ADDN/ ALTN AND SPECIAL REPAIRS TO CERTAIN SINGLE OFFICER LIVING ACCN AT CME UNDER GE CME KHADKI

Amount

Dismantling of single layer Mangalore Pattern roof tile laid dry complete all as specified and as directed by Engineer-in-Charge.

Dismantling of single layer Mangalore Pattern roof tile laid and bedded in lime or cement mortar complete all as specified and as directed by Engineer-in-Charge

Dismantling battens for tiles, shingles etc, of any size including tilting fillets spacing exc 15 cm complete all as specified and as directed by Engineer-in-Charge.

Dismantling timber scantlings 40 sqcm and over in section, in any position unframed work complete all as specified and as directed by Engineer-in-Charge

Dismantling Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and as directed by Engineer-in-Charge

S&F Pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet Manglore pattern 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 in roof covering fixed with self tapping screws complete all as specified & directed by Engineer-in-Charge.

S&F Pre-painted Galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as per IS 15965: 2012 as wall cladding to wall, fixed with self tapping screws as in ridges, hips, valley, gutters etc. complete all as specified and as directed by Engineer-in-Charge

S & F hot rolled medium and high tensile structural steel of Fe-410W grade E 250 quality A conforming to IS 2062: 2011 as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. complete all as specified and as directed by Engineer-in-Charge

S & F hot rolled medium and high tensile structural steel of grade E 250 quality C conforming to IS 2062: 2011 as in rolled sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates complete all as specified and as directed by Engineer-in-Charge

M & L for preparation of new or previously untreated surfaces of iron of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engineer-in-Charge.

Dismantling water tanks and removing to store capacity exc 500 & n.exc 1000 litres complete all as specified and as directed by Engineer-in-Charge.

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in new or old position.Cleaning and removing all scale and dirt, etc, from tanks and from mouths of circulating pipes, Capacity of tanks exc 500 litres and not exc 1000 litres etc. complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete (un-reinforced) in roof/floors other than ground level beam, stair case, landing, chajjas and similar items including water proofing treatment in any layers and removing the same out side MD land complete all as specified and as directed by Engineer-in-Charge.

M&L for 25 mm thick , PCC M-15 grade (Nominal Mix) using 20 mm graded stone aggregate as in levelling course to match the undulations of roof and in coping , roof kerbs, fins including benching etc complete all as specified and as directed by Engineer-in-Charge.

M&L 10 mm thick screed bed in CM 1:3 mixed with water proofing compound of approved make over RCC roof slab/chajjas and vertical surface ,finished even and smooth by using steel trowel complete all as specified and as directed by Engineer-in-Charge.

M&L for applying a layer of blown grade bitumen 85/25 @ 1.2 Kg/Sqm conforming to IS : 702 and APP based polymeric membrane minimum weighing 3.50 kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 160 gm/sqm) laid over primed surface including bituminous primer conforming to IS-3384-1965 applied @ 0.3 litre/ Sqm by torch application complete all as specified and as directed by Engineer-in-Charge.

Supply only liquid water proofing compound

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing debris / rubbish out side MD land complete all as specified and as directed by Engineer-in-Charge.

Demolition of cement concrete(unreinforced ) in ground floors and pavings not exceeding 15cm thickness(below or above ground level) and removing debris / rubbish out side MD land complete all as specified and as directed by Engineer-in-Charge.

M&L 75mm thick PCC M-7.5 grade (Nominal Mix) using using 40mm graded stone aggregate as in sub base etc complete all as specified and directed

M & L for 25 mm thick PCC M-15 grade (Nominal Mix) using 12.5 graded stone aggregate as in base of floors complete all as specified and as directed by Engineer-in-Charge.

S&F Vitrified Ceramic coloured tiles 8-10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but n.exc 0.74 sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile etc complete all as specified and as directed by Engineer-in-Charge. Note : Screed bed or bedding layer shall be measured and paid separately under relevant item of this BOQ.

S&F Vitrified Ceramic coloured tiles 8-10 mm thick (square/ rectangular) polished, area of each tiles exc 0.36 sqm but not exceeding 0.74 sqm, in skirting etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile etc complete all as specified and as directed by Engineer-in-Charge. Note : Backing coat shall be measured and paid separately under relevant item of this BOQ.

S&F Non - skid Ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile etc complete all as specified and as directed by Engineer-in-Charge. Note : Screed bed or bedding layer shall be measured and paid separately under relevant item of this BOQ.

