Construction of Conference hall at Hotel Palace Chail Distt. Solan (H.P).

Amount

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soils as directed, within all leads and lifts as per the direction of Engineer-In-Charge including carriage of materials within all leads and lifts. Ordinary rock.

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth leads and lifts upto 1.5 m All kinds of soil as directed by Engineer-in-charge including carriage of materials within all leads and lifts.

Filling in plinth with sand under floor including watering, ramming, consolidating and dressing complete as per the direction of Engineer-In-Charge including carriage of materials within all leads and lifts.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm.so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden batterns and ballies, height of the propping and centreing below supporting floor to ceiling not eexceeding 4mtrs.and removal of the same for insitu-reinforced concrete & plain concrete as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts Foundations, footings, bases of columns and mass concrete.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm.so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden batterns and ballies, height of the propping and centreing below supporting floor to ceiling not eexceeding 4mtrs.and removal of the same for insitu-reinforced concrete & plain concrete as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts Flat Surfaces such as soffit of suspended floor , roofs landings and the like floor etc. up to 200 mm in thickness.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm.so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden batterns and ballies, height of the propping and centreing below supporting floor to ceiling not eexceeding 4mtrs.and removal of the same for insitu-reinforced concrete & plain concrete as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts Columns / pillars, posts and struts square, rectangular or polygonal in plan

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm.so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden batterns and ballies, height of the propping and centreing below supporting floor to ceiling not eexceeding 4mtrs.and removal of the same for insitu-reinforced concrete & plain concrete as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts Beams, cantilevers, gurders / lintels sides and soffits of beams beam hounchings cantilivers, bressumers and lintels not exceeding 1.00 m in depth in all height in floor.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm.so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden batterns and ballies, height of the propping and centreing below supporting floor to ceiling not eexceeding 4mtrs.and removal of the same for insitu-reinforced concrete & plain concrete as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts Stair cases with sloping or stepped soffits excluding landing.

Providing form work with steel plates 3.15mm thick welded with angle iron in frame 30x30x5mm.so as to give a fair finish including centring, shuttering, strutting and propping etc. with wooden batterns and ballies, height of the propping and centreing below supporting floor to ceiling not eexceeding 4mtrs.and removal of the same for insitu-reinforced concrete & plain concrete as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts Edges of slabs and breaks in floors and walls

Providing and laying cement concrete 1:3:6 (1 cement:3 sand:6 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in Foundation and plinth as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts

Providing and laying cement concrete 1:4:8 (1 cement:4 sand: 8 graded stone aggregate 40mm nominal size) and curing complete excluding cost of form work in: Foundation and plinth as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level 1:1.5:3 (1 cement : 1.5 coarse sand): 3 graded stone aggregate 20 mm nominal size) as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand) : 3 graded stone aggregate 20 mm nominal size) as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more. as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts.

Brick work using coomon burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1:4 (1 cement : 4 coarse sand) as per the direction of Engineer-In-Charge including carriage of material upto all leads and lifts.

Half brick masonry in common burnt clay building bricks 2nd class in superstructure in cement mortar 1:4 (1cement:4sand) as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and laying 20 cm. thick composit stone masonry with hard stone as approved by the Engineer in Charge facing of chisel dressed stones one line dressed in superstructure above all heights cement mortar 1:6(1 cement :6 sand) and concrete backing with cement concrete 1:3:6 (1 cement: 3 sand: 6 graded stone aggregate 20 mm. nominal size) on inner face of walls including centring, shuttering and propping complete up to all heights finally removal of surface dropping and sand papered / wire brushed to remove all cement and points dropping on stone and finally given remmers treatment with chemical known as PUR Aqua Top 1 K as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. Super-structure above plinth level upto floor two level (Second Class Bricks).

Stone soling properly hand packed filling interstices with kharanja stone and consolidating to the required gradient and camber and rolling of binding materials moorum or earth etc. as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing wood work Second class teak wood in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately) as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in position with necessary stainless steel screws etc Kiln seasoned and chemically treated hollock wood as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 35 mm thick 2nd class Teak wood shutters panelled or panelled and glazed shutters for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Supplying and fixing 5.5 m thick glass panes with putty and nails including removal of broken glass panes wherever necessary as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. Saint Gobian / Modi Guard or equivalent make as approved by Engineer-In-Charge.

Providing and fixing toughened glass door and fixed glazing with SS patch and necessary hardware with hydrolic floor hinges fittings of approved make. Including Complete as per drawings.Fixed glass ( toughened) 12 mm thick as per direction of the Engineer-In-Charge including carriage of material upto all leads, lifts and heights. Saint Gobian / Modi Guard or equivalent make as approved by Engineer-In-Charge.

