SPECIAL REPAIR TO BUILDING NO ET 41, BCD 103 AND 104 INCLUDING PROVISION OF APPROCH PATHWAY NEAR BCD 102 AND 103 OF ASC CENTRE AND COLLEGE UNDER GE CENTRAL BANGALORE

Amount

B/R PORTION/WORKS : Dismantling of single layer mangalore pattern or similar type tiles in roof coverings including ridges complete as directed. (measured flat overall)

Dismantling timber boarding, any description, fixed in any position with nails complete all as specified and directed.

Demolition of plain cement concrete (unreinforced) in ground floors, plinth protection/path/pavings etc not exceeding 15 cm thickness. (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Demolition of reinforced cement concrete any description and in any position not otherwise specifically provided for etc (Manhole cover/slab), cutting reinforcement steel to facilitate demolition of concrete including removing the materials out side MD land complete all as specified and directed.

Dismantling timber scantlings 40 Sq.cm and over in section (unframed work), in any position complete all as specified and directed.

Dismantling of timber batten for roof tiles, sheets etc of any size including tilting fillets in section in any position fixed with nails spaced exc 15 cm

Demolition of brick work or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars etc and removing debris outside MD land complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness including frame work, cover fillets and cleaning, stacking old serviceable materials safely at site for reuse at site complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water and removing debris outside MD landcomplete all as specified and directed

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and disposing serviceable tiles to MES store and the rubbish/debrises out side MD land complete all as specified and directed.

Taking down chowkats or frame, not exceeding 1.5 Sqm in each with shutters (without taking off shutter from the frame) complete all as specified and directed.

Taking down chowkats or frames, exceeding 1.5 but n.exc. 4 Sqm in each with shutter (without taking off shutter from the frame) complete all as specified and directed.

S & F 20 mm thick, second class hard wood boarding, clean sawn, planed one side with butt joints and fixed with nails in any situation as in eaves board, etc complete all as specified and directed.

S & F second class hard wood scantling, clean sawn timber fixed with nails etc complete all as specified and directed.

S & F second class hard wood, clean sawn timber batten sectional area exc 5 sq.cm but not exc 15 sq.cm at 30 cm centre to centre fixed with nails etc complete all as specified and directed.

Surface excavation n.exc 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil.

M & L for pressed steel frame of size 120X60 mm made out of 1.25mm thick plain black steel sheet (CRCA) for door with one or more rebates including fixing by welding necessary lugs, hinges, lock plate and PCC filling into frame using plain cement concrete 1:3:6, type C1 etc complete all as specified and directed. NOTE : - Butt hinges shall be measured and paid separately as supply only under respective item BOQ.

M&L for 35 mm thick 2nd class hard wood factory made glazed/gauzed skeleton shutters for door, open rebated and prepared to receive glass, gauze etc (without sash bars), edges framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass/gauge etc; size of the members of shutters as specified in SSR Part- I, Section 8, clause 8.24(a) complete all as directed.

S&F 30mm thick Flush shutters, solid core construction, with block coard core & plywood face panels commercial type on both side conforming to IS 2202 (Part- I) -1999, including internal liping beading all round fixed as in Door Shutter,Cup board shutter & Kitchen rack all as specified.

S & F box type steel windows/ventilators double side shutters ie glass and wire mesh shutter, including pressed steel frames made out of CRCA sheet of 80X60X1.25mm thick double rebated, shutters box type made out of CRCA sheet of 40X20X1.0mm thick, 12mm square guard bar/grill welded to steel frame, window shutters side hung, ventilator shutters top hung, box type hinges, aluminium die cast handles for glass shutters, iron flat type handles for mesh shutters, telescopic stays etc complete all as specified in TD drawing No TD/539 dated 09.02.2004 of Chief Engineer Chennai Zone and as directed. NOTE:- (i) Qouted rate under this item shall deemed to be inclusive of steel frame, both side steel shutters, guard bars/grills, handles, stays, beading/fillets for fixing glass/wire mesh including cost elements for fixing of glass & wire mesh and mearurement/ pament shall be considered as one unit by comprising all these elements. (ii) Glass and wire mesh shall be measured and paid as supply only underseparately under respective item.

Supply only 5.5 mm thick, sheet glass, ordinary quality including oil putty/timber beads in square exceeding 0.5 Sqm in each pane complete all as specified and as directed.

Supply only stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

S & F 4 mm thick, sheet glass, ordinary quality and glazing with oil putty/timber beads in square not exceeding 0.5 Sqm in each pane complete all as specified and as directed.

