SPECIAL REPAIR TO BLDG NO P-345 AND P-346 AT MIL STATION BHUSAWAL UNDER GE (SOUTH) AHILYANAGAR

Amount

Dismantling asbestos cement sheet (corrugated or semi corrugated etc) including ridges in large patches as in roof covering complete all as specified and as directed. Note:- Dismantling existing wind tie and refixing the same where required for taking down of sheets shall deemed to be included in the unit rate quoted .

S&F prepainted galvalume aluminium zinc coated galvanised iron based corrugated steel sheets, 0.5 mm thick of any colour, AZ150, having tensile strength 550 MPA as in roof covering or ridges with side lap and end laps, hips and straight flashing fixed with self taping screws (length & girth as fixed) complete all as specified and as directed. Note:- Colour & Pattern to be approved by Engineer-in-Charge.

S&F pre-painted galvalume aluminium zinc coated galvanised Iron based Plain steel sheets, 0.5mm thick of any colour, AZ 150 coating, with side lap and end lap having tensile strength 550 MPA as in ridges, hips, valley gutters, drip and straight flashing fixed with self taping screws (length & girth as fixed) complete all as specified and as directed. Note:- Colour & Pattern to be approved by Engineer-in-Charge.

S&F 1.25 mm thick Plain, black, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed)including necessary welded or soldered joints complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for all as specified and as directed.

S&F Steel work in Rolled sections section as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates. Fe 410 -W (Gde- E- 250) quality- A complete all as specified and as directed.

S&F mild steel work as in bands, straps, support for rain water pipes & valley gutters etc conforming to Fe 290 Gde-E-165 complete all as specified and as directed.

M&L for preparation of new steel surface of any description over 10cm in width or girth and applying two coats of synthetic enamel paint of any shade over a coat of red oxide primer complete all as specified and directed. Note : The rate quoted includes painting of members of trusses at any height as per site conditions.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed. Note : The rate quoted includes painting of members of trusses at any height as per site conditions.

S&F, in repair, 110mm bore PVC (SWR) single socketed in any length with rubber ring joints and fixed to walls all as specified and directed by Engineer-in-charge.

S&F in repair,110 mm bore (SWR) PVC bends any radius complete as directed by Engr-in-Charge.

M&L for brickwork with fly ash bricks (old size), straight or curved on plan, exc 6 m mean redius, built in cement mortar 1:6 with and including demolition of existing brick work built in cement or cement lime mortar of any description complete all as specified and as directed.

Taking down cement plaster incl racking out joints, hacking for key & scrubbing down with water etccomplete all as specified and as directed.

M&L for rendering 10 mm thick on fair faces of brick work or concrete suraces in cement mortar 1:6, finished even and smooth without using extra cement complete all as specified and as directed

M&L for rendering 15mm thick on fair faces of brick work or concrete surfaces (external) in cement mortar 1:4, finished even and fair complete all as specified and as directed

M&L for Preparation of newly plastered wall surfaces and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of cement base paint over and including alkali resistant primer complete all as specified and as directed.

Taking down chowkhats or frames with shutter (without taking out shutter from the frame), area exc 1.5 sqm but not exc 4 sqm each all complete all as specified and as directed.

S&F factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ ceosetory windows & other frames/ chowkhat of size 45 x 70 mm comprising of virgin PVC polymer of K value 58-60 (Suspension grade), Calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N(Face) & 1100 N (Edge), minimum compressive strength of 58 N/Sqmm, modules of elasticity 900 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/ moisture proof and fire retardantand fixed in position with mild steel hold fast/ lugs/SS dash fasteners of required dia and length complete as per specified and as directed. Note: (i) Minus 5mm tolerance in dimension i.e. depth and width of profile shall be acceptable for WPC solid door/window frames. Variation in profile dimensions on plus side shall be acceptable without any extra cost to the department.

S&F factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of 35 mm size comprising of virgin polymer of K value 58-60 (suspension grade), Calcium Carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (face) & 900 N (edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges 4 nos per leaf of required size with necessary full body threaded star headed counter sunk S.S screws, complete all as specified and as directed.

S&F 150mm size extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and as directed.

