Providing Internal External Electrification 1 No. 40KVA Diesel Generator set, 1No. 15 Persons capacity Stretcher Bed cum passenger lift and Air conditioning arrangements to additional building in Government Hospital at Ayikudi in Tenkasi District

Amount

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End )

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (6 points / Coil) Higher End

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe Concealed in wall and ceiling with PVC accessories with Module GI switch box in flush with wall with 6A one way module switch with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with suitable colour for Concealed PVC Light point / fan point (for electronic regulator) (5 points / Coil) Higher End ))

Supply and run of 1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in existing PVC rigid pipe Concealed in wall.

Wiring with 2 x1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC accessories with suitable Module GI switch box in flush with wall with 1 no.6A one way module switch and 1 no. 6A 3/2 pin module socket with module front plate with continuous earth wire connection of 1.5 sq.mm copper wire and making good of the concealed portion with painting of suitable colour for concealed PVC pipe Plug point (8 points / Coil) Higher End

Wiring with 2 x 1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with MS switch Box and 5A FT switch with painting of suitable colour continuous earth wire connection of 1.5 sq.mm copper wire for light point / fan point (for electronic regulator)

Wiring with 2 x 1.5 sq.mm. PVC insulated single core unsheathed FRLS copper conductor cable of 1100V grade in suitable heavy gauge MS conduit pipe on wall and ceiling with MS accessories with 150mm x 100mm x 75mm MS switch box for 5A 3 pin non interlocking flush type CS plug with painting of suitable colour with continuous earth wire connection of 1.5 sq.mm copper wire for open plug point

Supply and fixing of WT bulk head fitting with guard suitable with 7W / 9W LED bulb

Supply and fixing of 24W LED square type Surface mounting fitting with LED (Higher end) with PVC unsheathead FRLS copper leads from terminals to the fitting and necessary connection complete.

Supply and fixing of 4 Feet LED 20W Fitting with LED 20W tube (Higher End) complete with TW round blocks on wall or ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting

Supply and fixing of Batten holder (bakelite) with 9W LED lamp

Supply and fixing of 4 Feet LED 20W Fitting with LED 20W tube (Higher End) complete with conduit pipe suspension from the ceiling with PVC unsheathed FRLS copper leads from terminals to the fitting with tube

Supply and fixing of Twin box type 4' 20 W LED fitting (Higher End) with CRCA body complete with conduit pipe suspension from the ceiling with PVC unsheathed FRLS Copper leads from terminals to the fitting with 2 nos of 20 W LED tubes.

Supply and fixing of 48W LED street light fitting with LED (Higher end) with 32mm dia. GI pipe (class B) with 1 no.32 mm dia GI bend complete on the existing post/ on wall with PVC unsheathed FRLS copper leads with MS clamps and with painting .

Supply and fixing of 1200mm (48") sweep AC ceiling fan High speed complete with 2 module 100W fan step regulator (Higher end) with 300 mm down rod with fan clamp with side plates and cross arm of size 450mm (18")

Supply and fixing of 300mm (12") sweep (light duty) AC exhaust fan complete without provision of hole in the wall

Supply and fixing of louvers shutters arrangements for 300mm (12") sweep (light duty) AC exhaust fan

Supply and fixing of 3nos.6A two module socket , 1 no. 6/16A two module socket , 3 nos. 6A one module switch, 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 1 no.6/16A two module socket , 1 no. 16A one module switch with module cover plate (plastic) on suitable module concealed Box (GI ) in flush with wall with connections. Higher End

Supply and fixing of 32A Double pole MCB in sheet steel enclosure in flush with wall and making good of the concealed portion with earth connection.[The MCB and metal enclosure should be of Higher End.

Supply and fixing of 32A FP MCB in sheet steel enclosure in flush with wall and making good of the concealed portion with earth connection. [The MCB and metal enclosure should be with of Higher End]

Supply and fixing of 63A FP MCB in sheet steel enclosure in flush with wall and making good of the concealed portion with earth connection. [The MCB and metal enclosure should of Higher End]

Supply and fixing of 8 way single pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 32A DP MCB as incoming and 6 nos. 6A to 32A SP MCB as outgoing in flush with wall with earth connection only. [Higher End]

Supply and fixing of 7 segment 4 way triple pole neutral MCB distribution board in sheet steel enclosure double door type with metal door with IP 42 protection with 25A 4 pole MCB as incoming and 3Nos 25A DP RCCB as sub incomer and 12 Nos. 6 A to 10 A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection. (Higher End)

Supply and fixing of 4 way Horizontal Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 No 32A 4P MCB as incoming and 12 Nos 6A to 32A SP MCB as outgoing in flush with wall with Earth connection only. Higher End

Supply and fixing of 4 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB as incoming and,12 nos 32A SP MCB as outgoing on suitable angle iron frame on wall with earth connection only. Higher End

Supply and fixing of 8 way Vertical Triple pole and neutral MCB sheet steel enclosure distribution board with double door (metal) with 1 no. 63A 4P MCB as incoming and 6 nos. 32A TP MCB and 6 nos. 6A -32A SPMCB as outgoing in flush with wall and making good of the concealed portion with earth connection.

Supply and fixing of 8 way Vertical Triple pole and neutral MCCB sheet steel enclosure distribution board with double door (metal) with 1 no. 100A 4P MCCB as incoming with spreader terminals, 5 nos. 63A TP MCB and 3 nos. 32A TP MCBas outgoing in flush with wall and making good of the concealed portion with earth connection. Higher End

Supply and fixng of TNEB meter board suitable for 3 phase 100A service connection made up of suitable angle iron frame work of size 2 feet x 1-1/2 feet using angle iron of size 1-1/2" x 1-1/2" x 1/4" rigidly fixed on wall covered with hylem sheet of size 2 feet x 1-1/2 feet of 12mm thickness with necessary bolts and nuts supports and supply and fixing of 3 Nos. 100A fuse units (500V), 1 No. neutral link, copper earth flat of size 1" x 1/4" with inter connection of EB meter to fuse units by 16 Sq.mm PVC insulated copper wire with 100A FP RCCB with 30mA Sencitivity except AC type earth connection complete.(Higher End)

Supply and fixing of 100A TPN switch disconnector fuse units in sheet steel enclosure with HRC fuses double break on suitable angle iron frame work with MS cable entry boxes with Earth connection only.

Supply and fixing of 63 FPATS on suitable angle iron frame work with Earth connection only

Supply and fixing of 3 phase 100A aerial fuse unit for 3 nos 100A fuse units(500V) on suitable MS sheet covered with 6mm thick hylem sheet on suitable angle iron work the tapping pole with necessary clamps.

Supply and Run of 4 of 25 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade on 7/20 GI wire for service connection mains

Supply and Run of 4 of 25 sq.mm PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable dia GI pipe (class B ) suitably bent at both ends with necessary angle iron upright and end support for service connection mains

Supply and Run of 4 of 25 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 16 sq.mm copper wire and making good of the concealed portion.

Supply and fixing of 65mm (2 1/2 ") GI pipe Class B of 6 mtr length with 300mm x 300 mm x 6 mm MS base plate duly welded at the bottom with concreting of mansory pedastal for laying the cable.

Supply and laying of 3-1/2 x 50 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and clamping of 3-1/2 x 50 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3 1/2 x 50 sq.mm aluminium PVC LTUG armoured cable with earth connection.

Supply and providing cable end termination of 3-1/2 x 50 sq.mm. PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete

Supply and laying of 3-1/2 x 35 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and clamping of 3-1/2 x 35 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 3-1/2 x 35 sq.mm. aluminium PVC armoured LTUG cable with earth connection

Supply and providing cable end termination of 3-1/2 x 35 sq.mm. aluminium PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete.

Supply and run of 2 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with contiinuous earth wire connection of 6 sq.mm copper wire and making good of the concealed portion with suitable colour

Supply and run of 2 of 4 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection of 4 sq.mm copper wire and making good of the concealed portion with suitable colour

Supply and run of 4 of 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with continuous earth wire connection by 6 sq.mm copper wire and making good of the concealed portion with suitable colour

Supply and run of 4 x 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V on 7 / 20 GI bearer wire for service connection mains

Supply and run of 4 x 6 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100V grade in 32mm dia GI pipe (Class 'B') suitably bent at both ends with necessary angle iron up right and end supports for mains

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigd pipe concealed in wall and ceiling with continuous earth wire connection of 10 sq mm copper wire and making good of the concealed portion.

Earthing as per the ISI specification with an earth electrode of 2.1mt class 'B' GI pipe of dia not less than 40mm, with copper earth plate of size 125mm x 50mm x 6mm, with necessary funneling arrangements with necessary masonry work and with 38mm RCC cover slab for the brick masonry.

Supply and Run of 1 of No.8 SWG copper wire in suitable PVC rigid pipe on wall / floor / ground for earth connection

Supply and fixing of 3KVA Single Phase In & Single Phase out Online UPS of Microcontroller based High frequency and Double Conversion Online Technology with inbuilt isolation transformer system, LCD/ LED Display with suitable SMF battery to provide minimum 1 hour backup along with Powder coated MS Rack and interlink cables with following specifications: 1. Output Voltage Range : 208V/220V/230V /240V AC 2. Voltage THD (Linear Load) : ≤2% 3. Voltage THD (Non-Linear Load) : ≤4% 4. Current THD : < 10% 5. Overload : >110%, 30s turn to Bypass mode; >150% instant turn to Bypass mode 6. Short Circuit protection : 5 cycles turn off inverter, no transfer to Bypass, provide Alarm (AC mode) ; 5cycles turn off inverter, provide Alarm (Battery mode), Input fuse blown or breaker action 7. Waveform : Pure sinewave 8. Transfer time : (AC mode to Battery mode - Zero) (Inverter to bypass - <4ms) 9. Efficiency : 85% to 92% 10. Noise Level : less than 50dBA @ 1meter (with fan speed control) 11. Warranty : Two years on Electronics & one year on battery. (Microtek / Numeric make / Eq), (Battery make : Exide -6 Nos) The make and model should be approved by the departmental officers before used on work.

Supply and errection of 2.0 Ton 3 STAR rated on per BEE specification Split type Airconditioner (6000 K.cal/hr) GI sheet (ABS, HIPS plastic Fitted with Hermetically,scaled compressors operating refrigerant R-22/non CFC suitable (for wall mounting) confiriming to IS 1391 (part2) 92 (AMDT .1)(except power consumption Norms) suitable,operation on 230V,50HZ single phase AC supply and capable of performing the following function. (1) Cooling (2)Dehumidifying (3) Air circulation (4) Filtering (5) Heat pump for winter. The installation works for the above split type AC units including the following

a.Mounting/Filting Indoor & Outdoor units at their respective location.

b.Laying Refrigerant pipe line of required length connecting both units units after drilling hole/ holes in the wall,if required .Thckness of copper tubing shall not be less than 0.8 mm

c.Insulating the suction pipe with expanded polyethelene foam 5mm tubing.

d. Laying 25mm dia flexible pvc drain pipe to throw out the condensate water being formed in the indoor unit.

e. Leak testing the entire system unit

f. Charging Refrigerant gas in the unit

g.Suitable electric wiring & switch should be provided with in 3 meters of the location of unit. The Make should be approved by the departmental officers before used on work.

Supplying and installation of 5KVA electronic wide range automatic voltage stabilizer (V. Guard / equ. ) with input range of 140 - 270 V and out put voltage cut off and 3 minutes time delay relay with demonstration

Supply and laying of 5/8" and 3/8" copper pipe extra beyond 3 meter supplied with AC unit

Supply and fixing of MS stand for fixing outdoor unit

Supply and fixing of water drain pipe line (1” PVC Pipe)

Supply, Testing Commissioning and Handing over of 40 kVA Diesel Generator set with acoustic enclosure conforming to CPCB IV+ Norms and BIS Specifications with Standard Control Panel of 0.8 P.F. Three phase 415V/ 420 Volts, 50Hz, 1500 RPM CPCB Approved capacity developing 56 HP with acoustic enclosure water cooled clock wise rotating feed pump with 32KW/ 40KVA operating capacity brushless alternator close coupled underneath fuel tank standard safeties LLOP with stop solenoid battery with lead Electric start and vibration fitting and accessories and standard control panel as detailed below including transporting & unloading charges.

(A) Engine: Water cooled diesel engine suitable for Generator application conforming CPCBIV+ norms and IS standards with a shaft out put of 56 HP at 1500 RPM under NTP conditions. The Engine shall comprise the following standard fitting flexible coupling fly wheel, air cleaner, fan blower, radiator, water pump, fuel filter, lubricating oil filter, etc.

(B) 12 Volt Electronic starting Equipment: Complete with starter motor, dynamo, standard batteries with cable, flexible exhaust piping of 50cms length

(C) Engine Instrument Panel / Mounted: Starting push botton / starting key, lubricating oil, temperature gauge, lubricating oil pressure gauge, water temperature gauge, safety control for low lubricating oil, pressure, safety control for high water temperature, safety control for over speed, hour meter (mechnical) and RPM indicator, battery charging ammeter. The engine should be capable of providing 10% over load for one hour for every 11 hours continuous at full load.

D)ALTERNATOR: 40kVA/32kW Capacity of brushless alternator, AC 3 phase, 50Hz, 415/420V, 0.8 PF, 1500 RPM under NTP conditions, conforming to CPCB IV+ Norms.

E) STANDARD CONTROL PANEL : The standard control panel (cubical) should be vermin proof and dust proof best quality sheet steel of 16 SWG CRCA MS sheet and floor mounted with suitable hinged glass doors and enamel painted. The panel should be microprocessor based complete with suitable Square/ Rectangular copper bus bars with internal connections and with necessary cables and other accessories and with tapings for the incoming supply from the alternator and for the outgoing supply to the load and incorporating Suitable MCCB and HRC fuses, Set of control fuses, etc. with following facilities.

1. UNDER / OVER LIMIT i. High coolant Temperature ii. Low lube oil pressure iii. Over speed iv. Start fail v. Emergency stop vi. Over load 2. FAULT INDICATIONS: i. LLOP - Low Lub. oil pressure ii. HWT - High water temperature iii. OL - Over load iv. E.STOP - Emergency stop v. DG - Gen set ON vi. LOAD - ON

3.Metering & Protective relaying: i) Multi function Digital panel meter with the functions of Ammeter , Voltmeter, Frequency Meter, Power factor meter, KW meter, KWHr Meter .- 1No 2) Current transformers of suitable ratio. – Set of 3Nos. 3) Earth fault relay – 1No

1. The control panel should be complete with necessary fuses, cables, label, other accessories with neutral isolation arrangements. 2. The engine should trip for the following: a) Low lubricating oil pressure b) High water temperature c) Over speed

F.FUEL TANK minimum 100 litres fuel tank shall be fabricated out of 14 SWG CRCA MS sheet and is part of base frame. It is duly painted and fitted with inlet and outlet connections and mechanical fuel gauge. Fuel tank can be easily removed for cleaning or any maintenance.

G. Exhaust Gas Recirculation system arrangements as per CPCB IV+ norms as amended

H. BASE FRAME: Base frame should be fabricated with MS channel frame of rigidly welded construction for mounting of generaor set. The engine and alternator should be coupled by suitably designed diaphragm type flexible coupling with guard and mounted on the base frame with proper alignment.

I) ACOUSTIC ENCLOSURE: The Acoustic enclosure, Self standing weather proof Acoustic canopy conforming CPCBIV+ norms floor mounting type with modular construction with the provision to assemble and dismantle easily and designed to suit all weather condtions and compliance to IS standards.

Erection of acoustic enclosure suitable for 40KVA Diesel generator complete with all accessories as above and suitable supports etc. as approved by competent authority to suit updated CPCB norms.

J) Erection of generator set with proper alignment over the existing foundation.

K)Supply of manuals for operation & maintenance of DG set with warranty card etc. L) CEIG approval: Preparation of site plan physical layout, electrical line schematic Diagram 10 sets, getting drawing approval from CEIG preparation of complection report rectification report etc., arranging CEIG inspection and obtaining CEIG safety certificate, payment of CEIG inspection fees if necessary and preparation of one set of approval Drawing and copy of safety certificate in a neat frame work.

M)TESTING AND COMMISSIONING

After the installation of DG set on its foundation, the DG set should be tested and commissioned with first charging of lubrication oil to its level, first charging of battery and run the set for eight hours on full load test complete. The Genset engine and alternator make should be approved by department officials before used on work.

Providing suitable concrete foundation with plain cement concrete 1:2:4 using 20mm jelly for wearing coat including laying, compacting, finishing and curing etc., complete as per standard specifications and as directed by the departmental officers for 40kVA Genset

Supply and fixing of Automatic Electrical Water Heater with copper container, with Glass Wool / Puf Insulation with MS powder coated shell suitable for 25 Litres capacity / 1000W (Higher End) with ISI suitable for 230v AC supply,50 c/s with suitable clamp with 3 core flex wire but without plumpig work.

Design, Engineering, supply, fabrication, erection, testing, commissioning and handing over of 1 No. 15 persons capacity Stretcher cum passenger Gearless MRL lift with stainless steel panels disable friendly,micro processor baned controller,VVVF drive,fire rated doors and ARD,1M/S

Location : Government Hospital at Ayikudi

1. Type of lift : Stretcher cum passenger lift

2. Capacity of lift : 15 persons (1020 Kgs)

3. Speed : 1 .00 Mtr / Sec

4. Type of Drive: specific variable voltage variable frequency V3F drive with enhanced ride comfort and leveling functions. (MicroProcessor Based)

5. No. of floors: Ground +1 floor

6. Total Travel: 3.3m (approx)

7. Levelling Accuracy: High level accuracy with smooth and jerk free stopping.

8. Construction of Car: High quality stainless steel car with Neat hair line finish vinly flooring and false ceiling.

9. No. of landing entrance: 2 Nos

10. No. of car entrance: one in front only.

11. Car entrance door: power operated V3F drive side opening sliding stainless steel scratch proof door with hair line finish.

12. Landing entrance door: side opening stainless steel door with hair line finish with provision for emergency key opening at all landings.

13. Lift well existing: 1800mm (width) x 3000mm (depth) (As per IS 14665 Part I 2000)

14. Lift pit depth 1600mm

15. Car size: 1000mm (width) x 2400mm (Depth) as per IS 14665 (part I) – 2000)

16. Car clear opening: 800 mm width x 1900mm height (as per IS 14665) (part I) – 2000)

17. Over head height: CH+1900mm (as per IS 14665 part I – 2000)

18. Power supply: 400/440 V, 3 phase, 50 Cycles/sec A.C. supply for power and 230 V, 50 HZ, single phase, AC supply for light.

20. Car fittings: LED fittings & Regular (Circular)-Fan with comfortable ventilation inside the car.

21. Lift well: R.C.C. construction with brick masonry.

22. Indication: UP/Down digital direction and position indicator for all landing and in car (25mm height dot matrix digital floor position indicator scrolling type)

23. Emergency Alarm Bell: Battery operated alarm bell to be provided with Automatic charging device

24. Emergency light: Battery operated light to be provided with Automatic charging device in lift car.

25. Fire Man’s switch: To be provided at ground floor

26. Minor builders work: included in the scope.

27. Scaffolding: Included in the scope

28. Sill angles and facia plates: included in the scope.

29. Steel for lift machinery: Included in the scope.

30. Servicing and maintenance: Free comprehensive servicing and maintenance should be provided by lift contractor during the guarantee period of one year.

31. Automatic Rescue device: To facilitate the landing of the lift to the nearest floor at the time of power failure. This shall consists of suitable type battery system with charger, invertor, under voltage protection system etc., complete with all accessories.

32. Intercom (Push Type) in car panel and with provisio of push type intercom in machine room and ground floor entrance

33. Floor annunciator with music with announcement in both Tamil and English.

34. Special features:

a. Infra-red door sensor with full height screen

b. Full width half height rear panel mirror

c. Voltage stabilizer for circuit control.

d. Stainless Steel signal fixtures.

e. Vandal proof S.S. Button with S.S. cover

f. SS door frames for landing doors.

g. VF door operator.

h. Call Register signal

i. Stainless steel facia plate for car operating panel and landing fixtures.

j. On – Off switch for fan and light

k. over load warning indicator with audio announcement

35. Other standard features: Over speed governor, phase failure and phase reversal relay alarm bell, T. Guide brackets for car and counter weight, rubber padding under winding unit, motor of adequate capacity, electro magnetic brake with compression springs car safety gears buffer, electro mechanical door locks emergency key side supporting angles, motor over load protection devices final limit switch main suspension ropes counter weights lifting joint joist for mounting the machineries.

36. Guarantee: Guarantee for the materials and workmanship of equipments complete should be offered by lift firm for a period of not less than one year

37.Site testing in accordance with IS 14665 should be carried out at the time of handing over.

38. Supply of operation and maintenance manual with necessary tools for operation.

39.Lift License : Preparation of drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificates as per lift act. (G+1 floors) The make should be approved by the departmental officers before used on work

Supply and fixing of 65 mm dia. (2 -1/2") GI pipe (class B) of 6 metre length with 300mm x 300mm x 6mm MS base plate duly welded at the bottom with concreting with construction of masonary pedestal with suitable SMC box with door arrangement to house 6A SP MCB switch, 2/4 way connector on suitable hylem sheet and supply and fixing of 48W LED street light fitting with LED (Higher end) with 1 metre 32mm dia. GI pipe (class B) Complete with suitable MS clamps for LED street light fitting and SMC box with PVC unsheathed FRLS copper leads from SMC box to fitting and with painting of suitable colour .

Supply and laying of 2 x 16 sq.mm PVC armoured LTUG cable in a trench to be excavated at a depth of 0.75 metre putting 0.15 metre layer of sand and covering the cable completely with bricks and sand and refilling the earth to make good

Supply and clamping of 2 x 16 sq.mm. PVC LTUG armoured cable on post or on wall with MS clamps

Supply and fixing of brass cable gland for 2 x 16 sq.mm. PVC armoured LTUG cable with earth connection

Supply and fixing of 4way vertical triple pole and netral MCB sheet steel enclosure distribution board with double door (mental) with 1no. 63A 4P MCB as incoming and 3nos 32A TP MCB 3 nos 6A to 32A SP MCB as outgoing in flush with wall and making good of the concealed portion with earth connection Higher End

Supply and Run of 4 of 10 sq.mm. PVC insulated SC unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigd pipe on wall and ceiling with continuous earth wire connection of 10 sq.mm copper wire with painting of suitable colour.

SASTHA ELECTRICALS (BID ID -1478594)

ANNAI ELECTRICALS (BID ID -1478609)