Supply, Installation, Testing, Commissioning of 30.5 m High Mast National Flag at MANIT Bhopal

Amount

DSR 2018 Item No. 2.8.1

2.8 Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. 2.8.1 All kinds of soil.

DSR 2018 Item No. 4.1.6

4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 4.1.6 1:3:6 (1 Cement : 3 coarse sand (zone-III): 6 graded stone aggregate 40 mm nominal size)

DSR 2018 Item No. 5.9.1

5.9 Centering and shuttering including strutting, propping etc. and removal of form for : 5.9.1 Foundations, footings, bases of columns, etc. for mass concrete

DSR 2018 Item No. 5.22.6

5.22 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. 5.22.6 Thermo-Mechanically Treated bars of grade Fe-500D or more.

DSR 2018 Item No. 5.37

5.37 Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using cement content as per approved design mix, manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying , excluding the cost of centering, shuttering finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate/ retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer-in-charge. (Note :- Cement content considered in this item is @ 330 kg/ cum.Excess/less cement used as per design mix is payable/recoverable separately). 5.37.1 All works upto plinth level

NON DSR ITEM (MPPWD SOR 6.1.1)

Brick work with well burnt chimney bricks in bulls patent trench kiln manufactured by ghol process, crushing strength not less than 40kg /cm2 and water absorption not more than 15% in foundation and plinth i/c curing etc complete 6.1.1 Cement mortar 1:4 (1 cement : 4 sand)

DSR 2018 Item No. 13.1.1

13.1 12 mm cement plaster of mix : 13.1.1 1:4 (1 cement: 4 fine sand)

DSR 2018 Item No. 2.27

2.27 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

DSR 2018 Item No. 8.2.2.2

8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanityncounters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. 8.2.2 Granite of any colour and shade 8.2.2.2 Area of slab over 0.50 sqm

DSR 2018 Item No.10.28

10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

SCH A NS ITEM - NS/01

Supply, Installation, Testing and Commissioning of 30.5 m flag mast. Mast shaft shall be in three sections, hot dip galvanized and suitable for wind velocity as per IS 875. Mast shall be suitable for Indian Tri Color Flag size 30 ft x 20 ft. It shall have double drum winch, 6 mm dia galvanized wire rope and integral power tool for the raising and lowering of flag. Suitable control panel shall be provided for reversing operation of power tool motor. Supply of aviation system with 3c x 2.5 sqmm Cu armoured cable. Painting of 30.5 m flag mast with a coating of primer and PU painting. Complete in all respects as per enclosed technical specifications and drawing. Rate shall include all labor, materials, tools & plants etc. and with all lead, lift taxes etc. complete. All materials shall confirm to IS standards

Supply of foundation bolts manufactured from special steel along with nuts, washers, anchor plates and templates. (For 30.5 m HM) Rate shall include all labour, materials, tools & plants etc. and with all lead, lift taxes etc. complete. All materials shall confirm to IS standards

Supply of National Flag of size 30 ft x 20 ft in 100% knitted polyester (140 gsm), with reinforced super strong nylon webbing on all 3 sides & robe / toggle sleeve, as per enclosed technical specification. Rate shall include all labor, materials, tools & plants etc. and with all lead lift, taxes etc.

Supply, Installation, Testing and Commissioning twin dome LED Aviation obstruction lighting with two LED fittings complete in all respects as per enclosed technical specifications and confirming to ICAO. Rate shall include all labor, materials, tools & plants etc. and with all lead, lift taxes etc. complete.

Supply, Installation, Testing and Commissioning of 3 m high hot dip galvanized octagonal PU painted pole of minimum 3 mm wall thickness of S 55 grade compliant with BSEN 10025 suitable to mount 1 No. LED 350 W flood light fittings at top with suitable mounting arrangement. Fixing of luminaries with all wiring materials like PVC insulated, PVC sheathed, flexible cable of suitable copper conductor cores of 1.5 sum, lugs, MCB and all labor including testing of system. Poles shall have a base plate with minimum 20 mm thickness and four foundation bolts. Rate shall include all labor, materials, tools & plants etc, and with all lead lift, taxes etc. complete all materials shall confirm to IS standards

Supply, Installation, Testing and Commissioning of LED flood light luminaries 350 W specially designed for flag mast lighting purpose to focus proper light from ground to 30 m height. Fitting should be extruded aluminum housing cum heat sunk made of pressure die cast aluminium body with and covers and high power discrete LEDs with secondary lenses for optimum optical performance. Driver with in-built protection against surge voltage (up to 4.5 kV) open/short circuit along with suitable arrangement and support for mounting luminary for focus lighting on flag. Rate shall include all labour, materials, tols & plants etc, and with all lead lift, taxes etc. complete all materials shall confirm to IS standards

Erection of the Flag Mast with the help of suitable equipments and assembly of operating system and flag. Wiring of luminaries with all wiring materials light PVC insulated, PVC sheathed flexible cable of suitable copper conductor core of 1.5 sqmm, lugs, MCBs and all labour. Rate shall include all labour, materials, tols & plants etc, and with all lead lift, taxes etc. complete all materials shall confirm to IS standards

Provision of GI pipe earthling for High Mast with 2.5 m long 40 mm dia GI pipe including connection to High Mast earth terminal with 25 x 3 mm GI flats. Rate shall include all labour materials, tools & plants etc and with all lead lift, taxes etc. complete all materials shall confirm to IS standards

Supply of driver suitable for 350 Watt LED light fitting installed against S.No. 6 above. Rate shall include all labour, materials, tools & plants etc. and with all lead, lift taxes etc. complete.

Manish Electricals