S&F for stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples, complete all as specified and directed

S & F solid PVC door frames of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube complete all as specified and directed.

S & F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails. MS frame shall be covered with heat moulded, plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet 5mm thick to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, as per specification and drawing and as directed.

Supply only 100 mm size, butt hinges, medium weight, cold rolled complete all as specified, and directed.

S & F 100 mm size, butt hinges, medium weight, cold rolled complete all as specified, and directed.

S & F 100 mm size, butt hinges for PVC door, stainless steel with cadmium coated screws complete all as specified and directed.

S & F 200 mm long, Aluminium, barrel tower bolts of extruded section of aluminium alloy, anodised finish not be less than Grade AC 10 of IS 1868:1996 with transparent anodic film complete all as specified and directed.

S & F 150mm size, Aluminium handles, cast type, anodised to a bright natural, mat finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S & F aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm anodised finish not be less than Grade AC 10 of IS 1868:1996 complete all as specified and directed.

S&F for pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick (Total coated thickness) of any colour, finished with resin coat on both surfaces @ 150 gm/sqm of coating (total both surfaces) having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with best quality self tapping screws as specified

S & F Pre-Painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/valley gutter, fixed with self tapping screws complete all as specified and directed. (Colour of ridge shall be same colour as that of sheet used for roof)

S & F for false ceiling of 4mm thick HSPC (High Presure Steam Cured) pre-primed self embossed texured designer ceiling board, cement fibre board of size 595X595 mm (E-Board Classic, white colour) to be fixed in and including GI snap grid with rool formed out of hot dip galvanised steel capings (Powder coated finished) 600X600 mm system. The suspension system consisting of perimeter wall angle of size 38X24X0.90mm of thick GI sheet to secure on wall portion fixed with the help of rawl plug @ 450mm centre to centre universal main runner of T shaped section with single rotary stitching of size (32X24X0.9 mm) made from 0.0.9mm thick GI sheet of length 3.60 metre to be spaced @ 1200 centre to centre cross runner T shaped with double rotary stitching of size (28.6X24X0.9 mm) of length 1200mm made from 0.90 mm thick GI sheet spaced @ 600mm centre to centre (1200X600mm) of size module intermadiate T shaped cross runner of size (28.6X24mm) of length 600mm made of 0.0.90mm thick GI sheet to form (600X600mm) size of module including suspension of the ceiling from the roof/structural members, soffits angles, cleats, by using GI suspenders of 3mm dia GI wire and level adjusters including U clamp of GI fixed in ceiling all complete and making opening by cut out the ceiling board for ceiling light fittings as required and as per manufacturer's instruction or as directed by Eng-in-charge. Make :- Eternit Everest / lafarge/ Armstrong or equivalent as approved by GE

All same as item No 35 above but using old serviceable materials. NOTE :- Old serviceable ceiling materials retrieved under item No 08 shall be used.

M & L for Hardcore of broken/crushed stone aggregate of gauge n.exc 63 mm deposited, spread and levelled in layers not exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for 75mm thick Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in sub base of floor, etc complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection laid in proper slope/gradient etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for precast chequered cement concrete tiles of size 20cm x 20cm x 25mm thick, as in floors etc, including 20 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in grey cement and pigments to match with the shade of tiles complete all as specified and directed.

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in base of flooring, padding over roof/ chajja etc and finished the surface fair to receive top layer screed bed complete all as specified and directed.

M & L for Plain cement concrete 1:2:4, type B-0, (using 12.50 mm graded stone aggregate) as in coping, kneelers, bed plates etc including weathering slightly rounded or chamfered angles including necessary form work complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles, Grade B II(a), 8 to 10mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.36 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for ceramic, coloured tiles 8 to 10 mm thick as in skirting/dado/vertical surfaces to match the length of floor tile procured under No 43 above including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles, Grade B II(a), 7 to 8mm thick (square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, in floors etc, including 15 mm thick screed bed in cement mortar 1:4 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed ceramic, coloured tiles, Grade B III, 7 to 8 mm thick area of each tiles not less than 0.06 sqm as in skirting/dado/vertical surfaces including 10 mm thick screed bed in cement mortar 1:3 set & jointed in neat cement slurry and pointed in coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Precast Reinforced Cement Concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in cover slab of drain, etc and set in cement mortar 1:4 including necessary form work, moulds, etc complete all as specified and directed by the Engr-in-Charge. (Note : Reinforcement shall be measured and paid separately)

S & F TMT steel bars 6 to 10mm dia, cut to length, bend to shape required, including cranking, bending spirally as in tie/stirrups of columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

M&L for precast cement concrete block masonry type C1, 1:3:6 (20 mm graded granite stone aggregate) with solid blocks, exc 10 cm in width and setting in cement mortar 1:6 complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 15 mm thick in two layer (10mm + 5mm thick) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with water proofing compound at top 5mm thick layer by weight of cement as per manufacturer's instructions and finished the surface even and smooth without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

"Supply only" liquid water proofing compound complete all as specified and directed. (Make : Dr FIXIT/Fosroc/choksey)

M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over 1 to 2mm thick wall care putty over a coat of primer complete all as specified and directed.

