Loading…
Tenderkart now works inside Claude and ChatGPT: search and analyse tenders right from your chat
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹29.3 LAccepted-AOC | L1 | Accepted-AOC LOWEST | |
| 2 | L2₹30.0 L+₹50,511 (1.71%)Rejected-Finance | L2 | Rejected-Finance HIGHER | |
| 3 | L3₹30.1 L+₹62,104 (2.11%)Rejected-Finance | L3 | Rejected-Finance HIGHER | |
| 4 | L4₹30.6 L+₹1.2 L (3.91%)Rejected-Finance | L4 | Rejected-Finance HIGHER | |
| 5 | L5₹31.4 L+₹1.9 L (6.48%)Rejected-Finance | L5 | Rejected-Finance HIGHER |
Tender Value
₹37.5 L
EMD Value
₹75,000
Closing Date
5 Sept 2022, 6:00 pmClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
GE Amritsar
GE Amritsar PIN-143001
PROVN OF ADDITION/ALTERATIONS TO COOK HOUSE (BLDG NO DD3A AND DD4A) AT OLD AMRITSAR CANTT
2022_MES_544221_1
GE/ASR-39/2022-23
Open Tender
Civil Works
Item Rate
180 days
GE Amritsar
Class D, category ai
8 documents required · 8 mandatory
₹500
GE Amritsar
₹75,000
Yes
12 Dec 2022
8 Aug 2022
6 Sept 2022
8 Aug 2022
5 Sept 2022
23 Aug 2022
Amount
Taking down shutter any description of size exceeding 1Sqm and not exceeding 2Sqm and removing from site ; complete all as specified and directed by the Engineer in Charge.
Taking down chowkhats or frame without taking of shutter from the frame of any description size exceeding 1.5Sqm and not exceeding 4Sqm and removing from site ; complete all as specified and directed by the Engineer in Charge.
Taking down chowkhats or frame without taking of shutter from the frame of any description size not exceeding 1.5Sqm and removing from site ; complete all as specified and directed by the Engineer in Charge.
Taking down shutters of any description exceeding 1Sqm & not exceeding 1.5Sqm each and refixing in the same opening ; complete all as specified and directed by the Engineer in Charge.
Taking down cement plaster from wall's/ceiling including raking out joints hacking for key scrubbing down with water and dispose off debries out of MoD land ; complete all as specified and directed by the Engineer in Charge.
Demolition of cement concrete (un-reinforced)in ground floor and paving not exceeding 15cm thick below or above ground level & dispose off debris upto a distance not exceeding 50 metres where directed ; complete all as specified and directed by the Engineer in Charge.
Demolation of RCC in any position not otherwise specifically provided & dispose off debris upto a distance not exceeding 50 metres where directed ; complete all as specified and directed by the Engineer in Charge.
Material and labour PCC 1:2:4 type B-0 using 12.5mm graded crushed stone aggregate as in hold fast block, roof kerbs or mud stop, coping, rounded or chamfered on edges and like including weathering, slightly rounded or chamfered angles and throating etc incuding necessary form work ; complete all as specified and directed by the Engineer in Charge.
Demolition of brick work built in cement mortar, seperation, cleaning and stacking of serviceable bricks for reuse and removal of debris,rubbish to a distance exceeding 400metres but not exceeding 500metres ; complete all as specified and directed by the Engineer in Charge.
Material and Labour for brick work with sub Class 'B' old size bricks, straight or curved on plan exceeding 6 Metre mean radius, built in cement mortar 1:6 ; complete all as specified and directed by the Engineer in Charge.
Material and Labour for brick work but except bricks (using serviceable bricks obtained from demolition), straight or curved on plan exceeding 6 Metre mean radius, built in cement mortar 1:6 ; complete all as specified and directed by the Engineer in Charge.
Material and labour for 15mm thick cement plaster in cement mortar (1:6) on fair faces of brick or concrete surfaces and finishing the surfaces even and smooth without using extra cement ; complete all as specified and directed by the Engineer in Charge.
