Construction of 2x40 MVA 132KV AIS S/S Jagdishpur, Amethi on turnkey basis

Total Price for Supply of Equipments and Material and Light Luminaires S -1

Total Price for Handling, Erection, Testing & Commissioning Charges S - 2

Total Price for Civil Works S-3

Total Price for Electrical & Civil works ([S-1]+[S-2]+[S-3])

Seal of Company

Designation ……………

Name of Bidder

SCHEDULE- 1

FOR 2x40MVA, UPEIDA (IMLC) AIS 132/33 KV SUB-STATION JAGDISHPUR, AMETHI AGAINST SPECN. No. ESD-683

Transformer

STATION TRANSFORMER,250KVA,36/0.415KV

Circuit Breaker

SF6 CB,145KV,3150A,40KA

VCB,36KV,2000A,31.5KA

Current Transformer (CT)

CT 145KV 800-400-200/1A,(Polymer type) 3C,40/1,0.2S

CT 145KV,400-200-100/1A,(Polymer type) 3C,40/1,0.2S

Terminal CONNECTOR, for CT,145KV,TWIN PANTHER

JUNCTION BOX,CT,145KV

CT 36KV 800-400/1A,(Polymer type) 3C,0.2S (with Terminal Connector)

CT,36KV,400-200/1A,(Porcelean type) 2C,0.2S (with Terminal Connector)

36kV CT Junction Box

Potential Transformer (PT)

145 kV Potential Transformers 50 VA

Terminal connector for 145 kV PT

132 kV PT Junction Boxes

36kV Potential Transformer with terminal connector 50 VA

36kV PT Junction Box

Isolator

145kV 1250 Amp. Line Isolators with one earth switch (Motorised) without post insulator

145kV 1250 Amp, Bus Isolators without earth switch (Motorised) without post insulator

145kV 1250 Amp.Tandem Isolators (Motorised) without post insulator

36kV 1250 Amp,Line Isolators with Post Insulators with one earth switch

36kV1250 Amp. Bus Isolators with Post Insulators and without earth switch

36kV Drop Out Fuse Set with Post Insulator

Insulator

145kV Post Insulator

36KV Post Insulator

70kN Antifog Disc Insulators

Surge Arrestor

120 kV Polymer type Surge Arrestor

30 kV Polymer type Surge Arrestor

CRP & SAS ( as per Technical specification of SAS)

Rotational under frequency Relay Panel 145KV

132 kV T/F Control & Protection Panel for 40 MVA T/F

132 kV Simplex Feeder C&R Panel

132 kV Simplex type Bus Coupler Panel SAS

132 kV Transfer Bus Control Panel (TBC)

33kV Triple Feeder C&R Panel

SAS (complete set)

Optical fibre reqd. for SAS

Battery & battery charger

110 V, 200 AH Batteries complete Set lead acid

Battery Charger for 110V, 200AH Batteries

LT Switchgear

110 V DC Distribution Board

415 V AC Distribution Board

415 V AC Lighting DB

Bay Marshilling Kiosk

Capacitor Bank & its Accessories

2x5 MVAR, 33kV Capacitor Bank Unit along with following equipment

Simplex Type Control & Relay Panel for 33kV Capacitor Bank

VCB,36KV,2000A,31.5KA

SURGE ARRESTOR,30KV

3-Phase Reactor

CT,36KV,400-200/1A,2C,0.2S (with Terminal Connector)

JUNCTION BOX,CT,36KV

ISOLATOR,36KV,1250A,W E/S (LINE ISOLATOR WITH POST INSULATOR)

ISOLATOR,36KV,1250A,W/O E/S (BUS ISOLATOR WITH POST INSULATOR)

36kV NCT Ratio 5/1A

Terminal Connector for 36kV NCT

Junction Box for 36kV NCT

PT,3 PHASE,36KV

Terminal Connector for 3-Phase PT

1.1kV PVC FRLS Unarmoured Copper Control Cable

2 Core x 2.5 Sq.mm

4 Core x 2.5 Sq.mm

6 Core x 2.5 Sq.mm

10 Core x 2.5 Sq.mm

1.1kV PVC FRLS Unarmoured Aluminium Power Cable

3.5 Core x 400 Sq.mm

3.5 Core x 95 Sq.mm

3.5 Core x 50 Sq.mm

Structure & Earthing Materials

Lattice Type Galvanised Main & Auxiliary Structure with MS angles, channels, plates, nuts, bolts, step bolts, U bolts, spring washers, etc. and any other required materials

40mm MS Rod for Main Earthmat

40mm dia, 3 Mtr MS Earth Electrodes

Energy Meter(SAMAST)

3P4W interface energy meter (ABT) of 0.2S class

Metering Cubicle

Network switch-16 Port, (14Cu+2FO)

Data Concentrator(DCU)/Communication Gateway(IG)

LAN Cable (average one roll per S/s 300 Mtr)

PVC conduit pipe-3/4"

OFC cable armoured(6P) along with HDPE conduit pipe 32 mm

LIU(Line interfacing unit) with patch chord and any other accessories for fibre cable ( to be used for extending length of ETHERNET cables)

Switch Network 8 port, 6CU+2FO

Conductors

ACSR Moose

ACSR Panther

Hardware fittings

Single Tension Fittings Suitable for

ACSR Moose

ACSR Panther

Single Suspension Fittings Suitable for:

ACSR Moose

ACSR Panther

PG Clamps suitable for

Moose/ Moose

Moose /Panther

Panther / Panther

Bus Post Clamp suitable for

Panther

Twin Panther

Moose

Twin Moose

Fire fighting Equipment

Fire Extinguishe, Mech Foam 50 lit.

Fire Ext. Dry Chem, IS,2171/1985, 4.5KG

Fire Ext. CO2, ISA 2878/1986, 22.5KG

Fire Ext. CO2, ISA 2878/1986, 9 KG

Fire Ext. CO2, ISA 2878/1986, 4.5 KG

Supply of sand buckets as per tech. Specn.

Supply of sand buckets stand suitable for 10 nos. bucket as per tech. Specn.

Fire protection and alarm system comprising of smoke & heat type detectors for 132 kv S/s

100 kVA Silent type DG set confirming to latest MoEFCC/CPCB guidelines

GI perforated trays of various sizes for all cable trenches in switchyard, control room including fixing for 132 kV S/s

GI perforated cable tray (225/250 mm)

GI perforated cable tray (75 mm)

Lighting and Luminaires

Supply of Complete fitting of Street Light Luminairs with LED Lamp 110 to 130 Watt, with all accessories (make Philips/CGL/Bajaj) Confirming to IP:65

Supply of Complete fitting of Post Top Lantern with all accessories with LED Lamp 40 to 45 Watt (make Philips/CGL/Bajaj) Confirming to IP:65

Supply of 15W LED Lamp (make Philips/CGL/Bajaj)

Supply of Complete fittings of 18/20 Watt LED Tube Light (make Philips/CGL/Bajaj)

Tool & Plants

Thermovision Camera (640x480 px) SATIR/FLIR Make

10 kV Digital Insulation tester (Megger or equivalent make )

Digital Multimeter (4 1/2 digit) (Motvani or equivalent make )

Digital Clamp-on-meter (Digital, 0-300-600A)

Earthing/Discharge Rod having, 25 sq. mm. copper cable

Self Supported Aluminium Ladder as per specification

Cartweel mountaed Aluminium Ladder as per standard

BDV Testing kit

Tank Oil Storage, 20KL

Earthing resistance tester (4 terminor digital type)

Earth Fault detection meter

Fibre Optic Terminal equipment(FOTE) SDH( STM-16)

Fote Base Equipment 4 Directions

Fote Short Haul, STM-16, 1310nm SFP Transceiver - S16.1

Long Haul, STM-16, 1310nm SFP Transceiver- L-16.1

Long Haul, STM-16, 1550nm SFP Transceiver- L-16.2

E1 Interfaces (120 Ohm) ( 32 Interfaces with 2 Cards)

L2Etherner Interfaces 10/100 Base T (16 Interfaces with minimum 2 cards)

Fote Equipment cabinet for SDH and DTPC 2200mm (h) including 100mm base, w x d should be suitable for 19" or 23" Rack

Fote MDF (200 Pairs), mounted in cabinet

04 command standalone Digital Tele-Protection Cuupler (DTPC) fully equipped with necessary common cards power Supply Cards other Hardware accessories Connectors Cables Subtrack with E I path cords set of 04 etc.