M & L for preparation newly plastered surfaces of wall, chajja, facia etc and applying two coats of acrylic (antifungal) exterior grade paint over a coat of primer all as directed.

M & L for preparation old decorated external surfaces of wall, chajja, facia etc and applying two coats of acrylic (antifungal) exterior grade paint over a coat of primer all as directed.

M & L for preparation of new plastered surfaces of walls and applying three coats of white wash complete all as specified and directed.

M&L complete removal of existing treatment and applying two coats of distemper oil emulsion over a coat of primer to plastered and other surfaces including providing wall care putty two coats in minimum 1mm thick on plastered surface complete all as specified.

M & L for preparing old plastered surfaces of walls by complete removal of existing treatment and applying two coats of white wash complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of creosote oil complete all as specified and directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified and directed.

Taking up or down 15mm bore, Steel tubing and connections.

Taking up or down 20mm bore, Steel tubing and connections.

Supplying and laying of 16mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors/trenches complete all as specified.

Supplying and laying of 20mm dia CPVC pipes (ISI marked) SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors/trenches complete all as specified.

S & F in repair Vitreous China urinal, bowl type, flat back, size 465X355X265mm (Appx size), white with grating and union for discharge pipe (excluding flushing cistern, flush pipe & waste pipe) including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60 mm long brass screws, pointing around urinal back in cement complete complete as specified and directed. (Make: CERA Cat No S4020104 or equivelant of Parryware /Hindware/PRAYAG)

S & F in repair Vitreous China (white) urinal partition of approximate size 90X320X720 mm. Make CERA Cat No S4090101 or equivelant of make Parryware/Prayag/Hindware as approved by GE.

S&F in repair Vitreous China Wash hand basin , white flat back size 550x400 mm including a pair of mild steel angle iron brackets duly painted, erected/embeded in wall, 32 mm waste coupling brass chromium plated suitable for wash hand basins & 32 mm dia LDPE PVC waste pipe including cutting hole and pinning in ends making good disturbed portion using cement mortar 1:3 complete all as specified & directed by Engineer-in-charge. Make of basin CERA Cat No S2040105 or equivelent of Parryware/Hindware/Prayag

S&F in repair Vitreous China Squatting Pan"Orissa pattern" size 580 mmx440 mm white with integral foot rest S or P trap etc. including connector & Provision of concrete bedding and making good to floor all as specified & directed by Engineer-in-charge. Make of Pan CERA Cat No S3010108 and of cistern B1010109 or equivelent of Parryware/Hindware/Prayag

S & F in repairs, 10 litre capacity, PVC valve less syphonic action type, flushing cistern, low level, white, with inlet, ball valve, flush pipe, float and handle brackets including 15mm dia 600 mm long, PVC connection pipe with PTMT nut and washer complete all as specified and directed. Make CERA Cat No B1010109 or equivelent of PRAYAG/HINDWARE/Parryware

S&F in repair pillar taps, 15 mm, brass with capstan heads, fancy type, chromium plated, screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and flynuts screwed for 15mm bore iron pipe and fixed in repair, complete all as specified and directed. Make PRAYAG Cat No 7202 or equivelent of CERA/PARRYWARE/HINDWARE as approved by GE.

S&F in repair 15 mm bore bib taps cast copper alloy chromium plated with capstan head screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO HT-F3001151 or equvelent of Make Hindware/Parryware/PRAYAG

S&F in repair 15 mm bore stop valves/angle valve cast copper alloy chromium plated fancy type with long shank and cup, concealed type, screwed down to iron pipe complete all as specified and directed. Make: CERA Cat NO HT-F3001201 or equvelent of Make Hindware/Parryware/PRAYAG

S & F in repair brass chromium plated tubular towel rail, 20mm dia 'D' type, 600mm long between flanges complete all as specified and directed. (Make: PRAYAG Cat NO BA-01 or equivalent of Parryware /Hindware/Cera)

S & F swival shower of PTMT 15mm bore (minimum weight 40 gms) including shower arm 15mm size, 225mm long with bend of 45 degree with flange of PTMT any colour (minimum wt 40 gms) complete all as specified and directed. Make Prayag or equivelent as approved by GE

S & F in repairs PVC connection pipe with PTMT nuts, 600 mm long. Make: CERA/Hindware/Parryware/PRAYAG

S & F in repairs PVC 32mm dia waste pipe for basin, sink, and urinals etc with long screwed shank and fly nuts, flange end all as directed.