Material and labour for 10 mm thick cement plaster in cement mortar (1:3) on concrete surfaces of ceiling and finishing the surfaces even and smooth without using extra cement ; complete all as specified and directed by the Engineer in Charge.
Material and labour for 15mm thick cement plaster in cement mortar (1:4) on fair faces of brick work and finishing the surfaces even and smooth without using extra cement ; complete all as specified and directed by the Engineer in Charge.
Material and Labour for preparation of new plastered surfaces of walls and applying two coats of oil bound distemper over one coat of cement primer on walls , including cleaning of windows, doors, internal fittings & any other surfaces by removing splashes / spots after finishing the job and leaving premises, clean and tidy ; complete all as specified and directed by the Engineer-in-Charge.
Material and Labour for preparation of old decorated plastered surfaces of walls ,complete removal of existing treatment on walls, ceiling , applying average 1mm thick wall puty and applying two coats of oil bound distemper on walls , including cleaning of windows, doors, internal fittings & any other surfaces by removing splashes / spots after finishing the job and leaving premises, clean and tidy ; complete all as specified and directed by the Engineer-in-Charge.
Material and Labour for preparation of new plastered surfaces of ceiling and applying three coats of Lime white wash on ceiling , including cleaning of windows, doors, internal fittings & any other surfaces by removing splashes / spots after finishing the job and leaving premises, clean and tidy ; complete all as specified and directed by the Engineer-in-Charge.
Material and Labour for preparation of old decorated plastered surfaces of ceiling , filling nail holes or patches with wall care putty to make surface smooth and applying one coat of lime white wash , including cleaning of windows, doors, internal fittings & any other surfaces by removing splashes / spots after finishing the job and leaving premises, clean and tidy ; complete all as specified and directed by the Engineer-in-Charge.
Material and Labour for preparation of new plastered surfaces of walls and applying two coats of cement base paint over one coat of cement primer on walls , including cleaning of windows, doors, internal fittings & any other surfaces by removing splashes / spots after finishing the job and leaving premises, clean and tidy ; complete all as specified and directed by the Engineer-in-Charge.
Material and Labour for complete removal of existing treatment from old plastered/unplastered surfaces of walls and applying two coats of weather proof external paint over one coat of cement primer on walls , including cleaning of windows, doors, internal fittings & any other surfaces by removing splashes / spots after finishing the job and leaving premises, clean and tidy ; complete all as specified and directed by the Engineer-in-Charge.
Material and Labour for Box type steel window double shutters (both Glazed & Gauzed shutters) made of ERW tube P - section of size 60 mm x 25 mm double rebated outer frame, comprises glazed skelton & gauzed shutter of ERW tube P-Section size 50mm x 20mm with one/two Nos openable leaf for each shutter consisting of two Nos Sashbar of T-section 20 x 3 mm welded to frame with one No verticle mullion of ERW box type T Section of size 60mm x 25mm and FI 2mm thick welded/screwed to frame for fixing of glass with & including Sheet glass, SS wire cloth, fittings and fixture like as Handle, Tower Bolt, Stopper, Cleat, Pintal hinges, holdfast etc as given below all as shown on drg No CEJZ/TD-1019/08 Sh 1/3 to 3/3 dt 01 May 2008 ; complete all as specified and as directed by the Engineer-in-Charge :- (a) Hold fasts 150mm long of 12mm x 3mm MS flat - 4 Nos per Window. (b) Handle of Z section 20mm x 25mm, 100mm long- 01 No per leaf. (c) MS tower bolt 150mm long - 02 Nos per leaf.(d) Z Section stopper 20mm x 25mm, 100mm long - 1 No per leaf. (e) Cleat 55mm long of hollow square 15mmx12mm - 02 Nos per leaf. (f) MS pintel hinges size 75mmx12mm - 2 Nos per leaf (g) MS Guard bars 10mm square bar @ 10Cm C/C fixed horizontaly. (h) 3mm thick clear sheet glass 3 nos per glazed leaf of reqd sizes glazing with oil putty. (j) Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples to each gauged shutters of window. (k) Filling hold fast blocks with PCC 1:2:4 type B1 (using crushed stone aggregate, minimum four number of each frame ) and (l) Repair all the damaged surfaces around window with plaster & other finishes to matches the surfaces with as per existing specifications complete.
