SPECIAL REPAIR TO BLDG NO P-211 AND GUEST ROOM AT HQ 91 SUB AREA CAMP AND GTO MUSTER ROOM NEAR GTO GROUND AT SCN UNDER GE (WEST) JALANDHAR CANTT

Amount

Demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and directed

M&L for rendering 15mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished even smooth without using extra cement complete all as specified and as directed.

Taking down cement plaster including raking out joints, hacking for key,scrubbing down with water built in cement mortar all as specified and as directed.

M&L brick work with sub-class 'B' old size bricks, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 complete.

M&L brick work with sub-class 'B' old size bricks, straight or curved on plan to any radius built in cement mortar 1:4 complete.

M&L for cement concrete type D2, 1:4:8 using 40 mm graded stone aggregate as in foundation, filling and mass concrete complete.

M&L 75mm thick PCC 1:3:6 type C2 (using 40mm graded stone aggr) as in plinth protection/path finishing the surface even and smooth without using extra cement complete all as spd and directed. Note : Plinth protection shall be laid in (1:20) slope. The concrete shall be laid at a stretch not exceeding 3metre in length. Joint gap between adjoining slab, at corners and at junctions of walls shall not exceed 10mm in width and shall be sealed with mastic filling i.e. one part of bitumen 85/ 25 grade mixed with 3 part of sand. Top surface of concrete shall be finished even and smooth without using extra cement. Joints shall be provided at not more than 3 metre interval at corner and junction of walls.

M&L 15mm thick rendering using water proofing compound on wall in cement mortar 1:4 on brick/concrete surface and finishing the surface even and fair without using extra cement. (Water proofing compound shall be measured and paid separately in respective item)

M&L 15mm thick rendering on wall in cement mortar 1:6 on brick/concrete surface and finishing the surface even and smooth with out using extra cement.

Demolition of floor hearth or wall tiling including cement mortar bedding (not backing ) removing serviceable tiles to store and rubbish off the premises

M&L coloured Glazed ceramic tiles in vertical surface 350x 250x 7 mm/ 450X 350X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match the surface over & including 10 mm thick rendering in cement mortar 1:4.

M&L Non skid Coloured ceramic tiles 7 to 8 mm thick (square or rectangle) area of each tile exc 0.11 Sqm but not exceeding 0.18 Sqm in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match with & including 15mm thick screed bed in cement mortar 1:6.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any morter.

M&L Machine cut kota stone slab flooring 20-25mm thick over 20mm thick cement screed bed in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete.

M&L Machine cut kota stone slab flooring 20-25mm thick as in skiritng, riser of steps etc laid over 10mm thick cement plaster in CM 1:4 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing upto mirror finished complete.

M&L for Marble work 18 to 20mm thick (table rubbed and polished) as border line in floor using makrana white, fixed in cement mortar (1:4) over & including 20mm thick screed bed, including pointing in white cement (1:2) using marble dust with admixture of pigment to match.

Mirror polishing on old stone surfaces by machine on old marble/granite/Kota stone/stone work where ever required to give high gloss finish complete.

M&L Chequered cement concrete tiles 25cmx25cmx25mm thick as in path etc. set and jointed with grey cement and pigments as in floors over and including screed bed or bedding layer of mortar 15mm thick laying floor finishes in cement mortar 1:6 complete all as specified and directed

Rounding/moulding to edges of Kota stone slabs, marble stone, granite stone slabs one edge, such as in steps, cooking platform , and other similar situations etc

Taking down chowkats or frames with shutters (without taking off shutter from the frame) of any description alongwith fittings n.exc 1.5Sqm each

Taking down chowkats or frames with shutters (with out taking off shutter from the frame) of any description alongwith fittings exc 1.5Sqm n.exc 4 Sqm each

Taking down shutters of any description exc 1 Sqm and not exc 2 Sqm each and refixing in same opening after necessary repairing. Note : Change of old wiremesh will be measured in connected supply only items.

S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 105 x60mm complete.