Providing and fixing Second class teak wood wire gauge shutters using galvanized M.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 12mm thick flat pressed 3 layer medium density particle board or graded particle board (Grade I) IS: 3087 marked, in ceiling with necessary nails etc. complete (frame work to be paid separately)as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing cup board by using 19 mm water proofing board of approved manufacture for shutters, vertical and horizontal partitions (teak board) etc. and fixing 6 mm thick water proof ply backing, painting/polishing, Ist class deodar wood beading, moulding, brass handles, cachers M.S. piano hinges & Godrej lock etc. complete as per Architectural/sketch drawings (attached) and as per the direction of the Engineer-in-Charge including carriage of material upto all leads, lifts and heights. (Greenply/Kit ply or equivalent). only front length and height to be measured.

Providing and fixing 2nd class teak wood wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 2nd class teak wood plain square edged cover fillets (beading) 50mmx12mm section, with wood screws in ceiling and lining including mitring at junctionas per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. 1st class deodar wood.

Providing and fixing 40x3 mm flat iron hold fast 40 Cm. long including fixing to frame with 10 mm dia bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 (1cement:3sand:6graded stone aggregate of 20 mm nominal size as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing bright finished brass 450mm long ornamental handle for main door of approved make and design with screws etc. complete as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 125mm bright finished brass handles of approved make (heavy duty) with screws etc. complete as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 100mm bright finished brass handles of approved make (heavy duty) with screws etc. complete as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 300x10 mm bright finished brass tower bolts (barrel type) of approved make (heavy duty) with necessary screws etc. completeas per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 200x10 mm bright finished brass tower bolts (barrel type) of approved make (heavy duty) with necessary screws etc. completeas per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 150x10 mm bright finished brass tower bolts (barrel type) of approved make (heavy duty) with necessary screws etc. complete as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing bright finished brass casement stays (straight peg type) of approved make (heavy duty) with necessary screws etc. complete 200 mm weighing not less than 240 gms as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 100 mm bright finished Brass floor door stopper with rubber cushion of approved make (heavy duty) screws etc. to suit shutter thickness complete and as per direction of Engineer-In-charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 250x16 mm bright finished brass sliding door bolts of approved make (heavy duty) with nuts and screws etc. complete as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality with necessary screws etc. complete as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing double action hydraulic floor spring of approved brand and manufacture (conforming to IS 6315) for aluminium door including cost of cutting floor as required embedding in floors and cover plates etc. complete as per the direction of Engineer-In-Charge I/c making good the floors including carriage of material upto all leads, lifts and heights.

Providing and fixing .150mm oxidized M.S. double acting spring hinges of approved make (heavy duty) with necessary screws as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing of approved design P.O. P. Celing decorative type as per the Architect Design/ Drawing of required thickness including GI Channel Main/ Cross with necessary screws complete in all respect ISI mark of approved quality as per directions of Engineer-In-charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 12mm thick readymade ornamental imported pine wood wooden plank ceiling with tongued and grooved jointing and wood screws (frame work and cover fillets to be measured and paid separately) as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 12 mm thick plain lining with tongued and groved jointing and screws (frame work and cover fillet to me measured and to be paid sepretely) with 1st class Indian teak wood as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 4mm thick water proof Kit Ply of approved quality ISI mark and approved shade and colour in wall linning including mitring at junctions, butt joiting and nails complete (frame work for base to be measure and paid for seperetly) as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. Merino/Green/Kit ply make

Supplying and fixing of class 33 Pre-laminated wooden floor HDF 12mm thick Density min 850 kg/m3 of class décor laminate min of 0.4 mm of overlay of melamine based paper with abrasion resistance cycle _>6000, impact Resistance IC in IC3 for 33th class, Scratch Residence EN438>3.5: satin resistance Class -5 thickness swelling _< 18% height difference max _>0.15mm with edge tolerance to 0.5-1.0 mm /mtr with underlay armor as desired 0.8-1.0 mm thick, surface soundness >1.25 N/mm of Elegance/Green panel or equivelent as per the direction of Engineer-In-Charge including carriage of materials within all leads, lifts and heights.