S&F Non skid Ceramic tiles 8 to 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.18sqm but not exc 0.38 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match etc complete as directed. Note : Screed bed or bedding layer shall be measured and paid separately under relevant item of this BOQ.

M&L for 15 mm thick screed bed or bedding layer in CM 1:6 for laying tiles etc complete all as specified and as directed by Engineer-in-Charge.

M& L for rendering 10mm thick in cement mortar 1:4 as in backing coat for laying tiles etc complete all as specified and directed

M&L glazed ceramic coloured tiles on vertical surface 350mmx450mmx7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match with colour of tile complete all as specified and directed, Note : Backing coat shall be measured and paid separately under relevant item of this BOQ.

Dismantling stone slab and tiles of any description and thickness as in floor including cement mortar bedding and rubbish off the premises complete all as specified and as directed by Engineer-in-Charge.

M&L coloured chequered cement concrete tiles glossy type 30cm x 30cm x 25mm thick set pointed with neat cement slurry with grey cement and pigment in floors over and including 15mm thick screed bed in CM 1:4 complete all as specified .

M&L 18-20mm thick machine cut machine polished kota stone slab flooring laid and pointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and laid over and including 20 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

All as per item No 31 above but in riser of steps, skirting, dado and pillar and jointed with grey cement to match the shade of kota stone complete and laid over and including 10mm thick rendering in CM 1:3 as in backing coat complete all as specified and as directed by Engineer-in-Charge.

M&L 18- 20 mm thick machine cut Granite slab bedded and jointed with grey cement and including pointing in white cement 1:2 using marble dust with admixture of pigment to match the shade including cutting , polishing and laid over and including 10mm thick screed bed in CM 1:4 in steps, jambs, pillars, window - cills, cooking platforms etc and the like complete all as specified and as directed..

M&L 20-25mm thick machine cut cuddappah stone slab laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing and laid over and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

Rounding to edges of stone slabs , such as in steps, cooking platform, and other similar situation complete all as specified and as directed by Engineer-in-Charge.

Taking up or down 15mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit all as directed.

Taking up or down 20mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit all as directed.

Taking up or down 25mm bore steel water tubing & connections, including cleaning for refixing or offering credit as per schedule of credit all as directed.

Supplying & fixing to walls and ceiling 15mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & fixing to walls and ceiling 20mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Supplying & fixing to walls and ceiling 25mm nominal bore, medium grade, galvanised coated steel tube conforming to IS 1239 (Part-1): 2004 including all fittings conforming to IS 1239 (Part-2): 2011 complete all as specified and as directed.

Refixing old steel tubing and connection of 15 mm dia in new or old position walls, ceiling, floor etc with new fittings complete all as directed.

Refixing old steel tubing and connection of 20 mm dia in new or old position walls, ceiling, floor etc with new fittings complete all as directed.

S & F in repairs table top vitreous china wash hand basin 480 mm dia including CI bracket, 15mm dia polythene connection, 32mm dia chromium plated (CP) waste coupling chain and plug waste filling union and 32mm dia PVC waste pipe 90cm long, all necessary inlet outlet connections complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe)including seat cover complete all as specified and directed

S&F in repair 10 litre capacity PVC valve less, symphonic action type flushing cistern, low level, white, with inlet ball valve, float and handle including bracket and 32mm dia flush pipe of polyethylene of low or high density for low level cistern complete all as specified and as directed by Engineer-in-Charge.

S&F Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) including spreader etc. Complete

S&F in repair brass chromium plated two way bib cock fancy type, 15mm bore ( min Wt. 550 grams) of approved make by EIC/ GE etc. Complete all as specified and as directed.

S&F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F PVC connection 15mm size with PTMT nuts of length 450mm complete

S&F in repair 15mm fancy type bib tap, chromium plated with crutch or butterfly handle, screwed down , screwed for iron pipe or for brass ferrule complete all as specified and directed

S&F in repair 15mm dia stop valve chromium plated fancy type screwed down high pressure with crutch or butterfly handle screwed both end for iron pipe or for union complete all as specified and as directed by Engineer-in-Charge.

M&L 25mm thick cement concrete M-15 grade (Nominal Mix) using 20mm graded aggregate) as in floor of bathroom mixed with WPC as per manufacturer instruction complete all as specified and as directed by Engineer-in-Charge. Note: WPC shall be measured and paid separately under relevant item this BOQ

Supplied only integral WPC

Cutting chase, pining in making good to facings where required & pointing in cement mortar 1:3 to ends etc or edges of landings, steps cills,sunshades, shelves,lintels,etc and cutting chases for concealed water tubing and making good, cutting n.exc. 10cm girth in brick walls all as directed.

M&L cutting hole in stone walls exc one brick but not exc 150 sqm superficial area for any purpose and making good dismantled position in cement mortar 1:3 or cement concrete M-15 grade (Nominal Mix)using 20mm graded stone aggregate as required complete all as specified and directed by Engineer-in Charge.

S&F in repair 75mm PVC(SWR) pipes Type B single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 110mm PVC(SWR) pipes type B single socketed in any length with rubber ring joints fixed to walls complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 75mm PVC(SWR) bend any radius complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 110mm PVC(SWR) bend any radius complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 75mm PVC(SWR) junction single(single T) equal or unequal complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 110mm PVC(SWR) junction single(single T) equal or unequal complete all as specified and as directed by Engineer-in-Charge.

M&L in repair 75mm PVC(SWR) floor trap with grating including jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge.

M&L in repair 110mm PVC(SWR) floor trap with grating including jointing with solvent cement complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 75mm PVC(SWR) vent cowl complete all as specified and as directed by Engineer-in-Charge.

S&F in repair 110mm PVC(SWR) vent cowl complete all as specified and as directed by Engineer-in-Charge.

S&F in repair Brass chromium plated tubular towel rail, 20mm dia , D type 60cm long between flanges complete all as specified and as directed by Engineer-in-Charge.

S&F in repairs sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with stain steel bracket guard and railing 60 cm long etc. complete all as specified and as directed.

S& F in repair Soap dish holder complete as specified and directed by Engr-in-Charge.

S&F in repairs Stainless steel, Toilet paper holder, box type

S&F in repairs Brass CP long body Wash basin mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed. Note :- The mixer shall be of single lever.

S&F in repairs Brass CP mixer for mixing hot & cold water screwed down for15 mm size iron pipe and fixed

Taking down chowkat or frames with shutter(without taking off shutters from the frames) not exc 1.5 sqm each and removing from site complete all as specified and directed.

Taking down chowkat or frames with shutter(without taking off shutters from the frames) exc 1.5 sqm and n.exc 4 sqm complete all as specified and as directed by Engineer-in-Charge.

S&F 2nd class hard wood plain solid straight chowkhats and frames, wrought, framed rebated on the solid rounded or chamferred,put together with glue pinned at joints complete all as specified and as directed by Engineer-in-Charge.

S&F 30mm thick flush shutter, solid core construction, with block board core and both face is covered with decorative face veneer with lipping/frame to match complete all as specified and as directed by Engineer-in-Charge.

S& fixed 2nd class hard wood 35 mm thick made glazed and skeleton shutters open rebated and prepared to receive glass, gauze,etc. (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass,etc, size of members of shutters as specified in SSR Part-1, Section 8, clause 8.24 (a)complete all as specified and as directed by Engineer-in-Charge.

S& fixed factory made plain framed panelled shutters 35mm thick of 2nd class hard wood (any number of panels) with panels of timber flat/glass on both sides feather edges or panel of 9mm BWP commercial ply over 12mm thick veneered panticle board with commercial face veneers fixed to chowkhat . The size of rail and stile as per IS : 1003 (Part-1), kiln seasoned and chemically pressure treated complete all as specified and as directed by Engineer-in-Charge.

M&L for preparing new or previously untreated surface of wood of any description, not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engineer-in-Charge.

M&L for Preparing old Wood and Wood Based Surfaces of any description, over 10cm width or girth and applying one Coats of Synthetic enamel Paint (First quality) complete all as specified and as directed by Engineer-in-Charge.

M&L preparing old Steel and Iron Surfaces of any descriptions, over 10cm in width or girth and applying one Coats of Synthetic enamel Paint , complete all as specified and as directed.

M & L mild Steel works as in bands straps, hold fasts, grills etc, conforming to IS-2062-2006 (Fe-290), embedded portion duly painted with bituminous paint and sanded, complete all as specified.

M & L preparing surface of iron and treating small articles such as stop, covers, gully grating, holdfasts, end of posts area exc 0.1 Sqm each complete all as specified and as directed by Engineer-in-Charge.

