power plug with 2x4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 no. 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 2x4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 no. 4 sq.mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit / sub mains wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. a)2x2.5 sq.mm + 1x2.5 sq.mm earth wire.

b)4x10sq.mm + 2x10 sq.mm earth wire.

Supplying and fixing metal box of 150 mm x 75 mm x 60 mm deep ( nominal size ) on surfance or in recess with suitable size phenolic laminated sheet cover in the front including provinding and fixing 3 pin 5/6 amps socket outlet and 5/6 amps piano type switch, connections, painting etc. as required. ( For light plugs to be used only in non- residential buildings).

Supplying and fixing metal box of following size (nominal sizes) on surfance or in recess with suitable size phenolic laminated sheet cover in the front including painting etc. as required. ( For power plugs). a)150mm x 75mm x 60mm deep

Supplying and fixing of following sizes of medium class PVC conduit along with the accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required : 25 mm dia.

Installation, testing and commissioning of prewired, flourescent fittings/ CFL of all types, complete with all accessories and tube etc. directly on ceiling/wall, including connections with 1.5 sq.mm. PVC insulated, copper conductor, single core cable etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down roads of standard length (upto 30 cm) with 1.5 sq.mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Numbering of ceiling fan/exhaust fan/air circulator/flourescent fitting as required

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Earthing with G.I. earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.(but without charcoal or coke and salt) complete as required.

Supplying and laying 25mm x 5mm copper strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating with nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of brass nut bolt and spring washer spaced at 50mm).

Providing and fixing 25 mm x 5 mm G.I. strip on surface or in recess for connections etc. as required.

Supply the following Lighting fixtures including lamps at site. Rate shall include all taxes and duties, transportation etc. complete. a)1 x 40 watts Flourescent Light Fixture as per Bajaj Cat No. BJIE 136/140

c)48 " dia ( 1200 mm sweep ) ceiling fan .

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single pole

Supplying and fixing single pole, blanking plate in the existing MCB DB complete etc. as required.

SH: FURNITURE

Wooden Cot with Mosquito Net stand

Wooden Writing Table

Wooden Arm Chair

Water filter 25 ltr capacity

Plastic Moulded Chair

Meat Safe

Centre Table

Dining Table 4 Seater

Dining Chair

SH: M S GATE

M/s Gesar Enterprises

Er. Miss Purnima Nangkar

M/s Asum Engineering

Er. Genom Apang