Construction of Science lab in Govt. Senior Secondary School at Kohlari Distt. Chamba Construction of Building portion WS and SI and Rain Water harvesting system

Amount

Excavation in foundation and trenches in all heights and depths and in all kinds of soil including saturated soils comprising of pick work, jumper work, pick jumper work, blasting work both in soft and hard rock, chiseling / wedging out of rock (Where blasting is prohibited) and their intermediate classification of soil setting out true to the required lines, grade, width, cutting and trimming of side slopes as shown in the drawing and if water is met within the excavation due to springs, seepage, rain and other causes it shall be removed by the suitable diversion pumping or bailing out and excavation shall be kept dry wherever so required by the contractor at his own cost as directed by the Engineer-in-charge and disposal of all surplus excavated soil in acquired width or at an approved dumping side including its stacking leveling dressing including all leads and lifts by head-load, mechanical transportation or by any other mode of transportation with all cost of labours, machineries and other incidentals to complete the work as per HPPWD specification. Any loss to the public and private property during the course of execution and disposal of unserviceable material shall be absolute responsibility of the contractor which shall have to be compensated by him in all cases. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Stone filling under floor/ behind retaining wall etcetera complete including all taxes and carriage of material, as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in foundation, footing, basis of columns etcetra and mass concrete including carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Columns, pillars, posts and struts square rectangular or polygonal in plan including carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Beams, cantilever, girders and lintels. Sides and soffits of beams, beam haunchings, cantilevers, bressumers and lintels upto all depth and in all heights from floor including , carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Flat surfaces such as soffits of suspended floors, roofs, landings and the like floor etcetra upto any thickness including carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling and removal of the same for insitu-reinforced concrete and plain concrete work in Stair cases with sloping or stepped soffits excluding landing including carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing form work with steel plates 3.15 mm (three point fifteen millimetre) thick welded with angle iron in frame 30 X 30 X 5 mm (thirty into thirty into five millimetre) so as to give a fair finish including centring, shuttering, strutting and propping etcetra with wooden battens and ballies, in all heights of propping and centring below supporting floor to ceiling upto any heights and removal of the same for insitu-reinforced concrete and plain concrete work in Edges of slabs and breaks in floors and walls upto all width and heights including all taxes,GST, including carriage of material and other incidentals within all leads and lifts and as per the direction of the Engineer-in-charge.

Providing and laying mechanically mixed and vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 330 Kg/Per cubic metre ( Three hundred thirty kilograme per cubic metre) and curing complete excluding cost of form work and reinforcement for reinforced concrete work in foundations, footings bases of columns and the like and mass concrete including carriage of material within all leads and lifts and as per the direction of the engineer-in -charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 330 Kg/Per cubic metre ( Three hundred twenty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in columns, pillars, posts and struts upto floor all levels as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 330 Kg/Per cubic metre ( Three hundred twenty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in suspended floors, roofs, landing, shelves and their support, balconies, beams, girders, bressumers and cantilever upto floor all levels as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying mechanically mixed & vibrated cement concrete work of grade M-20 (M-Twenty design mix) to obtain the minimum compressive strength of 20N/square MM (Twenty newton per square millimetre) with cement contents not less than 330 Kg/Per cubic metre ( Three hundred twenty kilograme per cubic metre) and curing complete excluding the cost of form work and reinforcement for reinforced concrete work in stair cases and connected work upto floor all levels as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete work of grade M-20 (M-twenty) design mix to obtain minimum compressive strength of 20N/mm square (twenty newton per square millimetre) with cement contents not less than 330 KG (Three hundred thirty kilogramme) / cum and curing complete including form work in string courses, coping, bed plates, anchor blocks plain window sill and in moulding as in cornices window sill etc the like upto floor all level as per the directions of the Engineer-in-charge including all taxes, GST, carriage of material within all leads and lifts and other incidentals.

Providing and laying mechanically mixed and vibrated cement concrete work of grade M-twenty design mix to obtain the minimum commpressive strength of 20 N /mm² (twenty newton per square millimetre ) cement contents of 320 Kg (three hundred ten kilogram) per cubic metre and curing complete excluding cost of form work and reinforcement for reinforced concrete work in walls ( any thickness but not less than 0.10 (zero point ten) Metre thickness) including attached pilasters buttersses, plinth and string courses etc. from top of foundation upto floor all levels including all taxes, GST, carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals as per HP:PWD specification.