M&L for providing Cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate as in copings, bed plates, fixing of hold fasts and other similar works and the like incl weathering, slightly rounded or chamfered angles and throating as directed incl use and waste of necessary form work complete all as specified and as directed by Engineer-in-Charge.

S & F powder coated ( minimum thickness of powder coating shall not be less than 50 microns of approved colour ) Aluminium sliding windows three track with two glass shutters using 4 mm thick glass tinted and one shutter with stainless steel wire gauge wire cloth 0.31mm nominal dia of wire and width of aperture 1.61mm, using Aluminium powder coated sect, Aluminium cleat, PVC track, bearing, handle lock rubber beading, etc complete Note Size of aluminium sections are as under :- (i) Three track top & vertical – Jindal main – 2010 Section No 20621. (ii) Three track bottom - Jindal main – 2010 Section No 20620. (iii) Shutter vertical section - Jindal main – 2010 Section No 20606. (iv) Shutter top & bottom - Jindal main – 2010 Section No 20604 (v) Shutter vertical middle (interlock) - Jindal main – 2010 Section No 20605. Note: 4 mm thick glass tinted and stainless steel wire cloth 0.31mm nominal dia of wire and width of aperture 1.61mm shall be deemed to be included in unit rate quoted

S & F powder coated ( minimum thickness of powder coating shall not be less than 50 microns of approved colour ) ventilators partly fix and partly lowered of aluminium section designed DG-2762 (40 mm x 32 mm x1.5 mm thick) (wt 0.668 kg/mtr) frame and DG-2763 and middle section of designed DG-2763 (40 mm x 32 mm x 1.5 mm thick) (wt 0.654 kg/mtr), middle section DG-2546 (17.27 mm x 17.15 mm x 1.22 mm thick) (wt 0.124 kg/mtr) including 5 mm thick pinheaded figured glass louvers with blades of 100 mm heavy duty including with aluminium lever handle fixed panel shall be provided with and including 5 mm thick pin headed figured glass including all necessary rubber packing, anodized aluminium snap beading fixed with minimum 6 Nos of suitable size galvanised screws with PVC plug etc complete all as specified and as directed by Engineer-in-Charge.

S&F framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

S & F solid PVC door frame of size 50mm x 47mm made out of 5 mm plain colour PVC sheet reinforced with M.S. square tube etc all as specified and as directed.

M&L Factory Made Solid PVC Moulded Door Shutters 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design 2mm thick 3D wood grain Moulded PVC sheet polyurethane painted on the front face & 2mm plain colour PVC sheet on back face complete all as specified and as directed.

M&L for 18mm Veneered decorative plywood, grade 1 (with BWR resin) with decorative face veneers on both faces fixed with screws to timber frame work

M&L Extra over rates of block board or veneered particle board for external teak wood 18/19mm lipping 6mm thick fixed with nails

S&F 150mm hasp and staple, mild steel, wire type stove enamelled black, including bolt to hinge plate and fixed with screw.complete all as specified and as directed by Engineer-in-Charge.

S&F Mild steel butt hinges medium weight , cold rolled, 100mm, ISI marked, complete all as specified and as directed by Engineer-in-Charge.

M&L Aluminum anodiesd barrel tower bolts of size 200 mm of extruded section complete all as specified and as directed by Engineer-in-Charge.

S&F 150 mm long aluminium anodised handles of extruded section complete all as specified and as directed by Engineer-in-Charge.

S&F 300mm long Aluminium alloy, anodised , sliding door bolt with hasp , staple,(bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts of extruded sections or cast-aluminium alloy complete all as specified and as directed by Engineer-in-Charge.

S&F Mild steel 300mm ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and as directed by Engineer-in-Charge.

S&F galvanised mild steel wire cloth 0.56mm nominal dia of wire and width of aperture 1.18mm & fixed with tinned tacks or galvanised wire staples complete all as specified and as directed.

Demolition of brick or stone/boulder masonry , built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and as directed by Engineer-in-Charge.

M&L 15mm thick plastering on concrete surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Racking out joints/pointing to random rubble masonry, polygonal rubble uncoursed or brought upto course complete all as specified and as directed by Engineer-in-Charge.

M&L keyed pointing in CM 1:4 to random or polygonal rubble, uncoursed or brought upto complete all as specified and directed,

Taking down cement plaster on brick or stone walls or concrete surface etc including racking out joints, hacking for key scrubbing down with water all as specified and directed.

M&L rendering 15mm thick on stone masonry surfaces in CM 1:6 finished even and smooth with sagol over and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and as directed by Engineer-in-Charge.

M&L for providing and applying wall care putty not less than 1mm thick over plaster of paris putty not less than 1mm thick on ceiling to prepare the surface even and smooth all as specified and directed by Engineer-in-Charge.

M & L for 15 mm thick cement plaster on concrete surface in CM 1:4 finishing surface even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L preparing newly plastered surfaces of wall and applying POP not less than 1mm thick and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed by Engineer-in-Charge.

M&L for preparation of newly plastered surfaces and applying three coats of white wash on ceiling all as specified and directed.

M&L PCC M-15 grade (Nominal Mix)using 20mm graded crushed stone aggregate in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs , water troughs and the like including weathering, slightly rounded for chamfered angles and throating, as directed

M&L complete removal of existing treatment and applying wall care putty not less than 1mm thick and applying two coat of Oil Bond distemper white or tinned as approved by GE over a coat of primer on walls, etc complete all as specified and directed.

M&L complete removal of existing treatment and applying wall care putty not less than 1mm thick and applying two coat of white wash on ceiling complete all as specified and directed.

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

S&F in repairs 19/20mm dia MS pipe powder coated of approved colour as in decorative type curtain rods for fixing curtain rod all as specified and as directed.

S&F in repairs brackets powder of approved decorative type suitable for fixing curtain rods of 19/20mm dia pipe incl fixing screws, drilling etc as per sample approved by Engr-in-charge all as specified and as directed.

M&L 75mm thick cement concrete M-10 grade ( Nominal Mix) using 40mm graded stone aggregate as in floors, plinth protection, path etc smooth finished surface without using extra cement complete all as specified and as directed by Engineer-in-Charge.

Chipping off loose concrete/plaster upto sound stratum of RCC members such as slab, chajjas, columns, beams and clean the surface with wire brush, washing down with water using water jet including necessary scaffolding & propping to support the structural members where work is to be executed and removing debris to a distance exc 250 meter but n exc 500 meter.

Dismantling boarding, any description, fixed in any position with nails complete all as specified and as directed by Engineer-in-Charge.

Dismantling wall and ceiling boards (fibre, pulp, insulation boards/slabs/blankets, any thickness, including cover fillets

M & L for false ceiling with 4mm thick designer 'E' board fixed on GI grid work with powder coated finish on exposed surface of size 0.6 x 0.6m consisting of GI angle supported on wall of size 24mm x 28 x 0.7mm main tee of size 24mm x38mm x 0.7mm cross tee of size 24mm x 28mm x 0.7 mm using propose made members interlocking to each other and with 40mm x 3mm flat GI mild steel strip suspender made to shape at 600mm c/c fixed with 2mm dia GI wire and making holes etc all as directed including two coats of white wash on ceiling after preparation of surfaces and as per manufacture instruction complete all as specified and as directed by Engineer-in-Charge. Make: Armstrong/Swastik/Techno Grid and Make : E board Gypsum or equivalent approved as given under list of Makes .

M&L for providing and applying rust inhibition coat system (in two coats) as per Manufacturer's instructions to exposed reinforcement after cleaning and removing scales and rust complete all as specified and directed by Engineer-in-charge

M&L for Providing and applying a bond coat (epoxy based bonding materials) to all exposed concrete surfaces all as per the Manufacturer's instructions as specified and directed by Engineer-in-charge.

M&L for providing and applying latex polymer modified cement mortar in specified composition of system [i.e. cement 400 parts by weight, quartz sand 1600 parts by weight, polymer 60 parts by weight, water 120 parts by weight] to RCC surfaces all as per the Manufacturer's instructions and as directed by Engineer-in-charge. NOTE :- Thickness of plaster/filling varies from 15 mm to 25 mm

M&L treatment of soil under existing floors using Chlorpyriphos 20 EC emulsion @ one litre per hole, 300 mm apart including drilling and plugging 12 mm dia holes with cement mortar 1:2 to match the existing floors

Excavating in trenches, n exc 1.5m wide and n exc 1.5 m in depth; for foundation, etc. Or for shafts, wells, cesspits, manholes, pier holes, etc.n exc 10sqm on plan and n exc 1.5m in depth and getting out in hard/ dense soil complete all as specified and as directed by Engineer-in-Charge.

M&L for Cement concrete M-7.5 grade (Nominal Mix) using 40 mm graded stone aggregate) as in foundations, filling and mass concrete etc. complete all as specified and as directed by Engineer-in-Charge.