Providing and laying 600x600mm vitrified floor tiles in flooring (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Nitco/Kajaria/Rak or equivelent make as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. (Basic rate not less than Rs. 50/-)

Providing and laying Duro stone vetrified tiles (300x300mmx10mm) in grey/coloured or of approved shade in flooring, treads of steps and landing laid on a bed of 12mm thick cement mortar 1:3 (1 cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete. Nitco/Kajaria/ Rak or equivelent make as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. (Basic rate not less than Rs. 45/-)

20 to 25 mm thick Kota stone slab flooring over 20 (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and laying Coloured glazed (600x300mm) in required shade in skirting risers of steps and dados on 12mm thick cement mortar 1:3 (1cement : 3 sand) laid over and jointed with neat cement slurry finished with flush pointing in white cement mixed with pigment of required shade to match the shade of tiles complete Nitco/Kajaria/Rak or equivalent make as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. (Basic rate not less than Rs. 50/-)

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge including carriage of material upto all leads, lifts and heights.Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing and fixing 0.62 mm thick prepainted steel sheet (Tata Duroshine or equivalent make approved by Engineer-In-Charge) in roofing with hot dipped metallic zinc / aluminium-zinc alloy coated sheet with top coat of regular modified polyster (RNP) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 mocrons over 5 microns primer coating including fixing with self driven steel screws / prepainted iron J or L hooks or seam bolts with prepainted limpet and rubber washers complete with all accesoriees as required as per the detailed drawings and direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing ridges or hips 60 cm overall with 0.62 mm thick prepainted steel sheets in roofing withhot dipped metallic zinc / aluminium-zinc alloy coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, or seam bolts /driled screw & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing valleys 60 cm overall with 0.62 mm thick prepainted steel sheets in roofing withhot dipped metallic zinc / aluminium-zinc alloy coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating i/c fixing with prepainted iron J or L hooks, or seam bolts /driled screw & prepainted G.I. limpet and bitumen washers complete with all accessories as required as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing 15 cm. wide 45 cm. overall semicircular plain G.I. sheet gutter with iron brackets 40x3mm size bolts and nuts and washers etc. including making necessary conections with rain water pipe complete as per design.0.80 mm thick as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing flashing 38 cm overall with 0.60 mm thick prepainted sheet in roofing with hot dipped metalic zinc coated sheet in roofing with hot dipped metalic zinc coated sheet with top coat of regular modified polyster organic coating of 20 microns over 5 microns primer coating + back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6 mm dia meter & prepainted G.I. limpet & bitumen washer completed with all accessories as required as per the direction of Engineer-in-Charge including carriage of materials in all lead, lift and height (Tata/Century wells make).

Providing and fixing rolled cold M.S. BP Sheet 1.66mm to 2mm thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) as per the direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing on wall faces PVC (D- plast) 110mm dia for rain water pipes of working pressure not less than 4.5 Kg/ Sqmtr. including filling the joints with approved adhesive complete including carriage of material upto all leads, lifts and heights. Supreme/D-plast/Finolex make.

Providing and fixing on wall faces PVC (D-plast) accessories for rain water pipes including filling the joints with approved adhesive complete including carriage of material upto all leads, lifts and heights.. a) 100 mm dia plain bend Supreme/D-plast/Finolex make.

Providing and fixing PVC hold bat clamp including steel bolt to SCI pipes embedded in and including cement concrete block 100 mm x 100 mm x 100 mm of 1:2:4 (1cement: 2sand: 4 graded stone aggregate)including carriage of material upto all leads, lifts and heights. 110 mm nominal dia Supreme/D-plast/Finolex make.

Steel work welded of approved make in built up sections, / trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of material upto all leads and lifts and as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. In trusses and trussed purling in buildings.

Steel work welded of approved make in built up sections, / trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of red lead paint including carriage of material upto all leads and lifts and as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. In gratings framed guard bars,ladders,railling,brackets and similar works.

Providing and fixing P.O.P. punning (raised Dana) on walls wherever required, in sakarni or shriram masala with 12mm average thickness on vertical / horizontal surfaces of walls wherever required in plumb & line level to the entire satisfaction of the Architect. as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. Make - Adhar Shree, Sakarni, Shriram or J.B. Hisar

:Supply & fixing of ASP acoustic panels in non-woven polyester fibre acoustics panels made from Recycled fibre from waste PET bottles. It should have a density open cell construction whichresult in high sound absorption and thermal insulation.Thickness of 10mm with Density of 2000gm/sqm and high acoustic performance of up to 0.9NRC. It should be Formaldehyde free with high resistance to humidity & moisture.It should be light weight, flexible, highly versatile and should be impact resistance

Supplying and fixing of designer wall paper of approved make as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Applying Birla white wall care putty over plaster surface after thoroughly brushing the surface free from mortar foreign matters sand papered smooth to give final matter finish to the surface completeas per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Applying priming coat on new concrete/masonry/ asbestos cement/ plastered surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matters and sand papering as required with ready mix primer as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

6mm thick Cement plaster to ceiling including sides and bottom of beams, soffits of stairs, ramps etc. with cement mortar 1:3 (1cement : 3 fine Sand) including curing and carriage, leads of all kinds of materials and scaffoldings etc. complete as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