Providing and laying mechanically mixed and vibrated plain cement concrete 1:4:8 (one cement isto four sand isto eight graded crushed stone agreegate 40 mm (forty millimetre) nominal size) and curing complete excluding the cost of form work in foudation and plinth including carriage of material, within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying mechanically mixed and vibrated cement concrete 1:6:12 (one cement isto six sand isto twelve graded crushed stone aggregate 40 mm (forty millimetre) nominal size) and curing complete excluding cost of centring and shuttering in foundation and plinth including carriage of material, within all leads and lifts within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing tor steel reinforcement for reinforced cement concrete work including straightening, bending, binding and placing in position complete as per the directions of the Engineer-in-charge including carriage of material, carriage of material within all leads and lifts and other incidentals.The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Random rubble masonry/polygonal rubble masonry (uncoursed / brought to courses ) with hard stones of approved quality in foundation and plinth including leveling up with cement concrete 1:6:12 (one cement isto six sand isto twelve graded stone agreegate 20mm (twenty millimetre) nominal size) at plinth level in cement mortar 1:6 (one cement isto six sand) as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Second class brick work using common brunt clay building bricks of approved quality in super structure above plinth level upto floor all levels in cement mortar 1:6 (one cement isto six sand) curing complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Half brick masonry using second class common brunt building brick of approved quality in super structure above plinth level upto floor all levels in cement mortar 1:4 (one cement isto four sand) curing complete including and carriage of material, as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing 35 mm (thirty five millimetre) flush door shutters core of black board construction with frame of first class hard wood and well matched firtst class Indian teak ply veneering with vertical grains of cross band and face vaneers on one face and commercial ply veneering with vertical grains of cross band on other face of shutters or as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing 12mm ( twelve millimetre) thick of Kit Vista water proof commercial board in lining of shelves / box for cup boards with butt joints and fixing with nails and screws etcetra complete the shelf shall be finished with 6/12mm (six / twelve millimetre) thick hard wood edging as per the direction of the engineer-in-charge, and drawing & design complete including all taxes and carriage of material within all leads and lifts and other incidentals.

Providing and fixing 19mm (ninteen millimetre) thick of Kit Vista water proof commercial board in shelves / box for cup boards with butt joints and fixing with nails and screws etcetra complete the shelf shall be finished with 6/12mm (six / twelve millimetre) thick hard wood edging as per the direction of the engineer-in-charge, and drawing & design complete including all taxes and carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing 6 mm ( six millimetre) ply wood lining of Kit Vista with butt jointing and nails (frame work and cove fillets to be measured and paid for separately) as per the direction of the engineer-in-charge, and drawing & design complete including all taxes and carriage of material within all leads and lifts and other incidentals.

Providing and fixing 65x35mm.(Sixty five into thirty five millimetre) special quality bright finished brass cup board locks or wardrobe locks with six levers including necessary screws etc. complete. (Indian make of approved quality) as per the direction of the Engineer-in-charge, and drawing & design complete including all taxes and carriage of material within all leads and lifts and other incidentals.

Providing and fixing anodized aluminium sliding door bolt anodized colour and shade with bolts and nuts screws etcetra complete 250 X 16 mm ( two hundred fifty into sixteen millimetre) within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing aluminium tower bolts (barrel type) anodized transparent or dyed to required shade and colour with screws etcetera complete 200 X 10 mm (two hundred into ten millimetre) within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etcetera complete 125 mm (one hundred twenty five millimetre) within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing aluminium handles anodized transparent or dyed to required colour and shade with necessary screws etcetera complete 75 mm ( seventy five millimetre) within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing bright finished or / and black enamelled iron Helical door spring 150mm (one hundred fifty millimetre) within all leads and lifts as per the direction of Engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing M.S. plain grills of required pattern in wooden frames of windows etc.with M.S.Flats, square or round bars with round headed bolts and nuts or by screws within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying 25 mm thick ( twenty five milimetre) Kota stone 55 x 55 cm ( fifty five into fifty five centimetre) minimum size slab flooring 20 mm ( twenty milimetre) thick base of cement mortor 1:4 ( one cement is to four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab. Including rubbing,polishing, cutting & moulded complete as per drawing, design & specification or directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Kota stone single slab flooring 20 mm ( twenty millimetre) (average) thick base of cement mortor 1:4 ( one cement isto four sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab in stair case Including rubbing,polishing, cutting & moulded complete as per drawing, design & specification or directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying 20mm. ( twenty millimetre) thick acid proof tiles of size upto 300 x 300mm ( three hundred into three hundred millimetre) of specified shade in floors, treads of steps and landing laid on a bed of 12mm ( twelve millimetre) thick cement mortar 1:3( one cement isto three sand) jointing with cement slurry mixed with pigment to match the shade of tiles as per drawing, design & specification or directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying 20 mm ( twenty millimetre) thick black granite stone in flooring 20mm ( twenty millimetre) (average)thickness base of cement mortar 1:3( one cement isto three sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of granite stone i/c rubbing and polishing complete including carriage of material within all leads and lifts and as per specification or as per the direction of the engineer-in-charge and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government.