S&F pressed steel door frame with one or more rebate including necessary fixing lugs, hinges, lock stricking plate of size 125 x60mm complete.

M&L for PCC Type B0-1:2:4 using 12.5mm graded aggregate as in filling of pressed steel frame, hold fasts and similars articles

S&F for 2nd class hard wood in Small fittings such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including all necessary' labours; articles n exc 200 cu. cm each

S&F for MS work in bands, straps, supports of stays, sunshade brackets, hook and pintle hinges, clamps, hold fasts, grills bolts etc and similar conforming to Fe-290 Gde-E-165.

Cutting holes in brick walls built in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required built in cement motar in brick wall depth of embedded portion of holdfast exc half brick but n exc one brick

S&F 2nd class hardwood, factoy made plain,framed,panelled shutters (two panel) 35mm thick, with lock rails and panel of 9mm B. W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rails and stile as per IS : 1003 (Part-I), kiln seasoned and chamically pressure treated.

S&F 2nd class hardwood glazed and skelton door shutters 35 mm thick divided into squares open rebated and prepared to receive glass, gauge etc edges of framing plain, chamfered, rounded fitted with mitred beads for securing glass etc, size of members as specified in SSR section 8 clause 8.20 (b) supplied and fitted to chowkats.

S&F 35mm thick flush door shutter, solid core construction with block board core, and plywood face panels, commercial type on both side complete all as sped and directed.

M&L Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube

S&F factory made solid panel PVC door shutter 30mm thick (style) consisiting of frame made out of M.S. Tubes for top & bottom rails M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, fixing in the frame at the site as per specification & drawing.

M&L Box type Steel window/ventilator made out of 1.25 mm thick ERW hollow P section of size 60mm x 25 mm single rebated comprises skelton shutter ERW Sec 50 MM x 20 mm and 1 mm thick and two openable leaf consisting two Nos sash bar of T-section 20 mm x 3mm complete welded to frame with one vertical mullion of ERW box type T section of size 60mm x 25 mm and 1.25 mm thick, including shop coat primer and following fittings welded to shutters:-i) Hold fasts 150 mm long, made out of flat iron 12mm x 3mm made to shape -04 No’s, (ii) Handle of Z sec 20mm x 25mm , 100mm long per leaf -1 No’s (iii) MS tower bolt 150 mm long per leaf -2 No’s (iv) Z sec 20mm x 25 mm , 100 mm long stopper per leaf -1 No (v) Cleat 55 mm long of hollow square 15mm x 20mm x 63 mm welded to hinges per leaf -01 No (vi) MS pintal hinges of size 75mm x 12 mm per leaf -02 Nos (vii) Fabrication and fixing arrangement complete

All as per Ser item No 34.00 above but glazed window shutter.

S&F framed work such as grills, gratings with ends of bars shouldered or forged in spickes, framed guard bars, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-290 Gde-E-165

S&F Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and average width of aperature 1.18 mm fixed with tinned tacks, or galvanised wire staples.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square n.exc 0.50 Sqm in each pane complete all as specified.

Supply only Galvanised mild steel wire cloth, 0.56mm nominal dia of wire and width of aparture 1.18mm fixed with alu wire staples fixed to wood/steel frames.

S&F Butt hinges, medium weight cold rolled 100 mm size.

S&F Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin,anodised and fixed type B-21 of 100 mm size.

S&F aluminium anodised barrel tower bolts of extruded section 150mm long all as specified/

S&F Extruded aluminium alloy handles fabricated type anodised 150mm size

S&F aluminium alloy anodised sliding door bolts 250 mm long with hasp, staple (bolt type)and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded sections as specified.

S&F 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete.

Dismantling wrought iron or mild steel work of any description not otherwise provided for.

M&L for providing and fixing stainless steel (Grade 304) railing made of hollow tubes, channels, plates etc. including welding grinding, buffing, polishing and making curvature (where ever required) and fixing the same with necessary stainless steel nuts and bolts complete including fixing the railing with necessary accessories and stainless steel dash fasteners,stainless steel bolts etc,of required size, on the top of floor or the side of waist slab with suitable arrangement.