Material and Labour for Box type steel ventilator made of ERW tube P-section of size 60mmx25mm outer frame (single rebated), comprises glazed shutter, frame of ERW tube and FI 2mm thick welded/screwed to frame for fixing of sheet glass with & including 3mm thick Sheet glass glazing with oil putty, MS Guard bars 10mm square bar @ 10Cm C/C fixed horizontaly, fixture and fittings like as Stopper, Cleat, Pintal hinges, hold fast etc all as shown on drg No CEJZ/TD-1019/08 sheet 1/3 to 3/3 dt 01 May 2008 , including Filling hold fast blocks with PCC 1:2:4 type B1 (using crushed stone aggregate, minimum four number of each frame ) and repair all the damaged surfaces around ventilators with plaster & other finishes to matches the surfaces with as per existing specifications complete.
Supply & Fixing for 35mm thick 2nd class hard wood panelled shutters (two panels) Factory Made with lock rail & panel of 9mm BWP commercial ply or 12mm thick vineered particle board with commercial vineering on both faces, the size of rail & styles as per IS: 1003 (Part-I) klin seasoned & chemically pressure treated (factory made shutters) ; complete all as specified and directed by the Engineer in Charge
Supply and Fixing for 30mm thick 2nd class hard wood glazed and skeleton shutter’s open rebated prepare to receive glass gauge etc edges of framing plain chamfered or rounded fitted with Cut and mitered bead’s for securing glass gauge etc size of mamber of shutters as per SSR Part-I Section-8 clause 8.2 (a) complete all as specified and directed by the Engineer in Charge.
Supply & fixing 18 mm thick solid PVC ply of 1st quality of apprvoed colour fixed with screws, solvent cement / adhesive to make kitchen cabinate, shelves and cupboard shutters/shelves ; complete all as specified and as directed by the Engineer-in-Charge.
Supply and Fixing for 20mm thick PVC shutter, printed one side with one coting of ultra violet chemical, glossymat finish inc 100% termite/water proof, fireretrandenteco friendly. Weight not less than 12 kg per sqm incl Steel piano hinges, steel catcher,aluminium handle100 mm long ,aluminium hasp & stapple in repair complete all as specified ( shade / design / size as approved by Enginner -in-Charge) complete all as specified and directed by the Engineer in Charge.
Supply and Fixing for 3mm thick ordinary sheet glass and glazing with oil putty or fixed on steel frame, in squares not exc 0.50 Sqm in each panes , including Hacking out old broken glass any thickness, size, quality or description from steel frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads Complete all as specified
Supply and Fixing for stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples ; complete all as specified and directed by the Engineer in Charge.
Supply and Fixing in repairs for stainless steel wire cloth 0.56mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks or stainless steel wire staples ; complete all as specified and directed by the Engineer in Charge.
Supply and Fixing for 300 mm size, aluminium alloy,anodized sliding door bolt, clip type, and fixing clips of sheets or extruded section and fixing of bolts and sliding bolts of extruded section fixed with stainless steel screw ; complete all as specified and directed by the Engineer in Charge.
Supply and Fixing for butt hinges 100mm size medium weight cold rolled mild steel fixed with stainless steel screw complete all as specified and directed
Supply and Fixing in repairs 150 mm size aluminium anodized barrel tower bolt of extruded section fixed with stainless steel screw ; complete all as specified and directed by the Engineer in Charge.
Supply and Fixing in repairS 300mm mild steel ordinary rat tail rod pattern spring including roller plate including fixing with nailsd/ bolts or welded compete all as specified.