CCTV System

CCTV System for 132 kV Substation

Air Conditioner (AC) Unit (Hitachi/LG/O'Gen/Daikin/Voltas/Bluestar make)

2 Ton , 5 Star,Split AC along with Stablizer (5KVA)

TOTAL

Seal of Company

Designation ……………

FOR 2x40MVA, UPEIDA (IMLC) AIS 132/33 KV SUB-STATION JAGDISHPUR, AMETHI AGAINST SPECN. No. ESD-683

SCHEDULE- 2

Transformer

EREC 40 MVA,132/33KV TRF

EREC 250KVA,33/0.4KV TRF

Circuit Breaker

EREC OF 145KV CB

EREC OF 36KV VCB

Current Transformer (CT)

EREC OF 145KV CT

EREC OF JB FOR 145KV CT

EREC OF 36KV CT

EREC OF JB FOR 36KV CT

Potential Transformer (PT)

EREC OF 145KV PT

EREC OF JB FOR 145KV PT

EREC OF 36KV PT

EREC OF JB FOR 36KV PT

Isolator

EREC OF 145KV LINE ISO W/1ES

EREC OF 145KV BUS ISO

EREC OF 145KV TANDEM ISO W/1ES

EREC OF 36KV LINE ISO

EREC OF 36KV BUS ISO

EREC OF 36KV DROP OUT FUSE SET

Post Insulator

EREC OF 145KV POST INSULATOR

EREC OF 36KV POST INSULATOR

Surge Arrester

EREC OF 120KV LIGHTNING ARRESTER / SURGE ARRESTOR (POLYMER TYPE)

EREC OF 30KV LIGHTNING ARRESTER / SURGE ARRESTOR (POLYMER TYPE)

CRP & SAS (as per Technical Specification of SAS)

EREC OF UNDER FREQUENCY RELAY PANEL

EREC OF 132KV RELAY/CONTROL PANEL PWR TRF

EREC OF RELAY/CONTROL PANEL TBC

EREC OF RELAY/CONTROL PANEL BUS COUPLER

EREC OF RELAY/CONTROL PANEL FOR FDR

EREC OF 33KV TRIPLE FDR CRP

EREC OF SAS PANEL

EREC OF OPTICAL FIBRE FOR SAS

Battery & Battery Charger

EREC OF 110V BATTERY SET

EREC OF 110/48V BATTERY CHARGER

LT Panels

EREC OF 110V DCDB

EREC OF 415V ACDB

EREC OF LIGHTING DIST BOARD

EREC OF BAY MARSHALLING KIOSK

Capacitor Bank & its Accessories

EREC OF COMPLETE 33KV CAPACITOR BANK 2X5MVAR IN ALL RESPECT

Cable

1.1 KV PVC FRLS Unarmoured Copper Control Cable

LAYING 2CX2.5SQMM UNARM CTRL CABLE including Terminations of cables (COMPLETE IN ALL RESPECT)

LAYING 4CX2.5SQMM UNARM CTRL CABLE including Terminations of cables (COMPLETE IN ALL RESPECT)

LAYING 6CX2.5SQMM UNARM CTRL CABLE including Terminations of cables (COMPLETE IN ALL RESPECT)

LAYING 10CX2.5SQMM UNARM CTRL CABLE including Terminations of cables (COMPLETE IN ALL RESPECT)

1.1 KV PVC FRLS Unarmoured Alluminium Power Cable

LAYING 3.5 core * 400 sq. mm including Terminations of cables (COMPLETE IN ALL RESPECT)

LAYING 3.5 core * 95 sq. mm including Terminations of cables (COMPLETE IN ALL RESPECT)

LAYING 3.5 core * 50 sq. mm including Terminations of cables (COMPLETE IN ALL RESPECT)

Structure & Earthing Material

EREC,STRUCTURES, MAIN/AUX, INCL ACCS: with MS angles, channels, plates, nuts, bolts, step bolts, U bolts, spring washers, etc. and any other required material

LAYG MS BAR 700MM-40MM DIA 40mm for Main Earthmat

LAY,ELECTRODE,MS ROUND,40MMX3M,BLW GND 40mm Dia MS Electrode (3 M Long)

FRESH EARTHG,W/FLAT,75X10MM

FRESH EARTHG,W/FLAT,50X6MM

FRESH EARTHG,W/FLAT,25X6MM

Energy Meter

EREC OF ABT ENERGY METER

EREC OF ABT ENERGY METERING PANEL with one main & one check rack

INSTALLATION,DCU/GATEWAY/ETC including installation of Network Switch-16 Port, (14Cu+2 FO with FO Communication module (industrial frade), LIU (Light Interfacing Unit) with patchcord & accessories, Network Switch-08 Port, Data Concentrator (DCU)/ Communication Gateway (IG), laying of Lan Cable, PVC Conduit Pipe-3/4, OFC Cable Armoured (6P), HDPE Conduit Pipe 32mm

Stringing of Conductors

Stringing of Bus bars comprising of Conductors Tension & Suspension stings complete with anti fog type disc insulators, tension & suspension clamps, PG clamps, Bus post clamps, connectors, earth wires and all other required material for

132 KV Main Bus I & II

132 KV Transfer Bus

132 KV Jack Bus for

Feeder

40 MVA Transformer

Bus Coupler

33 KV Main Bus

33 KV Auxilliary Bus

JUMPERING TRF & ASSOC. EQUIP. Baywise interconnection of equipments with specified conductors ( jumpering ) for complete substation including but not limited to: 1.40 MVA Transformer bay including 132 KV &33KV side bays 2. 132 KV Feeder Bays 3. 132 KV Bus Coupler Bay 4. 132 KV Transfer Bus Coupler Bay 5. 33 KV Feeder Bays 6. 33 KV Bus Coupler Bay 7. 33 KV Bay for station Transformer (COMPLETE IN ALL RESPECT)

Fire Fighting equipments

EREC OF FIRE FIGHTING SYSTEM (COMPLETE IN ALL RESPECT)

DG Set

EREC OF 100 KVA DG SET conforming to latest MoEFCC/CPCB guidelines

Cable Tray

INSTALL,TRAY,CABLE,INCL FABRICATION/ETC

FOTE Equipments

ERECTION/LAYING/T&C,STM-16,FOTE Erection of Fiber Optic Terminal Equipment (FOTE) SDH (STM-16) including but not limited to installation /erection of : 1. Base equipment suitable for 04 directions in subrack fully equipped with all necessary common cards, power supply cards, other hardware & accessories including 10 Nos. optical patch cords of lengths as per site requirements, DDF etc. with redundant CPU. 2. Optical Base Card for 04 directions (STM-16) 3. Short Haul & Long Haul 4. E1 Interfaces & L2 Etherner Interfaces 5. Equipment cabinet for SDH and DTPC 2200mm (Alongwith 110V to 48V DC-DC Converter) 06 VOIP Phone 7. MDF (200 Pairs), mounted in cabinet 8. 04 command standalone Digital Tele-Protection Coupler (DTPC) fully equipped with necessary common cards power Supply Cards other Hardware accessories Connectors Cables Subtrack with E I path cords set of 04 etc. (COMPLETE IN ALL RESPECT)