M&L for 15mm thick rendering in cement mortar 1:3 with using @ 3% WPC as in sunken portion complete all as directed.

Supply only integral water proofing compound.

M&L Cement concrete type E-2, 1:5:10 using 40mm graded stone aggregate in foundations filling and mass concrete as in sunken floor.

M&L 25mm thick cement concrete flooring type B-1, 1:2:4, using 20 mm graded stone aggregate finishing cement concrete surface even and smooth without using extra cement.

Taking up or down 15 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed.

Taking up or down 20 mm bore steel tubing and connection including cleaning for re-fixing or removal to store complete all as specifed and directed.

S&F 15mm bore GI tubing medium grade fixing complete to wall and ceiling or laid in floor complete all as specifed and directed.

S&F 20 mm bore GI tubing medium grade fixing complete to wall and ceiling or laid in floor complete all as specifed and directed.

Cutting chases, pinning in making good to facings where reqd and pointing in cement mortar 1:3 to ends or edges of shelves , for water tubing etc and making good, cutting exc 10cm girth but not exc 20cm girth in stone walls

Supply, hoist and fixing in position,500 litres capacity rotational moulded polythene water storage tank (cylindrical, vertical with closed top) ISI marked (Name of firm embossed or engraved on the body of tank) conforming to IS 12701, double layered including S&F 20mm dia, 450mm long GI washout pipe (medium grade) with plug and 20mm dia, 600mm long overflow GI pipe (medium grade) with all fittings including dismantling the existing tank complete all as specified and as directed.

All as per Ser item No 57.00 above but except water storage tank of 500 ltr capacity with locking arrangement and fixed in position all as specified and directed

S&F 20mm Gun metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed in repair

S&F ball float valve PTMT with epoxy coated aluminimum rod for 20 mm bore pipe high pressure with polythelene high density float and complete screwed for iron pipe.

S&F in repair 15mm dia Bib taps cast copper alloy with fancy type chromium plated with crutch or butterfly handle screwed down, scewed for iron pipes or for brass ferrule

S&F 15mm bore stop valves brass chromium plated, fancy type with long shank and cup concealed type screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union complete all as specified and fixed in repairs.

S&F in repair pillar taps, cast copper alloy with capstan heads chrominm plated fancy type, screwed down high pressure with or without lettered Hot or Cold with long screwed shank and fly nuts, srewed for iron pipe and fixed 15mm bore.

S&F in repair vitreous china wash hand basin, white, flat back size 550mmx400mm including cast iron or mild steel brackets including cutting for and pinning in brackets complete all as specified and as directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specifed and directed.

S&F in repairs 10 Litre PVC valveless syphonic action flushing cistern low level white with inlet ball valve, float and handle including brackets and flush pipe of polyethylene 32 mm dia for low level cistern

S&F Health faucet (ABS body) mild steel chromium plated suitable for 15mm dia pipe with 1.25mtr long flexible tube and ABS wall hook including making connection and fixed in position complete in all respect as specified.

S&F 15mm PVC connection 450mm long with PTMT nuts of superior quality as specified

S&F brass chromium plated soap dish, any type fixed to walls with plugs with chromium plated brass screws

S&F for brass chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges etc complete all as spd and directed.

S&F brass chromium plated shower rose 125mm size complete all as spd and directed.

Taking down existing water proofing treatment from roof slab and cleaning the roof slab incl scrapping of existing loose concrete from roof top and washing with water complete all as specified and directed.

M&L 10mm thick rendering on top of roof slab in cement mortar 1:4 by using water proofing compound @3% by the weight of cement, finishing the surface even and fair without using extra cement.

M&L for priming surfaces with bituminous primer polymerised primer oil based @ 0.40kg per Sqm.

M&L for applying evenly a tack coat of industrial bituminous 85/25 @ 1.20 Kg per sq mtr including cleaning surfaces.

M&L APP based polymeric membrance minimum weight not less than 3.0kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/Sqm) land on primed surface by forced application( sealed by flame) with over lap of 10 cm finally it will be finished with a coat of aluminium paint @0.200 Kg/Sqm as per manufactures instruction complete all as specified and directed.