S&F 200mm size aluminium anodized barrel tower bolts of extruted section and fixed complete all as specified and as directed.

S&F 300mm long aluminium alloy anodised sliding door bolts with hasp, staple and fixing clip of sheet cast or extruded section and fixing bolt and sliding bolt of extruded section or cast- aluminium alloy complete all as specified and as directed.

M&L for preparation of old plastered or unplastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of old plastered or unplastered surfaces of wall and applying two coats of cement base paint complete all as specified and as directed.

S&F steel rolling shutters made out of 1.25mm thick laths, including top cover, anchoring rod, hasp and staple and one shop coat of primer,erected in position as directed gear operated type with bevel gear box and crank handle including taking down old shutters complete all as specified and as directed. Note : BOO shall be ordered to ascertain the weight of old shutters to be given on credit.

S&F Safety lever locks mild steel with 4 levers for rolling shutters complete all as specified and as directed.

S&F Ball bearing for rolling shutters complete all as specified and as directed.

Demolition of cement Concrete (Unreinforced) any description and in any position not otherwise specifically provided for complete all as specified and as directed.

M&L for Plain cement concrete 1:2:4, Type B-2, (using 40 mm graded corase aggregate) as in surface channels and drains including form work complete all as specified and directed

Taking down chowkhats or frames with shutter (without taking out shutter from the frame), area n.exc 1.5 sqm each complete all as specified and as directed.

S&F Steel ventilator with side hung shutter including hinges, steel peg stay, complete all as specified and as directed.

S&F 3mm thick plain sheet glass, ordinary quality and glazing with oil putty or wooden beading, size not exc 0.5 sqm in each pane complete all as specified and as directed.

Demolition of cement concrete in ground floors and pavings n. exc 15cm thick (below or above ground level) un-reinforced. complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8, type D2 (using 40mm graded stone aggregate) as in sub base of floor all as specified and as directed.

M&L for 75 mm thick Plain cement concrete type B-1 (1:2:4) (Using 20 mm graded aggregate) as in flooring, finished the surface even and smooth without using extra cement complete all as specified and as directed.

Taking down carefully copper/Aluminum point wiring (Light, Fan, Socket or power) complete fitting such as switches, ceiling, regulator, sockets etc removing materials to be store for keeping in safe custody for taking credit and making good disturbed surfaces of walls, floors etc and matching with existing surface complete all as specified and as directed.

M&L for point wiring complete on surface of wall (open) type with two runs of 1.5 sqmm for phase and neutral, single core, multistranded copper conductor cable of 1100 Volts grade,conforming to IS-694 1990, PVC insulated and unsheathed , FRLS cable drawn through and including PVC casing and caping (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmm copper conductor cable (multistranded) PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC folding boards/bakelite sheets for mounting switches, sockets, fan Regulators, accessories etc as specified and as directed for one light point or one fan point controlled by one, one way switch NOTES: (a) Proper colour coding shall be adopted for wiring (for phase-RED,YELLOW, BLUE for Earth-Green and Neutral-Black) (b) Wiring shall be done as per complaints received from user only on reqired basis it is not necessary to do whole wiring of any whole bldg. (c) All points shall be earthed up to fixtures i.e holders, tube lights, all lights, ceiling lights, bulkhead lights, bldg security lights etc.

All as per serial item No 39.00 here in before but for one 3 pin 6 Amp Socket outlet point on same board with other switches including earth wire as per description given above and connected to common earth and earth terminals.

All as per serial item No 39.00 here in before but for one 3 pin 6 Amp Socket outlet point on independent board including earth wire as per description given above and connected to common earth and earth terminals.

All as per serial item No 39.00 here in before but with 2.5 Sqmm cables for one 16A, 6-Pin (multipurpose) socket outlet point on independent board with & including 2.5 Sqmm FRLS (H) cable as earth wire complete all as specified and as directed.

S&F switch piano, flush button, 6 Amp, single pole, one way, 230 volts, white finish, all as specified & as directed.

S&F switch socket combination, flush type, 5 pin, 6 Amp, multipurpose, 230 volts, single pole, one way, suitable for 3 pin/2pin 5 Amp plug top white/ivory finish all as specified & as directed.