Dismantling of rotational moulded polyethylene water tank of capacity exceeding 500 Litres but not exceeding 1000 Ltrs.

S&F rotational moulded polyethylene water storage tanks 1000 litre capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part-I including 20 mm dia brass ball/float valve high pressure with polythene float and flynut, 20 mm water tank nipple suitable for HDPE water tank, 20mm bore gun metal gate/globe valve with iron wheel head complete all as specified and directed.

S & F 110 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall using MS holder bat, etc complete all as specified and directed.

S & F 75 mm bore, UPVC (SWR), Type 'B', Soil waste and vent pipes in any length without ears, with solvent cement joints fixed to wall, using MS holder bat etc complete all as specified and directed.

S & F 110 mm bore, PVC (SWR) bends of any radius with acess door complete all as specified and directed.

S & F 75 mm bore, PVC (SWR) bends of any radius with acess door complete all as specified and directed.

S & F 75 mm dia outlet , PVC (SWR) floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

E/M PORTION/WORKS : Taking down copper/ aluminium point wiring(light, fan, socket or power) complete, including fittings and fixtures such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions seperately) and making good distrubed surfaces of wall, floors, etc complete.

Point wiring with PVC insulated and unsheathed FRLS cable single core multistranded copper conductor 1.5 sqmm size, 1100 volts grade cable conforming to IS-694 1990 drawn in and including grey colour PVC rigid non metalic conduit (Medium Grade) on surface conforming to IS-9537 with all accessories including fabricated MS terminal boxes fixed flush with wall surface with 3mm thick laminated sheet top cover fixed with brass screw for mounting switches, sockets, regulator etc including 1.5 sqmm single core PVC insulated and unsheathed copper conductor earth continuity conductor to common earth and connecting to earth dolly all as specified for :- One light/fan point controlled by one 5 Amps switch one way

All as per item No 87 above/here-in-before but for one 3 pin socket point 5 Amp on independent board

All as per item No 87 above/here-in-before but for one 3 pin socket point 5 Amp on same board with other switches.

All as per item No. 87 above but with 2.5 sqmm ( Nominal area ) cable with 2.5 Sqmm size copper earth continuity conductor for 3 pin 15 A socket outlet on independent board complete all as specified and directed.

Supply and fix Switch piano, flush button single pole, 5 Amps one way.

Supply and fix Switch sokcet combination flush type 5 Amp 2/3 pin muliti purpose

Supply and fix Switch socket combination flush type 5/15 Amps 3/3 pin universal multipurpose

Supply and fix Fan regulator electronic, step & socket type 230 volt, suitable for 1200/1400mm sweep ceiling fan.

Supply and fix Ceiling rose surface bakelite 65x50mm three terminals including supply and fix PVC blocks.

S&F in replacement LED tube light fitting of 20 watts 6000K , 230 volt, with aluminium extruded channel powder coated with diffuser for glare free light complete with all fixing accessories such as 2 nos of PVC square/round boxes, screws, etc and connecting up with three core flexible copper conductor cable of size 24/0.20 sqmm complete all as specified and directed by Engr-in-charge. Make : Havells Cat No LUMILINEBS20WLED865SPCWH OR equivelant of make Shakti/Crompton Greaves/Bajaj

S&F new generation energy saving environmental friendly long life, with high power LED building street light/security light 1x 25 Watt LED pressure die-cast aluminium, heat resistant, toughened glass diffuser, IP65/66 protection and impact resistant of IK7 prewired with all accessories and connection up with 3 core flexible copper conductor cable 4/20 mm size, 1.5m long and testing on installation all as specified and directed. Make Havells Cat No ENDURAPEARLSL25WLED757SASYTOPCMP or equivelent of Bajaj/phillips/CG

S&F in replacement security light bracket made out of 25 mm bore GI Light grade 1.00 M long to required shape as in bracket for steet light fittings fixed with two pair of MS flate iron clamp of size 50mm X 6 mm thickness of required shape with nuts, bolts and washers suitable for steel tubular pole including painting of mild steel flate iron surface with two coates of synthetic enamel paint over a coat of red oxide primer complete including taking down unserviceable one all as specified and directed.