Dismantling of brick tiles single layer as in roof covering complete all as specified

Demolition of mud in roofs any thickness including plastering and leeping(whether full thickness removed or only a part thereof) all as specified.

Cleaning/Roughening surfaces of old concerete floor/roof by picking , sweeping clean and washing down with water to romove the dust etc complete all as spd.

M&L APP based polymeric membrance minimum weight not less than 3.0kg/Sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt not less than 150gms/Sqm) land on primed surface by forced application( sealed by flame) with over lap of 10 cm complete all as specified and directed.

M&L 40mm thick Brick tiles laid on 15mm thick bedding layer of cement mortar 1:6 and joints grouted flush in cement mortar 1:3 mixed with 5% of crude oil by weight of cement over APP membrane complete all as spd and directed.

All as per Ser item No 82.00 above but except tiles

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories)

Dismantling of cast iron or reinforced concrete drain pipes of size 100mm dia, jointed in cement mortar and taking out of trenches, if required.

M&L 75mm PVC (SWR) floor trap , plain with grating including jointing with solvent cement complete all as spd and directed

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints,fixed to walls complete

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints, fixed to walls

S&F 110mm PVC (SWR) bends

S&F 75 mm PVC (SWR) bends

S&F 110mm PVC (SWR) junction single, (Single T) equal or unequal

S&F 75 mm PVC (SWR) reducers

S&F for PVC 110mm (SWR) vent cowl

M&L for repairing of R.C.C projections, chajjias, roofs, facia etc in patches not exceeding 3 Sqm in each patch by necessary preparation. Scarpping, cutting, chiseling derusting and cleaning exposed reinforcement, surfaces of damaged, loose R.,C.C surfaces and applying one coat of cement slurry/standerd rust stop solution on exposed surfaces of steel and filling the surfaces with cement concrete (1:1.5:3) using 12.5mm graded crushed stone aggrigates and reinforced with welded mesh (If Reqd) of weight exc 2 kg per Sqm but n.exc 3kg/Sqm with or without facia and finished with cement and sand motar (1:3) using coarse sand and work in patches and thickness of R.C.C member n.exc 75mm including necessary form work and applying two coats of finishes to match with the existing surfaces at any height complete all as specified and directed by Engr-in-charge. (Note : Cost of form work and welded mesh,rust stop solution shall be deemed to be included in unit rate quoted by the contractor against this item complete all as specified and as directed.

M&L for applying two coat of synthetic enamelled paint over one coat of pink primer including preparation of new wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M&L for applying one coat of synthetic enamelled paint including preparation of old treated wood surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M&L for applying two coat of synthetic enamelled paint including preparation of new steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M&L for applying one coat of synthetic enamelled paint including preparation of old decorated steel surfaces of any description not otherwise described over 10 CM girth or width all as directed by the Engr in charge

M&L for applying white wash of 3 coats as in ceiling incl preparation newly plastered surfaces as specified and directed.

M&L for preparation of new plastered surfaces on walls and applying two coats of oil bound distemper over one coat of chalk whitening complete all as specified.

Complete removal of existing treatment on wall and applying Two coat of oil bound distemper (white or tinted) over one coat of thin layer of putty (not less than 1mm) on plastred surfaces, preparatory to distempering on walls etc (Surface finished even and smooth) complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces on walls and applying two coats of cement base paint over one coat of cement primer complete all as specified.

Complete removal of existing treatment on wall and applying two coats of cement base paint complete all as specified.

M&L for vitrified ceramic tiles 10mm thick, light shade, polished, area of each tiles n. exc 0.36 Sqm (square / rectangular) in floor etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles with & including screed bed 15mm thick in cement mortar (1:6) finished rough to fix tiles complete all as specified and directed.