20mm Cement plaster in two coats,backing coat 15mm and finishing coat 5mm thick on rough side of brick/stone masonry walls for interior plastering upto floor two level including arrises, internal rounded angles,chamfers and/or rounded angles not exceeding 80mm in girth and finished even and smooth as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Wall Painting ( two coats) with plastic emulsion paint of approved brand and manufacture on decorated wall surface to give an even shade including thoroughly brushing the surface clean of all dirt grease, loose pieces of scale and sand papered smooth including applying of putty a required for making the surface as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Finishing wall with weather proof exterior grade emulsion of approved design (Apexultima) or its equarlied on undecorated wall surfaces (two coats) to give an even shade and final finish after throughly cleaning the surface to remove all dirt, dust and other foreign matter etc including sand paper smooth completeas per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing plinth protection 50mm thick in cement concrete 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size) as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Constructing course rubble hammer dressed “U” shape open surface drain with side wall 15x22 cm in cement mortar 1:6 (1cement:6sand) and inside plastering with cement plaster 1:3 (1cement:3sand) including earth work and laying 10 cm cement concrete in 1:5:10 (1cement:5sand:10 graded stone aggregate) of 40 mm nominal size and 7.5 cm cement concrete 1:2:4 (1cement :2sand:3 graded stone aggregate of 20 mm nominal size) and finished with a floating coat of neat cement complete as per standard design as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights.

Providing and fixing vitreous wash down Cera Make cat no S1021109 of equivalent series of Jaquar/Hindware make white colour studio set along with C.P. JET ,SEAT COVER, CISTERN and twin flushing valves etc. complete in all respect, water closet ( European Type - WC pan) with integral 'p' or 's' trap including jointing the trap with soil pipe in cement mortar 1:1 ( one cement, one sand) (with cistern, seat cover and flush fitting) Star White as per direction of Engineer-In-Charge including carriage of material upto all leads, lifts and heights. ( snow white)

Providing and fixing wash basin with built in counter Cera Cat. No. S2030104,865x500mm of equivalent series of Jaquar/Hindware make including carriage of materials up to all leads and lifts and as per direction of Engineer in charge.

Providing and fixing wash basin with pedastal Cera Cat. No. S2040103,550x400mm of equivalent series of Jaquar/Hindware make including carriage of materials up to all leads and lifts and as per direction of Engineer in charge.

Providing and fixing 15 mm nominal size Basin Mixer Cera Cat. No.2013461 of equivalent series of Jaquar/Hindware make with 450mm braided connection pipe including carriage of material upto all leads and lifts and as per direction of Engineer incharge. .

Providing and fixing steel sink of Cera Make cat no. B4621101 of equivalent series of Jaquar/Hindware make of approved design size: a) 610mmx455mmx225mm including carriage of materials up to all leads and lifts and as per direction of Engineer-in-charge.(Darby lite 24" x 18")

Providing and fixing CP Sink Mixer Cera make Cat. No.F2013501 of equivalent series of Jaquar/Hindware make with 150mm long swivel spout, connecting legs and wall flange including carriage of material up to all leads and lifts and as per direction of Engineer-in-Charge.

Providing and fixing Urinal with senser size(mm) 320 X 300 X 525mm Cera make Cat No. S4010102 of equivalent series of Jaquar/Hindware make including carriage of material up to all leads and lifts and as per direction of Engineer incharge.

Providing and fixing 100mm pipes P or S Trap for water closet Sand Cast iron including carriage of material up to all leads and lifts and as per direction of Engineer incharge.

Providing and fixing bottel trap with fully casted body (with integral partition ) 32mm with 190 and 125mm long connecting pipes and wall flang Cera make Cat. No.F8060101 150mm of equivalent series of Jaquar/Hindware make including carriage of material upto all leads and lifts and as per the direction of Engineer -in-charge

Providing and fixing CP brass liquid soap dispenser Cera make Cat No. F5002111 of equivalent series of Jaquar/Hindware make with CP brass brackets fixed to wooden cleats with CP brass screws including carriage of material up to all leads and lifts and as per direction of Engineer incharge.

Providing and fixing CP brass waste for wash basin or sink Cera make Cat No F8050351 of equivalent series of Jaquar/Hindware make 32 mm dia with half thread 32mm including carriage of material upto all leads and lifts and as per direction of Engineer incharge

Providing and fixing designer superior glass mouted over 4mm water proof ply with decorative moulding on wooden plug with CP brass screw including carriage of materials within all leads and lifts as per direction of Engineer-In-Charge.