CCTV system complete in all respetcs

Air Conditioner (AC) Unit system complete in all respetcs

LIGHT LUMINAIRES

OUTDOOR LIGHTING

PERIFERY AND ROAD LIGHTING

Supply and fixing of steel round pole 9.0 mt long in 1:4:8 cement concrete with 40mm brick ballast in size of 450x450x1900 and plastering of 300mm length of concrete above ground level

Supply of junction box of size 280x225x150mm made of 16 SWG sheet with grey painting suitable for 2x4x6 C sq mm incoming cable & 2x4x6 C sq mm out going cable fitted with 3 Nos. HRC Fuse link of 5A, Cable glands, neutral link, terminal block etc. and Fixing of junction box on M.S. round pole with the help of M.S. Clamp

Fixing of complete fitting of light luminaries with LED Lamp 110 to 130 Watt at designated height on light pole including taking out cable from junction box to light fixtures from inside pole. cable terminations and it’s testing and commissioning and earthing with 12 No. SW GI Wire

Supply & fixing of GI pipe bend of 35mm dia 'B' class 2.5 meter long and bended at one end by quarter circle in 0.5 meter for cable entry to junction box fitted on steel round pole

Painting of M.S. Round pole with first quality Asian /Nerolec/Burger paint, one coat of Red Oxide primer and two coats of Aluminium paint.

Making 3 Nos. of strips of 450mm height from plinth with Post Office red colour in bottom & top and white colour in middle on each light pole of 150mm dia on M.S. Round pole and writing No. of pole.

SWITCHYARD LIGHTING

Supply of junction box of size 280x225x150mm made of 16 SWG sheet with grey painting suitable for 2x4x6 C Sqmm incoming cable & 2x4x6 C sqmm out going cable fitted with 3 Nos. HRC Fuse link of 5A, Cable glands, neutral link, terminal block and Fixing of junction box on Columns with the help of 50x6mm G.I. Clamp

Supply and fixing of GI pipe bend of 35mm dia 'B' class 2.0 meter long and bended at one end by quarter circle in 0.5 meter for cable entry to junction box fitted on column

Supply and fixing of Light bend of 50mm dia GI 'B' class pipe 1.5 meter long bended at 1 meter at an angle of 300 for 250W HPSV light in Switchyard.

Fixing of complete fitting of LED 110 to 130 Watt light luminaries at designated height on Column with the help of GI clamps & Light Bend cable terminations and it’s testing and commissioning and earthing with 12 No. SW GI Wire.

LAWN LIGHTING

Supply & fixing of 'B'type light pole 2.5M long and fixing of cable bend pipe & its concreting in the ratio of 1:2:4 with 20mm stone granite and cement concrete in the size of 500x300x300mm including excavation, back filling, curing etc. to complete the job

Supply of Junction Box of size 180x150x100mm made of 16 SWG steel with grey painted suitable for 2x2x6 C Sqmm cable fitted 2 Nos. HRC Fuse link of 5A & 1 No. Neutral link terminal block, cable glands etc and fixing of junction box on light pole with the help of M.S. clamps and then making plinth of size 225x300x300 in the ratio of 1:2:4 cement & coarse sand with 20mm granite with JB embedded in the plinth and the top surface of plinth being tapered from all four sides of plinth with 30mm height in the centre including all associated works of finishing, plastering etc.

Supply & fixing of 50mm dia GI pipe light pole of 'B' class quality

Supply & fixing of 'J' bend of 25mm dia GI pipe of 'B' class for cable entry

Assembling and fixing of complete fitting of post top lantern with LED Lamp 40 to 45 Watt over the light poles, cable terminations, testing & commissioning etc.

Making 3 Nos. of strips of 150mm height from plinth with Post Office red colour in bottom & top and white colour in middle on each light pole of 50mm dia

GATE LIGHTING

Supply & fixing of junction box of size 180x150x 100mm as specified above at si.no. C_2

Assembling and fixing of Complete fitting of post top lantern with LED Lamp 40 to 45 Watt with cable terminations, testing and ,commissioning

CABLE LAYING AND TERMINATIONS

Laying of 4cx2.5 sq mm copper control cable from control room to various point and for lawn lighting in excavated trench

Laying of 2cx2.5 sq mm Copper control cable for lighting in switchyard periphery, road etc. in excavated trench

Taking out above cable from junction box to light fittings fixed over the column by fixing GI clamps of 40x5mm flat with each crossed bracing on structures proper dressing etc

Excavation of trench of size 300 x 600 mm for laying of cable, putting ganga sand & Ist class bricks over the cable and then earth filling etc.

Supply & fixing of Cable marker made of cast iron

INDOOR LIGHTING FOR CONTROL ROOM AND STORE

Wiring for light point/fan point/ Exhaust Fan point/Call bell point with 3/22, 1.5mm2 PVC insulated copper conductor in PVC conduit concealed in wall with 2.24mm dia bare copper earth continuity wire & piano type switches etc. complete in all respect.

Wiring for 3 Pin 5A light plug point socked outlet on existing switch board with 3/22, 1.5mm2 PVC insulated copper conductor in PVC conduit concealed in wall with 2.24mm dia bare copper earth wire continuity along with piano type switch complete in all respect.

Supply and fixing of metal box of size 180x100x80mm deep in recess with suitable size of white laminated sheet cover in front including providing & fixing 3 pin 15 A socket & switch connection piano type with 7/22, 4.0mm2 PVC insulated copper conductor concealed in wall with 2.24mm dia bare copper earth wire continuity complete in all respect.

Supply & wiring of sub main with PVC insulated copper wire of size & no. as detailed below along with 2.24mm dia bare copper earth wire continuity in PVC conduit concealed in wall complete in all respect.

2x4mm2 with 1 No. earth wire

4x4mm2 with 2 No. earth wire

2x1.5mm2 with 1 No. earth wire

4x1.5mm2 with 2 No. earth wire

Supply & fixing of angle/button holder suitable for LED Lamps complete in all respect

Supply & fixing of Factory Wired in-door decorative luminairs with LED Lamp for ceiling mounting with mirror optic suitable for 2x20/2x18W LED complete in all respect of category 'A' (make Philips/CGL/Bajaj)

Supply & fixing of factory wired in-door decorative luminairs for surface mounting with oval polystyrene diffuser suitable for 1x20/1x18 W LED Lamp complete in all respect of category 'A' make.(make Philips/CGL/Bajaj)

Supply & Fixing of complete set of street light luminair with LED Lamp 110 to 130 Watt complete in all respect with integral control gear of category 'A' make.(make Philips/CGL/Bajaj)

Supply & fixing of factory wired LED light fitting suitable for 1x20W LED complete in all respect of category 'A' make.(make Philips/CGL/Bajaj)

Supply & Fixing of Fancy wall bracket 1x15W LED fittings

Supply & Fixing of decorative ceiling luminairs for 1x10W LED Lamp complete with round twin PVC insulated flexible cord, approved holder complete in all respect with bulb for DC lighting

Supply & Fixing of 1200mm ceiling Fan complete with electronic regulator with double ball bearing and approved colour of category 'A' make as approved by Engineer.

Supply & fixing of 18" Exhaust fan of category 'A' make as approved by the Engineer.

Supply & Fixing of 12" Fresh Air Fan of category 'A' make as approved by the Engineer

Supply & fixing of 6000 capacity Desert cooler of size made of 20 SWG galvanized sheet duly wired fitted with 18" Exhaust fan of cat 'A' make and vertical pump along with stand & other thing required to complete the jobs satisfactorily.

Supply and fixing of Four Pole Isolator of 60/63 A.

Supply and fixing of surface/flush mounting 8 ways SPN Distribution board with MCB complete in all respect.

Supply & fixing of Call bell of approved make on white laminated sheet board including making connection etc. complete in all respect.

Supply & Fixing of 600x800x8mm GI plate vertically for earthing with its top at least 3M below the ground level complete with 20mm dia GI pipe & funnel for watering and one earthing lead of one No. 8 to 10 SWG GI wire within 15mm dia GI pipe up to switch board 30cm square CI frame with hinged cover masonry housing alternate layer of charcoal/coke and salt at least 150mm thick alround etc as per direction of Engineer complete in all respect

Supply & Fixing of Distribution box 6 bay TPNDB with 100 Amp. Isolator and 18 No. SP MCB of different capacity Havells make.

TOTAL

Seal of Company

Designation ……………

FOR 2x40MVA, UPEIDA (IMLC) AIS 132/33 KV SUB-STATION JAGDISHPUR, AMETHI AGAINST SPECN. No. ESD-683

Name of Bidder:

SCHEDULE- 3

Bill of Quantity Construction of Main Gantry, Aux. Foundation, Cable Trenches, Transformer Foundation, Fire wall, Capacitor Bank, C.C. Road, Interlocking Tile Road, Culvert, Control Room Building, Committee Room, Store Building, Sump House, Chain link Fencing, Drain, Tube Well Boring, Water supply works, Park & Plantation, Turfing, Furniture, Earth Filling and Mis. Development Work at 132/33 KV Sub Station IMLC-JAGDISHPUR, Amethi. (SOR 05/2024)(Annexure-I)

Earth work in excavation all kinds of soil by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge.All kinds of soil.( 2.6.1)

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.(2.8.1)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.( 2.25(a))

Extra for all kinds of soil every additional lift of 1.5 m or part there of in excavation / banking excavated or stacked materials.( 2.26.1)

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.(2.27 )

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m for all kinds of soil.( 2.28.1)

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.(2.31)

Clearing grass and removal of the rubbish up to a distance of 50 m outside the periphery of the area cleared.(2.32 )

Providing and laying in position cement concrete of 1:1½:3 (1 Cement: 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - All work up to plinth level.( 4.1.2)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:5:10 (1 cement : 5 coarse sand (zone-III) derived from natural sources : 10 graded stone aggregate 40 mm nominal size derived from natural sources)

Providing and laying cement concrete in 1:1½:3 (1 cement : 1½ coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor five level, excluding the cost of centering, shuttering and finishing:.( 4.2.2)

Centering and shuttering including strutting, propping etc. and removal of form work for Foundations, footings, bases for columns ( 4.3.1)

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification.( 4.12)

Providing and laying 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :(5.1.2 )

Reinforced cement concrete work 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources) in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement :( 5.2.2)

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).( 5.3)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete, ( 5.9.1)

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.(5.9.2)

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies, Shelves (Cast in situ) and access platform(5.9.3 )

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers( 5.9.5)

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts( 5.9.6)

Centering and shuttering including strutting, propping etc. and removal of form for Weather shade, Chajjas, corbels etc., including edges( 5.9.19)

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured).Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)( 5.11.1)

Steel reinforcement for R.C.C. work Thermo-Mechanically Treated bars of grade Fe-500D or more including straightening, cutting, bending, placing in position and binding all complete plinth/above level.( 5.22.6)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections. (5.30 )

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:4 (1 cement : 4 coarse sand)( 6.1.1)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in Cement mortar 1:6 (1 cement : 6 coarse sand)(6.1.2 )

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand)( 6.4.1)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:6 (1 cement : 6 coarse sand)(6.4.2)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundations and plinth in cement mortar 1:4 (1 cement : 4 coarse sand)( 6.12.2)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level.Cement mortar 1:4 (1 cement :4 coarse sand)( 6.13.2)

Providing edge moulding to 18 mm thick Granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.( 8.3.2)

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick : Float glass panes 4 mm thick glass pane (weight not less than 10kg/sqm). (9.7.7.1)

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378):250x10 mm

Providing and fixing ISI marked oxidised M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete (Copper oxidised as per IS 1378):150x10 mm

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 250x10 mm(9.97.2 )

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete : 150x10 mm( 9.97.4)

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete : 125 mm( 9.100.1)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(CSI No. 10.1)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.( 10.2)

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6 mm angle iron and 3 mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using flats 30x6mm for diagonal braces and central cross piece ( 10.5.2)

Supplying and fixing rolling shutters 80x1.25 mm M.S. laths with 1.25 mm thick top cover of approved make, made of required size M.S. laths, interlocked together through their entire length and jointed together at the end by end locks, mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete, including the cost of providing and fixing necessary 27.5 cm long wire springs manufactured from high tensile steel wire of adequate strength conforming to IS: 4454 - part 1 and M.S. top cover of required thickness for rolling shutters.(10.6.1 )

Providing and fixing ball bearing for rolling shutters. ( 10.7)

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings,glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)( 10.11.1)

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.( 10.18)

Steel work welded in built up sections/ framed work in stringers, treads, landings etc. of stair cases, including use of chequered plate wherever required, all complete, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. (10.25.1 )

Steel work welded in built up sections/ framed work in gratings, frames, guard bar, ladder, railings, brackets, gates and similar works including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. (10.25.2 )

Dry brick on edge flooring in required pattern with bricks of class designation 7.5 on a bed of 12 mm mud mortar, including filling joints with Jamuna sand, with common burnt clay non modular bricks. (11.2 )

Providing and fixing glass strips 40 mm wide and 4 mm thick in joints of terrazo/ cement concrete floors. (11.13.1 )

Providing and fixing 10 mm thick acid and/or alkali resistant tiles in flooring on a bed of 10 mm thick mortar 1:4 (1 acid proof cement : 4 coarse sand) of approved make and colour using acid and/or alkali resisting mortar bedding, and joints filled with acid and/or alkali resisting cement as per IS : 4457, complete as per the direction of Engineer-in- Charge. (11.21.1.1 )

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete. (11.37 )

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. (11.37A )

Providing and laying Vitrified tiles in floor Double charge vitrified tile polished finish of size 600 x 600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily. (11.41A.1.1 )

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab colour of Black, Cherry/Ruby Red or equivalent (11.56.1 )

Providing and fixing 110 mm diameter on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. ( 12.41.2)