Supply and Fixing in repairs 125 mm size extruded aluminium anodized handle cast type fixed with stainless steel screw ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing for mild steel powder coated curtain rods 25mm dia ( as per sample kept in GE's office) including knobs, brackets to hold the rod & a set of ABS finials ( as per sample kept in GE's office) of approved quality & appropriate qty of ABS plastic rings complete all as specified .
Material & Labour for Preparation of new wooden surface over 10 cm width or girth and applying two coat of synthetic enamel paint over one coat of pink primer ; complete all as specified and directed by the Engineer in Charge.
Material and labour for preparation of old painted wooden surfaces of any description, over 10 Cms width or girth and applying one coat of synthetic enamel paint ; complete all as specified and directed by the Engineer in Charge.
Material and labour for applying two coat of synthetic enamel paint over a coat of red oxide, zinc chrome primer on steel surfaces exceeding 10 cm width or girth including preparation of new surfaces ; complete all as specified and directed by the Engineer in Charge.
Material and labour for preparation of old painted steel surfaces of any description, over 10Cms width or girth and applying one coat of synthetic enamel paint ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing for galvanized iron steel tubing medium grade 15mm bore with all fittings and fixed Complete all as specified to walls, ceiling or laid in floor ; including disconnecting , taking up or down steel water tubing and connections including cleaning serviceable pipe for refixing and removal of unserviceable pipe, including necessary excavation and earth work, cutting/ chasing in wall/ floor and making good disturbed surfaces in cement mortar 1:3 to the entire satisfaction of the engineer in Charge ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing for galvanized iron steel tubing medium grade 20mm bore with all fittings and fixed Complete all as specified to walls, ceiling or laid in floor ; including disconnecting , taking up or down steel water tubing and connections including cleaning serviceable pipe for refixing and removal of unserviceable pipe, including necessary excavation and earth work, cutting/ chasing in wall/ floor and making good disturbed surfaces in cement mortar 1:3 to the entire satisfaction of the engineer in Charge ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing for Grating round 140mm size of PTMT ( minimum weight 50gms) ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing in repairs PVC connection 450mm long of 15mm size with PTMT nuts on both sides ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing for bib tap standard 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-90gms) ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing for Pillar taps 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-110gms) ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing in repairs stop valve 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-90gms) ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing in repairs stop valve 20mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 20mm-92gms) ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing in repairs angle valve 15mm bore of PTMT any colour high pressue screwed for iron pipe and fixed ( minimum weight 15mm-90gms) ; complete all as specified and directed by the Engineer in Charge.
Supply and Fixing in repairs for 15mm bore stop valves, cast copper alloy, concealed type, chromium plated with long shank and cup ,screwed down,handles, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed by Engr-in-Charge.
Supply and fixing in repairs for viterous chinaware wash hand basin light colour/white of size 550mmx 400mm flat back or angle stay, brass chromium plated waste coupling, chain, plug, porcelain rubber stopper, brackets, 32mm bore PVC waste pipe of appropriate length including disconnecting , taking out of old WHB & making necessary connections ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing in repairs for rotational moulded polythelene water storage tanks (Three layers) ISI marked capacity 1000 litres(cylindrical vertical with closed top), with and including 20mm dia PTMT ball valve with epoxy coated aluminium rod ( minium weight 210gms ) hoisted, fixed in position and making connection including disconnecting , taking out of old unserviceable water storage tank & making necessary connections ; complete all as specified and directed by the Engineer in Charge.
Supply and fixing for Towel Rail 600mm long of PTMT fixed with and including chromium plated brass screws and wooden/ plastic cleats (Minium weight 190 gms) ; complete all as specified and directed by the Engineer in Charge.
Material and Labour for 25 mm thick PCC 1:2:4 type B-0 using 12.5mm graded stone aggregate as in sub base and finishing the surface even & rough to receive floor finish ; complete all as specified and directed by the Engineer in Charge.