M&L for Pre-cast cement concrete block masonry of PCC Type C5 design mix with solid blocks straight or curved on plan, exc 6m mean radius and exc. 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed by Engr-in-Charge.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick spread, levelled and rammed including watering complete all as specified and as directed by Engineer-in-Charge.

M & L Hardcore using broken stone boulders not exceeding 63mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and as directed by Engineer-in-Charge.

Supply and fix in repair 1000 litres capacity triple layer, rotational moulded, polythene water storage tank (Cylindrical vertical with closed top) hoisted and fixed on roof in position, including all fitting such as connection pieces with GI tank nipple for inlet, outlet, washout and overflow etc complete all as specified and as directed by Engineer-in-Charge.

M&L 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and as directed by Engineer-in-Charge.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

M&L for framed work for staging of water tank , Bank the like including caps, bases, splices etc built up from two or more beams or channel section or angle with plates ,including all latice bars stiffeners gusset plate etc, or as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings Fe-410-W(Gde E-250) Quality A (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed by Engineer-in-Charge.

M&L for plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment Fe-410-W(Gde E-250) Quality A all as specified and directed.

M&L 15mm thick plastering on concrete surface in CM 1:4 finished even and fair without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M&L 100mm thick cement concrete M-15 grade (Nominal Mix) using 40mm graded stone aggregate and finished even and smooth without using extra cement complete all as specified and as directed by Engineer-in-Charge.

M & L for 18 to 20mm thick Marble work in makrana doongri (table rubbed and polished) in steps, jambs, pillars, windowcills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade complete all as specified and directed by Engr-in-Charge.

S&F Welded steel wire fabric supplied and fixed complete to wood or steel members

S&F in repairs, gun metal globe or gate valves 25mm dia, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engr-in-Charge.

S&F in repairs, gun metal globe or gate valves 20mm dia, with iron wheel head, screwed both ends for iron pipes complete all as specified and directed by Engr-in-Charge.

Taking down carefully copper/aluminium point wiring (light, fan,bell, socket or power) complete, including fixture and fittings such as switches, Ceiling rose, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors, etc . credit for above items should be made as per conditions separately.

Taking down ceiling fan any size or any type and deposited to AGE E/M store all as specified and directed.

Taking down old and unserviceable main incoming MCB DB TPN/ main switch including MCCBs/MCBs and making good the disturbed surface all as specified and directed.

Taking down carefully unserviceable Sub main wiring of any size and type, removing material from for taking credit and making good the disturbed surfaces of walls, ceilings etc

M&L for point wiring for light/fan/Bell with FRLSH cable 1.5 sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 2mm thick PVC casing capping with all accessories and 1.50 sqmm green in colour PVC copper conductor cable for earth continuity connected to common earth dolly incl PVC box surface/ flush type with PVC sheet for mounting fittings such as switches, sockets, fan regulators, etc complete all as specified and directed as following :-

One light point controlled by one one way switch.

One fan point controlled by one way switch and one regulator.

One Exhaust fan point controlled by one way switch.

One 3 pin switch socket outlet 6A on independent board.

One 3 pin socket outlet 6A on same board with other switches

One light point controlled by two 2-way switches

One bell / buzzer point controlled by one push button.

All as per item No. 145.0 above but with cable size 2.5 sqmm for switch socket outlet point 16 A on independent board including 2.5 FRLSH cable sqmm PVC insulated unsheathed copper earth continuity conductor as earth wire and connected to earth dolly complete all as specified and directed.

M&L sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable of size 4 sqmm drawn through and including heavy duty PVC conduit 20 mm or higher dia as required at site, mounted on walls /floors/ceiling with the help of saddles etc including all conduit accessories /fitting/junction box/inspection covers etc of heavy grade, ISI marked with 4 Sqmm PVC insulated unsheathed stranded copper conductor as a continuous earth wire connected to earth dolly complete all as specified. Note : Two single core 4 sqmm cable and one run of 4 sqmm earth copper conductor and 20mm dia heavy duty PVC conduit shall be measured as one unit length.

S & F switch piano, flush type single pole, one way 6 Amp 240 volts AC all as specified and directed

S & F switch piano, flush type single pole, one way 16 Amp 240 volts AC all as specified and directed

S & F bell push, flush type 5 A 240 volts AC all as specified and directed

S & F switch piano, flush type single pole, two way 6 Amp 240 volts AC all as specified and directed

S & F socket out let 2 in 1, 3 pin 6 Amp 240 volts AC flush type all as specified and directed.