S&F switch socket combination, multipurpose, flush type, 2 in 1 type (6 pin ) 6/16 Amps, 230V, AC. all as specified & as directed.

S&F ceiling rose, surface PVC 50mm dia, 3 terminals including PVC mounting block white/ivory finish all as specified & as directed.

S&F lamp holder, angle/ batten type, PVC/Polycarbonate type with back plate, suitable for batten fittings all as specified & as directed.

S&F fan regulator, step type, electronic on existing phenolic laminated sheet, 5 step, socket type, 230 volts, 450 watts, suitable for ceiling fan 1200/1400mm sweep all as specified & as directed.

S&F in replacement decorative ultra slim batten square profile LED lighting fixture with extruded polycarbonate, environmental friendly, energy efficient of capacity 20 Watt , 6500 K with inbuilt driver complete fitting and all other accessories fitting arrangements including connecting up with two core flexible copper conductor cable of suitable size from ceiling rose complete all as specified and as directed. Make : Cat No. LHEXAWP7UN1W020 of Havells or equivalent of makes specified in PS

M & L for sub main wiring with 2 runs of 2.5 sqmm, single core, PVC insulated & unsheathed FRLS cable conforming to IS-694, 1100 volts with copper conductor, multi stranded drawn in and including suitable size heavy grade casing caping (ISI marked) with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 2.5 sqmm single core PVC insulated & unsheathed FRLS copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion including taking down old submain wiring and any type of conduit complete all as specified and as directed. NOTE: 1.Proper colour coding shall adopted for wiring (for phase-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) 2.Three runs of 2.5 sq.mm cable and one run of PVC casing & caping shall be measured as one unit.

S&F in repairs, MCB SP, AC 240 V, 6 to 32 Amps, 10 KA capacity, 'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in repairs, MCB SPN, AC 240 V, 6 to 32 Amps, 10 KA capacity, 'c' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in repairs, sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), single pole and neutral, 240 volts, 8 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming As per IEC 61439-3, suitable for flush mounting and surface mounting, with 200 Amps rated copper busbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed.

S&F in repairs, sheet metal enclosure (Factory made), double door shutter type for distribution board (when MCBs are to be used), Tripple pole and neutral, 415 volts, 4 way, protection class IP-42, suitable for fixing MCBs, Isolators etc, confirming As per IEC 61439-3, suitable for flush mounting and surface mounting, with 200 Amps rated copper busbar, with Neutral bar, Earthbar and cable alley for cable managment, fully shrouded, Neutral bars, prefittes masking sheet complete all as specified and as directed.

S&F in repairs ISOLATOR TPN, AC 415 V, 63 amps, 10 KA capacity ,'C' series, making connection with suitable size of copper lugs etc complete all as specified and as directed.

S&F in replacement 35 Watt building mounted LED security light fitting complete made up of pressure die cast housing with toughened glass and individual high power LEDs with secondary optics, IP66 protection and impact resistance of IK07 & 10KV external SPD, including GI bracket made out of GI pipe 40/50 mm bore, medium grade pipe 1.2m long bend to shape required fixed to pole / wall with 02 Nos MS clamps made out of flat iron 40x5 mm including nuts, bolts and washer, painting with two coats aluminium paint over a coat of primer, suitable for LED fitting complete all as specified and as directed. Make : Havells Cat No ENDURACITYLITEPLATPLUSSL35WLED757SASYBOPC or equivalent model of makes specified.

S&F in repairs LED Flood Light 120 watt 230V AC outdoor type with thermal management in multiple optics and energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium IP65 flood light with high power LEDs as light source with impact and corrosion resistant complete with driver and lamp complete all as specified and as directed. Make : Havells Cat No JETAADORNNXTFLS120WLED757SSYMTOTGV2 or equivalent model of makes specified.

M&L in repairs/replacement earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6.0 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia , by means of nut bolts, check nuts and washer of the GI . Earth wire connected upto main earth point/DBs alongwith 15mm dia GI pipe, medium grade, including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4) cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion.

Bhirud Electric Stores (BID ID -3505846)

CHAUDHARY AND ASSOCIATES (BID ID -3506308)

M/S H.N.ENTERPRISES (BID ID -3506344)