Providing and fixing CP brass soap dish Cera make cat no F5002106 of equivalent series of Jaquar/Hindware make with CP brass brackets fixed to wooden cleats with CP brass screws including carriage of material to all leads and lifts and as per direction of Engineer-in-charge.

Providing & Fixing in position coab and hat robe hooks fixed into wall with c.p. brass screws and rawl plugs etc. Cera make CAT No. F5002108 of equivalent series of Jaquar/Hindware make complete including cutting and making good the walls etc.including carriage of material up to all leads and lifts and as per direction of Engineer incharge.

Providing and fixing C.P. Paper Holder Cera make Cat No. F5007109 of equivalent series of Jaquar/Hindware make including carriage of material up to all leads and lifts and as per direction of Engineer incharge.

Providing and fixing C.P. Grab bar Cera Make Cat No. B2210105 of equivalent series of Jaquar/Hindware make 350mm long including carriage of material upto all leads and lifts.

Providing and fixing CP brass bib tap with capstan head 15mm dia (Cera make Cat No. F1014152) of equivalent series of Jaquar/Hindware make with wall flange and areator including carriage of material to all leads and lifts and as per direction of Engineer incharge. ( Long nose)

Providing and fixing P.V.C. waste pipe of approved make (heavy duty) for wash basin and sink including carriage of material upto all leads and lifts and as per direction of Engineer incharge

Providing and fixing 15mm nominal size CP brass angle valve/ Stop Cock Cera Make Cat No. F2013201 of equivalent series of Jaquar/Hindware make with flange including carriage of material to all leads and lifts and as per direction of Engineer incharge.

Providing & Fixing C.P. Towel Ring Cera Make Cat No.F5002105 of equivalent series of Jaquar/Hindware make including carriage of material upto all leads and lifts and as per direction of Engineer incharge

Providing and fixing 100mm dia C.P. Grating including carriage Chilly make of material up to all leads and lifts and as per direction of Engineer incharge.

Providing and fixing PVC connections pipe Cat No. F8070402 of equivalent series of Jaquar/Hindware make with brass unions 45cm length 15 mm nominal bore including carriage of material in all leads and lifts

Providing and fixing M.I. Union of approved make (heavy duty) including carriage of material up to all leads and lifts and as per direction of Engineer incharge. i) 15 mm dia

Providing and fixing M.I. Union of approved make (heavy duty) including carriage of material up to all leads and lifts and as per direction of Engineer incharge ii) 20 mm dia

Providing and fixing brass full way valve with wheel including carriage of material up to all leads and lifts and as per direction of Engineer incharge a) With water storage 15mm size. Zoloto/Leader or equivalent make

Constructing manhole with RCC top slab in 1:2:4 (1 cement : 2 sand : 4 graded stone aggregate ) 20mm nominal size foundation concrete 1:4:8 (1 cement : 4 sand : 8 graded stone aggregate 40mm nominal size) inside plastering 15mm thick with cement mortar 1:3 ( 1 cement : 3 sand) finished with afloating coat of neat cement and making channels in cement concrete 1:2:4 ( 1 cement : 2 sand : 4 graded stone aggregate 20mm nominal size) finished smooth complete including curing and testingincluding carriage of material in all leads and lifts. a) Inside size 800x800x500mm deep including C.I. cover with frame (Light duty single seal : Pattern) 455mmx 610mm integral dimensions total weight of cover and frame to be not less than 38 kgs (weight of cover 23kg and weight of frame 15 kg with 200mm thick walls of brick masonry using common burnt clay building bricks in cement mortar 1:3 ( 1 cement : 3 sand)including carriage of material in all leads and lifts.

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:6 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:4:8 (1 cement : 4 fine sand : 8 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:6 (1 cement : 6 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design including carriage of material up to all leads and lifts and as per direction of Engineer incharge.

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Medium Grade) tube fitting and clamps as per IS code including making good the wall ceiling and floor including carriage of material in all leads and lifts. (including trenches) a) 15mm nominal size. Tata/Jindal or equivalent make

Providing and fixing to wall ceiling and floor galvanized mild steel tubes (Medium Grade) tube fitting and clamps as per IS code including making good the wall ceiling and floor including carriage of material in all leads and lifts. (including trenches) b) 20mm nominal size Tata/Jindal or equivalent make

Providing and fixing 75 mm nominal inner dia Pipes Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. Supreme/Astral/Finolex make.

Providing and fixing 110 mm nominal inner dia Pipes Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. Supreme/Astral/Finolex make.

Providing and fixing PVC floor trap of self cleaning design with C.P screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors 75 mm niminal diameter ( 100mm)

Supplying in PVC cover with frame for man holes for frame of internal dimension 600x600mm rectanguler CI cover (light duty single sear pattern -I)the weight of vocer to be not less than 23 Kg including carriage of material upto all leads and lifts and as per direction of Engineer incharge

Providing and laying semicircular SW pipe 150mm dia over a bed of CC 1:2:4 including jointing the SW pipe with each other in drain within RR Masonry /cc edge wall including carriage of material upto all leads and lifts and as per direction of engineer incharge

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank. Jai Bharat/Victus/Sintex or equivalent make

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required including carriage of materials within all leads, lifts and heights. The Wire should be Havell's/KEI/Finolix make, Switch, Metal Box & modular plate shall be Havell's/Anchor Panasonic/Legrand/L&T or equivalent make and PVC pipe should be Diplast/Polyplast/Setia make as approved by the Engineer-In-Charge. Group A

Wiring for light point / fan point / exhaust fan / call bell point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required including carriage of materials within all leads, lifts and heights. The Wire should be Havell's/KEI/Finolix make, Switch, Metal Box & modular plate shall be Havell's/Anchor Panasonic/Legrand/L&T or equivalent make and PVC pipe should be Diplast/Polyplast/Setia make as approved by the Engineer-In-Charge. Group A b) Group C

Wiring for twin control light point with 1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit with 2-way, 5/6 amps. modular switch, modular plates, suitable G.I. box and earthing the light point with 1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable as required. The Wire should be Havell's/KEI/Finolix make, Switch, Metal Box & modular plate shall be Havell's/Anchor Panasonic/Legrand/L&T make and PVC pipe should be Diplast/Polyplast/Setia make as approved by the Engineer-In-Charge. including carriage of materioal in all leads & lifts. a) Group C

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 5 pin 5/6 amps modular socket outlet and 5/6 amps, modular switch, connections etc. as required including carriage of materials within all leads, lifts and heights. Make:- Havell's/Anchor Panasonic/Legrand/L&T or equivalent make as approved by the Engineer-In-Charge.

Supplying and fixing G.I. Modular box of (140mmx78mmx50mm) size with modular plate and cover in recess including providing and fixing 6 pin 15/16 amps modular socket outlet and 15/16 amps, modular switch, connections etc. as required including carriage of materials within all leads, lifts and heights.Make:- Havell's/Anchor Panasonic/Legrand/L&T or equivalent make as approved by the Engineer-In-Charge.

Supplying & fixing of G.I. modular boxes of following sizes along with modular base and cover plate for modular switches in recess including providing and fixing RJ 45 UTP information outlet modular as required including carriage of materioal in all leads & lifts. Make:- Havell's/Anchor Panasonic/Legrand/L&T or equivalent make as approved by the Engineer-In-Charge.

Supplying and fixing of following sizes of PVC conduit along with the accessories in surface / recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required:- a) 25 mm. dia Pipe D-plast/Polyplast or equvalent make.

Wiring for light plug with 2x1.5 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.1.5 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required including carriage of materials within all leads, lifts and heights. Make:-Havell's/KEI/Finolix or equivalent make as approved by the Engineer-In-Charge..

Wiring for power plug with 2x4 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.4 Sq.mm. HRFRLS/PVC insulated single core copper conductor cable for earthing as required including carriage of materials within all leads, lifts and heights. Make:-Havell's/KEI/Finolix or equivalent make as approved by the Engineer-In-Charge.

Supplying and drawing following size of PVC insulated, heat resistant, flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in existing surface / recessed, Steel/PVC conduit as required including carriage of materials within all leads, lifts and heights. Make:-Havell's/KEI/Finolix 4x1.5 Sq. mm. or equivalent make as approved by the Engineer-In-Charge.

Wiring for circuit/sub-main with following size PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.HRFRLS/PVC insulated single core copper conductor cable of same size for earthing as required including carriage of materials within all leads, lifts and heights. Make:-Havell's/KEI/Finolix 2 x 6.0 Sq. mm. or equivalent make as approved by the Engineer-In-Charge.

Wiring for circuit / sub-main with 2x10 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 1 No.10 Sq.mm. (2x10+1x10) HRFRLS/PVC insulated single core copper conductor cable for earthing as required including carriage of materioal in all leads & lifts.. Make:-Havell's/KEI/Finolix or equivalent make as approved by the Engineer-In-Charge.

Wiring for circuit / sub-main with 4x10 Sq. mm. PVC insulated heat resistant flame retardant (HRFR) and low smoke single core (flexible) copper conductor cable in surface/recessed PVC conduit along with 2 No.10 Sq.mm. (4x10+2x10) HRFRLS/PVC insulated single core copper conductor cable for earthing as required Make:-Havell's/KEI/Finolix or equivalent make as approved by the Engineer-In-Charge. including carriage of materioal in all leads & lifts.