Roughening of surfaces of old concrete floor, sweeping, clean and washing with water to remove dust ; complete all as specified and directed by the Engineer in Charge.
Dismantaling floor hearth or wall tiling incl cement mortar bedding (but not backing ) removing serviceable tiles to store and rubbish off the premises.
Material & Labour for Coloured/printed glazed creamic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.16 sqm,thick in vertical surfaces (skirting/dado), over & including 10mm thick cement plaster in cement mortar 1:4 complete all as specified and directed by the Engineer in Charge.
Material & Labour for Coloured/printed non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0. 11 sqm but not exceeding 0.18 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or Coloured cement to match over & including 15 mm thick screed bed or bedding layers in CM 1:6. ; complete all as specified and directed by the Engineer in Charge.
Demolition of cement concrete in ground floors and paving not exceeding 15 cm thickness ( below or above ground level) and disposing the rubbish to a distance exceeding 50 Mtr but not exceeding 100 Mtr away to low lying areas ; complete all as specified and directed by the Engineer in Charge.
Material & Labour for 50mm thick Cement concrete type D-2 , 1:4:8 (40 mm crushed stone graded aggregate) as in sub base of floor surfaces finished even & fair ; complete all as specified and directed by the Engineer in Charge.
Material & labour for 16-20mm thick machine cut kota stone slab flooring with Kota stone of size 580mm X 580 mm , laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab ; over and including 20mm thick screed bed in cement mortar 1:6 , with & including cutting, rubbing and mirror polishing to the entire kota stone slab flooring with rubbing machine using suitable size of cutting stones to the entire satisfaction of the AGE , complete all as specified and directed by the Engineer-in-Charge.
Material & labour for 16-20mm thick machine cut kota stone slab in riser of steps, skirting, dado and pillar with Kota stone of size 580mm X 150 mm , laid & jointed with grey cement slurry mixed with pigment to match the shade of the slab ; over and including 10mm thick screed bed in cement mortar 1:4 , with & including cutting, rubbing and mirror polishing to the entire kota stone in riser of steps, skirting, dado and pillar with rubbing machine using suitable size of cutting stones to the entire satisfaction of the AGE ; complete all as specified and directed by the Engineer-in-Charge.
Dismantling of PVC/CI pipe of 75/100mm dia fixed with cement joint ; complete all as specified and directed by the Engineer-in-Charge.
Supply & Fixing for PVC (SWR) pipes 110mm dia single socketed in any length with rubber ring joints fixed to walls ; complete all as specified and directed by the Engineer-in-Charge.
Supply & Fixing for PVC (SWR) 110mm dia bend any radius ; complete all as specified and directed by the Engineer-in-Charge.
Supply & Fixing for PVC (SWR) pipes 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed by the Engineer in Charge.
Supply & Fixing for PVC (SWR) gully trap 125/110mm setting and jointing with solvent cement.
Supply & Fixing for 110mm bore PVC (SWR) branch piece , single, equal fitted with oval access doors complete all as specified and directed by the Engineer in Charge.
Material & Labour for PCC type D-2 (1:4:8) using 40mm graded crushed stone aggregate as in in foundations, filling and mass concrete , sub base etc and similar works ; complete all as specified and directed by the Engineer in Charge.
Material and labour for 22 to 25mm thick machine pressed coloured chequered cement concrete tiles ISI Marked of size 300mm x 30mm over and including 15mm thick cement screed in CM 1:6 set and jointed in neat cement slurry and pointed with white cement mixed with pigment to match the colour of tiles ; complete all as specified and directed by the Engineer in Charge.
Material and labour for repairing of RCC projection, chajjas, facia,bands, shelves, beams, RCC railing, balcony and similar works by dismantling of loose/ disintegrated portion RCC at any height and in any sitution floor (including provn of support, formwork and welding of reinforcement if required with wire mesh of eight 1.5 kg/ sqm and dubbing/ filling with PCC (1:2:4), type B-0, using 12.5 mm graded aggregate,15 to 25 mm thick after applying cement slurry @ 3 kg/sqm, finished even and smooth to desired shape and applying two coats of wheater proof emulsion paint to match with existing surfaces complete all as specified and directed by the Engineer in Charge.