Providing and Fixing 15 mm thick densified tegular edged eco friendly light weight calcium silicate false ceiling tiles of approved texture of size 595 x 595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanised steel sections (galvanising @ 120 grams per sqm including both side) consisting of main ‘T’ runner suitably spaced at joints to get required length and of size 24x38 mm made from 0.33 mm thick (minimum) sheet, spaced 1200 mm centre to centre, and cross “T” of size 24x28 mm made out of 0.33 mm (Minimum) sheet, 1200 mm long spaced between main’T’ at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross ‘T’ of length 600 mm and size 24 x28 mm made of 0.33 mm thick (Minimum) sheet to be inter locked at middle of the 1200x 600 mm panel to from grid of size 600x600 mm, resting on periphery walls /partitions on a Perimeter wall angle pre-coated steel of size(24x24X3000 mm made of 0.40 mm thick (minimum) sheet with the help of rawl plugs at 450 mm centre to centre with 25 mm long dry wall screws @ 230 mm interval and laying 15 mm thick densified edges calicum silicate ceiling tiles of approved texture in the grid, including, cutting/ making opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc., wherever required. Main ‘T’ runners to be suspended from ceiling using G.I. slotted cleats of size 25x35x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm G.I. adjustable rods with galvanised steel level clips of size 85 x 30 x 0.8 mm, spaced at 1200 mm centre to centre along main ‘T’, bottom exposed with 24 mm of all Tsections shall be pre-painted with polyster baked paint, for all heights, as per specifications, drawings and as directed by Engineer-in-Charge.Note :- Only calcium silicate false ceiling area will be measured from wall to wall. No deduction shall be made for exposed frames/opening (cut outs) having area less than 0.30 sqm.The calcium silicate ceiling tile shall have NRC value of 0.50 (Minimum), light reflection > 85%, non- combustible as per B.S. 476 part IV, 100% humidity resistance and also having thermal conductivity <0.043 w/mK.( 12.53)

12 mm cement plaster (IN COARSE SAND) of mix 1:4 (1 cement: 4 coarse sand) ( 13.4.1)

12 mm cement plaster (IN COARSE SAND) of mix 1:6 (1 cement: 6 coarse sand) (13.4.2 )

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 4 coarse sand) ( 13.5.1)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:6 (1 cement: 6 coarse sand) (13.5.2 )

12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand)

15 mm cement plaster on rough side of single or half brick wall finished with a floating coat of neat cement of mix :1:3 (1 cement: 3 fine sand)

12 mm Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. ( 13.9.1)

20 mm Cement plaster 1:3 (1 cement: 3 coarse sand) finished with a floating coat of neat cement. ( 13.9.2)

6 mm cement plaster of mix :1:3 (1 cement : 3 fine sand)

Neat cement punning. (13.18 )

Extra for providing and mixing water proofing material in cement plaster work in proportion recommended by the manufacturers. ( 13.21)

White washing with lime to give an even shade : New work (three or more coats) ( 13.37.1)

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)(13.46.1 )

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture(13.62.1 )

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (13.80 )

Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound )(Two coat) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. (13.83.2 )

Supply of welded steel wire fabric of required width having rectangular mesh painted with two or more coats of enamel paint of approved shade over a coat of primer (Priming & Painting to be paid for separately). (16.15.2 )

Fencing with angle iron post placed at required distance embedded With G.I. barbed wire in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used.(16.18.1 )

Welded steel wire fabric fencing with posts of specified material and of standard design placed and embedded in cement concrete blocks 45x45x 60 cm of mix 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size), every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and struts embedded in cement concrete blocks 70x45x50 cm of the same mix, provided with welded steel wire fabric fixed between the posts fitted and fixed with G.I. staples on wooden plugs or tied to 6 mm bar nibs with G.I. binding wire (cost of posts, welded steel wire fabric, painting, earth work in excavation and concrete to be paid for separately). ( 16.20)

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.) (16.45 )

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 Meter openable length ( total length 90 m), having 50 nos rounds per 6 Meter length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 Kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ Meter (cost of M.S. angle, C.C. blocks shall be paid separately) (16.53 )

Providing and fixing G.I. wire of dia 4 mm chain link fabric fencing of required width in mesh size 50x50 mm including strengthening with 2 mm dia wire or nuts, bolts and washers as required complete as per the direction of Engineer-in-charge. (16.70.1 )

Providing and laying C.C. pavement of mix M-20 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-in-charge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately). (CSI16.75-16.76)

Construction of granular sub-base by providing with material conforming to Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25 Material conforming to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per specifications and directions of Engineer-in-Charge. (16.78.2 )

Providing and laying 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. (16.91.2 )

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required W.C. pan with ISI marked white solid plastic seat and lid ( 17.3.1)

Providing and fixing White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: ( 17.7.3)

Providing and fixing 610x460 mm bowl depth 200 mm Stainless Steel Kitchen sink without drain board ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : ( 17.10.2.2)

Providing and fixing 10 litre capacity - White P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete. (17.18.1 )

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. ( 17.23)

Providing and fixing 32 mm dia Flexible pipe P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. ( 17.28.2.1)

Providing and fixing 100 mm sand cast Iron grating for gully trap. ( 17.29 )

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (17.31 )

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors :100 mm inlet and 100 mm outlet Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905 (17.60.1.3)

Providing and fixing PTMT 600 mm long with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms. towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour ( 17.73.2)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work - Exposed on wall 20 mm dia nominal bore ( 18.10.2 )

Providing and fixing 15 mm dia nominal bore G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall :( 18.11.1)

Providing and fixing 20 mm dia nominal bore G.I. Pipes complete with G.I. fittings and clamps, i/c making good the walls etc. concealed pipe, including painting with anti corrosive bitumastic paint, cutting chases and making good the wall : ( 18.11.2 )

Providing and fixing 15 mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work ( 18.12.1)

Providing and fixing 20 mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work (18.12.2 )

Providing and fixing 25 mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work ( 18.12.3)

Providing and fixing 32 mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work ( 18.12.4 )

Providing and fixing 40 mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work ( 18.12.5)

Providing and fixing 50 mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work ( 18.12.6)

Providing and fixing 65 mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work ( 18.12.7)

Providing and fixing 80 mm dia nominal bore G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work ( 18.12.8)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 25 to 40 mm nominal bore ( 18.13.1)

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete : 50 to 80 mm nominal bore ( 18.13.2)

Providing and fixing brass bib cock of approved quality : 15 mm nominal bore (18.15.1)

Providing and fixing 15 mm dia brass stop cock of approved quality (18.16.1)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore (18.17.1)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 20 mm nominal bore ( 18.17.1A)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 32 mm nominal bore. ( 18.17.2)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 40 mm nominal bore (18.17.3 )

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm nominal bore (18.17.4 )

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 65 mm nominal bore (18.17.5)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :15 mm nominal bore (18.18.1)

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :20 mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :20 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :25 mm nominal bore Horizontal

Providing and fixing gun metal non- return valve of approved quality (screwed end) :50 mm nominal bore Horizontal

Providing and fixing 150 mm diameter C.P. brass shower rose with 15 or 20 mm inlet : ( 18.22.2)

Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all soils except ordinary hard rocks requiring blasting, including removing the casing pipe after the hand pump / tube well is lowered and tested :Up to 6 metres depth (18.42.1)

Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all soils except ordinary hard rocks requiring blasting, including removing the casing pipe after the hand pump / tube well is lowered and tested :Beyond 6 m and up to 12 m depth (18.42.2)

Boring with 100 mm diameter casing pipe for hand pump / tubewell, in all soils except ordinary hard rocks requiring blasting, including removing the casing pipe after the hand pump / tube well is lowered and tested :Beyond 12 m and up to 18 m depth (18.42.3)

Providing and placing in position filters of 40 mm diameter G.I. pipe with brass strainer of approved quality. (18.43)

Providing and fixing to filter and lowering to proper levels 40 mm G.I. pipe for tube well including cleaning and priming the tube well. (18.44)