Supplying and fixing Ding-Dong / Electronic musical bell, suitable for D.C./A.C. single phase,230 volts complete as required including carriage of materials within all leads, lifts and heights. Make:- Anchor/Havell's/Greatwhite/Cona or equivalent make as approved by the Engineer-In-Charge.

Supplying and drawing following pair of Fire Retardant, PVC insulated 0.5 sq.mm. (FR-Flexible) copper conductor, flat, unarmoured, telephone cable in existing surface / recessed, steel / PVC conduit as required including carriage of materials within all leads, lifts and heights. Make:-Havell's/KEI/Finolix 2 Pair or equivalent make as approved by the Engineer-In-Charge.

Supplying and drawing co-axial TV cable,RG-6 grade,0.7mm (75 Ohms) copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed, steel / PVC conduit as required including carriage of materials within all leads, lifts and heights. Make:-Havell's/KEI/Finolix or equivalent make as approved by the Engineer-In-Charge.

Providing and installation of exhaust fan of following sizes in the existing opening, including making the hole to suit the size of the above fan, making good the damages, connections, testing and commissioning etc. as required. Exhaust Fan, Heavy duty, 300 mm sweep Make:- Havell's/ Usha/ Crompton or equivalent make as approved by the Engineer-in-charge

Providing and installation of stationary storage type Electric water heater (Geyser) of various sizes by means of Expansion-bolts with nuts and washers, including embedding of expansion-bolts in the wall, providing and fixing of Nonreturn valve, Dead weight safety valve, 2 No C.P. connection rods 18" long, making good the damages, electrical connections, safety valve connections, testing and commissioning etc. as required including carriage of materials within all leads, lifts and heights. a) (Geyser shall be horizontal type) 35 Litre capacity water heater (Cat-A) Make:-Spherehot/ Jaquar/Havell's

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required including carriage of materials within all leads, lifts and heights. Make:-Havell's/L&T/Legrand a) Telephone socket outlet, Modular or equivalent make as approved by the Engineer-In-Charge.

Supplying and fixing following rating Modular switch /socket in the existing switch box / cover plate including connections etc. as required including carriage of materials within all leads, lifts and heights. Make:-Havell's/L&T/Legrand b) TV. Socket outlet, modular

Providing, laying and fixing of one No. aluminium conductor, XLPE insulated and PVC sheathed, armoured/XLPE power cable, working voltage 1100 volts grade on surface etc. of the required size including carriage of materials within all leads, lifts and heights. Make:- Havell's/KEI/Finolex or equivalent make as approved by the Engineer-In-Charge. a) Armoured cable 6 sq. mm (twin core)

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required including carriage of materials within all leads, lifts and heights.Make:-Legrand/Havell's/L&T or equvalent make as approved by the Engineer-in-charge a) Double door-12 way

Supplying and fixing of following way, single pole and neutral sheet steel MCB distribution board, 240 volts, on surface / recess, complete with tinned copper bus- bar, wireset, neutral link, earth bar, din-bar, detachable gland plate, blanking plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required including carriage of materials within all leads, lifts and heights.Make:-Legrand/Havell's/L&T or equvalent make as approved by the Engineer-in-charge b) Double door-16 way

Supplying and fixing of following way triple pole and neutral, sheet steel MCB distribution board, 415 volts, on surface /recess, with provision for 4-pole MCB/Isolator/RCCB/RCBO as incomer and SP MCBs as outgoing, complete with tinned copper bus- bar, wire-set, neutral link, earth bar, din-bar, detachable gland plate, cable, identification labels interconnections, phosphatized and powder painted, including earthing etc. as required Make:-Legrand/Havell's/L&T or equvalent make as approved by the Engineer-in-charge. :- Double door-6 way (8+18),horizontal type

Supplying and fixing following rating, double pole (single phase & neutral) 240 volts, residual current circuit breaker (RCCB), having a sensitivity current up to 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc. as required including carriage of materials within all leads, lifts and heights. Make:-Legrand/Havell's/L&T or equvalent make as approved by the Engineer-in-charge. a) 63 Amps. Cat-A.