Providing and laying Mandana red sand stone slab in treads and risers of steps on a bed of 20mm tick cement mortar 1:4 (1 cement : 4 sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab including preparing of nosing including rubbing and granite polish finish complete including and carriage of materials within all leads, lifts as per specification as per the direction of the Engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying 25mm (twenty five millimetre) thick kota stone single slab in risers of stpes, skiritng , dado and pillars laid on 12mm (twelve millimetre) (average) thick cement mortar 1:3 (one cement isto three sand) jointed with grey cement slurry mixed with pigment to match the shade of kota stone including rubbing and polishisng complete as per approved pattern upto all floor level including carriage of material within all leads and lifts and as per specification or as per the direction of the engineer-in-chief and other incidentals.The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

White glazed tiles 6mm (six millimetre) thick in skiriting or risers of steps and dado on 12mm (twelve millimetre) thick cement mortar 1:3 (one cement isto three sand) finished with flush pointing in white cement as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying white marble work (table rubbed and polished) having grey cement in 20mm thick ( twenty milimetre ) base in cement mortar 1:3(1cement:3sand) including jointing with cement mortar 1:2(1 white cement:2 marble dust)with an admixure of pigment to match the shade of the marble 20 mm (twenty millimetre) thick makrana marble as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a primming coat of red lead paint in trusses and trusses purlins in building including carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing steel door, windows, ventilaters and clerestory windows frame manufactured from M.S. channal 75x40mm (Seventy five into forty millimetre), size vertically welded with M.S. flat 75 X 4mm (Seventy five into four millimetre) for central frames with split to end tail to each jambs including joints and miterd and welded with 16 X 3.15mm (Sixteen into three point five millimetre) lugs 10cm (ten centimetre) long embedded in cement concrete block 15cm X 10cm X 10cm (Fifteen centimetre into ten centimetre into ten centimetre) size of 1:3:6 (one cement isto three sand isto six graded crushed stone aggregate twenty millimetre nominal size) with provision for locking arragnement and shock observor fixed with by mechanical means lugs and curing complete including applying a coat of approved steel primer after pretreatment of the surface as specified within all leads and lifts as per the direction of Engineer-in-Charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing steel glazed doors,windows and top hung ventilators of standerd rolled steel sections ,joints mitred and welded with 16x3.15 mm (sixteen into three point one five millimetre) lugs 10 cm ( ten c enetimetre) long embedded in cement concrete blocks 15 cmx10cmx10cm ( fifteen into ten into ten centimetre) size of 1:3:6( one cement isto three sand isto six graded stone aggregate 20mm ( twenty millimetre) nominal size)or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings,including providing and fixing of glass panes with glazing clips and special metal sesh putty as per the direction of Engineer-in-Charge.The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing Fixed Steel window steel glazed doors,windows and ventilators of standerd rolled steel sections ,joints mitred and welded with 16x3.15 mm (sixteen into three point one five millimetre) lugs 10 cm ( ten c enetimetre) long embedded in cement concrete blocks 15 cmx10cmx10cm ( fifteen into ten into ten centimetre) size of 1:3:6( one cement isto three sand isto six graded stone aggregate 20mm ( twenty millimetre) nominal size)or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings,including providing and fixing of glass panes with glazing clips and special metal sesh putty as per the direction of Engineer-in-Charge.The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing side hung steel glazed doors,windows and ventilators of standerd rolled steel sections ,joints mitred and welded with 16x3.15 mm (sixteen into three point one five millimetre) lugs 10 cm ( ten c enetimetre) long embedded in cement concrete blocks 15 cmx10cmx10cm ( fifteen into ten into ten centimetre) size of 1:3:6( one cement isto three sand isto six graded stone aggregate 20mm ( twenty millimetre) nominal size)or with wooden plugs and screws or rawl plug and screws or with fixing clips or with bolts and nuts as required and iron fittings,including providing and fixing of glass panes with glazing clips and special metal sesh putty as per the direction of Engineer-in-Charge. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing 0.60mm (zero point six zero millimetre) thick prepainted steel sheets of TATA Durashine in roofing with hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron (twenty micron) over 5 microns (five micron) primer coating and back coat of polyster of 5 microns (five micron) over 5 microns (five micron) primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet washers complete with all accesories as required including all taxes, carriage of material within all leads , lifts and as per specification approved drawing & Design or as per the direction of the engineer-in-chief and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing ridges or hips 60cm (sixty centimetre) overall 0.60mm (zero point six zero millimetre) thick prepainted steel sheets of TATA Durashine in roofing having proper gola shape hot dipped metallic zinc coated sheet with top coat of regular modified polyster (RMP) organic coating of 20 micron (twenty micron) over 5 microns (five microns) primer coating and back coat of polyster of 5 microns (five