Providing and placing in position hand pump of approved quality for 40 mm diameter G.I. pipe complete with all accessories. (18.45)

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. (18.48 )

Providing and fixing 15 mm nominal bore C.P. brass bib cock of approved quality conforming to IS:8931 : ( 18.49.1)

Providing and fixing 15 mm nominal bore C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing not less than 810 gms. (18.50.1 )

Providing and fixing15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. (18.51.1 )

Providing and fixing 15 mm nominal bore C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931. (18.52.1 )

Providing and fixing 15mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 ( 18.53.1)

Providing and fixing 15 mm nominal bore, 122mm long, weighing not less than 99 gms PTMT bib cock of approved quality and colour. ( 18.54.2)

Providing and fixing 15 mm nominal bore with 30cm length unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. (18.74.1 )

Supplying and fixing C.I. cover without frame for manholes 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg (19.18.2 )

Making soak pit 2.5 m diameter 3.0 Meter deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 (19.32.1 )

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.450 mm dia RCC pipes. (19.35.1)

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.600 mm dia RCC pipes. (19.35.2)

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C. pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete.900 mm dia RCC pipes. (19.35.3)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)( 21.1.1.2)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever requiredincluding cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of all fittings, EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron).( 21.1.2.2)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side(21.2.1 )

Providing and fixing float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm) glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):( 21.3.2)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. With stainless steel cover plate minimum 1.25 mm thickness complete as per the direction of Engineer-in-charge.(21.4.1 )

Filling the gap in between aluminium frame & adjacent RCC/ Brick/ Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete.Upto 5mm depth and 5 mm width

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete.

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge Powder coated minimum thickness 50 micron aluminium

Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/ Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag elastomeric PU sealant over backer rod of approved quality as per architectural drawings and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F & ISO 11600 Upto 5 mm depth and 5 mm width

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge :With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.All types of soil. 300 mm dia (23.1.1.1 )

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.All types of soil.300 mm dia (23.2.1.1 )

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.150 mm nominal size dia(23.3.2)

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.( 23.5)

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.( 23.6)

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer -in-charge.( 23.7 )

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge. (23.8 )

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge.100 mm nominal size dia having minimum wall thickness 5.00 mm ( 23.10.1)

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia having minimum wall thickness 5.00 mm (23.10.2 )

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge.100 mm nominal size dia (23.11.1 )

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted (having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer -in-charge. 150 mm nominal size dia ( 23.11.2)

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge. ( 23.12 )

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of 150 mm dia. ( 23.13.2)

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 100 mm clamp (23.14.1)

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 150 mm clamp (23.14.2)

Providing and fixing Bail plug/ Bottom plug 100 mm diaof required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). ( 23.15.1)

Providing and fixing Bail plug/ Bottom plug 150 mm diaof required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). ( 23.15.2)

Providing and fixing false ceiling at all heights with integral densified calcium silicate reinforced with fibre and natural filler false ceiling tiles of Size 595x595mm of approved texture, design and patterns as per CPWD Specification 2019, to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mmthick (galvanized @ 120 grams per sqm including both sides)comprising of main-T runners of size 24x38 mm of length 3000 mm,cross - T of size 24x32 mm of length 1200 mm and secondaryintermediate cross-T of size 24x32 mm of length 600mm to formgrid module of size 600 x 600 mm, suspended from ceiling usinggalvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 12x50 mm long dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 76x25x25x1.6 mm fixed with grid and Z cleat of size 25x37x25x1.6mm thick with precut hole on both 25mm flange to pierce into 12x50mm or even bigger size dash fastener if require, fixed with Glavanised iron perimeter wall angle or size 24x24x0.40 mm of length 3000 mm to be fixed on periphey wall / partition with the help of plastic rawl plugs at 450mm center to center and 40 mm long dry wall S.S screws. The workshall be carried out as per specifications, drawing and as per directionsof the Engineer-in-Charge.With 15 mm thick Tegular edged light weight calcium sliciate false ceiling tiles

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.Group C (DSR E&M 2022 1.10.3)( 27.01)

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. 3 pin 5/6 amp socket outlet (DSR E&M 2022 1.24.4)(27.02 )

Supplying and fixing of 20 mm of medium class PVC conduit along with accessories in surface/recess including junction box, cutting the wall and making good the same in case of recessed conduit as required. (DSR E&M 2022 1.21.1)( 27.03)

Supplying and fixing of 25 mm of medium class PVC conduit along with accessories in surface/recess including junction box,cutting the wall and making good the same in case of recessed conduit as required.(DSR E&M 2022 1.21.2)( 27.04)

Wiring for circuit/ submain wiring with 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.(DSR E&M 2022 1.14.2)( 27.05)

Wiring for circuit/ submain wiring with 2 X 4 sq. mm + 1 X 4 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.(DSR E&M 2022 1.14.3)( 27.06)

Wiring for circuit/ submain wiring with2 X 6 sq. mm + 1 X 6 sq. mm earth wire of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. (DSR E&M 2022 1.14.4)( 27.07)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.(DSR E&M 2022 5.6)(27.08 )

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.(DSR E&M 2022 5.12)( 27.09)

Supplying and fixing 5 amps to 32 amps rating,Single pole, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. (DSR E&M 2022 2.10.1)( 27.10 )

Supplying and fixing 63 amps, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.(DSR E&M 2022 2.12.2)( 27.11)

Supplying and fixing 40 amps, double pole, 240 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. (DSR E&M 2022 2.12.1)( 27.12)

Supplying and fixing 4 way (4 + 12), Double door, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) (DSR E&M 2022 2.4.1)( 27.13)

Supplying and fixing of 4 way (4 + 12), Double door surface/ recess mounting, vertical type, 415 volts, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 amps tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.)(DSR E&M 2022 2.5.1) ( 27.14)

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit along with 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.(DSR E&M 2022 1.12)( 27.15)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 1 or 2 Module (75mmX75mm)(DSR E&M 2022 1.27.1)( 27.16)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 3 Module (100mmX75mm)(DSR E&M 2022 1.27.2)( 27.17)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 4 Module (125mmX75mm)(DSR E&M 2022 1.27.3)( 27.18)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 6 Module (200mmX75mm)(DSR E&M 2022 1.27.4)( 27.19)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 8 Module (125mmX125mm)(DSR E&M 2022 1.27.5)( 27.20)

Supplying and fixing following size/ modules, GI box along with modular base & cover plate for modular switches in recess etc as required. 12 Module (200mmX150mm)(DSR E&M 2022 1.27.6)( 27.21)

Supplying and drawing following 3 x 2.5 sq. mm sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.(DSR E&M 2022 1.17.12) (27.22 )

Supplying and drawing following 3 x 4 sq. mm sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed steel/ PVC conduit as required.(DSR E&M 2022 1.17.21) ( 27.23)

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).(DSR Horticulture 2020 2.2) ( 28.02)

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in stacks will be reduced by 8% for payment)Screened through sieve of I.S. designation 20 mm : (DSR Horticulture 2020 2.4)( 28.04i)

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).(DSR Horticulture 2020 2.8) ( 28.08)

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge(DSR Horticulture 2020 2.9) ( 28.09)

Providing and displaying of Areca Palm having ht. 90 cm to 1.20 m with 4 to 5 suckers, well developed, fresh and healthy with lush green foliage in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.(DSR Horticulture 2020 3.18) (28.14 )