Supplying and erection of 6 amps. to 32 amps. rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required including carriage of materials within all leads, lifts and heights. Make:-Legrand/Havell's/L&T or equvalent make as approved by the Engineer-in-charge. a) Single pole Cat-A

Supplying and erection of 40/50/63 amps rating, 10 KA breaking capacity, 240 volts, 'C' curves, miniature circuit breaker of following poles in the existing MCB DB complete with connections etc. as required Triple pole & Neutral including carriage of materials within all leads, lifts and heights. Make:-Legrand/Havell's/L&T or equvalent make as approved by the Engineer-in-charge. a) Triple Pole CAT-A

Supplying and fixing 20 Amps, 240 volts, SPN industrial socket outlet, 2-pole & earth, metal enclosed plug top, sheet steel enclosure, suitable to accommodate a 20 Amp SPN-MCB/DP, on surface or in recess, with chained metal cover for the socket outlet, complete with connections, testing and commissioning etc. as required including carriage of materials within all leads, lifts and heights.Make:-Legrand/Havell's/L&T or equvalent make as approved by the Engineer-in-charge.

Supplying and fixing sheet metal bus-bar chamber suitable for 300 Amp. 415 volts capacity with 4 No. aluminium alloy or wrought aluminium strip bus-bars each of length 1200mm & cross-sectional area (51mmx6mm), enclosure made from 1.6 mm thick M.S. sheet having overall dimensions (1280mmx500mmx200mm) nominal with all accessories including connections, earthing the body etc. as required as approved by the Engineer-In-Charge.

Providing and fixing following rating and breaking capacity MCCB in the existing cubical panel board including drilling holes in the cubicle panel, making connections, etc. as required. 315/400 Amp as required as approved by the Engineer-In-Charge..-50KA

Supplying and fixing following rating, four pole (Three phase & neutral) 415 volts, 2-way centre off changeover switch in the existing MCB DB complete with connections, testing and commissioning etc. as required as required as approved by the Engineer-In-Charge.. 40 Amps.

Earthing with copper earth plate 600mmx600mmx3mm thick,including accessories and providing masonry enclouser with cover plate having locking arrangement and watering pipe etc.(but without charcoal or coke and salt) complete as required as required as approved by the Engineer-In-Charge..

Extra for using salt and charcoal for G.I. or copper plate earth electrode complete as required.

Supplying and erection of Galvanized Iron (G.I.) pipe pole 'A' quality of suitable length and dia., 4.47 mm thickness, including fixing up to a given depth below G/L. The hole of excavation about 30 cm dia. and given depth to be filled in up to 15 cm below G/L with 1:3:6 cement concrete and there above plinth with 1:2:4 cement concrete up to a height of 45 cm from G/L. The radial thickness of the plinth above G/L should not be less than 6.35 cm and sufficient to completely flush a 180 mmx100 mmx 45 mm deep, glass filled Nylan F.R. grade box for housing a 16 Amp. MCB, the outer surface of the plinth to be finished with 1:3 cement plaster 6 mm thick, the fuse-box shall have a water tight cover, including painting of pole with two coats of approved color, brand and manufacture of paint over a priming coat complete in all respects as required:- 4 Meter long having nominal bore dia.65 mm planting depth 80 cm with pit depth 95 cm.

Supplying and fixing of new generation,LED post Top, energy saving environment friendly,long life aesthetically designed in cast aluminium spigot housing with decorative opal polycarbonate diffuser and IP65 protection with high power LED's as light source 40 watts complete with all accessories including making connections,testing etc. as required Cat No. 111538 BGCL 40W LED WH Bajaj make or its equivalent as approved by the Engineer-in-charge.

Providing and fixing following type of surface mounting up down LED lighting fixture with extruded polycarbonate,environmental friendly energy efficient 6W LED 4000K complete with all accessories,connections,testing and commissioning etc. as required as required as approved by the Engineer-In-Charge.

Providing and fixing of recess mounting LED COB lighting fixture with extruded polycarbonate,environmental friendly energy efficient 9W LED 4000K with suitable capacity driver complete with all accessories,connections,testing and commissioning etc. as required as approved by the Engineer-In-Charge.

Providing and fixing of wall mounting LED picture lighting fixture with extruded polycarbonate,environmental friendly energy efficient 12W LED 4000K with suitable capacity built in driver complete with all accessories,connections,testing and commissioning etc. a as required as approved by the Engineer-In-Charge.

Supplying and fixing of surface type next generation energy efficient and high reliable IP66 wellglass luminare 40watts with cradel and eye bolt mounting. In built loop-in-loop ouit facility by metal gland ensures optimizatiopn in installation process complete with all accessories, making connections,testing etc. as required. Surface type LED light 40 Watts CAT NO. BIWDN40LWHPCSD Bajaj/Philips/Havell's or equivalent make.

Providing and fixing LED 9 lights Antique Brass Finish Gold mild steel Chandeller size 31x31x19.2 inches following LeArc LED lighting make with E-27 holders suitable for 40 watts E-27 lamp complete with all accessories,connections,testing and commissioning etc. as required or as approved by the Engineer-In-Charge.

SHASHANK KUMAR