M & L for Sub main wiring with two runs of 6 sqmm (Nominal area) single core FRLS cable PVC insulated, multistranded, unsheathed, copper conductor cables 1100 Volts grade drawn through grey colour PVC conduits, medium grade, of suitable size, fixed to wall/ceiling etc with all accessories, fittings, fixures including 6 sqmm (nominal area) single core, PVC insulated, multistranded, unsheathed, FRLS copper conductor as earth wire and duly connected to common earth point including PVC conduits/casing-caping of suitable size complete all as specified and as directed by Engineer-in-charge. (Note : PVC Conduits, two run wiring cables and one run of earth wire will be measured as one length.)

Supply and fix in replacement Sheet metal enclosure (ISI marked) distribution board TPN, 415 volts, 4 way horizontal type double door type, 200 Amps rated neutral copper bus bar for housing MCB and fixed and tested on completion complete all as specified.

Supply and fix Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 8 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix Sheet metal enclosure (ISI marked) distribution board for 240 volts, SPN 4 way horizontal type, double door, single pole and neutral with 200 Amps rated neutral copper bus bar for housing MCB and fixed flush in wall surface, and tested on completion complete all as directed.

Supply and fix MCB Tripple pole & neutral 63 Amps 240 volts, C series,10 kA rupturing capacity providing in DB complete all as specified.

Supply and fix MCB single pole & neutral 40 Amps 240 volts, C series,10 kA rupturing capacity

Supply and fix MCB single pole 6 to 32 Amps 240 volts, C series, 10 kA rupturing capacity

Taking down ceiling fan of any size, any make sealing cable end, dismantling blades and painting of ceiling fan complete at site with synthetic enamel paint by spraying incl (fittings with filler) one coat after cleaning all dust etc incl refixing at site, connecting up by providing of twin core cable of suitable size for ceiling rose to connector connecting of earth wire incl replacement of fan capacitor 2.5/3.15 MFD,canopy, bearing/bush, rubber bushes minor nuts bolts screws washers greassing in fan bearing & refix same complete all as directed

Excavation in trenches n.exc 1.5 m wide and n.exc 1.5 m in depth for foundation, etc area not exceeding 10 Sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated material to a distance not exc. 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed.

M & L for Sand cushioning and covering with clean dry sand in trenches for protection of under ground cables (below, above and around the cable laid in trenches) complete all as specified and directed. (Note: Thickness after punning down shall be measured for payment)

Supply and laying well burnt bricks, locally available best quality bricks laid breath wise across the length of cable in trenches for protection of UG cables complete all as specified and directed.

S&F in replacement mild steel galvanized pipe light grade for protection & passing of LT cable fixed to poles/walls/laid under floor/roads complete including fittings/clamps as required at site all as specified for size of 40mm bore dia.

Supply, laying, jointing, testing and commissioning cross-linked polyethylene (XLPE) insulated, GI strips armoured cable for working voltage 1100 volts, 2 core, nominal cross sectional area of main conductor 10 Sqmm, stranded aluminium conductor, ISI marked as per IS-7098 (Part-I) 1988 including cable glands, lugs etc to suit the cable size and to be laid in trenches, culverts, under floors, through GI Pipe complete all as specified and as directed.

M&L for Earthing complete with galvanised steel earth plate electrode 60cm x 60cm x 6.0mm thick buried directly in ground (earth pit depth not less than 2.25m deep below the ground level) with top edge of earth plate at a depth not less than 1.5m below ground level connected to earth using GI earth wire of 6mm dia by means of of nuts, bolts and washer and check nuts of GI or steel as shown in electrical plate No.3 of MES SSR-2009 (Part-I) and connected to earth test point all as specified or indicated including testing on completion with and including 15mm bore light grade GI protection pipe 7.5 metre long for earth including PCC (1:2:4) pit with RCC (1:2:4) type B-1 cover, 40mm thick reinforced with 6mm dia MS bars @ 100mm both ways with lifting hooks made out of 6mm dia MS bars, watering arrangement with 20mm dia light grade pipe, funnel, wire mesh, common salt chorcoal, necessary excavation and earth work in any type of soil complete all as specified.

Srisrinivasaenterprises

Harish Constructions

R. P. Suppliers and Construction Co.

HRML CONSTRUCTIONS

SHREE BANASHANKARI ASSOCIATES

PRACHANIVA CONSTRUCTIONS

PAVAN TECHNO CONSTRUCTIONS