M&L for vitrified ceramic tiles 10mm thick, light shade, polished area of each tiles n. exc 0.36 Sqm (square / rectangular) as in vertical surfaces i.e. skirting/dado set and jointed in neat cement slurry and pointed in white or coloured cement to match the existing surface with & including rendering 10mm thick in cement mortar (1:4) finished rough to fix tiles complete all as specified and directed.

Dismantling wall and ceiling board, fibre, pulp insulation etc or insulation boards any thickness including cover fillets complete all as specified and as direced by the Engr-in-Charge

S&F 4mm thick size 600x600mm HPSC (High pressure steam cured) pre-primered self embossed, textured designerd board E- board classic to be fixed on including GI powder coated grid /section size 600x600mm with main runner 38x24x0.9mm thick, cross tee 28.6x24x0.9mm and wall angle 19x19x0.9mm duly suspended with 6mm dia GI bar hangers 1200mm c/c both ways fixed with steel dash fasteners or from purlin from the roof with alignment clip including provision for light fixtures of any size and including taking down old ceiling complete all as specified and as directed.

S&F aluminium anodised frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and as directed.

Anodised aluminium door shutters, aluminium section weighing not less than 1 kg / m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified.

Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing not less than 1 kg / m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified

M&L for 5.5mm thick sheet glass ordinary quality including solar control film 25 micron reflective type sticked on glass pane as per instructions of manufacturer and glazing fixed with oil putty in squares not exceeding 0.50 Sqm in each pane complete all as specified and directed.

S&F 18-19 mm thick pre-laminated particle board, exterior grade, pre-laminated one side with decorative choice lamination and other side balancing white lamination, fixed with screws to timber framework complete all as specified.

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor overall length of cover plate 150mm long complete all as specified and as directed.

M&L for 5mm thick rendering in cement mortar 1:3 on brick or concrete surfaces of ceiling finished even and smooth without using extra cement complete all specified and as directed.

Supply, hoist and fixing in position,1000 litres capacity rotational moulded polythene water storage tank (cylindrical, vertical with closed top) ISI marked (Name of firm embossed or engraved on the body of tank) conforming to IS 12701, double layered including S&F 20mm dia, 450mm long GI washout pipe (medium grade) with plug and 20mm dia, 600mm long overflow GI pipe (medium grade) with all fittings including dismantling the existing tank complete all as specified and as directed.

S&F cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) using 20mm graded stone aggregate) diameter of outlet 75mm complete all as specified and as directed.

S&F in repairs vitreous china wash down water closet pan (pedestal pattern), white, and connection to drain (or outgoing pipe) and connection to flushing pipe, anti-syphonage pipe, (excluding flusing cistern and flush pipe) etc complete all as specified and as directed.

M&L for PCC pedding with cement concrete type B-1, 1:2:4 (using 20mm graded stone aggregate) to top surface of slab/sunken floor in slop 1:40 complete all as specified.

Plain Cement Concrete Type B1 1:2:4 (using 20 mm graded stone aggregate) cast in situ in kerbs or mud stops, rounded or chamfered on edges of paving blocks as directed including use and waste of form work.

Excavation in trenches not exc. 1.5 m wide and n. exc. 1.5m in depth for foundation, etc, or for shafts, wells, cesspits, manholes, pier holes, sewage line etc. and getting out in soft/loose soil complete all as specified and as directed.

Excavation in trenches exc. 1.5 m wide and n. exc. 3.0 m in depth for foundation, etc, or for shafts, wells, cesspits, manholes, pier holes, sewage line etc. and getting out in soft/loose soil complete all as specified and as directed.

Removing excavated material to a distance exc 50 metre but n exc 100 metre and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and as directed.

Returning filling in, including, spreading, leveling and well ramming in layers not exceeding 25cm complete all as specified and directed.

Demolition and breaking up drain pipes (SGSW, AC or reinforced concrete pipe) 200mm internal dia set in cement mortar complete all as specified.

M&L for 200mm bore salt glazed stone ware drain pipes (Grade-A) laid in trenches and jointed in CM 1:1 and tested complete all as specified and directed.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in concrete bed to 200mm bore drain pipes including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

M&L for cutting into existing manholes for connecting new drains, making good to open and rendering, cutting out existing benching for forming branch, channel (1/2 round or 3/4 section) in cement concrete (1:2:4) type B-1 and making good pipe and reforming benching as required finishing even and smooth dia of pie 200mm complete all as specified and directed.