Material & Labour for PCC type E-2 (1:5:10) using 40mm graded crushed stone aggregate as in in foundations, filling and mass concrete , sub base etc and similar works ; complete all as specified and directed by the Engineer in Charge.
Dismantling of brick tiles single layers on roof, jointed and grouted / pointed in cement mortar including cleaning serviceable tiles and stacking properly for re-use, disposal of unserviceable tiles and debris /rubbish from site ; complete all as specified and directed by the Engineer in Charge.
Demoliton of mud in roof any thickness including mud plastering and removing to distance exc 250m but n exc 500m ; complete all as specified and directed by the Engineer in Charge.
Material and labour PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in roof kerbs,roof sloping padding and finishing the surface even and smooth (without using extra cement) ; complete all as specified and directed by the Engineer in Charge.
Material and labour for applying evenly a tack coat of industrial bitumen 85/25 grade @ 1.2 Kg/Sqm includingcleaning surfaces etc ; complete all as specified and directed by the Engineer in Charge.
Material and Labour for cleaning of dust & dirt , removal of all loose dirt / material & applying heat torch gun over bitumen to get smooth plain finished surface and providing & applying APP based polymeric membrane minimum weighing 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric ( Wt not less than 150 gms /sqm ) laid on bituminous surfaces by forced application over entire roof area, sunken portion with overlapping 100mm to eiher side ; complete all as specified and directed by the Engineer in Charge.
Material and labour for 40 mm thick brick tiles laid over and including 15mm thick bedding layer in cement mortar 1:6 and jointed, grouted and flush pointing as work proceed in CM 1:3 mixed with 5% of crude oil by weight of cement ; complete all as specified and directed by the Engineer in Charge.
Material and labour for brick tiles (Except brick tiles, serviceable brick tiles obtained from demilition shall be used) laid over and including 15mm thick bedding layer in cement mortar 1:6 and jointed, grouted and flush pointing as work proceed in CM 1:3 mixed with 5% of crude oil by weight of cement ; complete all as specified and directed by the Engineer in Charge.
Material and labour for udaipur green marble 16-18mm thick confirming to sample kept in GE 's office ( table rubbed and polished inslab, stair case, step and like jointed with grey cement slurry mixed with pigment to match with shade of marble over and including 15mm thick cement screed bed in CM (1:6) complete all as specified
Material & labour for MS Framed work as in doors or gates or grills of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing of Fe 410-W (GdeE- 250) quality-A complete complete all as specified and as directed.
Material and labour in repairs for cast iron floor trap ( long nose) 75mm bore with grating including Jointing to waste pipe fixed in PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) ; complete all as specified and directed by the Engineer in Charge.
Excavating in post holes (or similar holes) each hole not exceeding 0.5 Cum, getting out, returning,filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and remvoing surplus soil to a distance not exceeding 50m and making good surfaces in hard/dense soil ; complete all as specified & directed by the Engineer-in-Charge.
Supply & Fixing for Steel work in tubular trusses including special shaped washer , gusset plates, nuts , bolrs etc. complete using ERW or induction butt welded tubes conforming to I.S 1161-1979 grade St. 240 ; complete all as specified & directed by the Engineer-in-Charge.
Supply & Fixing for Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws ; complete all as specified & directed by the Engineer-in-Charge.
Material and labour for Cutting , Polishing , rubbing & finish mirror polishing to the entire kota stone slab flooring with rubbing machine using suitable size of cutting stones to the entire satisfaction of the AGE ; complete all as specified and directed by the Engineer-in-Charge.
Supply & Fixing pressed steel frames 1.25mm thick for door size of frame 125 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges complete all as specified and directed.