S & F socket out let 2 in 1, 3 pin 6 and 16 Amp 240 volts AC flush type all as specified and directed.

S & F Bell, AC 230 V, single pole complete all as specified and directed.

S&F in replacement ceiling rose, 3 terminal PVC/polycarbonate isolated body, surface bakelite 65 x 50 mm, 3 terminal incl PVC square block complete all as specified and directed.

Supply and fixing in replacement ceiling fan complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep min air delivery 210 CFM with service value 6.00 BEE, 5 star rated with bresh less direct current motor (BLDC). all as specified and directed.

Taking down Exhaust fan any type or size and Re-fixing the same after cleaning and connecting up including provision of cable from ceiling rose /connector to fan complete all as specified and directed.

Supply and fixing in replacement LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose complete.

Supply and fixing in replacement LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

S & F sheet metal enclosures VTPN as MCCB incomer and MCB SP out going 4 way 415 V AC dubble door surface/ flush mounting made with CRCA sheet steel, powder coated Cat No 810530 IP 43 protection isolated neutral bar insulated bus bar assembly make INDOASIAN or equivalent complete all as specified and directed..

S & F in replacement sheet metal enclosures MCB SPN- DB-08 way 230 V double door flush type with 100A rated bus bar complete all as specified and directed.

Supply and Fix in MCCB 4 Pole, 415 Volts 50 HZ, of capacity 125 Amp 16 KA. Suitable for VTPN DB as incomer with spreader terminal Cat No 830273 Make INDO ASIAN, Ics= 100% of Icu or equivalent all as specified and directed.

S & F in replacement 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and neutral (SPN) with current carrying capacity of 32 Amp in the MCB DB complete with connection testing and commissioning all as specified and directed. Make: INDOASAIN Cat No 811031/ 811032 or equivalent make given under list of Makes

S & F in replacement 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole (SP) and current carrying capacity 40 Amp in the MCB DB complete with connection testing and commissioning complete all as specified and directed. Make INDOASIAN Cat No 811016

S & F 240 V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole (SP) and current carrying capacity 6 to 32 Amp in the MCB DB complete with connection testing and commissioning complete all as specified and directed. .

Supply & fix LED in replacement fitting for Bldg security, 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65 / 66 protection complete. including connecting with 1.5 sq mm copper conductor 3 core flexible cable from fitting connector to ceiling rose and fix on wall with clamps & nut bolts and necessary GI bracket made of 32 mm light grade GI pipe of 1 mtr length with necessary bending complete all as specified and directed

Material and labour for earthling complete with GI earth plate 600mm x 600mm x 6 mm thick electrode buried directly in ground (earth pit not less then 2.25 metres deep below ground level) with top edge of the plate not less then 1.5 metres below normal ground level connected to GI earth wire 4mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of MES schedule Part-I and including 15 mm bore light grade GI protection pipe (upto 7.5 metres beyond outer edge of earth pit) PCC M-10 grade (Nominal Mix) using 40mm graded stone aggregate in pit with 40mm thick RCC cover in reinforced cement concrete M-15 grade (Nominal Mix) using 20mm graded stone aggregate, reinforced with 8mm dia bar both way @ 150mm c/c, watering arrangement with funnel and wire mesh and 20 mm bore light grade GI watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

Taking down electric water heater (geyser) of any 25/50 litre capacity and refixing the same after cleaning alongwith connected accessories such as PVC connection pipe, fastener etc complete all as specified and directed.

Taking down old single phase electric meter and refixing the same alongwith proper connection complete all as specified and directed. Note : Quarter wise last meter reading shall be noted by the contractor and submitted AGE E/M office

vishalconstruction (BID ID -3340429)

Horizon Construction (BID ID -3341808)

Mehta Construction Co. (BID ID -3341622)

UNIQUE ENGINEERS (BID ID -3341678)

United Sales Corporation (BID ID -3336107)

KHANDELWAL ASSOCIATES (BID ID -3341775)

S.R.M.K Enterprises (BID ID -3341749)

Bidder Name

KHANDELWAL ASSOCIATES

S S ENTERPRISES

Mehta Construction Co.

United Sales Corporation

UNIQUE ENGINEERS

S.R.M.K Enterprises

Horizon Construction

vishalconstruction