M&L for providing PCC (1:2:4) type B-1 (using 20mm graded stone aggregate) as in coping, channel,benching/ haunching of manhole, drain, laid to shape and slope, slightly rounded or chamfred angle and throating including necessary form work etc complete all as specified and directed.

Taking down carefully aluminium / copper point wiring (light / fan / socket or power) complete including fitting such as switches, ceiling roses, socket, light fittings, regulators etc complete and making good disturbed surfaces of walls, floors

Taking down main switch / DB as directed by Engineer-In-Charge.

M&L for concealed point wiring complete with 1.5 Sqmm single core multistranded copper conductor FRLS, PVC insulated and unsheathed cable 1100 volts grade drawn through & including PVC conduit ,medium grade with accessories like bends, tees, junction boxes etc fix on wall or ceiling surfaces all as specified including 1.5 Sqmm , FRLS type , copper multistranded cable as earth wire including pressed steel sunken boxes for mounting of MODULAR TYPE switch/sockets and regulator and including modular type cover plate white colour all as specified and directed for: One light / fan point controlled by one, one way switch.

One light point controlled by two 2 way switches with cable 1.5 Sqmm size

One 3 pin socket out let 5 Amps on same board with other switches.

One 3 pin socket out let 5 Amps on Independent board with other switches.

All as per item No 131.00 above but with 2.5 Sqmm multistranded copper conductor FRLS cable with 2.5 Sqmm earth wire for one 6 pin socket outlet 15 amps on independent board

All as per item No 131.00 above but with 4.00 Sqmm multistranded copper conductor FRLS cable with 4.00 Sqmm earth wire for one 6 pin socket outlet 15 amps on independent board

S&F switch MODULAR 6 Amps, SP, one way, 230 Volts, AC complete

S&F switch MODULAR 16 Amps, SP, one way, 230 Volts, AC complete

S&F socket outlet multipurpose MODULAR 5 pin 6 Amps, flush type, 230 Volts

S&F socket outlet multipurpose MODULAR 5 pin 6/16 Amps, flush type, 230 Volts

S&F MODULAR fan regulator step type 120W, 02 module complete all as specified and directed.

M&L ceiling rose surface bakelite 65 x 50 mm three terminals PVC/ polycarbonate isolated body complete all as specified.

Supply, installation & commissioning MCB Load Distribution board TPN 4 way double door, for mounting DP/ SP/TP/ MCBs/MCCBs as Incoming / outgoing, factory made, confirming to IS, fabricated out of CRCA sheet , fitted with DIN channel, neutral link and suitable rated bus bar, DBs shall be semi glossy finished with epoxy polyester based powder coated baked at high temperature, between powder paint process the sheet steel having to go through the anti rust conditioning in not less than seven tank process to ensure smooth finish and protection against corrosion atmosphere. The DBs shall be double door type with hinged door with locking arrangement. The DP/SP/TP MCB shall be of same make as DB. DB shall also be provided with label marking indicating the incoming and outgoing circuits on all way as specified. The DBs shall be of IP 43 - IK 09 with metal door complete all as specified and directed at site .

S&F MCB TPN 63 Amps, 4 pole , 16 kA 415 volts complete all as specified and directed.

S&F MCB SP 6-32 Amps 240 volts complete

Supply and Fixed single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of cap 20A complete all as specified and directed.

S&F LED tube light fitting 20W (Double side) including LED lamp 20W with 2100 lumen output with internal surge protection device of 4KV with voltage band of 140-280V CRI-6500K (White light) fixtures box type and connecting electrically to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.50mm 3 core complete all as specified and directed.

S&F LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete.