Providing and displaying of Brassia Variegated having ht. 30 cm to 45 cm, well developed with fresh and healthy foliage in 25 cm size of Earthen pot/Plastic pot. & as per direction of the officer-in-charge.(DSR Horticulture 2020 3.24)(28.17)

Providing Circular Cement Concrete pots of specified size, cast with cement concrete of nominal mix 1:2:4 (1 cement: 2 coarse sand: 4 graded stone aggregate 6 mm nominal size), reinforced with 7 Nos ( 3 nos horizontal & 4 nos vertical “ U “ shape) M.S. wires of 3.5 mm dia as per design, including required form work, finishing with cement punning on exposed surface, curing for specified period and stacking in required rows & height, all complete as per direction of Officer-in-charge. Top inside dia 30 cm, outer bottom dia 20 cm, total height 30 cm & with wall thickness of 25.4 mm (DSR Horticulture 2020 2.30.1) (28.18 )

Plantation of Trees, Shrubs, and Hedge at site i/c watering and removal of unserveiceable material's as per direction of officer in charge (excluding cast of plant & water) Hedge Plant/Ground cover (DSR Horticulture 2020 2.57)( 28.42iii)

Providing and Displaying Marigold jaffri orange/yellow/Russet colour well developed with fresh & healthy foliage with 40 to 50 flowers in bloom specimen plant 60 to 75 cm ht in 25 cm Earthen Pot/Plastic Pot and as perdirection ofthe officer-in-charge. (DSR Horticulture 2020 4.37) ( 28.48)

Providing and stacking of plant Mogra of height 25 to 30 cm., 2 to 3 branch in earthen pots of size 20 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.(DSR Horticulture 2020 4.88) (28.51 )

Providing and Displaying Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot, as per direction of the officer-in-charge.(DSR Horticulture 2020 4.93) ( 28.52)

Providing and Displaying Adenium Obesum grafted well developed with fresh & healthy 30 to 60 cm ht. in 25 cm size Earthen Pot/ Plastic Pot as per direction of the officer-in-charge.(DSR Horticulture 2020 5.5)(28.53)

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.(DSR Horticulture 2020 7.24)( 28.54)

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge. (DSR Horticulture 2020 7.5) ( 28.56)

Providing and stacking of Mangifera indica (Mango-grafted ) of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.(DSR Horticulture 2020 7.53) ( 28.57)

Providing and stacking of Polyalthia pendula (Ashok Pendula) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.(DSR Horticulture 2020 7.77) ( 28.61)

Providing and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara,Mohan,Scarlet Queen, Variegated, Glabra Formosa, Peruviana Odissi, Paratha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge. (DSR Horticulture 2020 9.4) ( 28.65)

Arranging and spreding 75 mm thick broken grit 20 mm (Granite stone) uniform for turfing over 100mm thick base course of C.C. In 1:4:8 (1cement:4coarse sand: 8, 40mm stone ballast) top finish by brooming of cement mortar 1:4(1cement: 4 Coarse sand) including supply of all materials, labour and tools and plants etc. required for proper completion. ( 29.02)

Supply and filling brick bat in soak pit including all labour,material and T&P etc complete. (for 01 soak pit)(29.05 )

Supplying & fixing 24 gauge annodized aluminium sheet of approved quality including cutting, wastage and fixing the same over the wooden door shutters with nails with all material, labour and T&P.( 29.06)

Supply of 28 mm. dia M.S. Anchor bolts (conforming to IS 266) 900 mm. long with base plate (75x75x6mm) welded with anchor bolts including its threading upto a length of 10cm. and also supply of a pair of galvanized standard nuts with threading including supply of 5 mm thick washer and cost of labour, material & T&P for proper completion of work. ( 29.13)

Fixing and grouting 28 mm and above dia bolts in proper alignment level and setout with help of a template complete including supply of all labour & T&P etc. required for proper completion of the work.(labour rates only) . ( 29.14)

Supply of 25 mm dia.M.S. Anchor bolts (conforming to IS-226) 500 mm long with base plate(50x50x6 mm)welded with anchor bolts,including its threading upto a length of 10cm. and galvanizing upto 15cm from top, also supply of a pair of galvanized standard nuts with threading including supply of 5mm thick washer and cost of labour material and T&P etc. required for proper completion of the work. (29.15 )

Fixing and grouting 25 mm and below dia M.S. Anchor bolt in proper alignment level and setout with the help of a template including supply of all labour T&P etc. reqd. for proper completion of the work. (labour rates only) . (29.16 )

S/F in position 90 lbs M.S. Rail for transformer plinth including cost of all labour, material and T&P etc. required for proper completion of the work. (29.19 )

Grouting of vertical or inclined post of pale/chain/security fencing in true level, alignment and in plumb or inclination as required, including cost of all labour, materials and T&P required for proper completion of work. ( Post and concrete for grouting shall be measured separately) ( 29.21)

Fixing and grouting of trench edging in proper level and alignment including cost of all labour, and T&P etc. required for proper completion of the work but excluding cost of C.C. (labour rates only). ( 29.22)

Fixing of template in position level and alignment for grouting of Anchor bolt in main gantry (labour rate only). (29.23 )

Fixing of template in position level and alignment for grouting of Anchor bolt in auxiliary structure. (labour rate only). (29.24 )

Fixing of cable trench racks in proper position and alignment including cost of all labour, material and T&Petc. required for proper completion of the work (Labour rate only). ( 29.25)

Providing (12x15) mm section groove in plaster including all material, labour and T&P etc. required for proper completion of the work. (29.33 )

Champering the edge of concrete in auxiliary structure, of size 25 mm wide in triangular section including all materials, labour & T&P etc complete. ( 29.34)

2.5 cm thick 1:1.5:3 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and T&P etc, required for proper completion of the work. without base CC ( 29.35)

4.0 cm thick 1:1.5:3 plain cement concrete floor with cement, approved coarse sand & 2cm graded approved stone ballast laid in panels finished with 3mm floating coat of neat cement or cement and marble dust in ratio of 5:1 as specified and removing any overlapping mortar at the joints of the panels if any and giving them a uniform finish including supply of all materials, labour and T&P etc, required for proper completion of the work. without base CC (29.36 )

Painting letters & number over cable trench cover or other places with the help of stencils including painting of base of 150 mm. dia of one coat of primer and two coats of superior quality synthetic enamel paint size of letter to be 60 mm. x 10 mm. including cost of all materials labour and T&P etc. required for proper completion of the work including placing of Trench covers in required position. (CSI No. 29.37)

Pre-Construction anti-termite treatment, by creating a barrier under and around the columns pits, foundation trenches, under floors, junctions of Walls & floors, around the external perimetre of building, expansion joints, surrounding of pipes and conduits etc. (Plinth area of the building at ground floor only shall be measured as per I.S. 6313 (Part II 1981))with Eldrine emulsifiable 0.2% concentration or any other approved material such as Heptachlore or chlordance will be used. The consumption of emulsion shall be (i) Foundation and masonary @ 5 Ltrs/Sqm, (ii) Back fills in immediate contact of foundation@ 7.5 Ltrs. / Sqm, (iii) Top surface of Plinth filling @ 5 Ltrs / Sqm, ( iv) Junction of walls & floors @ 7.5 Ltrs / Sqm, (v) Soil along external perimetre of building @ 7.5 Ltrs / Sqm (vi) under apron of the building @ 5 Ltrs. /Sqm. The rates includes cost of all materials, labour, equipments, T&P complete. ( 29.41)

Providing and fixing MS reducer 150x100mm for making tubewell assembly , including cost of all labour, materials and T&P required for assembly making and proper completion of work. ( 29.42a)