microns) over 5 microns (five microns) primer coating including fixing with prepainted iron J or L hooks, bolts and nuts 6mm (six millimetre) dia metre with prepainted limpet washers complete with all accesories as required including all taxes, carriage of material within all leads,lift and as per specification approved drawing & Design or as per the direction of the engineer-in-chief and other incidentals. The rate is including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 15cm (fifteen centimetre) wide 45cm (forty five centimetre) overall semicircular plain 0.63mm (zero point six three millimetre) thick G.I. sheet gutter with iron brackets 40x3mm (forty into three millimetre) size bolts and nuts and washers etcetera including making necessary conections with rain water pipe complete as per design including all taxes, carriage of material within all leads and lifts and as per specification or as per the direction of the engineer-in-chief and other incidentals. The rate including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing M.S. B.P. sheet 1.66mm (one point six six millimetre) any thickness in eaves board / facia / soffits / ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per specification including carriage of material within all leads and lifts and as per the direction of the engineer-in-chief and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing plain sheet with 19 x 19 mm (nineteen into nineteen millimetre) hollow aquare bar M.S. BP Sheet 1.66mm to 2mm ( One point six six to two millimetre) thick in eaves board/facia/soffits/ceiling including cutting, fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instruction of Engineer-in-charge (Base members of steel work shall be measured & paid separtely) The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing 50 mm(fifty millimetre) dia M.S. hollow pipe hand slip resistant with rounded at PWD level at 75 to 90cm ( seventy five to ninety centimetre) railing with 25 mm (twenty five millimetre) dia pipe fixed to vertical member @ 60 cm (sixty centimetre) centre to centre including all taxes carriage of materials within all leads and lifts as per the direction of Engineer-in-Charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing hand rail ready made M.S. hollow pipe D-section 50x50mm (fifty into fifty millimetre) diametre over 23cm.(twenty three centimetre) thick brick wall parapet with baluster 20x20mm (twenty into twenty millimetre) solid square bars etc. complete including all taxes and carriage of materials within all leads, lifts as per specification as per the direction of the Engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Applying priming coat over new wood and wood based surfaces after and including preparing the surface by thoroughly cleaning oil, grease, dirt and other foreign matter with Readymixed paint brushing wood primer pink as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Painting two coats (excluding priming coat ) on new wood and wood based surfaces with enamel paint to give an even shade including cleaning the surface of dirt, dust and other foreign matter, sand papering and stoping with enamel paint other than white as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Painting two coat (excluding priming coat) on new steel and other metal surfaces under coat with ready mixed paint brushing to give an even shade including cleaning the surface all dirt, dust and other foreign matter With white readymixed paint within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

6mm (six millimetre) thick cement plaster to ceiling in cement mortar 1:3 ( one cement isto six sand) as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

20 mm (twenty millimetre) cement plaster in single coat on fair side of brick /concrete /stone walls for interior plastering in groove upto floor two level including arrises internal rounded angles, chamfers and / or rounded angles not exceeding 80 mm ( eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement isto six sand) as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

15 mm ( fifteen millimetre) cement plaster in single coat on rough side of brick /concrete /stone walls for interior plastering upto floor two level including arrises internal rounded angles, chamfers and / or rounded angles not exceeding 80 mm ( eighty millimetre) in girth and finished even and smooth in cement mortar 1:6 (one cement isto six sand) as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Applying Birla white wall care putty over plastered surface after thoroughly brushing the surface free from mortar drops, dust loose materials and other foreign matter sand papered smooth to give final matter finish to the surface complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Finishing walls with Apex weather proof exterior grade emulsion of Asian paint or exterior emulsion of NAROLAC SURKSHA as per approved shade on undecorated wall surface (two or more coats) to give an even shade and final finish after thoroughly cleaning the surface to remove all dirt, dust and other foreign matter etc. including sand paper smooth complete as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Painting two coats with synthentic enamel paint (excluding priming coat )priming on new concrete masonry/plaster surfaces with readymixed paint brushing for use on floors to give an even shade including cleaning the surface of all dirt,dust and other foreign matter and sand papering as required as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Wall painting (two coats) with acrylic emulsion paint of approved brand and manufacture for interior grade on undecorated concrete/stone/plastered wall surfaces to give an even shade including thoroughly brushing the surface free from mortar dropping and other foreign matter and sand papered smooth including applying of putty a required for metling the surface .