Material and labour for RCC 1 : 1.5 : 3 using 12.5 mm mm graded stone aggregates as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like ; Complete all as specified and directed by Engineer-in-Charge.
Material and labour for Mild steel TMT bars 10 mm dia., and over cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia., or securing with clips ; complete all as specified and directed by the Engineer-in-Charge.
Material and labour for use & waste of Fair finished flat form works to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) ; complete all as specified and directed by the Engineer-in-Charge.
Supply & Fixing for pressed steel frames 1.25mm thick for door size of frame 105 x 60mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate and tarring to inner surface (surface in contact with concrete/brick surface) of chowkats and hinges ; Complete all as specified and directed by Engineer-in-Charge.
Taking down carefully copper/aluminium point wiring light, fan, socket or power complete, such as switches, ceiling roses, pendents, regulators, sockets etc. removing materials to store for keeping in safe costudy or for taking credit and making good disturbed surface of walls, floors etc ; Complete all as specified and directed by Engineer-in-Charge.
Material & labour for Point wiring for one light point / fan point / bell point point , controlled by one, one way switch with 1.50 Sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FR) (using colour code as per IS) drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing specifications) and sunk cast iron or pressed steel terminal boxes for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of 1.50 Sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FR) as in earth wire (using green colour) and connected to common earth dolly, including making good of disturbed surface of cement plaster, whitewash/ distemper to match with original colour ; complete all as specified & directed by Engineer-in-Charge.
All as per item No 84.00 above but one 5 Amp 3 pin socket outlet on independent board complete.
All as per item No 84.00 above but one 5 Amp 3 pin socket outlet on the same board with other switches complete.
Material & labour for Point wiring for one 16 Amp socket outlet point (independent point), controlled by one, one way switch with 2.50 Sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FR) (using colour code as per IS) drawn into and including medium grade PVC conduit concealed (not less than 20 mm dia) all necessary fittings and accessories fixed concealed (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing suface) and sunk cast iron or pressed steel terminal boxes for mounting fitting like switches, sockets, lamp holders, sketch fittings and covered with 3 mm thick plastic laminated bakelite sheet cover fixed with brass screws and cup washers including one continuous run of 2.50 Sqmm size PVC insulated unsheathed 1100 volts grade single core (multi-stranded) copper conductor cable (FR) as in earth wire (using green colour) and connected to common earth dolly, including making good of disturbed surface of cement plaster, whitewash/ distemper to match with original colour ; complete all as specified & directed by Engineer-in-Charge.
Supply & fixing for switch piano 5 amps flush type single pole one way complete all as specified and directed by Engineer-in-Charge.
Supply & fixing for socket outlet flush type 2 in one 5 pin 6 amps complete all as specified and directed by Engineer-in-Charge.
Supply & fixing for switch piano 15 amps flush type single pole one way complete all as specified and directed by Engineer-in-Charge.
Supply & fixing for socket outlet flush type 2 in one 5 pin 16 amps complete all as specified and directed by Engineer-in-Charge.
Supply & Fixing in repairs fan regulator electronic step type (5 step) socket size and making all necessary connections complete all as specified and directed by the Engr-in-Charge.
Supply & fixing for Ceiling rose surface bakelite 65 mm x 50mm, two to three terminals with back plate of 3mm thick bakelite laminated hylem sheet of suitable size ; complete all as specified and directed by Engineer-in-Charge.
Supply & fixing for lamp holder PVC/ polycarbonate type with back plate suitable for batten fittings complete all as specified and directed by the Engineer in Charge.
Supply & Fixing in repairs wall/ceiling mounting LED 18 Watts tube light complete with accessories 1 x 18 watts LED, CCT of 6500 K, CRI >=80, THD <=20%, and lumen output 1810 Lm having intergrated electronic driver (SMPS based) with open ckt/output short ckt protection and surge protection suitable for domestic application 240 volts internally prewired with 1.5 sqmm twin twisted copper wire and connection ; complete all as specified and directed by the Engineer in Charge.