Supply and Fix recess/ceiling mounting LED light 1x36 Watt cool white light of 6500k complete all as specified and directed. Make Havells Model No - DROPDWONFLAT2x2PLR36WLED857S or equivalent in CG/Bajaj

Supply & fixing in replacement LED street light fitting 30 Watt including LED lamp pressure die cast aluminum IP66 with surge protection device of 10KV, IK7 LED (SEOUL) 6500K and connecting to ceiling rose using PVC insulated and overall sheathed flexible copper conductor of size 0.50 mm 3 core including GI pipe bracket made out of 32mm dia light grade 0.9 Mtr long bent to L shape with 02 Nos of GI Clamps made out of flat iron 25x6 mm with nuts, bolts and washers complete complete all as specified and directed.

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings

Supply and laying XLPE insulated , armoured electric cable heavy duty with aluminium conductor , 1100 volts to be laid in trenches of size 4 Core 16 Sqmm

Supply and laying GI Tube Med grade 50mm dia incl all fitting all as specified and directed.

M&L river sand in trenches as cable cushioning 8 cm below the cables and 15cm above the cable which is to be punned down to 10cm all as specified and directed.

Removing the surplus excavated materisl/soil to a distance not exc 50Mtrs and depositing, where directed at a level not exceeding 1.5 Mtr above the starting point all as specified and directed.

Supply and lay burnt bricks sub class 'B' standard size laid across the cable in trenches as protection to the cable all as specified and directed.

M&L for earthing complete with GI steel earth plate electrode 60x60cmx6.00mm thick buried directly in ground / earth pit not less than 2.25m deep below the ground level with top edge of the plate not less than 1.5 m below the normal ground level connected to test point by using GI wire of dia 4mm as earthing lead soldering/ revited to earth plate at one end and connect to DB by means of nut, bolts etc complete with PCC pit (1:3:6) type C1, MS cover with handle funnel with watering pipe wire mess GI protection pipe for earthing lead all complete as specified and as per electric plate No.3 of SSR Part I

S&F ceiling fans complete with blades, down rod , electronic regulator switch type 5 step and accessories 230V, 1200 mm sweep, Min air delivery 210 CFM with service value 6.00 BEE, Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

Supply and fix Exhaust fans Plastic body AC single phase 230/ 240 V of size 250 mm sweep with louver, as required for fixing and electrical connection upto ceiling rose including making opening in walls and making good to match with existing complete all as specified and directed.

Taking down unserviceable Submain/Cable of any size as directed by Engineer-In-Charge.

S&F switch piano 6 Amp flush button type SP one way, 230 Volts, AC complete

S&F switch piano 6 Amp flush button type SP two way, 230 Volts, AC complete

S&F socket out let multipurpose 5 pin 6 Amps, flush type, 230 Volts complete

S&F Switch piano 16 Amp, flush button type SP one way, 230 Volts AC complete

S&F socket combination 6 pin 16 Amp flush type multipurpose 230 Volts AC complete

S&F stepped socket type electronic fan regulator and connecting up complete 230/250 V as directed by Engr - in-Charge.

S&F Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings incl 01x 09 Watt LED bulb complete all as specified and directed.

S&F for sub main wiring with two single core PVC insulated and unsheathed cable 6 Sqmm with multi stranded copper conductor , FRLS type cable drawn through and including PVC concealed conduit of not less than 25mm in size complete with all accessories alongwith provn of 6 Sqmm PVC insulated and unsheathed ,multi stranded copper conductor , FRLS type cable as earth wire.(Three runs of cable and one run of conduit shall be measured as one length)

Supply & fix Exhaust fans steel body AC single phase 230/ 240 V of size 300 mm sweep with louver, as required for fixing and electrical connection upto ceiling rose including making opening in walls and making good to match with existing complete all as specified and directed.

S&F DB double door SPN 8 Way for MCB 240V with 200 Amp rated bus bar

S&F MCB SPN 32 to 63 Amps 240 volts 10 KA

Supply and lay cable XLPE Insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25 sq mm 4 core

M/S RAJESH CONSTRUCTION COMPANY

NATIONAL BUILDERS

PAUL CONSTRUCTION CO.

M/S Vinod Kumar

nitin trading company