Providing and fixing on wall faces PVC (D-plast) 100mm dia (one hundred millimetre diametre) rain water pipes working pressure not less than 4.5 Kg (four point five) kilogram per square metre including filling the joints with approved adhesive complete within all leads and lifts and as per the direction of the Engineer-in-Charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing on wall faces PVC (D-plast) 100mm (one hundred millimetre) dia PVC plain bend for rain water pipes including filling the joints with approved adhesive complete within all leads and lifts and as per the direction of the Engineer-in-Charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing plinth protection with inter locking paver 60 mm (sixty millimetre) thick of M-50 (M-Fifty ) Grade of approved make with 23 cm ( twenty three centimetre half rounded stone ware pipe for drainage purpose laid over including cement concrete 1:5:10 (one cement is to Five sand is to ten graded stone aggregate) as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing 6mmm(six millimetre) thick fibre cement board ceiling of everst approved quality with buttr and nails etc.complete including all taxes and carriage of materials within all leads, liftsas per specification as per the direction of the Engineer-in-charge and other incidentals.The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

Providing and fixing to wall, ceiling and floor galvanised mild steel tubes (medium grade) tube fittings and clamps including making good the wall, ceiling and floor 15 mm (fifteen millimetre) nominal bore including carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying in trenches galvanised mild steel tubes (medium grade) tube fittings (Earth work in trenches to be measured and paid for separately) 15 mm (fifteen millimetre) nominal bore including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Making connection of galvanised steel distribution branch with galvanised mild steel main 20 mm to 40 mm (twenty millimetre to forty millimetre) nominal bore by providing and fixing tee including cutting and threading the pipes complete including all taxes, carriage of material within all leads and lifts and as per the direction of the engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and placing in position 1000 (one thousand) litres net capacity PVC water storage tank of sintex ISI 12701 marked G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangment including hoisting upto all heights above ground level.as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and placing in position 500 ( Five hundred) litres net capacity PVC water storage tank of Sintex G.I. inlet and outlet connection, 15mm nominal bore ball valve and mosquito proof PVC cover with locking arrangment including hoisting upto all heights above ground level.as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.

Providing and fixing high pressure PVC spigot and socket of supreme make , waste and ventilating pipes ISI marked including fixing with approved adhesive 110 mm (one hundred ten millimetre) dia as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing high pressure PVC spigot and socket of supreme make , waste and ventilating pipes ISI marked including fixing with approved adhesive 75 mm ( seventy five millimetre) dia as per the directions of the Engineer-in-charge including all taxes carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing PVC 110x90mm (one hundred ten into ninety millimetre) dia Supreme make floor trap ISI Marked of self cleaning design including fixing with approved adhsive, cost of cutting making the walls and floors etc. complete including all taxes, carriage of material within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing PVC single equal branch plain of Supreme make ISI marked including fixing with approved adhesive 110 mm (one hundred ten millimetre) dia as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing PVC single equal branch plain of Supreme make including fixing with approved adhesive 75 mm ( seventy five millimetre) dia as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying PVC plain bend of supreme make ISI marked including fixing with approved adhesive etc. complete 110 mm (one hundred ten millimetre) dia as per the directions of the Engineer-in-charge includingall taxes, carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and laying PVC plain bend of Supreme make including fixing with approved adhesive etc. complete 75 mm ( seventy five millimetre) dia as per the directions of the Engineer-in-charge includingall taxes, carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing PVC P or S trap for water closet (squatting pan ) ISI marked including jointing the trap with the pan and PVC pipe with approved adhesive etc. complete 150mm (one hundred fifty millimetre) dia as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing vitreous China water closet squatting pan (Indian type W.C. pan) Orrisa pattern No. 2004 of size 58x40 cm. of hindware in white shade as per specification or as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing PTMT coloured/ white high density polythene / poly prolylene 10 litre (ten litre) capacity low level P.V.C. cistern plus) flushing cistern of hindware with a pair of C.I. or M.S. brackets complete with fitting such as lead valve syphon, 15mm (fifteen millimetre) dia PVC wall valve , coupling for connection with inlet, outlet and overflow pipes 40mm (forty millimetre) dia C.P. flush bend including cutting holes and making good the same (overflow pipe to be measured and paid for separately) as per specification as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing viterous China bowl pattern urinal of Hindware including connection the urinal with waste pipe by means of white lead mixed with chopped hemp (waste pipe to be measured and paid for separately) Flat type of size 430mm X 260mm X 350mm ( four hundred thirty into two hundred sixty into three hundred fifty) in white colour as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing vitreous China wash basin of Hindware with single hole for pillar tap with C.I. or M.S. brackets painted white including cutting holes and making good the same but excluding fittings Flat back 630mm X 450 mm (six hundred thirty millimetre into four hundred fifty millimetre) as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing vitreous China wash down water closet (European type W.C. pan)(prima) number 2090 of hindware of approved sahde having dual flus cistern with integral P or S trap including jointing the trap with soil pipe in cement mortar 1:1 (one cement isto one sand). Seat and cover to be measured and paid for separately. Ordinary closet.as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing plastic seat (Solid) type and cover for wash down water closet with C.P. Brass hinges and rubber buffers as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing vitreous China pedestal for wash basin of Hindware recessed at the back for the reception of pipes and fittings as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing C.P. brass waste of 32mm (thirty two millimetre) dia size for sink or wash basin.as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals.The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing 15 mm (fifteen millimetre) nominal bore C.P. brass flush pipe / spreaders for urinal with fitting such as unions, clamps etcetra (all in C.P. Brass) including cutting holes and making good the same as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.

Providing and fixing charomium plated brass soap dish of Jaquar make with C.P. brass brackets fixed to wooden cleats with C.P. brass screws as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing 600mm X 450 mm (six hundred millimetre into four hundred fifty millimetre) bevelled edge mirror of superior glass mounted on 6mm (six millimetre)thick A.C. sheet or plywood sheet and fixed to wooden plugs with C.P. brass screws and washers.as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing C.P. brass bib tap with capstan head of Jaquar make of 15 mm (fifteen millimetre) dia with capaston head as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing C.P. brass pillar tap with capstan head of jaquar make of 15mm (fifteen millimetre) dia.as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing C.P. brass angle valve 15mm (fifteen millimetre) dia of jaquar make as per the directions of the Engineer-in-charge including carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing PVC connection with brass union 45cm. (forty five centimetre) Long and 15mm (fifteen millimetre) dia as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing C.P. brass full way valve with wheel of jaquar make of 15mm (fifteen millimetre) nominal bore as per the directions of the Engineer-in-charge including all taxes, carriage of material within all leads and lifts and other incidentals.The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Construting manhole with RCC top slab in 1:2:4 ( one cement isto two sand isto four graded stone aggregate) 20mm (twenty millimetre nominal size) ,foudnation concrete 1:4:8 (one cement isto four sand isto eight graded stone aggregate 40mm (forty millimetre nominal size) in side plastering 15mm (fiften milliemtre) thick with cement mortar 1:3 (one cement isto three sand) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 mix (one cement isto two sand isto four grade stone aggregate 20mm (twenty millimetre)nominal size finished smooth complete including curing and testing having inside size 800mmx800mm (eight hundred millimeter into eight hundred millimeter) and 500mm (five hundred millimetre) deep including C.I. cover with frame (light duty single seal pattern one) 455mm x610mm (four hunded fifty five millimetre into six hundred ten millimetre) internal dimension total weight of cover and frame to be not less than 38 kg (thirty eight kilogram )weight of cover 23 kg (twenty three kilogram) and weight of frame 15 kg (fifteen kilogram) with 23cm. thick brick wall of approved quality in cement mortar 1:3 (one cement isto three sand) within all leads and lifts and as per the direction of the Engineer-in-charge and other incidentals. The rate is including octroi, royality,Malkana,toll tax, GST tax or other taxes imposed by the Government.

Providing and fixing in position water lifting pump (toollu pump) having 1.00 (one) horse power capacity of Kirloskar or equivilent make ISI mark including all necessary fitting required at site complete in all respect as directed by the Engineer-in-Charge, including carriage of materials within all leads, lifts and other incidental. The rate including octroi, royality, Malkana, toll tax, GST or any other taxes imposed by the Government .

construction

Jagpal Singh