Supply and fixing support clamps for 40 mm column pipes made out of MS flats, pairs of bolt-nuts etc complete with all material, labour, T&P. (29.48b )

Transportation and installation of tube well drilling Rig m/c, compressure for development and other required equipments and accessories at site of work and dismentlling & taking them back after successful completion of the work including cleaning, levelling - dressing the site properly, also disposing off the surplus earth, silt, sand etc. ( 29.51)

Supply and installation of 5H.P. Kirloskar or equivalent make single stage, horizontal, self priming,three phase dewatering pumpset of specification Head 14/16 M, Discharge 13.6/10 LPS, solid handle size 15.5 mm, suction 80 mm, delivery 80 mm, RPM 1500 including cost of 80 mm dia G.I. pipe for suction (3M) and delivery (4.5 M). ( 29.52)

Supply & installation of electrical control panel of L&T / Havells or equivalent make for 1.5/2.00 H.P single phase submersible pumpset / pumpset containing contractor relay condenser. ( 29.54b )

Supply & installation of electrical control panel of L&T / Havells or equivalent make for or 5 H.P pump set three phase submersible pump / pumpset containing contractor relay condenser. ( 29.54d)

Supply & Installation of submersible pump 2 HP outlet 40mm dia. or more, Head 89/45, Discharge 2000/6000 LPH of K.S.B/ CALAMA. or eqt. make including cost of labour, T&P and material required for completion of work. (29.55c )

Supply & fixing of steel wire rope for submersible pump including cost of labour, T&P and material required for completion of work. (29.56 )

Placing of trench cover of all size in proper position including transportation from different places within the S/S area including all labour, T&P etc. required for proper completion of the work as per direction of Engineer - in - charge.

Providing and fixing of 200 mm dia PVC pipe of 6 Kg/sqcm with special such as Tee, bend, socket, elbow etc including supply of all labour,material,T & P etc complete required for proper completion of work. ( 29.90)

Providing and fixing of 150 mm dia PVC pipe of 6 Kg/sqcm with special such as Tee, bend, socket, elbow etc including supply of all labour,material,T & P etc complete required for proper completion of work. ( 29.91)

Providing and fixing soap dish chromium plated with brackets fixed to wooden cleats with brass screws including supply of all materials,labour and T&P etc.required for proper completion of the work. ( 29.108 )

Providing and laying 110 mm SWR, PVC ( Finolex or equivalent ) pipe including cost of excavation, C.C etc including its jointing and connection, all materials, labour and T&P etc. required for proper completion of the work. ( 29.109c)

Providing and fixing 110 mm SWR, PVC ( Finolex or equivalent ) Bends including cost of all materials, labour and T&P etc required for proper completion of the work. ( 29.110c)

Providing and fixing 110 mm SWR, PVC ( Finolex or equivalent ) Socket including cost of all materials, labour and T&P etc required for proper completion of the work. ( 29.112c)

S/F full way 63/65 mm dia Fire hydrant Gun Metal Gate Valve heavy quality including supply of all labour , material andT & P for proper completion of work. ( 29.117)

P/F Male & Female coupling 63/65 mm dia. Gun metal BSI marked confirming to IS:903 heavy quality including supply of all labour , material and T & P for proper completion of work. ( 29.118)

P/F Short Branch pipe Gun Metal BSI marked heavy quality including supply of all labour , material and T & P for proper completion of work. ( 29.119)

P/F 63 mm dia RLL Hose Pipe heavy quality having length 15.0 m including supply of all labour , material andT & P for proper completion of work. ( 29.120)

P/F MS Hose Box Single Door with stand for 15 mt RRL Hose heavy quality including supply of all labour , material andT & P for proper completion of work. ( 29.121)

Placing of 10 KL PVC Tank over slab of 6 m staging including supply of all labour , material andT & P for proper completion of work.(29.122)

Providing & laying of 2 mm thick epoxy flooring with chemcical (conpro EP 2P,conpro EP 36,conpro EPSL1) including all materials, labour & T&P etc. required for proper completion of work.(29.128 )

Supply and Fixing of 3 blade wall fan of Havells platina 400 mm or equivalent including all material, T&P etc required for proper completion of work as approved by engineer in charge.(29.132 )

Supply and Fixing of 5 blade Exhaust fan ventile air dx 225 mm of Havells or equivalent make including all material, T&P etc required for proper completion of work as approved by engineer in charge.(29.133 )

Supply and fixing of 36 Watt to 46 Watt indoor Recess mounting LED Square Fitting for Armstrong Ceiling having Powder coated die cast aluminium housing body with extended heat sink and diffuser of Special Polycarbonate meterial and driver set complete in all respect.( 29.134)

Supply and fixing of LED Tube Light batten fitting suitable for up to 1 X 22 watt LED tube light on surface complete in all respect.( 29.135)

Hydraulic Excavator of 1 CuM bucket+(10% Contractor preofit) (Material item no 51 Ch. 1)

Supply of executive office table size 1600x750x750 mm Particle board top Geeken(Model No. FGMNUMERO 0201171) or equivalent make as approved by E/I.(NSI)

Supply of executive office table size 1500x750x750 mm Particle board top Geeken(Model No. FGMNUMERO 0701182) or equivalent make as approved by E/I.(NSI)

Supply & fixing of high back revolving chair PP cushion arm ,gas lift nylon base leatherite tapestry Geeken(Model No FGAALTONA 100006) or equivalent make as approved by E/I (NSI) (J.E.room 01)

Supply & fixing of chair with PP seat back and Powder Coated Metal Frame Geeken (Model No FGCGB 40300544) or equivalent make as approved by E/I. (NSI)

Supply of steel almirah size 1830x900x450 mm Geeken(Model No FGAGMS 1000965) or equivalent make as approved by E/I. (NSI).

Supply and fixing steel rack size 1800x900x450 mm with 5 shelves multiflex Geeken(Model No FGAGMS 2001006) or equivalent make as approved by E/I.(NSI)

Supply and fixing double Bed size 2060x1980x930 mm Geeken (Model No. FGBHOSTEL1201864) or equivalent make as approved by E/I.(NSI)

Supply of matress of size 1900x900x125 mm of sleepwell or equivalent make as approved by E/I.(NSI)

Providing & Fixing of Three Seater Sofa made of wooden frame, SS pipe legs & seat back leatherite tapestry. size 1825x780x755 mm Geeken (Model No FGSHENLEY300299) or equivalent make as approved by E/I.(NSI) (Living room 01,Meeting room 01)

Providing & Fixing of one Seater Sofa made of wooden frame, SS pipe legs & seat back leatherite tapestry size 830x780x755 mm Geeken (Model No FGSHENLEY100245)or equivalent make as approved by E/I.(NSI) (Living room 02,Meeting room 02)

Supply of double bed sheet of size 2.74x2.74 m of Bombay dying make or equivalent make as approved by E/I.(NSI)

Supply of pillow of size 56x33x10 cm. of mass 1.5 kg minimum sleepwell make or equivalent make .NSI

Providing & fixing of center table (1200X600)MM made of SS pipe frame chrome finish with toughened glass top12 mm thick and lower glass 6 mm thick Geeken (Model No FGTALICE00690) or equivalent make as approved by E/I (NSI) (Living room 01)

Supply and fixing of blind stripe roller dim out Kazage make or equivalent with Haid rail and all material, T&P and labour etc required for proper completion of job as per direction & approved by Engineer-In-Charge. (NSI)

Total Rs.

Seal of Company

Designation ……………