Supply & Fixing in repairs energy saving new generation 10 Watt LED built up made up of Injection moulded Polycorbonate housing with high Quality Polycarbonate UV Protected Milky diffuser having CCT of 6500 K, THD<=15, CRI>=80, integrated electronic LED driver with APFC and 3.5 kv inbuilt surge protection with complete accessories and connection ; complete all as specified and directed by the Engineer in Charge.
Material and labour in repairs submain wiring with two single core PVC insulated multi stranded copper conductor cable FR of size 4 Sqmm 1100 volt grade (ISI marked ) drawn through and including non metalic PVC conduit pipe medium grade ISI marked (not less than 25 mm dia) along with fittings and accessories all fixed concealed on wall and surface on ceiling, with one 4 Sqmm single core multi stranded copper conductor FR as earth continuity to common earth doly as earth wire (Green colour) complete all as specified and directed by the Engineer in Charge. Note : Two runs of main wire and one run of earth wire with PVC conduit shall be measured and paid as one length.
Supply & fixing in repairs MCB single pole 240 Volts, 50Hz,vrupturing capacity 10 KA , B curve , conforming to IS 8828 of rating 6 to 32 Amps complete all as specified and directed by Engineer-in-Charge.
Supply & Fixing in repairs security light fitting LED 36Watt made up of pressure die cast aluminium housing and toughned glass having bottom opening separate driver with IP 66 Protection and Impact resistance of IK07, THD<=10%, Lumen output – 2700 Lm, CCT 6500 K, CRI>=70, with & including suitable size GI light grade pipe 1metre long bend to shape with MS clams,nut , bolts and accessories complete including connection with 3 core PVC insulated overall sheated with flexible cable multistrand copper conductor of size not less than 1.5sqmm from ceiling rose to connector to fitting terminal including taking down old security light fitting ; complete all as specified and directed by the Engineer in Charge.
Supply & Fixing for GI bracket 1.2 metres long, made of GI pipe medium grade of 40 mm dia, 2 x clamps made of Flat iron 40 mm x 6 mm Incl nuts,bolts & washers, painting, fixing on wall of the building/ pole complete all as specified and directed by the Engineer in Charge.
Supply & Fixing in repairs MCCB Incomer distribution board double door vertical type made out of CRCA MS sheet surface with insulated material like polyester or with epoxy powder coating surface mounting TPN 4 way, 415 volts with copper bus bar rating 200 Amps, dust and vermin proof suitable for incorporation of MCCB and IP 43 - IK 09 protection with and including 100 Amp 36 KA 4 pole MCCB with thermal - magnetic setting and Icu = Ics = 100% , including suitable type MCb with blank plate complete all as specified. Note :- The cost of removing old wooden/steel any type box and making good of surface as original by brick work, plastering, whitewash/colour/distemper etc is included in quoted rate)
Supply and fixing Ceiling fan 1200 mm sweep BEE 5star rating complete with down rod including fitting and fixture as per site requirement and complete accessories 230 volts single phase 50 Hz AC and connecting up with and including two core PVC insulated PVC sheathed copper conductor cable of required size & length complete all as specified and directed by the Engineer-in-Charge.
Supply and fixing Exhaust fan 300mm sweep including fitting and fixture as per site requirement and complete accessories 230 volts single phase and connecting up with and including two core PVC insulated PVC sheathed copper conductor cable of required size & length , with and including cutting in brick/stone masonery wall and make opening as per site for fixing exhaust fan making good of disturbed surface of cement plaster, whitewash/ distemper to match with original colour complete all as specified and directed by the Engineer-in-Charge.
M/S RASHPAL CONSTRUCTION CO
amardeep traders
m/s inder construction co
GEE EMM ASSOCIATES
ESS KAY BUILDER
M/s. M Company
Harai Sharan Govt Contractor
MAAN ENTERPRISES
B.J.CONSTRUCTION CO
stage.html
html • 0.07 MB
tech_bid_open.pdf
tech_eval.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
aoc.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .