Construction of recreation centre near A type Transit Accommodation

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge. All kinds of soil.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for mass concrete

Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Columns, Pillars, Piers, Abutments, Posts and Struts

Weather shade, Chajjas, corbels etc., including edges

Suspended floors, roofs, landings, balconies and access platform with water proof ply 12 mm thick

Edges of slabs and breaks in floors and walls Under 20 cm wide

Providing and laying (Concrete of M25 grade with minimum cement content of 330 kg /cum for All works upto plinth level) in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Providing and laying (Concrete of M25 grade with minimum cement content of 330 kg /cum for All works above plinth level upto floor V level) in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto and above plinth level with Thermo-Mechanically Treated bars of grade Fe-500D or more.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

12 mm cement plaster of mix : :6 (1 cement: 6 coarse sand)

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying Two Coats of Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour. Two Coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Supplying and fixing of First Class Hard wood (Sal wood) Plain, solid, straight chowkats and frames of doors & windows, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, etc., including the cost of all materials, labour, wastages, T&P etc., all complete as per specifications, drawings and as directed by E.I.C.

Providing and fixing ISI marked flush door shutters (30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws) conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.

Providing and fixing wire gauge shutters 30 mm thick of Second class teak wood with ISI marked M.S. pressed butt hinges bright finished of required size using S.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :

Two track two panels sliding door with Aluminium channel for roller track, wool pile, zinc alloy (zamak) powder coated handle on every panel along with multi-point locking system, adjustable nylon rollers with SS 304 body. Using R3 series with frame (55mm & above) x (40mm & above) & sash (30mm & above) x (74mm & above). (Height upto 2.5 metre).

Providing and fixing of factory made up to 2.55 m. high uPVC Casement door single panel with zinc alloy (zamak) 3D hinges, multi-point locking system with cylinder, zinc alloy (zamak) powder coated handles on both sides. Using R4 series with frame (64 mm & above) x (55mm & above) & sash (64 mm & above) x (100mm & above) (Height above 2.5 metre), comprises of Lead free U-PVC multichambered frame, sash and mulion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for series R1 & R2 Profile conforming to EN 12608 in any shape, colour & Design duly reinforced with galvanised mild steel section made of required shape and size as per CPWD Specifications; (WIRE MESH/GLAZING SHALL BE PAID SEPARATELY)

Providing and fixing 18 mm thick factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately)

Providing and fixing of factory made up to 1.20 m. high uPVC glazed /wire mesh windows comprises of Lead free U-PVC multichambered frame, sash and mulion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for series R1 & R2 Profile conforming to EN 12608 in any shape, colour & Design duly reinforced with galvanised mild steel section made of required shape and size as per CPWD Specifications; Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) with aluminium channel for roller track , wool pile, nylon rollers with SS-304 body Using R2 Series with frame (70 mm & above) X (40 mm and above) & both glazed and fly screen sash (25 mm & above) X (50 mm and above) with Zink alloy Zamak Powder coated touch lock with hook height up to 1.20 m. (WIRE MESH/GLAZING SHALL BE PAID SEPARATELY)

Providing and fixing of factory made up to 1.20 m. high uPVC glazed windows comprises of Lead free U-PVC multichambered frame, sash and mulion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for series R1 & R2 Profile conforming to EN 12608 in any shape, colour & Design duly reinforced with galvanised mild steel section made of required shape and size as per CPWD Specifications; Three track three panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70mm & above) x (40mm & above) & sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre). (WIRE MESH/GLAZING SHALL BE PAID SEPARATELY)

Providing and fixing factory made up to 0.90 m high uPVC Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash, single point locking zinc alloy (zamak) powder coated handles. Using R1 series with frame (33mm & above ) x (35mm & above) & sash /mullion (33mm & above) x (50mm & above). (Height upto 0.90 metre). comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture in windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and laying Vitrified tiles in floor Double charged Vitrified tiles Polish finished Size of Tile 1200 x 600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Providing and laying Vitrified tiles in floor Glazed Vitrified tiles Matt/Antiskid finish size of Tile 600 x 600 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge: Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes , having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge.

15 mm nominal dia Pipes

20 mm nominal dia Pipes

25 mm nominal dia Pipes

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with white seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing water closet squatting pan (Indian type W.C. pan White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:

Providing and fixing wash basin under counter with fixing accessories size 485x370x205mm shape rectangular, 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-

Providing and fixing white vitreous china flat back half stall urinal of size 580x380x350 mm with white PVC automatic flushing cistern, with fittings, standard size C.P. brass flush pipe, spreaders with unions and clamps (all in C.P. brass) with waste fitting as per IS : 2556, C.I. trap with outlet grating and other couplings in C.P. brass, including painting of fittings and cutting and making good the walls and floors wherever required : Single half stall urinal with 5 litre P.V.C. automatic flushing cistern

Providing and fixing Granite Stone of approved shade stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-incharge and finished smooth.

Providing and fixing 15mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Providing and fixing 15mm nominal bore C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931.

Providing and fixing 15mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing : Rectangular shape 1500x450 mm

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Finishing with Epoxy paint on steel work (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.

75 mm diamter

110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes

Single Tee with door 75x75x75 mm

Single Tee with door 110x110x110 mm

Single Tee without door 75x75x75 mm

Single Tee without door 110x110x110 mm

Bend 75 mm diameter

Bend 110 mm diameter

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.

75 mm diamter

110 mm diameter

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink ( Size 610x510 mm bowl depth 200 mm) as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Internal Electrification Make of Wire: Polycab/Finolex/L&T PVC Heavy duty Conduit: AKG/GM/CAP/Anchor Switch/socket Make: GM/Honeywell(MK)/Schneider Electric/Legrand (Blank plates shall be used as per site requirement)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit including all accessories such as bends, J.B,tees, ceiling rose, modular or angle holder (for light points),modular stepped type regulator etc. (for fan points) required for point wiring work with modular switch, modular plate with frame, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required. The pipe shall be laid concealed in wall; partially it may be flush to the wall as per site requirement.

Add to the above Item-1 for each addition on only light points on the same switch circuit including all materials required for such wiring work.

Wiring for twin light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit including all accessories such as bends, J.B,tees etc. , 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc as required.

Supply & making One (half point) with 5 pin, 6 Amps socket controlled by 6 Amps switch modular type on the same board with other switches with 1.5 sqmm, PVC. insulated,copper FRLS type conductor, multi stranded wire.

S & F of wiring for circuit/submains wiring alongwith earth wire with the following sizes of FRLS is PVC insulated copper conductor, single core cable in surface/ recessed as required. The pipe shall be laid concealed in wall; partially it may be flush to the wall as per site requirement. Make of Wire: Polycab/Finolex/L&T/Havells PVC Heavy duty Conduit: AKG/GM/CAP/Anchor

2 x 1.5 sq. mm (Red/Yellow/Blue) + 1x1.5 sq. mm earth wire (Green Color)

2 x 4.0 sq. mm (Red/Yellow/Blue) + 1x4 sq. mm earth wire (Green Color)

1x1.5 Sq mm Inverter wire (White Color)

Supply & making One independent domestic power point with 5 pin, 6/16A or 20A (for AC) modular socket controlled by 16/20 Amp or 25A (for AC) SP MCB modular type, with 4.0 sqmm P.V.C. insulated, copper FRLS conductor, multi stranded wire 1100/660 Volts grade in heavy duty P.V.C. pipe of including all accessories required for making power point/AC point such as modular cover plate with frame, P.V.C. pipe accessories, suitable size G.I. Box etc. The pipe shall be laid as per site requirement i.e. it may be concealed in floor/wall or flush to the wall. 2.5 sq.mm PVC insulated, single strand, copper FRLS wire shall be used in pipe with others wires for earthing of complete point wiring. Make: Havells/L&T/Crompton/Siemens

Supply and fixing of 18W circular type ceiling downlight with ABS housing with integral electronic LED driver with die-cast aluminium heat sink and white finish polycarbinate ring for holding the diffuser and make on junction box connection & testing. Make: Crompton/Philips/GM/Wipro/Osram

Supply & installation of LED Light Fitting, 4 feet x 34-38 watt twin T-8 LED tube complete fitting to be installed on ceiling or hanging from ceiling by m.s pipe/suspension wire or fixed on wall with all necessary fixing materials and arrangement. The work also includes connection from ceiling rose to fitting with twin core, white color flat flexible cable 1100/660 Volts grade. All material required for the work shall be supplied by the contractor. The work shall be done as per direction of engineer incharge. Make: Crompton/Philips/GM/Wipro/Osram

Supply and fixing 400 mm., RPM-1325,Sweep-400mm, metal blades and air delivery of 5500-6500 CMH wall fans of Crompton/Havells/Khaitan/Usha make. The work also includes connection from ceiling rose to fitting with twin core, white color flat wire of 1100/660 Volts grade. All material required for the work shall be supplied by the contractor. Make: Orient/Khaitan/Crompton/ Havells/Usha

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated premium decorative ceiling fan with BLDC motor , class of insulation: B, 3/4 nos. metallic finish blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote and electronic regulator unit for speed control suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required. Make: USHA/Atomberg/Orient/Luxaire/Havells/Crompton

Supply and installation of indoor type LED mirror with warm white color light with clamps and integrated LED as per following specifications:- Finish- Chrome Material- Chrome plated MS with PC diffuser Color rendering index- not more than 80 Lumen- 1000 Lm IP44, Warranty- 1 Year Premium reputed make Sample to be submitted for finalization.

Supply and installation of recess mounting 36 watt-40 watt LED luminaire of size 2 feet x 2 feet complete fitting. The work must be done as per direction of Engineer-In-Charge. The work also includes connection from ceiling rose to fitting with twin core cable, 1100/660 Volts grade make:- Polycab/Finolex /Havells. All material required for the work shall be supplied by the contractor. Warranty card of fitting duly filled and stamped by dealer is to be submitted to engineer incharge. The work shall be done as per direction of engineer incharge. Make: Crompton/Philips/GM/Wipro/Osram

Supply & fixing of heavy duty fresh air fan size 12", 220V, 50hz make Havells/Khaitan/Crompton/Orient complete in all respect (blades, frame and louvers) as per direction of EIC. (Metal body) Make: USHA/Atomberg/Orient/Luxaire/Havells/Crompton

Supply & fixing of heavy duty fresh air fan size 12", 220V, 50hz, Copper winding make Havells/Khaitan/Crompton/Orient complete in all respect (blades, frame and louvers) as per direction of EIC. (Sturdy Plastic Body) Make: USHA/Atomberg/Orient/Luxaire/Havells/Crompton

External Electrification DISTRIBUTION BOARDS/MCB/Isolator (MAKE:- L&T/Siemens/Schneider/Legrand/Hager)

Supply & Installation of new feeder pillar box outdoor type double door IP67 protected, vermin and weather proof made out of 14 SWG thick CRCA sheet including canopy type roof 15 cm extended in all side and two part hinged door in front side with knobs closing the front side door gasket arrangement and back side fixed with Nut, bolts and gasket, including provision of one set of aluminium busbar 250A rating for phase and 125 A for neutral fixed on DMC/SMC insulator with RYB Black colour code with heat shrinkable PVC sleeves and holes in bus bar strip and provision of suitable cable gland for cable entry including two coat of powder quoted paint complete and installation on PCC foundation with following: 1. Incoming:- Switch Fuse unit 250A rating with HRC fuses Make: L&T/Siemens/Schneider with 250A changeover switch 2. Outgoing: 06 nos. of 32A & 06 Nos. of 63A busbar mounted bakelite fuse base per phase complete Make: L&T/Siemens/Schneider 4. Phase indicating lamps for RYB on Each incomming/outgoing 5. Digital Multifunction meter of L&T/Secure/Risabh make for measurement of Volatge/ampere/power factor/KVA/KWH/MD. Note: Drawing of feeder pillar shall be get approved before fabrication work and making of foundation for installation work is in the scope of supplier. Work is to be done as per the direction of Engineer- In-Charge.

Supply and fixing of TP&N distribution board with Double Door 6 way per phase (LDB), with supply and fixing of following MCBs C-Curve and Isolator Legrand/Havells/L&T make, making connection and testing as per direction of EIC . Make: Legrand/Havells/Hager/L&T/Schneider/Siemens

Supply and fixing of TP&N distribution board with Double Door 6 way per phase (PDB), with supply and fixing of following MCBs C-Curve and Isolator Legrand/Havells/L&T make, making connection and testing as per direction of EIC . Make: Legrand/Havells/Hager/L&T/Schneider/Siemens

Supply, laying(underground), connection and testing of under noted size of aluminium conductor, XLPE insulated, PVC sheathed, steel armoured 1100 volts grade power distribution cables conforming to IS7098 part I 1988, by digging earth 85+/- 5cm depth, 25 cm width and supply & laying adequate sand and new class 'II' bricks for protection of cable, filling earth, leveling etc as per standard code of practice as per direction of EIC. Make Havells/Finolex/Polycab/Gloster

(i) 3.5 C X 120 sq.mm.

(iii) 4 C X 25 sq. mm.

(iii) 4 C X 6 sq. mm.

Making End Termination of 1100 V grade XLPE insulated and PVC sheathed armoured Aluminium conductor cable of following sizes with Supply & Fixing of Lugs & Glands as per direction of EIC. (make: Raychem)

Supply of UL listed CPRI tested maintenance free copper bonded earth rod of 3.048 m. having diameter of 17.2 mm with 254 micron copper bonding tested 45kA peak short-circuit current with clamp made of stainless steel for terminating cable/flat conductor. Earth enhancing material (PROCEM) compound (electrical resistivity 0.018 ohm metre) 25 kg tested for LEACHING and TCLP with NABL accredited LAB. The systems is conforming to IS3043, IS/IEC62305, IEC61643-5-54,UL467,the rod has to be tested for dimension, marking, tensile strength, salt mist, coating thickness, electrical resistivity test before and after corosion test etc. as per IEC 62561-2. Chamber inspection pit made up of PP material can bear 60kN load. Set consists of following BoM:- 1. Earth rod of 3 metre length having the dia of 17.2 mm 2. PROCEM 12.5 (25 Kg.) 3. Universal SS clamp 4. Pit cover

Supply and laying of 6 SWG GI wire for earth connection to MCB DB. The work includes bending, cutting, connecting etc. as per site requirement. The wire shall be properly supported. Complete job. Work is to be done as per the direction of engineer in charge.

Supply and laying of GI strip 25*5mm for earth pit connection to pedestal DB. The work includes bending, cutting, connecting etc. as per site requirement. The wire shall be properly supported. Complete job. Work is to be done as per the direction of engineer in charge.

Supply and fixing LED street light fitting 70W 230V AC with high pressure die cast Aluminium housing and heat resistant complete with driver, rod for fitting, lamp brackets with impact and corrosion resistant including thermal resistant in multiple optics complete with IP67 protection complete. Make: Havells/OSRAM/Philips/Crompton/Wipro

Supply & installation of Insect killer/Fly Catcher (power not more than 60W), wall fitted, with twin tubes with removable catchment tray

Supply, installation, testing and commissioning of 5 star rated inverter type High Wall Split Type Air Conditioner (single phase) for cooling on eco-friendly refrigerant gas with cordless remote, indoor & outdoor units complete, MS Stand for outdoor. Capacity: 1.5 TR Warranty on PCB: 05 Years Warranty on Compressor: 10 Years Warranty on ODU Casing: 05 Years

Total ( A)

Above

HAL-AD/9904/4619/CE/2024

Construction of recreation centre near A type Transit Accommodation

Description

Name of the Individual / Firm / Company: * Mandatory

Type of ownership Pvt. Ltd./ Proprietorship/Partnership/ Public limited/ Govt. Agencies/ Trust

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc.,

Address for correspondence:

Contact details

Intending parties having credentials as mentioned below may participate in e-tendering. The pre-qualification requirements for the works are as under :-

List of similar works executed in the past 7 years with value, schedule period of completion reasons for delay in completion if any and salient features of works, with documentary evidence of satisfactory completion.

PAN No.:

Constitution and legal status i.e. Proof of proprietary/Partnership firm or company & authorised person for receiving or signing the documents to be submitted.

Goods and Service Tax ID No.

SAC (Service Accounting code) along with the tax structure.

Income Tax Returns for the last three years

Annual turnover for the last five years.

Plant & Machinery details for the work.

Proposed work completion schedule in the form of bar-chart and monthwise billing plans.

Value of work on hand as on date of submission of tender also indicating the stipulated period of completion (required for bid capacity also) with following format:-

Bank Balance Statement for the last thee months.

Overdraft facilities available with the agencies.

Balance sheet for the last five years.

List of supervisor/ technical staff/

Bank account details such as account no., name of account holder, name and address of the bank, IFSC code duly certified by the bank along with cancelled cheque as a document of proof shall be attached.

Registered Contractor

Tenderer or its associate should posses electrical license under class ‘A’ category for execution of electrical works. The bidder shall submit the valid document i.e. license copy issued from the competent authority/ agency along with the tender document. In case, if license is expired at the time of submission of document, the bidder shall give an undertaking that renewed license will be furnished before execution of electrical works. Further the bidder will be responsible for all the contractual obligations with HAL.

Average annual financial turn over during the last 3 years, ending 31st March 2022 of the previous financial year [ should not be less than 30% of Amount put to tender]

EMD of Rs.159400.00

Latest Solvency Certificate issued from Nationalized/ scheduled Bank issued and NOT before 12 months from the last date of Tender submission

Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Latest work experience certificate may be uploaded]

(i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost.

(ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost.

(iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender.

Details of person holding the power of Attorney (If different from contact person)

Bid Capacity (i) The necessary documents to be submitted along with the technical bid (Technical bid ) Part-I in order to work out Bid Capacity as mentioned in Assessed available bid capacity as per NIT (ii) Assessed available bid capacity : The construction agencies who meet the minimum qualifying criteria shall be qualified only if their available bid capacity is more than the total estimated project/ package cost. The available bid capacity of a construction agency may be calculated as under :- Assessed available bid capacity = AXNX2-B, where N = Number of years prescribed for completion of subject project/ contract (indicate contract period N years) A = Maximum value of works executed in any one year during last five years at current price level, to work out value of work executed during previous years at current price level a weightage of 10% per year should be applied. B = Value at current price level of existing commitment and ongoing works to be completed in the next N years.

DECLARATION I

DECLARATION II

DECLARATION III